CompTIA Server+

W
CompTIA Server+
Certification
Instructors Edition
PR
EV
IE
2009 Edition
NOT FOR PRINTING OR INSTRUCTIONAL USE
CompTIA Server+ Certification, 2009 Edition

Jon Winder
Vice President, Product Development:

Vice President, Operations:
President, Axzo Press:
Charles G. Blum
Josh Pincus
Director of Publishing Systems Development:

Developmental Editors:
Dan Quackenbush
Andy LaPage, Tim Poulsen, Judi Kling
Copyeditor:
Catherine Oliver
Cliff Coryea
IE
Keytester:
COPYRIGHT 2010 Axzo Press. All rights reserved.
No part of this work may be reproduced, transcribed, or used in any form or by any meansgraphic, electronic, or
mechanical, including photocopying, recording, taping, Web distribution, or information storage and retrieval
systemswithout the prior written permission of the publisher.
For more information, go to www.axzopress.com.
Trademarks
EV
ILT Series is a trademark of Axzo Press.

Some of the product names and company names used in this book have been used for identification purposes only and
may be trademarks or registered trademarks of their respective manufacturers and sellers.
Disclaimers
We reserve the right to revise this puThe logo of the CompTIA Authorized Quality Curriculum (CAQC) program and
the status of this or other training material as Authorized under the CompTIA Authorized Quality Curriculum
program signifies that, in CompTIAs opinion, such training material covers the content of CompTIAs related
certification exam.
The contents of this training material were created for the CompTIA Server+ exam, 2009 Edition (SK0-003),
covering CompTIA certification objectives that were current as of March 2010.blication and make changes from time
to time in its content without notice.
PR
ISBN 10: 1-4260-1906-8

ISBN 13: 978-1-4260-1906-7
Printed in the United States of America
1 2 3 4 5 GL 06 05 04 03
Introduction
Topic A:
Topic B:
Topic C:
Topic D:
Contents
iii
About the manual............................................................................... iv

Setting student expectations .............................................................. ix
Classroom setup................................................................................ xiv
Support.............................................................................................. xix
Deploying the chassis
1-1
IE
Topic A: Form factors...................................................................................... 1-2

Topic B: Power supplies ................................................................................. 1-12
Topic C: Cooling systems............................................................................... 1-21
Unit summary: Deploying the chassis............................................................. 1-28
Selecting CPUs and motherboards
2-1
Topic A: Central processing units.................................................................... 2-2

Topic B: Packaging and slots ......................................................................... 2-11
Topic C: Motherboards................................................................................... 2-16
Unit summary: Selecting CPUs and motherboards ......................................... 2-21
EV
Managing the BIOS
3-1
Topic A: The BIOS and CMOS....................................................................... 3-2

Topic B: The POST and boot processes ......................................................... 3-13
Unit summary: Managing the BIOS................................................................ 3-18
Selecting memory
4-1
Topic A: Memory ............................................................................................ 4-2

Topic B: Memory packaging .......................................................................... 4-11
Unit summary: Selecting memory................................................................... 4-17
Troubleshooting methodology
5-1
PR
Topic A: Troubleshooting models ................................................................... 5-2

Topic B: Troubleshooting toolkits.................................................................. 5-18
Topic C: Troubleshooting system components .............................................. 5-23
Unit summary: Troubleshooting methodology ............................................... 5-44
Installing expansion cards
6-1
Topic A: Buses................................................................................................. 6-2

Topic B: Drive adapters.................................................................................. 6-18
Topic C: Multimedia expansion devices ........................................................ 6-35
Topic D: Troubleshooting expansion cards .................................................... 6-47
Unit summary: Installing expansion cards ...................................................... 6-56
Installing data storage devices
7-1
Topic A: Installing storage devices.................................................................. 7-2

Topic B: Selecting RAID technologies .......................................................... 7-20
Topic C: Troubleshooting data storage........................................................... 7-28
Unit summary: Installing data storage devices................................................ 7-46
ii
Installing a network operating system
8-1
Networking
Topic A: Server roles....................................................................................... 8-2

Topic B: Virtualization................................................................................... 8-10
Topic C: Installing Linux ............................................................................... 8-23
Topic D: Installing Windows Server .............................................................. 8-34
Unit summary: Installing a network operating system ................................... 8-49
9-1
Topic A: Networking essentials ...................................................................... 9-2

Topic B: Networking utilities......................................................................... 9-33
Topic C: Troubleshooting .............................................................................. 9-45
Unit summary: Networking ............................................................................ 9-50
Managing a network server
10-1
IE
Topic A: User management............................................................................ 10-2

Topic B: Resource management.................................................................... 10-29
Topic C: Monitoring and management ......................................................... 10-41
Unit summary: Managing a network server................................................... 10-54
Documenting and planning
11-1
EV
Topic A: Documenting the IT environment ................................................... 11-2

Topic B: Planning and implementing change ................................................ 11-8
Topic C: Managing physical access and security.......................................... 11-12
Unit summary: Documenting and planning ................................................... 11-20
Preparing for disaster
12-1
Topic A: Backing up data............................................................................... 12-2

Topic B: Server redundancy and other disaster precautions ......................... 12-31
Topic C: Developing a disaster recovery plan .............................................. 12-39
Unit summary: Preparing for disaster ............................................................ 12-44
Certification exam objectives map
A-1
Topic A: Comprehensive exam objectives ...................................................... A-2
CompTIA Server+ acronyms
B-1
Topic A: Acronym list..................................................................................... B-2
PR
Course summary
S-1
Topic A: Course summary............................................................................... S-2

Topic B: Continued learning after class .......................................................... S-5
Glossary
G-1
Index
I-1
iii
Introduction
After reading this introduction, you will know

how to:
IE
A Use ILT Series manuals in general.

B Use prerequisites, a target student
description, course objectives, and a skills

inventory to properly set students
expectations for the course.
C Set up a classroom to teach this course.
EV
D Get support for setting up and teaching this
PR
course.
iv
Topic A: About the manual
ILT Series philosophy

Our goal is to make you, the instructor, as successful as possible. To that end, our
manuals facilitate students learning by providing structured interaction with the
software itself. While we provide text to help you explain difficult concepts, the handson activities are the focus of our courses. Leading the students through these activities
will teach the skills and concepts effectively.
IE
We believe strongly in the instructor-led class. For many students, having a thinking,
feeling instructor in front of them will always be the most comfortable way to learn.
Because the students focus should be on you, our manuals are designed and written to
facilitate your interaction with the students, and not to call attention to manuals
themselves.
We believe in the basic approach of setting expectations, then teaching, and providing
summary and review afterwards. For this reason, lessons begin with objectives and end
with summaries. We also provide overall course objectives and a course summary to
provide both an introduction to and closure on the entire course.
Our goal is your success. We encourage your feedback in helping us to continually
improve our manuals to meet your needs.
EV
Manual components
The manuals contain these major components:

Table of contents
Introduction
Units
Appendices
Course summary
Glossary
Index
Each element is described below.
PR
Table of contents
The table of contents acts as a learning roadmap for you and the students.
Introduction
The introduction contains information about our training philosophy and our manual
components, features, and conventions. It contains target student, prerequisite,
objective, and setup information for the specific course. Finally, the introduction
contains support information.
Introduction
Units
Units are the largest structural component of the actual course content. A unit begins
with a title page that lists objectives for each major subdivision, or topic, within the unit.
Within each topic, conceptual and explanatory information alternates with hands-on
activities. Units conclude with a summary comprising one paragraph for each topic, and
an independent practice activity that gives students an opportunity to practice the skills
theyve learned.
The conceptual information takes the form of text paragraphs, exhibits, lists, and tables.
The activities are structured in two columns, one telling students what to do, the other
providing explanations, descriptions, and graphics. Throughout a unit, instructor notes
are found in the left margin.
Appendices
IE
An appendix is similar to a unit in that it contains objectives and conceptual

explanations. However, an appendix does not include hands-on activities, a summary, or
an independent practice activity.
Course summary
EV
This section provides a text summary of the entire course. It is useful for providing
closure at the end of the course. The course summary also indicates the next course in
this series, if there is one, and lists additional resources students might find useful as
they continue to learn about the software.
Glossary
The glossary provides definitions for all of the key terms used in this course.
Index
PR
The index at the end of this manual makes it easy for you and your students to find
information about a particular software component, feature, or concept.
vi
Manual conventions
Item
Description
Italic text
In conceptual text, indicates a new term or feature.
Bold text
In unit summaries, indicates a key term or concept. In

an independent practice activity, indicates an explicit
item that you select, choose, or type.
Code font
Indicates code or syntax.
IE
Instructor note/icon
Weve tried to keep the number of elements and the types of formatting to a minimum
in the manuals. We think this aids in clarity and makes the manuals more classically
elegant looking. But there are some conventions and icons you should know about.
Longer strings of
code will look
like this.
Instructor notes.
In the hands-on activities, any code thats too long to fit

on a single line is divided into segments by one or more
continuation characters (). This code should be
entered as a continuous string of text.
In the left margin, provide tips, hints, and warnings for
the instructor.
In the left column of hands-on activities, bold sans-serif

text indicates an explicit item that you select, choose,
or type.
EV
Select bold item
Keycaps like e
Indicate a key on the keyboard you must press.
Warning icon.
Warnings prepare instructors for potential classroom

management problems.
Tip icon.
Tips give extra information the instructor can share

with students.
PR
Setup icon.
Projector icon.
Setup notes provide a realistic business context for

instructors to share with students, or indicate additional
setup steps required for the current activity.
Projector notes indicate that there is a PowerPoint slide
for the adjacent content.
Introduction
vii
Hands-on activities
Do it!
A-1:
Creating a commission formula
Heres how
1 Open Sales
Heres why
This is an oversimplified sales compensation

worksheet. It shows sales totals, commissions,
and incentives for five sales reps.
IE
Take the time to make

sure your students
understand this
worksheet. Well be here a
while.
The hands-on activities are the most important parts of our manuals. They are divided
into two primary columns. The Heres how column gives short directions to the
students. The Heres why column provides explanations, graphics, and clarifications.
To the left, instructor notes provide tips, warnings, setups, and other information for the
instructor only. Heres a sample:
2 Observe the contents of cell F4
The commission rate formulas use the name

C_Rate instead of a value for the commission
rate.
EV
For these activities, we have provided a collection of data files designed to help students
learn each skill in a real-world business context. As students work through the activities,
they will modify and update these files. Of course, students might make a mistake and
therefore want to re-key the activity starting from scratch. To make it easy to start over,
students will rename each data file at the end of the first activity in which the file is
modified. Our convention for renaming files is to add the word My to the beginning
of the file name. In the above activity, for example, students are using a file called
Sales for the first time. At the end of this activity, they would save the file as My
sales, thus leaving the Sales file unchanged. If students make mistakes, they can start
over using the original Sales file.
PR
In some activities, however, it might not be practical to rename the data file. Such
exceptions are indicated with an instructor note. If students want to retry one of these
activities, you will need to provide a fresh copy of the original data file.
viii
PowerPoint presentations
The ILT Series PowerPoint add-in
Each unit in this course has an accompanying PowerPoint presentation. These slide
shows are designed to support your classroom instruction while providing students with
a visual focus. Each presentation begins with a list of unit objectives and ends with a
unit summary slide. We strongly recommend that you run these presentations from the
instructors station as you teach this course. A copy of PowerPoint Viewer is included,
so it is not necessary to have PowerPoint installed on your computer.
The CD also contains a PowerPoint add-in that enables you to do two things:
Create slide notes for the class
Display a control panel for the Flash movies embedded in the presentations
EV
IE
To load the PowerPoint add-in:

1 Copy the Course_ILT.ppa file to a convenient location on your hard drive.
2 Start PowerPoint.
3 Choose Tools, Macro, Security to open the Security dialog box. On the Security
Level tab, select Medium (if necessary), and then click OK.
4 Choose Tools, Add-Ins to open the Add-Ins dialog box. Then, click Add New.
5 Browse to and double-click the Course_ILT.ppa file, and then click OK. A
message box will appear, warning you that macros can contain viruses.
6 Click Enable Macros. The Course_ILT add-in should now appear in the
Available Add-Ins list (in the Add-Ins dialog box). The x in front of
Course_ILT indicates that the add-in is loaded.
7 Click Close to close the Add-Ins dialog box.
After you complete this procedure, a new toolbar will be available at the top of the
PowerPoint window. This toolbar contains a single button labeled Create SlideNotes.
Click this button to generate slide-notes files in both text (.txt) and Excel (.xls) format.
By default, these files will be saved to the folder that contains the presentation. If the
PowerPoint file is on a CD-ROM or in some other location to which the slide-notes files
cannot be saved, you will be prompted to save the presentation to your hard drive and
try again.
PR
When you run a presentation and come to a slide that contains a Flash movie, you will
see a small control panel in the lower-left corner of the screen. You can use this panel to
start, stop, and rewind the movie, or to play it again.
Introduction
ix
Topic B: Setting student expectations
Properly setting students expectations is essential to your success. This topic will help
you do that by providing:
Prerequisites for this course
A description of the target student
A list of the objectives for the course

A skills assessment for the course
Course prerequisites
IE
Students taking this course should be familiar with personal computers and the use of a
keyboard and a mouse. Furthermore, this course assumes that students have completed
the following courses or have equivalent experience:
CompTIA A+ Certification
Target student
EV
This course will prepare students for the CompTIA Server+ certification exam (2009
objectives). It is designed for students seeking foundation-level server administration
skills and knowledge. The associated exam is targeted toward individuals with 1824
months of IT experience. Students with an A+ certification or commensurate experience
will be well placed for this course.
Course objectives
You should share these overall course objectives with your students at the beginning of
the day. This will give the students an idea about what to expect, and it will help you
identify students who might be misplaced. Students are considered misplaced when they
lack the prerequisite knowledge or when they already know most of the subject matter
to be covered.
After completing this course, students will know how to:
Describe server-related form factors, power supplies, and cooling systems.
PR
Identify various motherboards and CPUs.

Configure the PCs BIOS and boot the computer.
Identify various types of memory.
Describe various troubleshooting methodologies.
Install expansion cards.
Install data storage devices.
Install network operating systems.
Identify network components and valid network addresses, and troubleshoot
basic network connectivity problems.
Monitor and manage the Windows operating system.
Document the IT environment, plan and implement change, and manage
physical security.
Prepare for disaster through backups, redundancy, and planning.
How to become CompTIA certified

To achieve CompTIA Server+ certification, a student must register for and pass the
CompTIA Server+ (2009 Edition) exam.
IE
In order to become CompTIA certified, students must:

1 Select a certification exam provider. For more information, students should visit
http://www.comptia.org/certifications/testprep.aspx.
2 Register for and schedule a time to take the CompTIA certification exam(s) at a
convenient location.
3 Read and sign the Candidate Agreement, which will be presented at the time of
the exam. The complete text of the Candidate Agreement can be found at
http://www.comptia.org/certifications/policies/agreement.aspx.
4 Take and pass the CompTIA certification exam(s).
For more information about CompTIAs certifications, such as its industry acceptance,
benefits, or program news, students should visit
http://www.comptia.org/certifications.aspx.
CompTIA is a not-for-profit information technology (IT) trade association. CompTIAs
certifications are designed by subject matter experts from across the IT industry. Each
CompTIA certification is vendor-neutral, covers multiple technologies, and requires
demonstration of skills and knowledge widely sought after by the IT industry.
PR
EV
To contact CompTIA with any questions or comments, please call (630) 678-8300 or
e-mail questions@comptia.org.
xi
Introduction
Skills inventory
Use the following form to gauge students skill levels entering the class (students have
copies in the introductions of their student manuals). For each skill listed, have students
rate their familiarity from 1 to 5, with five being the most familiar. Emphasize that this
is not a test. Rather, it is intended to provide students with an idea of where theyre
starting from at the beginning of class. If a student is wholly unfamiliar with all the
skills, he or she might not be ready for the class. A student who seems to understand all
of the skills, on the other hand, might need to move on to the next course in the series.
Skill
Describing the dimensions associated with rack units (1U, 2U, and
so forth)
IE
Identifying power connectors, power supply characteristics, and

suitable power conditions for a server environment
Selecting appropriate computer, rack, and row cooling solutions

Identifying electrostatic discharge and following ESD safe
practices while working with computer components
Describing the purpose and features of PC power supplies
EV
Describing the function and features of CPUs, identifying a CPU,

and classifying CPUs according to their specifications
Describing motherboards, their components, and their form factors

Accessing the BIOS setup utility, modifying hardware
configuration values, and researching BIOS updates
Explaining the POST and boot processes
Describing the function of memory and differentiating among

various types of memory chips
Differentiating among the various memory packages
PR
Describing the primary types of buses, and defining the terms

interrupt, IRQ, I/O address, DMA, and base memory address
Describing the features and functions of the PCI bus
Defining the common drive interfaces
Identifying and connecting USB ports, cables, and connectors
Identifying and connecting FireWire ports, cables, and connectors
Identifying and connecting multimedia ports
Describing hard drives, partitions, and file systems
xii

Skill
Using removable drives

Maintaining hard disks
Identifying operating system problems
Describing optical data storage and using optical drives and discs
Examining proper methods for disposing of computer equipment

Backing up your computer
IE
Interpreting common hardware-related symptoms and their causes

Describing troubleshooting models and problem-tracking systems
Identifying characteristics of various network technologies
Describing the functions of the protocols in the TCP/IP protocol

suite
Configuring TCP/IP
EV
Comparing wired network connections
Describing how various types of addresses are used to identify

devices on a network
Troubleshooting common network-related problems and their
causes
Monitoring system performance
Managing the operating system via SNMP, WBEM, and WMI

Describing networking models
PR
Identifying the basic components of a network

Explaining server roles
Exploring the purposes and application of virtualization

Investigating storage virtualization
Considering the security implications of virtualization
Evaluating virtualization best practices
Exploring Linux distributions
Installing Linux
xiii
Introduction
Skill
Installing Windows Server 2008
Logging onto Debian
Configuring computer information

Configuring Windows Update
Searching for Windows updates
Customizing a Windows Server installation
IE
Discussing malware protection software
PR
EV
Implementing various server access methods
xiv
Topic C: Classroom setup
Hardware requirements
All our courses assume that each student has a personal computer to use during the
class. Our hands-on approach to learning requires that they do. This topic gives
information on how to set up the classroom to teach this course. It includes minimum
requirements for the students personal computers, setup information for the first time
you teach the class, and setup information for each time you teach after the first time
you set up the classroom.
IE
Students can work in pairs. Each lab station will need at least one server computer for
each student. The instructor will need a server to match student lab stations. You will
need an additional Linux-compatible computer for each lab station so students can
install Linux during Unit 8 (Installing a network operating system).
Lab station servers should have:
A PS/2 keyboard and a mouse

At least 1 GHz 32-bit or 1.4 GHz 64-bit processor (2 GHz or faster
recommended)
At least 1 GB RAM (2 GB or greater recommended)
At least 40 GB hard drive
EV
A DVD-ROM drive
SVGA monitor at 1024768 or higher
Additional equipment
You will need this additional equipment for each student. If you dont have enough
hardware for each student to complete an activity on his or her own Student PC, have
students complete the activity and independent practice activities in small groups at a
Group PC.
Computer toolkit with assorted screwdrivers (including nonmagnetic Phillipshead screwdriver)
A second, unpartitioned hard drive for each student PC, with related media and
cables
PR
External storage device, such as a USB hard drive or flash drive.
Any expansion card, with associated software, and any required adapters
or components
Bootable CD-ROM. An operating system install disc may be used.

Bootable floppy disk, if student machines have floppy drives
Network cable (RJ-45 connectors)
KVM switch and necessary cabling
Introduction
xv
Software requirements
You will need the following software:
Windows Server 2008 Standard

Debian 5.0 (Lenny); newer versions will probably work, but the Linux
installation activity in Unit 8 might not key exactly as written.
Network requirements
The following network components and connectivity are also required for this course:
IE
Internet access, for the following purposes:

Downloading the latest critical updates and service packs from
www.windowsupdate.com
Completing activities within the units.
Classroom computers need to be connected through TCP/IP and must receive IP

addressing information from a DHCP server.
First-time setup instructions
PR
EV
The first time you teach this course, you will need to perform the following steps to set
up each student computer.
1 Install Windows Server 2008 Standard Edition on the instructor and student
computers.
a Select the appropriate language, time and currency, and keyboard or input
method for your location.
b Select Windows Server 2008 Standard Edition (Full Installation).
c Accept the license terms.
d Click Custom, and create at least a 40 GB partition.
e When prompted to change the users password, click OK. For the
Administrator account, enter and confirm a password of !pass1234. Press
Enter and click OK.
f If prompted to install drivers, install them now.
2 Use the Initial Configuration Tasks window to configure the following settings.
a Set the time zone appropriate for your location.
b Configure networking so the instructor and student computers have
dynamic IP addressing information from a DHCP server (including default
gateway and DNS server address) and can connect to the Internet. Internet
connectivity is required throughout the course.
c Name the computer WINSRV##, where ## is the number of the lab station.
Name the instructor server WINSRV00. Leave the computer in the default
workgroup named WORKGROUP. Restart the computer when prompted.
d Log back on as Administrator with the password !pass1234. In the Initial
Configuration Tasks window, select Do not show this window at logon,
and click Close.
3 Open Device Manager and ensure that all devices were installed. Install any
additional drivers, if necessary.
4 In Server Manager, in the details pane, click Configure IE ESC. Turn of ESC for
both administrators and users. Click OK.
xvi
Setup instructions for every class
Every time you teach this course you will need to perform the steps in the section titled
First-time setup instructions.
Setting up troubleshooting activities
Some of the units contain a troubleshooting activity. In these activities, students are
asked to solve problems related to the material of that unit. This section presents ideas
for problems that can be implemented.
IE
We suggest two ways to implement these problems. In the first, you would send
students off to a break while you induce these problems in their computers. In the
second scenario, you would divide students into two groups. Each group would induce
problems in a set of computers. The groups would switch places and solve the problems
that the other group created.
When determining which problems to implement, make sure you consider the technical
proficiency of your students.
Unit 5: Troubleshooting methodology
For the Topic C activity entitled Troubleshooting power supply problems, you can
implement one or more of these problems:
Unplug the computer from the wall outlet.
EV
Plug the computer into a non-functioning UPS device or surge protector.

Disconnect the power supply from the motherboard.
Disconnect the hard disk from the power supply.
Replace the power supply with a non-functioning power supply.
For the Topic C activity entitled Troubleshooting problems with system startup, you
can implement one or more of these problems:
Switch the keyboard and mouse cables so that each one is plugged into the
others port.
Substitute a keyboard with a stuck key or some other defect that would cause the
POST to fail.
Replace the CMOS battery with a dead battery, or simply remove the battery
from the motherboard.
PR
Reset one or more BIOS setup values that would leave the computer unbootable
or unusable. For example, change the boot drive order, disable the hard drive
controller (if its the boot device), or configure the on-board video controller to
an extremely low-resolution display.
Install a defective memory module so that the POST fails when it tests memory.
(Advanced) Flash the BIOS with an incorrect or outdated version.
Introduction
xvii
For the Topic C activity entitled Troubleshooting memory, you can implement one or
more of these problems:
Replace one or more memory modules with a defective memory module.
Loosen a module in its socket so that its pins dont make proper connections.
Reconfigure the BIOS with an incorrect quantity of memory.
Install the incorrect type of module for the computerinstall modules that are
too slow, implement parity when the motherboard doesnt, or dont implement
parity when the motherboard does, and so forth.
Install modules of different size or speed within a single bank.
Remove one of the modules from a bank.
Unit 9: Networking
IE
For the Topic C activity entitled Troubleshooting network problems, you can
implement one or more of these problems:
Disconnect or loosely connect the network cable on either the NIC end or the
hub end of the connection.
Change the IP address to an invalid address for the network.
Change the subnet mask to one that is invalid for the network.
Replace the network cable with a crossover Ethernet cable.
Replace the network cable with a broken network cable.
EV
Disable the network card in the systems BIOS.

Install the wrong driver for the network card.
Replace the NIC with a non-working NIC.

Configure the DHCP server to hand out invalid IP addresses, an invalid gateway
address, or an invalid DNS server address.
Disconnect or disable the connection between the classroom network and the
Internet.
Create a local routing table with invalid routing information for the default
gateway or a specific host.
Downloading the PowerPoint presentations
PR
If you dont have the CD that came with this manual, you can download the PowerPoint
presentations for this course. Heres what you do:
1 Connect to www.axzopress.com.
2 Under Downloads, click Instructor-Led Training.
3 Browse the subject categories to locate your course. Then click the course title to
display a list of available downloads. (You can also access these downloads
through our Catalog listings.)
4 Click the link(s) for downloading the PowerPoint presentations, and follow the
instructions that appear on your screen.
xviii
CertBlaster software
PR
EV
IE
CertBlaster pre- and post-assessment software is available for this course. To download
and install this free software, students should complete the following steps:
1 Go to www.axzopress.com.
2 Under Downloads, click CertBlaster.
3 Click the link for CompTIA Server+ 2009
4 Save the .EXE file to a folder on your hard drive. (Note: If you skip this step,
the CertBlaster software will not install correctly.)
5 Click Start and choose Run.
6 Click Browse and then navigate to the folder that contains the .EXE file.
7 Select the .EXE file and click Open.
8 Click OK and follow the on-screen instructions.
Introduction
xix
Topic D: Support
Contacting us
Your success is our primary concern. If you need help setting up this class or teaching a
particular unit, topic, or activity, please dont hesitate to get in touch with us.
Please contact us through our Web site, www.axzopress.com. You will need to provide
the name of the course, and be as specific as possible about the kind of help you need.
Instructors tools
PR
EV
IE
Our Web site provides several instructors tools for each course, including course
outlines and answers to frequently asked questions. To download these files, go to
www.axzopress.com. Then, under Downloads, click Instructor-Led Training and
browse our subject categories.
PR
EV
IE
xx
Unit 1
11
Unit time: 90 minutes
Complete this unit, and youll know how to:
IE
A Describe the form and features of typical
cases and racks.
B Identify power connectors, power supply
characteristics, and the features needed to

provide proper power in a server
environment.
C Identify and select appropriate cooling
PR
EV
systems for standalone and rack-mounted

server systems.
12
Topic A: Form factors
This topic covers the following CompTIA Server+ (2009 Edition) exam objective.
#
Objective
1.2
Deploy different chassis types and the appropriate components

Form factor
Space utilization (U size, height, width, depth)

Redundant power
Shutoff switches; chassis intrusion
Power buttons
IE
Reset buttons
Diagnostic LEDs
Expansion bays
Client form factors
Computer cases enclose a computers components. The various classes of computers

clients, servers, notebooksuse different types of cases, though types overlap classes.
The following table describes the common form factors for client computer cases.
EV
Explanation
Description
Desktop
Once the most popular form factor, but rare today. The case was designed
to lie horizontally on a desk, with the monitor sitting atop it. Floppy and
CD drives were mounted horizontally so they would work correctly in a
case in this orientation.
Tower
An upright version of the desktop case (it stands vertically, rather than
horizontally). Its designed to sit on the floor or on a shelf. Drives and other
components are mounted such that theyre horizontal in the tower.
Dimensions are in the range of 20" tall by 8" wide by 18" deep or larger.
Mid-tower
A smaller version of the tower case. Dimensions are in the range of 18" tall
by 8" wide by 18" deep.
PR
Form factor
The Mac Mini is an

example of a very small
cube case, just 6.5" wide
and deep by 2" tall.
Mini-tower
A still smaller version of the tower case. Dimensions are in the range of 16"
tall by 8" wide by 16" deep or smaller.
Brick (or cube)
A small case, more cube-shaped than a typical tower case. This case style
was introduced many years ago, but is regaining favor among some users
and manufacturers. Dimensions are in the range of 8" tall by 12" wide by 8"
deep or smaller.
Laptop or
notebook
A self-contained portable computer. All of the core hardware

componentsmonitor, keyboard, hard driveare integrated into the unit.
Additional peripherals are connected via expansion ports or installed into
mounting bays. A distinction used to be made between laptops and
notebooks, with the latter being the smaller form factor.
13
Server form factors
Computer racks
Many servers use the form factors described in the preceding table: tower and midtower form factors, for example, are commonly used by servers. A rack-mounted
computer is an example of a server that uses a very different form factor.
EV
IE
A computer rack is a standardized mounting unit for computing devices, such as

servers, routers, internetworking devices, fans, and so forth. Standard racks, as defined
by the EIA-310 specification, are 19" wide (23" wide racks are used in some
telecommunications applications). This measurement is made from the outsides of the
two mounting rails, which are 0.625" wide each. This makes for a 17.75" separation
between rails, and 18.3" between the centers of the mounting holes.
Exhibit 1-1: A typical computer rack (photo by David Lippincott for Chassis Plans)
PR
The depth of racks varies. Commonly, the distance between the front and back sets of
rails is either 31.5 or 39.4 inches. (Some racks dont provide back rails and are
described as two-rail racks.) The overall outside dimensions of a rack are larger and
vary by manufacturer and style. The extra width or depth provides space for air flow
(for cooling) and for chases for running wires and cables. A column of electrical outlets
is typically mounted along the inside of the back of the rack.
14

Rack units
EV
IE
As shown in Exhibit 1-2, mounting holes are provided in groups of three, spaced 0.625"
on center, with a space of 0.5" between groups. This arrangement leads to standard rack
units, which are measures of vertical height. One rack unit (1U) is 1.75", which is the
distance between three-hole groups. The common U sizes are shown in the following
diagram.
Exhibit 1-2: Server-rack rail dimensions and their correspondence to U size
PR
Server manufacturers normally design their servers to occupy whole-number U spaces.

Thus, you will see devices described as 1U, 2U, and so forth. Rarely, you will encounter
devices that occupy a fractional size, such as 1.5U. Most servers are 1U or 2U.

Do it!
A-1:
15
Comparing form factors
Questions
Answers
1 What form factor is your PCs

case?
2 If your instructor has cases of
other form factors available,
compare those with your case
With standard heights, you can plan your space

needs and know in advance whether equipment
will fit in the racks.
4 In your opinion or experience,

must rack-mounted devices fill
the depth of the rack and mount to
the back rails?
No. Light equipment or equipment that doesnt

need the full depth often does not extend to the
back rails. Rack-mounted equipment would
probably never extend further than the standard
depth.
PR
EV
IE
3 What are the advantages of

standardizing the U height?
16
Electrical and static safety

Explanation
Electricity can be dangerous. If you dont follow proper safety precautions, electricity
can kill you. Current, not voltage, is what causes the danger. Even a small amount of
current passing through your heart can be sufficient to cause ventricular fibrillation or
stop your heart entirely. A dangerous level of current is possible even with low voltage
sources, such as a 9 V battery.
The 1-10-100 rule
The 1-10-100 rule states that you can feel 1 mA (1 milliamp, or 1/1000 amp) of current
through your body; 10 mA is sufficient to make your muscles contract to the point
where you cant let go of a power source; and 100 mA is sufficient to stop your heart.
This is a rule you should learn and respect.
Safety precautions
IE
Some sources indicate

that 70 mA is sufficient
to cause death.
You should always follow common-sense safety precautions to avoid electric shock.
These precautions include the following:
Dont touch exposed electrical contacts with any part of your skin.
Touch only insulated handles and parts of tools, probes, cords, etc.
Leave covers on equipment unless you need to access their internal components.
EV
Work one-handed. If you use only one hand, electricity is less likely to flow
through your body (specifically, your heart or head) and cause injury or death.
Never insert anything into a wall outlet other than a power cord.
Remove jewelry and watches when working around electricity. Rings, watches,
and jewelry can cause unintended contact with electrified components.
Furthermore, these metallic items can increase the surface area thats in contact
with an electrical source and thus lower your bodys resistance.
Keep your hands clean and dry.
Dont work with electricity in wet surroundings, especially on wet floors.
Static electricity
PR
Static electricity is the buildup of an electrical charge on the surfaces of objects. Static
electricity can dissipate harmlessly to ground if a suitable path is provided. Often, static
is discharged quickly when objects having different electrical charges are brought into
contact or simply near enough to each other.
To feel a static shock, you must experience a discharge of approximately 3000 volts or
more. Discharges of more than roughly 8000 volts might generate a visible spark.
Walking across a carpet on a dry day can generate a charge of up to 35,000 volts. Yet
electronics can be damaged by a 1000-volt discharge or lessa third or less than the
minimum discharge you can feel.
17
To reduce the buildup of static charges and limit the likelihood of sudden discharges,
follow these tips:
Dont shuffle your feet as you walk.

Increase the humidity in the room or buildingstatic charges can dissipate
before growing large if the humidity level is sufficiently high.
Wear cotton clothing, which is less likely to generate static charges than are
many synthetic materials.
Remove carpeting from computer rooms and from rooms where you service
computers.
Use an air ionization system to build up an opposite, and thus neutralizing,
charge in the air.
Equalize charges safely. Unplug the equipment, and then touch a metal portion
of its chassis.
To prevent damaging discharge from occurring, you need to be at equal charge potential
with the device youre servicing (not at equal charge with ground). Do not leave the
computer plugged in while servicing it. If theres a fault in the buildings wiring system,
full wall current could be flowing through the ground wire. You could be injured or
killed if you came into contact with the ground.
PR
EV
You need to be at
equal potential with the
device youre
servicing, not with
ground.
Use the tools found in a typical ESD (electrostatic discharge) kit, such as wrist
straps and mats, to remain electrically connected to the devices youre servicing.
You and the components youre servicing do not need to be connected to
ground; in fact, that can be dangerous.
IE
Tell students
that while some guides
recommend leaving
the computer plugged
in, doing so is
dangerous and they
should not do that.
A-2:
Do it!
Opening the computer case while following proper

ESD precautions
Heres how
Students
computers should be
turned off.
Heres why
1 Disconnect the power cord from

the computer
2 Disconnect any other external
cables
3 Release the restraining
mechanismsscrews, slides, or
push-buttonsthat secure the side
that exposes the internal
components
For example, network cables.
IE
Before class, familiarize

yourself with the
classroom machines so
you can guide students in
this activity.
18
If you opened the side covering

the underside of the main circuit
board, open the other side
4 Touch the metal frame of the
computer and count slowly to
three
To discharge any static charges present on your

body or on the computer.
EV
Make sure students

have their computers
unplugged before they
perform this step.
5 Remove the front cover
Youll examine the internal components more in

upcoming topics.
PR
6 Leave the case open
19
Case features
Almost every PC case includes a basic complement of buttons and switches. These
include power buttons, reset buttons, and power or drive-activity lights. In addition,
modern cases sometimes include:
Chassis intrusion switches
Diagnostic LEDs
Explanation
Redundant power supplies

Expansion bays
Chassis intrusion switches
IE
Some computers include a switch that is triggered when you open the system case. In
some cases, triggering this switch prevents you from booting the PC (so that you cannot
boot it with the cover open). In other cases, the switch alerts you that the case has been
opened. With such cases, when you attempt to boot the PC later, you get an error and
must reset the switch in the BIOS before the computer will boot.
EV
Follow your manufacturers instructions to reset such switches. Often, unplugging the
computer and waiting a few seconds will be sufficient. Sometimes you will also need to
remove the CMOS battery (which backs up the BIOS configuration) and wait until your
BIOS is cleared. Motherboards that include support for chassis intrusion switches
sometimes include jumpers or switches you can use to disable them. Consult your
systems documentation.
Diagnostic LEDs
Many computers include diagnostic LEDs. These LEDs light up in colors and patterns
to indicate the operational state of the computer. For example, four green LEDs might
mean that all is well, while one yellow and three green LEDs might indicate failed
memory. The exact color and pattern sequences vary by manufacturer.
Sometimes the diagnostic LEDs are mounted on the motherboard. If they are, you must
either open the system case or view the LEDs through a ventilation hole or fan. Usually,
however, the LEDs are mounted outside the case.
Redundant power
PR
By some estimates, power-related equipment costs 2% of the price of a computer, yet

nearly 30% of computer problems are power related. If such figures are even close to
accurate, they argue strongly for spending more on high-quality power-related devices,
such as power supplies, UPSs, and proper wiring. One way to improve redundancy, and
thus lessen problems, is to use redundant power supplies.
Redundant power supplies are simply multiple power supplies in a single case. Each
power supply is capable of providing all of the power that the computer requires.
Special circuitry monitors the power output and switches to the backup power supply if
the primary one fails.
To take full advantage of such a configuration, you would want to plug each power
supply into its own UPS, and plug each UPS into its own electrical circuit. Ultimately,
each circuit would be backed up by its own generator. In such a configuration, failure
due to a power outage would be nearly unimaginable.
110

Expansion bays
In basic terms, an expansion bay is a space into which you can mount a disk drive or
other add-on device. Such a bay might just be a space with available mounting hardware
(brackets or screw holes) into which you add a drive. Or the bay might include power
and data connectors, plus slides or rails into which you insert custom drive enclosures.
For example, in the Hewlett-Packard media expansion bay, offered in some HP

computers, you can slip standard-size removable drives. The bay provides power and
data connectors, along with slides or rails that permit you to insert and remove the drive.
Laptop computers often include a similar media expansion bay. The CD/DVD drive
would mount in this slot. You often have the option to remove that optical drive and
insert a floppy disk or tape drive with such laptops. Such media expansion bays are
proprietary and specific to the manufacturer.
IE
In desktop cases, a bay is often just a place to install a drive. Depending on the case size
and style, the bay might be accessible from the outside of the case; youd use such bays
to mount optical drives or tape drives that you need to insert media in and remove media
from. Other bays are just internal; youd use these to mount spare hard drives.
PR
EV
Rack-mounted computers often include bays accessible through the front or top of the
case. You might slide out the rack PC, and lift the top of its case to access the bay. Such
bays enable you to quickly access and replace failed drives.

Do it!
A-3:
111
Examining your system case
Heres how
Heres why
1 Examine your computers case.

Locate the power switch and the
reset switch.
Almost all power switches use the circle-with-line

power symbol as defined by the IEC 60417
standard. Reset switches have less standardized
symbols if they are labeled at all.
Are there any indicator lights on

the front of the case, and if so, are
they labeled?
Common symbols include a light-bulb to label the

powered-on indicator, and a cylinder to label the
drive-activity indicator.
IE
Are these switches clearly

labeled?
2 Does your case include diagnostic

LEDs? If so, where are they
located? Is this a convenient
location for a technician?
EV
3 Does your case include externally

accessible expansion bays? If so,
are they the media bay type or
simply mounting locations for
devices?
4 Does your case provide redundant

power supplies?
Your case should be open from a previous

activity.
6 If your instructor has other

computers using a different case
style, such as a rack PC, examine
that case for these same
components
Look for diagnostic LEDs, expansion bays,

power supplies, and intrusion switches.
PR
5 Does your case include a chassis

intrusion switch?
112
Topic B: Power supplies
This topic covers the following CompTIA Server+ (2009 Edition) exam objectives.
#
Objective
1.2

Power
Connectors
Voltages
Phase
Differentiate between processor features/types, and given a scenario, select an appropriate

processor
VRMs
IE
1.5
Electricity background
Explanation
Electricity is the flow of electrons. A conductor is a material that permits the flow of
electricity. An insulator is a material that inhibits the flow of electricity.
EV
Voltage
Voltage is analogous
to water pressure.
Voltage is the force of electricity caused by a difference in charge, or electrical

potential, at two locations. This value, measured in volts, is also called the potential or
potential difference. The abbreviation for volts is officially an uppercase V, though a
lowercase v is commonly used.
Current
Current is a measure of the flow of electrons past a given pointessentially measuring

the speed of the electrons through the conductor. It is measured in amps, or amperes.
For current to flow, there must be a complete circuit, or path, from the source, through
any intervening devices, and back to ground. A complete circuit is called closed; an
incomplete circuit is called open.
PR
Alternating and direct current
Current that flows in a single direction at a constant voltage through a circuit is called
direct current (DC). Batteries provide this sort of current, and its the type required by
most electronic components.
Current that flows repeatedly back and forth through the circuit at a constantly varying
voltage level is called alternating current (AC). A buildings electrical service is an AC
system, and most household devices require AC to operate.
AC systems complete a full cyclevoltage change from zero, through maximum
voltage, minimum voltage, and back to zeromany times a second. In the United
States, Canada, and elsewhere, AC operates at 60 cycles per second (60 hertz, or Hz).
Europe and other countries use 50 Hz AC electricity.
113
Phase
In North America, most residential and small-business AC electricity is provided as

single-phase service over three wires. Such a system uses three conductors to deliver an
AC voltage on two conductors that vary in unison (though opposite in polarity), with the
third conductor acting as a ground connection.
Either 120 V electricity (between one hot conductor and ground) or 240 V electricity
(between two hot conductors) can be provided in a single service drop. Because of
this arrangement, this common service type is sometimes incorrectly called two-phase.
Single-phase electricity is suitable for lighting, for small motors, and when converted to
DC, for powering computers and office electronics. It is not efficient for high-powerneed devices, such as large motors. For those, power companies can provide three-phase
electricity service.
IE
In a three-phase system, three conductors are used (sometimes a fourth is included to

provide a ground connection). Each of the three conductors is hot, providing an AC
voltage. The peak of the AC signal in one conductor is delayed by 1/3 of a cycle from
the next conductor, which is delayed by 1/3 of a cycle from the next conductor. This
delay between signal peaks provides for a constant transfer of power over the entire
cycle.
EV
Three-phase power is more efficient for motors and other high-draw equipment. You
might encounter three-phase electricity on the factory floor or in utility areas of a large
commercial building, but not in a typical office setting. It is not compatible with office
equipment or computers. Three-phase devices use different plugs and sockets to prevent
you from accidentally plugging in a single-phase device.
PC power supplies
PR
A PC power supply, shown in Exhibit 1-3, is the internal component that converts wall
voltage (110 V or 220 V) to the various DC voltages used by the computers other
components. Power supplies have a fan to cool their components and sometimes to help
cool the other components inside the PC. Typically, a power supply provides some
conditioning functions and can maintain DC supplies during very brief drops in and
outages of supply voltage.
Exhibit 1-3: A PC power supply
114
IE
Often, you can adjust the power supply to run on either 110 V or 220 V wall voltage. To
make this adjustment, with the computer off, you slide a small switch to the appropriate
voltage. This switch is normally next to the electrical cord port on the back of the PC, as
shown in Exhibit 1-4.
Exhibit 1-4: A voltage selection switch near the electrical cord port
Power supply specifications
Power supplies are rated according to the number of watts of DC power they output.
Modern power supplies typically offer at least 300 watts, and often more, to power the
PC and its internal components. Older power supplies typically offered 200 watts or
less.
EV
The power supplys rating isnt necessarily an indicator of the amount of power that the
unit draws from the outlet; a 350 W power supply doesnt necessarily use more
electricity than a 200 W model. Power supplies draw only as much power as is needed
to supply the internal components. If your system needs less than the power supplys
full capability, the power supply draws enough electricity to power the PC, and no
more.
PR
The following table lists typical power requirements for common PC components. You
can usually find out an exact power requirement from technical specification documents
posted on manufacturers Web sites. Its often not possible, however, to separate
memory and CPU power requirements from the motherboards.
115
Typical power requirement
Motherboard
30 W, not including the power for the CPU chip and memory. This is for
full power mode. Sleeping states use less.
Memory
10 W per 2 GB chip.*
CPU chip
AMD Phenom processors use 65140 W; AMD Athlon 64 processors use

45125 W; single-core and dual-core Itanium processors use approximately
100 W; Pentium 4 and Athlon-class processors use 65 or more watts; older
CPUs use 50 W or less.
Hard drive
515 W. Some manufacturers will print the power requirement right on the
drive.
Optical drive
Newer CD or DVD drives can use as little as 5 W. Older optical drives may
require 1020 W.
Floppy drive
510 W.
Adapter card
530 W. For example, the high-end graphics cards used by professional

graphics software developers and computer-aided designers will require
more power than a normal graphics card.
IE
Component
EV
* BEHARDWARE.COM determined power consumption in a test system. They measured

power consumption at 2 GB and then at 4 GB, because they state that it really isnt possible to
load the memory independently of the processor; the difference is an estimate of memory
power consumption.
Standard outputs
Most power supplies provide three output voltage levels at various amperage ratings to
supply power to the internal components. The following table describes these voltage
levels and the typical devices that use them. (More devices draw power at the +12 V
level than at any of the other ranges.)
Amperage
Typical devices using this output
+3.3 V
14 A
AGP video cards; motherboards (this output level is not

produced by older, AT-class power supplies).
PR
Output
-5 V
0.3 A
ISA bus (AT bus) adapter cards.
+5 V
30 A
Motherboards; CD/DVD drives; hard drives; PCI adapter

cards; Pentium III and earlier processors.
+5 V
0.85 A
The soft power switch, which maintains the system in a

ready-to-start state.
-2 V
1A
Some older network adapters and serial ports.
+12 V
12 A
CD/DVD drives; hard drives; Pentium 4 and Athlon

processors; motherboards.
116
The voltage regulator module (VRM)
For newer AMD processors such as the Phenom and Athlon, overall current usage
limitation on the power supply doesnt exceed a combined system power output for the
+5 V and +3.3 V outputs.
The VRM provides the appropriate supply voltage to the processor. If designed
according to Intel specifications, a single VRM can supply various voltages to multiple
processors installed on the motherboard. The VRM senses the required power needed
by a processor by watching for the VID (voltage ID signal) sent during the power-on
self test.
Power connectors
IE
Standard connectors are used to connect the power supplys output to the various
devices. Separate standards exist for the following connectors:
Drive power connectors
Motherboard power connectors
Standards for drive power connectors
EV
Hard drives, CD and DVD drives, and floppy drives use power connectors that are
standardized in size and shape, as well as in the placement and voltage carried by the
wires connected through them. There are three common power connectors: the
peripheral, floppy, and serial ATA (SATA) power connectors.
The peripheral connector is sometimes called a Molex connector, after one of the
manufacturers of this style of connector. Peripheral connectors are typically used
to connect hard drives and CD or DVD drives to the power supply.
The floppy connector is a 4-pin Berg connector. The 4-pin Berg connector is
smaller than a Molex connector and is used to connect the floppy drive to the
computers power supply unit.
Serial ATA (SATA) drives use the third type of power connector.
PR
Peripheral, floppy, and serial ATA connectors are shown in Exhibit 1-5 and Exhibit 1-6.
Exhibit 1-5: A peripheral power (Molex) connector, left; and a floppy power (Berg)
connector, right
117
Exhibit 1-6: A serial ATA power connector
Wire color
Molex pin
numbers
Berg pin
numbers
SATA pin
numbers
Voltage
Yellow
13, 14, 15
+12 V
1 (optional)
7, 8, 9
+5 V
2 and 3
2 (optional) and 3
10, 11, 12
Ground
Red
Black
EV
Some newer Berg

connectors use only two
wires, omitting wires to
pins 1 and 2. Pins 13
arent connected on a
SATA connector.
IE
Due to their shapes, these connectors can be inserted into drives in only one orientation.
They are said to be keyed, which ensures that you connect the appropriate power
input wires to the correct point on the device.
Standards for motherboard power connectors

The motherboard and its components must get power from the power supply. The
motherboard is connected to the power supply with either one or two connectors.
Newer, single motherboard connectors are keyed; you cant insert them incorrectly
(unless you force-fit them backwards).
The older standard for motherboard power connectors is the two-connector system.
These older connectors werent keyed, so they could be inserted in either direction. Not
only could you connect one of the pair to the wrong motherboard connector, but you
could also connect the plugs backwards. Such a misconnection sometimes resulted in
damage to the motherboard.
PR
A single motherboard power connector is shown in Exhibit 1-7, and dual power
connectors are shown in Exhibit 1-8.
118
IE
Power
connector
EV
Exhibit 1-7: Single motherboard power connector
Exhibit 1-8: Dual power connectors on an older motherboard

The following table lists the wire colors and associated pin numbers for the 20-pin ATX
v1.0 single motherboard connector.
Pin numbers
DC voltage level
Orange
1, 2, 11
+3.3 V
Red
4, 6, 19, 20
+5 V
Black
3, 5, 7, 13, 15, 16, 17
Ground
Gray
+5 V
Purple
+5 V
Yellow
10
+12 V
Blue
12
-12 V
Green
14
+5 V (Power_Good signal)
White
18
-5 V
PR
Wire color
119
The following table lists the wire colors and associated pin numbers for the 24-pin ATX
v2.0 motherboard connector.
Pin numbers
Orange
1, 2, 12
Red
4, 6, 21, 22, 23
Black
3, 5, 7, 15, 17, 18, 19, 24
Ground
Gray
Power-Good signal
Purple
Yellow
10, 11
Brown
Green
+5 V
+5 V
+12 V
14
-12 V
13
+3.3 V
16
PS_ON#, which is an active low signal

that turns on all of the main power rails.
This signal should be held at +5 V.
20
Reserved
EV
No color
+3.3 V
IE
Blue
DC voltage level
Wire color
Form factors
PR
The form factor of a power supply refers to its size and shape. The form factor you use
must not only fit into the case you use; it must also fit in relation to the motherboard and
other components. The names of power-supply form factors match those given to
system cases, because together these components form a matched set.
B-1:
Do it!
Examining a power supply and connectors
Heres how
Students
computers should be
turned off and unplugged.
The covers should be off
the students PCs. If
theyre not, have students
remove the covers.
Heres why
1 Identify the power supply in your

computer
2 Identify your power supplys
rating and output voltages
3 Locate a peripheral power
connector and examine its shape
This information is normally listed on a label on

the power supply.
IE
4 Locate a floppy-drive power

connector and examine its shape
120
5 Determine whether your computer

has a SATA power connector
The power supplies in newer computers provide

these connectors. You can purchase adapters for
older power supplies.
6 Locate the motherboard power

connector
Answers will vary.
EV
Do you have a single or paired

power connector?
The yellow wire carries +12 V, the red carries +5

V, and the black is ground.
PR
7 With any of the connectors, what

is the purpose of the yellow wire?
The red wire? The black wire?
121
Topic C: Cooling systems
#
Objective
1.2

Cooling
Fans
Water cooled
Passive
Active
IE
Shroud
Ducts
Redundant cooling
Hot swappable
Ventilation
1.5

processor
EV
Heat dissipation (heat sinks, fans, liquid cooling)
CPU cooling
Explanation
CPUs and the other components in a computer are designed to operate within a range of
temperatures. Temperatures outside that range can damage components. In particular,
too much heat can cause logic errors, in which data within the chips and wires is altered,
or cause circuit damage, which can melt components!
The current crop of desktop CPUs (excluding the processor classes defined as energyefficient or low-power) can draw over 100 watts of power. The CPUs must dissipate the
heat from all that power.
PR
Intel specifies that for its Core2 Duo Desktop Processor E4300 processors, the internal
temperature of the computer case should not exceed 61.4C. To maintain that
temperature range, PC designers must include the following features to cool the case
and the processor itself:
Fans
Shrouds
Heat sinks and cooling fins
Heat pipes
Water pumps
Peltier coolers
122

Fans and air openings
To maintain allowable temperatures, hardware designers must devise a way to move

heat away from the components that generate it. In most situations, this means forcing
hot air out of the case to allow cool air to enter.
Older CPUs generated so little heat that a simple fan (typically part of the power
supply) and a few openings in the case were all it took to maintain permitted operating
temperatures. Modern CPUs (and other components) generate too much heat for such
simple thermal management designs.
IE
Modern cases include multiple openings through which air can flow. Some cases
include multiple fans, in addition to the power supply fan, to move air. Exhibit 1-9
shows a system case with both power supply and CPU fans.
Power supply fan
EV
CPU fan
Exhibit 1-9: A system case with power supply and CPU fans to improve air flow
Heat sinks and cooling fins
Fans arent sufficient to dissipate the heat from Pentium-class processors. These
processors require more high-tech thermal management methods.
The amount of heat that can leave a component is directly proportional to its surface
area. Big, hot things cool faster than small, hot things do. Additionally, some materials
transfer heat better than others.
PR
A heat sink is something that absorbs and transfers heat better than its surroundings. The
most common type of heat sink used with CPUs is a set of cooling fins. Fins increase
the surface area that can transfer heat away from the CPU. Hardware designers began
adding cooling fins to CPUs before the Pentium eraan example is shown in Exhibit 110.
Exhibit 1-10: Cooling fins on an older 80486DX2 CPU
123
The fins are normally connected directly to the die or to an integrated metal plate on the
CPU, depending on its packaging design. A thermal compoundbasically a glue that
transmits heat wellis used between the parts to improve heat flow. You might also
hear thermal compound referred to as thermal grease.
IE
A heat sink (such as a set of cooling fins) relies on convectionwarm air rises away
from the fins while cooler air flows in from below. At some point, however, heat cant
dissipate quickly enough on its own. Thermal engineers can add fans to the cooling fins
to forcibly improve convection, as shown in Exhibit 1-11.
EV
Exhibit 1-11: Cooling fins and a fan on a Pentium processor

Shrouds
A shroud is a plastic or metal conduit for cooling air. As shown in Exhibit 1-12, a
shroud directs air to or from the fan to the CPU (or other components that need
cooling). This helps cool the CPU more than a fan that simply blows air into the system
case does. Shrouds and external fans provide better cooling than a CPU-mounted fan
like the one shown in Exhibit 1-11.
PR
Shroud
Exhibit 1-12: A shroud directs cooling air to where it is needed most
124

Heat pipes
Heat sinks, fans, and shrouds can get only so large before they no longer fit in the case
or are too heavy for the components to which theyre attached. If more heat must be
dissipated, designers can turn to other techniques, such as heat pipes.
Heat pipes are small tubes, typically built into cooling fins, that are filled with a small
amount of fluid. Heat vaporizes the fluid, which expands and rises to another area of
the piping. There, heat is transferred away and condenses, flowing back toward the
CPU and heat source.
EV
IE
Shown here is the

underside of the cooling
unit. The CPU was
glued to the gray area
near the top-right corner
of the photo. Heat pipes
carried warmed air to
the cooling fins and fans
that expelled the heat
from the laptops case.
Exhibit 1-13: Heat pipes and fans from a laptop computer
Even though no pump is involved, heat pipes provide an effective way of moving heat
away from the CPU. Additionally, the heat can be moved farther away so that
convection can be more effective. Heat pipes also permit smaller and lighter fins.
Water pumps
PR
For systems that generate too much heat for fins and heat pipes to cool, designers can
turn to more exotic cooling systems. One such system is a pumped water system. Like
heat pipes, tubes carry water past the CPU to pick up heat. The heated water is
transported away from the CPU, often outside the computers case, where the excess
heat is removed.
Most water cooling systems use heat exchangers, essentially cooling fins, to radiate
away the heat collected in the liquid. Some people have been known to immerse the
tubing or exchangers in an ice bath to chill the liquid more, rather than relying on
convection with the outside air. Some systems, notably commercial units built into
assembled systems, use Peltier devices or refrigeration systems to cool the liquid before
it is recirculated.
125
Peltier coolers
Nearly all of the preceding cooling methods rely on some form of convection. Heat
moves from the hot CPU to the cooler surroundings. But what if the surroundings arent
cooler than the inside of the PCs case? Or what if the ambient temperatures arent cool
enough? Factory floors and some other environments can be very hot. Convective
cooling devices cant work in those situations.
A Peltier (pronounced PELT-ee-y) device is an electronic component that gets
colder when a voltage is applied. Peltier coolers for CPUs provide cooling when
convective methods wont work. A Peltier device can be connected directly to the CPU
or used in conjunction with a water pump. Devices that can drop the temperature of a
CPU by 70 C are available.
C-1:
Examining the cooling systems in your PC
IE
Do it!
Heres how
Heres why
1 Examine the system case. How

many fans does your PC have?
Answers will vary.
2 Does your PC have a cooling

grille or holes on the side or top?
If so, how does the presence of
these cooling mechanisms affect
where you place a PC in your
work area?
Answers will vary.
3 Youre servicing a computer for a

customer who has been
complaining of weird system
crashes and data loss. The
customers computer is piled high
with books and shoved in a
cramped space under a desk. It
also sits on a thick carpet. What
would you suggest?
Overheating could be causing problems for this

customer. You should remove anything on top or
beside the case that might inhibit airflow. Many
cases include grilles or openings at the bottom
that can be blocked by thick carpeting. You could
put a board or even some books under the case
to elevate it above the carpets fibers.
4 If necessary, open your PCs case
Make sure to follow proper electrical and ESD

safety precautions.
EV
You should never block or cover openings in the

case, or you could cause the system to overheat.
PR
Students
computers are turned off
and unplugged.
Cases might be open from

a previous activity.
5 Does your CPU have cooling

fins? A cooling fan? An exotic
cooling device, such as a water
cooler?
Answers will vary.
6 If your instructor has one

available, examine a CPU with its
cooling fins removed
To see the thermal compound that connects the

two components.
7 Of the cooling options listed

before this activity, which are
active and which are passive?
Peltier coolers and some types of water coolers

are active. The remainder are passive.
126
Area cooling
When cooling the CPU or system case is not sufficient, you must cool the cabinet in
which the computers are mounted or the room in which theyre located. Cooling options
include:
Room cooling
Explanation
Rack cooling
Row cooling
Temperature
Humidity
IE
Before considering cooling options, lets first be clear by whats involved with air
conditioning. Computers require greater control of air conditions than simply
temperature. You must manage:
Purity (filtration)
Room cooling
Air-conditioned computer rooms are a common feature of many office buildings. Such
rooms provide an ideal environment for heat-sensitive computer equipment. For small
installations, simply placing standard servers in an air-conditioned room is all that is
needed to provide sufficient cooling.
EV
Larger environments require specialized computer rooms, often built with raised floors
and dedicated HVAC (heating, ventilation, and air conditioning) systems. These
systems condition the ambient air, but also force conditioned air under the raised floor.
Perforated tiles permit the upward flow of cooled air into particular components or
racks that need extra cooling.
Room cooling relies on the air conditioning system to circulate enough air to prevent hot
spots: the system must pull out enough warm air and push in enough cool air to
thoroughly mix the air in the room. High-density computer racks often create more heat
than can be sufficiently removed and cooled by a room air conditioning system.
Rack cooling
PR
Rack cooling systems come in two forms. In the first, you place a standard rack in your
cooled computer room. Fans are mounted to the top or bottom of the rack to force
conditioned air from the room or beneath the floor to flow through the rack. Such units
ensure that a known volume of air is blown through the cabinet, rather than relying on
convection.
Usually, the rack uses multiple fans in case one fails. Additionally, you can usually
swap out fans without shutting off power to the computers and devices mounted in the
rack.
In the second form of rack cooling, all of the cooling components are provided within
the rack itself. Such cooled racks could be placed in either a cooled computer room or in
standard office space. These self-contained units create a conditioned, computer-room
environment within the rack.
Self-contained rack cooling units sometimes employ cooling systems based on water (or
another liquid). Chilled water circulates through tubing within the rack and picks up
heat from the computers mounted there. Then, that liquid passes through what are
essentially refrigerator or air conditioner coils to expel the excess heat outside the rack.
Air is also drawn in, filtered, and passed by equipment to further expel heat.
127
Row cooling
These self-contained cooling racks can be used to provide a measure of redundancy. If

your rooms air conditioning fails, the racks cooling unit will continue to provide the
necessary cooling.
Row cooling is, in some ways, rack cooling extended to an entire row of racks. A
dedicated cooling unit is located within the row of racks. This unit circulates cooled and
conditioned air to all of the racks in that row. Some such units simply force convection
and heat exchange with the computer rooms cooled environment. Other types of units
use chilled water, circulated among the racks in the row, to actively cool the racks
interiors.
Do it!
C-2:
IE
Multiple row chillers provide redundancy in case one unit fails. Many row chillers use
multiple fans and redundant refrigeration units, as well as hot-swappable components,
to provide reliable cooling.
Evaluating area cooling options
Heres how
Heres why
1 Which area cooling systems are in

use at your company?
Situations would typically involve the need for

cooling a small number of rack-mounted devices
when no cooled computer room is available, such
as in a field office or temporary location.
3 Which is more effective: room,

rack, or row cooling?
The correct answer depends on your needs and

the resources available.
4 Why might you need redundant

cooling?
Redundant cooling ensures that conditioned air is

supplied even if your primary air conditioning
system fails. This prevents computers from
overheating and shutting down (or being
damaged).
5 Describe a benefit of hotswappable fans in a rack.
If a fan fails, you can replace it without shutting

off the equipment in the rack and disconnecting
the rack from the buildings electrical supply.
PR
EV
2 Have you encountered a situation

in which a self-contained cooled
rack would be a suitable cooling
option? Describe it.
128
Unit summary: Deploying the chassis

In this topic, you learned that system cases come in a wide variety of sizes and shapes in
both standalone server and rack-mounted forms. You identified the characteristics of
these chassis styles and the common features they can offer.
Topic B
In this topic, you learned that power supplies provide conditioned power at appropriate
voltages to the components in the server. You learned about the various power supply
characteristics, form factors, and features.
Topic C
In this topic, you learned about the various cooling mechanisms available to remove
the heat generated by servers and related components. You examined cooling in both
the standalone and rack-mounted server configurations.
IE
Review questions
Topic A
1 How tall is a 2U rack mounted device?
Each U-height unit equals 1.75 inches, so a 2U device is 3.5" tall.
2 How wide is a 1U rack-mounted device?
The U-height of a device doesnt correlate to its width. Standard rack components designed for a
19" wide rack fit within the 17.75" distance between rails.
EV
3 Mounting holes in the rails in a standard computer rack are arranged in groups of
_______, with each group spanning a height of ______ inches.
three, 1.75 (one U height)
4 What is the purpose of a chassis intrusion switch?
A chassis intrusion switch cuts power to the computer so that you cannot operate it with the case
open. Sometimes, once thrown, these switches prevent you from booting the PC as a means to
warn you that the case was opened.
5 True or false? Diagnostic LEDs are typically located on the front of a tower PC
case.
False; theyre typically located on the back of the case.
6 On the front or top of the case, rack-mounted computers often include a(n)
_________ ________ that enables you to quickly swap or add a storage device.
PR
Expansion bay
7 True or false? Phase is a characteristic of DC power.

False. It is a characteristic of AC power.
8 PC power supplies are often categorized by the number of _______ of electrical

power they can provide.
watts
9 Which of the following are voltage levels used by typical internal PC components?
[Choose all that apply.]
A
12 V
+5 V
+3.3 V
D +2 V
129
10 What is the purpose of the VRM?

The voltage regulator module provides the appropriate voltage level to the processor, based on a
signal sent by the processor.
Molex
11 The peripheral power connector, also called the _______ connector, is often used to
connect hard drives and CD/DVD drives.
12 The yellow wire in a power connector carries ______ volt DC electricity.
+12
13 Which cooling system relies on small tubes filled with a small amount of fluid?
A Cooling fins
Heat pipes
IE
C Heat sinks
D Peltier coolers
14 Which cooling system uses an electronic component that gets colder when voltage
is applied?
A Cooling fins
B Heat pipes
EV
C Heat sinks
Peltier coolers
15 True or false? Passive cooling devices rely on convection or conduction to dissipate

excess heat.
True
16 The three area cooling options are _____, ______, and ______.
Room, rack, row
17 What is the purpose of a self-contained rack cooling unit?
PR
Such a cooled rack can be placed in any location where a cool environment is required, rather
than having to be located in a environmentally controlled computer room.
130
Independent practice activity

1 Using your browser, visit the Web site of a computer and components supplier, such
as www.cdw.com or www.newegg.com.
Dual- or quad-core processor

SATA hard drive support
Built-in Gigabit Ethernet
2 Determine a price for a system meeting these specifications:

Tower form factor
3 Compare that price to a system meeting the same or similar specifications but in a
rack-mount chassis (1U or 2U size).
IE
4 Is there a price premium for the rack-mounted server? If so, speculate why.
There is typically a price premium for rack-mounted PCs. Some of the price difference stems from
the additional engineering involved in fitting the components within the smaller dimensions of a
rack-size chassis. Rack-mount systems often include components, features, and conveniences
not always available in tower form factors. Some of the price difference is simply a premium
added to cover the extra value of a rack-mount form factor.
5 Visit a site such as www.racksolutions.com, www.kellsystems.com, or

www.rackmountsolutions.net to investigate the options available in racks and rack
accessories.
EV
6 Visit www.apcc.com and click Products in the main menu. Then click Cooling to
view APCs cooling products. Examine the room, row, and rack cooling products
this company offers. Examine the product details for at least one of them.
7 If you were designing the cooling needs of a small computer room that would house
fewer than six racks, which cooling system would you choose? Why?
Answers will vary but might include either a small room cooling system or a row cooling system.
PR
8 Close your browser.
21
Unit 2
Unit time: 45 minutes
Complete this unit, and youll know how to:
IE
A Describe the function and features of
CPUs, identify a CPU, and classify CPUs

according to their specifications.
B Describe CPU packaging options and
related slot and socket technologies.
C Describe motherboards, their components,
PR
EV
and form factors.
22
Topic A: Central processing units
#
Objective
1.5

processor
Multicore
Multiprocessor
Cache levels
Speed
IE
Stepping
Execute disable (XD) or not execute (NX)

Hyperthreading
VT or AMD-V
AMD vs. Intel (non-compatible CPUs)

Processor architecture (RISC, CISC)
EV
64 bit vs. 32 bit
Processors
The central processing unit (CPU), or processor, is the brains of your computer. Its
the chip that processes instructions, manipulates data, and controls the interactions of
the other circuits in your computer. A CPU is shown in Exhibit 2-1.
PR
Explanation
Exhibit 2-1: A CPU (a Pentium III)
Some people
erroneously call the
computer case and all
the components it
contains the CPU. The
terms system or
system unit should
be used instead.
A CPU has these components:

A control unit
One or more execution units

Registers
Older CPUs and processors, in even modern mini-computers and mainframe computers,
were built from multiple chips and components. CPUs contained on a single chip are
called microprocessors. Almost all CPUs in personal computers are microprocessors.
23
The control unit
Execution units
The control unit is responsible for managing the flow of a program. Its the component
that retrieves the next instruction to be acted upon or the data to be processed.
Execution units are responsible for the processing of instructions and data. Execution
units are built from the arithmetic logic unit (ALU) and the floating-point unit (FPU).
The ALU calculates and compares numbers. The ALU does most of the work of the
processor, but its best suited to working with operations that act on whole numbers (not
fractions).
IE
The FPU is designed specifically to work with real numbers (numbers with fractional
components, and very large, very small, or very precise numbers). Its faster and more
efficient at performing mathematical manipulations than the ALU is.
Older CPUs didnt include an FPU, though one was sometimes offered as a separate
add-on chip called a math co-processor. The Intel 80386 and some 80486 processors,
which predate the Pentium line of CPUs, didnt include an FPU. In these older CPUs,
the functions of an FPU were performed by the ALU, but at a slower pace.
Cores
EV
A processor can have one or more execution units. A single-core processor has one
execution unit. A core is an execution unit. A dual-core processor has two execution
units, a triple-core processor has three, and a quad-core processor has four.
In a single-core processor, the processor orders, executes, and then selectively stores
strings of instructions in its cache (called registers; one cache has multiple registers).
When the processor needs data outside its cache, it must retrieve the data from RAM
through the system bus or from a storage device, such as the hard disk. This process
slows down performance to the maximum speed of the bus, memory, or storage device.
This speed is slower than the actual speed of the processor itself. The situation is worse
when the processor must multitask. When multitasking, the processor switches back and
forth between sets of instructions and programs.
PR
In a multi-core processor, each core handles incoming strings of instruction

simultaneously. When one core is executing instructions, other cores can be accessing
the system bus or executing their own string of instructions. To utilize a multi-core
processor, the operating system must be able to recognize multi-threading, and the
software must have simultaneous multi-threading technology (SMT) written into its
code. SMT enables parallel multi-threading, meaning that multi-threaded instructions
are delivered to the cores in parallel. Without SMT, the software can recognize only one
core.
A multi-core processor is different from a multi-processor system. In a multi-core
processor, system resources are shared and all cores reside on the same chip. In a multiprocessor system, there are two separate processors, each with its own system resources.
All other components being equal, a multi-processor system is faster than a system with
a multi-core processor.
24

Registers
Registers are very small, yet very fast, memory locations for holding instructions or
units of data. Registers operate at the same speed as the CPU, whereas normal system
memory can be many times slower.
During their operations, CPUs store data and instructions in registers. That information
is then transferred back to main system memory. To speed operations, the control unit
can prefetch instructions and data from system memory and store it in the CPUs
registers.
IE
CPUs can have many registers, with groups of registers devoted to a specific purpose
(and thus unavailable for other uses). Some modern processors can use registers as
needed for the task at hand, rather than being limited by a limited quantity of specialpurpose registers.
CPU performance
An instruction is the low-level, hardware-specific command to be acted upon by a

processor. It might be something like SUM 5, 10 to add 5 and 10. Before this
instruction can be executed, a previous instruction must have fetched the value 5 from a
location in memory and stored it in a register. Another must have fetched 10 from
memory. One more instruction is required to write the resulting sum back into a register,
from where it is transferred by the control unit to a new memory location.
EV
You can determine the performance of a processor by examining the number of

instructions it can perform in a second. With microprocessors, this amount is usually
rated in millions of instructions per second (MIPS).
CPUs used to be rated according to their clock speed. In a PC, the clock circuit keeps
the CPU and other chips synchronized so that they can work together.
Older CPUs took more than one clock cycle to perform a single instruction. Modern
processors perform many instructions in a single cycle. In fact, the clock speed is no
longer a good indicator of the performance of a modern CPU. By using the techniques
listed in the following table, a modern CPU can perform more than one instruction per
clock cycle and even perform multiple instructions at the same time.
PR
Ultimately, many factors control the actual speed (performance) of a CPU. The
following table describes some of these factors.

Relation to CPU performance
Addressable
RAM
The total amount of memory thats accessible to the processor.
Branch
prediction
A technique by which the processor anticipates the code that will be used next and
loads that code to try to get ahead of the program. When the processor guesses
correctly, the program speeds up. Otherwise, performance slows while the correct
instruction is retrieved.
Bus, address
The bus (pathway) that connects the processor to main memory. The wider the
address bus, the more memory can be accessed. Data isnt transferred over this bus.
Bus, data
The number of bits of data or instructions that can be transferred in a single

operation. The larger the data bus, the more data that can be moved and thus the
faster the processor can operate.
IE
Design
Bus, internal
The bus that determines how many bits of information the processor can work with at
once. If the internal bus is smaller than the data bus, data and instructions must be
manipulated in parts. For example, a processor with a 32-bit internal bus and a 64-bit
data bus must deal with data in two halves.
Cache
High-speed memory contained within or directly coupled to the processor. Accessing

data from cache is considerably faster than accessing it from main memory.
Processors use levels 1, 2, and 3 caching, where Level 1 cache is the fastest and most
closely coupled to the processor, Level 2 less so, and Level 3 even less (yet still
much faster than normal system memory). Processors save instructions, the data to be
processed, and the results in the caches.
EV
These are listed in

alphabetical order, not in
order of their
contribution to
performance.
25
The number of cycles per second of the computers synchronization clock, measured
in hertz (Hz), millions of cycles per second (megahertz or MHz), or billions of cycles
per second (gigahertz or GHz). A modern processor performs more than one
instruction during every clock cycle. Older processors performed one or fewer.
Normally, a clock speed rating refers to the internal or core speed of the processor,
rather than to the actual speed of the computers synchronizing clock chip.
Clock multiplier
Measures the ratio of internal bus speed to external bus speed in a CPU. For example,
consider a system with a 133 MHz clock speed and a CPU with a 10x clock
multiplier. Internally, the CPUs bus runs at 1.33 GHz (1,333 MHz) while externally
its bus runs at the systems clock speed (133 MHz).
Dual
Independent
Bus (DIB)
A processor architecture that includes two buses: one to the main system memory,
and another to the Level 2 cache. The processor can access both buses
simultaneously for improved performance.
Front-side bus
speed
The speed at which the processor interacts with the rest of the system. A processors
internal core speed can be many times higher than its front-side bus speed (see clock
multiplier). If the core speed is too much higher than the front-side bus speed, the
processor can sit idle, waiting for data to be moved in or out and made available for
processing.
Hyperthreading
An Intel technology that enables a single processor to execute two streams of

instructions at the same time, as if it were two processors.
Multimedia
extensions
(MMX)
An expanded set of instructions supported by a processor that provides multimediaspecific functions. Without MMX, a programmer might have to implement multiple
low-level commands to perform a multimedia operation. With MMX, the same
function would involve a single instruction.
Multiprocessing
The use of more than one processor within a system to speed program execution.
Operating systems and applications need to be written to support multiprocessing, or
no speed benefits are realized.
PR
Clock speed

Relation to CPU performance
Out-of-order
completion
A technique by which instructions can be executed out of order when order isnt
important and the processor determines a more efficient sequence.
Overclocking
Running the CPU at a higher speed than it was rated to run at. Overclocking
increases performance, but also increases the potential for errors. Also, more heat is
generated by an overclocked CPU.
Pipelining
The overlapping of the steps involved in processing instructions. Instructions are

normally fetched, decoded, and executed, and the results are written out to memory.
Modern processors overlap these steps to speed overall execution. While one
instruction is being executed, another is being decoded, and a third is being fetched.
Register
renaming
A technique by which modern processors can rename registers so that instructions

can access their own set of registers and not interfere with other instructions. When
multiple instructions are running at the same time, theres a chance that two will
attempt to read or write to the same register simultaneously. Register renaming
prevents this.
RISC vs. CISC
Reduced Instruction Set Computer (RISC) vs. Complex Instruction Set Computer
(CISC). RISC is a CPU design philosophy that holds that performance will be
improved if the features of the CPU are reduced, forcing advanced features to be
provided through software. CISC holds the opposite: hardware is generally faster, so
a more complex CPU will outperform a reduced-instruction-set CPU.
Design
IE
26
EV
RISC CPUs include the PowerPC, Alpha, and ARM architectures. CISC CPUs
includes the x86 family from Intel and AMD. In general, CISC has won in the
marketplace, though thats not necessarily an endorsement that CISC is somehow
better than RISC.
A technique by which a single instruction can be applied to more than one piece of
data. For example, with SIMD, five numbers might be moved into the processor
along with the single command to add them up in one operation. The next operation
would carry out that instruction. Without SIMD, the numbers would be added
together one by one in a longer sequence of instructions.
Speculative
execution
A technique by which a processor executes an instruction in the expectation that the

result is needed. This technique can improve performance when the program
branches, as in an if this condition is met, do that operation situation. The
processor can begin performing the operation before the condition is fully evaluated,
in the expectation that it will be met.
Superpipelining
An improvement over pipelining. Superpipelining uses a larger number of shorter

stages and support for a higher clock rate to improve performance.
PR
Single
Instruction
Multiple Data
(SIMD)
Superscalar
A technique that enables a processor to execute more than one instruction in a single
clock cycle.
Throttling
A technique by which the speed of the processor is scaled back so that it uses less
power and creates less heat. Throttling reduces performance. Its most useful with
portable computers, for which low power consumption and low heat production are
critical design factors.
27
Support for multiple processors
Some computers come with two processors. However, in order to take advantage of the
increased performance gained with two processors, the operating system and
applications you run must include symmetric multiprocessing code. Windows Server,
Windows 2000 Professional, Windows XP Professional, and Windows Vista Business,
Ultimate, and Enterprise include symmetric multiprocessing code. Windows XP Home
and Media Center Editions and Windows Vista Home and Home Premium dont. You
can get the Linux operating system in symmetric multiprocessing versions.
Virtualization support
IE
Virtualization is a technology through which one or more simulated computers run

within a physical computer. The physical computer is called the host, and its operating
system is the host OS. The simulated computers are called virtual machines (VMs), and
their operating systems are called guest OSs.
EV
Virtualization offers a range of benefits and is a suitable solution largely because many
user and system functions typically consume far less than the full power of a modern
computer. For example, if a users activities on her PC use just 30% of the computers
capabilities, 70% is being wasted. Through virtualization, potentially three VMs could
be run on a single system at this level of utilization, giving similar performance levels.
Exhibit 2-2: Multiple VMs on a single physical host
PR
Early virtualization products required modifications to the guest OS, particularly

hardware drivers. Some modern CPUs include virtualization support features that
enable the host to run unmodified guest operating systems. Intels Virtualization
Technology (VT or VT-x, which stands for Virtualization Technology for x86) and
AMDs AMD-V (the V stands for virtualization) are the primary examples of CPU
virtualization features.
Intel VT and AMD-V are not compatible, though they provide essentially the same
features. Current host OS options typically support both of these virtualization
technologies. Citrix XenServer and Microsofts Hyper-V are examples of host operating
systems (or operating system components) that take advantage of CPU virtualization
features and enable virtualization.
At the time of this writing, you could visit http://en.wikipedia.org/wiki/
X86_virtualization#Hardware_support to obtain a partial list of Intel and AMD
processors offering hardware virtualization support. Check the manufacturers
specification sheets for authoritative information before selecting a CPU for your
system.
28
Memory protection
Another feature of modern CPUs is generically called no execute, or NX. This feature
enables the CPU to mark a section of memory as non-executable: any code stored within
that area of memory will not be run. NX is called Execute Disable (XD) by Intel and
Enhanced Virus Protection by AMD.
In theory at least, executable program code is supposed to be stored separately from
data in memory. This separation is supposed to prevent malicious program code,
embedded within data, from running on your computer. In practice, this segregation has
not been strictly enforced, leading to buffer overflow attacks, in which virus writers
overfill an area of data storage, eventually placing executable code within your
computers memory. Then they execute that code to take control of your PC.
IE
NX on the Intel platform was first provided through software, starting with
enhancements added to Windows XP Service Pack 2. Since then, CPU makers have
added NX support directly to the CPUs. By placing this support into hardware, they
make it more difficult for virus authors to circumvent the no-execute protections than if
the feature were provided through software.
AMD was the first manufacturer to add NX support to its CPUs, beginning with the
Athlon 64 and Opteron processors. Intel followed, adding support to Pentium CPUs
based on the Prescott core. In general, all current processors from AMD, Intel, and VIA
support the NX technology.
EV
CPU versioning
Each CPU maker uses its own version numbering scheme, making it difficult to keep
track of and compare processors across lines. However, in general, all of the
manufacturers divide their CPUs in this fashion:
Brand
Model number
Stepping
Brand
PR
A brand, or family, of CPUs is the name you see advertised, such as Intel Core2
Duo or AMD Phenom. Each of these families comprise many specific models of
CPUs, each with varying characteristics and capabilities.
Model number
The model number describes a specific line of CPUs within a family. For example, the
P7000 model number describes a set of CPUs within the Core2 family by Intel. Model
numbers can be more specific. For example, P7350 and P7370 are CPU lines within the
larger P7000 line of Intel CPUs.
Higher model numbers generally imply better performance, though not all specifications
might be better. For example, a higher-numbered CPU might have a faster front-side
bus but a lesser Level 2 cache than a lower-numbered CPU.
Model numbers might begin with a letter prefix or end with a letter suffix. For example,
the Intel E8500 and Q9550S are processors in the Intel Core2 family. Each
manufacturer assigns its own meaning to these letters. See the manufacturers Web sites
for complete details.
For information
on Intels use of
prefixes and suffixes,
see www.intel.com/
products/
processor_number/
about/core.htm.
29
Stepping
The stepping is a version indicator within a processor line. Steppings are combinations
of letters and numbers, such as A0. A change in the number, such as to A1, indicates a
minor design change. A change in the letter indicates a more substantial change, such as
changes in cache size, power consumption modes, and so forth.
IE
CPU makers rarely print the stepping on the CPU. Instead, they print an sSpec number.
For example, you would see SLAEB printed on the CPU for the M0 stepping of the
Core2 Duo T5470 CPU.
Its important to note that a higher stepping value does not automatically mean
improved performance or features. A higher stepping number might indicate a CPU
with reduced cache size, for example, meant to reduce production (and thus retail) costs.
It might also indicate a change made in the processor design to fix a bug or make
manufacturing easier.
Do it!
A-1:
Identifying CPUs
Heres why
EV
Heres how
Students
computers should be
turned off.
1 Disconnect the power cord from

the computer
2 Disconnect any other external
cables
For example, network cables.
3 Release the restraining

mechanismsscrews, slides, or
push-buttonsthat secure the side
that exposes the internal
components
4 Touch the metal frame of the
computer and count slowly to
three
To discharge any static charges present on your

body or on the computer.
5 Remove the cover
So you can view the motherboard and processor.
6 Locate your CPU
Modern CPUs typically have a set of cooling

fins glued to them, covering all markings. This
will prevent you from identifying the CPU or its
specifications.
PR
Make sure students

have their computers
unplugged before they
perform this step.
210

7 If the CPUs label is visible,
record the manufacturer and
model of the CPU
Your instructor might be able provide you with

this information if it is not visible on the CPU.
Manufacturer: ___________________________
Brand (family): _________________________

Model number: _________________________
Stepping or sSpec: _______________________
8 Close your system case and

assemble your PC
9 Boot your PC
The is a continuation
character.
IE
Log on as Administrator with

a password of !pass1234
10 Open your browser and visit
http://en.wikipedia.org/wiki/
X86_virtualization#Hardware_support
Answers will vary.
EV
11 Is your CPU listed among those

supporting AMD-V or Intel VT-x
support?
If your CPU is not listed, visit the
Intel or AMD Web site, as
appropriate. Using the published
specifications on the site,
determine if your CPU supports
virtualization features.
Intel: www.intel.com
AMD: www.amd.com
Determine if your CPU supports

the NX (no execute) feature.
12 Visit www.digital-daily.com/cpu
13 Compare one of the AMD
processors with one of the Intel
processors; which do you think is
the more powerful CPU, and
why?
You need to consider many factors, including

clock speed, front-side bus speed, and Levels 1
and 2 cache.
14 Which processors do you or your

company use?
Answers will vary, but Intel is likely to be the most

common answer.
PR
If students are asked

whether to turn on the
phishing filter, have them
choose Yes, then click
OK.
211
Topic B: Packaging and slots

#
Objective
1.5

processor
Vendor slot types
CPU packaging
Any type of microchip is made up of microscopic wires, transistors, and other

components. This plain chip is called the die. To be useful, it must be connected to the
rest of the circuitry of the computer. Due to the size differences between the wires on
the die and the circuit boards in the computer, the die cant be connected directly to the
circuit board.
IE
Explanation
This topic covers the following CompTIA Server+ (2009 Edition) exam objective.
EV
Instead, the die is built into a package. A package is a case made from plastic, ceramic,
glass, metal, or some other material, plus the wires and connectors that bridge the
microscopic connections on the die with the external circuitry. A package might also
include support function chips, memory, and cooling-related components.
Exhibit 2-3: A PDIP (plastic dual inline package) memory chip
PR
Older package types, such as the PDIP pictured in Exhibit 2-3, used connectors that
were large compared to the die. Newer packages use ever smaller connectors, packing
more connections into a smaller area. The pin grid array (PGA) package, shown in
Exhibit 2-4, includes many more connections in an area not much larger than the die.
The overhead shows the

top and bottom sides of
the 80486DX2 CPU.
Exhibit 2-4: The underside of an 80486DX2 CPU, showing the pins of its pin grid array
package
212
Even though newer packages use smaller connectors, overall package size has grown as
functionality has grown. Newer packages include support chips, cache memory, and
features that enhance the cooling of the processor. One such larger package is shown in
Exhibit 2-5.
IE
The overhead shows

two views of the Pentium
3 Single Edge Contact
Cartridge package.
Exhibit 2-5: The Single Edge Contact Cartridge package

CPU packages
The following table lists some current and historical CPU packages used in desktop
computers. Manufacturers can vary these with updated lines, so be sure to check the
technical specifications for your particular CPU on the manufacturers Web site.
Full
name
Description
EV
Package
Processors
Plastic dual
inline
package
The die is encased in plastic (or another

material). Large, flat, metal pins are inserted
into a socket thats soldered to the motherboard.
8080, 8086, 8088
PGA
Pin grid
array
Rows of pins extend from the bottom of the

package. A nickel-plated copper slug sits atop
the die to improve thermal conductivity. The
pins are arranged so that the chip can be
inserted in just one way.
80286 (68 pins), 80386

(132 pins), 80486 (168),
and Xeon (603 pins)
CPGA
Ceramic pin
grid array
A package that uses a ceramic substrate with

pins arranged in a pin grid array.
AMD Socket A Athlons

and the Duron
SPGA
Staggered
pin grid
array
Similar to PGA, but pins are staggered to fit

more pins in a given area.
Pentium, Pentium
MMX, and Pentium Pro
with 387 pins
PPGA
Plastic pin
grid array
An updated version of the SPGA package.
Pentium Pro, early

Celeron processors, and
Pentium III with 370
pins
FC-PGA
Flip chip pin

grid array
Similar to PGA, but the die is exposed on top.

This design enhances heat transfer and cooling
options.
Pentium III and Celeron

with 370 pins; the 423pin version is used with
Pentium 4 processors
PR
PDIP
213
Full
name
Description
Processors
FC-PGA2
Flip chip pin

grid array 2
Similar to FC-PGA, but with an integrated heat

sink, which is connected to the die during
manufacturing.
Pentium III and Celeron

with 370 pins; the 478pin version is used with
Pentium 4 processors;
the 469-pin version is
used with AMD Athlon
Thunderbird processors
OOI
OLGA On
Interpreter
The die is mounted face down for better

cooling, as with the FC-PGA package, but uses
a different pin arrangement.
423-pin Pentium 4
OPGA
Organic pin
grid array
The silicon die is attached to an organic plastic

plate (fiberglass), which is pierced by an array
of pins to make the connections to the socket.
This package is cheaper, thinner, and lighter
than the ceramic package. It also reduces
electrical impedance.
AMD Athlon XP
Single Edge
Contact
Cartridge
Rather than mounting horizontally, this package

mounts the CPU vertically on the motherboard.
Rather than pins, this package uses an edge
connector similar to an adapter cards. The die
is covered with a metal case. A metal thermal
plate mounted to the back of the cartridge acts
as a heat sink.
Pentium II processors
with 242 contacts, and
Pentium II Xeon and
Pentium III Xeon
processors with 330
contacts
IE
EV
SECC
Package
Single Edge
Contact
Cartridge 2
Similar to SECC, but without the thermal plate.
Later versions of the

Pentium II and Pentium
III processor with 242
contacts; AMD Athlon
K7
SEP
Single Edge
Processor
Similar to SECC, but without the metal case.
Early Celeron
processors with 242
contacts
FCBGA
Flip chip
ball grid
array
Similar to FC-PGA, but uses balls rather than

pins for contacts. The balls cant be bent as the
pins can.
Xeon, plus many

support chips in current
Pentium-class
computers
LGA
Land grid
array
Has small raised contacts instead of pins. The

corresponding socket has pins that meet the
contacts. This is a very high-density package.
Celeron D, Pentium 4,
Pentium 4 D, Pentium
Extreme Edition,
Core2 Duo,
Core2 Extreme
PR
SECC2
214
Sockets and slots
The processor packages listed in the preceding table must be inserted into a socket or
slot on the motherboard. The following table lists common desktop computer sockets
and slots. (As with packages, manufacturers can vary sockets and slots with updated
lines, so check the technical specifications for your CPU on the manufacturers Web
site.) A desktop processor and its associated socket are shown in Exhibit 2-6.
Supports these
packages
Processors
Notes
Slot A
AMDs Card Module

package
AMD Athlon
This wasnt a popular design and

didnt last long on the market.
Socket A
(also called
Socket 462)
SPGA with 462 pins
AMD Athlon and Duron
Eleven holes in this socket were

plugged to ensure that packages
were installed correctly.
Socket 5
PGA, SPGA with

320 pins
Pentium
Socket 7
PGA, SPGA with

321 pins, and PGA,
SPGA, and FC-PGA
with 296 pins
AMD K5 and K6,

Cyrix 6x86, Pentium,
and Pentium MMX
IE
Type
EV
First socket to support dual voltage

inputs, which support the various
core and I/O voltages introduced
with the Pentium MMX
processors. Socket 7 has one more
holes than Socket 5 but isnt
electrically connected. It simply
prevents a new CPU from being
plugged into a Socket 5 socket.
387-pin PGA, SPGA,

and FC-PGA
Pentium Pro
A short-lived socket design used

primarily with the Pentium Pro.
Socket 423
423-pin SPGA and

FC-PGA, OOI
Pentium 4
A short-lived socket design used

for early Pentium 4 processors.
Socket 478
FC-PGA2
Celeron, Pentium 4,
Pentium D, and Pentium
Extreme Edition
The current general-purpose socket

for Pentium-class processors.
Socket 370
SPGA and PPGA

with 370 pins
Celeron, Celeron II,

Pentium III
Similar to the Socket 7 design,

with six staggered rows of pins
rather than five.
PR
Socket 8
Slot 1
SECC, SECC2, SEP

with 242 contacts
Pentium II, early

Celeron, and Pentium III
Edge connector slot developed

specifically for the SECC, SECC2,
and SEP packages.
Slot 2
SECC, SECC2, SEP

with 330 contacts
Pentium II and Xeon
Similar to Slot 1, but the CPU can

communicate with the Level 2
cache at full CPU speed, rather
than at the half-speed supported
through Slot 1.
LGA775
(also called
Socket T)
LGA
Celeron D, Pentium 4,
Pentium D, Pentium
Extreme Edition, Core2
Duo, and Core2 Duo
Extreme
Designed to work specifically with

the new high-density LGA
package. This is Intels current
high-end socket.
215
Do it!
B-1:
IE
Exhibit 2-6: A Pentium with an MMX CPU atop its associated Socket 7 socket
Identifying your CPUs socket and package type
Heres how
1 Shut down and unplug your PC
If necessary.
2 If necessary, open your system

case
Make sure to follow proper electrical safety and

ESD precautions.
EV
Make sure
students computers are
turned off and unplugged.
Heres why
3 Examine your CPU, and record

the socket and package type
Package: ________________
4 Identify the chipset chip on your

motherboard
Its typically a very large chip placed near the

CPU socket.
PR
Socket: _________________
216
Topic C: Motherboards
#
Objective
1.1
Differentiate between system board types, features, components, and their purposes
Dip switches / jumpers
Processor (single and multi)
Onboard components
HID
Video
Serial
Audio
Parallel
USB
IE
NICs
Riser card / backplane

1.5

processor
EV
VRMs
Motherboards
Explanation
The motherboard is the main circuit board in a personal computer. Its made up of
various components, including the CPU and other electronic devices, wires, and adapter
sockets into which additional circuit boards and devices can be attached. Exhibit 2-7
shows a motherboard with some of its primary components labeled.
PR
Expansion slots
Ports and connectors
CPU slot
Memory slots
Drive connectors
Exhibit 2-7: A motherboard
217
The following table describes the functions of various motherboard components.

Function
CPU
The chip that processes instructions, manipulates data, and controls the
interactions of the other circuits in the computer. Some servers and highpowered computers support multiple processors on a single motherboard.
Expansion slots
Slots into which you can plug additional circuit boards to expand the capabilities
of the computer.
Graphics adapter slot
A slot into which you can plug a graphics adapter card, which produces the
output displayed on your monitor.
Hard drive interface

connectors
Slots into which you can plug cables to connect hard drives, CD drives, and
DVD drives to the system.
IE
Component
A slot into which you can plug the cable to connect a floppy drive to the system.
Power connector
The connector to which you connect the output of the power supply to provide
electrical power to the motherboard. Older systems have a pair of slots rather
than a single connector.
Memory slots
Slots into which you insert memory modules to add system memory to the PC.
PS/2 mouse and

keyboard ports
Ports into which you can plug PS/2-style keyboard and mouse cables.
EV
Floppy drive interface

connector
One or more ports into which you can plug cables to connect USB devices to the
PC.
HID port
Human Interface Device port; a port to which you connect input/output devices,
such as keyboards, mice, and joysticks. Most often, simply a USB port.
IEEE 1394/FireWire
port
One or more ports into which you can plug cables to connect FireWire devices
to the PC.
Serial port
One or more ports into which you can plug cables to connect serial devices, such
as modems or mice, to the PC.
Parallel port
One or more ports into which you can plug cables to connect parallel devices,
such as printers, to the PC.
Battery
A battery to provide power for maintaining system configuration information

while the PC is turned off or disconnected from the outlet.
Network interface
Network interface circuitry built into the motherboard to enable connections to a

network without using an add-on adapter card.
Video connector
Video circuitry built into the motherboard, which provides a video connector on
the back of the system case.
Voltage regulator
module
A module that provides the appropriate supply voltage to the processor. If its
designed according to Intel specifications, a single VRM can supply various
voltages to multiple processors installed on the motherboard. The VRM senses
the required power needed by a processor by watching for the VID (voltage ID
signal) sent during the power-on self test.
PR
USB port
218

The motherboard is sometimes called the system board or main board. However, the
latter term is typically used to describe the main circuit board in non-PC devices, such
as alarm systems, televisions, and so forth.
Daughter boards
A daughter board is a circuit board that connects to a circuit board (sometimes, though
not normally, a motherboard) to provide or assist with its functions. Daughter boards are
often used with video cards to add more video-processing capabilities.
Riser cards
PR
EV
IE
As shown in Exhibit 2-8, a riser card is a circuit board that connects to a motherboard.
Unlike a daughter board, the purpose of a riser card is to provide additional expansion
slots or sockets. Riser cards are most often used with special, small motherboards
designed for small cases. Riser cards attach to a backplane, which is a set of connectors
in parallel served by a single bus.
Exhibit 2-8: An NLX-style motherboard (top) with its associated riser card, containing
the systems expansion slots (bottom)
Form factor
The form factor of a motherboard is its size and shape. In addition, the form factor
determines the power supply and case that can be used with a motherboard, along with
the general physical layout of the components on the motherboard. Of course,
motherboards must fit into cases, which means that screw holes or retaining-clip
locations must match between motherboards and cases. Standard dimensions and
mounting layouts help ensure that components work together.
219
The following table lists the common PC motherboard form factors. Other form factors
are available. Be sure to check the manufacturers specification documents for your PC
when choosing a replacement motherboard.
Dimensions
(inches)
XT
8.5 by 11
AT
12 by 1113
Some standards permit

a range of sizes.
Baby-AT
8.5 by 1013
ATX
9.6 by 12
Mini-ATX
Notes
Form
factor
Obsolete, used with IBM XT-class computers.
Obsolete, used with IBM AT-class computers.

A smaller version of the AT form factor.
Standard created by Intel in 1996 and still one of the most popular
form factors.
IE
It isnt necessary to go
over each of the form
factors in class. Refer
students to this table for
review.
8.2 by 11.2
Micro-ATX
9.6 by 9.6
Released in 1996. Offered fewer slots than the ATX form, so a

smaller power supply could be used in PCs with this motherboard
design.
LPX
9 by 1113
Designed for slimline PCs.
89 by 1011
Designed for slimline PCs.
89 by 1013.6
Standard created by Intel in 1999; this form factor requires a riser

card for add-on adapters.
Mini-LPX
EV
NLX
9.6 by 9.6
Mini-ITX
6.7 by 6.7
Standard created by VIA Technologies in 2003.
Nano-ITX
4.7 by 4.7
Standard created by VIA Technologies in 2004.
BTX
10.5 by 12.8
Standard created by Intel in 2004. Intel plans for this to be the

standard motherboard form factor for the future.
MicroBTX
10.4 by 10.5
A variation of the BTX form factor. Its different dimensions

notwithstanding, the MicroBTX shares the electrical and
component design with the BTX form factor.
PicoBTX
8.0 by 10.5
A smaller variation of the BTX standard.
PR
FlexATX
C-1:
Do it!
Examining motherboard components and form

factors
Heres how
Students
computers are turned off
and unplugged.
Heres why
1 If necessary, open your

computers case
2 Examine your motherboard
What form factor is your
motherboard?
Make sure to follow proper electrical and ESD

safety precautions.
Answers will vary.
IE
3 If your instructor has

motherboards with other form
factors, compare their size and
component layout with your
motherboard
220
4 Identify each of the following

items on your motherboard:
CPU and its socket

Memory slots
Bus (expansion) slots
I/O ports (serial, parallel, mouse, and keyboard)
EV
Integrated drive controller slots, if applicable

USB and FireWire ports, if applicable
Integrated video port, if applicable
5 Close your system case and

assemble your PC
6 Boot your PC
Log on to Windows Server 2008

as Administrator with a
password of !pass1234
7 Open your browser and visit
PR
Tell students to install the

Flash player, if asked.
www.motherboards.org
8 On the left, under Compare

Prices, click Motherboards
9 Examine the list of motherboards
available for sale
10 Whats the most popular

motherboard form factor for sale?
At the time of this writing, the ATX style seemed

to be the most common form factor for sale.
221
Unit summary: Selecting CPUs and

motherboards
In this topic, you learned that CPUs are the chips that process instructions, manipulate
data, and control the interaction of other PC components. You examined the
characteristics of popular CPUs, as well as the features that determine a CPUs
performance characteristics.
Topic B
In this topic, you examined the various CPU packages and the corresponding slots and
sockets into which theyre inserted.
Topic C
In this topic, you learned that the motherboard is the primary circuit board in a
personal computer. You also learned that motherboards come in specific sizes and
shapes that describe their form factor.
IE
Topic A
Review questions
1 Which of the following is not a component of a CPU?

A
Bus architecture
B Control unit
C Execution unit
EV
D Register
2 The math co-processor was the predecessor of which CPU component?

A ACL
B Core
FPU
D Register
3 A single-core processor has one of what component?

A Control unit
Execution unit
PR
C FPU
D Register
4 ______________ are very small, very fast, memory locations for holding
instructions or units of data.
Registers
222

5 Which type of bus connects the processor to the main memory?
A
Address bus
B Data bus
C Internal bus
D Generic bus
6 Which processor caching level is the fastest for accessing data?

A
Level 1
B Level 2
C Level 3
IE
D All are equal
7 Which of the following performance features can overheat the processor?

A Multiprocessing
B
Overclocking
C Pipelining
D Superpipelining
E Throttling
EV
8 True or false? Current processors have both L1 and L2 caches.

True
9 The plain chip called a die is built into a(n) _____________ so that it can connect
to the rest of the circuitry in the computer.
package
10 Which socket type is similar to the Socket 7 design, but with six staggered rows of
pins instead of five?
A Socket 8
Socket 370
C Socket 423
PR
D Socket 478
11 A(n) ________ card is a circuit board that connects to a motherboard to provide

additional expansion slots or sockets.
Riser
223
Independent practice activity

In this activity, youll practice identifying appropriate CPU and motherboard
requirements for a PC.
1 Given a budget of $1000, use the www.motherboards.org Web site to plan the
highest-capability PC that you could purchase. Focus on CPU and motherboard
performance and form factor. Make sure your PC could support a sufficient number
of add-on devices, such as hard drives and CD/DVD drives.
Record the specifications of the system youd purchase here:
CPU (type, model, speed): ____________________________

Motherboard (make and model): _______________________
IE
Form factor and drive bay capacity: ____________
2 If available, examine the motherboard and CPU of a computer in your room, other
than your lab station computer. Record the following information about this
computer:
CPU (type, model, speed): _______________________________________
CPU socket type: ______________________________________________
Motherboard (make and model): ___________________________________
Form factor: ___________________________________________________
EV
Ports (serial, parallel, and so forth): _________________________________
PR
Integrated peripherals: ___________________________________________

CompTIA Server+

Uploaded by

Copyright:

Available Formats

CompTIA Server+

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CompTIA Server+

Uploaded by

Copyright:

Available Formats

W

NOT FOR PRINTING OR INSTRUCTIONAL USE

CompTIA Server+ Certification, 2009 Edition

Vice President, Product Development:

President, Axzo Press:

Director of Publishing Systems Development:

Andy LaPage, Tim Poulsen, Judi Kling

COPYRIGHT 2010 Axzo Press. All rights reserved.

ILT Series is a trademark of Axzo Press.

ISBN 10: 1-4260-1906-8

NOT FOR PRINTING OR INSTRUCTIONAL USE

About the manual............................................................................... iv

Deploying the chassis

Topic A: Form factors...................................................................................... 1-2

Selecting CPUs and motherboards

Topic A: Central processing units.................................................................... 2-2

Managing the BIOS

Topic A: The BIOS and CMOS....................................................................... 3-2

Topic A: Memory ............................................................................................ 4-2

Topic A: Troubleshooting models ................................................................... 5-2

Installing expansion cards

Topic A: Buses................................................................................................. 6-2

Installing data storage devices

Topic A: Installing storage devices.................................................................. 7-2

NOT FOR PRINTING OR INSTRUCTIONAL USE

CompTIA Server+ Certification, 2009 Edition

Installing a network operating system

Topic A: Server roles....................................................................................... 8-2

Topic A: Networking essentials ...................................................................... 9-2

Managing a network server

Topic A: User management............................................................................ 10-2

Documenting and planning

Topic A: Documenting the IT environment ................................................... 11-2

Preparing for disaster

Topic A: Backing up data............................................................................... 12-2

Certification exam objectives map

Topic A: Comprehensive exam objectives ...................................................... A-2

CompTIA Server+ acronyms

Topic A: Acronym list..................................................................................... B-2

Topic A: Course summary............................................................................... S-2

NOT FOR PRINTING OR INSTRUCTIONAL USE

After reading this introduction, you will know

A Use ILT Series manuals in general.

description, course objectives, and a skills

C Set up a classroom to teach this course.

D Get support for setting up and teaching this

NOT FOR PRINTING OR INSTRUCTIONAL USE

CompTIA Server+ Certification, 2009 Edition

Topic A: About the manual

ILT Series philosophy

The manuals contain these major components:

Each element is described below.

NOT FOR PRINTING OR INSTRUCTIONAL USE

An appendix is similar to a unit in that it contains objectives and conceptual

NOT FOR PRINTING OR INSTRUCTIONAL USE

CompTIA Server+ Certification, 2009 Edition

In conceptual text, indicates a new term or feature.

In unit summaries, indicates a key term or concept. In

Indicates code or syntax.