372 5

Experiment 5
Arithmetic Logic Unit (ALU)

Objectives:
To implement and test the circuits which constitute the arithmetic logic circuit (ALU).
Background Information:
The basic blocks of a computer are central processing unit (CPU), memory unit, and input/output unit. CPU
of the computer is basically the same as the brain of a human being. It contains all the registers, control
unit and the arithmetic logic unit (ALU). ALU considered as the most important subsystem in a digital
computer. An arithmetic logic unit (ALU) is a digital circuit which performs arithmetic, logic and shift
operations on two n-bit digital words. Functionally, an ALU can be divided up into three circuits: the
arithmetic circuit, the logic circuit and the shift circuit.
ALU arithmetic Circuit:

The arithmetic circuit performs typical arithmetic operations such as addition, subtraction and increment
or decrement by one. The basic component of an arithmetic circuit is the Full adder. By using a multiplexer
to control the data inputs to the adder, it is possible to obtain different types of arithmetic operations. In
this experiment we will implement a 4-bit arithmetic circuit, its logic diagram is shown in Figure 5-1. The
four multiplexers select either B, B', 0 or 1 for the Y inputs of the full adder. Depending on the selection
inputs and the input carry, the arithmetic circuit can generates the eight arithmetic micro operations listed
in Table 5-1.
S1
0
0
0
0
1
1
1
1
select
S0
Cin
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
Input Y
B
B
B'
B'
0
0
1
1
Output D
D = A + Y + Cin
A+B
A+B+1
A + B'
AB
A
A+1
A1
A
Micro operation
Add
Add with Carry
Subtract with borrow
Subtract
Transfer A
Increment A by 1
Decrement A by 1
Transfer A
Table 5-1 : Function table of the 4-bit arithmetic circuit
Figure 5-1 : Circuit diagram of the 4-bit arithmetic circuit
Equipments:
1.
4x 4-to-1 MUXs (2x 74153 chips).
2.
1x 4-bit full adder (1x 74283 chip).
3.
5X Inverters (1x 7404 chip).
4.
Logic Trainer.
5. Connection leads.
Procedures:
1.
Bring all IC chips necessary to build the circuit from the IC cabinet.
2.
Bring some connection leads with varying lengths.
3.
Derive the wiring diagram for the logic diagram shown in Figure 5-1.
4.
Insure that the power switch of the IC trainer is turned off.
5.
Plug the IC chips into the proper sockets.
6.
Connect the voltage supply and ground lines to the chips.
7.
Use the connection leads to connect the circuit according to the derived wiring diagram.
8.
Once all connections have been done, turn on the power switch of the IC trainer .
9.
Verify the circuit function for all micro operations listed in table 5-1.
10. After finishing the experiment, turn off the power switch, disconnect the wires, and take out the IC
chips from the trainer.
ALU Logic Circuit:

The ALU, logic circuit performs the basic logic micro operations: NOT, AND, OR and XOR. From these four
micro operations all known logic micro operations can be derived. Figure 5-2 shows the logic diagram for
one stage of logic circuit. The four gates generates the four logic operations and the multiplexer select the
desired operation as shown in Table 5-2.
S1
0
0
1
1
S0
0
1
0
1
Output
AB
A+B
AB
A'
Operation
AND
OR
XOR
Complement
Table 5-2 : Function table of the 2-bit logic circuit
Figure 5-2 : Circuit diagram of the 2-bit logic circuit
Equipments:
1.
1x 4-to-1 MUXs (1x 74153 chips).
2.
1x AND Gate (1x 7408 chip).
3.
1x OR Gate (1x 7432 chip).
4.
1x XOR Gate (1x 7486 chip).
5.
1x NOT Gate (1x 7404 chip).
6.
Logic Trainer.
7.
Connection leads.
Procedures:
1.
Bring all IC chips necessary to build the circuit from the IC cabinet.
2.
3.
4.
Plug the IC chips into the proper sockets.
5.
Connect the voltage supply and ground lines to the chips.
6.
7.
Once all connections have been done, turn on the power switch of the IC trainer.
8.
Verify the circuit function.
9.
After finishing the experiment, turn off the power switch, disconnect the wires, and take out the IC
chips from the trainer.
ALU Shift Circuit:

Shift circuit used to perform the shift micro operations. The contents of a register can be shifted serially to
the left or to the right. The shift circuit contains multiplexers as shown in Figure 5-3. when the select line is
0 the 4-bit input data are shifted right. When the select line is 1 the input data are shifted left. There are
two serial inputs one for shift left and other one for shift right. The function table shows the outputs of the
multiplexers in each case.
S
0
1
H3
IR
A2
H3
H2
H1
A3
A2
A1
A0
H0
A1
IL
Table 5-3 : Function table of the 4-bit shift circuit
Figure 5-3 : Circuit diagram of the 4-bit shift circuit
Equipments:
1.
4x 2-to-1 MUXs (1x 74157 chip).
2.
Logic Trainer.
3.
Connection leads.
Procedures:
1.
Bring the IC chip necessary to build the circuit from the IC cabinet.
2.
3.
4.
Plug the IC chip into the proper socket.
5.
Connect the voltage supply and ground lines to the chip.
6.
7.
Once all connections have been done, turn on the power switch of the IC trainer.
8.
Verify the circuit function according to its function table.
9.
After finishing the experiment, turn off the power switch, disconnect the wires, take out the IC
chip from the trainer, put back everything you have used, close IC trainer and clean your table.

372 5

Uploaded by

Copyright:

Available Formats

372 5

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

372 5

Uploaded by

Copyright:

Available Formats

Experiment 5

Arithmetic Logic Unit (ALU)

ALU arithmetic Circuit:

Table 5-1 : Function table of the 4-bit arithmetic circuit

Figure 5-1 : Circuit diagram of the 4-bit arithmetic circuit

4x 4-to-1 MUXs (2x 74153 chips).

1x 4-bit full adder (1x 74283 chip).

5X Inverters (1x 7404 chip).

Bring some connection leads with varying lengths.

Insure that the power switch of the IC trainer is turned off.

Plug the IC chips into the proper sockets.

Connect the voltage supply and ground lines to the chips.

ALU Logic Circuit:

Table 5-2 : Function table of the 2-bit logic circuit

Figure 5-2 : Circuit diagram of the 2-bit logic circuit

1x 4-to-1 MUXs (1x 74153 chips).

1x AND Gate (1x 7408 chip).

1x OR Gate (1x 7432 chip).

1x XOR Gate (1x 7486 chip).

1x NOT Gate (1x 7404 chip).

Insure that the power switch of the IC trainer is turned off.

Plug the IC chips into the proper sockets.

Connect the voltage supply and ground lines to the chips.

Verify the circuit function.

ALU Shift Circuit:

Table 5-3 : Function table of the 4-bit shift circuit

Figure 5-3 : Circuit diagram of the 4-bit shift circuit

4x 2-to-1 MUXs (1x 74157 chip).

Insure that the power switch of the IC trainer is turned off.

Plug the IC chip into the proper socket.

Connect the voltage supply and ground lines to the chip.

Verify the circuit function according to its function table.

You might also like