LO5 Module 1 Installing Computer System and Networks

Sector:
INFORMATION AND COMMUNICATION TECHNOLOGY

Qualification:
COMPUTER HARDWARE SEVICING NC II

Unit of Competency:
INSTALL COMPUTER SYSTEMS AND NETWORKS
Module Title:
INSTALLING COMPUTER SYSTEMS AND NETWORKS
Technical Education and Skills Development

Authority
SOUTHERN ISABELA COLLEGE OF ARTS AND TRADES
Santiago City
TECHNICAL TERMS
Active Hubs amplify or boost signals
Anti-Static A product that prevents the build up of static electricity
BIOS Basic Input/Output System, chip that controls the most basic functions of
the computer and performs a self-test every time you turn it on.
Flash drive RAM that can retain data without electrical power. It is widely used
for BIOS chips and for digital camera and digital music storage.
Graphic tablet objects are drawn using a pen or a puck. The puck is technically
a tablet cursor, not a mouse.
Goggles A large spectacles, with shields around the rims, for protecting the eyes
from dust, excessive light, wind, etc.
Hard-disk drive is a storage device that stores billions of characters of data on a

non-removable disk.
Hardware- refers to the tangible (things you can touch) components of a computer
system. Hardware components are further divided into three groups namely
Host any computer whether mainframe, server, or even PC that acts as an

information source on a network.
Intelligent Hubs select which path a specific signal will travel
Joy Stick - a hand-held control stick that allows a player to control the
movements of a cursor on a computer screen or a symbol in a video game .
LAN Card Local area network interface card.
Laptop computer - A small, portable computer -- small enough that it can sit on
your lap.
Local Area Network- the smallest of the three network types, consist of PCs
connected together within a limited area, such as within the same building, floor
or department.
Mainframe: A powerful multi-user computer capable of supporting many

hundreds or thousands of users simultaneously.
Metropolitan Area Network are network that spans no more than 50 miles. It
is design to connect LANs spanning a town or city
Minicomputer: A multi-user computer capable of supporting up to hundreds of

users simultaneously.
Metropolitan Area Network is a network that spans no more than 50 miles. It

is design to connect LANs spanning a town or city
Motherboard contains the CPU, BIOS, Memory, mass storage interfaces, serial
and parallel ports, expansion slot and all the controllers required to control
standard peripheral devices such as the display screen, keyboard and disk drive
Modem - (Modulator-Demodulator) The modem is a device that allows a given

computer to share data or otherwise a device which let computers exchange
information
Modular Hubs are popular in networks because they are easily expanded and
always have management option. It is purchased as chassis, or card cage, with
multiple card slots, each of which accepts a communication card, or module
Multimedia - is the combination of different types of communication media

(sound, print, video, and so on)
Multitester- is an instrument use to measure voltage, current and resistance.
NIC Network Interface Card The PC expansion board that plug into a personal
computer or server and works with the network operating system to control the
flow of information over the network.
Network is a communications system connecting two or more computers.
Network Bridge divides network into smaller, more manageable sections helping
reduce network traffic.
Network Hub - a hardware device that all PCs on a network are connected to by
cabling. The hub manages receiving and transmitting data from networked
services.
Network Server- is a powerful computer whose sole purpose is to serve network

clients.
Network Switch It helps determine how data moves over large networks.
Notebook computer An extremely lightweight personal computer that weighs

weigh less than 6 pounds and are small enough to fit easily in a briefcase.
OHS Occupational Health and Safety

Operating System (Os) -software that controls the allocation and use of programs
and data that a computer uses.
Passive Hubs simply connects various cables
Personal computer: A small, single-user computer based on a microprocessor.
Port hub /Port is a connector on the back of a computer or other device. A port
is either a serial port or a parallel port.
Peers- mean any computer sharing the same protocol layer with another
computer.
Protocol refers to the specific standards governing the sending and receiving of
data.
Repeater a device that strengthen signals and allow then to stay clear over longer
distances.
Printer - It is a piece of hardware that produces a paper copy (also known as

hardcopy) of the information generated by the computer.
RAM Random Access Memory, is a primary memory. This memory is used

inside the computer to hold programs and data while it is running.
RJ 45 is the connector plugged into the NIC ports on computers and often
connecting the main networking hardware together.
Router a device that forwards data packets between Local or Wide Area Network
groups.
Scanner- it is an input device that read text or illustration printed on paper,

translates the information into a form that a computer can use.
Server is a part of a network. It is a special computer that users on the network
can asses to carry out a particular job.
Software programs and data that a computer uses.
Software applications- enables you to perform specific tasks- solve problems,
perform work, or entertain yourself.
Sound Device Driver Installer / Sound and Audio Devices A windows XP
Control Panel applet, called Sounds, and Multimedia in Windows 2000, for
configuring the systems sound card.
Stackable Hubs work just like standalone hubs, except that several of them can
be stacked (connected) together, usually by short lengths of cable.
Standalone Hubs are single products with a number of ports. It is usually

include some method of linking them to other standalone hubs for network
expansion.
Static The discharge of electricity between two objects with different electrical
potential
Sub notebook computer - A portable computer that is slightly lighter and smaller
than a full-sized notebook computer. Typically, sub notebook computers have a
smaller keyboard and screen, but are otherwise equivalent to notebook computers.
UTP (Unshielded Twisted Pair) least expensive and most popular network media.
USB Universal Serial Bus, a hardware interface for low-speed peripherals such
as the keyboard, mouse, joystick, scanner, printer and telephony devices.
Video Camera - camera using videotape: a camera that records onto videotape
Wide Area Network used to distribute information thousand of miles among

thousands of users.
Wireless Hubs are hubs designed for the home
Workstation- is any network computer that connects to and request resources

from a network
INFORMATION SHEET 1.1-1

OHS Policies and Procedures
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to identify and apply OHS
policies and procedures in Computer Hardware Servicing.
Occupational Health and Safety Policy

Occupational health and safety is a cross-disciplinary area concerned with protecting the safety, health and
welfare of people engaged in work. The goal of all occupational health and safety programs is to foster a
safe work environment. As a secondary effect, it may also protect co-workers, family members, employers,
customers, suppliers, nearby communities, and other members of the public who are impacted by the
workplace environment. It may involve interactions among many subject areas, including occupational
medicine, occupational (or industrial) hygiene, public health, safety engineering, chemistry, health physics.
Safety practices should be learned early and always adhered to when working with
any electrical device, including personal computers and peripherals. This is for the
protection of not only the people working with them, but also for the devices themselves.
The basis for this process begins with your Occupational Health and Safety Policies.
Personal Safety While Working Along With PCs
While working inside your computer, do not attempt to service the computer except as explained in
this guide and elsewhere in product documentation. Always follow the instructions closely.
Computer equipment can be dangerous, and you or others can be injured or even
killed if you dont follow proper safety guidelines when working along PCs. The following
are some precautionary measures to take before working with any computer equipment:
Before you start to work on the computer, perform the following steps in the sequence indicated:
1. Turn off the computer and all peripherals.
2. Touch an unpainted metal surface on the computer chassis, such as the metal around the
card-slot openings at the back of your computer, before touching anything inside your
computer.
3. Disconnect the computer and peripherals from their electrical outlets. Doing so reduces the
potential for personal injury or shock. Also disconnect any telephone or telecommunication
lines from the computer.
NOTE: Before disconnecting a peripheral from the system or removing a component from the
system board, verify that the standby power light-emitting diode (LED) on the system board
has turned off.
While you work, periodically touch an unpainted metal surface on the computer chassis to
dissipate any static electricity that might harm internal components.
In addition, it is recommended that you periodically review the safety instructions in your System
Information Guide.
Additional Safety tips:
Wear shoes with non-conductive rubber soles to help reduce the chance of being
shocked or seriously injured in an electrical accident.
Do not work on components that are plugged into their power source.
Do not remove expansion cards from a computer when it is turned on.
Remove all jewelry when working inside any computer related equipment.
Be sure not to mix electronic components and water.
When you shut down your computer, be sure to shut it down properly. Do not turn
it off with the case switch.
Dont eat or drinks while working.
Self Check 1.1.1

Directions:
Identify at least 10 Occupation health and Safety (OHS) policies and procedures in CHS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Did the Trainee overall performance meet the required
evidence/standard?
Yes
No
ANSWER KEY 1.1-1

10 Occupation health and Safety (OHS) policies and procedures in CHS.
1. Disconnect the computer and peripherals from their electrical outlets.
2. Touch an unpainted metal surface on the computer chassis, such as the metal
around the card-slot openings at the back of your computer, before touching
anything inside your computer
3. Turn off the computer and all peripherals
4. Wear shoes with non-conductive rubber soles to help reduce the
chance of being shocked or seriously injured in an electrical accident.
5. Do not work on components that are plugged into their power source.
6. Do not remove expansion cards from a computer when it is turned on.
7. Remove all jewelry when working inside any computer related
equipment.
8. Be sure not to mix electronic components and water.
9. When you shut down your computer, be sure to shut it down properly.
Do not turn it off with the case switch.
10. Wear anti static materials.

Basic Terms, Concepts, Functions and Characteristics Of PC Hardware Components
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to identify the Basic Terms, Concepts,
Functions and Characteristics of PC Hardware Components
Types of Computer
Workstation
A workstation is a high-end personal computer designed for technical or scientific
applications. Intended primarily to be used by one person at a time, they are commonly
connected to a local area network and run multi-user operating systems.
Desktop computer
Desktop computers come in a variety of styles ranging from large vertical tower
cases to small form factor models that can be tucked behind an LCD monitor. In this
sense, the term 'desktop' refers specifically to a horizontally-oriented case, usually
intended to have the display screen placed on top to save space on the desk top.
Most modern desktop computers have separate screens and keyboards.
Single unit
Single unit PCs (also known as all-in-one PCs) are a subtype of desktop
computers, which combine the monitor and case of the computer within a single unit.
Nettop
A subtype of desktops, called nettops, was introduced by Intel in February 2008 to describe low-cost,
lean-function, desktop computers.
Laptop
A laptop computer or simply laptop, also called a notebook
computer or sometimes a notebook, is a small personal computer
designed for portability.
Netbook
Netbooks (also called mini notebooks or subnotebooks) are a rapidly evolving category of small,
light and inexpensive laptop computers suited for general computing and accessing web-based applications;
they are often marketed as "companion devices," that is, to augment a user's other computer access.
Tablet PC
A tablet PC is a notebook or slate-shaped mobile computer, first introduced
by Pen computing in the early 90s with their PenGo Tablet Computer and
popularized by Microsoft. Its touchscreen or graphics tablet/screen hybrid
technology allows the user to operate the computer with a stylus or digital pen, or
a fingertip, instead of a keyboard or mouse.
Ultra-Mobile PC
The ultra-mobile PC (UMPC) is a specification for a small form factor
of tablet PCs. It was developed as a joint development exercise by
Microsoft, Intel, and Samsung, among others. Current UMPCs typically
feature the Windows XP, Windows Vista, Windows 7, or Linux
operating system and low-voltage Intel Atom or VIA C7-M processors.
Home theater PC
A home theater PC (HTPC) is a convergence device that
combines the functions of a personal computer and a digital video
recorder. It is connected to a television or a television-sized computer
display and is often used as a digital photo, music, video player, TV
receiver and digital video recorder.
Pocket PC
A pocket PC is a hardware specification for a handheld-sized computer (personal
digital assistant) that runs the Microsoft Windows Mobile operating system. It may have
the capability to run an alternative operating system like NetBSD or Linux. It has many
of the capabilities of modern desktop PCs.
HARDWARE
An exploded view of a modern personal computer and peripherals:

1. Scanner
9. Speakers
2. CPU (Microprocessor)
10. Monitor
3. Primary storage (RAM)
11. System software
4. Expansion cards (graphics cards, etc.)
12. Application software
5. Power supply
13. Keyboard
6. Optical disc drive
14. Mouse
7. Secondary storage (Hard disk)
15. External hard disk
8. Motherboard
16. Printer
Computer case
A computer case is the enclosure that contains the main
components of a computer. Cases are usually constructed from steel or
aluminium, although other materials such as wood and plastic have been
used. Cases can come in many different sizes, or form factors.
Processor
The central processing unit, or CPU, is that part of a computer which
executes software program instructions. In older computers this circuitry was
formerly on several printed circuit boards, but in PCs is a single integrated circuit.
Nearly all PCs contain a type of CPU known as a microprocessor. with a fan
attached via heat sink.
Motherboard
The motherboard, also referred to as systemboard or mainboard, is the primary
circuit board within a personal computer.
Main memory
A PC's main memory is fast storage that is directly accessible by the CPU, and is used to store the
currently executing program and immediately needed data.
Hard disk
Mass storage devices store programs and data even when the
power is off; they do require power to perform read and write functions
during usage. Although flash memory has dropped in cost, the prevailing
form of mass storage in personal computers is still the hard disk.
Video card
The video card - otherwise called a graphics card, graphics
adapter or video adapter - processes and renders the graphics output
from the computer to the computer display, and is an essential part of
the modern computer.
Visual display unit
A visual display unit (or monitor) is a piece of electrical equipment,
usually separate from the computer case, which displays viewable images
generated by a computer without producing a permanent record.
Keyboard
In computing, a keyboard is an arrangement of buttons that each correspond to a function, letter, or

number. They are the primary devices of inputting text.
Mouse
A Mouse on a computer is a small, slidable device that users hold and slide
around to point at, click on, and sometimes drag objects on screen in a graphical
user interface using a pointer on screen.
Other components
Mass storage
All computers require either fixed or removable storage for their operating system, programs and
user generated material.
Formerly the 5 inch and 3 inch floppy drive were the principal forms of removable storage for backup of
user files and distribution of software.
Computer communications
Internal modem card
Modem
Network adapter card
Router
Common peripherals and adapter cards
Headset
Joystick
Microphone
Printer
Scanner
Sound adapter card as a separate card rather than located on the motherboard
Speakers
Webcam
LAN Card is a network interface card. This

circuit board or card that is installed in a
that it can be connected to a network.
Modem - (Modulator-Demodulator) The
device that allows a given computer to
otherwise a device which let computers
information
USB Universal Serial Bus, a hardware
interface for low-speed peripherals such as
the keyboard, mouse, joystick, scanner,
printer and telephony devices.
is a computer
computer so
modem is a
share data or
exchange
Scanner- it is an input device that read text

or illustration printed on paper, translates
the information into a form that a computer
can use.
Printer - it is a piece of hardware that

produces a paper copy (also known as
hardcopy) of the information generated by
the computer.
RAM Random Access Memory, is a primary memory. This memory

is used inside the computer to hold programs and data while it is
running.
BIOS Basic Input/Output System, chip that controls the most basic
functions of the computer and performs a self-test every time you turn
it on.
Flash drive RAM that can retain data

without electrical power. It is widely used
for BIOS chips and for digital camera and
digital music storage.
Video Camera - camera using videotape: a

camera that records onto videotape
Self Check 1.1-2
A. Multiple Choice
Direction: Choose the best answer of the given choices. Use a separate sheet of paper in
answering.
1. It is a high end personal computer designed for technical or scientific applications. Intended
primarily to be used by one person at a time, they are commonly connected to a local area
network and run multi-user operating systems.
A. Work Station
B. Nettop
C. Laptop
D. Tablet PC
2. It is a small personal computer designed for portability. Usually all of the interface hardware
needed to operate this computer, such as USB ports (previously parallel and serial ports),
graphics card, sound channel, etc., are built in to a single unit.
A. Work Station
B. Nettop
C. Laptop
D. Tablet PC
3. It is a convergence device that combines the functions of a personal computer and a digital
video recorder.
A. Work Station
B. Home theater PC
C. Laptop
D. Tablet PC
4. It is a hardware specification for a handheld-sized computer (personal digital assistant) that
runs the Microsoft Windows Mobile operating system.
A. Work Station
B. Home theater PC
C. Laptop
D. Pocket PC
5. It is also called mini notebooks or subnotebooks and are a rapidly evolving category of small,
light and inexpensive laptop computers suited for general computing and accessing webbased applications
A. Netbook
B. Home theater PC
C. Work Station
D. Pocket PC
6. It is the enclosure that contains the main components of a computer.
A. Mother Board
B. Computer Case
C. Processor
D. Hard Disk
7. It is the part of a computer which executes software program instructions.
A. Mother Board
B. CPU
C. Processor
D. Hard Disk
8. It is also referred to as systemboard or mainboard, and is the primary circuit board within a
personal computer.
A. Mother Board
B. CPU
C. Processor
D. Hard Disk
9. It processes and renders the graphics output from the computer to the computer display.
A. Memory
B. CPU
C. Video card
D. Hard Disk
10. It is a piece of electrical equipment, usually separate from the computer case, which displays
viewable images generated by a computer without producing a permanent record.
A. Memory
B. CPU
C. Printer
D. Monitor
B. Identification
Directions: Identify the following computer components
Use a separate sheet of paper in answering.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
ANSWER KEY 1.1-2

A. MULTIPLE CHOICE
1. A
7. B
2. C
8. A
3. B
9. C
4. D
10. D
5. A
6. B
B.
IDENTIFICATION
1.
Monitor
2.
Video card
3.
Hard Disk
4.
Memory/ RAM
5.
Mother Board
6.
Processor
7.
Keyboard
8.
Mouse
9.
Printer
10. Scanner

Structure of Operating System
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to be familiar with the structure of Operating
System.
SOFTWARE
A screenshot of the OpenOffice.org Writer software

Computer software is a general term used to describe a collection of computer programs, procedures
and documentation that perform some tasks on a computer system. [29] The term includes application software
such as word processors which perform productive tasks for users, system software such as operating
systems, which interface with hardware to provide the necessary services for application software, and
middleware which controls and co-ordinates distributed systems.
Operating system
An operating system (OS) manages computer resources and provides programmers with an interface
used to access those resources.
Microsoft Windows
Windows 7, the latest client version in the Microsoft Windows line

Microsoft Windows is the collective brand name of several software operating systems by Microsoft.
Microsoft first introduced an operating environment named Windows in November 1985 as an add-on to
MS-DOS in response to the growing interest in graphical user interfaces (GUIs).[31][32][not in citation given] The most
recent client version of Windows is Windows 7 and Windows Server 2008 R2 which was available at retail
on October 22, 2009.
Mac OS X
Mac OS X Snow Leopard desktop

Mac OS X is a line of graphical operating systems developed, marketed, and sold by Apple Inc.. Mac
OS X is the successor to the original Mac OS, which had been Apple's primary operating system since 1984.
Unlike its predecessors, Mac OS X is a Unix-based graphical operating system.
Linux
A Linux distribution (Kubuntu) running the KDE 4 desktop environment.

Linux is a family of Unix-like computer operating systems. Linux is one of the most prominent
examples of free software and open source development: typically all underlying source code can be freely
modified, used, and redistributed by anyone. [33] The name "Linux" comes from the Linux kernel, started in
1991 by Linus Torvalds.
Applications
GIMP raster graphics editor

A computer user will apply application software to carry out a specific task. System software
supports applications and provides common services such as memory management, network connectivity, or
device drivers; all of which may be used by applications but which are not directly of interest to the end
user.
Software applications
Software - is the programs and data that a computer uses.
Network OS Software
Network-are multiple computers linked together to make simultaneous
information sharing and exchange by multiple users.
Sound Device Driver Installer / Sound and Audio Devices A windows XP

Control Panel applet, called Sounds, and Multimedia in Windows 2000, for
configuring the systems sound card.
SELF CHECK 1.1-3

A. Multiple Choice
Direction: Choose the best answer of the given choices. Use a separate sheet of paper in
answering.
1. It is a general term used to describe a collection of computer programs, procedures and documentation
that perform some tasks on a computer system.
A. Hardware
B. Software
C. Utility
D. Application
2. It manages computer resources and provides programmers with an interface used to access those
resources.
A. Operating System
B. Software
C. Utility
D. Application
3. It is one of the most prominent examples of free software and open source development operating
system.
A. Linux
B. Software
C. Utility
D. Application
4. It is a line of graphical operating systems developed, marketed, and sold by Apple Inc..
A. Linux
B. Mac OS X
C. Windows
D. Application
5. It is the collective brand name of several software operating systems by Microsoft.
A. Linux
B. Mac OS X
C. Windows
D. Application
ANSWER KEY 1.1-3

1. B
2. A
3. A
4. B
5. C

System Configuration / Settings of computer system and devices
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to be familiar with System
Configuration / Settings of computer system and devices.
System Configuration
System Configuration Utility overview

The System Configuration utility automates the routine troubleshooting steps that
Microsoft Customer Support Services professionals use when they diagnose system
configuration issues. When you use this utility to modify the system configuration, you
can select check boxes to eliminate issues that do not apply to your configuration. This
process reduces the risk of typing errors that you may make when you use any text
editor, such as Notepad. You must be logged on as an administrator or as a member of
the Administrators group to use the System Configuration utility.
When you use the System Configuration utility, you can easily reset or change the
configuration settings in Windows to include preferences for the following files and
settings:
The System.ini file
The Win.ini file
The Boot.ini file
Programs that are set to load during the startup process (these programs are
specified in the Startup folder and in the registry)
Environment settings
International settings
There are two methods for troubleshooting configuration issues by using the System
Configuration utility. Read each method carefully to understand the consequences of
each method.
Method 1: Diagnostic and Selection startup modes
Diagnostic startup
Diagnostic startup enables Windows to determine the basic device drivers and
software to load when you start Windows. When you use this method, the system
temporarily disables Microsoft services such as Networking, Plug and Play, Event
Logging, and Error Reporting. Also, you permanently delete all restore points for the
System Restore utility.
Note Do not use this method if you want to save your restore points for System Restore
or if you must use a Microsoft service to test a problem.
To perform a diagnostic startup, follow these steps:
1. Click Start, click Run, type msconfig, and then click OK.
2. On the General tab, click Diagnostic Startup, and then click OK.
3. Restart your computer.
If the problem does not occur, use Selective startup mode to try to find the problem by
turning individual services and startup programs on or off.
Selective startup
Selective startup enables you to select the files and the settings that you want the
computer to load when you restart the computer. Select from the following options:
Process System.ini File

Process Win.ini file
Load System Services
Load Startup Items
By default, no options are selected. The following actions apply to these options:
When you select the check box, the configuration file is processed when you
restart the computer.
When you clear the check box, the configuration file is not processed when you
restart the computer.
When the check box is selected, and you cannot select the check box because it
appears dimmed, some items are still loading from that configuration file when
you restart the computer.
When the check box is not selected, and you cannot select the check box because
it appears dimmed, the configuration file is not present on the computer.
You cannot change the Use Original BOOT.INI option button.
Note When you clear the Load System Services check box, you disable Microsoft
services such as Networking, Plug and Play, Event Logging, and Error Reporting. You
also permanently delete all restore points for the System Restore utility. Do not clear this
check box if you want to keep your restore points for System Restore, or if you have to
use a Microsoft service to test a problem.
To perform a selective startup, follow these steps:

2. On the General tab, click Selective Startup.
3. Select or clear the available settings.
4. Click OK.
6. Repeat steps 1 through 5 until you find the problem.
Change individual file settings
If you know the different settings in each configuration file, you can enable or disable
individual settings in the file that has the tab for that file in the System Configuration
utility. To prevent individual items in a configuration file from loading when you restart
your computer, follow these steps:
2. Click a tab: System.ini, Win.ini, Boot.ini, Services, or Startup.
3. Select or clear the available settings.
4. Click OK.
6. Repeat steps 1 through 5 until you find the problem.
System.ini and Win.ini options
The SYSTEM.INI and WIN.INI tabs in the System Configuration utility have the
following options:
Check boxes enable you to enable or to disable an option. To enable an option so
that it loads at startup, select the check box or select the option, and then click
the Select button. To disable an option so that it does not load at startup, clear
the check box or select the option, and then click the Disable button.
Move Up and Move Down buttons enable you to move through the different
options when you do not have a mouse.
The New button enables you to create a new entry in the System.ini or in the
Win.ini file. Click the button, and type your entry.
The Edit button enables you to edit an existing line in the System.ini or in the
Win.ini file. Click the button, and edit the line.
When a check box is unavailable on the SYSTEM.INI and WIN.INI tabs, the System
Configuration utility temporarily removed the lines.
Note When you click to clear a check box for an item or a line, the Selective Startup
option on the General tab is automatically selected.
Manually extract a file
If you have to fix a corrupted file, extract the individual Windows file from the CAB
files. To do this, follow these steps:
2. On the General tab, click Expand File.
3. In the File to restore box, type the name of the file that you want to restore.
4. In the Restore from box, type the path of the Windows XP .cab file from which
you want to restore the file. Or, click Browse From to locate the Windows XP .cab
file.
Note The Windows XP .cab files are stored in the I386 folder on the Windows XP
installation CD.
5. In the Save file in box, type the path of the folder to which you want to extract the
new file. Or, click Browse To to locate the folder that you want.
6. Click Expand.
7. In the System Configuration Utility dialog box, click OK. If you are prompted to
restart the computer, click Restart.
Return to normal startup

After you complete your troubleshooting and fix your configuration, return to a
normal startup. Follow these steps:
2. On the General tab, click Normal startup.
3. Click OK.
Method 2: System restore
You can use the System Configuration utility to perform a system restore. There are
three possible restore points:
System checkpoints that Windows schedules
Manual restore points that you specify with the System Configuration utility
Installation restore points that occur before you install a program or a service
You can use the system checkpoints or the installation restore points to restore your
computer's settings to a date when it operated correctly. This may also help determine
the
cause
of
the
configuration
error.
To perform a system restore, follow these steps:
2. On the General tab, click Launch System Restore.
3. Select Restore my computer to an earlier time, and then click Next.
4. Calendar dates in bold are possible restore points. Click the most recent one to
view system restore information.
5. Select a system checkpoint or an installation restore point, and then click Next.
6. Close all other programs.
7. To start the system restore, click Next.
8. Your computer restarts.
9. Repeat steps 1 through 8 until you fix your configuration issue.
Assigning Resources to Devices

Many devices have fixed resource assignments that cannot be changed. Most
system devices are like this. In addition, it is generally best not to change (or try to
change) the resource settings for standard devices like IDE hard disk controllers unless
you both really know what you are doing and there is a compelling reason to change
them. The following devices usually have hard-coded resource settings that cannot be
changed: system devices, keyboard, PS/2 mouse, floppy disk controller, primary IDE
controller, video card. Others can generally be changed, although it makes more sense
for some devices than for others.
There are several different ways that are generally used to set or change resource
settings for devices:
Hardware Settings: Resource assignments on some cards, especially older ones,

is done by hardware on the device itself. This involves changing the settings of
jumpers and switches, usually on the circuit board of the device, to tell it what
resources to use.
Software Configuration Programs: Many newer cards are configured using

special software config programs that come with them.
Plug and Play: Newer devices that subscribe to the Plug and Play standards can
be automatically configured under certain conditions when used in a machine that
supports Plug and Play, with an operating system that supports it. Plug and Play
is an attempt to eliminate the large amount of work in assigning resources to
devices and resolving conflicts.
Tip: It is always a good idea, once you have your system configured in a way
that makes sense and works for you, to record the system configuration for
future reference
Resource Conflicts and Conflict Resolution

As discussed in several other areas of this section, one of the major issues with
system resources is configuring your system's devices so that they don't interfere with
each other. When more than one device attempts to use the same resource, the result is
a resource conflict.
The Nature of Resource Conflicts
Resource conflicts can manifest themselves in several different ways. Some conflicts
can be very easy to recognize; others can be extremely difficult to find and correct,
because they manifest themselves indirectly, or through symptoms that may not seem to
have anything to do with the device causing the problem. Here are some of the ways that
resource conflicts manifest themselves. Some of these may be consistent and repeatable,
while others may be intermittent:
System hangs or lockups, particularly while using a peripheral device.

(Memory) parity errors on parity-enabled systems.
Noise or other problems from sound cards.
Junk being printed on your printer.
The mouse pointer hanging and refusing to move, or moving in a stuttering
fashion.
Errors and crashes of applications for no apparent reason.
As you can see, some of these obviously point to a resource problem, but many do
not. For example, system crashes can be caused by many non-resource-related factors. If
your mouse works until you try to use your modem, well, you can probably figure out
what the problem is, or at least where to start looking. In general, if you just added a
new peripheral to your PC and a resource conflict is indicated, the new device is almost
certainly involved somehow.
Resource Conflict Resolution
If you suspect a resource conflict in your PC, you of course need to resolve this
conflict. This can be easy to do if you know where to start looking, or very hard if you do
not. There are some general steps that can be followed to fix this sort of problem. In very
brief terms the steps are:
Determine what all the devices in the system are using for resources.
Identify the conflicting devices.
Change the resource settings on one or more of
devices so they are no longer conflicting.
the
Using the Windows XP Control Panel

The Control Panel in Windows XP is where many of
your
administrative and configuration tools are located. Other versions of Windows have a
Control Panel as well but we will focus on Windows XP since that is what the majority of
Windows users use. To get to the Control Panel click on Start and then Control Panel or
Start, Settings, Control Panel depending on what Start Menu you are using.
Now we will go over the functions of the various Control Panel icons so you can get an
idea of what they are for and how you can use them to improve your Windows
experience.
Accessibility Options - Here you can change settings for your keyboard, mouse, display
and sound.
Add Hardware - This will open the Add Hardware Wizard which will search your
computer for new hardware that you have installed when Windows does not recognize it
on its own.
Add or Remove Programs - If you need to install or uninstall any software on your
computer, this is where you will do it. You should always uninstall software rather than
delete it from your hard drive.
Administrative Tools - This section of your Control Panel is used for administrative
functions such as managing your computer, monitoring performance, editing your
security policy and administering your computer's services.
Automatic Updates - Here is where you tell Windows how and when to update itself.
You can control whether or not it downloads updates automatically or at all and when
you want them installed or to ask you before installing them.
Bluetooth Devices - If you are using any Bluetooth devices on your computer here is
where you can add, remove and manage them.
Date and Time - This one explains itself. You can set your computer's date, time and
regional settings here.
Display - The display settings allow you to change the way things appear on the screen.
You can adjust items like the screen resolution and color depth. Here is where you can
select your background wallpaper and setup your screensaver.
Folder Options - This is where you can adjust the way you view your files and folders
from within My Computer or Windows Explorer.
Fonts - The Fonts applet allows you to add, remove and manage fonts on your computer.
It will show you what fonts are installed in your system.
Game Controllers - If you use a joystick, steering wheel or any other type of game
controller you can use this section to add, remove and troubleshoot the devices.
Internet Options - If you use Internet Explorer for your web browser you will go here to
change settings such for history, connections and security among other things.
Keyboard - Here you can adjust settings such as how fast the keyboard will repeat a
character when a key is held down and the cursor blink rate.
Mail - The Mail applet lets you adjust your properties for your Outlook or Exchange
email settings.
Mouse - Here you can adjust your mouse setting for features such as double click speed,
button assignment and scrolling. You can also change your mouse pointers and effects
as well as view details about your mouse.
Network Connections - This item is where you can check and adjust your network
connection settings. It will take you to the same place as if you were to right click My
Network Places and choose properties. It will show all of your active network, dialup and
wireless connections. There is also a New Connection Wizard to help you setup a new
connection.
Phone and Modem Options - If you have a modem installed on your system and use it
for dialup connections or faxing you can change the settings here. The Dialing Rules tab
allows you to change settings for things such as dialing a number to get an outside line
and setting up carrier codes for long distance and using calling cards. The Modems tab
allows you to add, remove and changed the properties for installed modems. The
Advanced tab is for setting up telephony providers.
Power Options - Here is where you adjust the power settings of your computer. Windows
has built in power schemes for different settings such as when to turn off the monitor or
hard drives and when to go into standby mode. You can even create your own schemes
and save them. The advanced tab allows you to assign a password to bringthe computer
out of standby and tell the computer what to do when the power or sleep buttons are
pressed. If you want to enable hibernation or configure an attached UPS then you can do
it here as well. This area can also be accessed from the display properties settings under
the Screensaver tab.
Printers and Faxes - This area is where your printers are installed and where you would
go to manage their settings. It's the same area that is off of the Start menu. There is an
add printer wizard which makes it easy to install new printers. To manage a printer you
would simply right click it and select properties.
Regional and Language Options - If you need to have multiple languages or formats for
currency, date and time you can manage them here.
Scanners and Cameras - Windows provides a central place to manage your attached
scanners and camera and adjust their settings. There is even a wizard to add new
devices to make the process of installing a scanner or camera easier.
Scheduled Tasks - This item provides the ability for you to schedule certain programs to
run at certain times of the day. For example if you have a batch file you want to run
every night you can set it up here. You can also have it run a program at any scheduled
interval you choose. There is a handy wizard to help you through the process.
Security Center - The Windows Security Center checks the status of your computer for
the stats of your firewall, virus protection and automatic updates. A firewall helps
protect your computer by preventing unauthorized users from gaining access to it
through a network or the Internet. Antivirus software can help protect your computer
against viruses and other security threats. With Automatic Updates, Windows can
routinely check for the latest important updates for your computer and install them
automatically.
Sounds and Devices - Here is where you can adjust your sound and speaker settings.
The Volume tab has settings to mute your system, have a volume icon placed in the
taskbar and tell your computer what type of speakers you are using such as a 5.1
system. The sounds tab lets you adjust what sounds occur for what windows events. If
you need to change what device is used for playback and recording you can do it under
the Audio tab. Voice playback and recording settings are under the Voice tab. To
troubleshoot your sound device you can use the Hardware tab. This is where you can get
information about your particular sound device.
Speech Properties - Windows has a feature for text to speech translation where the
computer will read text from documents using a computer voice that you can hear
through your speakers. The type of voice and speed of the speech can be adjusted here.
System - If you have ever right clicked My Computer and selected Properties then you
have used the System feature of Control Panel. This area gives you information about
your computer's configuration, name and network status. You can click on the Hardware
tab to view details about hardware profiles and driver signing as well as get to Device
Manager. The Advanced tab lets you change settings for virtual memory (page files) and
other performance settings. There is also an area to change startup and recovery settings
if needed. If you want to enable remote access to your computer for Remote Desktop or
Remote Assistance you can enable it here.
Taskbar and Start Menu - This is where you change the setting for your taskbar and
Start menu..
User Accounts - If you need to manage your local computer users then here is where
you need to go. You can add remove users and change the account types for users who
log into your system.
Windows Firewall - This is the same firewall setting described in the Windows Security
Center section.
Wireless Network Setup Wizard - This wizard is used to help you setup a security
enabled wireless network in which all of your computer and devices connect through a
wireless access point.
SELF-CHECK 1.1-4
A. Multiple Choice
Direction: Choose the best answer of the given choices. Use a separate sheet of
paper in answering.
1. Starts Windows in the usual manner.
A. Normal Startup
B. Diagnostic startup
C. Selective startup
D. Safe Mode
2. Starts Windows with basic services and drivers only. This mode can help rule out
basic Windows files as the problem.
A. Normal Startup
D. Safe Mode
3. Starts Windows with basic services and drivers and the other services and startup
programs that you select.
A. Normal Startup
D. Safe Mode
4. Here you can change settings for your keyboard, mouse, display and sound.
A. Accessibility Options
B. Add or Remove Programs
C. Administrative Tools
D. Folder Options
5. You can set your computer's date, time and regional settings here.
A. Accessibility Options
C. Date and Time
D. Folder Options
6. Here is where you adjust the power settings of your computer.
A. Power Options
C. Date and Time
D. Folder Options
7. This item provides the ability for you to schedule certain programs to run at certain
times of the day.
A Scanners and Cameras
C. Date and Time
D. Scheduled Tasks
8. This area gives you information about your computer's configuration, name and
network status.
A. System
C. Date and Time
D. Scheduled Tasks
9. If you need to manage your local computer users then here is where you need to go.
A. System
C. User Accounts
D. Scheduled Tasks
10. This area is where your printers are installed and where you would go to manage
their settings.
A. Printers and Faxes

C. User Accounts
D. Scheduled Tasks
B.
True of False
1. Many devices have fixed resource assignments that cannot be changed.
2. Disabling applications that normally run at boot time might result in related
applications starting more slowly or not running as expected.
3. One key to a well-tuned, trouble-free system is making sure it is properly
configured.
4. Resource assignments on some cards, especially older ones, is done by hardware
on the device itself.
5. Newer devices that subscribe to the Plug and Play standards cannot be
automatically configured.
ANSWER KEY 1.1-4

1. A
6. A
2. B
7. D
3. C
8. A
4. A
9. C
5. C
10. A
B. True of False
1.
2.
3.
4.
5.
TRUE
TRUE
TRUE
TRUE
FALSE

Personal Protective Equipment
LEARNING
OUTCOME #2
Install Equipment, Device / System
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to be familiar and use the
Personal Protective Equipment properly.
Personal Protective Equipment
It refers to protective clothing, helmets, goggles, or other gear designed to protect
the wearer's body or clothing from injury by electrical hazards, heat, chemicals, and
infection, for job-related occupational safety and health purposes.
PPE can also be used to protect the working environment from pesticide
application, pollution or infection from the worker (for example in a microchip factory).
Students even teacher during their laboratory period should require to use of
personal protective equipment. Some of these are:
Goggles A large spectacles, with

shields around the rims, for
protecting the eyes from dust,
excessive light, wind, etc.
Rubber Sole A special type of

shoes used to prevent electrical
shock and for waterproofing and
insulating purposes.
Apron A garment worn over the

front of the body as a protection for
ones cloth.
Dust Mask- A covering for the face

to
prevent
the
inhaling
or
absorbing
dust
and
other
chemicals
Gloves The covering material

with a separate sheath for each
finger used for hand protection.
Anti-Static and Safety Precautions

The little shock you experienced while you are walking across a carpeted floor or
touched a door knob, table, counter or even another person is a result of static
electricity. Static electricity is the discharge of electricity between two objects with
different electrical potential. Humans can't feel a static shock until it is several thousand
volts strong, but it takes less than 30 volts to fry a sensitive computer component, such
as a stick of RAM or a processor.
That's why computer technicians and home computer builders have to guard their
computers against the deadly ravages of static electricity, as well as take steps to avoid
injury to yourself
Safety and Anti-Static Rules
When possible, try to avoid working in carpeted areas. Carpeting greatly increases
static buildup within your body.
Always use an anti-static wrist strap when working on a computer (except when
working on monitors
Always disconnect a computer from the AC power and from any powered
peripherals while you are working on it.
Always grasp a metal part of the computer chassis with your bare hand before you
touch anything inside. Do this even if you are wearing an anti-static wristband.
Always handle electronic components by a non-conducting (non-metallic) edge.

Don't touch the pins or other connectors.
Never plug an ATX power supply into AC power unless it is connected either to a
computer's motherboard or to a dummy test load.
Always use a UL-approved surge protector or an Uninterruptible Power Supply

that incorporates surge and spike protection.
Never eat, drink, or smoke while working on a computer.
Self Check 1.2-1

Instruction: Match the following images to their names and uses.
Apron A garment worn
over the front of the body
as a protection for ones
cloth
. Gloves The covering
material with a separate
sheath for each finger used
for hand protection.
.
Goggles
A
large
spectacles,
with
shields
around
the
rims,
for
protecting the eyes from
dust, excessive light, wind,
etc.
Rubber Sole A special
type of shoes used to
prevent electrical shock and
for
waterproofing
and
insulating purposes
Dust Mask- A covering for
the face to prevent the
inhaling or absorbing dust
and other chemicals
Answer Key
Apron A garment worn

over the front of the body
as a protection for ones
cloth
. Gloves The covering
material with a separate
sheath for each finger used
for hand protection.
.
Goggles
A
large
spectacles,
with
shields
around
the
rims,
for
protecting the eyes from
dust, excessive light, wind,
etc.
Rubber Sole A special
type of shoes used to
prevent electrical shock and
for
waterproofing
and
insulating purposes
Dust Mask- A covering for
the face to prevent the
inhaling or absorbing dust
and other chemicals
ACTIVITY SHEET 1.2-1

PPE
Performance Objective:
The will be divided into groups. Each group has their own respective leader. The
group will prepare a skit regarding personal protective equipment. After the activity they
will be assessed thru the given Performance Criteria Checklist below:
PERFORMANCE CHECKLIST
Did you
1. Clearly identified personal protective equipment.
1. Utilized actual tools/device in performing the skit.
Yes
No
3. Applied safety precautions during the play.

4. Gave more critical thinking on the personal protective
equipment.
6. Cooperatively performed the play.

Introduction to Computer Operating System
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to be familiar with the
different operating systems, navigate on the different OS components and install
Operating system and device drivers.
Operating System (Os)
is a software that manages computer resources and provides programmers/users
with an interface used to access those resources.
is a layer of software which takes care of technical aspects of a computer's

operation. It shields the user of the machine from the low-level details of the
machine's operation and provides frequently needed facilities.
Below is a listing of common operating systems available today, and who developed them.
Operating system
Developer
Operating system
Developer
Corel Linux
Linux
MAC OS 8
MAC OS 9
MAC OS 10
MAC OS X
Mandrake Linux
MS-DOS 1.x
MS-DOS 2.x
MS-DOS 3.x
MS-DOS 4.x
Corel
Linux Torvalds
Apple
Apple
Apple
Apple
Mandrake
Microsoft
Microsoft
Microsoft
Microsoft
MS-DOS 5.x
MS-DOS 6.x
Windows 2000
Windows 2003
Windows 95
Windows 98
Windows CE
Windows ME
Windows NT
Windows Vista
Windows XP
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
The Purpose of an Operating System

The operating system (OS) controls almost all functions on a
computer.
Roles of an Operating System
All computers rely on an operating system (OS) to provide
the interface for interaction between users, applications,
and hardware.
The operating system boots the computer and manages the file system.
Almost all modern operating systems can support more than one user, task, or
CPU.
The operating system has four main roles:
Control hardware access
Manage files and folders
Provide user interface

Manage applications
Characteristics of Operating Systems

Control hardware access
OS automatically discovers and configures PnP
hardware
File and folder management
User interface
Command line interface (CLI)
Graphical user interface (GUI)
Application management
Open Graphics Library (OpenGL)
DirectX
The Types of Operating Systems

Command Line Interface (CLI): The user types
commands at a prompt.
Graphical User Interface (GUI): The user interacts

menus and icons.
with
Most operating systems include both a GUI and a CLI.

Compare Operating Systems
Terms often used when comparing operating systems:
Multi-user Two or more users can work with programs and share peripheral
devices, such as printers, at the same time.
Multi-tasking The computer is capable of operating multiple applications at the
same time.
Multi-processing The computer can have two or more central processing units
(CPUs) that programs share.
Real
Multi-threading A program can be broken into smaller parts that can be loaded
as needed by the operating system. Multi-threading allows individual programs to
be multi-tasked.
Mode
Executes only one program at a time
Addresses only 1 MB of system memory at a time
Directly accesses memory and hardware
Subject to crashes
Available to all modern processors
Only used by DOS and DOS applications
Protected Mode
Has access to all memory
Can manage multiple programs simultaneously
Allows the system to use virtual memory
Provides 32-bit access to memory, drivers, and I/O transfers
Each program is assigned a space in memory
Computer is protected from program errors
Virtual Real Mode
Allows a real-mode application to run within a protected-mode operating system
Creates virtual machines for each program that runs in real mode
Each virtual machine receives 1 MB of memory and access to hardware
In the event of a program error, only the virtual machine is affected
OS provides virtual machine to host the code and protect the PC

Desktop operating systems:
Microsoft Windows: Windows XP
Macintosh: Mac OS X
Linux: Fedora, Ubuntu, and others
UNIX
A desktop OS has the following characteristics:
Supports a single user
Runs single-user applications
Shares files and folders on a small network with limited security
Network Operating Systems (NOS)
Common NOS include:
Novell Netware
Microsoft Windows Server
Linux
UNIX
A network OS has the following characteristics:
Supports multiple users
Runs multi-user applications
Is robust and redundant
Provides increased security compared to desktop operating systems
Determine Proper Operating System
To select the proper operating system:
Create an accurate profile of your customer by analyzing the daily, weekly, and
monthly computer activities
Select appropriate software and hardware to satisfy existing and future
requirements
What Does Your Customer Require?
Office applications
word processing, spreadsheets, or presentation software
Graphics applications
Photoshop or Illustrator
Animation applications
Flash
Business applications
accounting, contact management, sales tracking or database
Identify Minimum Hardware Requirements
Customer may need to upgrade or purchase additional hardware to support the
required applications and OS.
A cost analysis will indicate if purchasing new equipment is a better idea than
upgrading.
Common hardware upgrades:
RAM capacity
Hard drive size

Processor speed
Video card memory and speed
Hardware Compatibility List (HCL)

Most operating systems have an HCL.
HCLs can be found on the manufacturer's website.
HCL includes list of hardware that is known to work with the operating system.
Installing the Operating System
Reasons to perform a clean installation of an OS:
When a computer is passed from one employee to another
When the operating system is corrupted
When a new replacement hard drive is installed in a computer
Before performing a clean installation:
Back up all data first
Explain to the customer that existing data will be erased
Confirm that all needed data has been successfully transferred
Hard Drive Setup Procedures
Operating system setup methods:
Install an OS over a network from a server
Install from a copy of the OS files stored on the hard drive
Install from OS files stored on CDs or DVDs
Partitioning and Formatting
Hard drive must be logically divided (partitioned)
File system must be created on the hard drive
During the installation phase, most operating systems will automatically partition
and format the hard drive
Hard Drive Setup Procedures
A technician should understand the process related to hard drive setup.
Prepare the Hard Drive

The first portion of the installation process deals with formatting and partitioning
the hard drive.
The second portion prepares the disk to accept the file system.
The file system provides the directory structure that organizes the user's operating
system, application, configuration, and data files.
Examples of file systems:
The FAT32 file system
The New Technology File System (NTFS)
Install the Operating System

During the Windows XP installation the user must
provide:
Define currency and numerals

Text input language
Name of user
Name of company
Product key
Computer name
Administrator password
Date and time settings
Network settings
Domain or workgroup information
Create Administrator Account

Setup creates the administrator account with the user name administrator
Change this name to keep the administrator account secure
Only use the administrator account occasionally for critical system changes
Create a fictitious user account to use as a template
Use secure passwords
These should be a minimum of 7 characters, containing at least one of each (letter,
number, and symbol)
Complete the Installation
When Windows XP installation completes:
Computer will reboot
Log in for the first time
Register Windows XP and verify that you are using a legal copy of the OS
Verification enables you to download patches and service packs
Use Microsoft Update Manager to
scan for new software and to:
Install all service packs

Install all patches
Check Device Manager for Conflicts
Look for warning icons (yellow exclamation points)

Double-click to learn about the problem
Click the plus (+) sign to expand the category
May be able to ignore an error
Custom Installation Options

With
Microsoft System Preparation

Follow these steps for disk cloning:
Create a master installation on one computer
Run Sysprep
Create a disk image of the configured computer using third-party disk-cloning
software
Copy the disk image onto a server
When the destination computer is booted,
A shortened version of the Windows setup program runs
Setup configures only user-specific and computer-specific settings
An answer file provides data normally required during set up
The Boot Sequence for Windows XP

Power On Self Test (POST)
POST for each adapter card that has a BIOS
BIOS reads the Master Boot Record (MBR)
MBR takes over control of the boot process and starts NT Loader (NTLDR)
NTLDR reads the BOOT.INI file to know which OS to load and where to find the OS
on the boot partition
NTLDR uses NTDETECT.COM to detect any installed hardware
NTLDR loads the NTOSKRNL.EXE file and HAL.DLL
NTLDR reads the registry files and loads device drivers

NTOSKRNL.EXE starts the WINLOGON.EXE program and displays the Windows
login screen
NTLDR and the Windows Boot Menu

If more than one OS is present on the disk, BOOT.INI gives the user a chance to
select which to use.
Otherwise:
NTLDR runs NTDETECT.COM to get information about installed hardware
NTLDR then uses the path specified in the BOOT.INI to find the boot partition
NTLDR loads two files that make up the core of XP: NTOSKRNL.EXE and HAL.DLL
NTLDR reads the Registry files, chooses a hardware profile, and loads device
drivers
The Windows Registry
Recognized by distinctive names, beginning with HKEY_
Every setting in Windows is stored in the registry
Changes to the Control Panel settings, File Associations, System Policies, or
installed software are stored in the registry
Each user has their own section of the registry
The Windows logon process uses the registry to set the system to the state that it
was in the last time the user logged in
The Windows Registry Files
The NT Kernel and Security Authority

Next, the NT kernel, NTOSKRNL.EXE, takes over
It starts the login file, WINLOGON.EXE
That program starts the Local Security Administration file, LSASS.EXE (Local
Security Administration)
LSASS.EXE is the program that displays the XP welcome screen
There are few differences between the Windows XP and the Windows 2000 boot
process
Manipulating Operating System Files

After you have installed Windows XP, you can use MSCONFIG for post-installation
modifications:
This boot configuration utility allows you to set programs that will run at startup,
and to edit configuration files

The registry is a database that contains information and settings for all of the
hardware, software, users and preferences. REGEDIT allows users to edit the
registry.

Pressing the F8 key during the boot process opens the Windows Advanced Startup
Options menu, which allows you to select how to boot Windows.
Safe Mode Starts Windows but only loads drivers for basic components, such as
the keyboard and display.
Safe Mode with Networking Support Starts Windows identically to Safe Mode and
also loads the drivers for network components.
Safe Mode with Command Prompt Starts Windows and loads the command
prompt instead of the GUI interface.
Last Known Good Configuration Enables a user to load the configurations
settings of Windows that was used the last time that Windows successfully
started. It does this by accessing a copy of the registry that is created for this
purpose.
Describing Directory Structures
Windows file system naming conventions:
Maximum of 255 characters may be used

Characters such as a period (.) or a slash (\ /) are not allowed
An extension of three or four letters is added to the filename to identify the file
type
Filenames are not case sensitive
Windows filename extension examples:
.doc - Microsoft Word
.txt - ASCII text only
.jpg - graphics format
.ppt - Microsoft PowerPoint
.zip - compression format
Describing Directory Structures

Each file has a set of attributes that control how the file may be viewed or altered.
The following are the most common file attributes:
R - The file is read-only
A - The file will be archived the next backup
S - The file is marked as a system file and a warning is given if an attempt is made
to delete or modify the file
H - The file is hidden in the directory display
The ATTRIB Command
NTFS and FAT32

FAT32 is used where files need to be accessed by multiple versions of Windows.
FAT32 is not as secure as NTFS
NTFS can support more and larger files than FAT32, and provides more flexible
security features for folders, files, and sizes
Partitions can be converted from FAT32 to NTFS using the CONVERT.EXE utility,
but not in the reverse direction
Navigating a Graphical User Interface (GUI)
A GUI provides graphical representations of all the files, folders, and programs on
a computer.
Customizing the Desktop

To customize any of these, simply right-click the item and then select Properties.
Taskbar
Recycle Bin
Desktop background
Window appearance
The Start Menu
Customized to two styles, XP and Classic
Accessed by clicking the Start button
The Start menu includes:
A nested list of all installed applications
A list of recently opened documents
A list of other elements, including; a
search
feature, a help center, and system settings
My Computer
When you right-click My Computer and select
Properties, there
are several settings that can be customized:
Computer name
Hardware settings
Virtual memory
Automatic updates
Remote access
Files can also be moved and copied using My Computer
Launching Applications
Applications can be launched in several ways:
Click the application on the Start menu
Double-click the application shortcut icon on the desktop
Double-click the application executable file in My Computer
Launch the application from the Run window or command line
To view and configure network connections, right-click the My Network Places icon.
Connect to or disconnect from a network drive
Right-click Properties to configure existing network connections, such as a wired
or wireless LAN connection
Control Panel Applets
Display Settings
Change the resolution and color quality
Change wallpaper, screen saver, power settings, and other options, by clicking the
Advanced button
Device Manager
Used to view settings for devices in the
An exclamation mark indicates a problem
device
Task Manager
View all applications that are currently
Close any applications that have stopped
responding
Monitor the performance of the CPU and
memory
computer
with a
running
virtual
View all processes that are currently running

View information about the network connections
Event Viewer and Remote Desktop

Event Viewer
Logs a history of events regarding applications, security, and the system.
These log files are a valuable troubleshooting tool.
Remote Desktop
Allows one computer to remotely take control of another computer.
This troubleshooting feature is only available with Windows XP Professional.
Performance Settings
Settings for advanced visuals and for
memory
virtual
Add or Remove an Application

Utility to install or uninstall applications
Tracks installation files for future thorough uninstall, if desired
Upgrading an Operating System
Upgrade Paths
Upgrading to Windows XP
1. Insert the Windows XP CD. Select Start > Run.
2. In the Run box, where D is the drive letter for the CD-ROM, type D:\i386\winnt32
and press Enter. The Welcome to the Windows XP Setup Wizard displays.
3. Choose Upgrade to Windows XP and click Next. The License Agreement page
displays.
4. Read the license agreement and click the button to accept this agreement.
5. Click Next. The Upgrading to the Windows XP NTFS File System page displays.
6. Follow the prompts and complete the upgrade. When the install is complete, the
computer will restart.
Preventive Maintenance Planning
Components of a preventive maintenance plan:
Updates to the operating system and applications
Updates to anti-virus and other protective software
Hard drive error checking
Hard drive backup
Hard drive defragmentation
Schedule Tasks
The DOS AT command launches tasks at a specified time using the command line
interface
Information about the AT command is available at this path: Start > Run > cmd
Then type AT /? at the command line.
The Windows Task Scheduler launches tasks at a specified time using a graphical
interface
Access the Windows Task Scheduler by following this path: Start > All Programs
> Accessories > System Tools > Scheduled Tasks
Examples of scheduled tasks to run
ScanDisk (Windows 2000) and CHKDSK (Windows XP) check the integrity of files
and folders and scan the hard disk surface for physical errors.
Defrag: Gathers the noncontiguous data into one place, making files run faster
Automatic Updates
An automatic update service scans the system for needed updates, and
recommends what should be downloaded and installed.
Automatic update services can setup to download and install updates as soon as
they are available or as required, and install them when the computer is next
rebooted.
Restore Point
An image of the current computer settings. If the computer crashes, the OS can roll back
to a restore point.
The restore point utility only operates on OS and application files.
Anti-virus software should be run to remove malware before creating a restore
point.
When to create a restore point:
Before updating or replacing the OS
When an application or driver is installed
Manually at any time
Backup the Hard Drive
Backup tools allow for recovery of data.
Use the Microsoft Backup Tool to perform backups.
Establish a backup strategy that will allow for the recovery of data.
Decide how often the data must be backed up and the type of backup to perform.
Windows XP uses Volume Shadow Copying, which allows users to continue to
work even as a backup is taking place.
It is only necessary to make copies of the files that have changed since the last
backup.
Types of Backups
Description
Clear
marker
Normal
Selected files and

folders
Yes
Copy
Selected files and

folders
No
Differential
Selected files and

folders that
changed since
the last backup
No
Incrementa
l
Selected files and

folders that
changed since
the last backup
Yes
Daily
Selected files and

folders that
changed during
the day
No
SELF-CHECK 1.2-2
Operating System
1. Discuss the importance of Operating system .

2. Name some of the common operating systems used nowadays.
ANSWER KEY 1.2-2

1. Operating System configures and manages hardware and it helps to connect hardware
and applications.
2. Common operating systems are MAC OS, Windows, MS-DOS and Linux.
Job Sheet 1.2-1

Title
: Installation of Operating System
Performance Objective
: Given a working personal computer you are going
to partition the hard disk in two, format in NTFS,
install Operating system & necessary drivers.
Duration 1.5 hours.
Supplies, Tools & Equipment :
Working PC
OS Installer
Drivers Software
Manuals
Steps/ Procedure:
1. Start Computer
a. Check cable connections if it is properly connected.
b. Connect the power cord to the power outlet.
c. Switch on the AVR & UPS
d. Switch on the CPU & Monitor
2. Go to CMOS setup & change boot option to CD or DVD Drive
a. Press the Del key or F1
b. On boot option select CD or DVD drive as your first boot & hard
disk in the second.
c. Save and restart the computer.
3. Install Operating System using Fresh installation.
Start your computer from the Windows XP CD-ROM. To do
this, insert the Windows XP CD-ROM into your CD drive or
DVD drive, and then restart your computer.
When you see the "Press any key to boot from CD" message,
press any key to start the computer from the Windows XP
CD-ROM.
4. Install
At the Welcome to Setup screen, press ENTER to start

Windows XP Setup.
Read the End-User License Agreement, and then press F8.
Follow the instructions on the screen to delete, create select
and format a partition where you want to install Windows
XP.
Note : Delete partition and create another two partition
using NTFS.
Follow the instructions on the screen to complete Windows
XP Setup.
Necessary Drivers.
Right click My Computer
Go to Properties
Click Hardware
Open Device Manager
Right Click the device with yellow Question mark
Click Update drivers
Select No Not at this time
Click next
Select an option if what you want the wizard to do
Click next
Wait until the driver will be installed.
Assessment Method:
Demonstration , Performance Criteria checklist
Performance Criteria Checklist 1.2-1

CRITERIA
Yes
No
Did you.
Started the computer properly
Made CD/DVD Drive as first boot option
Deleted partition/s
Created two partition
Formatted Hard disk in NTFS
Installed Operating System
Installed all necessary drivers
Applied OHS procedures.

Software Packages and Use of Application Programs
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to use Software Packages
and Application Programs.
Software is the component of a computer system which refers to the set of
instructions written in a code-that computers can understand and execute. Another
name for this set of instructions is program.
Three Types of Software
1. System Software
2. Application Software
3. Programming Language
System Software. This software tells the CPU what to do, a more common term is
Operating System (OS). The most popular OS in use for PC microcomputer is Microsofts
MS DOS. DOS for short is a collection of various programs that help control your PC.
Other operating systems are Microsoft Windows (from the early Windows 95 and 98 to
the current windows Vista, OS 2, MAC OS, Unix, Linux and Apples OS 9.
Application Software.
This is designed and written to perform specific personal,
business, or scientific processing tasks, such as payroll, processing, human resource
management, or inventory management. Common Application software are the following:
Word Processor This serves as an electronic typewriter and even more. With
word processors, the user can easily produce quality documents like memos and
reports. Popular word processors include MS Word and Word Perfect.
Spreadsheets- These are programs that simulate a paper divided into rows and
columns, where values can be placed. These are used for advanced numerical
analysis and calculations. Some of the more common spreadsheet programs are
Lotus 1-2-3 and, Ms Excel and Open Calculate.
Database Programs These serve to collect a structured collection of data, which

can later be managed and manipulated.
Presentation Software These are programs that allow users to create electronic
presentation for reports and other functions.
Desktop Publishing Software This allow the user to create page makeups and
do simple typesetting to produce various materials, such as books pamphlets,
reports, and booklets. Example of DTP software are MS Publisher, and PageMaker.
Reference Software These are electronic versions of various references such as

encyclopedia, almanacs, atlases, dictionaries, thesauri, and the like.
Graphics Programs These allow the creation and manipulation of graphics,

images, objects, and pictures. Some of the common graphics programs are
CorelDraw, Photoshop, and Computer Aided Design (CAD)
Educational Software These include tutorials and electronic lessons that give
students knowledge or training in a particular subject or skill, such as Math or
Science or in gardening or cooking.
Computer Games These are programs that simulate real games or provide
entertainment and adventure to users.
Network Software These are programs that make it possible for computers in
different areas to be connected, allowing their users to communicate with each
other.
Language Software These provide programmers with the necessary tools to

write programs and instructions to computer.
Programming Software. Programmers use this software for making computer programs.
Programming software is a tool to make software using different programming
languages.
SELF-CHECK 1.2 -3
A. TRUE OR FALSE.
Write T if the statement is true and correct and F if it is
not. Use a separate sheet of paper in answering.
______ 1. Word processors are used to create special movie effects.

______ 2. Systems software tells the CPU what to do.
______ 3. Software refers to the set of instructions that computer can understand and
execute.
______ 4. Reference software includes tutorial and electronic lessons that give students
knowledge or training in a particular subject or skill.
______ 5. Graphics Program allow the users to execute electronic presentations for
reports and other functions.
C. Discuss briefly the three types of software.
ANSWER KEY 1.2-3

A. True or False
1. False
2. True
3. True
4. False
5. False
B.
System Software tells the Central processing unit what to do.
Application Software This is designed and written to perform specific

personal, business, or scientific processing tasks, such as payroll processing, human
resource management, or inventory management.
Programming Software - to make software using different programming languages .

Peripheral Devices
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to be familiar with Peripheral Devices.
Peripheral device is any component or piece of equipment that expands a

computers input, storage, and output capabilities. Peripheral devices serve specific
purpose, enhance a computers functions, or add new service or additional resources.
1. Video Card - converts the processors output information into a video
signal that can be sent through a cable to the monitor.
2. Sound Card enhances the computers sound-generating capabilities by
allowing sound to be output Philips Screw Driver- Used to drive or fasten
positive slotted screws through speakers
3. Monitor is the display device that takes the electrical signals from the
video card and forms an image using points of colored light on the screen.
4. Speaker plays sounds transmitted as electrical signals from the sound
card.
5. Printer - an output device that produces text and graphics on paper.
6. Keyboard an input device that converts letters, numbers, and other
characters into electrical signals readable by the processors.
7. Mouse is used for inputting commands and to manipulate objects viewed
on the computer display screen.
8. Microphone - a device that converts sounds to electrical signals by means
of a vibrating diaphragm.
9. Scanner - it is an input device that reads text or illustration printed on
paper, translates the information into a form that a computer can use.
10.
Digital Camera use a light-sensitive processor chip to capture
photographic images in digital form on a small diskette inserted in the
camera or on flash memory chips.
11.
Graphic tablet objects are drawn using a pen or a puck. The puck
is technically a tablet cursor, not a mouse.
12.
Joy Stick - a hand-held control stick that allows a player to control
the movements of a cursor on a computer screen or a symbol in a video
game .
SELF-CHECK 1.2-4
A. MULTIPLE CHOICE. Write the letter of the correct answer.

1. What do you call a device converts computer output into display images?
A. Floppy disk
B. Monitor
C. Printer
D. Processor
2. Which of the following is a secondary storage device?
A. Floppy Disk Drive
B. Memory Chip
C. Printer
D. Processor
3. If you want to enhance your computers capabilities, which would you install?
A. Monitor
B. Sound Card
C. Speaker
D. Video Card
4. What part of the main circuit board would you connect a peripheral device such as
keyboard, printer or video monitor?
a. The Bus
b. Port
C. Expansion Slot
D. Cable
5. You want a hard copy of your input, which would provide you this?
A. Monitor
B. Printer
C. Speaker
D. Video Camera
ANSWER KEY 1.2-4
a) Multiple Choice.
1. a
2. c
3. d
4. b
5. c

Multimedia Systems
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to operate and use Multimedia Systems
Multimedia is the combination of different types of communication media (sound,

print, video, and so on)
Multimedia refers to computer system that lets the user access and interact with
computerized text high resolution still graphics, motion visuals, and sound. Three
elements in particular distinguish multimedia: sound, motion, and the opportunity for
interaction.
CD-ROM is the backbone of multimedia applications, a spinoff of audio CD
technology, stands for compact disk-read-only memory.
The name implies its
application. CD ROM disks are created at a mastering facilities, just as audio CDs are
created at a recording studio. The following is a sampling of available CD.
The Grolier Electronic Encyclopedia

The Oxford English Dictionary
Microsoft Bookshelf
Great Cities of the World
Sound Effects
The Animals
World Atlas
Dessert Storm and others
These days a desktop computer is usually a multimedia computer, with sound and
graphics capability.
A multimedia computer features such equipment as a fast
processor, DVD device, sound card, graphics card and speakers, and you may also wish
to have headphones and microphones. You may even wish to add scanner, sound
recorder, and digital camera.
Multimedia presentations are becoming more and more prevalent. These types of
presentations are being used not only in encyclopedia and other reference tools, but for
selling a product or teaching a new concept.
SELF-CHECK 1.2-5
1. What is multimedia? Give examples of communication media.
2. Discuss the importance of multimedia in maintaining, upgrading and
repairing our Personal Computers.
ANSWER KEY 1.2-5

1. Multimedia is the combination of different types of communication media (sound,
print, video, and so on)
Multimedia refers to computer system that lets the user access and interact with
computerized text high resolution still graphics, motion visuals, and sound. Three
elements in particular distinguish multimedia: sound, motion, and the opportunity for
interaction.
2. Since CD-ROM is the backbone of multimedia applications we now have different

software applications that help the computer technician or even the user to maintain,
upgrade, install and repair our computers.
Also to be considered the different websites from the internet thathelp us in solving and
fixing related problems.

Computer Hardware
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to familiarize Computer hardware and
enumerate its functions and uses.
HARDWARE Refers to the tangible (things you can touch) components of a computer
system. Hardware components are further divided into three groups namely
Input Devices
Output devices
System Unit
INPUT DEVICES. Performs the two most basic computing tasks: issuing commands
and entering data. Common input devices are the following:
- Keyboard is a standard input device of most computers
MOUSE
KEYBOARD
- Mouse is a hand-clicked device used for pointing. The modern mouse uses
a ball for movement and has two to three buttons.
- Trackball is like a stationary, upside down mouse.
- Joystick is an input device which is commonly used for computer games
JOYSTICK
LIGHT PEN
- Light pen a device used to draw, write, or issue commands when it touches a
specially designed screen.
OUTPUT DEVICES. After processing the data fed into computer with the use of
input devices, the information must now be outputted in a form understood by
human beings. Output devices are classified according to the output they can
produce. An output which you can hold in your hand is called hard copy. Output
types such as audio and video are referred to as soft copy. The following are output
devices used.
- Printer - - an output device that produces text and graphics on paper
NON-IMPACT PRINTER
IMPACT PRINTER
- Video Monitors The monitor, or display is used to provide soft copy output.
Video monitors are either monochrome or colored
VIDEO
MONITOR
SPEAKERS
Speakers- play sounds transmitted as electrical signals from the sound card.
Modem a device that sends and receives data over telephone lines to and from
computers.
Modem
THE SYSTEM UNIT. The system unit is the part of the computer which is
responsible for accepting and processing the data brought in by the input devices. It
also responsible for passing the resulting information to the users via the output
devices.
The Main Circuit Board - Also called the "system

the main printed circuit board in an electronic device,
contains sockets that accept additional boards. In a
computer, the motherboard contains the bus, CPU and
coprocessor sockets, memory sockets, keyboard
and supporting chips.
board," is
which
personal
MAIN CIRCUIT
BOARD
controller
Port is a connection from the main circuit board to a peripheral device such as a
keyboard, a printer or a video monitor. The port is also called an interface. Ports
are arranged at the rear of the main circuit board.
Expansion Slot is a receptacle inside a computer or other electronic system that
accepts printed circuit boards.
The Bus. is responsible for transporting electronic signals from place to place or
specific predefined routes.
The CPU The CPU is the computers processor, controller and storage device
Case and Power Supply is also known as the system unit, the case or system
cabinet is the box that houses the processor chip (CPU), the memory chips, and
the motherboard with power supply, as drive, and CD-ROM or DVD drive. It
include a power supply unit and a fan to keep the circuitry free from overheating.
POWER SUPPLY
Clock it synchronizes the operation of all parts of the PC, and provides the basic
timing signal for the CPU.
Memory The memory in a computer system is of two fundamental types: The

main memory and the secondary memory.
Memory cards
RAM-(Random Access Memory) is a group of memory chips, typically of the

dynamic RAM (DRAM) type, which function as the computer's primary workspace.
The "random" in RAM means that the contents of each byte of storage in the chip
can be directly accessed without regard to the bytes before or after it.
BIOS The BIOS (Basic Input / Output System) is a ROM chip that provide.
CMOS stores the configuration of the PC (example the password, disk type,
amount of memory installed, current time and data).
CMOS stands for
Complimentary Metal-Oxide Semiconductor.
Secondary Memory Secondary memory is where programs and data are kept for
a long term basis. Common secondary storage devices are the floppy disk and
hard disk, Compact disk or CD.
FLOPPY DISK (or diskette) is as flimsy as a sheet of paper but is protected by a

sturdy, square jacket that encases it. It has a low capacity, and is very, very slow
compared to other storage devices.
FLOPPY DISK
PROCESSOR CHIP
HARD-DISK DRIVE A hard-disk drive is a storage device that store billons of

characters of data on a nonremoveable disk platter.
HARD- DISK DRIVE
FLOPPY DRIVE
CD-ROM/DVD Drive
CD-ROM/DVD DRIVE A CD (computer disk) drive, or its more recent variant, a

DVD (digital video disk, is a storage device that use laser technology to read data
from optical disks.
VIDEO CARD is a board that is plugged into a period computer to give it display
capabilities. It connects the processors output information into a video signal
that can be sent through a cable to the monitor.
VIDEO CARD
SOUND CARD
SOUND CARD - enhances the computers sound generating capabilities by allowing

sound to be output through speakers.
MODEM A modem is a device that sends and receives data over telephone lines
to and from computers.
MODEM
IDE CABLE / FLOPPY CABLES
POWER CABLES it supplies power from the power supply to the drive. The power
cables are red, yellow and black. The yellow wire furnishes 12 volts of power, the red wire
furnishes 5 volts of power, the two black wire are ground wire for each.
IDE AND FLOPPY DISK RIBBON CABLE IDE stands for Integrate Device Electronics. It
shows how to connect an IDE cable to two devices namely the top device (master) and the
bottom device (slave).
SELF-CHECK 1.2-6
A. Identification.Label the following peripheral devices and give their functions.
1.
2.
3.
4.
5.
B. TRUE OR FALSE.
Write True if the statement is correct and False if it is wrong.
1. The main memory is a software component.

2. Processing is the manipulation by which a computer transforms data into
information.
3. The operating system is the part of the system software.
4. Input devices include the keyboard and the mouse.
5. Main memory is where programs and data are kept on along term basis.
ANSWER KEY 1.2-6

1. Modem - allows a given computer to share data or otherwise a device which let
computers exchange information
2. Mouse It is used for pointing and also to easily access other commands
3. Keyboard It is primarily used in entering and editing data
4. Speaker It play sounds transmitted as electrical signals from the sound card.
5. Monitor It displays activity inside the computer
B.True or False
1.False
2.True
3.True
4.True
5.False
LOCAL AREA NETWORKS (LANs) SYSTEMS AND CONFIGURATIONS

Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to crimp LAN cable,
configure the system and check the connectivity of your work.
A network is a group of interconnected computers, linked for the purpose of

sharing files, programs and peripherals. Through your computers or office network, you
can run programs, use printers, and edit files from other computers as if they were
located on your own.
A server is the computer on the network that manages the network resources,
such as the shared files, programs and printers.
Local-area network (LAN) is a computer network covering a small geographic area,
like a home, office, or group of buildings e.g. a school.
The majority of networking, particularly at the corporate level, is done using the
internet standard. At the center of the basic diagram of a wired network is either a hub
or a switcher and computers are connected to the hub, much like spokes of a wheel or
star. Each connection at the hub is called a port.
Three Basic Network Categories
Local Area Network- the smallest of the three network types, consists of PCs
connected together within a limited area, such as within the same building, floor or
department.
LOCAL AREA
NETWORK
Metropolitan Area Network is a network that spans no more than 50 miles. It is

design to connect LANs spanning a town or city
METROPOLITAN AREA
NETWORK
WIDE AREA NETWORK
Wide Area Network is used to distribute information thousand of miles among

thousands of users.
Network Terms:
Network Server- is a powerful computer whose sole purpose is to serve network

clients.
NETWORK SERVER
Host any computer whether mainframe, server, or even PC that acts as an

information source on a network.
Peers- mean any computer sharing the same protocol layer with another
computer.
Workstation- is any network computer that connects to and request resources

from a network
Protocol refers to the specific standards governing the sending and receiving of
data.
Types of Networks
server/client use a network operating system to manage the entire work.
Peer-to-peer - no centralized computer oversees the networks, no server, and

computers simply connect with each other in a network group to share files,
printers, and internet access.
The Basic Rule

The basic rule for network design is known as the 5-4-3 rule. It states that in a 10 Mbps.
Ethernet network:
you can have a maximum of five cable segments between any two computers
you can have a maximum of four repeaters (hubs, switches, wireless access points,
etc.) between any two computers
of the five cable segments (maximum) between any computers, only three of these
can terminate in computers.
How to wire Ethernet Cables

How to wire your own ethernet cables and connectors.
What You Need:
Required:
CAT 5 Cable - bulk Category 5, 5e or 6 cable
RJ45
Crimper for RJ45
Wire Cutters - to cut and strip the cable if necessary
Recommend:
Wire Stripper
Cable Tester
About the Cable:

Here is what the internals of the cable look like:
Internal Cable Structure and Color Coding

Inside the cable, there are 8 color coded wires. These wires are twisted into 4 pairs of
wires, each pair has a common color theme. One wire in the pair being a solid or
primarily solid colored wire and the other being a primarily white wire with a colored
stripe (Sometimes cable doesn't have any color on the striped cable, the only way to tell
is to check which other wire it is twisted around).
About the RJ45 Ends:
The RJ45 end is a 8-position modular connector that looks like a large phone plug.
There are a couple variations available.
Here is a diagram and pinout:
RJ45 Jack and Plug Pinout

Ethernet Cable Pinouts:
There are two basic cables. A straight through cable, which is used to connect to a hub
or switch, and a cross over cable used to operate in a peer-to-peer fashion without a
hub/switch. Some interfaces can cross and un-cross a cable automatically as needed,
really quite nice.
Standard, Straight-Through Wiring (both ends are the same):
RJ45 Pin
#
Wire Color
(T568A)
Wire Diagram 10Base-T Signal

1000Base-T Signal
(T568A)
100Base-TX Signal
White/Green
Transmit+
BI_DA+
Green
Transmit-
BI_DA-
White/Orange
Receive+
BI_DB+
RJ45 Pin
#
Wire Color
(T568A)

1000Base-T Signal
(T568A)
100Base-TX Signal
Blue
Unused
BI_DC+
White/Blue
Unused
BI_DC-
Orange
Receive-
BI_DB-
White/Brown
Unused
BI_DD+
Brown
Unused
BI_DD-
Straight-Through Cable Pinout for T568A

RJ45 Pin
#
Wire Color
(T568B)

1000Base-T Signal
(T568B)
100Base-TX Signal
White/Orange
Transmit+
BI_DA+
Orange
Transmit-
BI_DA-
White/Green
Receive+
BI_DB+
Blue
Unused
BI_DC+
White/Blue
Unused
BI_DC-
Green
Receive-
BI_DB-
White/Brown
Unused
BI_DD+
Brown
Unused
BI_DD-
Straight-Through Cable Pinout for T568B
Cross Over Cable (T568B):

RJ45 Pin #
(END 1)
Wire Color
Diagram End
#1
RJ45 Pin #
(END 2)
Wire Color
White/Orange
White/Green
Orange
Green
White/Green
White/Orange
Blue
White/Brown
White/Blue
Brown
Green
Orange
Diagram End
#2
RJ45 Pin #
(END 1)
Wire Color
7
8
Diagram End
#1
RJ45 Pin #
(END 2)
Wire Color
White/Brown
Blue
Brown
White/Blue
Diagram End
#2
Cross Over Cable Pinouts

+Note: The cross over cable layout is suitable for 1000Base-T operation, all 4 pairs are
crossed.
How to wire Ethernet Cables:
1. Strip off about 2 inches of the cable sheath.

2. Untwist the pairs - don't untwist them beyond what you have exposed, the more
untwisted cable you have the worse the problems you can run into.
3. Align the colored wires according to the diagrams above.
4. Trim all the wires to the same length, about 1/2" to 3/4" left exposed from the
sheath.
5. Insert the wires into the RJ45 end - make sure each wire is fully inserted to the
front of the RJ45 end and in the correct order. The sheath of the cable should
extend into the RJ45 end by about 1/2" and will be held in place by the crimp.
6. Crimp the RJ45 end with the crimper tool
7. Verify the wires ended up the right order and that the wires extend to the front of
the RJ45 end and make good contact with the metal contacts in the RJ45 end.
8. Cut the cable to length - make sure it is more than long enough for your needs.
Remember, an end to end connection should not extend more than 100m (~328ft).
Try to keep cables short, the longer the cable becomes the more it may affect
performance, usually noticable as a gradual decrease in speed and increase in
latency.
9. Repeat the above steps for the second RJ45 end.
10.
If a cable tester is available, use it to verify the proper connectivity of the
cable.
That should be it, if your cable doesn't turn out, look closely at each end and see if you
can find the problem. Usually a wire ended up in the wrong place or more commonly,
one of the wires didn't extend to the front of the RJ45 connector and is making no, or
poor contact. If you see a mistake or problem, cut the end off and start again.
SELF CHECK 1.2-7

Multiple Choices: Select the best answer of the given statement.
1. A group of interconnected computer
A. Network
B. Server
C. Workgroup
D. Sharing
2. The smallest type of network
A. Local Area network
B. Metropolitan Area Network
C. Wide Area Network
D. All of the above
3. A powerful computer whose sole purpose is to serve network clients
A. Host
B. Peers
C. Network Server
D. Workstation
4. Any network computer that connects to and request resources from a

network.
A. Host
B. Peers
C. Network Server
D. Workstation
5. Any computer whether mainframe, server or even PC that acts as an
information sources of a network
A. Host
B. Peers
C. Network Server
D. Workstation
Answer key 1.2-7

1.
2.
3.
4.
5.
A
A
C
D
A
TASK SHEET 1.2-1

Title
: Network Cable Connection
: Given the necessary tools and materials you are

going to make crossover and straight cable
connection and test the connectivity of your cable.
: UTP Cable, RJ 45
: Crimping tool
Network Hub
Working Computer with OS
Server
Internet connection
Cable Tester
Supplies
Tools/Equipment
Steps/ Procedure:
1. Prepare the necessary tools and materials
2. Use UTP Cable and 4 RJ-45 to make Straight & Cross-over
connection.
3. Follow the procedures in crimping UTP cable in Information

sheet 1.2-7
3. Check the connectivity of your cables.
4. Let your trainer check your work.
Assessment Method:
Demonstration with questioning , Performance Criteria checklist
Did you
Performance Criteria
1. Prepared all materials needed

2. Used the correct procedure in crimping RJ-45
3. Crimped cross-over & straight though connection
correctly
4. Checked the connectivity of two cables
5. Observed Safety Precautions while working
6. Used the standard color coding of cables
7.
Observed 5s before, during and after the task
YES
NO

Computer Symptoms and Diagnosis
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to Identify and diagnose
computer symptoms.
No matter how well built your PC is, and how well written its software, something
is eventually going to go wrong.
Many times, computers will get slow for seemingly no reason at all. Devices often
malfunction and system problems can arise out of nowhere. For people who rely on their
computer for business or personal use, these computer errors can be frustrating and
problematic.
One of the most important aspects of using a PC is taking care of it. Maintenance
involves keeping your hard disk in optimum working condition, checking for errors, and
backing up important files. Maintenance tasks also include adding new hardware to
your system and updating the files that control your hardware (called drivers).
Common Error Messages
As you work on your computer, there are error messages that come up. The
machine at times tries to tell you where the problem is. These messages are like
detective clues for the Help Desk.
Common Problems
1. My monitor is blacked out
2. I dont have any sound.
3. My machine is stuck and wont do anything
Checking of Peripherals
Keyboards
If our machine, when booting, gives off a constant beeping noise, it is telling that
your computer keyboard is not connected or not working.
If there is no response, check the indicator light on the keyboard.
Is there a key stuck? Gently pry off the cover and clean it with alcohol. Make sure
it is not connected to your machine when you are cleaning it.
Mouse
If your mouse starts acting erratic, it could be an insufficient memory problem.
If your mouse will only move one way, either vertically or horizontally, your mouse
may need cleaning. Shut down your machine and unplug your mouse from the
computer.
Optical mouse need cleaning of its bottom every now and then too.
Printer
Verify that the printer is working correctly by running a test print.

Unplug the printer cable from the back of the PC and try to print the printer
Reattach the printer and run another test print,
Turn off the printer and try to print to it.
What error messages appear? Turn the printer back on and run a test print
Turn off the printer and remove the ink or toner cartridge. Turn the printer back
on. Do any error messages appear? Try printing to the printer. Do any error
messages show up them?
Reinstall the ink or toner cartridge and run a test print. Remove all of the paper
from your printer and then try to print it. What error messages appear now?
A Dead PC
First check the cable

Check the wall outlet
Turn the system off and wait for a few seconds and then try again.
Reach behind the machine and see if you feel air blowing out of the power supply.
Look at the keyboard for the indicator lights being lit up as the machine boots.
Sometimes the monitor has something to do with the system acting up. Unplug
the power cord from the monitor and the wall and re plug it.
Listen to identify a beeping series if there is one.
Self Check 1.2-8

True or False: Write T if the statement is and F if the statement is False
_______1.
_______2.
_______3.
_______4.
Computer will get slow for seemingly no reason at all.

One of the most important aspects of using a PC is taking care of it.
The computer never tries to tell you where the problem is.
If your machine, when booting, give of a constant beeping noise. It is telling
that your mouse is not connected or not working.
_______5. The first step to check the dead PC is to check the cable.
Answer Key
1.
2.
3.
4.
5.
T
T
F
F
T
TASK SHEET 1.2-2
Computer Symptoms and Diagnosis

Performance Objectives
Given the following tools, materials and equipment, perform computer symptoms
and diagnosis.
You will be assessed using the criteria in the performance checklist.
Equipment, Tools, and Materials: Window system, any type of printer
Procedures:
2. Start the computer and check for error messages.
3. Check all peripheral devices
4. Check the hard disk and optical drives
5. Check the device Drivers
6. Check Application Programs
7. Run System utilities
8. Perform Test Printing.
Assessment Method:
Performance Criteria Checklist
Did you..
1. Started the computer and checked for error messages

2. Checked all peripheral devices
3. Checked Hard Disk
4. Checked optical Drives
5. Checked the device drivers
6. checked application Programs
7. Ran system utilities
8. Printed successfully
9. Attached the printer and power cable properly
10. Observed Safety precautions are carefully.
YES
NO
Information sheet 1.2-9

Disassembling & Assembling Computer System
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able disassemble and assemble
computer system.
Introduction
Computer assembly is a large part of a technician's job.
Work in a logical, methodical manner when working with computer components
Improve computer assembly skills dramatically with practice
Open the Case

Prepare the workspace before opening the computer case:
- Adequate lighting
- Good ventilation
- Comfortable room temperature
- Workbench accessible from all sides
- Avoid cluttering workbench
- An antistatic mat on the table
- Small containers to hold screws and other small parts
There are different methods for opening cases. To learn how, consult the user
manual or manufacturer's website.
Install the Power Supply
Power supply installation steps include the following:
1. Insert the power supply into the case
2. Align the holes in the power supply with the holes in the case
3. Secure the power supply to the case using the
screws
Attach Components to the Motherboard
As part of an upgrade or repair, a technician
to attach components to the motherboard, and
install the motherboard.
proper
may need
then
CPU on Motherboard
The CPU and motherboard are sensitive to electrostatic discharge so use a
grounded antistatic mat and wear an antistatic wrist strap. CAUTION: When
handling a CPU, do not touch the CPU contacts.
The CPU is secured to the socket on the motherboard with a locking assembly.
Thermal Compound
Thermal compound helps to keep the CPU cool.
To install a used CPU, clean it and the base of the heat sink with isopropyl alcohol
to remove the old thermal compound.
Follow manufacturers
recommendations
about applying the
thermal compound.
Heat Sink/Fan Assembly

The Heat Sink/Fan Assembly is a two-part cooling device.
The heat sink draws heat away from the CPU.
The fan moves the heat away from the heat sink.
The heat sink/fan assembly usually has a 3-pin power connector.
Install CPU and Heat Sink/Fan Assembly
1. Align the CPU so that the Connection 1 indicator is lined up with Pin 1 on the
CPU socket.
2. Place the CPU gently into the socket.
3. Close the CPU load plate and secure it by closing the load lever and moving it
under the load lever retention tab.
4. Apply a small amount of thermal compound to the CPU and spread it evenly.
Follow the application instructions provided by the manufacturer.
5. Line up the heat sink/fan assembly retainers to the holes on the motherboard.
6. Place the heat sink/fan assembly onto the CPU socket, being careful not to pinch
the CPU fan wires.
7. Tighten the heat sink/fan assembly retainers to secure the assembly in place.
8. Connect the heat sink/fan assembly power cable to the header on the
motherboard.
Install RAM
RAM provides temporary data storage for the CPU while the computer is operating.
RAM should be installed in the motherboard before the motherboard is placed in
the computer case.
RAM installation steps:

1. Align the notches on the RAM module to the keys in the slot and press down
until the side tabs click into place.
2. Make sure that the side tabs have locked the RAM module and visually
check for exposed contacts.
The Motherboard
The motherboard is now ready to install in the computer case.
Plastic and metal standoffs are used to mount the motherboard and to prevent it
from touching the metal portions of the case.
Install only the standoffs that align with the holes in the motherboard.
Installing any additional standoffs may prevent the motherboard from being seated
properly in the computer case.
Install Motherboard
1. Install standoffs in the computer case.
2. Align the I/O connectors on the back of the
motherboard
with the openings in the back of the case.
3. Align the screw holes of the motherboard
with the
standoffs.
4. Insert all of the motherboard screws.
5. Tighten all of the motherboard screws.
Install Internal Drives
Drives that are installed in internal bays are called
drives.
A hard disk drive (HDD) is an example of an internal
HDD installation steps:
1. Position the HDD so that it aligns with the 3.5drive bay.
2. Insert the HDD into the drive bay so that the
holes in the drive line up with the screw holes in
3. Secure the HDD to the case using the proper
Install Drives in External Bays

Drives, such as optical drives (CD and DVD) and floppy
installed in drive bays that are accessed from the front
internal
drive.
inch
screw
the case.
screws.
drives, are
of the case.
Optical drives and floppy drives store data on removable media.

Drives in external bays allow access to the media without opening the case.
Install Optical Drive

An optical drive is a storage device that reads and writes information to CDs or
DVDs.
Optical drive installation steps:
1. Position the optical drive to align with the 5.25 inch drive bay.
2. Insert the optical drive into the drive bay so that the optical drive screw holes
align with the screw holes in the case.
3. Secure the optical drive to the case using the proper screws.
Install Floppy Drive

A floppy disk drive (FDD) is a storage device that reads and writes information to a
floppy disk.
FDD installation steps:
1. Position the FDD so that it aligns with the 3.5 inch drive bay.
2. Insert the FDD into the drive bay so that the FDD screw holes align with the
screw holes in the case.
3. Secure the FDD to the case using the proper screws.
Install Adapter Cards

Adapter cards are installed to add functionality to
Adapter cards must be compatible with the
Some adapter cards:
1. PCIe x1 NIC
2. PCI Wireless NIC
3. PCIe x16 video
Install the Network Interface Card (NIC)

A NIC enables a computer to connect to a network.
a computer.
expansion slot.
adapter card
NICs use PCI and PCIe expansion slots on the motherboard.

NIC installation steps:
1. Align the NIC to the appropriate slot on the
motherboard.
2. Press down gently on the NIC until the card is
seated.
3. Secure the NIC PC mounting bracket to the case with
the appropriate screw.
Install the Wireless NIC

A wireless NIC enables a computer
to connect to a wireless network.
Some wireless NICs are installed
externally with a USB connector.
Wireless NIC installation steps:
1. Align the wireless NIC to the appropriate expansion slot on
the motherboard.
2. Press down gently on the wireless NIC until the card is
fully seated.
3. Secure the mounting bracket to the case with the appropriate
screw.
Install the Video Adapter Card
A video adapter card is the interface between a computer and a display monitor.
An upgraded video adapter card can provide
better
graphic capabilities for games and graphic
programs.
Video adapter card installation steps:
1. Align the video adapter card to the
appropriate expansion slot on the
motherboard.
2. Press down gently on the video
adapter card until the card is fully
seated.
3. Secure the video adapter card
PC mounting bracket to the case
with the appropriate screw.
Connect Internal Cables
Power cables are used to distribute electricity from the
supply to the motherboard and other components.
Data cables transmit data between the motherboard and
devices, such as hard drives.
Additional cables connect the buttons and link lights
front of the computer case to the motherboard.
power
storage
on the
Connect Power Cables

Motherboard Power Connections
The Advanced Technology Extended (ATX) main power connector has either 20 or
24 pins.
The power supply may also have a 4-pin or 6-pin Auxiliary (AUX)
power connector that connects to the motherboard.
A 20-pin connector will work in a motherboard with a 24-pin socket.
4-
Connect Power Cables

ATA Power Connectors use a 15-pin connector to connect to hard disk
drives, optical drives, or any devices that have a
SATA
power socket.
Molex Power Connectors are used by hard disk
drives
and optical drives that do not have SATA power
sockets.
CAUTION: Do not use a Molex connector

and a
SATA power connector on the same drive at the
same
time.
pin Berg Power Connector supplies power to a floppy drive.
Power
Connector Installation Steps
1. Plug the SATA power connector into the HDD.
2. Plug the Molex power connector into the optical drive.
3. Plug the 4-pin Berg power connector into the FDD.
4. Connect the 3-pin fan power connector into the appropriate fan header on the
motherboard, according to the motherboard manual.
5. Plug the additional cables from the case into the appropriate connectors according
to the motherboard manual.
PATA
Cables
Drives connect to the motherboard using data cables.
Types of data cables are PATA, SATA, and floppy disk.
The PATA cable (sometimes called a ribbon cable) is wide and flat and can have
either 40 or 80 conductors.
A PATA cable usually has three 40-pin connectors.
If multiple hard drives are installed,
the master
drive will connect to the end
connector. The
slave drive will connect to the middle
connector.
Many motherboards have two PATA
cable sockets,
which provides support for a
maximum of
four PATA drives.
SATA Cables
The SATA data cable has a 7-pin connector.
One end of the cable is connected to the motherboard.
The other end is connected to any drive that has a SATA data connector.
Floppy Drive Cables

The floppy drive data cable has a 34-pin connector and it has a stripe to denote
the location of pin 1.
One connector at the end of the cable connects to the motherboard. The other two
connectors connect to drives.
If multiple floppy drives are installed, the A: drive will connect to the end
connector. The B: drive will connect to the middle connector.
Motherboards have one floppy drive controller which provides support for a
maximum of two floppy drives.
Install Data Cables

1. Plug the motherboard end of the PATA cable into the motherboard socket.
2. Plug the connector at the far end of the PATA cable into the optical drive.
3. Plug one end of the SATA cable into the motherboard socket.
4. Plug the other end of the SATA cable into the HDD.
5. Plug the motherboard end of the FDD cable into the motherboard socket.
6. Plug the connector at the far end of the FDD cable into the floppy drive.
Re-attach Panels, Connect External Cables
Now that all the internal components have been installed and connected to the
motherboard and power supply, the side panels are re-attached to the computer
case.
The next step is to connect the cables for all computer peripherals and the power
cable.
Re-attach Side Panels

Most computer cases have two panels, one on each side.
Once the cover is in place, make sure that it is secured at all screw locations.
Refer to the documentation or manufacturers website if you are unsure about how
to remove or replace your computer case.
CAUTION: Handle case parts with care. Some computer case covers have sharp or jagged
edges.
Connect External Cables
After the case panels have been re-attached, connect the external cables to the
back of the computer.
External cable connections include:
Monitor
USB
Keyboard
Power
Mouse
Ethernet
CAUTION: When attaching cables, never force a
connection.
NOTE: Plug in the power cable after you have

other cables.
connected all
Connect External Cables

1.
2.
3.
4.
5.
6.
7.
8.
Attach the monitor cable to the video port.

Secure the cable by tightening the screws on the
Plug the keyboard cable into the PS/2 keyboard port.
Plug the mouse cable into the PS/2 mouse port.
Plug the USB cable into a USB port.
Plug the network cable into the network port.
Connect the wireless antenna to the antenna connector.
Plug the power cable into the power supply.
connector.
Boot Computer for the First Time

The BIOS is a set of instructions stored in a nonvolatile memory chip.
When the computer is booted, the basic input/output system (BIOS) will perform a
power-on self test (POST) to check on all of the internal components.
A special key or combination of keys on the keyboard is used to enter the BIOS
setup program.
The BIOS setup program displays information about all of the components in the
computer.
Identify Beep Codes

POST checks to see that all of the hardware in the computer is operating correctly.
If a device is malfunctioning, an error or a beep code alerts the technician that
there is a problem.
Typically, a single beep denotes that the computer is functioning properly.
If there is a hardware problem, the computer may emit a series of beeps.
Each BIOS manufacturer uses different codes to indicate hardware problems.
Consult the motherboard documentation to view beep codes for your computer.
BIOS Setup
The BIOS contains a setup program used to configure settings for hardware
devices.
The configuration data is saved to a special memory chip called a complementary
metal-oxide semiconductor (CMOS).
CMOS is maintained by the battery in the computer.
If this battery dies, all BIOS setup configuration data will be lost.
Replace the battery and reconfigure the BIOS settings.
BIOS Setup Program
BIOS settings are configured in the BIOS setup program.
Self Checked 1.2-9

Match the PC Components to its proper location in the motherboard.
3
1
Answer Key
1.
2.
3.
4.
5.
C
B
E
D
A
JOB SHEET 1.2-2
Title
: PC Disassembly and Assembly
Performance Objective : Given personal computer you are going to disassemble &
assemble the unit within 30 minutes.
Supplies, Tools and Materials:
A small Phillips (star) screw driver and a small flat blade screw driver).
Bond paper
Anti static wrest band
Pliers
Anti static mat
Equipment
Steps/ Procedure:
: A working PC.
1. Confirm that the hardware works...

- Does your video monitor work?
Does your PC boot?
Do your floppy drive and CD/DVD drive work?
Does the hard drive work?
Do the keyboard and mouse functioning?
2. Turn OFF the system.

NOTE : read this in its entirety before you begin
1. Discharge yourself of all static electricity by touching the PCs chassis (or the ground
screw on the receptacle.)
2. Safety NOTE!! Beware of sharp edges!!! The cheaper chassis have very sharp edges
that can cut you easily. Be very careful and take your time. Remember, SAFETY
FIRST.
3. As you remove each board and disk drive, document the information listed in the
attached Specifications document (note some parts of the spec sheets wont apply to this
lab).
3. Disassemble the Unit
Remove the External I/O Systems:

1.
2.
3.
4.
5.
Unplug all power cords, from the commercial outlet

Remove all peripherals from the system unit.
Disconnect the keyboard from the rear of the unit.
Disconnect the monitor power cable.
Disconnect the monitor signal cable (video cable) from the video adapter card.
Do the following for each card and drive removed:

Before removing a card, document any cables that are attached to the card,
noting where they go and their orientation.
Store screws properly.
Note the position of the colour strip (pin no. 1) on the cables and make a mark
for the pin no.1 if needed on the I/O card or Motherboard and on the Floppy
and the hard drive.
Remove the Storage Devices in the System Unit:

6. Remove the floppy drive.
7. Remove the hard drive.
Remove the Interface Cards (Adapter Cards):

8. Remove the video card from the expansion slot.
9. Remove other interface cards if exists.
draw a picture of the card. The drawing should accurately show-->
the shape of the board,

the connectors on the board, including the card edge connector,
the number of pins on connectors,
all jumpers and the jumper settings.
label the board with any identification that appears on the card (chip sets
or manufacturer stamps, BIOS stamps, etc...).
4. Assemble the PC
- To assemble the PC, reverse the procedure above or follow the procedures in the
information sheet Disassembling & Assembling PC.
Assessment Method:
Demonstration, Performance Criteria checklist
Performance Criteria Checklist

CRITERIA
Did you
Followed Safety procedures
Checked Hardware functionality
Observed safety used of tools and equipment in accordance with
the manufacturers instruction
Checked PPE condition in accordance with the manufacturers
instruction
Disassembled the unit properly
Removed the external I/O system
Removed the storage devices in the system
Removed interface cards
Followed the correct procedures in Assembling the PC
Ye
s
No
Booted the PC normally
LEARNING OUTCOME SUMMARY
Learning Experiences
LEARNING
OUTCOME 3
Conduct validation and testing
CONTENTS:
1. Testing Procedures
2. Cable Troubleshooting
3. Diagnostic Software
4. Device Drivers
5. Installation of Peripheral Devices
ASSESSMENT CRITERIA:
1. OH&S policies are strictly followed resulting to no lost time injury.
2. Specified testing procedures for circuit and system are carried out.
3. Installed devices/systems are protected against loss/damage in
accordance with established standard
4. Approval is obtained before any validation or testing is employed.
5. Installation proceedings, devices/systems test conforms with
specified requirements.
6. Every device system noticed to cause malfunction of the system is
removed, tested and returned to pretest condition in accordance
with the established procedures.
7. Final inspection, testing and validation are undertaken to ensure
quality performance of the system.
8. Documentation of the performed job is submitted to a laboratory
teacher following the format given.
CONDITION:
Trainees must be provided with the following:
WORKPLACE LOCATION
Tools, Materials and Equipment and Facilities
Computer Table and Chairs
Computers
Printers
Installation CDs
And other Computer Accessories
References:
Andres Sr., Antonio M. Introduction of Computer. Fully Illustrated,
Valenzuela City; May 2003 World Class Publishing and Packaging
Sto. Domingo, Josephine C.,Learning Windows XP and Internet the Easy
Way Computers - The Easy Way
EVALUATION METHOD:
Demonstration & Oral Questioning
Written Test
Validation and Testing
Learning
Outcome 3
:
Conduct
Learning Activities
1. Read information sheet 1.3-1
Testing Procedures
2.
3.
5.
6.
Special Instructions
If you have some problem on the
content of the information sheet
dont hesitate to approach your
facilitator.
If you feel that you are now

knowledgeable on the content of
the information sheet, you can
answer self check provided in the
module.
Answer self-check 1.3-1
Compare your answer to the
answer key 1.3-1. If you got 100%
correct answer in this self-check,
you can now move to the next
information sheet. If not review the
information sheet and go over the
self-check again.
Read information sheet 1.3-2
Cable Troubleshooting
facilitator.
the information sheet, you can now
do operation sheet 1.3-2 provided
in the module.
4. Answer self-check 1.3-2
you can now do task sheet 1.3-1. If
not review the information sheet
and go over the self-check again.
Do Task Sheet 1.3-1 Cable Compare your work to the checklist
and let your trainer check it. If you
Troubleshooting
got 100% correct answer in this
task, you can now move to the next
information sheet. If not review the
task again.
Read information sheet 1.3-3
Diagnostic Software
facilitator.

answer self check provided in the
module.
you can now move to the next
Information sheet. If not review the
self-check again.
Device Drivers
facilitator.
Operation Sheet provided in the
module.
you can now Perform Task Sheet. If
10. Perform
Task
Sheet
1.3-2 Compare your work to the Checklist
& let your trainer check it. If you
Device Drivers
got 100% correct answer in this
task, you can now move to the next
Information sheet. If not review the
self-check again.
Installation of Peripheral
Devices
facilitator.
perform Operation Sheet provided
in the module.
you can now Perform Task Sheet. If
13. Perform Task Sheet 1.3-3

Installation of
Peripherals, Network Devices and
other I/O Devices

Compare
your
work
to
the
Performance Checklist and let your
trainer check it. If you got 100%
correct answer in this task, you
can now take the Competency
Evaluation. If not review the
task again.
INFORMATIONSHEET 1.3-1
TESTING PROCEDURES
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able apply proper testing
procedures.
Testing Procedures
Deciding When to Test the System. Identify computer symptoms and defects
Preparing to Test the System . Its recommended that you should not plug your
computer and monitor directly to a wall outlet. Rather, you should purchase a UPS
(uninterruptible power supply). The UPS serves as a surge protector to prevent
your system from being damaged if a power spike is delivered to it and when power
will fail unexpectedly. The UPS gives you time to save your work and properly shut
down your system. If a system is turned off and back on rapidly, its probably not
good for the system. A very short power drop could mimic this effect and could be
hard on both the computer and the monitor.
Powering Up
First Time .
of
the
PC
there
is
a
positions,
0
means
of,
means on in
We turn the
and push the
the System for the

Examining the back
case, we see that
switch with two
and 1. Zero often
and
one
often
the computer world.
switch from 0 to 1
power button again
Adjusting
enter
BIOS
Plugging in the power cord to the back of
as delete, is
the case
when
the
up.
Consult
manual if you
about BIOS setup.
BIOS Settings . To
setup, a key, such
usually
pressed
system first starts
your main board
want to learn more
Replacing the Side of the Case and Bezel . Now that your system is tested and
weve visually seen that the CPU fan is spinning properly, we can shut down the
system and replace the side of the
Replacing the side of the case

This case side must be pushed toward the back of the case to
engage lugs on the case. Before closing the case, be sure no wires
or cables are near the edges where they might get pinched.
Screwing in the side of the case

Some cheaper cases have poorly tapped threads for the screws, so use only
minimal force to tighten the cover screws.
Closing the bezel

Here the lip of the bezel hits the CD-RW drive and we need to gently lift up
the CD drive to close the bezel. Dont just slam the bezel to close it. Close it
gently to be sure nothing interferes with it closing.
It also saves wear and tear if you depress the front cover latch as you close
it.. Tilt the front of the case upward to get a good grip on the latch.
Back of the side panel

If you have difficulty replacing the side of your case, examine it carefully to
see how the lugs engage the rest of the case.
SELF-CHECK 1.3-1
SEQUENCING. Arrange the following Testing Procedures in their proper order by
writing A for the first, B for the second, and so on down to the last.
______ 1. Prepare to test the system.

______ 2. Powering Up the System for the First Time
______ 3. Deciding When to Test the System
______ 4. Replacing the Side of the Case and Bezel
______ 5. Adjusting BIOS Settings
ANSWER KEY
2.
3.
4.
5.
6.
B
C
A
E
D
Cable Troubleshooting
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to troubleshoot Network
Cable.
Cable Trouble Shooting

Knowing simple troubleshooting techniques may help you correct some situations
and continue working. The main factors to keep in mind when troubleshooting are: do
not panic, take a common sense approach, and work from general to specific when
addressing the problem.
A series of troubleshooting tips are listed below.
Hardware
Make sure that the power cable is plugged in.
Some computer systems have several power cables, often one for each component.
Check each one and make sure that the plug is completely plugged in.
Be sure that all cables are connected.

Computer systems usually have several cables associated with them that are used
to connect the peripherals to the main system. Check both ends of the cables and make
sure they are plugged in securely and plugged into the correct location.
See to it that all components are switched on.
Most systems have components and peripherals attached to them and quite often
each one has its own power switch. All components must be switched on if
communication is to be established between them.
The keyboard and mouse cables are snugly connected to their ports.
The keyboard and mouse are moved every time the computer is used they can
work themselves loose over time. Check their connections.
Watch out for power outages or electrical storms.
Power outages and lightening strikes can damage your system. If lightning has
damaged your system, you very likely have a serious problem with some component in
the system. This is a good time to ask for assistance from someone who deals with these
types of problems on a regular basis. A UPS (uninterruptible power supply) should
prevent any damage from power outages and will also provide some protection from
lightning. But remember, nothing stops a direct lightning hit. The best protection is to
completely unplug the system from electrical outlets and unplug the modem connection.
Check if the network is operating and that the phone line is valid.
If your computer is not communicating, check the phone line or network cable for
a good connection. If you have a dialup connection, pick up the phone and listen for a
dial tone. If you are connected to a network, contact your network administrator.
Shutdown the system down and restart.
One of the great (and often frustrating) properties about computers is that in
many cases just turning the system off, waiting a minute and then turning it back on
will correct the problem.
Ask for assistance.
Your computer system is a significant investment and an important tool. Do not let
your pride keep you from asking for help when you need it.
If you are not sure ask!
SELF CHECK 1.3-2

TRUE OR FALSE: Write T if the statement is True and F if the statement is False.
_______1.
It is not necessary to check if all the cables are connected.
_______2.
See to it that all components are switched on.
_______3.
Power outages and lightning strikes cant damage your system.
_______4.
If your computer is not communicating, check the phone line or network

cable for good connection.
_______5.
Do not let your pride keep you from asking for help when you need it.
Answer Keys
1. F
2. T
3. F
4. T
5. T
TASK SHEET 1.3-1

Title
: Cable Testing / Troubleshooting
: At the end of the operation you are going to
perform cable testing and trouble shooting.
Supplies , Tools & Materials : Computer Unit, Automatic Voltage Regulator
(AVR), Power Cable, LAN Tester, PPE.
Equipment
: Functional Computer
Steps/ Procedure:
1. Prepare materials & Tools needed
2. Follow the procedures from the information sheet 1.3-2 on how
to test and troubleshoot Network Cable.
3. Let your Trainer check your work.
Assessment Method:
Did you
YES
NO
1. Plugged the power cable properly.

2. Connected the AVR to the Power source properly.
3. Observed safety precautions carefully.
4. Checked the fuse and the switch carefully.
5. Replaced defective devices successfully.
6. Checked and tested network cable.
7. Used testing instruments properly.
8. Apply Occupational health & safety procedures

Diagnostic Software
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to Identify and used
diagnostic software.
Diagnostic Software
The purpose of diagnostic software is simple: to test drives and diagnose potential
problems. These programs usually come with retail drives on a floppy disk, or can be
downloaded from the manufacturer's web site. In some cases a single program will
function for any of the manufacturer's drives, but in other cases a different program is
needed depending on the drive model.
If you suspect a problem with your hard disk, you should always run a diagnostic
program to check the status of the drive.
The following are the common diagnostic software .
Power-On Self Test (POST): It is built into system BIOS and it runs every time
you start up your PC automatically. It is often the best indicator of system
problems.
MEM.EXE: This simple utility, built into recent versions of DOS and also Windows
95, provides with details about memory configuration, as well as what is currently
using memory.
Microsoft Diagnostics: Better known as "MSD.EXE", this is a small DOS utility

that takes a brief inventory of the contents of a PC and shows them a text-based
format. This is very useful for seeing what disks are in the system, how much
memory is installed, and also for checking system resource usage such as LPT
ports and IRQs. It will show what type of BIOS are using and also what UART chip
have in the serial ports.
The Windows 95 Device Manager: This is the most useful tool for identifying
system configuration and resource usage information under Windows 95.
Norton System Information: This utility is similar to the Microsoft Diagnostics,

SI shows a great deal of information about what is in the PC. This program is part
of Symantec's Norton Utilities.
Microsoft ScanDisk and Norton Disk Doctor: These programs are used to check
for hard disk problems. This includes file system corruption and hard disk read
errors. They should be used when hard disk problems are suspected.
Norton Diagnostics: It includes tests of the processor and motherboard and

system memory, and will identify some types of resource conflicts.
SELF-CHECK 1.3-3
Identification.
Identify the correct Diagnostic tool or software stated below.

Use a separate sheet of paper in answering
1. This program includes file system corruption and hard disk read errors.
2. This is the most useful tool for identifying system configuration and resource
usage information.
3. A Diagnostic Software often the best indicator of system problems
4. It includes tests of the processor and motherboard and system memory, and
will identify some types of resource conflicts.
5. Known as "MSD.EXE a small DOS utility that takes a brief inventory of the
contents of a PC
ANSWER KEY # 1.3-3

1.
2.
3.
4.
5.
Microsoft Scandisk and Norton Disk Doctor

The Windows 95 Device Manager
Power-On Self Test (POST
Norton Diagnostic
Microsoft Diagnostic
Device Drivers
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to install device drivers.
Introduction:
Now that you have an operating system installed, youll need to install drivers for
your devices such as Video Cards, Network Interface Cards, Sound Cards, etc. In many
cases, if Windows recognizes the device, drivers will be installed automatically. In some
cases, generic drivers are installed and they will work fine.
Drivers are small software programs that help the operating system use or drive
the device. Whenever a device doesnt work properly, ask if the proper driver has been
installed.
Driver Installation Example: Monitor Driver
Installing the proper monitor information files is one of the small things that
purchasing a fully assembled PC
Default Monitor Driver
In the Control Panel, select.System to open the System Properties dialog box Then
select Device Manager to get a list of hardware in the PC. Finally, click Monitor, and
youll see that a generic monitor is listed.
System Properties
Installing a Sound Card Drivers

Once the sound card is installed, start the system and let the windows Plug and Play
install the sound cards drivers. After your driver is installed, make a quick trip to
Device Manager to make sure that the driver was installed correctly. . The Printer
Install Wizard is perfectly installed
Installing Other Drivers
Proceed similarly to install drivers for your other devices, such as a sound card if
you have one. Whenever a device doesnt seem to be working properly, ask if youve
installed the proper device driver or if its been done automatically. Looking for the device
under Device Manager in Windows is a good way to see if the device driver is installed.
As you can see in the figure below a question mark by Ethernet Controller in Device
Manager shows that network drivers arent yet installed.
Unrecognized Device
If your main board has built-in sound or networking, a CD that contains drivers
probably came with the main board. Place the CD into the CD drive and let Windows XP
search for the appropriate driver.
Other common drivers are LAN (Local Area Networking) driver, CD media driver,
expansion cards, keyboards, printers, USB devices and others.
Self Check 1.3-4

TRUE OR FALSE: Write T if the statement is True and F if the statement is false.
_______1.
_______2.
_______3.
_______4.
_______5.
It is not necessary to install drivers for your computer

Drivers are small software program that help the operating system use or
drive the device.
Installing the proper monitor information files is one of the small things
in purchasing a fully assembled PC.
In windows XP, windows do not recognize the newly installed device.
If proper driver was not installed, the PC wont work properly.
Answer Key
1. F
2. T
3. T
4. F
5. T
TASK SHEET 1.3-2

Title
: Device Drivers
Performance Objectives: At the end of the task the trainees are expected to
Install all necessary drivers in the given personal
computer.
Supplies, Tools, Material : Installation CD
Equipment
: Functional Computer w/peripherals
Steps/ Procedure:
Procedure in Bed Make Up
1.
2.
3.
4.
5.
Prepare necessary tools & equipment.

Start computer
Check the needed drivers to be installed.
Insert the installation CD.
Install Necessary drivers
Assessment Method:
Demonstration , Performance Criteria checklist
Did you
1. Started the system correctly.

2. Inserted the Installation CD properly.
3. Observed proper handling and safekeeping of
installation CD.
4. Followed the instructions on how to install device
drivers.
5. Installed the device drivers successfully
6. Followed OHS procedures.
YES
NO

Installation of Peripheral Devices
Learning Objective:
After reading this INFORMATION SHEET, YOU MUST be able to install different
peripheral devices.
Installation Of Peripherals
N
ote: If your computer doesnt have an operating system installed yet, you will want
to
stop after you install your mouse and keyboard, install your operating system,
and then resume the installation of your peripherals
Installing the Keyboard
1. Read and follow the manufacturers instructions
2. Determine if the keyboard uses a PS/2 or USB connector. The PS/2 connector
for keyboards is round and typically colored purple, while the USB is flat and
rectangular in shape.
3.
PS/S CONNECTOR
plugging it into the chosen port.
USB CONNECTOR
Installing the keyboard by
Note: Do not install your keyboard while your Computer is powered on

and do not unplug your keyboard while your computer is running.
Installing the Mouse
Installing a mouse is very similar to installing a keyboard. You will still find mice
with either USB or PS/2 connectivity, although most of the newer mice will use a USB
connection, especially if you are using a mouse for gaming. Just like the keyboard, you
can also use an adapter to change a USB connection to PS/2. If you are going to have a
lot of USB peripherals, you may want to consider using adapters for your mouse and
keyboard or perhaps using a USB hub for some of your peripherals. To complete the
installation, simply plug the mouse into the proper port.
Installing the Monitor
Installing a monitor (also known as a display) requires

1. Provide a free power outlet for A/C power.
2. Identifying the connection type you will use to connect the monitor to your
graphics card
3. For the best picture quality possible, use the digital DVI port on your graphics
card and display if they are available. Most graphics cards now support
multiple monitors and they typically include the adapters required to change a
DVI connection to VGA for older displays.
4. Once you have the display plugged in, simply connect it to the appropriate
connector on your video card and you are ready to go. Drivers are not typically
required for displays. but once again consult the manufacturers instructions
for details.
Installing the Speakers
1. Determine the type of speakers you are using. Perform a simple set of 2.0 or
2.1 speakers.
2. Connect the audio cable to the line-out jack of your computers sound card,
and connect the other end(s) to the speaker unless they are already hardwired
3. Plug in the power cord.
4. If you are using a full 5.1 or 7.1 surround sound system, the connections get a
bit more complicated.
5. Read the instructions that came with the speakers and sound card for full
details on this step. You can also find USB-powered speakers that have their
own sound card built in and need only be connected to power.
Installing a Webcam
Most webcams are USB-powered and simply require that you plug them in and
install their drivers. However, some cams require that the drivers be installed first, so be
sure to read the instructions that came with your webcam to avoid any problems. If you
bought a FireWire (a form of connection that is often faster than USB connections)
webcam, ensure that your computer has a FireWire port because they are not yet all that
common.
Installing the Printer
1. Make sure that you have an appropriate printer cable and, if necessary, a
separate power cable.
2. Turn off your PC and install the USB or parallel cable between the printer and
the PC.
3. Insert the ink cartridge or toner cartridge.
4. Plug in the printer and turn it on.

5. Reboot you PC.
6. Wait for Windows to see the new printer hardware and start the Printer Install
Wizard.
7. If you have an Installation CD, cancel the Printer Install Wizard and allow it to
auto play. Follow the instructions to install the printer driver.
8. After the printer has been installed, run a test print to verify that the printer is
working properly.
Installing a Scanner
Installing a scanner is almost identical to installing your printer. Again, you will
simply need to install the drivers and then plug the USB cable in the USB Port.
SELF CHECK 1.3-5

Arrange the procedures in proper order by witting A for the 1st step B for the second and
so on.
Installing the Printer
_____1.
Insert the ink cartridge or toner cartridge.
_____2.
Make sure that you have an appropriate printer cable and, if necessary, a
separate power cable.
_____3.
Wait for Windows to see the new printer hardware and start the Printer
Install Wizard.
_____4.
Plug in the printer and turn it on.
_____5.
Turn off your PC and install the USB or parallel cable between the printer
and the PC.
_____6.
After the printer has been installed, run a test print to verify that the
printer is working properly.
_____7.
Reboot you PC.
_____8.
If you have an Installation CD, cancel the Printer Install Wizard and allow
it to auto play. Follow the instructions to install the printer driver.
Answer Key
1.
2.
3.
4.
5.
6.
7.
8.
C
A
F
D
B
H
E
G
TASK SHEET 1.3-3

Title
: Installation of Peripherals, Network Devices and

other I/O Devices
Performance Objectives: Given the necessary tools, materials and
equipment, perform installation of a printer.
Peripheral, network devices and other I/O Devices
Tools, and Materials: Documentation, and an installation CD, multi-media
speaker, webcam and scanner
Equipment
: Window system without an installed printer, any
type of printer with cables
Steps/ Procedure:
1. Prepare the necessary tools and equipment
2. Start the computer.
3. Install printer
4. Install Speaker
5. Install webcam
6. Install scanner
7. Install necessary drivers
Assessment Method:
Did you
1. Installed the USB or parallel cable properly.

3. Inserted the ink or toner cartridge correctly.
3. Plugged and turned on the printer properly.
4. Rebooted the Personal Computer (PC).
5. Perfectly installed the Printer using Install
Wizard.
6.
Successfully made test print.
7.
Installed speaker
8. Installed Scanner
9. Installed Webcam
YES
NO
INSTITUTIONAL EVALUATION
EVIDENCE PLAN
TRAINEES NAME
FACILATATORS NAME
QUALIFICATION
COMPUTER HARDWARE SERVICING NC II
PROJECT-BASED
ASSESSMENT
SERVICING COMPUTER SYSTEMS AND NETWORKS
The evidence must show that the candidate
Identify hazards & risks

Maintain occupational health and safety awareness
Assess quality of received materials
Identify Computer Parts & Peripherals
Prepare hand tolls
Use appropriate hand tolls and test equipment
Plan and prepare for installation
Install equipment /device system*
Disassemble and Assemble system unit using standard procedures*
Install Operating System*
Install Necessary Drivers*
Conduct test
Test systems and networks
Apply 5s before, during & after the task.
Apply troubleshooting techniques
NOTE: *Critical aspects of competency
DEMONSTRATION WITH QUESTIONING CHECKLIST

TRAINEES NAME
TRAINERS NAME
X
X
X
X
X
X
X
X
X
X
X
X
X
x
x
Interview
Ways in which evidence will be collected:

[tick the column]
Witten Test
1. Install Computer Systems and Networks

Demonstration
UNIT OF COMPETENCY
COVERED
x
X
x
X
X
X
X
x
QUALIFICATION
UNIT OF COMPETENCY COVERED

1. Install Computer Systems and Networks
DATE OF EVALUATION
TIME OF EVALUATION
INSTRUCTIONS FOR DEMONSTRATION
Given the necessary materials, tools and equipment, the trainee must be able to perform the following
within four (4) hours
Install Computer Systems and Networks
Materials & Equipment
Observation:
/ to show if evidence is
demonstrated
Yes
No
N/A
Identify hazards & risks

Maintain occupational health and safety awareness
Assess quality of received materials
Identify Computer Parts & Peripherals
Prepare hand tolls
Use appropriate hand tolls and test equipment
Plan and prepare for installation
Install equipment /device system*
Disassemble and Assemble system unit using standard procedures*
Install Operating System*
Install Necessary Drivers*
Conduct test
Test systems and networks
Apply 5s before, during & after the task.
Apply troubleshooting techniques
INTERVIEW QUESTION CHECKLIST

QUESTIONS
1. You are preparing a computer for a dual-booting between Windows 98 and XP,
Your drives is partitioned, and Windows 98 is already installed. What should
be your next steps?
2. Give disadvantage & advantages of NTFS file system.
3. You want to setup a dual-booting system between windows 98 and windows XP.
How would you do this?
Satisfactory
response
YES
NO
4. Name one way of checking drives for errors.

5. You have configured a dual-boot system consisting of windows 98 in FAT 32
partition and Windows XP using NTFS partition. You checked your windows XP
installation and it works correctly. However, when you boot to windows 98 you
cannot see the files in the NTFS partition. What is the problem?
6. What is the problem if our machine, when booting, gives a constant
beeping noise?
7. A customer complains that his monitor is not functioning . After examining the
computer and diagnosing the defects, you notice that the problem seems to be
coming from the memory. Which component(s) should be replaced?
8. What indicated by 202 error at system startup?
9. Youve set up a network whereby each computer acts as a client and a server and
in which each user shares each others resources, including printers. What is
the correct term for such setup?
10.
After a successful upgrading to Windows 2000, what should you do with the
temporary files generated during the setup process?
Feedback to the Candidate:
The Candidates overall performance was:

Satisfactory
Not Satisfactory
Candidate Signature
Date
Assessor signature
Date
Witten Test:
MULTIPLE CHOICE.
Write the letter of the correct answer.

1. Which among the network hardware forwards data packets between Local or Wide
Area Network groups.
a. Network Hubs
c. Repeater
b. Network Switch
d. Router
2. A typical computer system consists of the following except

a. Central Processing Unit
d. Output Device
b. Input Device
e. Storage Device
c. Network Device
3. What network hardware strengthens signals and allows then to stay clear over longer
distances?
a. Network Hubs
c. Repeater
b. Network Switch
d. Router
4. Which of the following is the collection of computers and related equipment that are
connected so that data can move between them.
a. Computer System
c. Hardware
b. Network
d. Software
5. Which provides the physical link between your computer and the network
a. Network Hubs
c. Network Switch
b. Network Interface Cards
d. Router
6. What do you call a device converts computer output into display images?
a. Floppy disk
c. Printer
b. Monitor
d. Processor
7. Which of the following is a secondary storage device?
a. Floppy Disk Drive
c. Printer
b. Memory Chip
d. Processor
8. If you want to enhance your computers capabilities, which would you install?
C. Monitor
c. Speaker
D. Sound Card
d. Video Card
9. What part of the main circuit board would you connect a peripheral device such as keyboard,
printer or video monitor?
a. The Bus
c. Expansion Slot
b. Port
d. Cable
10. You want a hard copy of your input, which would provide you this?
a. Monitor
c. Speaker
b. Printer
d. Video Camera
B. TRUE OR FALSE.
Write T if the statement is true and correct and F if it is not.
______
______
______
______
1.
2.
3.
4.
Word processors are used to create special movie effects.

Systems software tells the CPU what to do.
Software refers to the set od instructions that computer can understand and execute.
Reference software includes tutorial and electronic lessons that give students
knowledge or training in a particular subject or skill.
______ 5. Graphics Program allow the users to execute electronic presentations for reports and
other functions.
______6. The main memory is a software component.

______7. Processing is the manipulation by which a computer transforms data into information.
______8. The operating system is the part of the system software.
______9. Input devices include the keyboard and the mouse.
______10. Main memory is where programs and data are kept on along term basis.
QUALIFICATION: COMPUTER HARDWARE SERVICING NC II

UNIT OF COMPETENCY: INSTALL COMPUTER SYSTEMS AND NETWORKS
SPECIFIC INSTRUCTIONS: ( For the candidate)
1. Given the necessary tools, instruments, materials, components & software, you are required to
disassemble & assemble personal computer, install the operating system and install appropriate
drivers. Test the unit and setup the network in accordance with the required criteria.
Duration: 4 hours (inclusive of questioning)
Accomplish the following before the allotted time.
1. Given the working personal computer, disassemble & assemble the system unit. Follow OHS
policies and procedures to prevent any damage to the equipment & to you.
2. Using Bootable disk delete existing & create two partitions on the hard disk and make NTFS file
system. Install Microsoft XP or any related OS. Install necessary drivers like sound card, video card,
LAN card, Printer and other peripherals.
3. Prepare all tools and equipment for network setup. Make straight-through and cross-over cables
using appropriate tools provided. Test the connectivity of your cable using LAN tester or network
hub and Other PC.
COMPETENCY EVALUATION RESULT SUMMARY

TRAINEES NAME
FACILITATORS NAME
QUALIFICATION
DATE OF EVALUATION
TIME OF EVALUATION
The Performance of the Trainee in the following assessment methods
Satisfactory
Not
[ Please Tick appropriate box]
Satisfactory
A. Written Exam
B. Interview
Facilitator
C. Demonstration
1. Install computer systems and networks
Did the trainees overall performance meet the required
evidences/standards?
Recommendation
For re-evaluation ________________________________
Qualified to take the Next Competency
General comments [Strengths/Improvement Needed]
Trainees Signature
Date:
Facilitators Signature:
Date:
ANSWER KEY
INTERVIEW POSSIBLE ANSWER
1. Install windows XP on the other partition using FAT 32.
2. NTFS is a more sophisticated file system. However, it is not compatible with DOS.
3. Partition hard disk into 2, Install 98 in the first partition then XP to the 2nd partition.
4. Check disk & defrag
5. Windows 98 is not compatible with NTFS.
6. Keyboard
7. Memory
8. Memory Problem
9. Peer to peer
10. Nothing
WRITTEN TEST
6. d
7. c
8. c
9. b
10.
11.
12.
13.
14.
15.
A. True or False
1. False
2. True
3. True
4. False
5. False
6. False
7. True
8. True
9. True
10.
False

LO5 Module 1 Installing Computer System and Networks

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

LO5 Module 1 Installing Computer System and Networks

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LO5 Module 1 Installing Computer System and Networks

Uploaded by

Copyright:

Available Formats

Sector:

INFORMATION AND COMMUNICATION TECHNOLOGY

COMPUTER HARDWARE SEVICING NC II

Technical Education and Skills Development

Active Hubs amplify or boost signals

Anti-Static A product that prevents the build up of static electricity

Hard-disk drive is a storage device that stores billions of characters of data on a

Host any computer whether mainframe, server, or even PC that acts as an

Intelligent Hubs select which path a specific signal will travel

Mainframe: A powerful multi-user computer capable of supporting many

Minicomputer: A multi-user computer capable of supporting up to hundreds of

Metropolitan Area Network is a network that spans no more than 50 miles. It

Modem - (Modulator-Demodulator) The modem is a device that allows a given

Multimedia - is the combination of different types of communication media

Network Server- is a powerful computer whose sole purpose is to serve network

Notebook computer An extremely lightweight personal computer that weighs

OHS Occupational Health and Safety

Passive Hubs simply connects various cables

Personal computer: A small, single-user computer based on a microprocessor.

Printer - It is a piece of hardware that produces a paper copy (also known as

RAM Random Access Memory, is a primary memory. This memory is used

Scanner- it is an input device that read text or illustration printed on paper,

Standalone Hubs are single products with a number of ports. It is usually

Wide Area Network used to distribute information thousand of miles among

Wireless Hubs are hubs designed for the home

Workstation- is any network computer that connects to and request resources

INFORMATION SHEET 1.1-1

Occupational Health and Safety Policy

Additional Safety tips:

Do not remove expansion cards from a computer when it is turned on.

Be sure not to mix electronic components and water.

Dont eat or drinks while working.

Self Check 1.1.1

ANSWER KEY 1.1-1

INFORMATION SHEET 1.1-2

An exploded view of a modern personal computer and peripherals:

In computing, a keyboard is an arrangement of buttons that each correspond to a function, letter, or

LAN Card is a network interface card. This

Scanner- it is an input device that read text

Printer - it is a piece of hardware that

RAM Random Access Memory, is a primary memory. This memory

Flash drive RAM that can retain data

Video Camera - camera using videotape: a

Self Check 1.1-2

ANSWER KEY 1.1-2

INFORMATION SHEET 1.1-3

A screenshot of the OpenOffice.org Writer software

Windows 7, the latest client version in the Microsoft Windows line

Mac OS X Snow Leopard desktop

A Linux distribution (Kubuntu) running the KDE 4 desktop environment.

GIMP raster graphics editor

Sound Device Driver Installer / Sound and Audio Devices A windows XP

SELF CHECK 1.1-3

ANSWER KEY 1.1-3

INFORMATION SHEET 1.1-4

System Configuration Utility overview

Process System.ini File

To perform a selective startup, follow these steps: