Hyundai l70s

L70S
TFT LCD Color Monitor
TECHNICAL SERVICE MANUAL
L70S Technical Service Manual
Safety Precaution
WARNING
Service should not be attempted by anyone unfamiliar with the necessary precautions on this
monitor.
The followings are the necessary precautions to be observed before servicing.
1. When managing this monitor , cover with shield plate to avoid to scrach on LCD surface.
2. When replacing a chassis in the cabinet, always be certain that all the protective devices are
put back in place, such as nonmetallic control knobs, insulating covers, shields, isolation
resistor capacitor network etc.
3. Before returning the monitor to the customer, always perform an AC leakage current check
on the exposed metallic parts of the cabinet, such as signal connectors, terminals, screw
heads, metal overlays, control shafts etc, to be sure the monitor is safe to operate without
danger of electrical shock.
General Information
1. Description
This 17" LCD color display monitor is operated in R, G, B drive mode input.
2. Operating instructions
2-1. Front
Power Switch , Menu, Select, Down, Up, DPMS (Power) LED
2-2. Rear
Input connector (AC & Signal Cable)
2-3. OSD Controls
H/V Position, Clock Phase, Brightness, Contrast, Recall, Color Control, Language, Auto
Adjust, Miscellaneous, Audio control, Auto Color
3. Electrical Characteristic
3-1. Power Supply
AC/DC - Input Voltage : 90V~264V
Input Current : 1.0 A Max
Input Ferquency : 50 ~ 60Hz
- Output Voltage 12V/5V
Output Current 2A/1.5A
3-2. Video Input Signal
Level : 0.7 Vp-p analog signal(at 75 ohm termination to ground)
Polarity : Positive
3-3. Horizontal Synchronization Signal
Level : TTL High : 2.4V min
Low : 0.4V max
Polarity : - or +
Frequency : 31kHz ~ 80kHz
3-4. Vertical Synchronization Signal
Level : TTL High : 2.4V min
Low : 0.4V max
Polarity : - or +
Frequency : 56Hz ~ 75Hz
--1--
Control Description
Front View
Power Switch / LED Indecator
Support Modes
NO
Resolution
H Frequency
(kHz)
V Frequency
(Hz)
H
Polarity
V
Polarity
Dot Clock
(MHz)
720 x 400
31.5
70.1
28.322
640 x 480
31.5
59.9
25.175
640 x 480
37.5
75.0
31.500
800 x 600
37.9
60.3
40.000
800 x 600
46.9
75.0
49.500
1024 x 768
48.4
60.0
65.000
1024 x 768
56.5
70.1
75.000
1024 x 768
60.0
75.0
78.750
1280 x 1024
63.900
60.000
108.00
10
1280 x 1024
79.976
75.025
135.00
--2--
Video Input Signal

Recommended signal are shown below
Video Signal
Video level : 0 to 700mV
Polarity : positive
Video Input : RGB separated
Analog level
Sync input : H-Sync(TTL level)
V-Sync (TTL level)
Waveform
Video input(R.G.B)
255
700mV
254
253
252
251
Signal: 256 level gray

scale
Linear stepping:
(2.73mV ~ 256 Steps)
4
3
2
1
0
0mV
H-Sync
V-Sync
ACTIVE (T4)
ACTIVE (T4)
Front Porch
(T5)
Period (T1)
Back Porch (T3)
Sync Width (T2)
Front Porch
(T5)
--3--
Period (T1)
Back Porch (T3)
Sync Width (T2)
Video Input Terminal

A 15 Pin D-sub connector is used as the input signal connector
Pin and input signals are shown in the table below.
Pin Description
SEPARATE SYNC/
DDC 1/2B
SIGNAL
PIN NO.
RED
GREEN
BLUE
GND
RETURN
RED GROUND
GREEN GROUND
BLUE GROUND
N.C
10
LOGIC GROUND
11
GROUND
12
SDA
13
H-SYNC(TTL)
14
V-SYNC(VCLK)
SCL
15
D-Sub miniature connector
--4--
Connecting with External Equipment

Cautions
Be sure to turn off the power of your computer before connecting the monitor.
LINE OUT
--5--
Theory of Operation
1. AC/DC INVERTER
Input voltage :
Input current :
Output current :
Frequency(switching) :
Output power :
On/off control voltage :
DC 12V
2.0A(Max)
6.5mArms(TYP)
47KHz(Max)
18W(TYP)
5.0V
2. AC/DC ADATOR
This display device shall maintain the specified per formances in the range de scribed
below
Frequency : 50/60Hz
Voltage : 90 - 264Vac RMS
The following consumption requirments shall be met:
Power Consumption : 35W(typ)
Current consumption : < 1.0 Aac RMS
Output Specification:
output1 : 12V/2A
output2 : 5V/1.5A
3. Audio System
This monitor has a audio system including two micro loudspeakers.
Each of two micro loudspeakers has a 2W(Max) output power.
This system also supports a headphone(earphone) output.
- Auto Signal Input : < 600mVp-p(Max.)
- Auto Amplifiers
2W+2W Amplifier with DC Volume Control (for two micro loudspeakers)
RL=8 @THD=10% Vcc=14V (min. 10V, max. 18V)
Dual-Audio Power Amplifier (for a headphone output)
RL=32 @THD=10% Vcc=4.5V (min. 1.8V, max. 15V)
- Speaker
Micro Loudspeaker Spec.
15% at 1.0V 1.5KHz
Normal impedance 8
Resonance Freq. 550Hz +/- 110Hz at 1.0V
Freq. Range fo ~ 20KHz
Power Rating Normal 1.0W/Peak 2.0W
4. DPMS MODE
Status
Signal
H-Sync V-Sync Video
on
Pulse
Pulse Active
off
No
Pulse
No
Pulse
Blank
Power
Consumption
Recovery
Time
LED
Indicator
35W(typ)
Green
Within 3
Sec
Orange
1W (TYP) 230V AC
--6--
On Screen Controls & LED Indicator

The menu for screen setting adjustment is located in the OSD and can be viewed in one of
five languages OSD feature andmain funcrions are as follows:
1280x1024
H:63.9
V:60.0
BRIGHTNESS
he OSD adjustments available to you are listed below.

BRIGHTNESS
Adjust the brightness of the screen.
CONTRAST
Adjust the contrast of the screen.
COLOR CONTROL
Color temperature affects the tint of the image. With lower color
temperatures the image turns reddish and with higher temperatures
bluish.
There are three color settings available: Mode 1(9300K), Mode 2(6500K) or USER. With
the USER setting you can set individual values for red, green and blue.
POSITION
H POSITION
Adjusts the horizontal position of the entire screen image.
V POSITION
Adjusts the vertical position of the entire screen image.
--7--
CLOCK PHASE
PHASE
Adjust the noise of the screen image.
CLOCK
Adjust the horizontal size of the entire screen image.
MISCELLANEOUS
RECALL
Recall the saved color data.
OSD TIMER
You can set the displayed time of OSD Menu window on the screen by using this
adjustment.
OSD POSITION
Adjust the OSD menu's horizontal or vertical position on the screen.
AUTO COLOR
Optimum color setting is auto programmed for users convenience.
LANGUAGE
You can select the language in which adjustment menus are displayed.
The following languages are available : English, French, German, Italian,
Spanish, Swedish, Finnish, Danish, Portuguese, Dutch and Japanese or chinese.
AUDIO
VOLUME
Adjust the audio volume level.
AUDIO
This menu is used to choose audio on or off.
AUTO ADJUST
You can adjust the shape of screen automatically at the full screen pattern.
--8--
Getting Fine Picture

Step 1. At first Display, a full screen, such as, Window's background or "H" character should
be achieved by using Editor (ex: Notepad. exe)
Step 2. Adjust the screen to the center of the Display(LCD), by using the top and bottom
display controls. (i.e.Using V-Position Adjust menu)
Step 3. Adjust the screen to the center of the Display(LCD), by using the right and left
display controls. (i.e.Using Clock and H-Position adjust menu)
Step 4. Adjust the Clock-phase until the "H" Character displays clear.
Step 5. Using the Contrast. Brightness, and Color Control menu, set the color to your
preference.
Step 6. When you finish the adjustment, you can save your settings by pressing on the menu
until the OSD screen has disappeared.
Factory Setting & EEPROM Initialization Method
Factory Setting Method
- Connect the signal cable and power cable to the LCD monitor.
- Press Power switch with pressed MENU key.(Menu key + Power key).
- Then, a User can change the factory setting value in OSD menu.
- Save changed value and Turn off the power s/w.
- Turn on the power, adjust the screen.
--9--
Specification
SIZE
Dot Pitch
LCD Module
Brightness
Response Time
Signal
17 Viewable diagonal
0.264mm
260 cd/m2 (TYP)
16m- sec (Typ)
R.G.B Analog
Input
Connector
15 pin D-SUB Connector
H-Freq
31.0kHz ~ 80.0kHz
V-Freq
56.0Hz ~ 75Hz
SYNC
Display
Area
337.92(H)X270.336(V)mm
Color
262K Colors
1280 X 1024 @ 75Hz
Resolution
Video Bandwidth
Contrast,Brightness, Position, Auto Color,
User Control
&
OSD Control
Clock Phase, Color Control, Language,

Auto Adjust, Miscellaneous, Audio Control
Power Management
Plug & Play
Safety &
Regulation
135MHz
VESA DPMS Standard

VESA DDC 1/2B
EMC
FCC CLASS B , CE , VCCI
Safety
cULus, CE, TUV-GS, SEMKO
Ergonomi
TCO99
Operating
5 to 35 C
Storage
- 5 to 45 C
Temperature
Operating
30 to 80%(Non-condensing)
Humidity
Storage
5 to 90%(Non-condensing)
unpacked
3.8Kg
packed
5.0Kg
Weight
Dimension(WXHXD mm)
372.5 X 398 X 185 mm
* Specification is subject to change without notice for performance improvement.
--10--
Critical Parts Specification

1. LCD Module
M170EN05(LTM170EU-L01, HT17E12-100 is a a-si TFT active matrix color liquid crystal
comprising amorphous silicon TFT attached to each signal electrode, a driving circuit and a
backlight.
M170EN05(LTM170EX-L01, HT17E12-100 has a built-in backlight display area contains
1280X1024 pixels and can display full color (262K colors)
Display area
337.92(H)X270.336(V)mm
Drive system
a-si TFT
Display color
262K Colors
Number of Pixel
1280X1024
Pixel arrangement
RGB vertical strip
Pixel pitch
0.264(H)X0.264(V)mm
Contrast Ratio*
450:1
Viewing angle*
Horizontal:
70 degree, 70 degree
Vertical:
70 degree, 70 degree
Response time*
16ms(Typ)
Luminance*
260cd/m2(Typ)
Signal system
Digital RGB signals, Sync signals(H, V-Sync),
Dot clock(DCLK) , DE(Data Enable)
Supply voltage
5V
Backlight
Edge light type: Four colt cathode fluorescent lamps
power consumption
19.6W(TYP) CCFL
*: only M170EN05
Type
Vendor
Au Optronics
M170EN05
SamSung
LTM170EU-L01
Hydis
HT17E12-100
--11--
2) CONNECTIONS
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components
Connector Name / Designation
Interface Connector / Interface card
Manufacturer
JAE or compatible
Type Parts Number
FI-X30S-HF
Mating Housing Part Number
FI-X30S-H
Connector Name / Designation
Lamp Connector / Backlight lamp
Manufacturer
JST
Type Parts Number
BHR-04VS-1
Mating Type Part Number
SM04(4.0)B-BHS-1-TB
3) Signal Pin
Pin#
Signal Name
Pin#
Signal Name
Rxo0-
Rxo0+
Rxo1-
Rxo1+
Rxo2-
Rxo2+
GND
RxoC-
RxoC+
10
Rxo3-
11
Rxo3+
12
RxE0-
13
RxEo+
14
GND
15
RxE1-
16
RxE1+
17
GND
18
RxE2-
19
RxE2+
20
RxEC-
21
RxEC+
22
RxE3-
23
RxE3+
24
GND
25
NC
26
NC
27
NC
28
Power
29
Power
30
Power
--12--
4) Signal Description
The module using a pair of LVDS receiver SN75LVDS82 (Texas Instruments) or compatible.
LVDS is a differential signal technology for LCD interface and high speed data transfer
device. Transmitter shall be SN75LVDS83(negative edge sampling)or compatible. The first
LVDS port(RxOxxx)transmots odd pixels while the second LVDS port(RxExxxx)transmits
even pixels.
PIN #
DESCRIPTION
SIGNAL NAME
RxO0-
Negative LVDS differential data input (odd data)
RxO0+
Positive LVDS differential data input (odd data)
RxO1-
RxO1+
RxO2-
Negative LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)
RxO2+
Positive LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)
GND
RxOC-
Negative LVDS differential clock input (odd clock)
Power Ground
RxOC+
Positive LVDS differential clock input (odd clock)
10
RxO3-
11
RxO3+
12
RxE0-
Negative LVDS differential data input (Even clock)
13
RxE0+
Positive LVDS differential data input (Even data)
14
GND
Power Ground
15
RxE1-
16
RxE1+
Negative LVDS differential data input (Even data)
17
GND
Power Ground
18
RxE2-
19
RxE2+
20
RxEC-
Negative LVDS differential clock input (Even clock)
21
RxEC+
Positive LVDS differential clock input (Even clock)
22
RxE3-
23
RxE3+
24
GND
25
NC
26
NC
27
NC
28
POWER
29
POWER
Power
POWER
Power
30
Power Ground
Power
Note : Input signals of odd and even clock shall be the same timing.
LVDS DATA Name
DESCRIPTION
DSP
Display Timing : When the signal is high, the pixel data shall be valid to be displayed
V-S
Vertical Sync : Both Positive and Negative polarity are acceptable
H-S
Horizontal Sync : Both Positive and Negative polarity are acceptable
--13--
MST9111
GENERAL DESCRI PTION

The MST9111 is a high performance, and fully integrated graphics processing IC solution for LCD
monitors with resolutions up to SXGA. It is configured with an integrated triple-ADC/PLL, a high qualit
scaling engine, an on-screen display controller, a built-in output clock generator, and LVDS displa
interface. To further reduce system costs, the MST9111 also integrates intelligent power managemen
control capability for green-mode requirements and spread-spectrum support for EMI management.
FEATURES
High-quality zoom and shrink scaling engine

(Compatible with VGA thru SXGA)
Integrated 8-bit triple-ADC/PLL
On-screen display controller (OSD)
Support single-RGB inputs
Built-in LVDS transmitter
Support composite sync and SOG separator
Programmable 10-bit gamma correction
Integrated Brightness & Contrast control
adjustment
Support PWM backlit intensity control
Support sRGB function
Green PC and low EMI features
Low standby power mode (< 5mA)
High-Performance Scaling Engine
Programmable shrink/zoom capabilities

High-quality scaling for all VESA and IBM mode
to fit screen
Variable sharpness control
Analog RGB Compliant Input Port
Supports up to SXGA at 85Hz

Supports Composite Sync and SOG
(Sync-on-Green) separator
Auto-Detection/Tune
Auto input signal format (SOG, Composite,
Separated HSYNC, VSYNC, and DE), and input
mode (all VESA & IBM modes w/ resolution and
polarity) detection
Auto-tuning function including phasing,
positioning, offset, gain, and jitter detection
Smart screen-fitting
--14--
On-Screen OSD Controller

Built-in OSD generator with 226 character font
programmable RAM
Internal OSD rotation degree of 90 and 270
Gradient color function
Pattern generator for production test
Support OSD MUX and alpha blending capability
LVDS Display Interface

Dual pixel with max. output LVDS clock rate of 85
MHz
Support 2 data output formats: Thine & TI data
mappings
Compatible with TIA/EIA
With 6/8 bits options
Reduced swing for LVDS for low EMI
External Connection/Component
Built-in DDC circuit
PIN DIAG RAM
24LC08
8
VCC
A0
24C08 7
or
3 24LC08 6
WP
A1
SCL
A2
SDA
VSS
A0
A1
A2
VSS
4
Dual-In-Line
package
A0
A1
A2
VSS
VCC
24C08 7
or
3 24LC08 6
WP
SCL
SDA
SO package
(M8)
8
24C08
or
24LC08
VCC
WP
SCL
SDA
TSSOP
Pin Name
A0, A1
A2
Vss
SDA
SCL
WP
Vcc
N.C.
Device Address inputs
Ground
Data I/O
Clock input
Write Protect
+ 5 V or + 3 V
3.0 ABSOLUTE MAXIMUM RATINGS

Storage Temperature................................-65C to + 125C
Voltage with Respect to Ground.................-0.3 to + 6.5 V
NOTE: These are STRESS rating only. Appropriate conditions for operating these devices given elsewhere
may permanently damage the part. Prolonged exposure to maximum ratings may affect device reliability.
4.0 OPERATING CONDITIONS

Temperature under bias: MTV24C08/24LC08.......0C to + 70C
MTV24C08/24LC08-I.....-40C to + 85C
--16--
5.0 ELECTRICAL CHARACTERISTICS

DC ELECTRICAL CHARACTERISTICS
(Vcc =5V +/- 10% ,MTV24C08/24LC08
Symbol
ICC1
ICC2
ISB
IIL
IOL
VIL
VIH
VOL1
VOH1
VOL2
VOH2
VLK
Parameter
F
Vcc =3V +/- 10% ,24LC08)
MTV24C08/
24LC08
Min
Max
10
Conditions
SCL = 100KHZ
CMOS Input Levels
Operating Current
(Program)
Operating Current
(Read)
Standby Current
SCL = 100KHZ
CMOS Input Levels
SCL = SDA = 0 V
Input Leakage
VIN = 0 V to VCC
Output Leakage
VOUT = 0 V to Vcc
mA
-1
-1
-0.1
10
+1
+1
0.15 VCC
VCC +0.2
0.8VCC
VCC+0.2
2.4
VCC-0.2
Default
0.4
0.2
A
A
A
V
V
V
V
V
V
V
IOL = 10uA CMOS
Output High Voltage
IOH = -10uA CMOS
VCC-0.2
VCC Lockout Voltage
Programming Command
Can Be Executed
Default
IOL = 2.1mA TTL
Output High Voltage
IOH = -400uA TTL
mA
Output Low Voltage
Output Low Voltage
Units
Max
8
10
+1
+1
0.8
0.4
0.2
Input High Voltage
Min
-1
-1
-0.1
2
2.4
Input Low Voltage
24LC08
6.0 SWITCHING CHACTERISTICS (Under Operating Conditions )

AC ELECTRICAL CHARACTERISTICS
Vcc =3V +/- 10% ,24LC08)
(Vcc =5V +/- 10% , MTV24C08 F
(Vcc =5V +/- 10% , MTV24C08 Fast Mode)
Parameter
Symbol
Clock frequency
Clock high time
Clock low time
SDA and SCL rise time
SDA and SCL fall time
START condition hold time
START condition setup time
Data input hold time
Data input setup time
STOP condition setup time
Output valid from clock
Bus free time
Data out hold time
Input filter spike suppression
(SDA and SCL pins)
Write cycle time
Fscl
Thigh
Tlow
Tr
Tf
Thd:Sta
Tsu:Sta
Thd:Dat
Tsu:Dat
Tsu:Sto
Taa
Tbuf
Tdh
MTV24C08/
24LC08
Min
Max
0
100
4000
4700
1000
300
4000
4700
250
4000
300
3500
4700
300
MTV24C08
(Fast Mode)
Min
Max
400
600
1200
300
300
600
600
100
600
100
900
1200
50
Units
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Tsp
100
50
ns
Twr
10
10
ms
--17--
CAPACITANCE TA= 25C , f=250KHZ

Symbol
CO
Parameter
Output capacitance
Max
5
Units
pF
pF
UT
CIN
Input capacitance
A.C. Conditions of Test

Input Pulse Levels
Input Rise and Fall times
Input and Output Timming level
Output Load
Vcc x 0.1 to Vcc x 0.9

10 ns
Vcc x 0.5
1 TTL Gate and
CL = 100pf
--18--
RC1117X2.5
RC1117
1A Adjustable/Fixed Low Dropout Linear Regulator
Features
Description
The RC1117 and RC1117-2.5, -2.85, -3.3 and -5 are low

dropout three-terminal regulators with 1A output current
capability. These devices have been optimized for low voltage
where transient response and minimum input voltage are
critical. The 2.85V version is designed specifically to be
used in Active Terminators for SCSI bus.
Low dropout voltage

Load regulation: 0.05% typical
Trimmed current limit
On-chip thermal limiting
Standard SOT-223, TO-263, and TO-252 packages
Three-terminal adjustable or fixed 2.5V, 2.85V, 3.3V, 5V
Current limit is trimmed to ensure specified output current

and controlled short-circuit current. On-chip thermal limiting
provides protection against any combination of overload and
ambient temperatures that would create excessive junction
temperatures.
Applications
Active SCSI terminators

High efficiency linear regulators
Post regulators for switching supplies
Battery chargers
5V to 3.3V linear regulators
Motherboard clock supplies
Unlike PNP type regulators where up to 10% of the output

current is wasted as quiescent current, the quiescent current
of the RC1117 flows into the load, increasing efficiency.
The RC1117 series regulators are available in the industrystandard SOT-223, TO-263 (D2PAK), and TO-252 (DPAK)
power packages.
Typical Applications
RC1117
VIN = 3.3V
VIN
VOUT
10 F
+
R1
124
ADJ
1.5V at 1A
2 F
R2
24.9
VOUT = VREF(1 + R2/R1) + IAdj R2
RC1117-2.85
VIN = 5V
VIN
+VOUT
10 F
2.85V at 1A
22 F
GND
--19--
Pin Assignments
Front View
Tab is
VOUT
Tab is
VOUT
Tab is
VOUT
IN
OUT
ADJ/GND
ADJ/
GND
OUT
IN
4-Lead Plastic SOT-223

JC = 15 C/W*
ADJ/
GND
IN
3-Lead Plastic TO-252

JC = 3 C/W*

JC = 3 C/W*
*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane., JA can vary from
30C/W to more than 50C/W. Other mounting techniques may provide better thermal resistance than 30C/W.
Absolute Maximum Ratings

Parameter
Min.
Max.
Unit
7.5
125
-65
150
300
VIN
Operating Junction Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.)
--20--
Electrical Characteristics
Operating Conditions: VIN 7V, TJ = 25C unless otherwise specified.
The denotes specifications which apply over the specified operating temperature range.
Parameter
Conditions
Reference Voltage, VREF3
1.5V (VIN - VOUT)

10mA IOUT 1A
Output Voltage
10mA IOUT 1A
RC1117-2.5, 4V VIN 7V
RC1117-2.85, 4.35V VIN 7V
RC1117-3.3, 4.8V VIN 7V
RC1117-5, 6.5V VIN 7V
5.75V,
Line Regulation1,2
(VOUT + 1.5V)
Load Regulation1,2
(VIN VOUT) = 2V, 10mA
Dropout Voltage
Current Limit
VIN
Min.
Typ.
Max.
Units
1.225
(-2%)
1.250
1.275
(+2%)
2.450
2.793
3.234
4.900
2.5
2.85
3.3
5.0
2.550
2.907
3.366
5.100
V
V
V
V
7V, IOUT = 10mA

IOUT
1A
VREF = 1%, IOUT = 1A

(VIN VOUT) = 2V
1.1
Adjust Pin Current, IAdj3

Adjust Pin Current Change3
1.5V (VIN VOUT)

10mA IOUT 1A
5.75,
Minimum Load Current
1.5V
5.75
Quiescent Current
VIN = VOUT + 1.25V
Ripple Rejection
f = 120Hz, COUT = 22 F Tantalum,

(VIN VOUT) = 3V, IOUT = 1A
Thermal Regulation
TA = 25 C, 30ms pulse
(VIN VOUT)
Temperature Stability
0.005
0.2
0.05
0.5
1.100
1.200
1.5
35
120
0.2
13
10
60
mA
72
0.004
dB
0.02
0.5
Long-Term Stability
TA = 125 C, 1000hrs.
RMS Output Noise

(% of VOUT)
TA = 25 C, 10Hz
0.03
10kHz
mA
%/W
%
1.0
0.003
Thermal Resistance, Junction SOT-223

to Case
TO-252, TO-263
15
C/W
C/W
Thermal Shutdown
155
10
Junction Temperature
Thermal Shutdown
Hysteresis
Notes:
1. See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are
measured at a constant junction temperature by low duty cycle pulse testing.
2. Line and load regulation are guaranteed up to the maximum power dissipation (18W). Power dissipation is determined by
input/output differential and the output current. Guaranteed maximum output power will not be available over the full input/
output voltage range.
3. RC1117 only.
--21--
RC1117-3.3
1A Adjustable/Fixed Low Dropout Linear Regulator
Features
Description
The RC1117 and RC1117-2.5, -2.85, -3.3 and -5 are low

dropout three-terminal regulators with 1A output current
capability. These devices have been optimized for low voltage
where transient response and minimum input voltage are
critical. The 2.85V version is designed specifically to be
used in Active Terminators for SCSI bus.
Low dropout voltage

Load regulation: 0.05% typical
Trimmed current limit
On-chip thermal limiting
Standard SOT-223, TO-263, and TO-252 packages
Three-terminal adjustable or fixed 2.5V, 2.85V, 3.3V, 5V
Current limit is trimmed to ensure specified output current

and controlled short-circuit current. On-chip thermal limiting
provides protection against any combination of overload and
ambient temperatures that would create excessive junction
temperatures.
Applications
Active SCSI terminators

High efficiency linear regulators
Post regulators for switching supplies
Battery chargers
5V to 3.3V linear regulators
Motherboard clock supplies
Unlike PNP type regulators where up to 10% of the output

current is wasted as quiescent current, the quiescent current
of the RC1117 flows into the load, increasing efficiency.
The RC1117 series regulators are available in the industrystandard SOT-223, TO-263 (D2PAK), and TO-252 (DPAK)
power packages.
Typical Applications
RC1117
VIN = 3.3V
VIN
VOUT
10 F
+
R1
124
ADJ
1.5V at 1A
2 F
R2
24.9
VOUT = VREF(1 + R2/R1) + IAdj R2
RC1117-2.85
VIN = 5V
VIN
2.85V at 1A
+VOUT
10 F
22 F
GND
--22--
Pin Assignments
Front View
Tab is
VOUT
Tab is
VOUT
Tab is
VOUT
IN
OUT
ADJ/GND
ADJ/
GND
OUT
IN
4-Lead Plastic SOT-223

JC = 15 C/W*
ADJ/
GND
IN

JC = 3 C/W*

JC = 3 C/W*
*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane., JA can vary from
30C/W to more than 50C/W. Other mounting techniques may provide better thermal resistance than 30C/W.

Parameter
Min.
Max.
Unit
7.5
125
-65
150
300
VIN
Operating Junction Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.)
--23--
Electrical Characteristics
Operating Conditions: VIN 7V, TJ = 25C unless otherwise specified.
The denotes specifications which apply over the specified operating temperature range.
Parameter
Conditions
Reference Voltage, VREF3
1.5V (VIN - VOUT)

10mA IOUT 1A
Output Voltage
10mA IOUT 1A
RC1117-2.5, 4V VIN 7V
RC1117-2.85, 4.35V VIN 7V
RC1117-3.3, 4.8V VIN 7V
RC1117-5, 6.5V VIN 7V
5.75V,
Line Regulation1,2
(VOUT + 1.5V)
Load Regulation1,2
(VIN VOUT) = 2V, 10mA
Dropout Voltage
Current Limit
VIN
Min.
Typ.
Max.
Units
1.225
(-2%)
1.250
1.275
(+2%)
2.450
2.793
3.234
4.900
2.5
2.85
3.3
5.0
2.550
2.907
3.366
5.100
V
V
V
V
7V, IOUT = 10mA

IOUT
1A
VREF = 1%, IOUT = 1A

(VIN VOUT) = 2V
1.1
Adjust Pin Current, IAdj3

Adjust Pin Current Change3
1.5V (VIN VOUT)

10mA IOUT 1A
5.75,
Minimum Load Current
1.5V
5.75
Quiescent Current
VIN = VOUT + 1.25V
Ripple Rejection
f = 120Hz, COUT = 22 F Tantalum,

(VIN VOUT) = 3V, IOUT = 1A
Thermal Regulation
TA = 25 C, 30ms pulse
(VIN VOUT)
Temperature Stability
0.005
0.2
0.05
0.5
1.100
1.200
1.5
35
120
0.2
13
10
60
mA
72
0.004
dB
0.02
0.5
Long-Term Stability
TA = 125 C, 1000hrs.
RMS Output Noise

(% of VOUT)
TA = 25 C, 10Hz
0.03
10kHz
mA
%/W
%
1.0
0.003
Thermal Resistance, Junction SOT-223

to Case
TO-252, TO-263
15
C/W
C/W
Thermal Shutdown
155
10
Junction Temperature
Thermal Shutdown
Hysteresis
Notes:
1. See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are
measured at a constant junction temperature by low duty cycle pulse testing.
2. Line and load regulation are guaranteed up to the maximum power dissipation (18W). Power dissipation is determined by
input/output differential and the output current. Guaranteed maximum output power will not be available over the full input/
output voltage range.
3. RC1117 only.
--24--
SI4435
PD- 93768A
Si4435DY
HEXFET Power MOSFET
-
Ultra Low On-Resistance

P-Channel MOSFET
Surface Mount
Available in Tape & Reel
A
D
VDSS = -30V
RDS(on) = 0.020
T o p V ie w
Description
HEXFET
These P-channel
Power MOSFETs from
International Rectifier utilize advanced processing
techniques to achieve the extremely low on-resistance per
silicon area. This benefit provides the designer with an
extremely efficient device for use in battery and load
management applications..
The SO-8 has been modified through a customized
leadframe for enhanced thermal characteristics and
multiple-die capability making it ideal in a variety of power
applications. With these improvements, multiple devices
can be used in an application with dramatically reduced
board space. The package is designed for vapor phase,
infrared, or wave soldering techniques.
SO-8

Parameter
VDS
ID @ TA = 25C
ID @ TA= 70C
IDM
PD @T A = 25C
PD @T A = 70C
VGS
TJ, TSTG
Drain- Source Voltage

Continuous Drain Current, VGS @ -10V
Continuous Drain Current, VGS @ -10V
Pulsed Drain Current
Power Dissipation
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Junction and Storage Temperature Range
Max.
Units
-30
-8.0
-6.4
-50
2.5
1.6
0.02
20
-55 to + 150
W/oC
V
oC
Max.
Units
Thermal Resistance
Parameter
RJA
Maximum Junction-to-Ambient
50
--25--
C/W
Si4435DY
Electrical Characteristics @ TJ = 25C (unless otherwise specified)
V(BR)DSS/TJ
Parameter
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
RDS(on)
Static Drain-to-Source On-Resistance
VGS(th)
gfs
Gate Threshold Voltage

Forward Transconductance
V(BR)DSS
IDSS
IGSS
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
Ciss
Coss
Crss
Drain-to-Source Leakage Current

Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Min.
-30
-1.0
Typ. Max. Units

Conditions

V
V GS = 0V, ID = -250A
-0.019 V/C Reference to 25C, D
I = -1mA
0.015 0.020
VGS = -10V, ID = -8.0A
0.026 0.035
VGS = -4.5V, ID = -5.0A

V
VDS = VGS, ID = -250A
11
S
VDS = -15V, ID = -8.0A
-10
VDS = -24V, VGS = 0V
A
-10
VDS = -15V, VGS = 0V, TJ = 70C
-100
VGS = -20V
nA
100
VGS = 20V
40
60
ID = -4.6A
7.1
nC VDS = -15V
8.0
VGS = -10V
16
24
VDD = -15V, VGS = -10V
76 110
ID = -1.0A
ns
130 200
RG = 6.0
90 140
R D = 15
2320
VGS = 0V
390
pF
VDS = -15V
270
= 1.0kHz
Source-Drain Ratings and Characteristics

IS
ISM
VSD
trr
Qrr
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
Min. Typ. Max. Units
-2.5
A
-50
34
33
-1.2
51
50
V
ns
nC
Conditions
MOSFET symbol
showing the
G
integral reverse
p-n junction diode.
TJ = 25C, SI = -2.5A, VGS = 0V
TJ = 25C, FI = -2.5A
di/dt = -100A/s
Notes:
Repetitive rating; pulse width limited by
Surface mounted on FR-4 board, t 5sec.
max. junction temperature.
Pulse width 300s; duty cycle 2%.
--26--
TDA7496L
2W+2W AMPLIFIER WITH DC VOLUME CONTROL

2W+2W OUTPUT POWER
RL = 8 @THD = 10% VCC = 14V
ST-BY AND MUTE FUNCTIONS
LOW TURN-ON TURN-OFF POP NOISE
LINEAR VOLUME CONTROL DC COUPLED
WITH POWER OP. AMP.
NO BOUCHEROT CELL
NO ST-BY RC INPUT NETWORK
SINGLE SUPPLY RANGING UP TO 15V
SHORT CIRCUIT PROTECTION
THERMAL OVERLOAD PROTECTION
INTERNALLY FIXED GAIN
SOFT CLIPPING
VARIABLE OUTPUT AFTER VOLUME CONTROL CIRCUIT
POWERDIP (14+3+3) PACKAGE
Powerdip (14+3+3)
ORDERING NUMBER: TDA7496L
14+3+3 package, specially designed for high

quality sound, TV and Monitor applications.
Features of the TDA7496L include linear volume
control, Stand-by and mute functions.
DESCRIPTION
The TDA7496L is a stereo 2W+2W class AB
power amplifier assembled in the @ Powerdip
BLOCK DIAGRAM
VAROUT_R
GND
1,2,3,13,
18,19,20
470nF
15,16
VOLUME
INR
VS
30K
1000F
14
OUTR
OP AMP
S1 ST-BY
11
+5V
STBY
MUTE/STBY
PROTECTIONS
VOLUME
470nF
12
MUTE
17
+
30K
OUTL
1000F
OP AMP
SVR
10
470F
6
VOLUME
5
VAROUT_L
+5V
D97AU596A
100nF
+5V
1F
S2 MUTE
INL
10K
60K
S_GND
300K
--27--
ABSOLUTE MAXIMUM RATINGS

Symbol
Parameter
Value
DC Supply Voltage
VS
8
6
0 to 70
Vpp
W
C
-40 to 150
Maximum Input Voltage

Total Power Dissipation (Tcase = 60C)
Ambient Operating Temperature
VIN
Ptot
Tamb
Tstg, Tj
Storage and Junction Temperature

Volume CTRL DC voltage
V6
PIN CONNECTION
Unit
26
Rth with "on board" Square Heatsink vs. copper area.

Rthj-a
(C/W)
GND
20
GND
GND
19
GND
GND
18
GND
INL
17
OUTL
VAROUT_L
16
VS
VOLUME
15
VS
VAROUT_R
14
OUTR
N.C.
13
GND
INR
12
MUTE
SVR
10
11
STBY
D97AU675
COPPER AREA 35
THICKNESS
60
PC BOARD
50
40
D97AU597A
30
0
12
Area(cm2)
THERMAL DATA
Symbol
Rth j-pins
Rth j-amb (*)
Value
Unit
Thermal Resistance Junction-pins
Parameter
max.
15
C/W
Thermal Resistance Junction-ambient
max.
50
C/W
(*) Mounted on PCB with no heatsink
ELECTRICAL CHARACTERISTICS (Refer to the test circuit VS = 14V; RL = 8, Rg = 50, Tamb = 25C).
Symbol
VS
Iq
DCVOS
VO
PO
THD
Ipeak
Vin
GV
GvLine
AMin VOL
BW
Parameter
Supply Voltage Range
Total Quiescent Current
Output DC Offset Referred to
SVR Potenial
Quiescent Output Voltage
Output Power
Total Harmonic Distortion
Output Peak Current
Input Signal
Closed Loop Gain
Monitor Out Gain
Attenuation at Minimum Volume
Test Condition
Min.
10
25
200
No Input Signal
THD = 10%; RL = 8;
1
THD = 1%; RL = 8;
1
GV = 30dB; PO = 1W; f = 1KHz;
(internally limited)
Vol Ctrl > 4.5V
Vol Ctrl > 4.5V; Zload > 30K
Vol Ctrl < 0.5V
Typ.
.6
7
2
.3
0.7
0.9
28.5
-1.5
80
30
0
0.4
0.6
--28--
Max.
18
50
2.8
31.5
1.5
Unit
V
mA
mV
V
W
W
%
A
Vrms
dB
dB
dB
MHz
ELECTRICAL CHARACTERISTICS (continued)

Symbol
eN
SR
Ri
RVar Out
Rload Var Out
SVR
TM
Ts
Parameter
Total Output Noise
Test Condition
f = 20Hz to 22KHz
Play, max volume
f = 20Hz to 22KHz
Play, max attenuation
f = 20Hz to 22KHz
Mute
Slew Rate
Input Resistance
Variable Output Resistance
Variable Output Load
Supply Voltage Rejection
Min.
5
22.5
f = 1kHz; max volume

CSVR = 470F; VRIP = 1Vrms
f = 1kHz; max attenuation
CSVR = 470F; VRIP =1Vrms
Typ.
500
Max.
800
Unit
V
100
250
60
150
100
2
35
39
V/s
K
K
dB
55
65
dB
150
160
C
C
Thermal Muting
Thermal Shut-down
8
30
30
MUTE STAND-BY & INPUT SELECTION FUNCTIONS

VST ON
VST OFF
VM ON
VM OFF
IqST-BY
AMUTE
IstbyBIAS
ImuteBIAS
Stand-by ON Threshold
Stand-by OFF Threshold
Mute ON Threshold
Mute OFF Threshold
Quiescent Current @ Stand-by
Mute Attenuation
Stand-by bias current
Mute bias current
3.5
1.5
3.5
50
Stand by on VST-BY = 5V
VMUTE = 5V
Play or Mute
Mute
Play
-20
0.6
65
80
-5
1
0.2
1.5
1
5
2
V
V
V
V
mA
dB
A
A
A
A
A
APPLICATION SUGGESTIONS
The recommended values of the external components are those shown on the application circuit of figure 1A. Different values can be used, the following table can help the designer.
R1
SUGGESTION
VALUE
300K
R2
P1
10K
50K
C1
1000F
C2
C3
C4
C5
470nF
470nF
470F
100nF
C6
1000F
C7
C8
1F
1000F
C9
100nF
COMPONENT
PURPOSE
Volume control
circuit
Mute time constant
Volume control
circuit
Supply voltage
bypass
Input DC decoupling
Input DC decoupling
Ripple rejection
Volume control time
costant
Output DC
decoupling
Mute time costant
Output DC
decoupling
Supply voltage
bypass
LARGER THAN
SUGGESTION
Larger volume regulation
time
Larger mute on/off time
SMALLER THAN
SUGGESTION
Smaller volume regulation
time
Smaller mute on/off time
Danger of oscillation
Lower low frequency cutoff
Better SVR
Larger volume regulation
time
Higher low frequency cutoff

Worse SVR
Smaller volume regulation
time
Larger mute on/off time

Smaller mute on/off time

--29--
Danger of oscillation
BLOCK DIAGRAM
MODEL NAME : L70S
D
14.318Mhz
Analog
RGB
Scaler
DUAL LVDS
(MST 9111)
17"
LCD
PANEL
POWER &
INVERTER
Micro
Controller
24Mhz
B
WT61P4
AUDIO(TDA7496L)
SPEAKER
Title
Image Quest Co., Ltd.

BLOCK DIAGRAM
L70S
<Title>
Size
A
Date:
5
Document Number
<Doc>
Monday, March 17, 2003

2
Rev
Sheet
of

!
"

!
"

#

$

$

$$
!"

$

'$ &
!( !

$

$$
"

%

%'
%! !%

%

%'
%! !%

%

%'
%! !%

%

%'$
" !%

%

%'$
" !%

%

%'$
" !%

%

%'$
" !%

%

%'$
" !%

$$
%' '$

$$
% $

&

&

)
$%

!% $% '$

)
$%

!% $% '$

!
"

!
"
$$
%!& !'

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!' ("

!
"

!
"

!
"

!
"

!' ("

!
"

!
"

!
"

!' ("

!' ("

!' ("

!
"

!
"

!' ("

! ' * ("

!
"

! ' * ("

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

!
"

! ' * ("

!
"

!
"

!
"

! ' * ("

!
"

!
"

!
"

!
"

!
"

!
"

!
"

$

!$
"

' '$
! !

!'% !%

' '$
!

'
!$ !+

"

$$
!

'
!+!&

' '$
% %'

'&)
!+ !%

'&)
!%

%
$ %

! !!,
!( !

" -'$
! +

$$
%! & )

$$
!% & !!,

& !$
& ' %

!'$ -" & & !!,

!
&'$ - .

!
&'$ - .

!
&'$ - .

!
&'$ - .

!
&'$ - +

!
&'$ - .

!
&'$ - .

!$%

'$
! $

!!
!

'$ &

'$ &

'$ !!
!

"'
! '/++0

! '
+ +

! '
++

'$
!/%0

'$
!/%0

!$% $
!/%0

!$%
!/%0

!$% &!
!/%0

$
!

$ !/%(0

! /%(0

!!
! ') !'

!$% !! ! /%(0

!$% &! !!

!/%0

+ '$

$&
! /,0

% $!

%
$%

%
$% &

&
/!0 (

$ &

!'$
!

!'$ &
!

&&
!

%
%
!"

&+ $
)$

&$% !)
!

%
$ & (

%
$

& &
!( ')/ +0(!'

! , &'$ !'

% $ ')/ +0

!% &(% !!,

!( !

&%&
! $ .

& !$
%' '$ &

!' !'

'$! '% 1 ! ' $

&&
&
&(% /%'0

&
' & 1 $ !( ' (!'

&
&
)$ /#0

&
% !!
! ') !'
' !

/ 0 +

&
' !!

! ') !'

&
'$ !!
!

'$ !!(
! +

%
" &

& '$/0(
!

& '$/0(
!

& '$/0(
!

! "
&'$/-0 . !

5
VCC12V
VCC5V
VCPU
C2
100uF/16V
C1
100uF/16V
DIP_2.0P1
12V
1
5V
2
3
GND
4
5
On/Inverter
6
Adj/Backlite
7
CON1
Board In Type
L1
0V : MAX BRIGHTNESS
5V : MIN BRIGHTNESS
onBACKLITE
AdjBACKLITE
to
Inverter/power
C5
C3
C4
0.1uF
open
open
GND
R4
1K
VCC5V
onPANEL
ACTIVE LOW
GND
GND
VLCD
U2
1
2
3
4
C13
C14
C15
open
open
1uF/1608
S
S
S
G
D
D
D
D
8
7
6
5
C11
22uF/16V
SI4435 SO8
GND
C12
0.1uF/1608
GND
GND
VCC2.5VD
VCC5V
U1
RC1117S2.5T
C7
C8
22uF/16V
0.1uF/1608
VIN
VOUT
GND
1
GND
C9
C10
0.1uF/1608
22uF/16V
GND
GND
GND
GND
VCC3.3VD
VCC3.3V_AV
U3
RC1117S3.3T
3
VIN
VOUT
VCC3.3V_PL
2
VCC3.3VD_PL
C17
22uF/16V
GND
C18
0.1uF/1608
1
GND
GND
GND
Image quest Co., Ltd.
Title
L70S
Size
Date:
Document Number
Rev
DC-DC
Tuesday, April 22, 2003
Sheet
of
D
CN1
1
6
2
7
3
8
4
9
5
10
R13
2
0
D1
D2
KDS226
R17
75
KDS226
C25
open
KDS226
DSUB-15
C20
0.1uF/1608
C21
0.1uF/1608
C22
0.1uF/1608
C23
open
R19
100
C24
0.1uF/1608
R22
C28
0.1uF/1608
C29
0.1uF/1608
100
R21
75
D3
15
14
13
R8
100
R11
100
R14
R10
12
R7
11
R18
75
C27
open
C26
open
RIN0
GIN0
BIN0
SOG0
GNDR0
0
R23
100
VCPU
0
R9
0
R12
0
R15
0
R16
0
R20
GNDG0
0
R25
R24
GNDB0
100
ISP_DAT
ISP_CLK
HSI
R26 20
VSI R28
D9
1N4148
R5
0
R30
47K
R31
47K
VCC
5V
D5
D6
6.2V
6.2V
D4
6.2V
C30
5P
R35
open
C31
220P
R27
R29
100
R34
100
HSYNC0
VSYNC0
ST_DET0
R36
4.7K
C16
0.1uF/1608
U8
8
7
6
5
R1
100
R2
100
VCC
VCLK
SCL
SDA
NC
NC
NC
GND
1
2
3
4
24LC21
D8
6.2V
D7
Option
6.2V

Title
L70S
A
Size
Document Number
Rev
VGA_INPUT
Date:
Sheet
of
3.3V_DVI
3.3V_PL
RIN0
RIN0M
GIN0
GIN0M
SOGIN0
BIN0
BIN0M
HSYNC0
VSYNC0
DDC1_CLK
DDC1_DAT
16
124
8
14
D
3.3VD
2.5VD
VDDC
VDDC
VDDC
VDDC
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD_DVI
AVDD_DVI
33
32
30
29
31
28
27
126
127
118
117
AVDD_PLL
AVDD_PLL
RIN0
RIN0M
GIN0
GIN0M
SOGIN0
BIN0
BIN0M
HSYNC0
VSYNC0
LVA1P
LVA1M
LVA2P
LVA2M
3.3V_AV
0.1uF/1608
0.1uF/1608
0.1uF/1608
0.1uF/1608
R86
390 1
R37
open
AdjBACKLITE
C45
C46
C47
HFS
HCLK
HDATA
HWRESET
INT
EEPROM_CLK
EEPROM_DAT
3
4
6
7
9
10
12
13
15
C55
22pF
C48
37
36
38
39
40
42
41
121
43
119
120
44
45
122
LVACKP
LVACKM
RIN1
RIN1M
GIN1
GIN1M
SOGIN1
BIN1
BIN1M
HSYNC1
VSYNC1
DDC2_CLK
DDC2_DAT
3.3VD
L3
0
C32
LVA0P
LVA0M
LVA3P
LVA3M
25
26
23
24
22
20
21
128
1
116
115
LVB0P
LVB0M
LVB1P
LVB1M
MST9111
LVB2P
LVB2M
LVB3P
LVB3M
R+
RG+
GB+
BCK+
CKREXT
LVBCKP
LVBCKM
REFP
RMID
REFM
REF_GND
VCLK
VD0
VD1
VD2
VD3
VD4
VD5
VD6
VD7
HFS
HCLK
HDATA
HWRESETZ
INT
DDCROM_CLK
DDCROM_DAT
VPLL
GPLL
TESTPIN
PWM0
PWM1
80
81
LVA0
LVA1
78
79
LVA2
LVA3
76
77
LVA4
LVA5
70
71
LVA6
LVA7
74
75
LVA8
LVA9
96
97
LVB0
LVB1
92
93
LVB2
LVB3
90
91
LVB4
LVB5
86
87
LVB6
LVB7
88
89
LVB8
LVB9
0.1uF/1608
0.1uF/1608
VCC2.5VD
2.5VD
C40
C41 C42 C43 C44 0.1uF/1608

0.1uF/1608
0.1uF/1608
0.1uF/1608
10uF/16V
VCC3.3V_AV
3.3V_AV
L5
0
C49
C50 C51
10uF/16V
0.1uF/1608
0.1uF/1608
VCC3.3V_PL
L6
46
47
48
49
50
51
52
53
54
3.3V_PL
0
C52
10uF/16V
C54
0.1uF/1608
103
102
2
VCC3.3VD_PL
C53
0.1uF/1608
3.3VD_PL
L7
R38
open
2.5VD
0
C56
C57
0.1uF/1608
57
GNDC
63
GNDC
84
GNDC
112
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
R39
56
62
73
83
95
106
113
AVSS_DVI
AVSS_DVI
5
11
17
AVSS_PLL
125
AVSS_PLL
AVSS
AVSS
19
34
C58
22pF
XOUT
0.1uF/1608 0.1uF/1608
0.1uF/1608 0.1uF/1608
0.1uF/1608
L4
0
10uF/16V
123
C33 C34 C35 C36 C37 C38 C39
10uF/16V
XIN
Y1
14.318MHZ
3.3VD_PL
VCC3.3VD
AVDD
AVDD
AVDD
AVDD
U4
8
14
18
35
3.3V_AV
58
64
85
111
55
61
72
82
94
107
114

Title
L70S
A
Size
Document Number
Rev
MST9111
Date:
Sheet
of
VCPU
VCPU
open R41
R40 open
VCPU
R42
10K
C59
0.1uF/1608
VCPU
C63
22PF/1608
C61
47uF/16V
C64
47uF/16V
5
1
2
3
4
16
INT
R54
R56
VCPU
C
R62
open
R57
R59
R60
R64
R65
R63
open
R66
R67
470
470
470
470
470
200
200
26
27
28
29
30
31
32
33
41
42
VCPU
PB.6/SDA2
PB.5/SCL2
PB.4
PB.3
PB.2
PB.0
PC.7
PC.6
PC.5
PC.4
PC.3
PC.2
PC.1
PC.0
INT0/PB.1
PA0/SDA1
PA1/SCL1
PA.2
PA.3
PA.4
PA.5
PA.6
PA.7
HIN
VIN
AdjBACKLITE
R46
100
VCPU
C66
0.1uF/1608
R48
4.7K
R50
4.7K
R51
R52
100
100
R55
100
HFS
HCLK
HDATA
DPMS
onPANEL
R53
4.7k
HWRESET
R61
10K
R58
22K
onBACKLITE
Q2
1
C68
0.1uF/1608
C67
0.1uF/1608
TT2N3904D
VCPU
44
R68
330
R69
330
WT61P4 PLCC
C70
470pF/1608
RN2
open
R49
4.7K
VCPU
11
12
13
14
15
17
18
19
20
21
22
23
24
25
C72
open
C71
open
VCPU
R70
470
1
2
3
4
RN1
4.7K
1
2
3
4
NC
34
35
36
37
38
39
40
43
8
7
6
5
8
7
6
5
C69
open
PD.0
PD.1
PD.2
PD.3
PD.4
PD.5
PD.6
PD.7
RESET
PE.3
PE.2
PE.1
PE.0
HSYNC0
VSYNC0
150
150
XTAL2
C65
22PF/1608
R47
10K
XTAL1
VSS
U5
10
VCPU
R44
4.7K
7
R45
1M
Y2
24MHZ
VDD5
MUTE
ST-DET1
C62
0.1uF/1608
R43
8.2K
C60
1uF
VDD3
VOLUME
C73
0.1uF/1608
ISP_DAT
ISP_CLK
U6
1
2
3
4
A0
A1
A2
GND
VCC
WP
SCL
SDA
8
7
6
5
R72
R73
R71
470
100
100
24C08
EEPROM_CLK
DIP_2.0P
MENU
SELECT
DOWN
UP
GND
LED-G
LED-O
PWR-SW
AUDIO/GL
AUDIO/L
AUDIO/RG
AUDIO/R
EEPROM_DAT
1
2
3
4
5
6
7
8
9
10
11
12
LED_G
LED_O
L/GND
AUDIO/L
R/GND
AUDIO/R
CN2
to KEY PAD

Title
Size
L70S
Document Number
Rev
MPU
Date:
Sheet
of
LVA[0..9]
LVA[0..9]
VLCD
CON4
LVA6
LVA7
LVA8
LVA9
LVA4
LVA5
R90
R91
R92
R93
R94
R95
LVA2
LVA3
R96
R97
0
0
0
0
0
0
RXE3+
RXE3RXEC+
RXECRXE2+
RXE2-
0
0
RXE1+
RXE1-
LVA0
LVA1
LVB6
LVB7
LVB8
LVB9
R98
R99
R100
R101
R102
R103
0
0
0
0
0
0
RXE0+
RXE0RXO3+
RXO3RXOC+
RXOC-
LVB4
LVB5
LVB2
LVB3
LVB0
LVB1
R104
R105
R106
R107
R108
R109
0
0
0
0
0
0
RXO2+
RXO2RXO1+
RXO1RXO0+
RXO0-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
DUAL LVDS
CON30
LVB[0..9]
LVB[0..9]

Title
L70S
Size
Document Number
Rev
PANEL
Date: Tuesday, April 22, 2003
Sheet
of
VCC12V
VCC5V
L8
C75
C74
C76
C77
0.47UF
VOLUME
AUDIOJACK
GND
0.47UF
4
R89
1K
6
R79
1K
C79
10uF/16V
7
C82
0
C81
0
5
R85
270
R84
270
INR
VOLUME
Vs
Vs
OUTR
STBY
MUTE
OUTL
VAROUT_R
VAROUT_L
GND
10
TDA7496L
INL
SVR
GND
GND
GND
GND
GND
GND
GND
15
16
14
GND
C78
MUTE
10K
R80
R/GND
AUDIO/R
AUDIO/L
L/GND
1K
12
17
C80
J2
L10
L11
1608/HB60
3
2
1608/HB60
330uF/16V
1
2
3
13
18
19
20
R78
150
330uF/16V
11
1
5
R81
150
R83 OPEN
2
1
U7
R88
1K
47uF/16V
0.1uF
J1
R77
Q5
TT2N3904D
C83
1uF
EARPHONE JACK
R82
10K
GND
GND
GND
GND
C84
220/10V
GND
B
GND
Title
Size
B
Date:
5

L70S
Document Number
Rev
AUDIO
Sheet
1
of

!"
#

$
%

" &'
()
*+

'!,+
$
,-
# ,
% ,!-
,!
( ,-
* ,
$
!,'
"
.%&'/
$
14
15
24
25
13
16
17
12
11
10
18
19
9
22
8
20
21
7
6
25
5004000194
SCREW
SCR-TT,MC4X10
24
5004000208
SCREW
SCR-TT,MC4X12
ABS 94 HB
23
62013190
STAND BASE
22
3010700826
OSD PCB ASSY
21
3610200118
PWR-INV. PCB ASSY
20
E42086XXXX
MAIN PCB ASSY
19
5001000666
SCREW
SCR-MC,BIN+MC3X5
18
5004000197
SCREW
SCR-TT,MC3X10
17
5004000190
SCREW
SCR-TT,MC3X8
16
5004000192
SCREW
SCR-TT,MC3X6
15
5004000190
SCREW
SCR-TT,MC3X8
14
62013186
HINGE CAP L
ABS 94 HB
13
62013187
HINGE CAP R
ABS 94 HB
12
62013188
STAND FRONT
ABS 94 HB
11
61150252
HINGE ASSY
10
62013189
STAND REAR
ABS 94 HB
62013215
COVER REAR
ABS 94 HB
3550100115
SPEAKER L/R
61012211
MAIN FRAME
EGI T=0.8
5001000666
SCREW
SCR-MC,BIN+MC3X5
3330XXXXXX
17" LCD
62200857
LENS LED
PMMA
1
1
1
5
23
2
1
62152407
KNOB TACT
ABS 94 HB
62013213
COVER FRONT
ABS 94 HB
62013214
COVER PANEL
ABS 94 HB
NO
PART NO
PART NAME
DESCRIPTION
AUO/SEC/HYDIS
DRAWN
BY
PLANNED
BY
CHECKED
BY
APPROVED
BY
ANGLE
3rd
J.S.WOO
J.J.LEE
J.S.KIM
'03.05.09
'03.05.09
'03.05.09
L70S BRAND
REF
NO.
A
REMARK
REV
SCALE
MDL
TAMP 031-2
QT'Y
TITLE
SIZE
EXPLODED VIEW
DWG NO.
A2
00
SHEET
1
1
FILE NAME : EXPLODED VIEW

Hyundai l70s

Uploaded by

Copyright:

Available Formats

Hyundai l70s

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hyundai l70s

Uploaded by

Copyright:

Available Formats

L70S

TFT LCD Color Monitor

TECHNICAL SERVICE MANUAL

L70S Technical Service Manual

Power Switch / LED Indecator

L70S Technical Service Manual

Video Input Signal

Signal: 256 level gray

Video Input Terminal

D-Sub miniature connector

L70S Technical Service Manual

Connecting with External Equipment

L70S Technical Service Manual

On Screen Controls & LED Indicator

he OSD adjustments available to you are listed below.

L70S Technical Service Manual

Getting Fine Picture

15 pin D-SUB Connector

Contrast,Brightness, Position, Auto Color,

Clock Phase, Color Control, Language,

VESA DPMS Standard

FCC CLASS B , CE , VCCI

cULus, CE, TUV-GS, SEMKO

372.5 X 398 X 185 mm

* Specification is subject to change without notice for performance improvement.

L70S Technical Service Manual

Critical Parts Specification

Interface Connector / Interface card

Type Parts Number

Mating Housing Part Number

Connector Name / Designation

Lamp Connector / Backlight lamp

Type Parts Number

Mating Type Part Number

L70S Technical Service Manual

Negative LVDS differential data input (odd data)

Positive LVDS differential data input (odd data)

Negative LVDS differential data input (odd data)

Positive LVDS differential data input (odd data)

Negative LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)

Positive LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)

Negative LVDS differential clock input (odd clock)

Positive LVDS differential clock input (odd clock)

Negative LVDS differential data input (odd data)

Positive LVDS differential data input (odd data)

Negative LVDS differential data input (Even clock)

Positive LVDS differential data input (Even data)

Positive LVDS differential data input (Even data)

Negative LVDS differential data input (Even data)

Negative LVDS differential data input (Even data)

Positive LVDS differential data input (Even data)

Negative LVDS differential clock input (Even clock)

Positive LVDS differential clock input (Even clock)

Negative LVDS differential data input (Even data)

Positive LVDS differential data input (Even data)

Vertical Sync : Both Positive and Negative polarity are acceptable

Horizontal Sync : Both Positive and Negative polarity are acceptable

GENERAL DESCRI PTION

High-quality zoom and shrink scaling engine