Sika Injection-215 RF 2014-02-1

Product Data Sheet
Edition 2014-02_1
Sika Injection-215 RF
Construction
Single component, solvent-free, low viscosity hydrophobic

polyurethane grout
Product
Description
Sika Injection-215 RF is a single component hydrophobic hydroactive injection
grout based MDI (methylene-diphenyl isocyanate) polyurethane. Sika Injection

215 RF has very fast reaction time. When Sika Injection-215 RF reacts with
water, it starts to foam and expand very quickly. As the grout reacts, it expands
and stops the water leak within a very short period of time. Expansion ratio is
dependent on the amount of water added to the resin mixture and the moisture
level in the environment. It reacts to form a very dense and flexible material or to
a flexible foam.
Uses
To seal leaking live crack movement joints, pipe intrusions, etc. suffering from
infiltration in:
- Basements
- Concrete below water table
To seal and fill defective concrete (honeycombs, voids, etc.)
Characteristics /
Advantages
Totally water resistant

Solvent free
Non-flammable
No shrinkage
Non-toxic in cured form
Reacts rapidly
Resistant to biological attack and to mild acids, alkalis, etc.
Product Data
Form
Appearance / Colour
Dark Brown
Packaging
20 kg pails
Storage
Storage Conditions /
Shelf Life
12 months from date of production if stored properly in undamaged unopened,

original sealed packaging, in dry conditions at temperatures between +5C and
+30C. Protect from direct sunlight and frost.
Opened pails must be resealed immediately after use.
Material exposed to atmospheric moisture will cure within 7 10 days.
Shake the pails before use and once opened should be used as soon as possible.
1/3
Technical Data
Viscosity (+25C)
400 600 cps
(ASTM D1638-74)
Solid
100 %
(ASTM D1010)
Flash Point, C
178
(ASTM D1010)
Density
1.13 g/ml
Corrosiveness
Non-corrosive
Cured Product
Elongation
(ASTM D3800-79)
10%
Tensile Strength
85 psi
Unconfined Compressive Strength (sand filled)
1600 psi
Corrosiveness
Non-corrosive
Induction Time
120 seconds
Toxicity (Drinking water)
Cured material is essentially non-toxic
Max Expansion
3000%
System Information
Application Details
Application
Instructions
Application Method /
Tools
By single action piston pump operating at high pressure

By twin piston pump when mixed with water (1:1) to produce foams of different
densities
Sika Injection-215 RF is for injection directly in water bearing cracks and joints.
On contact with water, it forms and expands to fill voids and prevent infiltration.
Cures to form a flexible seal.
Sealing Cracks (minimum crack width is 0.2 mm)
Drill 15 22 mm holes along the side of the crack at a 45 angle. Drill the holes to
intersect the crack midway. Install injection packers in the holes and tighten. If the
crack to be injected is 10 mm wide or more at the surface, pack an open cell
polyurethane foam saturated with Sika Injection-215 RF into the crack. Spray the
saturated foam with a small amount of water to activate the grout and create a
surface seal.
Pump Sika Injection-215 RF at >20 bar into or behind fissures or into voids which
are allowing water to infiltrate into unwanted areas. If voids in concrete being
injected contain insufficient moisture to activate the grout, inject a small amount of
water prior to injecting the grout. Pump Sika Injection-215 RF for approximately
45 seconds and then pause to allow the material to flow into all the cracks and
crevices. Keep pumping, watch for material flow and water to appear at the
surface of the next packer. When movement stops or Sika Injection-215 RF

appears at the next packer move to the next packer and inject. When sealing
vertical cracks start at the bottom and work upwards.
Refer to our Technical Service Department for advice on smaller cracks.
Final Cure
24 hours
Cleaning of Tools
Completely flush the pump and hose with Sika Colma-Cleaner or Thinner C. Use
putty knife or trowel to remove excess material from walls, floors, etc. Wait for the
material to cure before removing. May be sanded off.
Notes on Application /
Limitations
Expanding Sika Injection-215 RF exerts a pressure of up to 3 bar. Consideration

should be given to the effect of this on the structure.
Use caution when cleaning the equipment with flammable agents.
2/3
Construction
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Health and Safety

Information
For information and advice on the safe handling, storage and disposal of chemical
products, users should refer to the most recent Material Safety Data Sheet
containing physical, ecological, toxicological and other safety-related data.
Legal Notes
The information, and, in particular, the recommendations relating to the

application and end-use of Sika products, are given in good faith based on Sika's
current knowledge and experience of the products when properly stored, handled
and applied under normal conditions in accordance with Sikas recommendations.
In practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular
purpose, nor any liability arising out of any legal relationship whatsoever, can be
inferred either from this information, or from any written recommendations, or from
any other advice offered. The user of the product must test the products
suitability for the intended application and purpose. Sika reserves the right to
change the properties of its products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be supplied on
request.
Sika Kimia Sdn Bhd

Lot 689 Nilai Industrial Estate
71800 Nilai, Negeri Sembilan DK
MALAYSIA
Phone: +6 06 799 1762

Fax:
+6 06 799 1980
e-mail:info@my.sika.com
www.sika.com.my
3/3

Sika Injection-215 RF 2014-02-1

Uploaded by

Copyright:

Available Formats

Sika Injection-215 RF 2014-02-1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sika Injection-215 RF 2014-02-1

Uploaded by

Copyright:

Available Formats

Product Data Sheet

Single component, solvent-free, low viscosity hydrophobic

Sika Injection-215 RF is a single component hydrophobic hydroactive injection

grout based MDI (methylene-diphenyl isocyanate) polyurethane. Sika Injection

Totally water resistant

12 months from date of production if stored properly in undamaged unopened,

400 600 cps

Unconfined Compressive Strength (sand filled)

Toxicity (Drinking water)

Cured material is essentially non-toxic

By single action piston pump operating at high pressure

surface of the next packer. When movement stops or Sika Injection-215 RF

Expanding Sika Injection-215 RF exerts a pressure of up to 3 bar. Consideration

Health and Safety

The information, and, in particular, the recommendations relating to the

Sika Kimia Sdn Bhd

Phone: +6 06 799 1762

You might also like