Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
48 views

Pole Frame Construction - Suggested Details: City of Novi

This document provides suggested details for pole frame construction, including: - Poles are placed in the ground around the building perimeter to provide structural support, replacing concrete foundations. - Pole size depends on eave height, building width, and pole spacing based on tables provided. Poles must be properly treated and embedded in concrete pads. - Rafter plates connect the roof load to the poles based on size tables. Trusses spaced 4 feet apart support the roof load. - Bracing is required for the roof and walls to provide lateral support against wind and other loads.

Uploaded by

ruwanpura
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
48 views

Pole Frame Construction - Suggested Details: City of Novi

This document provides suggested details for pole frame construction, including: - Poles are placed in the ground around the building perimeter to provide structural support, replacing concrete foundations. - Pole size depends on eave height, building width, and pole spacing based on tables provided. Poles must be properly treated and embedded in concrete pads. - Rafter plates connect the roof load to the poles based on size tables. Trusses spaced 4 feet apart support the roof load. - Bracing is required for the roof and walls to provide lateral support against wind and other loads.

Uploaded by

ruwanpura
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

POLE FRAME CONSTRUCTION - SUGGESTED DETAILS

CITY OF NOVI
Community Development Department
(248) 347-0415
The following information was prepared by James S. Boyd, Agricultural Engineer, Michigan State University
in December 1997. Information was verified in February 2005 for accuracy.
In pole frame construction, poles are placed four feet in the ground around the perimeter of the building.
Concrete pads are poured into the holes before the poles are set. These poles and pads replace concrete
block or concrete foundations.
The poles anchor the structure to the ground, and the side walls and roof framing are nailed solidly to the
poles. This type of construction provides flexibility in the use of the building and can be used with many
attractive exterior treatments.
Poles
Size:

Poles provide the structural support for this type of construction. The size of the poles should
conform to Table I depending on the eave height, width of building, and the spacing of the poles.

Treatment:

All poles used as main support poles should conform to the latest edition of the American
Wood Preservers Association Standards. Poles should be grade stamped to show both the
type of preservative and minimum retention as shown in the following table:

Preservative

Minimum Retention

Creosote AWPS Pl
Pentachlorophenol AWPA P8
Cooper Chrome Arsenate AWPA LP22

10.0 lb per cubic foot


0.5 lb per cubic foot
0.42 lb per cubic foot

Depth of Embedment: All poles should be set in the ground a minimum of one-fourth (1/4) its length, but at
least a minimum of four (4) feet.
Pads: A concrete pad should be placed below the depth of embedment of the pole. Only properly
proportioned and mixed concrete with a test strength of 3000 psi must be used. It should be placed
in the bottom of the hole and obtain its initial set before the pole is set.
Size:

The size of the pad should conform to Table II. The depth of the pad should be one-half (1/2) the
diameter of the pad. All holes should be dug deep enough to provide for depth of embedment plus
the depth of the pad.

Table I
Pole Selection
Eave Height

8 feet

8' Pole Spacing

12' Pole Spacing

16' Pole Spacing

4" or 4x4 thru 40' span

4" or 4x6 thru 40' span

4" or 4x6R thru 30' span

4" or 4x6 thru 60' span

4" or 4x6R thru 60' span

5" or 4x6R thru 50' span


5" or 6x6 thru 60' span

10 feet

4" or 4x6 thru 40' span

5" or 6x6 thru 50' span

5" or 6x6R thru 40' span

4" or 4x6R thru 50' span

5" or 6x6R thru 60' span

6" thru 60' span

50" thru 60' span

6" thru 60' span

5" thru 50' span

6" thru 50' span

5" or 4x6R thru 60' span


4" or 6x6 thru 40' span
12 feet

5" or 6x6 thru 50' span


5" or 6x6R thru 60' span
5" thru 60' span

14 feet
6" thru 60' span
6-1/2" thru 60' span
"R" after a pole size refers to a rough cut pole with full dimension. Size for round poles is top diameter.

Table II
Concrete pad recommendations for various building widths and pole spacings
Building Width (feet)

Pole Spacing (feet)

Pad Diameter (inches)

24 feet

8 feet
12
16

12 inches
14
16

30 feet

8 feet
12
16

14 inches
16
18

36 feet

8 feet
12
16

14 inches
18
18

40 feet

8 feet
12
16

16 inches
20
22

50 feet

8 feet
12

18 inches
20

60 feet

8 feet
12

18 inches
22

Roof Support:
Design Load: Pole framing is designed for single story construction. Framing should be designed for a
minimum total load of 30 pounds per square foot.
Rafter Supports:

The roof load must be transferred to the poles by rafter plates attached to the poles.
The size of these rafter plates should conform to Table III. Rafter supports should be
of construction grade Douglas Fir or No. 2 kiln dried Southern Pine or equivalent.

Table III
Number and size of rafter plates required for clear span pole type buildings.
WIDTH OF BUILDING IN FEET
Pole
Spacing
8 feet

Truss
Spacing

30 feet
(number)

36 feet
(number)

40 feet
(number)

50 feet
(number)

60 feet
(number)

4' 0"

1 2x6
1 2x8

2 2x8

2 2x8

1 2 x 10

2 x 10

12 feet

4' 0"

2 2 x 10

1 2 x 12

1 2 x 12

3 2 x 12

3 2 x 12

16 feet

4' 0"

2 2 x 12

3 2 x 12

These dimensions are not recommended without an Engineer? s Seal.

Fasteners:

Roof supports are securely fastened to the poles with deformed shank nails or a combination
of deformed shank nails and bolts. The number of six (6) inch deformed shank nails per pole
are shown in Table IV.

Table IV
Number of six-inch ring or screw-shank nails required on each pole. **
WIDTH OF BUILDING IN FEET
Pole Spacing

30 feet

36 feet

40 feet

50 feet

60 feet

8 feet

26

31

35

43

51

12 feet

39

46

51

64

77

16 feet

52

62

**Pupe 5/8 inch bolt can be substituted for eight (8) nails in a joint.
When there is insufficient contact between the rafter plates and the pole to receive the required number of
nails and/or bolts, a scab can be fastened below the rafter plates to receive additional nails.

Trusses:

Roof trusses should be spaced four foot (4') on center and be capable of supporting the roof
load of 30 psf total. If greater spacings are used, the trusses must be designed to hold the
additional load.

Truss designs should be certified by a registered engineer.


The tops of poles on opposite sides of the building will be tied with a truss wherever possible and securely
fastened with six (6) inch deformed shank nails. Intermediate trusses will be securely fastened to the rafter
plates with 4" x 6" ties long enough to extend from the bottom of the rafter plate to the top surface of the
truss.
Roof Girts:

Roof girts should be 24 inches on center and laid flat across the trusses. At the connection
between the girt and each truss, provide two (2) four (4) inch deformed shank nails.

Bracing
Roof:

To provide for lateral support of the trusses, provide 2" x 4" braces the entire length of the building
on the bottom chord of the truss. For buildings up to 40 feet wide, use two (2) such braces and for
buildings over 40 feet, use three (3) braces. These braces should be located at the panel points on
the lower chord.

Wind: Wind pressure on the walls will cause the poles to bend at the ground line. A wind brace should be
provided at the eave for buildings with a side wall height of over ten (10) feet and for buildings 60
feet long and longer.
The brace should be a 2" x 6" at least 12 feet long, extending from the pole to the top chord of the
rafter, at an angle of 45? to the side wall. Securely nail the brace to the pole at the bottom and to the
top chord of the truss.
Horizontal side girts should b a maximum of two (2) feet O.C.

You might also like