CA 008006 en

Switches
Catalog Data
CA008006EN
Effective May 2015

Supersedes TD008005EN August 2014
COOPER POWER
SERIES
Disconnect and oil circuit recloser

bypass switches; regulator and current
transformer bypass switches
Contents
Description Page
D-73 Distribution-Class Disconnect Switch 2
M-72 Station-Class Disconnect Switch 4
H-72 Station-Class Disconnect Switch 6
D73RB 600A REA Approved Oil Circuit Recloser Bypass Switch 8
D73-3P Distribution-Class Oil Circuit Recloser Bypass Switch Switch10
M95-3P Station-Class Oil Circuit Recloser Bypass Switch12
Oil Circuit Recloser Station-Class Fused Bypass Combinations For Substation Mounting14
HB-65/HC-65 Station-Class Voltage Regulator Bypass Switch 16
M-72 Station-Class Bypass Switch18
H72-3P Station-Class Bypass Switch 20
HB-65 Current Transformer Bypass Switch 22
D73-LT Single Insulator Disconnect Switch (100 kV) 24
D73-LT Single Insulator Disconnect Switch (150 kV) 24
DLT Distribution-Class Inline Tension Disconnect Switch 25
D73-CD Distribution-Class Single Insulator Disconnect Switch 26
Catalog Data CA008006EN
Disconnect and oil circuit recloser bypass switches; regulator

and current transformer bypass switches
Effective May 2015
Introduction
Eaton's Cooper Power series Kearney disconnect and oil circuit
recloser bypass switches feature all copper bar current-carrying
parts, providing uniform strength and conductivity with no hidden
defects. Silver washers between the blade assembly and hinge act
as a bearing, ensuring easy blade opening, even after long exposure
to contaminated atmospheres. Eaton's Cooper Power series H-72
switch has silver inlays blazed to the hinge and jaw stationary
contacts. The truss-type blade assembly with wide hinge and formed
channel blades assures proper blade alignment during closing, even
with applied side forces. The positive blade latch prevents nuisance
openings and opening under fault conditions. The positive pryout
affords easy opening under icing conditions. Eaton's Cooper Power
series D-73, M-72 and H-72 switch models feature a 90 field
removable stop. The stop pin can be removed if 180 blade travel
is required. Tinned terminal pads accommodate either bronze or
aluminum terminals.
Eaton's Kearney regulator and current transformer bypass switches

feature sequenced, make before break operation in both 600 A and
1200 A ratings, minimizing the possibility of operator error. The
single-pull operation of the 600 A ratings both bypasses and
disconnects the regular or current transformer, or reconnects them
to the line. The two-pull operation of 1200 A ratings minimizes the
operating effort of these heavy-duty switches. An arcruptor or
snaphorn provided on regulator bypass switches interrupts the
regulator exciting current and prevents arcing and damage to the
switch contacts when disconnecting the regulator. Reverse loop
contacts on 600 A ratings increase contact pressure and minimize
the possibility of contact damage when subjected to high fault
current.
D-73 distribution-class disconnect switch

Eaton's D-73 distribution-class, single pole, single throw disconnect
switches provide a durable switch for line sectionalizing or isolating
equipment on distribution circuits. These switches are quality
constructed to ensure stable high current capability and full thermal
capacity under the required duties of todays load and short circuit
conditions.
Current Ratings: High current carrying capacity of 600 and 900 A
continuous and 40 kA momentary.
Blade Design: Truss-type construction of formed copper bars has
increased width at hinge for greater rigidity, thus minimizing side deflection and maintaining positive alignment when closing the switch.
Formed Steel Channel Base: Base and backstrap are rugged, hot
dipped galvanized steel and have a dead- ending hole at each end.
Minimum Current Interchanges: Uniform conductivity is assured
through utilization of hard drawn copper bar in forming one-piece
stationary contacts and terminal pads. Design reduces current
interchange points to a minimum.
Contacts: High pressure line type, both clip and hinge ends.
Contact Surfaces: 600 A ratings are silver to copper; 900 A are
silver to silver. Silver washers between blade and stationary hinge
act as a bearing to assure easy blade movement after long time
exposure to contaminated atmospheres.
Figure 1. D-73 single-pole disconnect switch.

Positive Blade Lock and Pryout: Blade latch prevents switch
opening under high momentary current. Easy opening is assured
through pryout assist.
Insulators: 2.25" B.C., characteristics available upon request.
Vertical or Underhung Mounting: Easily adaptable to single or
double crossarm construction.
90 Blade Stop: Stop can be field removed for 180 blade travel.
Special Applications: Variations to meet specific customer
requirements are available upon request.
Tin-Plated Terminal Pads: Accommodate terminals for either

aluminum or copper conductors.
Table 1. Terminal Assemblies
230026-S6 262013-S6

TWO-BOLT TINNED BRONZE

PARALLEL GROOVE CLAMP
Secured with two galvanized
steel bolts. Conductor range:
#6 Solid to 397.5 MCM ASCR,
500 MCM Copper or 556 MCM
Aluminum.
2
262224-1S6
TWO CAPTIVE STAINLESS

STEEL BOLTS
Factory installed, 1 3/4" long
bolts, accepts compression
terminals.
www.eaton.com/cooperpowerseries
COMPRESSION TERMINAL
Refer to Catalog 325-21
for complete information
relative to compression
fitting required.
BRIDGE TYPE TWO-BOLT

CLAMP
Accepts conductor sizes
ranging from #4 Solid to
500 MCM copper or aluminum.

Effective May 2015
Table 2. Dimensions and Ordering Information

Ratings
Catalog Number
Dimensions (inches),
Reference Only
kV Max.
Design
BIL
kV
Mom.
kA
600 A
900 A
Approx.Net Wt.
Ibs.
15.5
110
40
127700
127702CPS
11.88
15
25.5
7.5
9.75
8.5
33
25.8
125
40
127701CPS
127703CPS
11.88
15
25.5
7.5
10.75
9.5
37
25.8
150
40
127725
127704CPS
14.88
18
28.5
10
12.75
11.5
45
38.0
150
40
127738
127938CPS
14.88
18
28.5
10
12.75
11.5
45
Catalog Number Suffix Nomenclature

A = 150 degree latch
C = Captive terminal bolts 1-3/4" long, stainless steel
on Nema two hole pad
D = Bridge connector holes
E = Bridge connectors on terminals
H = .5 x 8 mounting coach bolts
J = Channel base
K = REA style backstrap with 2 bolts
L = Loadbuster hook
N = No backstrap
P = Parallel groove clamp, Bronze
R = REA backstrap with 4 bolts
S = Slotted base
Y = Cycloaliphatic insulators
Example: 127700LR = 127700 with loadbuster hook, 4-bolt REA backstrap.

Example: 127725LR = 127725 with loadbuster hook, 4-bolt REA backstrap.

Effective May 2015

M-72 station-class disconnect switch

Eaton's Cooper Power series Kearney M-72 single pole, single
throw station-class hookstick-operated disconnect switch operate
efficiently from terminal point to terminal point. Stability of the hard
drawn copper channel formed blade construction and associated
current carrying components are complemented by switch operating
hardware for operating ease, and assurance of dependability under
high thermal or momentary conditions.
Rating: Current carrying capacity of 600 A continuous and 40 kA
momentary.
increased width at hinge to assure greater rigidity. This maintains
positive alignment during closing and guards against side thrust
deflection. Blades are made of hard drawn copper, and are silverplated at contact points.
Hard Drawn Copper Contacts: Uniform conductivity is assured
through utilization of hard drawn copper in forming one-piece
Positive Blade Lock and Pryout: Blade latch prevents opening
under high momentary current conditions. Easy opening is assured
Silver to Silver Contacts: Pressure line contact on clip and circular
line contact on hinge are silver-plated. Silver plating on ends of blade
provides silver to silver contact at current transfer points. Contact
surfaces are self-cleaning, and self-wiping. Silver washers between
blade and hinge act as a bearing to assure easy blade movement
after long time exposure to contaminated atmospheres.
Figure 2. M-72 single-pole disconnect switch.
Tin-Plated Terminal Pads: Accommodates terminals for either

Steel Channel Base: Base is rugged, hot dipped galvanized formed

steel with a dead-ending hole at both ends of the base.
90 Blade Stop: Furnished with switch. Stops can be field removed

for 180 blade travel.
Vertical Mounting is Standard: Available for underhung mounting if

specified.
Insulators: Three inch B.C. ANSI standard station post.

Cycloaliphatic epoxy insulators also available. Characteristics available
upon request.
Terminal Option: Switches can be furnished with any terminal

arrangement documented. Terminals are not included in the price of
the switch.
Special Applications: Variations to meet specific customer requirements are available upon request.
Stainless Steel Loadbreak Hooks: For use with portable load
interrupter tool available upon request.
Table 3. Terminal Assemblies
230026-S6 262013-S6

TWO-BOLT TINNED BRONZE
TWO CAPTIVE STAINLESS
COMPRESSION TERMINAL
PARALLEL GROOVE CLAMP
STEEL BOLTS
Refer to Catalog 325-21
Secured with two galvanized
Factory installed, 1 3/4" long
for complete information
steel bolts. Conductor range:
bolts, accepts compression
relative to compression
#6 Solid to 397.5 MCM ASCR,
terminals.
fitting required.
500 MCM Copper or 556 MCM
Aluminum.
262224-S6
BRIDGE TYPE TWO-BOLT

CLAMP
Accepts conductor sizes
ranging from #4 Solid to
666 6 MCM ACSR or 3/4"
I.P.S. Copper.

Effective May 2015

Ratings
Reference Only
Catalog Number
3" B.C.
Insulator
T.R. No.
Approx.
Net Wt. Ibs.
110
126636
205
15.75
15
26
10
25.5
15.75
13.5
53
110
126960
205
15.75
15
26
10
27
24
15.75
13.5
53
40
150
126638
208
18.75
18
29
14
12
28.5
18.75
17.5
78
40
150
126961CPS
208
18.75
18
29
14
30
27
18.75
17.5
78
600
40
200
126640CPS
210
24.75
24
35
18
18
34.5
22.75
21.5
117
600
40
200
126962CPS
210
24.75
24
35
18
36
33
22.75
21.5
117
Base
Type
kV Max. Cont.
Design A
BIL
Mom. kA kV
M-72
15.5
600
40
P-72
15.5
600
40
M-72
25.8
600
P-72
25.8
600
M-72
38.0
P-72
38.0

C = Captive terminal bolts, 1.75" long stainless steel on NEMA two hole pad
I = Inverted construction for overhead use
L = Loadbuster hook
P = Parallel groove clamp, bronze
Example: 126636LP = 126636 with loadbuster hook and parallel groove clamps.
H
G
M-72 base dimensions
F
B
4.50
1.25
5.00 2.00
3.00
1.50
9/16 DIA. (2)
9/16 X 1 SLOTS (2)
9/16 DIA. (2)
1.00
9/16 X 1 SLOTS (2)
P-72 base dimensions

Effective May 2015

H-72 station-class disconnect switch

The rugged construction of Eaton's Cooper Power series Kearney
H-72 station-class disconnect switch assures long-term ease of
operation and dependable service.
Rating: High current carrying capacity of 1200 A continuous and 61
kA momentary.
Blade Design: Truss-type construction of formed channel with
increased width at hinge for greater rigidity. This assures minimum
side thrust deflection and positive alignment during closing. Blades
are silver-plated at contact points.
through utilization of copper bar one-piece stationary contacts and
terminal pads. This design reduces current interchange points to a
minimum.
Silver to Silver Contacts: High pressure line contact on clip and
circular line contact on hinge. Stationary contacts have silver onlays
and blade contacts are silver-plated. Contact surfaces are selfcleaning and self-wiping.
opening under high momentary current conditions. Easy opening is
assured through pryout assist.
90 Blade Stop: Furnished with switch. Stops can be field-removed
Insulators: Three inch B.C. ANSI station post. Characteristics are
available upon request.
Steel Channel Base: Base is rugged, hot dipped galvanized steel
channel.
Vertical Mounting is Standard: Also available for underhung
mounting if specified.
Figure 3. H-72 station-class disconnect switch.

Effective May 2015

Ratings
kV Max.
Cont.
Mom.
BIL
Design
kA
kV
Catalog Number
3" B.C.
Insulator
T.R. No.
15.5
1200
61
110
125931CPS
25.8
1200
61
150
125932
38.0
1200
61
200
125933CPS
Reference Only
B
Approx.
Net Wt.
Ibs.
205
13.63
15
25
10
24
27
16.75
14.88
75
208
16.63
18
28
14
27
30
20.75
18.88
100
210
22.63
24
34
18
33
36
24.75
22.88
130

B = Backstrap assembly
I = Inverted construction for overhead use
L = Loadbuster hook
Example: 125931PY = 125931 with parallel groove clamps and cycloaliphatic
insulators.

Effective May 2015

D73RB 600 A REA approved oil circuit

recloser bypass switch
Voltage: 15.5 kV and 25.8 kV
Current: 600 A Continuous
Momentary: 40 kA
BIL: 110 kV, 125 kV and 150 kV
Front Contact: Reduced area, high pressure. Hard drawn copper
blade to silver plated hard drawn copper bar front contact.
Hinge Contact: Copper blade to silver washer to hard drawn formed
copper hinge.
Insulators: 2.25" B.C. with two threaded studs.
Base: Hot dipped galvanized formed steel channel.
Backstrap: REA Standard four bolt/channel.
Blade Latch: Approximately 150
Application: With hotline studs at both ends of the switch,
a recloser needing maintenance can be easily bypassed and
disconnected. This can be done economically without disturbing
continuity of service and without the use of special tools.
Operation: With a hotstick, the switch blade is removed from its
150 positive latch and moved to a closed and positive latched
position. The opening of the recloser and removal of the hot-line
clamps makes the recloser available for servicing. When returning
the recloser to service, a pryout mechanism makes opening the
switch easy under any condition.
Figure 4. D-73RB oil circuit recloser bypass switch.

Effective May 2015

Ratings
kV Max.
Design
Cont.
A
Mom.
kA
BIL
kV
Catalog
Number
Reference Only
B
Approx.
Net Wt.
Ibs.
15.5
600
40
110
127734-9
11.88
15
27.5
30
9.75
8.5
24
25.75
36
25.8
600
40
125
127726-9
11.88
15
27.5
30
10.75
9.5
24
25.75
40
25.8
600
40
150
127727-9
14.88
18
30.5
10
30
12.75
11.5
24
25.75
48
Base Number Suffixes

C = Captive terminal bolts 1.75" long, stainless steel
H = .5 x 8 mounting coach bolts
L = Loadbuster hook
M = Without 150 degree latch

S = Slotted base
W = Without hotline studs
Example: 127727-9LS with loadbuster hook, slotted base.

Effective May 2015

D73-3P distribution-class oil circuit recloser

bypass switch for crossarm and direct pole
bracket mounting
Voltage:
15.5 kV - 110 kV BIL
25.8 kV - 125 kV and 150 kV BIL
38.0 kV - 150 kV BIL
Momentary: 40 kA Momentary
Front Contact: Reduced area, high pressure; hard drawn copper
blade to silver-plated hard drawn copper front contact.
Hinge Contact: Hard drawn copper blade to silver washer to hard
drawn formed copper hinge.
Terminals: Not included.
Versatile Mounting: Suitable for vertical or underhung mounting
and furnished either with a crossarm hanger or a pole mounting
bracket.
Insulators: 2.25" B.C. with two threaded studs.
BYPASS POSITION
Figure 5. D73-3P 600 A 3-pull oil circuit recloser bypass switch.
10
Application: Economical means of bypassing and disconnecting

pole mounted oil circuit reclosers (OCR), permitting maintenance
without disturbing continuity of service.
Features: The D73-3P switch incorporates all the design features of
Eaton's Cooper Power series Kearney D-73 switch into a compact
3-pull bypass unit. It consists of two hookstick disconnect switches
mounted on a galvanized channel with a bypass blade connected
across the top terminals of each switch.
The bypass blade can be arranged for either right hand or left hand
operation.
One mounting channel supports the entire switch for ease of
installation and uncluttered appearance. The channel can be
either cross arm mounted with a backstrap or bolted directly to a
galvanized pole mounting bracket.
A silver washer between the blade and hinge minimizes the
possibility of binding and assures ease of blade movement even
when the D73-3P switch is installed in areas with high levels of
contamination.
All switches have a positive blade lock to prevent opening under high
momentary current. Easy opening is assured through pryout assist.
The bypass blade is offset 30 from the plane of the disconnect
blades, so that the bypass switch can be operated when the switch
is mounted vertically.
Operation: The normal position of the 3-pull OCR bypass switch
is with the bypass blade open and the two disconnect switches
closed. For maintenance, testing, repair or removal of the OCR,
first the bypass switch is closed providing a parallel current path to
the OCR. After the OCR is opened, both disconnect switches are
opened. Thus, service continuity has been maintained and the OCR
is isolated from the line.
NORMAL POSITION

Effective May 2015

Ratings
Dimensions (inches)
kV Max.
Design
BIL
kV
Cont.
A
Mom.
kA
Catalog
Number
Approx
Net Wt.
(lbs.)
Pole
Mount
Units
15.5
110
600
40
127733_-6_
23.25
30
23.75
6.75
9.13
11.88
15
17.75
12.75
70
85
25.8
125
600
40
127730_-6_
23.25
30
24
9.13
11.88
15
17.75
12.75
78
93
25.8
150
600
40
127731_-6_
26.25
30
29
10
12.13
14.88
18
20.75
15.75
94
109
38.0
150
600
40
127732_-6_
26.25
30
29
10
12.13
14.88
18
20.75
15.75
94
109

L = Loadbuster hook
N = No backstrap
-6 Suffixes
L = Left handed bypass blade operation
R = Right handed bypass blade operation
LP = Left handed operation w/pole mounting bracket
RP = Right handed operation w/pole mounting bracket
Complete Part Number - LP = Live Parts Kit
Complete Part Number - BXX = Special base
Example 127733L-6LP = 127733 w/loadbuster hooks and pole mounting bracket
left handed operation.
CROSSARM
MOUNT
7.9
Catalog Number 262400-S6

POLE MOUNT
11

Effective May 2015

M95-3P station-class oil circuit recloser

bypass switch
Application: Economical means of bypassing and disconnecting oil

circuit reclosers (OCR), permitting maintenance without disturbing
continuity of service.
Voltage:
Features: The M95-3P switch incorporates all the design features of

Eaton's Cooper Power series Kearney M-72 switch into a compact
3-pull bypass unit. It consists of two hookstick disconnect switches
mounted on a galvanized channel with a bypass blade connected
across the top terminals of each switch.
15.5 kV - 110 kV BIL

25.8 kV - 150 kV BIL
38.0 kV - 200 kV BIL
Momentary: 40 kA Momentary
Hinge Contact: Hard drawn copper blade to silver washer to hard
Terminals: Not included.
Versatile Mounting: Suitable for vertical mounting.
The bypass blade can be arranged for either right hand or left hand
operation.
One mounting channel supports the entire switch for ease of
installation and uncluttered appearance.
A silver washer between the blade and hinge minimizes the
possibility of binding and assures ease of blade movement even
when the Type M95-3P switch is installed in areas with high levels
of contamination.
All switches have a positive blade lock to prevent opening under
high momentary current. Easy opening is assured through pryout
assist.
The bypass blade is offset 30 from the plane of the disconnect
blades, so that the bypass switch can be operated when the switch
is mounted vertically.
Operation: The normal position of the 3-pull OCR bypass switch
is with the bypass blade open and the two disconnect switches
closed. For maintenance, testing, repair or removal of the OCR,
first the bypass switch is closed providing a parallel current path to
the OCR. After the OCR is opened, both disconnect switches are
opened. Thus, service continuity has been maintained and the OCR
is isolated from the line.
12

Effective May 2015

Ratings
kV Max.
Design
Cont.
A
Mom.
kA
BIL
kV
Basic Switch
Catalog
Number
15.5
600
40
110
127833_-6_
Dimensions (inches), Reference only

A
Approx.
Net Wt.
lbs.
18
12-1/4
10
12
24
135
25.8
600
40
150
127831_-6_
18
12-1/4
14
12
24
180
38.0
600
40
200
127832_-6_
24
18-1/4
18
15
30
230

L = Loadbuster hook
N = No backstrap


"
-6 Suffixes
L = Left handed bypass blade operation.
R = Right handed bypass blade operation
Complete Part Number-LP = Live parts kit
Complete Part Number-BXX = Special base
Example 127833L-6P = 127833-6 w/loadbuster hooks and pole mounting bracket
left handed operation.
"
"
13

Effective May 2015

Oil circuit recloser station-class fused bypass combinations for substation mounting
Fuse Disconnect Switch
Current: 100 A or 200 A fuseholder rating, 600 A disconnect switch
rating
Fuse Interrupting Capacity: 15.5 kV and 25.8 kV, 100 or 200 A
fuseholder 7,100 A Symmetrical
Momentary: 28 kA momentary on switch
BIL: 110 kV and 150 kV BIL
Insulators: ANSI standard station post 3" B.C.
Base: Galvanized structural steel channel
Terminals: Two bolt bridge type (#262224) for #4 Sol. to 666.6 MCM
ACSR or 0.75" I.P.S. copper are included. Adapters to convert to
ANSI standard two-hole terminal pads available upon request at
additional charge.
Companion Switch
Current: 600 A continuous
Momentary: 40 kA momentary on switch
BIL: 110 kV and 150 kV BIL
Application: For use when there is a maximum requirement for
safety and continuity of service. The fused OCR bypass disconnect
combination provides safe isolation of the OCR while maintaining
service continuity with a fuse protected circuit.
Features: The cutout portion of the combination is a base mounted
HX, and will accommodate both 100 A and 200 A fuseholders. The
disconnect switches have 600 A continuous rating.
The bypass disconnect combination consists of:
1. A fuse cutout and a single pole disconnect switch mounted in
tandem on a common base.
2. A separately mounted single pole companion disconnect switch.
The fuse cutout provides the bypass component of the combination.
The disconnect switches provide for isolation of the oil circuit
recloser.
Operation: With the oil circuit recloser in the closed position (in
preparation for maintenance):
1. Place the fuseholder in hinge clip and close the cutout into the
bypass position.
2. Open the oil circuit recloser.
3. When both disconnect switches are opened, the oil circuit
recloser is isolated and bypassed.
14
Figure 6. Fused disconnect and companion switch combination.

Effective May 2015
Table 9. Fused Disconnect Switch

Ratings
kV Max.
Design
15.5
25.8
Reference Only
Fuse
Cont.
A
BIL
kV
Catalog Number
Approx
Net Wt.
Ibs.
100
110
125801
16.38
15
38.5
10
37
39.5
13.13
12.13
200
110
125802
16.38
15
38.5
10
37
39.5
13.13
12.13
100
150
125801-21
19.38
18
44.5
14
43
45.5
17.13
200
150
125802-2
19.38
18
44.5
14
43
45.5
17.13
Fuse
Interrupting
Capacity-kA
Sym.
Asym.
100
7.1
10.0
100
7.1
10.0
16.13
135
7.1
10.0
16.13
135
7.1
10.0
Table 10. Companion Switch

Ratings
Reference Only
B
Approx.
Net Wt.
Ibs.
125703-5
15.75
15
26
10
37
39.5
17
14.75
13.5
55
125728-5
18.75
18
29
14
43
45.5
23
18.75
17.5
78
kV Max.
Design
Fuse Cont.
A
BIL
kV
Catalog
Number
15.5
600
110
25.8
600
150

I = Inverted insulators
A = 2-hole Nema terminal pads
BYPASS
TERMINAL
Figure 7. Fused disconnect switch (left) and companion switch (right).
Table 11. Replacement Fuseholders

Fused Disconnect
Catalog No.
kV
Fuse
Fuse Cont.
A
Replacement Fuseholder
Catalog Number
125801
15.5
100
184201-090S6
125802
15.5
200
187201-090S6
125801-21
25.8
100
186303-090S6
125802-2
25.8
200
188303-090S6
15

Effective May 2015

HB-65/HC-65 station-class
voltage regulator bypass switch
Voltage: 8.3, 15.5, 25.8 and 38.0 kV
Momentary: 40 kA in closed position, 30 kA in
bypass position
BIL: 95 kV, 110 kV, 150 kV, and 200 kV BIL
Jaw Contacts: Reverse loop-high pressure
silver-plated copper
Hinge Contacts: Reduced area high pressure
silver-plated copper to silver-plated high conductivity bronze.
1 three-phase step regulator

three-phasedelta3 wire
Insulators: ANSI standard station post 3"

B.C.
Terminal Pads: ANSI standard two-hole, tinned
to accept copper or aluminum terminals.
Terminals: Not included. See page 21.
Application: Applicable to all voltage regulators
that can be set on neutral for the switching
operation. This includes all single-phase and
three-phase types, except three-phase induction
regulators.
Operation: One pull on the pull ring of the 600
A rated switches performs all four switching
operations in proper sequence. Opening the
bypass disconnect puts it through its four-step
automatic switching sequence of bypassing,
opening both line leads, and interrupting the
exciting current. Enforced sequenced operation
minimizes the possibility of operator error.
The 600 A switches, with the exception of the
38.0 kV, are equipped with either the arcruptor
or snaphorns. The 38.0 kV switch is available
with the snaphorn. The arcruptor has sufficient
interrupting capacity for safe interruption of the
regulator exciting current with no exposed arcing. While the means for interrupting exciting
current is mounted on the right hand blade for
mechanical reasons, the common terminal for
the series and shunt coils may be connected to
either disconnect blade.
1 single-phase regulator
single-phase2 wire
Figure 8. HB-65 station-class, 600 A

voltage regulator bypass switch.
2 single-phase regulators
three-phaseopen delta3 wire
Surge Protection: Surge protectors are available

and provide economical surge protection when
mounted across the line terminals of the bypass
switches.
three-phasewye3 or 4 wire
1 three-phase step regulator
three-phasewye3 or 4 wire
three-phasedelta3 wire
16

Effective May 2015

Ratings
Dimensions (inches), Reference Only

Base
Type
Max.
kV
BIL
kV
Cont.
Amps
*Mom.
kA
Approx.
Weight
(lbs.)
w/Arcruptor
w/Snaphorn
HB-65
8.3
95
600
40/30
1.63
19.25
12
23.13
7.5
21
24
13
12.25
79
125840
125860
w/Arcruptor
w/Snaphorn
HC-65
1.75
19.25
12
23.13
22.5
13
12.25
125821-20
125831-20
w/Arcruptor
w/Snaphorn
HB-65
1.63
22.25
15
26.13
10
24
27
15.5
14.75
125841
125861
w/Arcruptor
w/Snaphorn
HC-65
1.75
22.25
15
26.13
25.5
15.5
14.75
125822-20
125832-20
w/Arcruptor
w/Snaphorn
HB-65
1.63
25.25
18
29.13
14
26.5
29.5
19.5
18.75
125842
125862
w/Arcruptor
w/Snaphorn
HC-65
1.75
25.25
18
29.13
12
28.5
19.5
18.75
125853-20
w/Snaphorn
HB-65
1.75
31.25
24
35.13
18
33
36
23.63
22.88
125863
w/Snaphorn
HC-65
1.75
31.25
24
35.13
18
34.5
23.63
22.88
Catalog
Number
Description
125820-20
125830-20
15.5
25.8
38
110
150
200
600
600
600
40/30
40/30
40/30
97
128
175
* Disconnect Blades/Bypass Blades

I = Inverted insulators for overhead use

BASE-LP = Live parts kit
BASE-BXX = Special base number
2"
17

Effective May 2015

M-72 station-class bypass switch

Eaton's Cooper Power series Kearney M-72 station-class hookstick
operated regulator bypass switches operate efficiently from
terminal point to terminal point. Stability of the hard drawn copper
channel formed blade construction and associated current carrying
components are complemented by switch operating hardware for
operating ease, and assurance of dependability under high thermal
or momentary conditions.
momentary.
Silver to Silver Contacts: Pressure line contacts on clip and circular
line contacts on hinge are silver-plated. Silver plating on ends of
blade provides silver to silver contact at current transfer points.
Contact surfaces are self-cleaning, and self-wiping. Silver washers
between blade and hinge act as a bearing to assure easy blade
movement after long time exposure to contaminated atmospheres.
Cycloaliphatic epoxy insulators also available. Characteristics available
upon request.
steel.
specified.
18

arrangement documented. Terminals are not included in the price of
the switch.
Stainless Steel Loadbreak Hooks: For use with portable load
interrupter tool available upon request.
Application: Applicable to all voltage regulators that can be set on
neutral for the switching operation. This includes all single-phase and
three-phase types, except three-phase induction regulators.

Effective May 2015

Dimension Information (inches)
Nameplate Information
Catalog Number
Description
Maximum Voltage
kV
Max. Cont. Current

Amps
BIL kV
171506-3P
Standard Switch
18
10.25
10
27
30
15.5
600
110
171506-3PA
with Arcruptor
18
10.25
10
27
30
15.5
600
110
171506-3PS
with Snaphorn
18
10.25
10
27
30
15.5
600
110
172506-3P
Standard Switch
24
15.25
14
33
36
25.8
600
150
172506-3PA
with Arcruptor
24
15.25
14
33
36
25.8
600
150
172506-3PS
with Snaphorn
24
15.25
14
33
36
25.8
600
150

I = Inverted Insulators for overhead use
Example: 171506CP = 171506 with captive terminal
bolts and parallel groove clamps
19

Effective May 2015

H72-3P station-class bypass switch

Eaton's Cooper Power series Kearney H72-3P station-class
hookstick-operated regulator bypass switches operate efficiently
from terminal point to terminal point. Stability of the hard drawn
copper channel formed blade construction and associated current
carrying components are complemented by switch operating
hardware for operating ease, and assurance of dependability under
high thermal or momentary conditions.
momentary.
20
Silver to Silver Contacts: Pressure line contact on clip and circular

line contact on hinge are silver-plated. Silver plating on ends of blade
provides silver to silver contact at current transfer points. Contact
surfaces are self-cleaning, and self-wiping. Silver washers between
blade and hinge act as a bearing to assure easy blade movement
after long time exposure to contaminated atmospheres.
Characteristics available upon request.
steel.
specified.
arrangement documented.
Application: Applicable to all voltage regulators that can be set on
neutral for the switching operation. This includes all single-phase and
three-phase types, except three-phase induction regulators.

Effective May 2015

Dimension Information (inches)
Catalog Number
Description
Max. kV
Cont. A
Mom. kA
BIL kV
171512-3P
Standard switch
30
27
10
18
15.5
1200
61
110
171512-3PA
with Arcruptor
30
27
10
18
15.5
1200
61
110
172512-3P
Standard Switch
36
33
14
24
25.8
1200
61
150
172512-3PA
with Arcruptor
36
33
14
24
25.8
1200
61
150

Base-LP = Live parts kit
Example: 171512CP-3P = 171512-3P with captive terminal bolts and parallel groove
clamps
21

Effective May 2015

HB-65 600 A current transformer bypass

switch
Voltage: 15.5, 25.8, 38.0 and 72.5 kV
Momentary: 40 kA in closed position, 30 kA in bypass position
BIL: 95 kV, 110 kV, 200 kV, and 350 kV
Jaw Contacts: Reverse loop-high pressure silver-plated copper
Hinge Contacts: Reduced area high pressure silver-plated
copper to silver-plated high conductivity bronze.
Insulators: ANSI standard station post 3" B.C.
Terminal Pads: ANSI standard two-hole, tinned to accept copper or
aluminum terminals.
Application: For bypassing and disconnecting current transformers
without load dropping and service interruption.
Operation: One pull on the 600 A pull ring puts it through its
proper and automatic switching sequence of bypassing the current
transformer and disconnecting the transformer from service.
Figure 9. HB-65, 600 A current transformer bypass switch.
22

Effective May 2015

Dimensions (inches), Reference only
Ratings
Catalog
Number
Type
125824-20
HB-65
125844
HC-65
125825-20
HB-65
125845
HC-65
125826-20
HB-65
125846
HC-65
125828-20
HB-65
Max.
kV
BIL
KV
Cont.
A
15.5
110
600
25.8
150
600
38.0
200
600
72.5
350
600
Mom.
kA
40
1.63
22.25
15
26.13
10
24
27
15.5
14.75
30
1.75
22.25
15
26.13
10
25.5
15.5
14.75
40
1.63
25.25
18
29.13
14
26.5
29.5
19.5
18.75
30
1.75
25.25
18
29.13
14
28.5
19.5
18.75
40
1.75
31.25
24
35.13
18
33
36
23.63
22.88
30
1.75
31.25
24
35.13
18
34.5
23.63
22.88
40
2.03
49.13
42
53.13
30
51
54
35.63
34.88
Approx.
Weight
(Ibs.)
95
124
173
290

V = MOV Arrester
Base-LP = Live parts kit
Base-BXX = Special base number
HB-65 BASE
HC-65 BASE
23

Effective May 2015
D73-LT single insulator

disconnect switch (100 kV)
Eaton's Cooper Power series Kearney single
insulator disconnect switches are compact
and easy to mount directly in-line or at poletop insulator. Truss-type blade assembly for
extra strength and smooth latch mechanism
with double-tongue contact for extra contact
surface. Contacts are silver-plated, terminal
pads are tinned, structural members are
of aluminum, and all live parts are of highconductivity bronze, cast copper, or harddrawn copper.
Current Ratings: High current carrying
capacity of 600 and 900 A continuous and
40 kA momentary.
Blade Design: Truss-type construction of
formed copper bars has increased width
at hinge for greater rigidity, thus minimizing side deflection and maintaining positive
alignment when closing switch.
Minimum Current Interchanges: Uniform
conductivity is assured through utilization of
hard drawn copper bar in forming one-piece
stationary contacts and terminal pads.
Design reduces current interchange points
to a minimum.
Table 16. Nameplate Information

Nameplace Information
Catalog
Number
Max.
kV
Cont.
A
Mom.
kA
BIL
kV
127301CPS
8.3
600
40/30
110
127302CPS
8.3
900
40/30
110

L = Loadbuster hook
D73-LT single insulator

disconnect switch (150 kV)
Eaton's Cooper Power series Kearney single
insulator disconnect switches are compact
and easy to mount directly in-line or at poletop insulator. Truss-type blade assembly for
extra strength and smooth latch mechanism with double-tongue contact for extra
contact surface. Contacts are silver-plated,
terminal pads are tinned, structural members are of aluminum, and all live parts are
of high-conductivity bronze, cast copper, or
hard-drawn copper.
Current Ratings: High current carrying
capacity of 600 and 900 A continuous and
40 kA momentary.
Blade Design: Truss-type construction of
formed copper bars has increased width
at hinge for greater rigidity, thus minimizing side deflection and maintaining positive
alignment when closing switch.
Minimum Current Interchanges: Uniform
conductivity is assured through utilization
of hard drawn copper bar in forming onepiece stationary contacts and terminal pads.
Design reduces current interchange points
to a minimum.
24
Table 17. Nameplate Information

Catalog
Number
Max.
kV
Cont.
A
Mom.
kA
BIL
kV
127303CPS
25.8
600
40
150
127304CPS
25.8
900
40
150
127305CPS
38.0
600
40
150
127306CPS
38.0
900
40
150

L = Loadbuster hook


Effective May 2015
DLT distribution-class inline tension

disconnect switch
Voltage: 25.8 kV 150 kV BIL
17.00"

Hinge Contact: Hard drawn copper blade to silver wash to hard
Application: Provides means for line sectionalizing or isolating
equipment on distribution circuits.
Mounting: The DLT disconnect switch is easily installed in line with
the conductor freeing up valuable space on the pole and crossarm.
25.50"
Table 18. Ordering Information

Ratings
Catalog
Number
Max.
Voltage
Cont.
A
BIL
kV
Mom.
kA
3 Second
kA
127750
25.8 kV
600
150
40
25
127751
25.8 kV
900
150
40
25

A 150 degree latch
C Captive terminal bolts, 1.75" long, stainless steel
D Bridge connector holes
E Bridge connectors on terminals
L Loadbuster hook
P Parallel groove clamp, bronze
Base-LP Live parts kit
25

Effective May 2015
D73-CD distribution-class
single insulator disconnect switch
Voltage: 15.5, 27.0, and 38.0 kV.
Hinge Contact: Hard drawn copper blade to silver wash to hard
Application: Provides means for line sectionalizing or isolating
equipment on distribution circuits.
Mounting: The D73-CD disconnect switch is easily installed with the
included crossarm bracket much like a standard cutout.

Ratings
Catalog
Number
Max. Voltage
Cont.
A
BIL
kV
Mom.
kA
3 Second
kA
X Length
(inches)
127740
15.5 kV
600
110
40
25
25.5
127741
15.5 kV
900
110
40
25
25.5
127742
27.0 kV
600
125
40
25
25.5
127743CPS
27.0 kV
900
125
40
25
25.5
127744
27.0 kV
600
150
40
25
28.5
127745
27.0 kV
900
150
40
25
28.5
127746
38.0 kV
600
170
40
25
28.5
127747
38.0 kV
900
170
40
25
28.5

A 150 degree Latch
C Captive terminal bolts, 1.75 long, stainless steel
D Bridge connector holes
E Bridge connectors on terminals
L Loadbuster hook
P Parallel groove clamp, bronze
X Extended mounting bracket
Base-LP Live parts kit
26


Effective May 2015
27

Effective May 2015
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eatons Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
2015 Eaton
All Rights Reserved
Printed in USA
Publication No. CA008006EN
Eaton, Cooper Power, and Kearney are

valuable trademarks of Eaton in the U.S. and
other countries. You are not permitted to use
these trademarks without the prior written
consent of Eaton.
ANSI is a registered trademark of American
National Standards Institute.
NEMA is a registered trademark of National
Electrical Manufacturers Association.
For Eatons Cooper Power series disconnect

and bypass switches product information
call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.

CA 008006 en

Uploaded by

Copyright:

Available Formats

CA 008006 en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CA 008006 en

Uploaded by

Copyright:

Available Formats

Switches

Effective May 2015

Disconnect and oil circuit recloser

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

Effective May 2015

Eaton's Kearney regulator and current transformer bypass switches

D-73 distribution-class disconnect switch

Figure 1. D-73 single-pole disconnect switch.

Tin-Plated Terminal Pads: Accommodate terminals for either

Table 1. Terminal Assemblies

TWO-BOLT TINNED BRONZE

TWO CAPTIVE STAINLESS

BRIDGE TYPE TWO-BOLT

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

Effective May 2015

Table 2. Dimensions and Ordering Information

Catalog Number Suffix Nomenclature

Example: 127700LR = 127700 with loadbuster hook, 4-bolt REA backstrap.

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

M-72 station-class disconnect switch

Figure 2. M-72 single-pole disconnect switch.

Tin-Plated Terminal Pads: Accommodates terminals for either

Steel Channel Base: Base is rugged, hot dipped galvanized formed

90 Blade Stop: Furnished with switch. Stops can be field removed

Vertical Mounting is Standard: Available for underhung mounting if

Insulators: Three inch B.C. ANSI standard station post.

Terminal Option: Switches can be furnished with any terminal

Table 3. Terminal Assemblies

BRIDGE TYPE TWO-BOLT

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

Effective May 2015

Table 4. Dimensions and Ordering Information

Catalog Number Suffix Nomenclature

M-72 base dimensions

9/16 X 1 SLOTS (2)

9/16 DIA. (2)

9/16 X 1 SLOTS (2)

P-72 base dimensions

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

H-72 station-class disconnect switch

Figure 3. H-72 station-class disconnect switch.

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

Effective May 2015

Table 5. Dimensions and Ordering Information

Catalog Number Suffix Nomenclature

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

D73RB 600 A REA approved oil circuit

Figure 4. D-73RB oil circuit recloser bypass switch.

Catalog Data CA008006EN

Disconnect and oil circuit recloser bypass switches; regulator

Effective May 2015

Table 6. Dimensions and Ordering Information