300 115
300 115
QUESTION NO: 1
What is the maximum number of switches that can be stacked using Cisco StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13
Answer: D
Explanation:
QUESTION NO: 2
A network engineer wants to add a new switch to an existing switch stack. Which configuration
must be added to the new switch before it can be added to the switch stack?
A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information
Answer: A
Explanation:
QUESTION NO: 3
What percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100
QUESTION NO: 4
Refer to the exhibit.
Which set of configurations will result in all ports on both switches successfully bundling into an
EtherChannel?
A. switch1
channel-group 1 mode active
switch2
channel-group 1 mode auto
B. switch1
channel-group 1 mode desirable
switch2
channel-group 1 mode passive
C. switch1
"Pass Any Exam. Any Time." - www.actualtests.com
QUESTION NO: 5
Refer to the exhibit.
How can the traffic that is mirrored out the GigabitEthernet0/48 port be limited to only traffic that is
received or transmitted in VLAN 10 on the GigabitEthernet0/1 port?
A. Change the configuration for GigabitEthernet0/48 so that it is a member of VLAN 10.
B. Add an access list to GigabitEthernet0/48 to filter out traffic that is not in VLAN 10.
C. Apply the monitor session filter globally to allow only traffic from VLAN 10.
D. Change the monitor session source to VLAN 10 instead of the physical interface.
Answer: C
Explanation:
QUESTION NO: 6
Refer to the exhibit.
A network engineer wants to analyze all incoming and outgoing packets for an interface that is
connected to an access switch. Which three items must be configured to mirror traffic to a packet
sniffer that is connected to the distribution switch? (Choose three.)
A. A monitor session on the distribution switch with a physical interface as the source and the
remote SPAN VLAN as the destination
B. A remote SPAN VLAN on the distribution and access layer switch
C. A monitor session on the access switch with a physical interface source and the remote SPAN
VLAN as the destination
D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and
physical interface as the destination
E. A monitor session on the access switch with a remote SPAN VLAN source and the physical
interface as the destination
F. A monitor session on the distribution switch with a physical interface as the source and a
physical interface as the destination
Answer: B,C,D
Explanation:
QUESTION NO: 7
After an EtherChannel is configured between two Cisco switches, interface port channel 1 is in the
down/down state. Switch A is configured with channel-group 1 mode active, while Switch B is
configured with channel-group 1 mode desirable. Why is the EtherChannel bundle not working?
A. The switches are using mismatched EtherChannel negotiation modes.
B. The switch ports are not configured in trunking mode.
C. LACP priority must be configured on both switches.
D. The channel group identifier must be different for Switch A and Switch B.
Answer: A
QUESTION NO: 8
An EtherChannel bundle has been established between a Cisco switch and a corporate web
server. The network administrator noticed that only one of the EtherChannel links is being utilized
to reach the web server. What should be done on the Cisco switch to allow for better
EtherChannel utilization to the corporate web server?
A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the
EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the
server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.
Answer: E
Explanation:
QUESTION NO: 9
Interface FastEthernet0/1 is configured as a trunk interface that allows all VLANs. This command
is configured globally:
QUESTION NO: 10
A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the
diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery
Protocol, but it has several routing neighbor relationships. What would cause the output to show
only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote
devices.
Answer: A
Explanation:
QUESTION NO: 11
After the implementation of several different types of switches from different vendors, a network
engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible.
Which vendor-neutral protocol could be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol
Answer: B
Explanation:
QUESTION NO: 12
Several new switches have been added to the existing network as VTP clients. All of the new
switches have been configured with the same VTP domain, password, and version. However,
VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be
done to fix this?
A. Remove the VTP domain name from all switches with "null" and then replace it with the new
"Pass Any Exam. Any Time." - www.actualtests.com
QUESTION NO: 13
After implementing VTP, the extended VLANs are not being propagated to other VTP switches.
What should be configured for extended VLANs?
A. VTP does not support extended VLANs and should be manually added to all switches.
B. Enable VTP version 3, which supports extended VLAN propagation.
C. VTP authentication is required when using extended VLANs because of their ability to cause
network instability.
D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to
different IOS versions when extended VLANs are in use.
Answer: B
Explanation:
QUESTION NO: 14
Refer to the exhibit.
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C
receives VLAN information from the VTP server Switch A, but Switch B does not receive any
VLAN information. What is the most probable cause of this behavior?
QUESTION NO: 15
Refer to the exhibit.
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch B has
all VLANs, but Switch C is not receiving traffic from certain VLANs. What would cause this issue?
A. A VTP authentication mismatch occurred between Switch A and Switch B.
B. The VTP revision number of Switch B is higher than that of Switch A.
C. VTP pruning is configured globally on all switches and it removed VLANs from the trunk
interface that is connected to Switch C.
D. The trunk between Switch A and Switch B is misconfigured.
Answer: C
Explanation:
QUESTION NO: 16
After the recent upgrade of the switching infrastructure, the network engineer notices that the port
roles that were once "blocking" are now defined as "alternate" and "backup." What is the reason
for this change?
A. The new switches are using RSTP instead of legacy IEEE 802.1D STP.
"Pass Any Exam. Any Time." - www.actualtests.com
QUESTION NO: 17
An administrator recently configured all ports for rapid transition using PortFast. After testing, it
has been determined that several ports are not transitioning as they should. What is the reason for
this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.
Answer: C
Explanation:
QUESTION NO: 18
Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Answer: C
Explanation:
QUESTION NO: 19
What effect does the mac address-table aging-time 180 command have on the MAC addresstable?
"Pass Any Exam. Any Time." - www.actualtests.com
10
QUESTION NO: 20
While working in the core network building, a technician accidently bumps the fiber connection
between two core switches and damages one of the pairs of fiber. As designed, the link was
placed into a non-forwarding state due to a fault with UDLD. After the damaged cable was
replaced, the link did not recover. What solution allows the network switch to automatically recover
from such an issue?
A. macros
B. errdisable autorecovery
C. IP Event Dampening
D. command aliases
E. Bidirectional Forwarding Detection
Answer: B
Explanation:
QUESTION NO: 21
A network engineer deployed a switch that operates the LAN base feature set and decides to use
the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during
peak working hours. What is the root cause of this issue?
A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.
Answer: C
Explanation:
11
QUESTION NO: 23
Refer to the exhibit.
12
QUESTION NO: 24
A network engineer tries to configure storm control on an EtherChannel bundle. What is the result
of the configuration?
A. The storm control settings will appear on the EtherChannel, but not on the associated physical
ports.
B. The configuration will be rejected because storm control is not supported for EtherChannel.
C. The storm control configuration will be accepted, but will only be present on the physical
interfaces.
D. The settings will be applied to the EtherChannel bundle and all associated physical interfaces.
Answer: D
Explanation:
QUESTION NO: 25
What is the function of NSF?
A. forward traffic simultaneously using both supervisors
B. forward traffic based on Cisco Express Forwarding
C. provide automatic failover to back up supervisor in VSS mode
D. provide nonstop forwarding in the event of failure of one of the member supervisors
Answer: D
Explanation:
QUESTION NO: 26
After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD
packets. This port continues to reestablish until after eight failed retries. The port then transitions
into the errdisable state. Which option describes what causes the port to go into the errdisable
state?
"Pass Any Exam. Any Time." - www.actualtests.com
13
QUESTION NO: 27
After reviewing UDLD status on switch ports, an engineer notices that the." Which statement
describes what this indicates about the status of the port?
A. The port is fully operational and no known issues are detected.
B. The bidirectional status of "unknown" indicates that the port will go into the disabled state
because it stopped receiving UDLD packets from its neighbor.
C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.
D. The UDLD port is placed in the "unknown" state for 5 seconds until the next UDLD packet is
received on the interface.
Answer: A
Explanation:
QUESTION NO: 28
Pilot testing of the new switching infrastructure finds that when the root port is lost, STP
immediately replaces the root port with an alternative root port. Which spanning-tree technology is
used to accomplish backup root port selection?
A. PVST+
B. PortFast
C. BackboneFast
D. UplinkFast
E. Loop Guard
F. UDLD
Answer: D
Explanation:
14
QUESTION NO: 30
A network engineer must set the load balance method on an existing port channel. Which action
must be done to apply a new load balancing method?
A. Configure the new load balancing method using port-channel load-balance.
B. Adjust the switch SDM back to "default".
C. Ensure that IP CEF is enabled globally to support all load balancing methods.
D. Upgrade the PFC to support the latest load balancing methods.
Answer: A
Explanation:
QUESTION NO: 31
Refer to the exhibit.
15
QUESTION NO: 32
While doing network discovery using Cisco Discovery Protocol, it is found that rapid error tracking
is not currently enabled. Which option must be enabled to allow for enhanced reporting
mechanisms using Cisco Discovery Protocol?
A. Cisco Discovery Protocol version 2
B. Cisco IOS Embedded Event Manager
C. logging buffered
D. Cisco Discovery Protocol source interface
E. Cisco Discovery Protocol logging options
Answer: A
Explanation:
QUESTION NO: 33
Which technique allows specific VLANs to be strictly permitted by the administrator?
A. VTP pruning
B. transparent bridging
C. trunk allowed VLANs
D. VLAN access-list
E. L2P tunneling
Answer: C
Explanation:
16
QUESTION NO: 34
For security reasons, the IT manager has prohibited users from dynamically establishing trunks
with their associated upstream switch. Which two actions can prevent interface trunking? (Choose
two.)
A. Configure trunk and access interfaces manually.
B. Disable DTP on a per interface basis.
C. Apply BPDU guard and BPDU filter.
D. Enable switchport block on access ports.
Answer: A,B
Explanation:
QUESTION NO: 35
Which two protocols can be automatically negotiated between switches for trunking? (Choose
two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q
Answer: C,F
Explanation:
QUESTION NO: 36
A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the
new switch is not receiving the list of VLANs from the server. Which action resolves this problem?
A. Reload the new switch.
B. Restart the VTP process on the new switch.
C. Reload the VTP server.
D. Verify connected trunk ports.
"Pass Any Exam. Any Time." - www.actualtests.com
17
QUESTION NO: 37
After configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer
notices that none of the VTP clients are receiving the updates. What is the problem?
A. The VTP server must be reloaded.
B. The VTP version number must be set to version 3.
C. After each update to the VTP server, it takes up to 4 hours propagate.
D. VTP must be stopped and restarted on the server.
E. Another switch in the domain has a higher revision number than the server.
Answer: B
Explanation:
QUESTION NO: 38
A network engineer is extending a LAN segment between two geographically separated data
centers. Which enhancement to a spanning-tree design prevents unnecessary traffic from crossing
the extended LAN segment?
A. Modify the spanning-tree priorities to dictate the traffic flow.
B. Create a Layer 3 transit VLAN to segment the traffic between the sites.
C. Use VTP pruning on the trunk interfaces.
D. Configure manual trunk pruning between the two locations.
Answer: C
Explanation:
QUESTION NO: 39
The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed
to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is
issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the
problem?
18
QUESTION NO: 40
When you design a switched network using VTPv2, how many VLANs can be used to carry user
traffic?
A. 1000
B. 1001
C. 1024
D. 2048
E. 4095
F. 4096
Answer: B
Explanation:
QUESTION NO: 41
What does the command vlan dot1q tag native accomplish when configured under global
configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.
Answer: D
Explanation:
QUESTION NO: 42
19
QUESTION NO: 43
A manager tells the network engineer to permit only certain VLANs across a specific trunk
interface. Which option can be configured to accomplish this?
A. allowed VLAN list
B. VTP pruning
C. VACL
D. L2P tunneling
Answer: A
Explanation:
QUESTION NO: 44
For client server failover purposes, the application server team has indicated that they must not
have the standard 30 second delay before their switchport enters a forwarding state. For their
disaster recovery feature to operate successfully, they require the switchport to enter a forwarding
state immediately. Which spanning-tree feature satisfies this requirement?
A. Rapid Spanning-Tree
B. Spanning-Tree Timers
C. Spanning-Tree FastPort
D. Spanning-Tree PortFast
E. Spanning-Tree Fast Forward
Answer: D
20
QUESTION NO: 45
Which command does a network engineer use to verify the spanning-tree status for VLAN 10?
A. switch# show spanning-tree vlan 10
B. switch# show spanning-tree bridge
C. switch# show spanning-tree brief
D. switch# show spanning-tree summary
E. switch# show spanning-tree vlan 10 brief
Answer: A
Explanation:
QUESTION NO: 46
A new network that consists of several switches has been connected together via trunking
interfaces. If all switches currently have the default VTP domain name "null", which statement
describes what happens when a domain name is configured on one of the switches?
A. The switch with the non-default domain name restores back to "null" upon reboot.
B. Switches with higher revision numbers does not accept the new domain name.
C. VTP summary advertisements are sent out of all ports with the new domain name.
D. All other switches with the default domain name become VTP clients.
Answer: C
Explanation:
QUESTION NO: 47
A network engineer is setting up a new switched network. The network is expected to grow and
add many new VLANs in the future. Which Spanning Tree Protocol should be used to reduce
switch resources and managerial burdens that are associated with multiple spanning-tree
instances?
A. RSTP
B. PVST
"Pass Any Exam. Any Time." - www.actualtests.com
21
QUESTION NO: 48
Which statement about the use of SDM templates in a Cisco switch is true?
A. SDM templates are used to configure system resources in the switch to optimize support for
specific features, depending on how the switch is used in the network.
B. SDM templates are used to create Layer 3 interfaces (switch virtual interfaces) to permit hosts
in one VLAN to communicate with hosts in another VLAN.
C. SDM templates are used to configure ACLs that protect networks and specific hosts from
unnecessary or unwanted traffic.
D. SDM templates are used to configure a set of ACLs that allows the users to manage the flow of
traffic handled by the route processor.
E. SDM templates are configured by accessing the switch using the web interface.
Answer: A
Explanation:
QUESTION NO: 49
Which SDM template disables routing and supports the maximum number of unicast MAC
addresses?
A. VLAN
B. access
C. default
D. routing
Answer: A
Explanation:
QUESTION NO: 50
22
QUESTION NO: 51
In a Cisco switch, what is the default period of time after which a MAC address ages out and is
discarded?
A. 100 seconds
B. 180 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Explanation:
QUESTION NO: 52
If a network engineer applies the command mac-address-table notification mac-move on a Cisco
switch port, when is a syslog message generated?
A. A MAC address or host moves between different switch ports.
B. A new MAC address is added to the content-addressable memory.
C. A new MAC address is removed from the content-addressable memory.
D. More than 64 MAC addresses are added to the content-addressable memory.
Answer: A
Explanation:
QUESTION NO: 53
"Pass Any Exam. Any Time." - www.actualtests.com
23
QUESTION NO: 54
What is the default value for the errdisable recovery interval in a Cisco switch?
A. 30 seconds
B. 100 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Explanation:
QUESTION NO: 55
Which statement about LLDP-MED is true?
A. LLDP-MED is an extension to LLDP that operates between endpoint devices and network
devices.
B. LLDP-MED is an extension to LLDP that operates only between network devices.
C. LLDP-MED is an extension to LLDP that operates only between endpoint devices.
D. LLDP-MED is an extension to LLDP that operates between routers that run BGP.
Answer: A
Explanation:
QUESTION NO: 56
Which statement about Cisco devices learning about each other through Cisco Discovery Protocol
"Pass Any Exam. Any Time." - www.actualtests.com
24
QUESTION NO: 57
Which option lists the information that is contained in a Cisco Discovery Protocol advertisement?
A. native VLAN IDs, port-duplex, hardware platform
B. native VLAN IDs, port-duplex, memory errors
C. native VLAN IDs, memory errors, hardware platform
D. port-duplex, hardware platform, memory errors
Answer: A
Explanation:
QUESTION NO: 58
Which option describes a limitation of LLDP?
A. LLDP cannot provide information about VTP.
B. LLDP does not support TLVs.
C. LLDP can discover only Windows servers.
D. LLDP can discover up to two devices per port.
Answer: A
Explanation:
QUESTION NO: 59
Which statement about the UDLD protocol is true?
25
QUESTION NO: 60
Which option lists the modes that are available for configuring UDLD on a Cisco switch?
A. normal and aggressive
B. active and aggressive
C. normal and active
D. normal and passive
E. normal and standby
Answer: A
Explanation:
QUESTION NO: 61
What is the default interval at which Cisco devices send Cisco Discovery Protocol
advertisements?
A. 30 seconds
B. 60 seconds
C. 120 seconds
D. 300 seconds
Answer: B
Explanation:
26
QUESTION NO: 63
Which VTP mode is needed to configure an extended VLAN, when a switch is configured to use
VTP versions 1 or 2?
A. transparent
B. client
C. server
D. Extended VLANs are only supported in version 3 and not in versions 1 or 2.
Answer: D
Explanation:
QUESTION NO: 64
What is the size of the VLAN field inside an 802.1q frame?
A. 8-bit
B. 12-bit
C. 16-bit
D. 32-bit
Answer: B
Explanation:
QUESTION NO: 65
"Pass Any Exam. Any Time." - www.actualtests.com
27
QUESTION NO: 66
Refer to the exhibit.
Which option shows the expected result if a show vlan command is issued?
A)
B)
28
C)
D)
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
Answer: A
Explanation:
29
QUESTION NO: 68
In which portion of the frame is the 802.1q header found?
A. within the Ethernet header
B. within the Ethernet payload
C. within the Ethernet FCS
D. within the Ethernet source MAC address
Answer: A
Explanation:
QUESTION NO: 69
Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a
switch?
A. VLANs 1-1001
B. VLANs 1-4094
C. VLANs 2-1001
D. VLANs 2-4094
Answer: C
Explanation:
30
QUESTION NO: 71
Refer to the exhibit.
The users in an engineering department that connect to the same access switch cannot access
the network. The network engineer found that the engineering VLAN is missing from the database.
Which action resolves this problem?
A. Disable VTP pruning and disable 802.1q.
B. Update the VTP revision number.
C. Change VTP mode to server and enable 802.1q.
D. Enable VTP pruning and disable 802.1q.
Answer: C
Explanation:
QUESTION NO: 72
Refer to the exhibit.
31
The network switches for two companies have been connected and manually configured for the
required VLANs, but users in company A are not able to access network resources in company B
when DTP is enabled. Which action resolves this problem?
A. Delete vlan.dat and ensure that the switch with lowest MAC address is the VTP server.
B. Disable DTP and document the VTP domain mismatch.
C. Manually force trunking with switchport mode trunk on both switches.
D. Enable the company B switch with the vtp mode server command.
Answer: C
Explanation:
32
QUESTION NO: 74
Which statement about using native VLANs to carry untagged frames is true?
A. Cisco Discovery Protocol version 2 carries native VLAN information, but version 1 does not.
B. Cisco Discovery Protocol version 1 carries native VLAN information, but version 2 does not.
C. Cisco Discovery Protocol version 1 and version 2 carry native VLAN information.
D. Cisco Discovery Protocol version 3 carries native VLAN information, but versions 1 and 2 do
not.
Answer: A
Explanation:
QUESTION NO: 75
Refer to the exhibit.
A multilayer switch has been configured to send and receive encapsulated and tagged frames.
VLAN 2013 on the multilayer switch is configured as the native VLAN. Which option is the cause
of the spanning-tree error?
"Pass Any Exam. Any Time." - www.actualtests.com
33
QUESTION NO: 76
A network engineer must improve bandwidth and resource utilization on the switches by stopping
the inefficient flooding of frames on trunk ports where the frames are not needed. Which Cisco
IOS feature can be used to achieve this task?
A. VTP pruning
B. access list
C. switchport trunk allowed VLAN
D. VLAN access-map
Answer: A
Explanation:
QUESTION NO: 77
Which action allows a network engineer to limit a default VLAN from being propagated across all
trunks?
A. Upgrade to VTP version 3 for advanced feature set support.
B. Enable VTP pruning on the VTP server.
C. Manually prune default VLAN with switchport trunk allowed vlans remove.
D. Use trunk pruning vlan 1.
Answer: C
Explanation:
QUESTION NO: 78
What is required for a LAN switch to support 802.1q Q-in-Q encapsulation?
34
QUESTION NO: 79
Refer to the exhibit.
How many bytes are added to each frame as a result of the configuration?
A. 4-bytes except the native VLAN
B. 8-bytes except the native VLAN
C. 4-bytes including native VLAN
D. 8-bytes including native VLAN
Answer: A
Explanation:
QUESTION NO: 80
A network engineer configured a fault-tolerance link on Gigabit Ethernet links G0/1, G0/2, G0/3,
and G0/4 between two switches using Ethernet port-channel. Which action allows interface G0/1
to always actively forward traffic in the port-channel?
A. Configure G0/1 as half duplex and G0/2 as full duplex.
B. Configure LACP port-priority on G0/1 to 1.
C. Configure LACP port-priority on G0/1 to 65535.
D. LACP traffic goes through G0/4 because it is the highest interface ID.
Answer: B
"Pass Any Exam. Any Time." - www.actualtests.com
35
QUESTION NO: 81
Which statement about the use of PAgP link aggregation on a Cisco switch that is running Cisco
IOS Software is true?
A. PAgP modes are off, auto, desirable, and on. Only the combinations auto-desirable, desirabledesirable, and on-on allow the formation of a channel.
B. PAgP modes are active, desirable, and on. Only the combinations active-desirable, desirabledesirable, and on-on allow the formation of a channel.
C. PAgP modes are active, desirable, and on. Only the combinations active-active, desirabledesirable, and on-on allow the formation of a channel.
D. PAgP modes are off, active, desirable, and on. Only the combinations auto-auto, desirabledesirable, and on-on allow the formation of a channel.
Answer: A
Explanation:
QUESTION NO: 82
Refer to the exhibit.
36
QUESTION NO: 83
Refer to the exhibit.
37
Users of PC-1 experience slow connection when a webpage is requested from the server. To
increase bandwidth, the network engineer configured an EtherChannel on interfaces Fa1/0 and
Fa0/1 of the server farm switch, as shown here:
However, traffic is still slow. Which action can the engineer take to resolve this issue?
A. Disable EtherChannel load balancing.
B. Upgrade the switch IOS to IP services image.
C. Change the load-balance method to dst-mac.
D. Contact Cisco TAC to report a bug on the switch.
Answer: C
Explanation:
QUESTION NO: 84
A network engineer changed the port speed and duplex setting of an existing EtherChannel
bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the
bundle?
A. PAgP changes the port speed and duplex for all ports in the bundle.
38
QUESTION NO: 85
Which statement about using EtherChannel on Cisco IOS switches is true?
A. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 8
Gbps only for Gigabit EtherChannel.
B. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or
8 Gbps only for Gigabit EtherChannel.
C. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or
16 Gbps only for Gigabit EtherChannel.
D. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel.
The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or
10 Gbps only for Gigabit EtherChannel.
Answer: A
Explanation:
QUESTION NO: 86
Refer to the exhibit.
39
QUESTION NO: 87
What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives
802.1d BPDU?
A. 802.1d does not understand RSTP BPDUs because they are different versions, but when a
RSTP switch receives an 802.1d BPDU, it responds with an 802.1d BPDU and eventually the two
switches run 802.1d to communicate.
"Pass Any Exam. Any Time." - www.actualtests.com
40
QUESTION NO: 88
When two MST instances (MST 1 and MST 2) are created on a switch, what is the total number of
spanning-tree instances running on the switch?
A. 1
B. 2
C. 3
D. 4
Answer: C
Explanation:
QUESTION NO: 89
Refer to the exhibit.
41
f1/0 and f1/1 have the same end-to-end path cost to the designated bridge. Which action is
needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3
uses switchport f1/1 as a primary port?
A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.
B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.
C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.
D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.
Answer: C
Explanation:
QUESTION NO: 90
Refer to the exhibit.
42
QUESTION NO: 91
Refer to the exhibit.
43
All ports are members of VLAN 10. Considering the default cost of upstream bridges to the root
bridge is equal, which option will be the new root port for VLAN 10?
A. interface f0/13
B. interface f0/14
C. interface f0/15
D. interface f0/21
Answer: D
Explanation:
QUESTION NO: 92
A network engineer is trying to deploy a PC on a network. The engineer observes that when the
PC is connected to the network, it takes 30 to 60 seconds for the PC to see any activity on the
network interface card. Which Layer 2 enhancement can be used to eliminate this delay?
A. Configure port duplex and speed to auto negotiation.
B. Configure port to duplex full and speed 1000.
C. Configure spanning-tree portfast.
D. Configure no switchport.
Answer: C
"Pass Any Exam. Any Time." - www.actualtests.com
44
QUESTION NO: 93
A network engineer configured an Ethernet switch using these commands.
Which statement about the spanning-tree portfast feature on the switch is true?
A. If an interface is enabled for portfast receives BDPU, the port goes through the spanning-tree
listening, learning, and forwarding states.
B. If an interface is enabled for portfast receives BDPU, the port does not go through the
spanning-tree listening, learning, and forwarding states.
C. If an interface is enabled for portfast receives BDPU, the port is shut down immediately.
D. If an interface is enabled for portfast receives BDPU, the port goes into the spanning-tree
inconsistent state.
Answer: A
Explanation:
QUESTION NO: 94
Which statement describes what happens when a port configured with root guard receives a
superior BPDU?
A. The port goes into errdisabled state and stops forwarding traffic.
B. The port goes into BPDU-inconsistent state and stops forwarding traffic.
C. The port goes into loop-inconsistent state and stops forwarding traffic.
D. The port goes into root-inconsistent state and stops forwarding traffic.
Answer: D
Explanation:
QUESTION NO: 95
"Pass Any Exam. Any Time." - www.actualtests.com
45
QUESTION NO: 96
What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an
EtherChannel for the virtual switch link?
A. 4
B. 6
C. 8
D. 12
Answer: C
Explanation:
QUESTION NO: 97
Which statement describes what happens if all VSL connections between the virtual switch
members are lost?
A. Both virtual switch members cease to forward traffic.
B. The VSS transitions to the dual active recovery mode, and both virtual switch members
continue to forward traffic independently.
C. The virtual switch members reload.
D. The VSS transitions to the dual active recovery mode, and only the new active virtual switch
continues to forward traffic.
Answer: D
Explanation:
46
47
48
49
50
51
52
53
Answer: There are two ways to configure interVLAN routing in this case:
+ Use RouterC as a router on a stick and SwitchC as a pure Layer2 switch. Trunking must be
established between RouterC and SwitchC.
+ Only use SwitchC for interVLAN routing without using RouterC, SwitchC should be configured
as a Layer 3 switch (which supports ip routing function as a router). No trunking requires.
The question clearly states No trunking has been configured on RouterC so RouterC does not
contribute to interVLAN routing of hosts H1 & H2 -> SwitchC must be configured as a Layer 3
switch with SVIs for interVLAN routing.
We should check the default gateways on H1 & H2. Click on H1 and H2 and type the ipconfig
command to get their default gateways.
Answer: \>ipconfig
We will get the default gateways as follows:
Host1:
+ Default gateway: 190.200.250.33
Host2:
+ Default gateway: 190.200.250.65
Now we have enough information to configure SwitchC (notice the EIGRP AS in this case is 650)
Note: VLAN2 and VLAN3 were created and gi0/10, gi0/11 interfaces were configured as access
ports so we dont need to configure them in this sim.
SwitchC# configure terminal
SwitchC(config)# int gi0/1
SwitchC(config-if)#no switchport -> without using this command, the simulator does not let you
assign IP address on Gi0/1 interface.
SwitchC(config-if)# ip address 10.10.10.2 255.255.255.0 ->RouterC has used IP 10.10.10.1 so
54
55
56
57
You are connecting the New_Switch to the LAN topology; the switch has been partially configured
and you need to complete the rest of configuration to enable PC1 communication with PC2. Which
of the configuration is correct?
58
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
"Pass Any Exam. Any Time." - www.actualtests.com
59
So we know that the VTP domain must be CCNP. This leaves only choice D and E. We also see
from the topology diagram that eth 0/0 of the new switch connects to a PC in VLNA 100, so we
know that this port must be an access port in VLAN 100, leaving only choice D as correct. Note
that the VTP versions supported in this network are 1, 2, 3 so either VTP version 2 or 3 can be
configured on the new switch.
60
61
62
Refer to the configuration. For which configured VLAN are untagged frames sent over trunk
between SW1 and SW2?
A. VLAN1
B. VLAN 99
C. VLAN 999
D. VLAN 40
E. VLAN 50
F. VLAN 200
G. VLAN 300
Answer: B
Explanation:
The native VLAN is used for untagged frames sent along a trunk. By issuing the show interface
trunk command on SW1 and SW2 we see the native VLAN is 99.
63
64
65
You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to
configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary
root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?
A. Configure VLAN 500 & VLAN 600 on both SW1 & SW2
B. Configure VLAN 500 and VLAN 600 on SW1 only
C. Configure VLAN 500 and VLAN 600 on SW2 only
D. Configure VLAN 500 and VLAN 600 on SW1 ,SW2 and SW4
"Pass Any Exam. Any Time." - www.actualtests.com
66
67
68
69
70
Examine the VTP configuration. You are required to configure private VLANs for a new server
deployment connecting to the SW4 switch. Which of the following configuration steps will allow
creating private VLANs?
A. Disable VTP pruning on SW1 only
B. Disable VTP pruning on SW2 only
C. Disable VTP pruning on SW4 only
D. Disable VTP pruning on SW2, SW4 and New_Switch
E. Disable VTP pruning on New_Switch and SW4 only.
Answer: C
Explanation:
To create private VLANs, you will need to only disable pruning on the switch that contains the
private VLANs. In this case, only SW4 will connect to servers in a private VLAN.
71
72
73
74
75
76
Which login credentials are required when connecting to the console port in this output?
A. none required
B. username cisco with password cisco
C. no username with password linepass
D. login authentication default
Answer: A
Explanation:
77
When a network administrator is attempting an SSH connection to the device, in which order does
the device check the login credentials?
A. RADIUS server, local username, line password
B. RADIUS server, line password, local username
C. Line password, local username, RADIUS server
D. Line password, RADIUS server, local username
Answer: A
Explanation:
78
79
80
81
82
83
84
85
86
87
88
Which option describes the reason for this message in a GLBP configuration?
A. Unavailable GLBP active forwarder
B. Incorrect GLBP IP address
C. HSRP configured on same interface as GLBP
D. Layer 2 loop
Answer: D
Explanation:
89
90
During routine maintenance, GigabitEthernet1/0/1 on DSW1 was shut down. All other interfaces
were up. DSW2 became the active HSRP device for VLAN 101 as desired. However, after
GigabitEthemet1/0/1 on DSW1 was reactivated, DSW1 did not become the active router for VLAN
101 as desired. What needs to be done to make the group for VLAN 101 function properly?
A. Enable preempt in the VLAN 101 HSRP group on DSW1.
B. Disable preempt in the VLAN 101 HSRP group on DSW2's.
C. In the VLAN 101 HSRP group on DSW1, decrease the priority value to avaluethatis less ' than
the priority value configured in the VLAN 101 HSRP group on DSW2.
D. Decrease the decrement value in the track command for the VLAN 101 HSRP group on U
DSWTs to a values less than the value in the track command for the VLAN 101 HSRP group on
DSW2.
Answer: A
Explanation:
91
92
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface
on DSW1. All other interfaces were up. During this time, DSW1 remained the active device for the
VLAN 102 HSRP group. You have determined that there is an issue with the decrement value in
the track command for the VLAN 102 HSRP group. What needs to be done to make the group
function properly?
A. The decrement value on DSW1 should be greaterthan 5 and less than 15. 0
B. The decrement value on DSW1 should be greaterthan 9 and less than 15.
C. The decrement value on DSW1 should be greaterthan 11 and less than 19.
D. The decrement value on DSWTs should be greaterthan 190 and less than 200.
E. The decrement value on DSWTs should be greaterthan 195 and less than 205.
Answer: C
Explanation:
93
94
All interfaces are active. DSW2 has not become the active device for the VLAN 103 HSRP group.
As related to the VLAN 103 HSRP group, what can be done to make the group function properly?
A. On DSW1, disable preempt.
B. On DSW1, decrease the priority value to a value less than 190 and greater than 150.
C. On DSW2, increase the priority value to a value greater 200 and less than 250.
D. On DSW2, increase the decrement value in the track command to a value greater than 10 and
less than 50.
Answer: C
Explanation:
95
96
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface
on DSW1 and DSW2. All other interfaces were up. During this time, DSW1 became the active
router for the VLAN 104HSRP group. As related to the VLAN 104HSRP group, what can to be
done to make the group function properly?
A. On DSW1, disable preempt.
B. On DSW2 decrease the priority value to a value less than 150.
C. On DSW1, increase the decrement value in the track command to a value greater than 6.
D. On DSW1, decrease the decrement value in the track command to a value less than 1.
Answer: C
Explanation:
97
98
What is the priority value of the VLAN 105 HSRP group on DSW2?
A. 50
B. 100
C. 150
D. 200
Answer: B
Explanation:
99
100
If GigabitEthemet1/0/1 on DSW2 is shutdown, what will be the resulting priority value of the VLAN
105 HSRP group on router DSW2?
A. 90
B. 100
C. 150
D. 200
Answer: A
Explanation:
101
102
What percentage of the outgoing traffic from the 172.16.10.0/24 subnet is being forwarded through
R1?
A. R1-0%
B. R1-50 %, R2-50%
C. R2-100%
D. R1-100%
Answer: D
Explanation:
103
104
Refer to the exhibit. If router R1 interface Etherne0/0 goes down and recovers, which of the
statement regarding HSRP priority is true?
A. The interface will have the priority decremented by 40 for HSRP group 1.
B. The interface will have the priority decremented by 60 for HSRP group 1
C. The interface will have its current priority incremented by 40 for HSRP group 1
D. The interface will have its current priority incremented by 60 for HSRP group 1
E. The interface will default to the a priority of 100 for HSRP group 1
Answer: C
Explanation:
105
106
What issue is causing Router R1 and R2 to both be displayed as the HSRP active router for group
2?
A. The HSRP group number mismatch
B. The HSRP group authentication is misconfigured
C. The HSRP Hello packets are blocked
D. The HSRP timers mismatch
E. The HSRP group priorities are different
Answer: B
Explanation:
107
108
109
110
111
112