Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Pec 5

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

1.

For service entrance conductors, the minimum size of copper wires the code allows is
_______.
a. 3.5 mm2
b. 5.5 mm2
c. 8.0 mm2
d. 14 mm2
2. The maximum number of disconnects the code allows per service grouped in any one
location is _____.
a. 4
b. 6
c. 8
d. 10
3. In general, switches shall be so wired that all switching is done in the ________ conductor.
a. grounded
b. ungrounded c. both a and b d. neither a nor b
4. When circuit breaker are installed in enclosed switchboards, they are usually derated to a
certain percentage. What is this percentage?
a. 60%
b. 80%
c. 50%
d. 70%
5. Which of the following requires a moisture seal at all points of termination?
a. underplaster extensions
b. bare conductor feeders
c. liquidtight flexible metal conduit
d. mineral-insulated cable
6. For a feeder supplying household cooking equipment and electric clothes dryers the
maximum unbalanced load on the neutral conductor shall be considered as ______ of the
load on the ungrounded conductors.
a. 40%
b. 50%
c. 70%
d. 80%
7. A _______ is a protective device for limiting surge voltages by discharging or bypassing
surge current, and it also prevents continued flow of follow current while remaining capable of
repeating these functions.
a. surge arrester
b. auto fuse
c. fuse
d. circuit breaker
8. No swimming pool lighting fixtures shall be installed for operation on supply circuits over
_______ volts between conductors.
a. 24
b. 50
c. 120
d. 150
9. Service conductors between the street main and the first point of connection to the service
entrance run underground is known as the service ________.
a. drop
b. loop
c. lateral
d. cable
10. EMT installed in a wet location, shall have it s coupling and connectors ________.
a. protected against corrosion
b. corrosion resistant
c. raintight type
d. none of these
11. Dual-voltage motors that have a different locked-rotor kva per horsepower on the two
voltages shall be marked with the code letter for the voltage giving the ______ locked-rotor
kva per horsepower.
a. highest
b. average
c. lowest
d. normal
12. Conductor A.W.G. numbers vary _______ to the ampacity.
a. inversely
b. proportionally
c. directly
13. Type TC power and control cable may be used _________.
a. in outdoor locations when supported by a messenger cable
b. as open cable on brackets
c. where exposed by physical damage
d. none of these

d. bi-laterally

14. Raceways on the outside of buildings shall be ______.


a. watertight and arranged to drain
b. weatherproof and covered
c. raintight and arranged to drain
d. rainproof and guarded
15. Receptacles mounted on ______ need not be grounded.
a. outdoor circuits b. garage walls
c. portable generators

d. electric ranges

16. Which of the following may not be used in damp or wet locations?
a. AC armored cable
b. EMT
c. open wiring

d. rigid steel conduit

17. The ampacity of a 125 mm2 IGS cable is ________ amperes.


a. 119
b. 168
c. 215

d. 255

18. Which of the following is the maximum allowable rating of a permanently connected
appliance where the branch overcurrent device is used as the appliance disconnecting
means?
a. 1/8 hp
b. hp
c. hp
d. 1 hp
19. Elevator traveling cables for operating ________ circuits shall contain nonmetallic fillers as
necessary to maintain concentricity.
I. signal
II. control
a. I only
b. II only
c. both I and II d. neither I nor II
20. How would you seal unused kos in panels and boxes?
a. cardboard
b. duct seal
c. tape
d. metal plugs and plates
21. Liquidtight flexible conduit shall not be permitted ______.
a. in hazardous locations
b. in high temperature areas
c. in exposed and concealed work
d. where installations requires flexibility or protection from liquids, vapors or solids
22. Hoistway is a ________ in which an elevator or dumbwaiter is designed to operate.
a. shaftway
b. hatchway
c. well hole
d. all of these
23. Where devices containing disconnecting means are mounted out of reach, suitable means
shall be provided to operate the disconnecting means from the floor. Which of the following
is permitted?
a. devices cannot be mounted out of reach
b. sticks (hook)
c. ladders
d. no method is permitted
24. ________ is defined as properly localizing a fault condition to restrict outages to the
equipment affected, accomplishing by choice of selective fault protective devices.
a. monitoring
b. coordination
c. choice selection
d. fault device
25. Conductors for festoon lighting shall be of the _____ type.
I. thermoplastic
II. rubber covered
III. shielded
a. I only
b. I or II only
c. II or III only

d. I, II, or III

26. A receptacle outlet installed outdoors shall be located so that ______ is not likely to touch the
outlet cover or plate.
a. persons
b. water accumulation
c. metal
d. none of these

27. Metal enclosures to protect _______ from physical damages shall not be required to be
grounded.
a. service conductors
b. feeders
c. cable assemblies
d. none of these
28. ______ switches shall be used for capacitor switching.
a. Isolation
b. Group-operated
c. Shunt
d. High-voltage
29. The secondary circuits of wound-rotor AC motors, including conductors, controllers, resistors,
etc. shall be considered as protected against overload by the _______.
a. disconnect
b. controller
c. breaker
d. motor-overload device
30. Branch circuit conductors supplying a single motor shall have an ampacity not less than
______ percent of the motor full-load current rating.
a. 80
b. 100
c. 115
d. 125
31. Conductors supplying two or more motors shall have an ampacity equal to the sum of the fullload current rating of all the motors plus _____ percent of the highest rated motor in the
group.
a. 15
b. 25
c. 40
d. 50
32. ______ plugs driven into holes in masonry, concrete, plaster, or similar materials shall not be
used.
a. metal
b. plastic
c. leather
d. wooden
33. Where conductors are adjusted to compensate for voltage drop, equipment grounding
conductors, where required, shall be adjusted proportionally according to __________.
a. diameter
b. cross section area
c. circular mil area
d. circumference
34. Service entrance cables, where subject to physical damages, shall be protected in which of
the following?
I. EMT
II. IMC
III. rigid metal conduit
a. III only
b. II and III
c. I, II and III
d. I and III
35. Operation at loads, and intervals of time, both of which may be subject to wide variation is the
definitions of ______.
a. varying duty
b. demand factor
c. cycle
d. periodic duty
36. Underground cable installed under a building shall be in a ______ that is extended beyond
the outside walls of the building.
a. sleeve
b. duct bank
c. gutter
d. raceway
37. A unit of an electrical system which is intended to carry but not utilize electric energy would
be a _____.
I. light bulb
II. snap switch
III. device
IV. receptacle
a. I only
b. III only
c. I, II and IV
d. II, III, and IV
38. _________ boxes shall not be used where conduits or connectors requiring the use of
locknuts or bushings are to be connected to the side of the box.
a. round
b. shallow
c. device
d. gang

39. Lampholders installed over highly combustible material shall be of the ______ type.
a. porcelain
b. low smoke
c. switched
d. unswitched
40. When an outlet is removed from a cellular metal floor raceway, the sections of circuit
conductors supplying the outlet shall be ______.
a. taped
b. dead-ended
c. shorted together
d. removed from the raceway
41. Circuits used only for the operation of fire alarm, other protective signaling systems, or the
supply to fire pump equipment _________to be connected on the supply side of the service
overcurrent device where separately provided with overcurrent protection
a. shall be permitted
b. shall not be permitted
c. not stated in the code
d. not required by the Code
42. Class III locations are those that are hazardous because of ________.
a. the presence of combustible dust
b. over 2500 mm depth of water
c. flammable gases or vapors may be present in the air
d. the presence of easily ignitible fibers or flyings
43. The maximum number of quarter bends in one run of EMT is ________.
a. two
b. four
c. five
d. none of these
44. Which of the following electrical conductor has the highest resistance
a. 3.5 mm2
b. 8.0 mm2
c. 2.0 mm2

d. 5.5 mm2

45. In the schedule of loads for motor circuits, which of the following is NOT included?
a. Type of motor
b. Motor as numbered or identified in the power layout
c. Motors manufacturer
d. Number of phase
46. What is the allowable ampacity of THW insulated copper conductor with an area of 8.0 mm2
and exposed to an ambient temperature of 30oC?
a. 45 A
b. 20 A
c. 30 A
d. 60 A
47. If the project is extensive and requires more time for checking and for computations of fees,
the issuance of the electrical permit need not be issued immediately. However, the delay
shall not be longer than how many working days?
a. 7
b. 6
c. 5
d. 8
48. Location which are hazardous because of the presence of combustible dust.
a. Class I
b. Class II
c. Class III
d. Class IV
49. Operation at substantially constant load for an indefinitely long time.
a. periodic duty
b. intermittent duty
c. . continuous duty
d. short time duty
50. The minimum insulation level for the neutral conductors of solidly grounded systems shall be
______ .
a. 600 V
b. 300 V
c. . 500 V
d. 1,000 V

You might also like