339 0047 0001

Milton Roy
mRoy A & B
METERING
PUMP
INSTALLATION,
OPERATION, AND
MAINTENANCE
MANUAL
Please record the following data for file reference

Tag Number(s):
Model Number:
Serial Number:
Installation Date:
Installation Location:
339-0047-000
ISSUED 08/09
PRECAUTIONS
The following precautions should be taken when working with metering pumps.
Please read this section carefully prior to installation.
Protective Clothing
ALWAYS wear protective clothing, face shield, safety glasses and gloves when working on or near your
metering pump. Additional precautions should be taken depending on the solution being pumped. Refer
to Material Safety Data Sheets for the solution being pumped.
Hearing Protection
It is recommended that hearing protection be used if the pump is in an environment where the timeweighted average sound level (TWA) of 85 decibels is exceeded. (as measured on the A scale -- slow
response)
Electrical Safety
Remove power and ensure that it remains off while maintaining pump.
DO NOT FORGET TO CONNECT THE PUMP TO EARTH
Electric protection of the motor (Thermal protection or by means of fuses) is to correspond to
the rated current indicated on the motor data plate.
Liquid Compatibility
Verify if the materials of construction of the wetted components of your pump are recommended for the
solution (chemical) to be pumped.
Pumps Water Primed
All pumps are tested with water at the factory. If your process solution is not compatible with water, flush
the Pump Head Assembly with an appropriate solution before introducing the process solution
Plumbing and Electrical Connections
Always adhere to your local plumbing and electrical codes.
Line Depressurization
To reduce the risk of chemical contact during disassembly or maintenance, the suction and discharge
lines should be depressurized before servicing.
Over Pressure Protection
To ensure safe operation of the system it is recommended that some type of safety/pressure-relief valve
be installed to protect the piping and other system components from damage due to over-pressure.
Lifting
This manual should be used as a guide only - Follow your companys recommended lifting procedures. It
is not intended to replace or take precedence over recommendations, policies and procedures judged as
safe due to the local environment than what is contained herein.
Use lifting equipment that is rated for the weight of the equipment to be lifted.
TABLE OF CONTENTS
SECTION 1 - GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 PUMP CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 PUMP PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.5 PRINCIPLE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.6 GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SECTION 2 - INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1 UNPACKING/INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.3 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 PUMP MOUNTING/LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.5 OUTDOOR INSTALLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6 FLANGE MOUNTED MOTORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8 MOTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.9 PUMP LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.10 PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.11 BACK PRESSURE SPRING INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.12 OPERATION WITH SUCTION LIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SECTION 3 - OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.1 INITIAL START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.2 RESETTING THE RELIEF VALVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3.3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
SECTION 4 - MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 RPM KIT COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3 RETURNING UNITS TO THE FACTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4 ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5 SEMI ANNUAL OIL CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6 CHECK VALVE CARTRIDGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.7 DIAPHRAGM(S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.8 RELIEF VALVE POPPET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.9 CORRECTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.9.1 Check Valve Cartridge Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.9.1.1 Metallic Liquid Ends (Figures 20, 21, 22 & 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.9.1.2 mRoy A Plastic Liquid End, Current Design (Figure 20). . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.9.1.3 mRoy B Plastic Liquid End (Figure 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.9.2 Relief Valve Poppet Replacement (Figure 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.9.3 Diaphragm Replacement (Figures 20-27) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.9.4 Motor and Worm Replacement (Figures 18 & 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.9.5 Control Spool O-Rings Replacement (Figure 18, 20, & 21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.9.6 Worm Gear Replacement (Figure 18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.9.7 Connecting Rod and Plunger Replacement (Figure 18). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SECTION 5 - TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SECTION 5 - PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.2 ILLUSTRATED PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.3 BASIC PARTS LIST FOR DRIVE MODELS RA, RH, RT RJ, AND RP (FIGURES 18 & 19). . . . 41
6.4 PARTS COMMON TO LIQUID END MODELS RA, RP, AND RJ (FIGURES 20 & 21) . . . . . . . . . . . 43
6.5 DIAPHRAGM HEAD DESIGN- 6 BOLT (5" WITH HOLES) LIQUID END MODEL RA (FIGURE 21) . . 43
6.6 DIAPHRAGM HEAD DESIGN- 8 BOLT (2-7/8") LIQUID END MODEL RH & RT (FIGURE 21) . . . . . 44
6.7 DIAPHRAGM HEAD DESIGN- 8 BOLT (4") LIQUID END MODEL RJ (FIGURE 21) . . . . . . . . . . . . . . 45
6.8 MODEL RP SUCTION CHECK VALVE PARTS (FIGURE 20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.9 MODEL RA12 PLASTIC LIQUID END PARTS (FIGURE 20 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.10 MROY RA MOTOR MOUNT PARTS (FIGURES 18 & 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.11 ELECTRONIC CAPACITY CONTROL MOUNTING (FIGURE 24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.12 PNEUMATIC CAPACITY CONTROL (3-15 PSI DIRECT) (FIGURE 24) . . . . . . . . . . . . . . . . . . . . . . . . 50
6.13 SIMPLEX LEAK DETECTION PARTS, FIGURE 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.14 DOUBLE DIAPHRAM PARTS (FIGURE 23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.15 BASIC PARTS LIST FOR DRIVE MODELS RB (RS, RM, RB) (FIGURES 18 & 19) . . . . . . . . . . 57
6.16 LIQUID END RB & RM (FIGURE 25). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.17 LIQUID END RS (FIGURE 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
ii
6.18 MODEL RB12 & RM12 PLASTIC LIQUID END PARTS (FIGURE 25) . . . . . . . . . . . . . . . . . . . . . . 60
6.19 MROY RB MOTOR MOUNTS (FIGURES 18 & 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.20 ELECTRONIC CAPACITY CONTROL MOUNTING (FIGURE 24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.21 SIMPLEX LEAK DETECTOR PARTS- GAUGE & NEMA SWITCH (FIGURE 26) . . . . . . . . . . . . . . . . 63
6.22 DOUBLE DIAPHRAGM PARTS FOR METALIC LIQUID END (FIGURE 27) . . . . . . . . . . . . . . . . . . . . 65
6.23 DOUBLE DIAPHRAGM PARTS- WITH CONDUCTIVITY PROBE FOR PLASTIC LIQUID END (RM &
RB) (FIGURE 27) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
APPENDIX A - MODEL CODE HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
LIST OF ILLUSTRATIONS
FIGURE 1.
Pump Operation With By-Pass Port Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FIGURE 2.
Pump Operation With By-Pass Port Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FIGURE 3.
mRoy Data Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
FIGURE 4.
mRoy A, H, J, and P Model Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
FIGURE 5.
mRoy A, H, J, and P Gear/Motor Mount/Connection/Capacity Control; Select Mode Code. . . . . . . .5
FIGURE 6.
mRoy A, H, J, and P Type of Liquid End; Select Mode Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
FIGURE 7.
mRoy A, H, J, L, and P Routine Maintenance Kit List, By Model Code . . . . . . . . . . . . . . . . . . . . . . .6
FIGURE 8.
mRoy A Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
FIGURE 8A. mRoy RT, RH, & RJ Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

FIGURE 9.
mRoy P Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
FIGURE 10. mRoy B Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

FIGURE 11. mRoy Pump (All Models) Capacity Derating Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
FIGURE 12. mRoy B Model Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
FIGURE 13. mRoy B Routine Maintenance Kit List, By Model Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FIGURE 14. Mounting Bolt Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
FIGURE 15. Back Pressure Spring Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
FIGURE 16. Typical Piping System Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
FIGURE 17. Diaphragm Head Bolt Torque Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
FIGURE 18. Common Parts - mRoy A & B Side View and API Motor Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
FIGURE 19. Common Parts - mRoy A & B End View and mRoy A Close Coupled Motor Mount . . . . . . . . . . . .35
FIGURE 20. mRoy A Metallic and Plastic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
FIGURE 20. mRoy A Metallic Low Pressure and High Pressure Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
FIGURE 20. mRoy A Bar Stock Liquid End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
FIGURE 23. mRoy A Double Diaphragm and Leak Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
FIGURE 24. mRoy A and B Actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
FIGURE 25. mRoy B Metallic and Plastic Liquid End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
FIGURE 26. mRoy B Leak Detection With Switch and Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
FIGURE 27. mRoy B Double Diaphragm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
iii
THIS PAGE INTENTIONALLY BLANK
iv
SECTION 1
GENERAL DESCRIPTION
1.1 INTRODUCTION
1.3
The mRoy pump is a highly reliable controlled volume

pump of hydraulically actuated diaphragm design. The
family of mRoy A and B frame pumps are further
broken down into Model Codes. For ease of discussion, this manual will refer to either frame size as mRoy
A and mRoy B rather than the specific Model Code (RA
or RS). The new product codes for the mRoy A are
given in Figures 4 through 6. The product codes for the
mRoy B are shown in Figure 12.
For a general description of the mRoy pump you have

purchased, compare the model number and product
code printed on the pumps data plate (shown in Figure
3) to the appropriate model number and product code
shown in Figures 4 through 6 and Figure 12.
1.4
PUMP PERFORMANCE
The charts in Figures 8 through 10 show the performance ranges for all mRoy A & B frame pumps. If
appropriate, refer also to the derating table shown in
Figure 11.
Historical Model Codes are found in Appendix A.

1.2
PUMP CHARACTERISTICS
GENERAL INFORMATION
1.5
Pump capacity is adjustable while the pump is running

or stopped. Capacity adjustment can be made manually or automatically by a signal from remote control
instruments.
PRINCIPLE OF OPERATION
Pumping action is developed and controlled by four

basic components as follows (Figures 1 & 2):
1. The pump plunger A reciprocates with a
constant stroke length and displaces oil into and
out of the diaphragm chamber C.
Repetitive accuracy of the metered discharge volume

is maintained within a l% range at constant conditions
of pressure, temperature and pump capacity adjustment setting.
2. The flexible diaphragm X is a movable partition

between the plunger oil and fluid being pumped.
The mRoy pump is a reliable, compact, controlled volume diaphragm pump for normal corrosive or toxic
chemicals and light slurries with viscosities up to 200
S.S.U. (40 cps). For higher viscosities, the mRoy P
series pump is available (to 12,200 cps).
3. An oil bypass circuit from the diaphragm

chamber C to the reservoir D through
passage E bypass port H and control spool
(valve) F.
4. A bypass control plunger G which moves with
and is directly coupled to the pump plunger to
correlate bypass shut off at port H to pump
plunger position.
A plunger, reciprocating at a fixed stroke, displaces a

fixed volume of hydraulic fluid, which actuates a flexible, chemically inert PTFE diaphragm to create pumping action. Double ball check valves are used on the
suction and discharge to insure consistent metering
accuracy. Capacity control is established by adjusting
the volume of hydraulic fluid, which bypasses the diaphragm cavity.
In operation, as the pump plunger and bypass control

plunger move forward as shown in Figure 1, the displaced oil is bypassed to the oil reservoir until the control plunger G closes the bypass port H as shown in
Figure 2. Then the balance of the plunger displacement
is imposed on the flexible diaphragm that moves and
displaces the fluid being pumped through the discharge ball checks.
Metering with repetitive accuracy is possible only if the

volume of the hydraulic oil in the displacement chamber is maintained constant for each stroke. This is
accomplished by mechanically opening the displacement chamber to the oil reservoir for a short period at
the end of every suction stroke and the beginning of
each pressure stroke. During this period air or vapor is
bled from the system, lost oil is replenished, and allowances are made for the expansion or contraction of the
oil due to temperature change. For more information,
refer to Principle of Operation.
On the suction stroke, the pump plunger pulls oil out of

the diaphragm cavity, which moves the flexible diaphragm and pulls fluid through the suction ball checks.
When the control plunger G opens the bypass port
H the balance of the plunger oil displacement can be
supplied from the reservoir through the bypass passages.
The discharge capacity is adjusted from 0100% by

rotating the adjustment knob that moves the control
spool (valve) F so that the bypass port H is closed at
the desired percentage of the total plunger stroke.
When the control spool (valve) is adjusted to 100%
capacity the bypass port will be positioned so that it is
opened at the very end of the suction stroke. Then on
the pressure stroke, the bypass port is immediately
closed so the entire plunger displacement is imposed
upon the flexible diaphragm.
opened when the plungers have completed one-half of

the suction stroke. On the next pressure stroke, the oil
displaced by the pump plunger will be bypassed
through the open port to the reservoir for the first 50%
of the stroke before the by-pass port is closed by the
control plunger. The remaining 50% of the plunger displacement will then be imposed on the flexible diaphragm so that fluid is discharged for only 50% of the
plunger travel. A similar analysis would apply for 0%
capacity setting on the control spool (valve) where all
the plunger oil displacement is bypassed to the reservoir.
With the control spool (valve) adjusted for 50% capacity the bypass port will be positioned so that it is
Figure 1. Pump Operation With By-Pass Port Open
Figure 2. Pump Operation With By-Pass Port Closed

2
1.6
GENERAL SPECIFICATIONS
Accuracy
1% steady state accuracy over 10:1 turndown
Drive
Hydraulic bypass design allows adjustment from
0 to 100% of rated capacity while stopped or
running
Liquid End
High performance check valves
Diaphragm
Hydraulically actuated diaphragm provides extra
long diaphragm life
Relief Valve
Adjustable internal relief valve
Capacity Control
Micrometer ..........................................standard
Electronic ................420 mA (except L series)
Pneumatic ................315 psi (except L series)
Figure 3. mRoy Data Plate
Stroke Length
Models RA, RH, RT, RJ, RP ...... 0.7 (1.78 cm)
Models RB, RM, RS ................... 1.5 (3.81 cm)
MODEL CODE SELECTION

END ITEM AND OPTION SELECT NUMBER
mROY A SERIES
Option Select Number
End item Model Code
1*
Material
Plunger
Gear
Mount /
Code
Diameter
Set
Motor
Suction
Discharge
Connection
Capacity
Rupture
Control
Detection
& Base
* 2 for Duplex
mRoy A LIQUID END MATERIAL CODE SELECTION
Description
Code
Cast Iron
0
316 SS (STANDARD)
1
2
PVC (N/A with 9.5:1 Gear Ratio)
PVDF (N/A with 9.5:1 Gear Ratio)
7
Alloy 20
5
Alloy C22
6
mRoy A PLUNGER DIAMETER
Description
Code
07
7/16" Diameter
5/8" Diameter
10
1-1/16" Diameter
17
mROY H/T SERIES

End Item Model Code
RH=7/16 Dia. Plunger

RT= 3/8 Dia. Plunger
Gear
Set
Material
Code
mRoy H LIQUID END

Code
0
1
5
Mount /
Motor
Suction
Connection
Discharge Capacity
Connection Control
Base
MATERIAL
Description
Cast Iron
316 SS (STANDARD)
Alloy 20
mRoy J SERIES
End Item Model Code
Gear
Set
Material
Code
Mount /
Motor
Suction
Connection
Discharge Capacity
Connection Control
Rupture
Detection
& Base
mRoy J LIQUID END MATERIAL

Description
Code
316 SS (STANDARD)
1
5
Alloy 20
mRoy P SERIES
End item Model Code
Material
Code
Plunger
Diameter
Gear
Set
Mount /
Motor
Suction
Connection
mRoy P LIQUID END MATERIAL

Code
Description
Cast Iron
0
316 SS (STANDARD)
1
5
Alloy 20
mRoy P PLUNGER DIAMETER
Code
Description
7/16" Diameter
07
5/8" Diameter
10
1-1/16" Diameter
17
Figure 4. mRoy A, H, T, J, and P Model Code
Discharge Capacity
Connection Control
Rupture
Detection
& Base
GEAR SET (ALL mRoy A FRAME)

Code
77
48
24
15
10
Description
77:1 Gear Ratio
48:1 Gear Ratio
24:1 Gear Ratio
15:1 Gear Ratio
9.5:1 Gear Ratio
N/A for RJ or RP
N/A for RJ or RP
1725 rpm
23 spm
37 spm
73 spm
117 spm
185 spm
1425 rpm
19 spm
30 spm
60 spm
96 spm
152 spm
1140 rpm
15 spm
24 spm
47 spm
76 spm
120 spm
MOTORS and MOUNTS

STANDARD MOTOR with Close Coupled flange
Code
Description
Does not require motor
A1
1/4 HP Motor, TE, 1725 RPM, 1 Phase, 60 Hertz, 115 Volt & Close Coupled Flange
mount from below
A8
1/4 HP Motor, TE, 1725 RPM, 3 Phase, 60 Hertz, 230/460 Volt & Close Coupled Flange
Note: These motors replace the obsolete integral motor offering. They are standard
NEMA 56 C frame motor on a short flange.
MOTOR MOUNTS (Use only when motor is ordered from Milton Roy
1/4 HP minimum.
Code
SR
SS
Motor supplied by Milton
FR
Roy from Accessory
F4
Section
FS
MD
MOTOR MOUNTS
Description
Close Coupled Flange, NEMA 56C (STANDARD)
Close Coupled Flange, IEC Frame 71, B5 Flange
API Flange Mount, NEMA 56C
API Flange Mount, NEMA 143TC/145TC
API Flange Mount, IEC Frame 71, B5 Flange
NOTE: Must be used when pump is not ordered with motor
1/4 HP minimum.
Code
1X
2X
3X
Motor supplied by others
4X
5X
6X
Description
Close Coupled Flange, NEMA 56C
Close Coupled Flange, IEC Frame 71, B5 Flange
SUCTION CONNECTION
Metallic Liquid Ends
Code
SE
T1
T3
S1
S3
Description
NPT 1/2" Female (STANDARD)
ANSI 150# RF 1/2" Threaded
ANSI 150# RF 1/2" Socket Welded
Code
SE
T1
Description
NPT 1/2" Male (STANDARD)
150# 1/2" Thd flange
PVC
316 SS
Alloy 20
N/A
N/A
N/A
N/A
N/A
Standard
Standard
Standard
N/A
N/A
N/A
N/A
Plastic Liquid Ends
Notes:
1. Base option recommended with flanged connections.
2. Flanges can only be welded at flanged end
DISCHARGE CONNECTION
Codes and prices are the same as Suction Connection.
Discharge connection size for SE code on metallic liquid ends is 1/4" NPT.
CAPACITY CONTROL
Code
M2
M1
ML
E1
E2
EA
EB
EE
PN
Description
Manual Micrometer Knob - PVC(STANDARD)
Manual Micrometer Knob - 316 SS
Locking Manual Micrometer Knob - 316 SS
Electronic - NEMA 4, 4-20 mA, 115 Volt
Electronic - Explosion Proof, 4-20 mA, 115 Volt
Mount for Electronic, Less Actuator
Pneumatic, 3-15 psi, Direct Acting
Figure 5. mRoy A, H, T, J, and P Gear/Motor Mount/Connection/Capacity Control; Select Mode Code
RUPTURE DETECTION & BASE (mRoy A FRAME)

Code
Description
NN
None (STANDARD)
NB
Base Only - Recommended with Flanges
C5
Rupture Detection with Base & Gauge
N/A on RH/RT
SN
Rupt. Detect. w/ Base, Gauge, & NEMA 4 Switch
N/A on RH/RT
S7
Rupt. Detect. w/ Base, Gauge, & Ex. Prf Switch
N/A on RH/RT
DD
Double Diaphragm with Base
N/A on RH/RT or RJ
DP
Double Diaphragm with Base & Conductivity Probe

Relay supplied separately - see accessory pricing
Plastic Liquid Ends

Code
Description
NB
Base Only (STANDARD)
DD
Double Diaphragm with Base
DP
Double Diaphragm with Base & Conductivity Probe

Figure 6. mRoy A, H, T, J, and P Type of Liquid End; Select Mode Code
ROUTINE MAINTENANCE KITS mRoy A

MRoy RPM kits for pumps noted above
Model
MRoy A, H, T, J
Liquid End Material
Kit Number
316 SS & Cast Iron
RPM002
Alloy 20
RPM005
PVC w/NPT connections
RPM007
PVC w/tubing connections
RPM003
PVDF w/NPT connections
RPM008
PVDF w/tubing connections
RPM004
Alloy C22
RPM006
RA11 w/Peek Diaph., 5 inch
RPM087
Hast B
RPM093
Diaph Teflon, 3.98 inch

MRoy P
RPM0013037
316 ss & Cast Iron
RPM009
Alloy 20
RPM010
Figure 7. mRoy A, H, T, J, and P Routine Maintenance Kit List, By Model Code

6
MODEL RA CAPACITY/PRESSURE TABLE

Plgr.
Dia.
Gear
Code
SPM 60 hz
(50 hz)
Metallic
100 PSI
150 PSI
Plastic
200 PSI
300 PSI
23
Use H Series
(19)
7/16
48
37
0.8
0.7
0.7
(30)
(0.66)
(0.58)
(0.58)
24
73
1.7
1.7
1.7
(60)
(1.41)
(1.41)
(1.41)
15
117
2.8
2.7
2.7
(96)
(2.32)
(2.24)
(2.24)
48
37
1.8
1.7
1.7
5/8
(30)
(1.49)
(1.41)
(1.41)
24
73
3.8
3.7
3.7
(60)
(3.15)
(3.07
(3.07
15
117
6.2
6.1
6.0
(96)
(5.15)
(5.06)
(4.98)
48
37
6.1
6.0
5.9
(30)
(5.06)
(4.98)
(4.90)
1-1/16
24
73
12.3
12.2
12.1
(60)
(10.21)
(10.13)
(10.04)
15
117
19.4
19.4
19.2
(96)
(16.10)
(16.10)
(15.9)
10
185
30.0
29.5
29.0
(152
(24.90)
(24.48)
(24.07)
NOTES: Refer to notes shown in Figure 10, mRoy B Capacity/Pressure Table.
350 PSI
100 PSI
150 PSI
0.7
(0.58)
1.6
(1.33)
2.6
(2.16)
1.6
(1.33)
3.5
(2.90)
5.7
(4.73)
5.5
(4.57)
11.2
(9.30)
18.1
(15.02)
---
0.48
(0.40)
0.65
(0.54)
1.5
(1.25)
2.5
(2.08)
1.6
(1.33)
3.5
(2.90)
5.6
(4.65)
5.7
(4.73)
11.3
(9.38)
18.1
(15.02)
---
0.46
(0.38)
0.62
(0.51)
1.5
(1.25)
2.4
(1.99)
1.5
(1.25)
3.4
(2.82)
5.5
(4.57)
5.6
(4.65)
11.2
(9.30)
18.0
(14.94)
---
77
0.7
(0.58)
1.6
(1.33)
2.7
(2.24)
1.6
(1.33)
3.6
(2.99)
5.9
(4.90)
5.7
(4.73)
11.5
(9.55)
18.5
(15.35)
---
Figure 8. mRoy A Capacity/Pressure Table (capacities shown in GPH)
MODEL RT, RH, & RJ CAPACITY/PRESSURE TABLE

Plgr.
Dia.
Gear
Code
SPM 60 hz
(50 hz)
Metallic Only
100 PSI
500 PSI
700 PSI
77
23
0.46
0.41
0.37
(19)
(0.38)
(0.34)
(0.31)
48
37
0.73
0.66
0.6
mRoy T
(30)
(0.61)
(0.55)
(0.50)
3/8
24
73
1.45
1.31
1.18
(60)
(1.21)
(1.09)
(0.98)
15
117
2.32
2.10
1.9
(96)
(1.93)
(1.75)
(1.58)
10
185
3.67
3.32
3
(152)
(3.06)
(2.77)
(2.5)
77
23
0.57
0.54
0.5
(19)
(0.47)
(0.45)
(4.2)
mRoy H
48
37
0.8
0.7
0.6
7/16
(30)
(0.66)
(0.58)
(0.5)
24
73
1.7
1.6
1.5
(60)
(1.41)
(1.33)
(1.25)
15
117
2.8
2.6
2.5
(96)
(2.32)
(2.17)
(2.08)
10
185
4.4
4.1
4.0
(152)
(3.65)
(3.42)
(3.33)
48
37
1.8
1.5
1.4
(30)
(1.5)
(1.25)
(1.17)
mRoy J
24
73
3.8
3.4
3.2
5/8
(60)
(3.17)
(2.83)
(2.67)
15
117
6.2
5.6
5.3
(96)
(5.17)
(4.67)
(4.42)
NOTES: Refer to notes shown in Figure 10, mRoy B Capacity/Pressure Table
925 PSI
1500 PSI
1800 PSI
2000 PSI
0.35
(0.29)
0.56
(0.47)
1.11
(0.92)
1.78
(1.48)
2.81
(2.34)
0.5
(4.2)
0.6
(0.5)
1.5
(1.25)
2.4
(2.0)
3.8
(3.17)
--3.1
(2.59)
5.1
(4.25)
0.28
(0.23)
0.45
(0.38)
0.89
(0.74)
1.43
(1.19)
2.26
(1.88)
0.43
(0.36)
0.6
(0.5)
1.3
(1.08)
2.1
(1.74)
3.3
(2.74)
0.24
(0.20)
0.38
(0.34)
0.75
(0.62)
1.2
(1.00)
2
(1.7)
0.4
(0.33)
0.6
(0.5)
1.2
(1.0)
2
(1.66)
3.1
(2.57)
0.21
(0.18)
0.34
(0.28)
0.68
(0.57)
1.09
(0.91)
1.72
(1.43)
Figure 8A. mRoy RT, RH, & RJ Capacity/Pressure Table (capacities shown in GPH)
MODEL RP CAPACITY/PRESSURE TABLE

Plgr.
Dia.
7/16
Gear
Code
SPM 60 hz
(50 hz)
77
23
(19)
37
(30)
73
(60)
117
(96)
37
(30)
73
(60)
117
(96)
37
(30)
73
(60)
117
(96)
48
24
15
48
5/8
24
15
48
1 1/16
24
15
Metallic Only
100 PSI
150 PSI
200 PSI
300 PSI
350 PSI
0.63
(0.52)
1.4
(1.16)
2.4
(1.99)
1.4
(1.16)
3.2
(2,66)
5.3
(4.40)
5.1
(4.23)
10.2
(8.47)
16.6
(13.78)
0.63
(0.52)
1.4
(1.16)
2.3
(1.91)
1.4
(1.16)
3.1
(2.57)
5.1
(4.23)
4.9
(4.07)
9.9
(8.22)
16.2
13.45)
Max. Fluid Viscosity

(Centipoise)
Not Available
0.72
(0.60)
1.5
(1.25)
2.5
(2.08)
1.6
(1.33)
3.4
(2.82)
5.6
(4.65)
5.5
(4.57)
11.0
(60)
17.5
(14.52)
0.63
(0.52)
1.5
(1.25)
2.4
(1.99)
1.5
(1.25)
3.3
(2.74)
5.5
(4.57)
5.4
(4.48)
10.9
(9.05)
17.4
(14.44)
0.63
(0.52)
1.5
(1.25)
2.4
(1.99)
1.5
(1.25)
3.3
(2.74)
5.4
(4.48)
5.3
(4.40)
10.8
(8.96)
17.3
(14.36)
NOTES: Refer to notes shown in Figure 10, mRoy B Capacity/Pressure Table
Figure 9. mRoy P Capacity/Pressure Table (capacities shown in GPH)
7,500
4,000
2,000
5,000
2,500
1,250
1,000
500
300
MODEL RB, RM, RS CAPACITY PRESSURE TABLE

PVC & Metallic
MODEL SPM
100 PSI
150 PSI
200 PSI
4.7
4.6
48
4.6
(3.90)
(3.82)
(3.82)
RS
(40)
72
(60)
96
(80)
144
(120)
48
(40)
72
(60)
RM
96
(80)
7/8
144
Dia.
(120)
48*
(40)*
RB
72*
1-7/16 (60)*
96**
Dia.
(80)**
144**
(120)**
19/32
Dia.
7.0
(5.81)
9.5
(7.88)
13.3
(11.04)
10.0
(8.30)
16.0
(13.28)
21.0
(17.43)
30.4
(25.23)
27.0
(22.41)
42.0
(34.86)
57.0
(47.31)
85.0
(70.55)
6.9
(5.73)
9.4
(7.80)
13.2
(10.96)
9.7
(7.80)
15.7
(13.03)
20.7
(17.18)
30.1
(24.98)
26.0
(21.58)
41.0
(34.03)
56.0
(46.48)
84.0
(69.72)
400 PSI
4.4
(3.65)
600 PSI
4.2
(3.49)
6.7
(5.56)
8.9
(7.39)
12.8
(10.62)
8.2
(6.81)
14.3
(11.87)
19.3
(16.02)
28.9
(23.99)
21.0
(17.43)
36.0
(29.88)
51.0
(42.33)
79.0
(65.57)
6.5
(5.39)
8.6
(7.14)
12.5
(10.38)
7.0
(5.81)
13.2
(10.96)
18.2
(15.11)
27.9
(23.16)
6.9
(5.73)
9.3
(7.72)
13.1
(10.87)
9.4
(7.80)
15.4
(12.78)
20.4
(16.93)
29.9
(24.82)
25.0
(20.75)
40.0
(33.20)
55.0
(46.65)
83.0
(68.89)
Metallic Only
800 PSI
1000 PSI
4.0
3.8
(3.32)
(3.15)
6.3
(5.23)
8.3
(6.89)
12.3
(10.21)
5.9
(4.90)
12.1
(10.04)
17.1
(14.19
27.0
(22.41)
1200 PSI 1500 PSI

3.6
3.3
(2.99)
(2.74)
6.1
(5.06)
7.9
(6.56)
12.0
(9.96)
4.7
(3.90)
11.0
(9.13)
16.0
(13.28)
25.6
(21.25)
5.9
(4.90)
7.6
(6.31)
11.8
(9.79)
5.6
(4.65)
7.1
(5.89)
11.4
(9.46)
NOTES:
1. Capacities shown are for simplex pumps. Double capacity for duplex pumps.
2. Certain options require that the maximum capacity be derated. Refer to the derating table.
3. Capacities shown are the max. pump capacities in gph, based on 60 hz, 1725 rpm. 50 hz, 1425 max. capacities are
shown in ().
4. Non-shaded ranges require hp 3 phase of hp single phase motors. Shaded Ranges require hp 3 phase or 1
hp single phase motors.
* Duplex 1 7/16 plungers at 96 or 144 SPM are limited to 250 psi.
** Duplex 1 7/16 plungers at 96 or 144 SPM are limited to 250 psi.
PVC is limited to 150 psi. PVC is not available on pumps with a 19/32 plunger
Figure 10. mRoy B Capacity/Pressure Table (capacities shown in GPH)

MROY PUMP FLOW DERATING TABLE
7/16 & 5/8
Plunger Diameter
Series
Electronic or Pneumatic
Capacity Control
Diaphragm Rupture
Detection
Double Diaphragm
3/8
1 1/16
19/32
7/8
1 716
--
0.95
0.95
0.95
0.95
0.90
0.90
1.0
0.90
0.90
--
0.95
--
0.95
0.95
0.95
0.95
0.95
0.95
0.95
0.95
--
0.95
0.95
0.95
0.95
0.95
0.95
NOTES:
Certain options require that the maximum capacity be derated. Multiply capacities in the capacity/pressure tables in Figures 7
through 10 by the appropriate factors in the table above.
Figure 11. mRoy Pump (All Models) Capacity Derating Table

9
mRoy B Series
MODEL CODE SELECTION
End item Model Code

R
1*
Liquid End
Plunger
Diameter
Material
* 2 for Duplex
PLUNGER DIAMETER
Code
S
M
B
LIQUID END MATERIAL
Code
1
2
5
7
GEAR SET
END ITEM AND OPTION SELECT NUMBER

Gear
Set
Motor
Mount
Suction
Connection
Discharge
Connection
Capacity
Control
Rupture
Detection
& Base
Description
19/32" Diameter
7/8" Diameter
1-7/16" Diameter
Description
316 SS (STANDARD)
PVC (not available with plunger code "S")
Alloy 20
PVDF
(Plunger code "B" only)
Code
Description
1725 rpm
1425 rpm
1140 rpm
38
25
19
12
10
38:1 Gear Ratio

25:1 Gear Ratio
19:1 Gear Ratio
12:1 Gear Ratio
9.51 Gear Ratio
48 spm
72 spm
96 spm
144 spm
N/A
40 spm
60 spm
80 spm
120 spm
148 spm
31 spm
48 spm
62 spm
95 spm
N/A
MOTOR MOUNTS
MOTOR MOUNTS (Use only when motor is ordered from Milton Roy - see section 4100)
Refer to Capacity/Pressure table for horsepower required.
Code
Description
FR
F4
Motor supplied by Milton Roy
from Accessory Section
F8
F9
MOTOR MOUNTS
NOTE: Must be used when pump is not ordered with motor (to cover added cost of testing).
Refer to Capacity/Pressure table for horsepower required.

Code
Description
3X
4X
Motor supplied by others
5X
6X
SUCTION CONNECTION
PVC
Plastic Liquid End

Notes:
Code
SE
T1
T3
S1
S3
Description
NPT 1/2" Female (STANDARD)
NPT 1/2" Male (STANDARD)

SE
T1
150# 1/2" Thd flange
1. Base option recommended with flanged connections.
DISCHARGE CONNECTION
N/A
N/A
N/A
N/A
N/A
316 SS
Alloy 20
Standard
Standard
Standard
N/A
N/A
N/A
N/A
2. Flanges can only be welded at flanged end.
Same codes and prices as Suction Connection
NOTE: Connection sizes for SE code metallic are 3/8" NPT on RM & RB series, and 1/4" NPT on RS series.
CAPACITY CONTROL
Code
AL
ML
E1
E2
EA
EB
EE
PN
Description
Manual Micrometer Knob - Aluminum (STANDARD)

Manual Micrometer Locking Knob - 316 SS
Mount for Electronic, Less Actuator
Pneumatic, 3-15 psi, Direct Acting
Remember to
Remember to
Remember to
Remember to
derate
derate
derate
derate
pump
pump
pump
pump
Remember to derate pump
RUPTURE DETECTION & BASE

All Liquid Ends
Metallic Liquid
Ends Only
Plastic Liquid
End Only
Code
NN
NB
Description
None (STANDARD)
Base
Code
C5
SN
S7
Description
Rupture Detection with & Gauge
Rupt. Detect. W/Gauge, & NEMA 4 Switch
Rupt.Detect. W/Gauge, & Exp. Prf Switch
DD
DP
Standard
Double Diaphragm
Double Diaphragm w/Conductivity Probe
Figure 12. mRoy B Model Codes

10

Remember to derate
Remember to derate
ROUTINE MAINTENANCE KITS mRoy B

MRoy RPM kits for pumps noted above
Model
MRoy S
MRoy M & B
Liquid End Material
Kit Number
316 ss
RPM011
Alloy 20
RPM012
RS 11 w/Peek Diaph.
RPM092
316 ss
RPM-0014-021
PVC
RPM-0014-032
Alloy 20
RPM-0014-025
RB Kynar
RPM-0014-037
Figure 13. mRoy B Routine Maintenance Kit List, By Model Code
11
12
SECTION 2
INSTALLATION
2.1 UNPACKING/INSPECTION
as Mobile Oil Corporation product Mobilarma 524. Fill

the compartment completely to minimize air space and
water vapor condensation. After storage, drain this
material and refill the equipment with the recommended lubricant for equipment commissioning.
Units are shipped Ex Works, Ivyland, Pa. and the title

passes to the customer when the carrier signs for
receipt of the unit. In the event that damages occur during shipment, it is the responsibility of the customer to
notify the carrier immediately and to file a damage
claim. Carefully examine the shipping crate upon
receipt from the carrier to be sure there is no obvious
damage to the contents. Open the crate carefully so
accessory items fastened to the inside of the crate will
not be damaged or lost. Examine all material inside the
crate and check against the packing list to be sure that
all items are accounted for and intact.
2.2
2. Brush all unpainted metal surfaces with multipurpose

grease (NLGI grade 2 or 3). Store these unattached.
Electrical Equipment
1. Motors should be prepared in the manner prescribed
by their manufacturer. If information is not available,
dismount and store motors as indicated in step 3
below.
STORAGE
2. Dismount electrical equipment (including motors)

from the pump.
Short Term Storage (Less than 6 Months)

It is preferable to store the material under a shelter in
its original package to protect it from adverse weather
conditions. In condensing atmospheres, follow the long
term storage procedure.
3. For all electrical equipment, place packets of Vapor

Phase Corrosion Inhibitor (VPCI) inside of the enclosure, then place the entire enclosure, with additional
packets, inside a plastic bag. Seal the bag tightly
closed. Contact Milton Roy Service Department for
recommended VPCI materials.
Long Term Storage (Longer than 6 Months)

The primary consideration in storage of pump equipment is to prevent corrosion of external and internal
components. This corrosion is caused by natural circulation of air as temperature of the surroundings change
from day to night, day to day, and from season to season. It is not practical to prevent this circulation which
carries water vapor and other corrosive gasses, so it is
necessary to protect internal and external surfaces
from their effects to the greatest extent possible.
2.3
SAFETY PRECAUTIONS
When installing, operating, and maintaining the mRoy

pump, keep safety considerations foremost. Use
proper tools, protective clothing, and eye protection
when working on the equipment and install the equipment with a view toward ensuring safe operation. Follow the instructions in this manual and take additional
safety measures appropriate to the liquid being
pumped. Be extremely careful in the presence of hazardous substances (e.g., corrosives, toxics, solvents,
acids, caustics, flammables, etc.).
When the instructions given in this section are completed, the equipment is to be stored in a shelter; protected from direct exposure to weather. The prepared
equipment should be covered with a plastic sheet or a
tarpaulin, but in a manner which will allow air circulation
and prevent capture of moisture. Equipment should be
stored 12 inches or more above the ground.
2.4
PUMP MOUNTING/LOCATION
The mRoy pump can be mounted on any surface that

is flat and level for the support feet. Three mounting
bolt holes are provided in the support feet for use when
the pump is to be firmly anchored to a base surface
(see Figure 14.)
If equipment is to be shipped directly from Milton Roy

into long term storage, contact Milton Roy to arrange
for factory preparation.
Increased reliability can be expected if pump locations

are avoided which are subjected to high ambient temperatures above 100F (38C) with poor free-air circulation over the pump assembly.
Pump Drive
1. Remove motor and flood the gearbox compartment
with a high grade lubricating oil/rust preventative such
13
2.5
OUTDOOR INSTALLATIONS
Figure 14. Mounting Bolt Holes

2.7 ELECTRICAL CONNECTIONS
The mRoy pump is designed as a totally enclosed unit

suitable for installation either indoors or outdoors. However, for outdoor installations the pump mounting area
should be selected to provide protection against environmental extremes:
Check to be sure that the electrical supply matches the

pump motor nameplate electrical characteristics. Motor
rotation must be counter clockwise when viewed from
the top end of the motor.
1. Operation with continuous exposure to tropical or

subtropical sunshine with ambient temperatures
above 90F (32C), which would cause higher oil
temperatures and affect lubricity should be
avoided. Good installation practice would dictate
providing a sun shade cover over the pump with
open sides to obtain the best air circulation
around the pump.
ON SINGLE-PHASE PUMP MOTORS THE

ROTATION WILL BE DETERMINED AT THE
FACTORY AND MUST NOT BE CHANGED.
ON THREE-PHASE PUMP MOTORS THE
ROTATION MUST BE DETERMINED AT THE
TIME OF INSTALLATION AND PRIOR TO
START-UP.
OPERATION
WITH
THE
WRONG ROTATION WILL DAMAGE THE
PUMP AND MOTOR AND VOID THE WARRANTY. SHAFT ROTATION CAN BE
OBSERVED BY REMOVING THE COVER
PLATE OVER THE ELECTRICAL CONNECTIONS.
2. Frequent start-up where the pump has been idle

in an ambient temperature below 30F (-1C) is
not recommended. Provide a removable,
insulated enclosure over the pump and mounting
base with provisions for an electrical heater (100
watt light, heat lamp, heater tape etc.) to
maintain the pump oil temperature above 30F (1C).
2.6
2.8
FLANGE MOUNTED MOTORS
MOTORS
Adequate power is provided to the simplex mRoy A

pump by the standard HP (0.2 Kw) motor. The motor
is normally a totally enclosed non-ventilated, type, that
is mounted on a 56C-face flange or IEC Frame 71
flange. The gear reducer (worm shaft) fits onto the
standard motor without using a coupling.
If a flange mounted motor option was selected for the

mRoy pump, the customer supplied motor will need to
be mounted to the pump. This is generally a straight
forward procedure. Refer to Figure 18 or 19, as appropriate.
On the larger mRoy B (Figures 10-13), the normal temperature rise for these motors is 50C above ambient
temperature, and it can be expected that these motors
will appear to operate at higher temperatures than are
normally experienced. However, there is no cause for
worry if the following precautions are observed:
When mounting the motor to a NEMA 56C Close Coupled Flange (product code option SR, refer to Figure
19), the motor mount plate (710) must be removed
from the pump body and bolted to the motor. The
motor/motor mount plate assembly can then be bolted
to the pump.
14
1. The motor is placed where there is adequate

ventilation and is protected against excessive
radiation from steam pipes and other heat
sources.
Nominal Oil Capacity

Pump Model
2. The overload heater in the starting device should

be correctly sized for motor full load current
rating as shown on the motor data plate.
2.9
Simplex
Duplex
mRoy A
1 Qt.
(.95 liters)
2 Qts.
(1.9 liters)
mRoy B
3 Qts.
(2.8 liters)
4 Qts.
(3.8 liters)
PUMP LUBRICATION
2.10
PIPING
General
CAREFULLY TWIST AND PULL TO
REMOVE OIL RESERVOIR CAP. DO NOT
APPLY PRESSURE TO JOG CAP FROM
SIDE TO SIDE OR DIP STICK MAY BREAK.
Refer to Figure 16 for a diagram of a typical recommended piping system.

Support all piping connections to the pump so that no
stress is placed on pump fittings. In no case should the
piping be sprung to make the connections to the pump.
The suction and discharge cartridge pipe connections
can be positioned within an arc of approximately 150
to facilitate piping to pump.
Oil is supplied for the average installation (ambient

temperature above 50F (10C). See recommendation
below for lower temperature. Fill pump and gear box by
slowly pouring the proper oil through the air bleed reservoir opening until the oil level in the reservoir is level
with oil level mark on outside surface of reservoir. Level
can also be checked with dipstick on oil reservoir cap.
Recheck while pump is operating.
Flush and blow out all pipelines before connecting the

pump. This eliminates any foreign matter that might
seriously damage the internal working parts of the liquid end. Install a 20 mesh Y-type strainer that is sized
to remove foreign particles with minimum pressure
drop in the suction line of the pump.
Install shut-off valves, with unions on the pump side of
the valves, in the suction and discharge lines to facilitate servicing.
DO NOT OVER FILL AS MOTOR DAMAGE

CAN RESULT.
NOTE: Synthetic oils are available that span the
entire temperature range. Contact Milton Roy for
further information.
Use extreme care in piping to plastic liquid end pumps

with rigid pipe such as PVC. If excessive stresses or
vibration is unavoidable, flexible connections are recommended.
Recommended Oil
NOTE: Many pipe joint compounds are not suitable for use with plastic pipe and, if used, will
cause stress cracking at the connection. Use only
compounds commended for use with plastic materials.
Any equivalent oil is acceptable.

Oil Type
Ambient
Temp. 15-50 F
(-9-10 C)
Ambient
Temp. Above 50F
(10 C)
AGMA Spec No. 2 EP
No. 5 EP
Suction Piping
Zurn Oil Co
No. EP 35
No. EP 95
ISO Grade
68
220
The suction piping must be absolutely tight and leakfree. For mRoy pumps on water-like solutions we recommend that the suction pipe be minimum diameter
and a maximum of 6 feet (2 meters) long. The intent is
that the piping must be designed to provide an adequate net positive suction head (NPSH). Obtain our
NPSH Calculation software at the Milton Roy Web site
(miltonroy.com). If assistance in determining NPSH is
15
needed, contact the Milton Roy Aftermarket Service

department.
pressure on the pump if a separate back pressure

valve is not used (mRoy A Figure 15 and 21, mRoy B
Figure 25). The back pressure spring should slip easily
through the hole in the seat. Do not disassemble the
seat and/or ball from metallic check valves. These
check valves are precision manufactured at Milton Roy
and should not be disassembled in the field.
A flooded suction is recommended for optimum service

life and maintenance-free operation. However, the
mRoy pump can operate with less than flooded suction
if necessary, in accordance with the following schedule
shown in the chart below.
2.11
Model
Number
Min. NPSH
Max. Lift
(PSIA)
(Ft. (meter)
H2O)
mRoy A
RA
10
10 (3)
mRoy H/T
RH or RT
10
10 (3)
mRoy P
RP
10
10 (3)
RS
10
5 (1.5)
RM
10
5 (1.5)
RB
10
2 (.6)
mRoy B
BACK PRESSURE SPRING INSTALLATION
Refer to Installation with Suction Lift, which outlines

limiting conditions if suction lift requirements are anticipated.
The supply tank should incorporate a low-level switch
to cut off the pump motor circuit before the suction
intake is exposed to air. Otherwise, the pump may
occasionally run dry.
Figure 15. Back Pressure Spring Installation

The plastic liquid end mRoy B pumps (Figure 25) always use a back pressure spring in the discharge cartridge, so retrofitting the back pressure spring into the
discharge is not required on these pumps.
Discharge Piping
The installation of an external Safety Valve is recommended, since the pumps internal relief valve is not intended to protect the piping system. Refer to Setting
the Relief Valve in Section 3, for further relief valve
discussion. (Milton Roy offers a complete line of back
pressure and safety valves).
AFTER PUMP HAS BEEN FULLY PRIMED,

REMOVE THE CAP FROM THE BODY AND
INSERT SPRING THROUGH THE TOP SEAT
TO REST ON TOP OF THE BALL CHECK.
REPLACE CAP AND TIGHTEN UNTIL
FIRMLY SEATED ON BODY. DO NOT OVERTIGHTEN, AS O-RING PROVIDES THE
SEAL.
For satisfactory metering and capacity control, the discharge pressure at the pump must be 50 PSIG (3.5
Bar) Minimum for the mRoy A and 70 PSIG (4.8 Bar)
minimum for the mRoy B. Therefore, when the pump is
to discharge into an open system, a back pressure
device must be installed in the pump discharge cartridge or line. (except the mRoy A plastic design).
Installation of this spring will assure repetitive metering
accuracy.
A spring (1390) is attached to each pump (Metallic Liquid End) in a small cloth bag (1380) for installation in
the discharge cartridge to develop the required back
16
REMOTE HEAD SYSTEMS: DO NOT

INSTALL A BACK PRESSURE SPRING IN
THE DISCHARGE BALL CHECK CARTRIDGE OF DIAPHRAGM HEADS WHICH
ARE
REMOTE
MOUNTED
(NOT
ATTACHED TO THE MAIN HOUSING). A
SEPARATE BACK PRESSURE VALVE
MUST BE INSTALLED IN THE DISCHARGELINE FROM THE REMOTE HEAD CARTRIDGE.
TAKE CARE WHEN INSERTING THE DISCHARGE PIPE NIPPLE INTO THE BALL
CHECK CARTRIDGE. NIPPLE SHOULD
NOT EXTEND INTO CAVITY, CAUSING
CLAMPING OF THE SPRING AND RETARDING NORMAL OPERATION.
Figure 16. Typical Piping System Installation
17
2.11
OPERATION WITH SUCTION LIFT
For Dynamic NPSH (Condition 2)
It is desirable that the mRoy pump operate with a

flooded suction; however, operation with net positive
suction head (NPSH) less than atmospheric pressure
is possible.
Available NPSH = Pa Ph Pf Le (must be equal to or

greater than minimum NPSH as listed under Installation Instructions.
D
NPSH is the head available, above the vapor pressure

of the liquid being pumped, to feed the liquid into the
pump suction port. NPSH minimum is the head below
which the pump cavitates.
= Plunger Diameter (inches)
Dp = Pipe Diameter (inches)

Lp = Actual Length of suction pipe (feet)
Both values are calculated at the suction port of the

pump. In controlled volume pump applications, two
conditions must be considered in the selection of a
pump to meet the NPSH minimum requirements:
Le = Equivalent length of suction pipe including

allowance for fittings (feet)
Pa = Ambient pressure above liquid (PSIA)
1. At the start of the suction stroke, the liquid in the

suction line has no velocity and NPSH minimum
depends on the force necessary to accelerate
the liquid in the suction pipeline.
Ph = Head of liquid column above (+) or below

() center line of plunger (PSIA) equals
Head in feet x (0.435) (Sp.Gr.)
2. At the peak of the suction stroke there is no

acceleration factor and NPSH minimum depends
on friction losses as calculated from standard
flow equations. With all viscous fluids and in pilot
plants and other places where unusual numbers
of fittings and valves are used, the second
condition that includes friction losses should be
considered. For water-like fluids, the first
condition will define the limiting configuration.
Pv = Vapor pressure of liquid (PSIA)

Pf = Friction loss per foot of pipe calculated
from Reynold Number evaluation (PSIA)
(Use 3.2 times average velocity for
calculating friction losses when referring to
a standard pipe losses table.)
Minimum NPSH = Minimum hydraulic pressure
at plunger (listed under
Installation Instructions).
For Static NPSH (Condition 1)

Available NPSH = Pa + Ph Pv (must be equal to or
greater than minimum NPSH as listed under Installation Instructions.
Required NPSH min =
When operating the pump with a NPSH of less than

atmospheric pressure (negative suction head or suction lift), special attention should be given to keep the
suction line strainer clean and prevent other system
conditions that might inadvertently decrease the NPSH
available.
Sp. Gr. (0.0925) LpD

Dp2
NOTE: Obtain our NPSH calculation software at

the Milton Roy web site (miltonroy.com). If assistance in determining NPSH is needed, contact the
Milton Roy Aftermarket Service Department.
18
SECTION 3
OPERATION
3.1 INITIAL START-UP
Before initial start up of the pump, check the following:
instructions. During these short runs listen for any

abnormal motor or crank noises, and if present, refer to
Section 5, Troubleshooting.
WARNING
Run pump for 1/2 to 1-1/2 hours to warm up oil. Check

discharge line for indication of flow.
Increase capacity adjustment setting to 100% of capacity and operate for 1020 minutes
FAILURE TO CHECK TORQUE ON NONMETALLIC HEAD BOLTS PRIOR TO

STARTUP AND AFTER ONE WEEK OF
OPERATION MAY EXPOSE OPERATING
PERSONNEL TO HAZARDOUS LIQUIDS.
1. Check the torque on all non-metallic head bolts
prior to startup. Recheck torque on all nonmetallic head bolts after pump has been
operating for one week. Torque the head
assembly screws in a crosswise pattern (Figure
17) as follows:
DO NOT SET THE CAPACITY ADJUSTMENT

KNOB IN EXCESS OF 100% BECAUSE
ERRATIC OR REDUCED METERING WILL
DEVELOP.
Reduce capacity adjustment setting to 3040% of maximum capacity and operate for several minutes, then
increase capacity adjustment back to 100% for approximately 10 minutes. Repeat several times to insure that
the air is bled from the pump displacement chamber
and the liquid end. (As a general rule, to bleed air or
vapor from the pump oil displacement chamber reduce
the capacity adjustment to the 20 to 40% range, and to
bleed air or vapor from the liquid end increase capacity
to 100%, or if possible reduce the discharge pressure
to atmospheric pressure for 30 seconds to one minute.)
a) mRoy Model A Plastic Heads: 6070 in. lbs.

(7-8 N-m) bolting torque.
b) mRoy Model B Plastic Heads:7585 in. lbs.
(8.5-9.6 N-m) bolting torque, tie down nuts
25 in. lbs. (3 N-m).
2. Oil level in air bleed filler reservoir up to or
slightly above the indicated oil level.
3. Set the capacity control knob to approximately
30-40% of maximum capacity.
The pump is now ready for on-line service. Calculate

what the desired capacity as a percentage of either the
maximum capacity rating on the pump data plate, or
the nominal capacity at the required system pressure.
Each pump is tested at the factory to confirm that the
performance meets these capacity-pressure requirements (when tested with water). (Milton Roy offers a
complete line of calibration columns for calibrating the
pump.)
4. Make certain that the suction line, liquid end and

discharge cartridge are filled with water or
system fluid.
5. Relieve all back pressure in the discharge line
and pump hydraulic system to allow air to purge.
Reduce pressure on the oil relief valve until air is
purged. Refer to Start-Up after the Suction
System has Run Dry section.
Start-Up with Back Pressure Spring in Discharge

Cartridge
6. If practical, install a temporary discharge line

piped back to the suction tank incorporating a
100 PSI (7 Bar) relief valve to facilitate
establishing performance during first hours of
operation.
The start-up procedure with the back pressure spring

installed is identical to the above procedure; however,
the back pressure device will hold air in the liquid end.
It is necessary to make certain that the liquid end is
filled with fluid, either by removing the discharge cartridge and filling liquid end and inlet lines before start
up, or by backing out the discharge cartridge cap
approximately seven (7) turns to remove the spring
load on the ball check permitting the air in the liquid
end to be discharged.
On initial start-up, run the pump for 1020 seconds,

then stop for 2030 seconds. Repeat a few times in
order to fill the diaphragm oil cavity. Check for proper
motor rotation as described in general installation
19
Start-Up after the Suction System has Run Dry
Relief Valve Setting
In applications where the suction tank does not have a

low level cutoff interconnected into the pump motor circuit, the pump may occasionally run dry. This should
be avoided to insure full integrity of the diaphragm.
Running the pump dry occasionally will not harm the
diaphragm or the pump. When the pump is repeatedly
allowed to run dry, especially for long periods of time,
the diaphragm is fatigued and could fail before the next
scheduled replacement.
Pump must be at operational pressure and capacity set

at 95%.
1. Remove yellow plastic plug located at top of
pump next to the oil fill hole.
2. Using a 3/16 hex. key (mRoy A), or a 5/16 hex.
key (mRoy B) as required for the different
models, turn the adjusting screw clockwise to
increase cracking pressure until pump ceases to
bypass through the relief valve at the desired
working pressure. When relieving has stopped,
adjust the screw clockwise up to one full turn
beyond this point to set a reasonable buffer zone
between operating pressure and relief pressure.
To determine if relieving is taking place, insert
your index figure into the oil reservoir opening
and place it against the bypass opening (Figure
18) where the oil pulse from the relief valve can
be determined.
Before restarting a pump that has run dry, provisions

should be made for filling the liquid end with liquid by
opening the discharge line to atmospheric pressure to
either refill liquid end with flooded suction pressure or
start pump with open discharge and run for a short
period of time (up to 2 minutes) that will prime the liquid end if the ball checks are wet. If these steps fail,
remove the discharge cartridge and fill liquid end with
liquid through the top discharge opening in the
head.After establishing flow, return to the regular discharge system configuration.
3.2
NOTE: No moving parts are present in the oil reservoir in this location.
RESETTING THE RELIEF VALVE
DESCRIPTION
3. Reinstall the plastic screw plug.
The mRoy pump incorporates an internal relief valve

that is preset at the factory to relieve when the hydraulic fluid pressure exceeds 125 PSIG (8.6 Bar). This setting can be readjusted as required up to 15% above
the maximum rated pressure of the pump. Resetting
the internal relief valve will change the potential discharge pressure of the pump.
WHEN RELIEVING IS TAKING PLACE,

ESPECIALLY ON PUMPS WITH THE LARGE
PLUNGER SIZES, OIL MAY BE EJECTED
AT HIGH VELOCITY FROM THE BYPASS
PORT. NORMAL PRECAUTION SHOULD BE
OBSERVED TO PREVENT THIS FROM
SPLASHING THE SURROUNDING AREA.
Refer Figure 19 for a pictorial description of the mechanism.

Examination of these drawings will reveal a small passage connecting the oil side of the diaphragm head
cavity with the oil reservoir (See Figures 1 & 2). This
passage is stopped off by a poppet that is held in place
by a spring secured by a set screw. A plastic screw
plug keeps the adjusting threads free of dirt.
NOTE: This relief is intended primarily for pump

protection in the event that the discharge or suction
system is blocked while the pump is in operation. It
is a good practice to install a high-grade chemical
type relief valve in the pump discharge line as
close to the pump as possible, and always
between the pump and any shut-off valve. Pipe the
outlet of the system relief valve back to the suction
tank, with the open end of the pipe visible at all
times. In this way, relief valve leakage may be easily detected.
In operation, the spring-loaded poppet is held against

the seat in the housing until the pressure in the oil side
of the diaphragm cavity exceeds the pressure for which
the valve has been set. When this occurs, the poppet is
forced off its seat, permitting the oil to flow from the diaphragm cavity through the mechanical passage to an
opening (Figure 18) in the side of the oil reservoir. The
resilient material of the poppet permits the relief valve
to actuate without erosion of the poppet or seat surface.
20
the pump is recommended every 24 or 48 hours to

visually confirm satisfactory operation:
1. Make sure the oil level in the air bleed filler
reservoir is above the oil level mark.
FOR SAFETY REASONS, A CHECK VALVE

IS RECOMMENDED FOR USE IN THE DISCHARGE LINE NEAR THE POINT WHERE
THE LINE ENTERS A HIGH-PRESSURE
PROCESS VESSEL.
3.3
2. Inspect the pump liquid end for indication of

leakage or seepage.
If anything seems to be amiss, refer to Section 4, Maintenance.
OPERATION
The mRoy pump is designed for reliable, unassisted

operation. During normal operation, a periodic check of
21
22
SECTION 4
MAINTENANCE
4.1 SPARE PARTS
1
3
To avoid excessive downtime in the event of a parts

malfunction, the spare parts shown below should be
maintained in your stores to support each mRoy pump.
For your convenience, these parts can be purchased
either separately or packaged in the form of Routine
Preventive Maintenance (RPM) Kits. RPM kit numbers
are listed in Section 1, Figure 7 (mRoy A) & Figure 13
(mRoy B).
Parts Orders Must Include The Following Information:

1. Quantity required (in this manual)
2. Part number (in this manual)
3. Part description (in this manual)
4. Pump model no. (on pump nameplate)
Double quantities required for duplex pumps. Two diaphragms are required for double diaphragm simplex
liquid ends; four are required for double diaphragm
duplex liquid ends.
4.2
5. Pump product code (on pump nameplate)

6. Pump serial no. (on pump nameplate)
Always include the serial number, product code, and
model number in all correspondence regarding the
unit.
RPM KIT COMPONENTS
mRoy A, B, H, T, J, & P Metallic Liquid End

1
Relief Valve Poppet
Suction Check Valve
Discharge Check Valve
4.3
Check Valve O-Ring
Split Ring
Square Ring (not use on RH/RT or mRoy B)
Ball (used on model P only)
NOTE: Federal law prohibits handling of equipment that is not accompanied by an OSHA Material
Safety Data Sheet (MSDS). A completed MSDS
must be packed in the shipping crate with any
pump returned to the factory. These safety precautions will aid the troubleshooting and repair procedure and preclude serious injury to repair
personnel from hazardous residue in the pump liquid end.
mRoy A Plastic Liquid End

1
Relief Valve Poppet
Suction Check Valve
RETURNING UNITS TO THE FACTORY
Pumps will not be accepted for repair without a Return

Material Authorization Form, available from the Aftermarket Department. Process liquid must be flushed
from the pump liquid end, and oil should be drained
from the pump housing before the pump is shipped.
Label the unit clearly to indicate the liquid being
pumped.
Diaphragm(s) of various sizes

2
Diaphragm
Check Valve O-ring

Diaphragm(s) of various sizes
Check Valve Seals
Square Ring
All inquiries or parts orders should be addressed to

your local Milton Roy representative or sent to:
Tube Coupling Nut (used on tube connection

checks only)
Parts Department
Milton Roy Company Flow Control Division
mRoy B, M, & S Plastic Liquid End
201 Ivyland Road
Relief Valve Poppet
Ivyland, PA 18974-0577
Suction Check Valve
Phone: (215) 441-0800
FAX (215) 441-0735
23
4.4
ROUTINE MAINTNANCE
however, Milton Roy Company recommends that the

mRoy diaphragm be replaced yearly to coincide with
check valve replacement. Also whenever the head is
removed freeing the diaphragm the diaphragm must be
replaced. Refer to the instructions in the Corrective
Maintenance section for diaphragm replacement.
The mRoy pump is designed for reliable service with a

minimum amount of maintenance required. However, a
yearly tune-up is recommended, during which the
check valves, diaphragm, and relief valve poppet are
replaced. For convenience, these parts are available in
a Routine Preventative Maintenance (RPM) Kit from
your local representative. RPM kit numbers are listed in
Section 1, Figure 7 (mRoy A) & Figure 13 (mRoy B).
4.5
4.8
Milton Roy Company recommends that the relief valve

poppet be replaced yearly during preventative maintenance. This can usually be timed to coincide with
check valve replacement. Refer to the instructions in
the Corrective Maintenance section.
SEMI ANNUAL OIL CHANGE
The oil in the main housing should be drained twice a

year, using the drain plug provided, and new oil
installed. This can usually be scheduled to coincide
with the change from winter to summer grade lubricants and vice versa. Refer to Pump Lubricants in
Section 2, Installation, for information on recommended oil and oil capacity.
4.9
CHECK VALVE CARTRIDGES
Milton Roy Company recommends that check valves

be replaced on an annual basis. If highly corrosive
material (acids, slurries, etc.) is being pumped, some
applications may require more frequent replacement.
In general, poor or reduced pump performance indicates that the check valves need to be replaced (refer
to Section 5, Troubleshooting).
4.9.1 Check Valve Cartridge Replacement
Complete instructions for replacing worn check valve

parts are given in the Corrective Maintenance section.
With the exception of the model A and L plastic versions, mRoy suction and discharge check valve cartridges are precision and assembled at the factory. Do
not attempt to disassemble these cartridges. If they
become inoperative flush them with Safety Solvent,
wash them with warm detergent and blow them out
with compressed air to remove any foreign matter. If
this treatment does not eliminate the trouble, the cartridge assembly should be replaced. mRoy A plastic
suction and discharge check valve cartridges may be
disassembled for cleaning or parts replacement.
The mRoy check valves are complete assemblies manufactured at the factory and should not be disassembled in the field.
To determine if the check valves need replacement,
with the pump off and pressure removed from system
unscrew the check valve from the liquid end and peer
through the hole in the check valve seat. The ball
should appear perfectly round and free of pits, mars, or
scratches. If the ball and/or seat is excessively damaged, the replacement schedule should be shortened
accordingly. If the ball and seat are both in good condition, the replacement schedule can be lengthened.
4.7
CORRECTIVE MAINTENANCE
BEFORE CARRYING OUT ANY SERVICING

OPERATION ON THE METERING UNIT OR
PIPES, DISCONNECT ELECTRICAL POWER
FROM THE PUMP. TAKE THE NECESSARY
STEPS TO ENSURE THAT ANY HARMFUL
LIQUID IN THE PUMP OR PIPING SYSTEM
CANNOT ESCAPE OR COME INTO CONTACT WITH PERSONNEL. SUITABLE PROTECTIVE
EQUIPMENT
MUST
BE
PROVIDED. CHECK THAT THERE IS NO
PRESSURE BEFORE PROCEEDING WITH
DISMANTLING.
NOTE: When adding oil, pour in a thin, slow

stream to avoid overflow.
4.6
RELIEF VALVE POPPET
4.9.1.1 Metallic Liquid Ends (Figures 20, 21, 22 &

25)
Disassembly
1. The check valve cartridge assemblies use an
SAE straight thread with an O-ring seal to
facilitate port alignment with the connecting
pipes. To remove the cartridge from the liquid
DIAPHRAGM(S)
The mRoy PTFE diaphragm is extremely durable and

often lasts for many years. As a preventative measure,
24
end, first loosen the lock nut (520) one or two

threads then unscrew the cartridge.
2. Remove and discard the O-ring (540) and spiral
back-up ring (530).
SUCTION AND CHECK VALVE CARTRIDGES ARE NOT IDENTICAL. BE SURE

THAT THE CORRECT CARTRIDGE IS
BEING SCREWED INTO THE PROPER
PORT. (DISCHARGE CARTRIDGES HAVE
HEXAGONAL CAP ON THE TOP; SUCTION
CARTRIDGES DO NOT.) IF CHECK VALVE
CARTRIDGES ARE INSTALLED INTO THE
WRONG PORT, ONE OF THE FOLLOWING
WILL OCCUR: (A) IMMEDIATE SEVERE
DAMAGE TO PUMP MECHANISM, (B) NO
PUMPING, (C) REVERSE PUMPING ACTION
(FROM DISCHARGE LINE INTO SUCTION
LINE).
3. On model mRoy P pumps only, the ball in the

suction port of the liquid end is not sealed inside
the suction check valve. This ball should fall out
easily when the suction check valve is removed.
4. Carefully clean any parts to be reused. If any
chemicals are used in the cleaning process,
ensure that they are compatible with the process
liquid.
Reassembly
1. To install the cartridge, position the lock nut (520)
toward the shoulder of the cartridge so that the
recess on the face of the lock nut is adjacent to
the O-ring (540) land (thread undercut) in the
cartridge.
6. After completing pipe connection, tighten lock nut

(520) securely against spotface so that O-ring
(540) is trapped in chamfer of liquid end thread.
Make sure that the spiral back-up ring (530) is
completely contained in its recess and not
extending to the outside.
2. Make certain the spiral back-up ring (530) is

coiled in a counterclockwise helix (this is
opposite the direction normally employed by
suppliers of these rings. Fit the spiral back-up
ring (530) in the lock nut (520) recess. Push it
firmly down in the recess as completely as
possible.
4.9.1.2 mRoy A Plastic Liquid End, Current Design

(Figure 20)
Disassembly
1. Unscrew the check valve assembly from the
pump liquid end.
3. Install new O-ring (540) against the spiral backup ring (530).
2. Both the suction and discharge check valves

may be disassembled in the same way. While
carefully holding the body use a 5/16 rod to
push out the internal parts. Do not damage the
sealing face (opposite the threaded end) on the
valve body. It is essential to reinstall the ball
guides and ball stop in the proper direction, so
take note during disassembly and follow the
assembly drawing.
NOTE: To assure a tight, leak free seal, new orings and spiral back-up rings should be used each
time the check valves are disassembled.
4. On model mRoy P pumps only (Figure 20), the
separate ball (570) needs to be balanced on the
end of the suction check valve cartridge so that it
will be held in place in the suction port by the
check valve when it is screwed in.

liquid.
5. Screw the cartridge assembly into the liquid end

until the O-ring band is approximately level with
the top of the spotface in the liquid end, then
screw it in one (1) additional turn plus a partial
turn as required to align the pipe thread port with
connecting pipe.
Reassembly
NOTE: To assure a tight, leak free seal, new seals
and O-rings should be used each time the check
valves are disassembled.
1. Lightly coat the O-rings on the ball guides with
mineral oil or other food grade lubricant. It is
25
essential to reinstall the ball guides and ball stop

in the proper direction. Remember the ball
always lifts off the seat in the direction of fluid
flow. The ball stop is used to retain the last ball
check on the suction cartridge.
cartridge (517). Slip the bolts (521) through the

holes in the compression plate and diaphragm
head so that they fall through and hang out the
bottom.
4. Fit a new o-ring (540) into position on the top of
the suction cartridge.
2. Remove the old valve-to-head seal (435) from

the head and install a new seal. A fracture of the
diaphragm head may result from installing the
check valve against two seals or excessive
tightening. The groove in the seal is to be
oriented against the check valve body.
5. Slip the suction cartridge and o-ring up into the

suction port of the liquid end. Position the other
compression plate (518) under the suction check
valve by sliding it up on the bolts. Screw on the
two remaining nuts (519). The suction check
should now be held in place in the liquid end.
Tighten the nuts on the through bolts firmly. Do
not over-tighten or plastic fittings may be
damaged.
4.9.1.3 mRoy B Plastic Liquid End (Figure 25)

Disassembly
1. The mRoy B plastic check valves are held to the
liquid end by two long bolts (521) that extend
through the diaphragm head. Unscrew the nuts
(519) on one end of these bolts to remove the
check valves from the liquid end. Use caution
when doing so, as the suction check valve and
compression plate (518) will fall off when the bolt
is removed.
4.9.2 Relief Valve Poppet Replacement (Figure 19)

If the pump is allowed to operate for long periods with
the relief valve relieving pressure, there is a possibility
that the poppet will wear, causing erratic flow and discharge pressure. If this occurs, the relief valve poppet
should be replaced. Even if excessive wear has not
occurred, it is still recommended that the poppet be
replaced on a yearly basis.
2. Remove and discard the check valve o-rings

(540).
Disassembly
liquid.
1. Unscrew and remove the relief valve screw plug

(1350).
2. Unscrew and remove the relief valve adjustment
screw (50).
Reassembly
NOTE: To assure a tight, leak free seal, new orings should be used each time the check valves
are disassembled.
3. Remove the relief valve spring (40). A pair of

tweezers may be required to fish the spring from
the relief valve port.
1. The discharge check valve consists of two

separate pieces that are shipped held together
with masking tape. Leaving the masking tape in
place during assembly will make the process
easier. These parts already have an o-ring in
place between them.
4. Remove the relief valve poppet (30) with a

tweezer or by jogging the motor, causing oil to
flow up through the relief port to float the poppet
up and out of the threaded hole.
Reassembly
2. Drop a new o-ring (540) into position in the

discharge port of the liquid end. Slip the entire
discharge cartridge (still held together with
masking tape) into the discharge port (only one
end will fit in).
1. Temporarily glue a new poppet (30) into the

end of the spring (40) with thick grease. Drop this
assembly into place in the relief valve port.
2. Install the relief valve adjustment screw (50) until
the spring (40) is lightly compressed. Follow the
instructions for resetting the relief valve given in
Section 3, Operation.
3. Screw a nut (521) two or three turns (just enough

to hold) on one end of each through bolt. Slide
the compression plate over the discharge
26
4.9.3 Diaphragm Replacement (Figures 20-27)
7. Carefully position the diaphragm head and

contour plate (this diaphragm head side contour
plate is not used on some models) in place,
aligning bolts holes. Remove blade and torque
bolts as follows (See Figure 17):
The different mRoy models (A, B, H, T, M, P, S & double diaphragm) all have slightly varying diaphragm configurations. Be sure to refer to the appropriate Figure
(20-27) when replacing the diaphragm(s).
a. mRoy Model A, H, T, & P Metal Heads:

265275 in. lbs. (30-31 N-m) bolting torque
(grade 5 or stronger bolts)
Disassembly
1. Remove the six (6) or eight (8) bolts (350 or 355)
from the diaphragm head (330), depending on
the model.
b. mRoy Model A Plastic Heads:

6070 in. lbs. (7-8 N-m) bolting torque
2. Remove diaphragm (290) using knife blade.
c.
3. Remove contour plate(s) (282).
mRoy Model B, M, & S Metal Heads:

340360 in lbs. (38-41 N-m) bolting torque
d. mRoy Model B Plastic Heads:

7585 in. lbs. (8.5-9.6 N-m) bolting torque
tie down nuts 25 in. lbs. (3 N-m).
4. If servicing a pump with a square ring (260),

remove and discard the square ring.
5. If servicing a double diaphragm style pump,
remove the intermediate chamber and square
head plated pipe.
Procedures for complete disassembly of the mRoy

pump are listed below. Some steps can be omitted
depending on which part is replaced.

liquid and hydraulic oil.
4.9.4 Motor and Worm Replacement (Figures 18 &

19)
The motor will need to be removed in order to replace
or inspect the motor or the gears.
Reassembly
Disassembly
1. Place pump on its side with diaphragm cavity

facing up.
1. Remove oil drain plug and drain oil.
2. Install contour plate(s) (282) into position in the

housing and/or diaphragm head (330), as
appropriate.
2. Remove the screws that attach the motor to the

pump.
3. If servicing a pump with a square ring, fit a new

square ring (260) into position in the recessed
square ring groove in the housing.
3. On plate mounted units, remove motor; the gear

shaft may come out as well. If the motor
separates from the worm shaft (640), use care
not to lose the shaft key and coil spring.
4. Carefully center diaphragm (290) in the shallow

recess in the housing.
4. Remove worm assembly (120).

5. On units with API motor mount adapters; removal
of the motor and adapter together will also lift the
worm gear shaft from the pump.
5. If servicing a double diaphragm style pump,

position the intermediate chamber and square
head plated pipe over the diaphragm. Fit a
second new square ring (260) (if required) into
position in the recessed square ring groove.
Carefully center the second diaphragm (290) in
the shallow recess in the intermediate ring.
Reassembly
1. Reinstall by reversing steps 1 through 5 or follow
the motor conversion directions.
6. Retain diaphragm with thin, flat blade 1/2 to l

wide.
27
4.9.5 Control Spool O-Rings Replacement (Figure

18, 20, & 21)
4.9.6 Worm Gear Replacement (Figure 18)

Disassembly
Occasionally, the control spool o-rings may need to be

replaced. Replacement is usuall indicated if pump
delivers less rated flow than expected.
1. Remove motor assembly, following instructions

shown in Motor and Worm Replacement
section.
Disassembly
1. Remove E-ring (220).
2. Remove two screws (250), linkage arm (240),

and control plunger (230).
2. Unscrew and remove capacity control knob

(210).
3. Use arbor press or hammer and brass punch to

remove the gear shaft from the gear.
3. Remove screw (180) in threaded sleeve (170)

(capacity control).
4. Lift worm gear, connecting rod, and plunger

assembly up and out of pump housing.
4. Remove diaphragm head (330), diaphragm

(290), contour plate (280 & 285), and motor and
motor mount.
Reassembly
5. Remove control spool (160) from bore.
4.9.7 Connecting Rod and Plunger Replacement

(Figure 18)
1. Reverse steps 1 through 4 above.
6. For mRoy A pumps, fabricate a tool by inserting

a 3/16 diameter x 4-in. long soft plastic (e.g.
Nylon) solid rod into the 3/16 hole and shaping
the end with a 7/16 reamer inserted into the
control spool bore. For the mRoy B pumps, a tool
is not required.
Disassembly
1. Lift connecting rod (100) up and back to
disengage plunger (90) from bore.
2. Use arbor press or hammer and brass punch to
remove wrist pin (110) from connecting rod (100)
and plunger (90).
3. To assure proper installation, note position of oil
groove for wrist pin (110) and oil groove for worm
gear (120) with respect to connecting rod (100)
and plunger (90). Groove should be located at
bottom of bore.
CAREFUL USE OF REAMER IS HIGHLY

RECOMMENDED
AS
DAMAGE
MAY
OCCUR TO THE SURFACE OF THE BORE.
A TOOL, P/N - ORINGTOOL CAN BE PURCHASED FROM MILTON ROY.
Reassembly
Reassembly
1. Reverse steps 1 through 3 above. Be sure to

properly align oil groove to its original position,
as noted in step 3.
1. Place new O-rings (150) on control spool (160)

and coat O-rings liberally with grease to hold
them in place.
2. Place O-ring tool (notch facing up to guide O-ring
across intersecting passage), into 3/16 hole at
12:00 oclock position behind the contour plate.
3. Push control spool and O-rings into bore
carefully, using O-ring tool to guide O-ring across
intersecting passage. This is done to prevent
damage to O-rings. Finally, guide control piston
into center of control spool, motor side.
28
Figure 17. Diaphragm Head Bolt Torque Pattern
29
30
SECTION 5
TROUBLESHOOTING GUIDE
SYMPTOMS
Pump motor wont operate.
REMEDIES
No power. Supply correct power in accordance with motor
nameplate.
Blown fuse. Check for short circuit or overload.
Open thermal overload device in starter. Reset overload.
Broken wire. Locate and repair.
Low voltage. Check for too thin wiring.
Low liquid level (where low level cutoff is used). Fill tank.
Oil is frozen in pump. Thaw out.
Bad motor. Replace motor.
Pump doesnt deliver rated capacity.
Starved suction. Replace suction piping with larger size, or

increase suction head.
Leaky suction piping. Repair or replace defective piping.
Excessive suction lift. Rearrange equipment location to
reduce suction lift.
Liquid too close to boiling point. Lower temperature or
increase suction pressure.
Air in hydraulic or reagent system. Bleed system.
Air or gas trapped in oil or pumpage. Decrease capacity to
20% for 5 mins. then increase to 100% for 5 mins.
Worn or dirty valves or seats. Clean or replace cartridges.
Viscosity of liquid too high (cps). Reduce viscosity by heating
or other means, or increase size of suction piping, or
increase suction pressure.
Insoluble materials; crystallization of liquid; settling of solids.
Limit solution strength to proper value. Flush and clean solution tank periodically. Suction connection should be 2 to 4
from bottom of solution tank.
Low discharge pressure. A minimum discharge pressure is
required to insure proper capacity control (see Discharge
Piping, Section II.)
Relief valve being actuated. Refer to symptom marked with
an *.
Capacity adjustment set above 100% capacity mark. Reposition adjustment knob to 100% mark.
Pump delivers erratically.
Leaky suction line. Repair or replace piping.

Worn or dirty valves or seats. Clean or replace cartridges.
Excessive excursion of ball valves from seats (indicated by
ball chatter). Replace cartridges.
Insufficient suction pressure. Increase suction pressure by
raising tank level or pressurizing suction tank.
Liquid too close to boiling point. Reduce temperature or raise
suction pressure.
Leaky system relief valve. Repair or replace relief valve.
31
SYMPTOMS
REMEDIES
Motor overheats thermal overload switches. Power supply does not match motor characteristics. Check
power supply against motor nameplate data.
Overload caused by operating pump above its discharge
pressure. Check operating pressure against pump manufacturers data plate max. rating and correct the cause of the
pressure abnormality.
Noisy operation of pump liquid end.
Pump valves must move to open and close, and they will
make a clicking noise as they operate. These noises are
sometimes amplified by natural resonances in the piping system. They are usually indications of normal valve functioning.
Noisy operating in drive casing (pounding Fluid compressibility causes reversal load on gears at end of
noise at high discharge pressure).
pressure stroke. Not considered detrimental. No action
needed.
Pump internal relief valve actuating, caused by excessive
suction lift conditions. Lower pump or raise level of liquid.
Pump internal relief valve actuating, caused by insufficient
suction pressure. Correct poor suction condition.
Pump internal relief valve actuating, caused by clogged or
partially blocked filter or strainer in suction line. Clean
strainer.
Pump internal relief valve actuating, caused by clogged or
fouled suction or discharge check valves. Clean or replace.
Pump internal relief valve actuating, caused by blocked discharge line. Remove blockage.
Pump internal relief valve actuating, caused by insufficient
discharge pressure. Install back pressure valve or device to
create back pressure at pump discharge connection (see
Discharge Piping, in Section II).
Improper oil level in reservoir increases and Flexible diaphragm punctured by foreign material. Replace
overflows.
diaphragm.
Pump delivery is not adjustable.
System pressure too low. Install a back pressure valve in the

discharge line (preferred method), or install a back pressure
spring (provided) into discharge cartridge.
Pump does not develop required pressure.
Refer to symptom marked with an *, or check to see if system

pressure exceeds rated capacity on data plate.
O-rings on control spool are nicked. Replace O-rings. (Note:
you must use a special tool. See section on control spool disassembly.)
Carefully review causes and remedies for the second and
third symptoms listed.
32
SECTION 6
PARTS
6.1 GENERAL
1. This section gives information regarding replaceable
components.
6.2
ILLUSTRATED PARTS LIST
1. Figure and Item Number Column

a) The item numbers shown in the detailed parts
list correspond to the item numbers appearing
on the exploded view illustration. To find an
unknown part number, locate the part on the
illustration and note the item number. Look for
the item number on the detailed parts list. The
part number is on the same line. A dash (-) precedes non-illustrated item numbers.
2. Description Column
a) The name of the item is in the description column.
3. Part Number Column
a) The suppliers part number is listed in the part
number column.
4. Material/SPM Column
a) The material used to manufacture the part is
listed in the material/SPM column.
b) The strokes per minute is listed for all worm
and shaft assemblies in the material/SPM column.
5. Quantity Column
a) The numbers appearing in the quantity column
are the total quantity of the listed part required
in its immediate assembly.
33
Figure 18. Common Parts - mRoy A & B Side View and API Motor Mount
(DWG(s) 102-1971-0001 and 102-1971-0003)
34
Figure 19. Common Parts - mRoy A & B End View and mRoy A Close Coupled Motor Mount
(DWG(s) 102-1971-0003 and 102-1971-300)
35
Figure 20. mRoy A Metallic and Plastic Liquid End

(DWG 102-1971-0002)
36
Figure 21. mRoy A Metallic Low Pressure and High Pressure Liquid End
(DWG 102-1971-0002)
37
Figure 22. mRoy A Bar Stock Liquid End (DWG 102-1971-00019)
38
Figure 23. mRoy A Double Diaphragm and Leak Detection

(DWG(s) 102-1971-0002 and 102-1971-0005)
39
Figure 24. mRoy A and B Actuator (DWG(s) 102-1971-0003 and 102-1971-0004)
40
6.3
BASIC PARTS LIST FOR DRIVE MODELS RA, RH, RT, RJ, AND RP (FIG. 18 &19)
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
10
Housing, Main
Consult with aftermarket group for replacement. Provide serial number and model number of pump.
20
Cup, Race
409-0064-020
Steel
30
Poppet, Relief Valve
212-0056-074
Nylon
40
Spring, Relief Valve
280-0043-041
Steel
50
Adjusting Screw, Relief Valve
405-0241-014
Steel
60
Plug - 1/4" NPT, Sq. Head
402-0009-111
Steel
70
Gear Shaft Bushing, (factory

installed, not recommended for field
service, call factory)
237-0029-006
Steel
80
Housing Sleeve 7/16", RA and RP

(plunger factory in-stalled, not recommended for field service, call factory).
237-0073-006
Steel
Housing Sleeve for 5/8", RA and

RP (plunger factory in-stalled, not
recommended for field service, call
factory).
237-0060-006
Steel
Plunger, 7/16"
212-0055-006
Steel
Plunger, 3/8
212-0055-106
Steel
Plunger, 5/8"
212-0054-006
Steel
Plunger, 1-1/16"
212-0053-006
Steel
100
Rod, Connecting
214-0025-062
Aluminum
110
Pin, Wrist
211-0030-006
Steel
120
Gear, Worm (Ratio 77:1)
252-0125-001
15/23 spm Simplex
252-0127-001
15/23 spm Duplex
252-0052-001
37 spm Simplex
252-0053-001
37 spm Duplex
252-0090-201
73 spm Simplex
252-0091-001
73 spm Duplex
252-0019-200
117 spm Simplex
252-0026-001
117 spm Duplex
Gear, Worm (Ratio 9.5:1)
252-0086-201
185 spm Simplex
252-0087-001
185 spm Duplex
Gear Spacer, Simplex
219-0071-006
Steel
Gear Spacer, Duplex
219-0109-006
Steel
Gear Shaft, Simplex
268-0021-006
Steel
Gear Shaft, Duplex
268-0018-006
Steel
90
125
130
- Parts Not Illustrated

Parts Continued Next Page
41
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
140
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
Plug, 1 NPT Socket Hex Head, RA

and RP
402-0095-061
Plug, 1/2 NPT Socket Hex Head,

RJ, RT, and RH
402-0095-041
150
O-Ring, Parker 2-011
408-0109-082
Polyurethane
160
Control Spool
268-0037-006
Steel
170
Sleeve, Threaded
243-0058-016
316SS
180
Screw, Socket Set - 6-32NC x 1/4
405-0039-035
190
Plate, % Capacity
253-0015-062
Aluminum
200
Ring, Calibration
253-0024-062
Aluminum
Ring, Calibration
253-0024-071
PVC
Knob, Control
255-0019-016
316SS
Knob, Capacity Adjust
255-0019-071
PVC
Knob, Capacity Adjust, (Locking

Micrometer)
255-0045-000
220
E-Ring - 1/4", Control Knob
404-0124-096
Steel
230
Plunger, Control
212-0036-039
Steel
240
Arm, Linkage
214-0009-006
Steel
250
Screw, Linkage - 8-32 x 1/4" Socket

head
405-0245-011
Steel
1062
Screw, Socket Head - 6-32 x 1, Locking Micrometer Knob
40201
Steel
1063
Nut, Hex Head - 6-32NC (Locking

Micrometer)
405-0060-017
Steel
1330
Cap, Reservoir With O-Ring
30256
Cap, Reservoir
20183
1340
O-Ring, Reservoir Cap
408-0095-071
NBR
1350
Screw Plug, Relief Valve
405-2001-011
Plastic
Screw, Mount Data Plate
405-0280-000
Steel
Plate, Data
253-0186-000
Decal, Caution Motor
253-0021-198
210
Lubrication
-
Oil, Gear - EP-35
407-0195-010
1 Quart
Oil, Gear - EP-95
407-0152-010
1 Quart
Oil, Gear - EP-95
407-0152-040
1 Gallon
A/R

42
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
6.4
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
PARTS COMMON TO LIQUID END MODELS RA, RP, AND RJ (FIGURE 20 & 21)
260
Ring, Sq. - 3.75 Id x 1/8wall (Models

RA, RJ, and RP only)
408-0144-010
NBR
280
Contour PlateOil Side - 3-1/2"
298-0061-016
316 SS
285
Contour Plate-Process Side, Also

Used With Double Non-Contacting
Diaphragms)
298-0061-016
316SS
298-0061-028
Alloy 20
298-0061-030
Alloy C-22
460
O-Ring, Discharge Check Valve Cap
408-0068-043
PTFE
510
Cartridge, Discharge Assembly
221-0897-216
316SS
221-0897-228
Alloy 20
221-0897-230
Alloy C-22
520
Nut, Locking, Check Valve
209-0020-014
Stainless Steel
530
Back-up Ring, Spiral, Check Valve

Lock Nut
408-0073-141
PTFE
540
O-Ring, Check Valve Lock Nut
408-0068-065
FKM (VITON)
600
Cartridge, Suction Assembly (Double

Ball) 1/2" NPT Connection, (Except
Model RP)
221-0896-216
316SS
221-0896-228
Alloy 20
221-0896-230
Alloy C-22
402-0001-045
316SS
402-0001-049
Alloy 20
280-0033-016
316SS
280-0033-030
Alloy C-22
280-0033-026
Alloy C-276
1390
Bushing, Reducing - 1/2" x 3/8", Used

To Install New Suction Check Valve
to 3 - 8" piping.
Spring - Discharge Cartridge, when
required
Diaphragm Head Designs And Diaphragms Are Grouped According To Size And Are Not Interchangeable
6.5
DIAPHRAGM HEAD DESIGN- 6 BOLT (5" WITH HOLES) LIQUID END MODEL RA (FIGURE 21)
290
300
325
Diaphragm, 6 Bolt Design (5" With

Holes)
298-0106-075
PTFE
Diaphragm, PEEK, 6 Bolt Design (5"

With Holes)
298-0123-000
PEEK
Ring, Intermediate, Leak Detection,

(Contacting Diaphragm)
219-0111-016
316SS
Ring, Intermediate Chamber, Double

(Non-Contacting) Diaphragm
221-0865-016
316SS
Contour Plate- (Process Side) Leak

Detection, (Contacting Diaphragm)
298-0091-016
316SS
298-0091-028
Alloy 20

43
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
330
350
6.6
DESCRIPTION
Head, Diaphragm - 6 bolt, 5" Diaph.

Design 1996 (Models RA, RL, and
RP)
PART NUMBER
MATERIAL/SPM
QUANTITY
221-0859-001
Cast Iron
221-0858-016
316SS
221-0858-029
Alloy 20
21194
Alloy C-22
Screw, Hex Head - 5/16" x 1-1/4"
405-0017-139
Steel
Screw, Hex Head - 5/16" x 1-1/2"

Leak Detection Ring/Head.
405-0017-149
Steel
Screw, Hex Head - 5/16" x 2" Double

Diaphragm/Head.
405-0017-169
Steel
DIAPHRAGM HEAD DESIGN- 8 BOLT (2-7/8") LIQUID END MODEL RH & RT (FIGURE 21)
281
Pin, Spring - 0.062 x
401-0001-061
Steel
282
Contour PlateOil Side - 2-1/2

(After 1998)
298-0107-006
Steel
Contour PlateOil Side - 2-1/2

(Before 1998)
298-0007-016
316 SS
Contour Plate-Process Side
298-0007-016
316SS
298-0007-028
Alloy 20
287
289
O-Ring - 2-039
21146
Viton
290
Diaphragm - 2-7/8" Diameter, 8 bolt

Diaphragm Design
298-0005-275
PTFE
330
Head, Diaphragm - 2-7/8" Diameter,

8 bolt Diaphragm design
221-0179-001
Cast Iron
221-0179-016
316SS
221-0179-029
Alloy 20
221-0179-030
Alloy C-22
350
Screw, Socket Head - 5/16-18, 1-1/4"
405-0028-134
Steel
355
Screw, Socket Head - 5/1618, 2-1/2"
405-0028-184
Steel
460
408-0068-043
PTFE
510
Cartridge Assembly, Discharge

(Double Ball)
221-0897-216
316SS
221-0897-228
Alloy 20
221-0897-230
Alloy C-22
520
Nut, Locking, Check Valve
209-0020-014
Stainless Steel
(303SS)
530
Ring, Spiral Back-up, Check Valve

Lock Nut
408-0073-141
PTFE
540
O-Ring, Check Valve Lock Nut
408-0068-065
FKM (VITON)

44
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
600
1390
6.7
Spring, Discharge Check Valve
MATERIAL/SPM
QUANTITY
221-0896-216
316SS
221-0896-228
Alloy 20
221-0896-230
Alloy C-22
280-0033-016
316SS
280-0033-030
Alloy C-22
280-0033-026
Alloy C-276
290
Diaphragm, 8 bolt - 4" Diameter
298-0005-175
PTFE
330
Head, Diaphragm - 8 bolt, 4" Diameter
221-0632-116
Replaces Cast Iron
Model RJ and all 5/8" Plunger

Pumps Prior To 1996
221-0632-116
316SS
221-0632-129
Alloy 20
21324
Alloy C-22
Screw, Hex Head - 5/16-18, 1-1/4"
405-0017-139
Steel
Screw, Hex Head, Double Diaphragm/ Head
Call Factory
Steel
Screw, Hex Head - 5/1618, 2-1/2"
405-0017-189
Steel
221-0859-001
Cast Iron
221-0858-016
316 SS
221-0858-029
Alloy 20
21194
Alloy C-22
407-0014-172
316 SS
407-0014-173
Alloy 20
407-0014-076
Alloy C
221-0864-016
316 SS
221-0864-028
Alloy -20
221-0864-030
Alloy C-22
355
MODEL RP SUCTION CHECK VALVE PARTS (FIGURE 20)

330
570
600
6.9
Cartridge Assembly, Suction (Double

Ball) 1/2" NPT Connection
PART NUMBER
DIAPHRAGM HEAD DESIGN- 8 BOLT (4") LIQUID END MODEL RJ (FIGURE 21)
350
6.8
DESCRIPTION
Head
Ball Check, Suction - 5/8
Valve Body, Suction
MODEL RA12 PLASTIC LIQUID END PARTS (FIGURE 20)

260
Sq. Ring 3.75 ID x 1/8 Wall (Models

408-0144-010
NBR
280
Contour Plate(Oil Side
298-0061-016
316 SS
290
Diaphragm 5"
298-0106-075
PTFE
330
Head
221-0845-071
PVC

45
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
340
Plate, Back-Up
271-0054-015
Steel
350
Screw, Hex Head - 5/16-18 x 2
405-0017-163
18-8 SS
360
Base, Simplex Mroy A
201-0441-006
Steel
Base, Duplex Mroy A
201-0434-006
Steel
370
Screw, Hex Head - 5/16-18 x 1-1/4

Gr5
405-0017-139
Steel
390
Lock-Washer, Spring - 5/16
404-0040-028
Zinc Plated
400
Nut, Hex - 5/16-18NC
405-0065-013
18-8 SS
435
Seal- Head to Check Valve (PVC

Checks)
408-0143-075
PTFE
500
Nut, Coupling - Tubing Connection

ONLY
407-0350-079
490
Check Valve Assembly, Suction Tube End
20287
PVC
O-Ring - 3/8 x 3/32
225-0032-675
PTFE
Ball Stop
20289
PVC
Seat
20290
PVC
Ball, 3/8 Ad995
407-0015-111
Ceramic
Body, Cartridge
20288
PVC
Suction Assembly, NPT
20299
PVC
O-Ring - 3/8 x 3/32
225-0032-675
PTFE
Ball Stop
20289
PVC
Seat
20290
PVC
Ball, 3/8 Ad995
407-0015-111
Ceramic
Body, Cartridge
20291
PVC
Discharge Assembly-Tube End
20292
PVC
O-Ring - 3/8 x 3/32
225-0032-675
PTFE
Ball Stop
20289
PVC
Seat
20290
PVC
Ball, 3/8 Ad995
407-0015-111
Ceramic
Body, Cartridge
20288
PVC
Discharge Assembly, NPT
20302
PVC
O-Ring - 3/8 x 3/32
225-0032-675
PTFE
Ball Stop
20289
PVC
Seat
20290
PVC
Ball, 3/8 Ad995
407-0015-111
Ceramic
Body, Cartridge
20291
PVC
Parts
Included
490
Parts
Included
495
Parts
Included
495
Parts
Included

46
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
6.10
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
MROY RA MOTOR MOUNT PARTS (FIGURES 18 & 19)

Close Coupled Flange Mount NEMA 56C (SR)
SR (NEMA 56C) Worm and Shaft Assembly includes Worm Shaft (640), Worm (650), Pin (660), Cone Bearing
(670) and Spring (740).
Worm and Shaft Assembly
21594
77:1 23 spm @1725 RPM
21593
48:1 37 spm @1725 RPM
21590
24:1 73 spm @1725 RPM
21591
15:1 117 spm @1725 RPM
21592
9.5:1 185 spm @1725 RPM
640
Shaft, Worm
252-0157-006
650
Worm
252-0126-006
77:1
252-0051-006
48:1
252-0090-106
24:1
252-0019-100
15:1
252-0086-106
9.5:1
Steel
Steel
660
Pin, Spring
401-0005-091
670
Bearing, Cone
409-0064-010
710
Plate, Motor Mount
272-0130-062
720
Gasket, Motor
225-0115-099
730
Screw, Socket Head - 3/8 - 16 x 5/8
405-0029-086
Steel
740
Spring, Compr. Lee LHL-625-C-1
403-0166-011
Steel
770
Screw, Socket Head - 1/4-20 x 1
405-0027-111
Steel
1
Aluminum
1
2
Close Coupled Flange IEC Frame 71, B5 (SS)

SS (IEC Frame 71, B5) Worm and Shaft Assembly includes Worm Shaft (640), Worm (650), Pin (660), Cone
Bearing (670) and Spring (740).
252-0158-600
77:1 23 spm @1725 RPM
252-0158-700
48:1 37 spm @1725 RPM
252-0158-800
24:1 73 spm @1725 RPM
252-0158-900
15:1 117 spm @1725 RPM
252-0158-110
9.5:1 185 spm @1725 RPM
640
Shaft, Worm
252-0167-006
650
Worm
252-0126-006
77:1
252-0051-006
48:1
252-0090-106
24:1
252-0019-100
15:1
252-0086-106
9.5:1

47
Steel
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
660
Pin, Spring
401-0005-091
670
Bearing, Cone
409-0064-010
710
Plate, IEC Motor Mount
272-0142-062
720
Gasket, Motor
225-0115-099
Gasket, Motor IEC71
225-0121-099
730
SHCS - 8 MM x 1.25 x 30
405-2007-074
740
Spring
60059
770
Screw, Socket Head - 1/4 - 20 x 1
405-0027-111
Steel
QUANTITY
1
1
Aluminum
Steel
4
1
Steel
Parts Common To ALL API Motor Mounts

FR (NEMA 56C) Stub Shaft Assembly includes Worm Shaft (640), Worm (650), Pin (660), Cone Bearing (670), &
Ball bearing (680).
Stub Shaft Assembly
252-0144-500
77:1 23 spm @1725 RPM
Stub Shaft Assembly
252-0144-100
48:1 37 spm @1725 RPM
Stub Shaft Assembly
252-0144-400
24:1 73 spm @1725 RPM
Stub Shaft Assembly
252-0144-000
15:1 117 spm @1725 RPM
Stub Shaft Assembly
252-0144-300
9.5:1 185 spm @1725 RPM
640
Shaft, Worm
252-0110-006
650
Worm
252-0126-006
77:1
252-0051-006
48:1
252-0090-106
24:1
252-0019-100
15:1
252-0086-106
9.5:1
Steel
Steel
660
Pin, Spring
401-0005-091
670
Bearing, Cone
409-0064-010
680
Bearing, Ball
409-0094-020
API Flange Mount NEMA 56C (FR)

75
Plug, Expansion - 9/32
40059
Steel
690
Washer, Flat
219-0030-006
Steel
700
Spring, Finger - 0.563
403-0121-006
Steel
710
Adapter, Motor
272-0090-001
Cast Iron
770
Screw, Socket Head - 8-32NC x 3/4
405-0132-031
Steel
780
Coupling - 1/2 x 5/8 Key
410-0127-040
790
Screw, Hex Head - 3/8-16 x 1 GR5
405-0018-119
Steel
800
Plug, Sq. Head Pipe - 1/2" NPT
402-0009-137
Steel

48
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
API Flange Mount NEMA 143/145TC (F4)

75
40059
Steel
690
Washer, Flat
219-0030-006
700
403-0121-006
710
Adapter, Nema 56c - 143/145 TC
272-0090-001
770
405-0132-031
780
Coupling - 5/8 x 7/8 3/16 Key
410-0064-120
790
Screw, Hex Head - 3/8-16 x 1 GR5
405-0018-119
800
402-0009-137
Steel
Steel
Steel
API Flange Mount NEMA IEC Frame 71, B5 (FS)

75
40059
690
Washer, Flat
219-0030-006
700
403-0121-006
710
Adapter, Motor, mRoy A API IEC
272-0146-001
770
405-0132-031
780
Coupling - 1/2 x 14MM(Lovejoy L095)
40202
405-0065-013
Screw, Hex Head - 3/8-16 x 1 Gr5
405-0018-119
404-0040-028
402-0009-137
790
800
Steel
4
1
Steel
Steel
Steel
API Flange Mount IEC 80 B5 (MD)

75
40059
690
Washer, Flat
219-0030-006
700
403-0121-006
710
Adapter, Motor - IEC 80 B5
272-0090-001
Plate, Motor Adapter
60199
770
405-0132-031
780
Coupling - 5/8 x 19mm (Lovejoy l100)
40244
790
Screw, Hex Head - M10 x 25mm
435-0001-732
Steel
800
402-0009-137
Steel

49
Steel
4
1
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
6.11
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
ELECTRONIC CAPACITY CONTROL MOUNTING (FIGURE 24)
Complete Kits: 30268 for 7/16, 3/8, & 5/8 plungers & 335-1401-040 for 1-1/16 plunger) Parts included are below:
140
Plug, Adapter - 1-1/16 Plunger (1"
243-0045-020
Steel
1
NPT)
6.12
Plug, Adapter - 7/16, 3/8, & 5/8

Plunger (1/2" NPT)
243-0045-000
Steel
150
O-Ring, Parker - 2-011
408-0109-082
Polyurethane
160
Control Spool
268-0037-006
Steel
170
Sleeve, Threaded
243-0058-016
316SS
180
Screw, Socket Set - 6-32NC x 1/4
405-0039-035
190
Plate, % Capacity
253-0015-062
Aluminum
200
Ring, Calibration
253-0024-062
Aluminum
210
255-0035-077
Acetal
213
Bearing, Control Spool ECC
237-0076-052
217
Washer, Thrust - 5/16
404-0147-031
Steel
220
E-Ring (1/4" for Control Knob)
404-0124-096
Steel
810
Coupling, Drive ECC
252-0138-077
820
Lock-Washer - #6
404-0104-071
Steel, Zinc Plated
830
Screw, Pan Head - 6-32NC x 3/8
405-0178-033
18.8SS
840
Bracket, Mounting, Mroy A ECC
204-0149-006
860
Nut, Serrated Flange - 1/4-20NC
405-0323-036
Steel, Zinc Plated
880
Screw, Socket Head - 5/16-18 x 5/8
405-0157-024
Steel / Nylon
900
Actuator (mRoy)
per SPEC
910
Shaft, Drive ECC Assembly: Includes

Items 915 & 920.
268-0055-000
915
Pin, Dowel - 1/8" Assemble w/2680052-077
401-0021-133
920
Pin, Spring - 0.187dia.x 5/8
401-0005-032
Steel
930
Lock-Washer, Spring - 3/8"
404-0041-022
18.8SS
935
Screw, Hex Head - 3/8-16 x 3/4
405-0018-096
Steel, Zinc Plated
950
Guard, Left Side ECC
249-0110-006
Steel
960
Guard, Right Side ECC
249-0109-006
Steel
970
Screw, Button Head - 10-32 x 5/16
405-0282-087
18.8SS
1440
Mroy ECC Instruction Manual
339-0083-000
PNEUMATIC CAPACITY CONTROL (3-15 PSI DIRECT, FIGURE 24)

150
408-0109-082
215
Adapter
272-0052-017

50
Polyurethane
3
1
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
6.13
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
220
E-Ring (1/4" for Control Knob)
404-0124-096
Steel
980
Flange, Mount mRoy A PCC
204-0070-062
Aluminum
990
O-Ring - 0.921 x 0.139
408-0095-041
NBR
1000
Lock-Washer, Int. Tooth - #6
404-0104-071
Steel, Zinc Plated
1010
Screw, Rd. Head - 6-32NC x 7/16
405-0002-061
Steel, Zinc Plated
1020
Screw, Slotted Shoulder - 5/16-18
405-0299-000
Steel
1030
408-0109-082
Polyurethane
1040
Piston
212-0051-062
Aluminum
1050
O-Ring, - 2-226
408-0095-171
NBR
1060
Screw, - 1/4-20 x 1/2
405-0112-039
Steel, Zinc Plated
1070
Gasket, Pneumatic Cylinder
225-0073-098
1080
Cylinder, Pneumatic
281-0173-198
1090
Spring, Actuator
280-0041-000
1100
Gasket, Pneumatic Positioner
225-0030-098
1110
Stud
232-0010-106
1120
Postioner, Moore
403-0043-002
1130
Nut, Hex - 1/4-20NC
405-0064-012
1140
Decal, Pneumatic % Capacity
253-0029-198
1440
Mroy PCC Instruction Manual
339-0004-000
Steel
6
1
18.8SS
SIMPLEX LEAK DETECTION PARTS, FIGURE 23 (DOUBLE QUANTITIES FOR DUPLEX PUMPS)
260
Ring, Sq. - 3.75 Idx1/8wall (Models

408-0144-010
NBR
290
Diaphragm (5" with holes) RA
298-0106-075
PTFE
Diaphragm (4", 8 bolt design) RJ
298-0005-175
PTFE
Ring Assembly, Intermediate RA
219-0111-016
316 SS
Ring Assembly, Intermediate RJ
219-0127-000
316 SS
320
Contour Plate, Process Side
298-0091-016
316 SS
325
Contour Plate, Oil Side
298-0091-016
316 SS
350
Screw, Hex Head - 5/16-18 x 1-1/2

Gr5, RA and RJ
405-0017-149
Steel
355
Screw, Hex Head - 5/16-18 x 2-3/4

Gr5, RJ
405-0017-199
Steel
360
Base, Simplex Mroy A
201-0441-006
Steel
Base, Duplex Mroy A
201-0434-006
Steel
370
Screw, Hex Head - 5/16-18 x 1-1/4

Gr5
405-0017-139
Steel
380
Bracket
204-0199-006
Steel
300

51
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
390
404-0040-028
Zinc Plated
400
Nut, Hex - 5/16-18nc
405-0065-013
18-8 SS
1150
Check Valve - 1/8tube, 1/3 PSI
40065
316 SS
1160
Gage, Press - 0-400psi, Dual Flange

Mount
40066
Gage, Press - 1000psi, Dual Flange

Mount
40176
1170
Adapter, Red - 1/4f x 1/8m, NPT
40067
316 SS
1180
Tee, Branch - 1/8NPTf x 1/8 tube
40060
316 SS
1190
Tee, - 1/8npt Female
40062
316 SS
1191
Tee, - 1/8npt Female
40062
316 SS
1200
Tube Conn.- 1/8 Tube x 1/8 NPT
40061
316 SS
1201
Tube Conn.- 1/8 Tube x 1/8 NPT
40061
316 SS
1210
Valve, Bleed - 1/8 NPT
40063
316 SS
1220
Screw, Pan Head - 4-40 x 1/2
405-0263-050
Zinc Plated
1230
Lock-Washer, Spring #4
404-0095-023
18-8 SS
1240
Nut, Hex - 4-40nc
405-0182-012
18.8 SS
1250
Switch, Pressure, Nema 4 - 5-30 PSI
406-0388-001
1250
Switch, Pressure, Nema 7 - 5-30 PSI
406-0389-001
1260
Nipple, Red Hex - 1/2x1/8, NPT
40064
316 SS
1270
Screw, Hex Head - 1/4-20x3/4
405-0016-095
18-8 SS
1280
404-0039-022
18.8 SS
1290
Nut, Hex - 1/4-20nc
405-0064-012
18.8 SS
1300
Tubing, Pump To Gauge (formed)
249-0137-116
Tube - 1/8 od x 0.035 wall
402-0502-993
Tubing, Gauge To Switch Nema 4
249-0136-016
Tubing, Gauge To Switch Nema 7
249-0138-016
Tubing, - 1/8 od x 0.035 wall
402-0502-993
1440
Leak Detector Instruction Manual
339-0036-000
1470
Mineral Oil (available at drug stores)
1320

52
1
316 SS
316 SS
12 in.
20 in.
1
DRIVE MODEL RA
DRAWING
LOCATION
NUMBER
6.14
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
DOUBLE DIAPHRAM PARTS (FIGURE 23)

260
Ring, Sq. - 2-240S (Models RA,

RJ, and RP only)
408-0144-010
Nitrile
285
Contour Plate, Process Side, also

used with double non-contacting diaphragms)
298-0061-016
316SS
298-0061-028
Alloy 20
298-0061-030
Alloy C-22
Diaphragm (5" with holes), model

RA
298-0106-075
PTFE
Diaphragm (4", 8 bolt design), model

RJ
298-0005-175
PTFE
Ring Assembly, Intermediate
20536
Probe, Alarm Conductivity
301-0307-000
310
Plug, - 1/8 THRD. SQ Head Pipe
402-0011-013
350
402-0017-233
Oil, Vegetable
40104
290
300
-

53
Steel
6
0.013 Gal
Figure 25. mRoy B Metallic and Plastic Liquid End (DWG 102-2146-0002)
54
Figure 26. mRoy B Leak Detection With Switch and Gauge (DWG 102-2146-0004)
55
Figure 27. mRoy B Double Diaphragm (DWG 102-2146-0007)
56
6.15
BASIC PARTS LIST FOR DRIVE MODELS RB (RS, RM, RB) (FIGURES 18 & 19)
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
10
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
Housing, Main Simplex 19/32"
281-0104-101
Housing, Main Duplex 19/32"
281-0148-101
Housing, Main Simplex 7/8"
281-0104-301
Housing, Main Duplex 7/8"
281-0148-301
Housing, Main Simplex 1 7/16"
281-0104-201
Housing, Main Duplex 1 7/16"
281-0148-201
20
Cup, Race
409-0066-020
Steel
30
Poppet, Relief Valve
212-0057-074
Nylon
40
Spring, Relief Valve
280-0046-541
Steel
50
Adjusting Screw, Relief Valve
256-0037-051
Brass
60
Plug - 1/4" NPT, Sq. Head
402-0009-111
90
Plunger, 19/32 "RS"
22714
Plunger, 7/8 "RM"
22716
Plunger, 1-7/16 "RB"
22715
100
Rod, Connecting
214-0013-162
Aluminum
110
Pin, Dowel 5/8x1-1/2
401-0028-031
Steel
120
252-0094-201
48 spm Simplex
252-0095-001
48 spm Duplex
252-0082-201
72 spm Simplex
252-0058-001
72 spm Duplex
252-0092-201
96 spm Simplex
252-0093-001
96 spm Duplex
252-0081-201
144 spm Simplex
252-0057-001
144 spm Duplex
252-0088-201
148 SPM Simplex,

1425 RPM
Gear Shaft
268-0030-006
Simplex, Steel
Gear Shaft
268-0022-006
Duplex, Steel
Plug, 1-1/4 NPT, Socket Hex Head
402-0095-071
Plug, 3/4 NPT, Socket Hex Head,

Models RM & RS
402-0095-051
150
O-Ring, Parker 2-113, Control Spool
408-0068-032
Urethane
160
Control Spool
268-0049-006
Steel
170
Sleeve, Threaded, Mroy B ECC
243-0059-051
130
140

57
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
180
Screw, Socket Set, Cup Pt. - 6-32NC

x 1/4
405-0039-035
190
Decal, Capacity
253-0026-062
200
Ring, Calibration
253-0025-062
Aluminum
210
Knob, Control
255-0020-062
Aluminum
220
E Ring Clip, External
404-9983-151
230
Plunger, Control
212-0048-039
240
Arm, Linkage
214-0014-006
250
405-0245-031
Steel
1061
Screw, Socket Set - 7/16-14 x 3/8
405-0133-024
Steel
1062
Screw, Socket Head - 8-32 x 1-5/8

(Locking Micrometer)
40224
Steel
1063
Nut, Hex - 8-32 NC 18-8SS (Locking

Micrometer)
405-0061-017
Steel
1330
Cap, Reservoir Simplex
249-0106-276
Cap, Reservoir Duplex
281-0269-000
O-Ring, Parker - 2-216, Simplex,

Reservoir Cap
408-0095-071
BUNA
O-Ring Parker - 2-216, Duplex, Reservoir Cap
408-0095-075
VITON
Screw Plug - 7/8-14
405-2001-021
Plastic
Plate, Data
253-0186-000
Screw, Stick For Data Plate, 5/32
405-0280-000
Decal, Caution Motor
253-0021-198
1340
1350
1
Steel
1
1
Lubrication
6.16
Oil, Gear - EP-35
407-0195-010
1 Quart
Oil, Gear - EP-95
407-0152-010
1 Quart
Oil, Gear - EP-95
407-0152-040
1 Gallon
A/R
LIQUID END RB & RM (FIGURE 25)

280
Contour Plate - Oil Side
298-0012-006
Steel
285
Contour Plate - Process Side
298-0016-016
316 SS
298-0016-028
Alloy 20
298-0016-030
Alloy C-22
290
Diaphragm - 5.230 Dia.
298-0013-075
PTFE
350
Screw, Hex Head - 7/16-14 x 1-1/2

Gr5
405-0019-149
Steel
355
Screw, Hex Head - 7/16-14 x 2-3/4
405-0019-191
Steel

58
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
330
Head, Diaphragm
PART NUMBER
MATERIAL/SPM
QUANTITY
221-0214-001
Cast Iron
221-0215-016
316 SS
221-0215-029
Alloy 20
221-0215-030
Alloy C22
Base, Simplex
201-0395-000
Base, Duplex
201-0428-000
370
Screw, Hex Head - 5/16-18 x 1-1/2

Gr5
405-0017-149
Steel
390
404-0040-028
Zinc Plated
400
405-0065-013
18-8 SS
460
408-0068-043
PTFE
510
Check Valve Assembly, Discharge
221-0156-016
316 SS
221-0156-028
Alloy 20
30577
Alloy C22

(Slurry Applications)
22077
316SS
520
Nut, Lock
209-0021-017
416 SS
530
Back Up Ring, Spiral
408-0073-221
PTFE
540
O-Ring, Check Valve Locking Nut - 3916, 1.171 x 0.116,
408-9998-151
VITON
600
Check Valve Assembly, Suction
221-0154-016
316 SS
221-0154-028
Alloy 20
30578
Alloy C22

(Slurry Applications)
22078
316SS
Spring, Compression
280-0038-016
316SS
280-0038-026
Alloy C-276
1390
6.17
DESCRIPTION
LIQUID END RS (FIGURE 25)

280
298-0014-006
Steel
285
298-0014-006
Steel
298-0014-016
316 SS
298-0014-028
Alloy 20
298-0014-030
Alloy C-22
290
298-0015-075
PTFE
330
Head, Diaphragm
221-0212-001
Cast Iron
221-0213-016
316 SS
221-0213-029
Alloy 20

59
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
221-0213-030
Alloy C-22
350
Screw, Hex Head - 7/16-14 x 1-1/2
405-0019-149
Steel
355
Screw, Hex Head - 7/16-14 x 2-1/4
405-0019-171
Steel
Base, Simplex
201-0395-000
Base, Duplex
201-0428-000
370
Screw, Hex Head - 5/16-18 x 1-1/2

Gr5
405-0017-149
Steel
390
404-0040-028
Zinc Plated
400
405-0065-013
18-8 SS
460
408-0068-113
PTFE
510
Check Valve, Discharge
221-0897-216
316 SS
221-0897-228
Alloy 20
221-0897-230
Alloy C-22
520
Nut, Lock - Check Valve
209-0020-014
303 SS
530
Ring, Spiral Back Up
408-0073-141
PTFE
540
O-Ring, Check Valve Lock Nut - 2116,
408-0068-065
FKM (VITON)
600
Check Valve, Suction
221-0896-216
316 SS
221-0896-228
Alloy 20
221-0896-030
Alloy C-22
280-0033-016
316 SS
280-0033-026
Alloy C-22
1390
Spring
6.18 MODEL RB12 & RM12 PLASTIC LIQUID END PARTS (FIGURE 25)
Conversion Kit (P/N: PARTSKIT307) includes the following parts:
280
Contour Plate
298-0012-006
Steel
281
Pin, Orientation
211-0043-071
PVC
285
Contour Plate
298-0038-071
PVC
290
298-0013-075
PTFE
330
Head, Diaphragm
221-0359-071
PVC
Head Assembly Kit, Diaphragm

(Includes 330, 522, 523, 524, 526,
and 527)
221-0393-100
340
Reinforcing Plate, Upper
204-0088-016
316SS
345
Reinforcing Plate, Lower
204-0089-016
316SS
350
Screw, Hex Head - 7/16-14 x 2-1/2
405-0019-187
18-8S
355
405-0019-297
18-8SS
Base, Simplex
201-0395-000

60
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
510
6.19
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
Base, Duplex
201-0428-000

(Includes 430, 511, 512, 513, 514,
515, 516, and 541)
221-0464-007
PVC
221-0464-009
PVDF
517
Plate, Compression
204-0091-016
316 SS
518
Plate, Compression
204-0090-016
316SS
519
405-0065-013
18-8SS
521
Stud - 5/16-18UNC x 10 1/4
232-0014-216
316SS
522
Ball - 3/8 Dia.
407-0015-111
Ceramic AD995
523
298-0062-075
PTFE
524
Bushing - 1/2 NPT
237-0049-171
PVC
526
Plug, Purge
243-0047-171
PVC
527
Connector, (Tubing x )
402-0479-028
PVC
540
O-Ring, - 3-916, 1.171 x 0.116,

Check Valve
408-9998-151
FKM (VITON)
600
221-0360-007
PVC / Ceramic Ball
221-0360-009
PVDF
MROY RB MOTOR MOUNTS (FIGURES 18 & 19)

Parts Common To All Motor Mounts
Worm and Shaft Assembly includes Stub Shaft (640), Worm (650), Spring Pin (660), Tapered Roller Bearing (670),
and Single Roll Bearing (680).
252-0142-401
38:1 48 spm @1725 RPM
1
640
650
252-0142-000
25:1 72 spm @1725 RPM
252-0142-300
19:1 96 spm @1725 RPM
252-0142-100
12.5:1 144 spm @1725 RPM
252-0047-200
9.5:1 148 spm @1425 RPM
Stub Shaft
252-0143-006
Stub Shaft (9.5:1 Only)
252-0048-006
Worm
252-0094-106
38:1 48 spm @1725 RPM
252-0082-106
25:1 72 spm @1725 RPM
252-0092-106
19:1 96 spm @1725 RPM
252-0081-106
12.5:1 144 spm @1725 RPM
252-0088-106
9.5:1 148 spm @1425 RPM
660
Pin, Spring 0.187 x 1
401-0005-091
670
Bearing, Tapered Roller
409-0066-010
680
Bearing, Single Row
409-9994-000

61
Steel
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
API Flange Mount NEMA 56C (FR)

690
Seal, Oil
408-9997-011
700
Spring, Finger
403-0121-009
710
Adapter Nema 56c - 143/145 TC
272-0051-001
770
Screw, Socket Head - 10-32 x 3/4
405-0026-094
780
Coupling - 5/8 x 5/8, Key 3/16
410-0064-020
790
405-0018-119
Steel
2/4
1
Steel
API Flange Mount 143/145 TC

690
Seal, Oil
408-9997-011
700
Spring, Finger
403-0121-009
710
Adapter Nema 56c - 143/145 TC
272-0051-001
770
405-0026-094
780
Coupling - 5/8 x 7/8 3/16 Key
410-0064-090
790
405-0018-119
Steel
2/4
API Flange Mount IEC 80 B5

690
Seal, Oil
408-9997-011
700
Spring, Finger
403-0121-009
404-0041-022
18-8 SS
Nut, Hex - 3/8-16NC
405-0066-012
18-8 SS
710
607-20388-001
770
405-0026-094
780
Coupling Assembly - 5/8 x 19mm
39238
790
Screw, Hex Head - 3/8-16 x 1-1/4
405-0018-136
Zinc Plated
800
Plug, Sq. Head Pipe - 3/8"
402-0011-031
Steel
1
Steel
2/4
1
API Flange Mount IEC 90 B5

690
Seal, Oil
408-9997-011
700
Spring, Finger
403-0121-009
404-0041-022
18-8 SS
Nut, Hex - 3/8-16NC
405-0066-012
18-8 SS
710
607-20388-001
780
Coupling Assembly - 5/8 x 24mm
30459
790
Screw, Hex Head - 3/8-16 x 1-1/4
405-0018-136
Zinc Plated
800
Plug, Sq. Head Pipe - 3/8"
402-0011-031
Steel

62
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
6.20
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
ELECTRONIC CAPACITY CONTROL MOUNTING (FIGURE 24)

140
Plug, Adapter - 1-7/16 and 7/8

Plunger 1-1/4 NPT
243-0045-030
Plug, Adapter - 19/32 Plunger, 3/4

NPT
243-0045-010
170
Sleeve, Threaded Mroy B ECC
243-0059-051
180
Screw, Socket Set - 6-32NCx1/4
405-0039-035
190
Decal, Capacity
253-0026-062
200
Ring, Calibration
253-0025-062
Aluminum
210
255-0036-077
Acetal
213
Bearing, Control Spool
237-0075-052
217
Washer, Thrust - 1/2"
404-0147-051
220
Clip, E Ring - External
404-9983-151
810
Coupling, Drive
252-0120-077
820
Lock-Washer, Internal Tooth - 8
404-0104-082
Zinc Plated
830
Screw, Pan Head - 8-32NC x 1/2
405-0179-073
18-8 SS
840
Bracket, Mounting
204-0148-006
Steel
850
Stud, Mounting
232-0033-006
860
Nut, Serrated Flange - 1/4-20NC
405-0323-036
Zinc Plated
880
Screw, Socket Head - 5/16-18 x 5/8
405-0157-024
Steel
880
Bolt, Tri-Groove - 5/16 x 3/4 L
405-0336-011
900
Actuator, Mroy
Per Spec
910
Shaft, Drive
268-0053-077
Acetal
915
Pin, Dowel - 1/8 x 1-3/8
401-0021-143
Steel
920
Pin, Spring, 0.187 x 13/16 CRS
401-0005-062
930
404-0041-022
18-8 SS
935
Screw, Hex Head - 3/8-16 x 3/4
405-0018-096
Zinc Plated
950
Guard, Side
249-0108-006
970
Screw, Button Head - 10-32 x 5/16
405-0282-087
1442
Mroy ECC Instruction Manual
339-0002-000
1460
Label, Warning
253-0097-000
1
Steel
2
18-8 SS
6.21 SIMPLEX LEAK DETECTOR PARTS- GAUGE & NEMA SWITCH (FIGURE 26)
Double Quantities For Duplex Pumps
290
300
Diaphragm, 5.230 Dia.
298-0013-075
PTFE
Diaphragm, 3.390 Dia., RS
298-0015-075
PTFE
Ring Assembly, Intermediate
219-0089-116
316 SS
Ring Assembly, Intermediate RS
179-1260-116
316 SS

63
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
320
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
Contour Plate
298-0092-016
316 SS
Contour Plate
298-0092-028
C-20
Contour Plate, RS
298-0101-016
316 SS
Screw, Hex Head - 7/16-14 x 1-3/4
405-0019-151
Screw, Hex Head - 7/16-14 x 1-3/4,

RS
405-0019-151
Screw, Hex Head Screw - 7/16-14 x 3
405-0019-201
Screw, Hex Head - 7/16-14x3, RS
405-0019-181
356
405-0019-161
357
Washer, Flat - SAE 7/16
404-0151-013
Base, Simplex
201-0395-000
Base, Duplex
201-0428-000
Bracket, Switch
204-0159-006
Bracket, Switch, RS Only
179-1239-015
1150
Check Valve - 1/4 NPT
407-0315-701
1160
Gage, Press, 0-1500psi Dual Scale
403-0151-110
1175
Plug, Pipe - 1/4, Threaded, RS
402-0011-023
1190
Tee, Street - Ss-4st 1/4"
402-0560-022
1200
Connector, Male -1/8 x 1/2
402-0558-192
316 SS
1205
Elbow, Male - 1/8 tube1/4 NPT
402-0553-042
316 SS
1210
Plug, Valve - 1/4 Male/Female
407-0314-082
316 SS
1250
Switch, Pressure, Nema 4 - 5-30psi
406-0388-001
Switch, Pressure, Nema 7 - 5-30psi
406-0389-001
1270
Screw, Hex Head - 1/4-20x3/4
405-0016-095
18-8 SS
1280
Nut, Hex - 1/4-20NC
405-0064-012
18-8 SS
1290
Lock-Washer, Spring 1/4
404-0039-022
18-8 SS
1300
Pilot Line
249-0117-016
316 SS
Pilot Line, RS - 1/8 Dia.
179-1262-000
316 SS
Bracket, Support
204-0156-015
Bracket, Support RS
179-1238-015
1306
Bolt, - 1/4-20 "U" Clamp
410-0153-000
1440
Mroy Leak Detector Instruction Manual
339-0036-000
1470
Mineral Oil (available at drug stores)
407-0317-020
350
355
380
1305

64
Zinc Plated
316 SS
1
1
316 SS
1
2
Steel
1
1
Oz.
DRIVE MODEL RB
DRAWING
LOCATION
NUMBER
6.22
DESCRIPTION
PART NUMBER
MATERIAL/SPM
QUANTITY
DOUBLE DIAPHRAGM PARTS FOR METALLIC LIQUID END (FIGURE 27)

280
298-0012-006
285
298-0016-016
316 SS
298-0016-028
Alloy 20
298-0016-030
Alloy C-22
290
298-0013-075
PTFE
292
Intermediate Chamber
20539
316 SS
328
Oil, Vegetable
40104
350
Screw, Hex Head - 7/16-14 x 2 1/2
405-0019-181
Steel
355
Screw, Hex Head - 7/16-14 x 3 3/4
40894
Steel
601
Plug, Pipe - 3/8 Threaded
402-0011-033
316 SS
602
402-0011-013
316 SS
105-115 ml
(3.6-3.9 oz)
6.23 DOUBLE DIAPHRAGM PARTS- WITH CONDUCTIVITY PROBE FOR PLASTIC LIQUID END (RM &
RB) (FIGURE 27)
290
Diaphragm 5.230 Dia.
298-0013-075
PTFE
324
Intermediate Chamber
20539
316 SS
326
Probe, Alarm Conductivity
301-0307-000
Plug, Pipe - 3/8, Used without Alarm

Probe
402-0011-033
316SS
327
402-0011-013
316 SS
328
Oil, Vegetable
40104
355
Screw, Hex Head - 7/16-14 X 3 1/2
40448
18-8 SS
Screw, Hex Head - 7/16-14 X 6
40447
18-8 SS

65
105-115 ml
(3.6-3.9 oz)
66
APPENDIX A
MODEL CODE HISTORY
Mroy L History
R
No. of Liquid Ends
1= Simplex
Plunger Diameter
10 = 5/8"
Class
17 = 1-1/16"
R= Integral Motor
Materials of
Liquid End Type
Construction
L= "L" Range
7= Polypropylene
8= PVDF
PUMP SPECIFICATIONS (mRoy L) :
Liquid End: Hydraulically actuated, simplex only
Plunger Diameter: 5/8 or 1-1/16
Capacity Range: 0.2 GPH to 18 GPH (0.752 LPH to 68 LPH)
Mroy A History
67
Stroking Speed (SPM)

37 = 37 SPM
73 = 73 SPM
17 = 117 SPM
Milton Roy Company

www.miltonroy.com
201 Ivyland Road

Ivyland, PA 18974-0577
Phone: (215) 441-0800
FAX: 215-441-8620

339 0047 0001

Uploaded by

Copyright:

Available Formats

339 0047 0001

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

339 0047 0001

Uploaded by

Copyright:

Available Formats

Milton Roy

Please record the following data for file reference

Pumps Water Primed

Plumbing and Electrical Connections

Always adhere to your local plumbing and electrical codes.

Over Pressure Protection

Pump Operation With By-Pass Port Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Pump Operation With By-Pass Port Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

mRoy Data Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

mRoy A, H, J, and P Model Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

mRoy A, H, J, and P Gear/Motor Mount/Connection/Capacity Control; Select Mode Code. . . . . . . .5

mRoy A, H, J, and P Type of Liquid End; Select Mode Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

mRoy A, H, J, L, and P Routine Maintenance Kit List, By Model Code . . . . . . . . . . . . . . . . . . . . . . .6

mRoy A Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

FIGURE 8A. mRoy RT, RH, & RJ Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

mRoy P Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

FIGURE 10. mRoy B Capacity/Pressure Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

THIS PAGE INTENTIONALLY BLANK

The mRoy pump is a highly reliable controlled volume

For a general description of the mRoy pump you have

Historical Model Codes are found in Appendix A.

Pump capacity is adjustable while the pump is running

Pumping action is developed and controlled by four

Repetitive accuracy of the metered discharge volume

2. The flexible diaphragm X is a movable partition

3. An oil bypass circuit from the diaphragm

A plunger, reciprocating at a fixed stroke, displaces a

In operation, as the pump plunger and bypass control

Metering with repetitive accuracy is possible only if the

On the suction stroke, the pump plunger pulls oil out of

The discharge capacity is adjusted from 0100% by

opened when the plungers have completed one-half of

Figure 1. Pump Operation With By-Pass Port Open

Figure 2. Pump Operation With By-Pass Port Closed

MODEL CODE SELECTION

End item Model Code

mROY H/T SERIES

RH=7/16 Dia. Plunger

Option Select Number

mRoy H LIQUID END

Option Select Number

mRoy J LIQUID END MATERIAL

Option Select Number

mRoy P LIQUID END MATERIAL

Figure 4. mRoy A, H, T, J, and P Model Code

GEAR SET (ALL mRoy A FRAME)

MOTORS and MOUNTS

NOTE: Must be used when pump is not ordered with motor

Plastic Liquid Ends

Figure 5. mRoy A, H, T, J, and P Gear/Motor Mount/Connection/Capacity Control; Select Mode Code

RUPTURE DETECTION & BASE (mRoy A FRAME)

Base Only - Recommended with Flanges

Rupture Detection with Base & Gauge

Rupt. Detect. w/ Base, Gauge, & NEMA 4 Switch

Rupt. Detect. w/ Base, Gauge, & Ex. Prf Switch

Double Diaphragm with Base

Double Diaphragm with Base & Conductivity Probe

Plastic Liquid Ends