4860 DS

4860
Standard Electronic Voltage Dividers
The 4860 series (control unit and capacitive HV

divider with compressed gas and air capacitors) high
precision standard voltage divider is used as a variable
comparison standard in the differential method (bridge)
measurement of high voltage instrument transformers.
The special active guard controlled design of this
divider set results in highest accuracy.
This standard voltage divider is ideal for integration
with the 2767 or 2769 test set in a full remote
controlled instrument voltage transformer test system
FEATURES
Universal comparison standard for any transformer

ratios within a wide voltage range
Very accurate voltage divider ratio ( 50 ppm, 0.1

min)
Max. measurement voltage is dependent only on rated

voltage of compressed gas capacitor
For voltages less than 1000 V the electronic device can

be used without additional divider
VOLTAGE DIVIDER ARRANGEMENT

HIGH VOLTAGE DIVIDER UNIT
The high voltage divider unit comprises a capacitive
high voltage divider (compressed gas standard
capacitor C1 and air capacitor C2) and an electronic
device in series, constituting a variable electronic
divider (see system diagram). Capacitive voltage
divider C1/C2 divides the primary voltage Uprim to
voltage U1, which the electronic device matches to the
required secondary voltage Usec. Voltage instrument
transformers of less than 1 kV primary voltage can be
connected directly to the electronic system via the
adaptor box supplied with the divider.
Easy handling
Suitable for all Tettex (2767, 2765, 2711/22 and
2711/23) and many other manufacturers transformer

test sets
Direct replacement of earlier series 4850

Existing compressed gas capacitors can generally be
equipped to form a complete system.
Complete system is certifiable

Remote control possibility via IEEE 488 or RS 232C
interface
ELECTRONIC DEVICE
The main components of this system are an input
amplifier and a guard-potential control (up to 1010 V),
an electronic divider and a power amplifier with the
output stage. The instrument is protected against
setting errors, overvoltages and short-circuits. Errors
message are indicated on the dot matrix display.
Upgradeable
to an automatic
combination with a type 2767
test
system
by
A more cost-effective solution than inductive voltage

standard transformers, especially for high rated voltage
systems.
1/4
BASIC TEST SET-UP
Measurement circuit with capacitive divider for > 1 kV primary voltage
Legend for abbreviations used

PV
Primary rated voltage
SV
Secondary rated voltage
CR
Capacitive divider ratio (C-Ratio)
Uprim
Primary voltage
Usec
Secondary voltage
U1
Electronic divider input voltage
U
Test
voltage
(primary
or
secondary)
UR
Rated
voltage
(primary
or
secondary)
U/UR Excitation
ELECTRONIC STANDARD VOLTAGE DIVIDER

SERIES 4860 STANDARD SYSTEMS
C1 Type (gas)
[Serie/pF/kV]
C2 Type (air)
[Serie/pF]
Divider ratio CR
1 ... 1010 V*
1:1*
1 100 kV
3370 NK/100/100
3330/9900
1:100
1 100 kV
3370 NK/100/200
3330/9900
1:100
2 200 kV
3370 NK/100/200
3330/10000 + 3330/9900
1:200
1 100 kV
3370 NK/50/300
3330/4950
1:100
3 300 kV
3370 NK/50/300
3330/10000 + 3330/4950
1:300
4 400 kV
3370 NK/50/400
3330/10000 + 3330/9950
1:400
1 100 kV
3370 NK/50/400
3330/4950
1:100
4 400 kV
3370 NK/50/400
3330/10000 + 3330/9950
1:400
6 600 kV
3370 NK/33.3/600
3330/10000 + 3330/9946
1:600
1 100 kV
3370 NK/33.3/600
3330/3296
1:100
6 600 kV
3370 NK/33.3/600
1:600
8 800 kV
3370 NK/50/800
1 100 kV
3370 NK/50/800
8 800 kV
3370 NK/50/800
1 1200 kV
3370 NK/20/1200
3330/10000 + 3330/9946
3 x 3330/10000 +
3330/9950
3330/4950
3 x 3330/10000 +
3330/9950
2 x 3330/10000 +
3330/3980
Type
Measurement
range (Uprim)
4861
4861/100
4861/200
4861/300
4861/400a
4861/400b
4861/600a
4861/600b
4861/800a
4861/800b
4861/1200b
* range covered by any other type e.g. 4861/300
2/4
1:800
1:100
1:800
1:1200
TYPE 4861 STANDARD VERSION
GENERAL DATA
This version has up to two fixed voltage divider ratios

set by HAEFELY HIPOTRONICS, which the user
cannot change. The complete standard voltage divider
is therefore certifiable.
Power supply
TYPE 4862 CUSTOMIZED VERSION
Dimensions (W x H x D)
The user can set two ratios and change them

whenever needed. This standard divider is not
certifiable.
Weight
230/115 V, 50/60 Hz
Power requirement
approx. 100 VA
Storage and transport temperature
20 ...+ 70 C
500 x 310 x 470 mm

(19.7 x 12.2 x 18.5)
34 kg (74.8 lb)
ERROR LIMITS
TECHNICAL SPECIFICATIONS
Intrinsic error (electronic device)
ELECTRONIC SYSTEM TYPES 4861

Input
Max. input voltage U1
1010 V
Input resistance
> 10 G
Input capacitance
< 0.1 pF
Measurement signal frequency

(16 2/3 Hz on request)
45 65 Hz
In operating range
20 ... 200 % U/UR
Test frequency
50 or 60 Hz 1%
At reference conditions
50 ppm 0.1 min
At rated operating conditions
100 ppm 0.2 min
Reference and rated operating conditions according to

IEC 359, class I.
Additional errors
Max. guard capacitance

(for guard potential control)
10 nF
With extended operating range

5 ... 20% U/UR
50 ppm; 0.1 min
1 ... 5% U/UR
100 ppm; 0.2 min
Max. output voltage Usec
250 V
Max. power output for U/UR = 100%
5 VA
With extended frequency range

45 ... 65 Hz
50 ppm; 0.1 min
Max. output current for Usec 50 V
0.4 A
Max. load capacitance
10 nF
Output
With capacitive divider

C-divider calibrated and supplied by TETTEX
Instruments as per standard system table: no additional
errors
SYSTEM PARAMETERS
Rated primary voltage PV
Direct input range
With capacitive divider
Adjustment factors
Existing type 4850 electronic device replaced by type

4861: no additional errors
System calibrated and commissioned by TETTEX
Instruments on customers premises: additional errors
on enquiry
0.010 ...1.010 kV
(0.010 ... 1.010) x
1/CR [kV]
SERIES 3370 GAS CAPACITORS (C1)
x1, x1/3, x1/3
Technical specification as in leaflets of 3370 and 3380.

The low-voltage connection is provided with a triaxial
socket for use of the capacitor as a capacitive voltage
divider (series 3370). Optional triaxial/coaxial adaptor no.
008140-72 enables C/tan measurements.
Rated secondary voltage SV

Input range
5 ... 250 V
Adjustment factors
x1, x1/3, x1/3
SERIES 3330 AIR CAPACITORS (C2)
Capacitive divider ratio CR

Input range
1 : 1 ... 1 : 10
Resolution
110
IMPORTANT!
Max. operating voltage (rms)
1000 V
Capacitance values
1900 ... 10000 pF
Dimensions (L x W x H)
360 x 360 x 450 mm

(14.2 x 14,2 x 17.7 in)
Weight
Max. measurement voltage = max. permissible rated

voltage of compressed gas capacitor.
3/4
2000 pF 24 kg (52.8 lb)

4000 pF 27 kg (59.4 lb)
5000 pF 29 kg (63.8 lb)
10000 pF 35 kg (77.0 lb)
ORDER SPECIFICATION
OPTIONS
STANDARD SUPPLY
IEEE 488 interface
Standard voltage divider as per standard system type

series 4860, comprising:
Cable data-links for:
type 4861/1
Electronic device
Type 4861
- IEEE 488 interface, 4m
type 5993
Compressed gas capacitor*
series 3370 NK
- RS 232C interface, 3m
type 5991
Air capacitors
series 3330
- RS 232C interface
(fibre optic data-link)
type 5992
Adaptor box for direct connection,
no. 014235-00
no. 014107-00
Triax/coax adapter
for compressed gas capacitor
(for C/tan measurement)
no. 008140-72
Measuring cable, 10 m
Measuring cable, 1.5 m
no. 013685-00
Measuring cable, 0.5 m
no. 014108-00
Ground cable, 16 mm2, 10 m
no. 016351-00
Replacement of series 4850 electronic device by

type 4861
The connections are compatible with the existing unit.
Determine and set the capacity divider ratio.
Power cable
Power voltage
230 or 115 V,
50/60 Hz
IMPORTANT
(please specify with order)

Including RS 232C interface
Adaption and commissioning of the standard voltage

divider by HAEFELY HIPOTRONICS is essential to
ensure its required accuracy.
type 4861/2
*The compressed gas capacitor has to be ordered

separately.
4/4

4860 DS

Uploaded by

Copyright:

Available Formats

4860 DS

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4860 DS

Uploaded by

Copyright:

Available Formats

4860

Standard Electronic Voltage Dividers

The 4860 series (control unit and capacitive HV

Universal comparison standard for any transformer

Very accurate voltage divider ratio ( 50 ppm, 0.1

Max. measurement voltage is dependent only on rated

For voltages less than 1000 V the electronic device can

VOLTAGE DIVIDER ARRANGEMENT

2711/23) and many other manufacturers transformer

Direct replacement of earlier series 4850

Complete system is certifiable

A more cost-effective solution than inductive voltage

BASIC TEST SET-UP

Measurement circuit with capacitive divider for > 1 kV primary voltage

Legend for abbreviations used

ELECTRONIC STANDARD VOLTAGE DIVIDER

* range covered by any other type e.g. 4861/300

TYPE 4861 STANDARD VERSION

This version has up to two fixed voltage divider ratios

TYPE 4862 CUSTOMIZED VERSION

The user can set two ratios and change them

Storage and transport temperature

500 x 310 x 470 mm

Intrinsic error (electronic device)

ELECTRONIC SYSTEM TYPES 4861

Measurement signal frequency

20 ... 200 % U/UR

50 ppm 0.1 min

At rated operating conditions

100 ppm 0.2 min

Reference and rated operating conditions according to

Max. guard capacitance

With extended operating range

Max. output voltage Usec

Max. power output for U/UR = 100%

With extended frequency range

Max. output current for Usec 50 V

Max. load capacitance

With capacitive divider

Existing type 4850 electronic device replaced by type

SERIES 3370 GAS CAPACITORS (C1)

x1, x1/3, x1/3

Technical specification as in leaflets of 3370 and 3380.

Rated secondary voltage SV

x1, x1/3, x1/3

SERIES 3330 AIR CAPACITORS (C2)

Capacitive divider ratio CR

Max. operating voltage (rms)

1900 ... 10000 pF

360 x 360 x 450 mm

Max. measurement voltage = max. permissible rated

2000 pF 24 kg (52.8 lb)

IEEE 488 interface

Standard voltage divider as per standard system type

Cable data-links for:

- IEEE 488 interface, 4m

Compressed gas capacitor*

Adaptor box for direct connection,