Ans Ex
Ans Ex
Ans Ex
No:
STRESS ANALYSIS OF
Date :
PRESSURE VESSEL
AIM:
To determine the maximum deformation and Von Mises stress that occurs in a
pressure vessel with a thickness of 25 mm.
SOFTWARES USED:
ANSYS 13.0
M S Paint
ELEMENT TYPE:
Shell 181
MATERIAL PROPERTIES:
Youngs modulus
Poissons ratio
= 2e5 N/mm2
= 0.3
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> select Element type followed by ADD. Now select Shell and 3D 4
option.
In pre-processor>numbering control, merge the keypoints.
Now select pre-processor >OPERATE in Modeling followed by EXTRUDE option in
the sequence of-lines-About axis. Finally the model of the pressure vessel is ready for
meshing.
In pre-processor>meshing, select the mesh tool followed by set line and enters the
direction and enter the value as...........2 N/mm2........... and click OK.
In solution>solve >current LS and click OK. Now problem is solved.
In general post processor>Plot results>Contour plot> Nodal solution. In the dialogue
box Nodal solution-DOF solution-Displacement vector sum. Select display with
undeformed shape. Thus the deformed shape with undeformed shape is displayed.
In general post processor>Plot results>Contour plot> Nodal solution. In the dialogue
box Nodal solution-Stress-Von Mises. Select display with undeformed shape. Thus
(ii)
Maximum Stress
=.....................................................................
(iii)
Minimum Stress
=.....................................................................
Ex. No:
Date :
AIM:
To find out the temperature distribution of a rectangular fin when steady state heat
conduction takes place at a certain ambient temperature using ANSYS.
SOFTWARES USED:
ANSYS 13.0
M S Paint
ELEMENT TYPE:
Solid PLANE 55
MATERIAL PROPERTIES:
Conductivity Kxx
80w/mc
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Solid and Quad 4 node
kxx-80w/mc.
In pre-processor> Modeling> create>Areas>Rectangle>By Dimensions (10x2m).
In pre-processor> meshing> mesh tool-area-set and then select the area. Now in the
Temperature-On lines. Select the left side of the rectangular line apply ok. Also temp
value is 500C.
In Solution, apply loads in the following sequence- Define loads-Apply-ThermalTemperature-On lines. Select the other three side of the rectangular line apply ok.
The general post processor>vector plot > pre-defined and click Ok.
In PlotCtrls>style>Size and Shape-display of the element-ON.so the thickness of the
RESULT:
The temperature distribution is shown in the figure.
Ex. No:
Date :
AIM:
To find out the temperature distribution in the rectangular fin when the heat transfer is
steady and convective.
SOFTWARES USED:
ANSYS 13.0
M S Paint
ELEMENT TYPE:
Solid PLANE 55
MATERIAL PROPERTIES:
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Solid and Quad 4 node
Kxx-80w/mc.
In pre-processor> Modeling>create>Areas>Rectangle>By Dimensions (10x2m).
In pre-processor>meshing>mesh tool-area-set and then select the area. Now in the
In Solution, apply loads in the following sequence- Define loads-Apply-ThermalTemperature-On lines. Select the left side of the rectangular line apply ok. Also temp
value is 500C.
In Solution, apply loads in the following sequence- Define loads-Apply-Thermal-
Convective-On lines. Select the other three side of the rectangular line apply ok.
In the dialogue box enter the film coefficient as 10w/m 2C and bulk temperature as
80C.
In solution>solve>current LS and click OK. Now problem is solved.
In general post processor > read results > first set.
In general post processor>Plot results>Contour plot>Nodal solution. In the dialogue
box -DOF solution-Nodal Temperature. Select display with undeformed shape. Thus
RESULT:
The temperature distribution is shown in the figure.
Ex. No:
Date :
HEAT TRANSFER
ANALYSIS OF A 3-D CIRCULAR FIN
AIM:
To find out the temperature distribution of a 3D circular fin when the heat transfer is
steady and convective.
SOFTWARES USED:
ANSYS 13.0
M S Paint
Solid 90
MATERIAL PROPERTIES:
Conductivity Kxx
= 80w/cmc = 8w/mmc
Film coefficient h
= 10w/cm c = 0.1w/mm c
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor>Element type followed by ADD. Now select Solid and Brick 20
node 90.
In pre-processor>Material properties followed by Material model. Now select the
following sequence in order- Thermal-Conductivity-Isotropic. Enter the values of
Kxx-80w/mc.
In pre-processor>Modeling>create>Volumes>Cylinder>By Dimensions
Convective-On areas. Select the other side of the cylinder apply ok.
In the dialogue box enter the film coefficient as 0.1w/mm 2C and bulk temperature as
25C.
In solution>solve>current LS and click OK. Now problem is solved.
In general post processor > read results > first set.
In general post processor> Plot results>Contour plot>Nodal solution. In the dialogue
box -DOF solution-Nodal Temperature. Select display with undeformed shape. Thus
RESULT:
The temperature distribution is shown in figure.
Ex.No :
Date :
AIM:
To determine the maximum deformation at each joint and reaction in space truss.
SOFTWARE USED:
ANSYS 13.0
MS PAINT
ELEMENT USED:
LINK180
MATERIAL PROPERTIES:
Youngs modulus
Poissons ratio
= 2e5 N/mm2
= 0.3
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Link and 3D finit Stn
180 element.
In pre-processor> constant-add. Type 1 and specify real constant set number as 1 and
In pre-processor> meshing> mesh tool followed by Lines set and enters the No of
click OK.
In Solution, apply loads in the following sequence- Define loads-Apply-Structuralforce-On Nodes. Select the number in the truss 1and Select click OK. In the direction
(Z & Y).
In Solution, apply loads in the following sequence- Define loads-Apply-Structuralforce-On Nodes. Select the number in the truss 5 and Select click OK. In the direction
(Z & Y).
In solution>solve> current LS and click OK. Now problem is solved.
In general post processor>Plot results>Contour plot>Nodal solution. In the dialogue
box, DOF solution-Displacement vector sum. Select display with undeformed shape.
RESULT:
The result was obtained successfully with help of ANSYS software
Maximum Deformation
= ----------------------
Reaction at
NODE
FX
FY
FZ
2
3
4
Ex. No:
Date :
AIM:
To determine the maximum deformation and axial stress that occurs when a given
horizontal truss is loaded in y-direction.
SOFTWARE USED:
ANSYS 13.0
MS PAINT
ELEMENT USED:
LINK180
MATERIAL PROPERTIES:
Youngs modulus
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Link and 3D finit Stn
180 element.
In pre-processor> Real constant-add. Type 1 and specify real constant set number as 1
click OK.
In Solution, apply loads in the following sequence- Define loads-Apply-Structuralforce-On Nodes. Select the number in the truss 4&5 and Select click OK. In the
direction Y.
In solution>solve> current LS and click OK. Now problem is solved.
In general post processor> Plot results>Contour plot>Nodal solution. In the dialogue
box, DOF solution-Displacement vector sum. Select display with undeformed shape.
RESULT:
The result was obtained successfully with help of ANSYS software
Maximum Deformation
=-----------------------
Maximum Stress
=------------------------
Minimum Stress
=-----------------------
Ex. No:
Date :
AIM:
To determine the maximum deflection, axial stress and reaction force that occurs when a
given planar truss is loaded in x & y-directions.
SOFTWARE USED:
ANSYS 13.0
MS PAINT
ELEMENT USED:
LINK180
MATERIAL PROPERTIES:
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Link and 3D finit Stn
180 element.
In pre-processor> Real constant-add. Type 1-4 and specify real constant set number as
1-4 and Cross section areas are (16000, 8000, 1500 & 10000mm2).
In pre-processor>Material properties followed by Material model. Now select the
following sequence in order- Structural-Linear-Elastic-Isotropic. Enter the values of
click OK.
In Solution, apply loads in the following sequence- Define loads-Apply-Structuralforce-On Nodes. Select the number in the truss 3 and Select click OK. In the
direction X.
In Solution, apply loads in the following sequence- Define loads-Apply-Structuralforce-On Nodes. Select the number in the truss 4 and Select click OK. In the
direction Y.
In solution>solve> current LS and click OK. Now problem is solved.
In general post processor> Plot results>Contour plot>Nodal solution. In the dialogue
box, DOF solution-Displacement vector sum. Select display with undeformed shape.
Thus the deformed shape with undeformed shape is displayed.
In general post processor > define table > add table and notify the axial stress (Sxx)
and plot.
In general postprocessor > list result > reaction solution.
Take the image of the result using the image capture option.
RESULT:
The result was obtained successfully with help of ANSYS software
Maximum Deformation
=-----------------------
=------------------------
=-----------------------
Reaction at NODE
FX
FY
FZ
1
6
Ex. No:
Date :
AIM:
To determine the maximum displacement reaction forces, member forces and stress that
occurs when a temperature is applied to truss.
SOFTWARE USED:
ANSYS 13.0
MS PAINT
ELEMENT USED:
LINK180
MATERIAL PROPERTIES:
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> Element type followed by ADD. Now select Link and 3D finit Stn
180 element.
In pre-processor> Real constant-add. Type 1 and specify real constant set number as 1
In
pre-processor>Modeling>Create>lines>lines>straight
line
connects
all
the
In pre-processor> meshing> mesh tool followed by Lines set and enters the No of
click OK.
In Solution, apply loads in the following sequence- Define loads-Apply-Thermaltemperature-On lines (120c). Select the members AC and CD truss and Select click
OK.
In solution>solve>current LS and click OK. Now problem is solved.
In general post processor> Plot results>Contour plot>Nodal solution. In the dialogue
box, DOF solution-Displacement vector sum. Select display with undeformed shape.
RESULT:
The result was obtained successfully with help of ANSYS software
Maximum Deformation
Reaction at NODE
=----------------------FX
FY
FZ
1
2
4
Ex. No:
Date
PRESSURE
AIM:
To determine the axial stress hoop stress that occurs when a given the cylinder wall and
plot it in window.
SOFTWARE USED:
ANSYS 13.0
MS PAINT
ELEMENT USED:
SOLID183
MATERIAL PROPERTIES:
Youngs modulus
Poissons ratio
= 2e5 N/mm2
= 0.3
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
In pre-processor> Element type followed by ADD. Now select Solid and 8 node 183
the dimensions.
In pre-processor> Modeling>Create>lines>lines>straight line. connects all the keypoints as
per the drawing.
selects expansions.
In solution>solve>current LS and click OK. Now problem is solved.
In general post processor>Plot results>Contour plot>Nodal solution.In the dialogue
box, Stress-Y component of stress & Z component of stress. Thus the deformed shape
RESULT:
The result was obtained successfully with help of ANSYS software
Maximum Axial Stress
=------------------------
=-----------------------
Ex. No:
Date :
AIM:
To determine the maximum radial and axial deflection that occurs in a Belleville
spring with a thickness of 2.5 mm.
SOFTWARES USED:
ANSYS 13.0
M S Paint.
ELEMENT TYPE:
Shell 208
MATERIAL PROPERTIES:
Youngs modulus
Poissons ratio
= 2.07e5 N/mm2
= 0.3
PROCEDURE:
Open a new ANSYS file by using ANSYS Product Launcher. Select the directory file
click OK.
In pre-processor> select Element type followed by ADD. Now select Shell and
click OK.
In Solution, apply loads in the following sequence- Define loads-Apply-StructuralForce/Moment-On nodes. Select node on the top of the line. Select Y-direction and
undeformed shape. Thus the deformed shape with undeformed shape is displayed.
In PlotCtrls>style>Size and Shape-display of the element-ON.so the thickness of the
=....................................................................
(ii)
=.....................................................................
(iii)
Maximum deformation
=...