Modular Azkoyen

Modular X
Technical Information Modular X-DSP

Revision 04/2011
INTRODUCTION. ...................................................................................................................... 5
1.1
CONCEPT OF MODULARITY. .......................................................................................... 5
DESCRIPTION OF COMPONENTS ......................................................................................... 7

2.1
COVER OF THE VALIDATOR (1)..................................................................................... 7
2.2
SENSOR MODULE (2). ....................................................................................................... 8
2.2.1
Circuit board and connectors ......................................................................................... 9
2.2.2
Inductive sensors ............................................................................................................ 9
2.2.3
Acoustic sensor ............................................................................................................ 10
2.2.4
Diameter sensor............................................................................................................ 10
2.2.5
Rocker. ......................................................................................................................... 10
2.2.6
String detector. ............................................................................................................. 11
2.2.7
Refund lever (3). .......................................................................................................... 11
2.3
COMMUNICATION BUS BETWEEN SENSOR AND OUTPUT MODULES (4). ....... 11
2.4
OUTPUT MODULE (6) .................................................................................................... 11
2.4.1
Circuit board and connectors (5):................................................................................. 12
2.4.2
Acceptance gate (7). ..................................................................................................... 12
2.4.3
Anchorage pivots (8). ................................................................................................... 12
TECHNICAL CHARACTERISTICS........................................................................................ 12
3.1
Range of coins identified. .................................................................................................... 12
3.2
Coin identification capacity................................................................................................. 13
3.3
Power and current ranges. ................................................................................................... 13
3.4
Connections accessible to the user and pin out. .................................................................. 13
3.4.1
Connector J1 (10 pins) for communication with the machine. .................................... 14
3.4.2
Connector J2 (4 pins) for communication with Azkoyen tools. .................................. 14

Revision 04/2011
3.5
Configuration Switches. ...................................................................................................... 15
3.6
Dimensions. ......................................................................................................................... 16
OPERATING CONDITIONS AND NORMS .......................................................................... 16
CLEANING AND MAINTENANCE ....................................................................................... 17
QUALITY PARAMETERS. ..................................................................................................... 18
6.1
USEFUL LIFE. ................................................................................................................... 18
6.2
MTBF. Mean time between failures.................................................................................... 18
6.3
MCBF. Mean cycles between failures. ............................................................................... 18
ACCESSORIES. ........................................................................................................................ 18
7.1
FUNNELS. .......................................................................................................................... 18
7.2
SORTERS: .......................................................................................................................... 19
AZKOYEN TOOLS. ................................................................................................................. 19

8.1
HEUS................................................................................................................................... 19
8.2
TL20. ................................................................................................................................... 20
8.3
Simulation / Verification tool: IS21-A ................................................................................ 21

Revision 04/2011
Figures:
Figure 1. Modularity ....................................................................................................... 5
Figure 2. Module D2S ..................................................................................................... 6
Figure 3. Module D4S ..................................................................................................... 6
Figure 4.Components ..................................................................................................... 7
Figure 5. Label .............................................................................................................. 7
Figure 6. Sensor module ................................................................................................ 8
Figure 7. Removal of the sensor module ........................................................................... 8
Figure 8. Connectors in output module. .......................................................................... 12
Figure 9. Connectors accessible to the user. ................................................................... 13
Figure 10. Dimensions ................................................................................................. 16
Figure 11. Funnels. ...................................................................................................... 18
Figure 12. Azkoyen Sorters. .......................................................................................... 19
Figure 13. HeUs .......................................................................................................... 20
Figure 14. TL20 ........................................................................................................... 20
Figure 15. IS21-A ........................................................................................................ 21

Revision 04/2011
1 INTRODUCTION.
Coin validators are devices, installed inside the machines, with the task of identifying and
validating coins introduced into the machine. They are used in various sectors such as slot
machines, vending machines, gambling machines, cigarette vending machines and so on.
This manual contains technical information for the coin validators in the X-DSP range that are
part of the Modular DSP series. The points covered in this document are therefore valid for the
following models of validators:
X6-D2S
X6-D4S
This manual will use general term X-DSP, which shall refer to any of the aforementioned
validators.
For full information on the operation of these validators, this manual must be complemented
with the corresponding manual "Communication protocol" of the product available on the
Azkoyen website: http://sat.azkoyen.com.
1.1 CONCEPT OF MODULARITY.

The concept of modularity, a principle feature of the current range of Azkoyen validators, is
characterized by a marked distinction between the part of the validator for reading the
characteristics of the coin (SENSOR MODULE) and the part intended for communication with
the machine (OUTPUT MODULE).
Figure 1. Modularity

Revision 04/2011
Depending on the type of sensorization used (see paragraph 2.2) we have two versions of
validators:
X6-D2S
It is the standard validator used in most applications. It has 3 pairs of optical
sensors, 1 acoustic sensor and 1 pair of inductive sensors.
Figure 2. Module D2S
X6-D4S
It is the validator used in applications that, due to the metallic characteristics of the
coins, require extra sensorization. It includes 3 pairs of optical sensors, 1 acoustic
sensor and 2 pairs of inductive sensors.
Figure 3. Module D4S

Revision 04/2011
2 DESCRIPTION OF COMPONENTS
Figure 4.Components
2.1 COVER OF THE VALIDATOR (1).

It is designed to protect the various electronic components within the validator. It has
information stickers with the characteristics of the validator associated with the corresponding
references:
1- DESCRIPTION OF THE VALIDATOR
2- COUNTRY
PROGRAMMING
OF
THE
VALIDATOR
3- CODE OF THE VALIDATOR
4- COINS AND CODES PROGRAMMED IN
THE VALIDATOR
5- POWER AND VOLTAGE.
6- PIN TO CONNECT THE POWER
Figure 5. Label

Revision 04/2011
2.2 SENSOR MODULE (2).

This component has most of the measurement and control systems that the validator uses to
determine whether the coin should be accepted or rejected and the value of the coin if it is
accepted. It is a common element to all models of validators that have the same sensorization
(option D2S or option D4S).
Figure 6. Sensor module

To remove it from the output module you need to remove the 2 screws in the holes that are
indicated by arrows in the following image:
Figure 7. Removal of the sensor module

The main elements on the sensor module are:

Revision 04/2011
2.2.1 Circuit board and connectors
JP100: Bus for communicating with

output module.
JP101: Serial port. For use in factory
JP102: Programming connector.
Available for connecting programming
tools.
2.2.2 Inductive sensors
The
validator
has,
depending
on
model,
between 2 and 4 inductive sensors to obtain

coin
parameters
related
to
its
alloy
and
thickness. The design enables the reading of

coins
manufactured
with
bimetallic
and/or
multilayer technologies.

Revision 04/2011
2.2.3
Acoustic sensor
The acoustic sensor is located at the bottom

of the entry module and this device captures
the sound emitted by the coin when it passes
against the metal cylinder on its way through
the validator. The parameters collected by the
sensor are very important in the process of
acceptance or rejection of the coin.
2.2.4 Diameter sensor
3 Pairs of infrared light sensors can be used to

obtain parameters related to the diameter of
the coin.
2.2.5 Rocker.
It stabilizes the speed of the coin to

ensure a constant entry speed of the
coin as is goes through the validator
so that measurements taken from the
coin are more precise.

Revision 04/2011
10
2.2.6 String detector.

A "string detector" system is inside the sensor module, an electro-mechanical device that is
intended to foil any attempt of fraud using the method of attaching a string to a coin. The
operation relies on a barrier of infrared light that passes through the hole of the rocker. The
infrared light beam is interrupted when the rocker is moved by the by the presence of the
string. The validator understands this signal as an attempt of fraud and inhibits the coin.
2.2.7 Refund lever (3).

On pressing this lever, the validator door opens and thus eliminates possible coin jams
produced within the validator.
2.3 COMMUNICATION BUS BETWEEN SENSOR AND OUTPUT MODULES (4).

It provides communication between the output module and the sensor module. To disconnect
it, remove it from the connector on the sensor module.
2.4 OUTPUT MODULE (6)

It manages the communication between the validator and the machine on which it is installed.
The circuit board has a "flash memory" which can be reprogrammed with the tools and
procedures described in the Technical Manual of the "User Tool" (HeUs)
Its principle elements are:

Revision 04/2011
11
2.4.1 Circuit board and connectors (5):

JP201:
Connector
for
communication with the machine.

JP202:
Communication bus with the
sensor module.
JP203:
NOT USEB BY USER
JP204: Acceptance gate connector.

JP205:
Connector
for
tokens
programmation
Figure 8. Connectors in output module.

2.4.2 Acceptance gate (7).
When the validator accepts a coin, this electromagnetic shutter is activated allowing the coin to
go through the accepted coin channel.
The solenoid uses 12 Vdc.

2.4.3 Anchorage pivots (8).
Anchorage pivots to hold the validator inside the machine where necessary, pivots are 4.5 mm
in and 5 mm in length
3 TECHNICAL CHARACTERISTICS
3.1 Range of coins identified.
The physical dimensions of the coins supported by the validator are:
Revision 04/2011
12
Minimum
Maximum
Diameter
16.25 mm
32.5 mm
Thickness
1.2 mm
3.3 mm
The data displayed in the table above are valid for circular coins. To confirm the proper
functioning of this range of validators for other coins, please contact the factory.
3.2 Coin identification capacity.

The X-DSP range of validators can support 32 different coin types.
Two of these 32 coins (tokens) can be programmed by the user in the field using the
connector JP205 and some jumpers to connect the pins. For more information consult the
"Parallel Protocol" manual of this product.
3.3 Power and current ranges.
VALUES
Power supply
12 V (10%)
Current during coin validation

Current during coin acceptance
50 mA
Average 150 mA
3.4 Connections accessible to the user and pin out.
Figure 9. Connectors accessible to the user.

Revision 04/2011
13
3.4.1 Connector J1 (10 pins) for communication with the machine.

It is the main connector for communication with the machine. The
validator power supply is through pins 1 (Vcc) and 2 (GND) for this
connector.
The function of each of the pins is shown in next table
Connector J1 on the Output module
Pins
Function
Notes
Pin 1
+ 12 Vcc
Pin 2
GND
Pin 3
Output 7
Open collector, transistor NPN.
Pin 4
Output 1
Pin 5
Output 6
Pin 6
Inhibition
Pin 7
Output 3
Pin 8
Output 2
Pin 9
Output 4
Pin 10
Output 5
Minimum+ 10 Vcc; Maximum +15 Vcc
Table 1. Connector J1 (2x5)

3.4.2 Connector J2 (4 pins) for communication with Azkoyen tools.
This 4-pin connector is used to connect the Azkoyen validator tools software (HEUS) and
hardware interface (TL20).
Section 7 of this manual contains details the procedure to follow for the connection of the
validator tools.
The connector pinout is detailed in the following table

Revision 04/2011
14
Connector J2. AZKOYEN TOOLS

Pins
Function
Pin 1
Rx
Pin 2
GND
Pin 3
Tx
Pin 4
Vin
Notes
Reception of data
Transmission of data
Table 1. Pinout of tool connector.

The 12/24 V power supply will not power the validator through this
connector, it will always be necessary to maintain the validator powered
through the J1 connector.
3.5 Configuration Switches.

X6 validator has 4 dipswitches to be used as follows:
Switch 1.
Select between tokens to be programmed:token 1 or token 2.
Switches 2,3 and 4
Enable or disable coins.
Activate Narrow bands. (more restricted admission of coins)
It is necessary to check technical datasheets for particular validator codes, in order to get the
specific functionality of switches.

Revision 04/2011
15
3.6 Dimensions.
Figure 10. Dimensions

The validator weighs approximately 200 grams.
4 OPERATING CONDITIONS AND NORMS

The optimal operation of this equipment is achieved with the following requirements:
Install the validator inside the machine with a maximum slope of any of its axis of 3.
Temperatures:
Storage: from -25 to +70C.
Operation: from +5 to +55C.
Humidity: maximum 95% (relative humidity without condensation)
Never connect or disconnect the validator with the machine switched on.

Revision 04/2011
16
Norms.
EN50081-1. Generic emission norm.
EN50022: radiated emission. Measurement of disturbances in field.
EN50022: conducted emission. Measurement of disturbances in power supply.
EN50082-1: Generic immunity norm.
IEC801-2: electrostatic discharges. Extent of the immunity to electrostatic
discharges.
IEC801-3: radiated immunity. Extent of the immunity to electric fields.
IEC801-4: transient flashes / spikes. Extent of the immunity to transient

flashes / spikes.
EN60335-1 (94-95). Safety of appliances
CE
The manufacturer is not responsible of damage to the validators if the

specifications above are not respected.
5 CLEANING AND MAINTENANCE

Maintenance on the Validator is determined by the quantity of dirt the coins leave and that
obstruct its elements.
For cleaning, follow the following guidelines:
Disconnect the power supply - connector J1-
Clean soiled areas with a brush with vegetable fibres (never metallic) impregnated
with alcohol. Clean with more detail:
Coin channel
Metal cylinder
The optic sensor holes and photocells on the string detector
The string detector system
WARNING:
Revision 04/2011
17
Never use products containing benzenes. These compounds produce a rapid

deterioration of the plastics causing irreparable damage.
The validator must never be immersed in liquid.
6 QUALITY PARAMETERS.
6.1 USEFUL LIFE.
The useful life of the validator is 1 million services.
6.2 MTBF. Mean time between failures.

Under normal operating conditions of work (excluding manipulation, fraudulent coins and
working outside of the parameters referred to in section 4), AC-DSP validators have an MTBF
value of 1.3 validators for every 100 units per year.
6.3 MCBF. Mean cycles between failures.

Under normal operating conditions of work (excluding manipulation, fraudulent coins and
working outside of the parameters referred to in section 4), AC-DSP validators have an MCBF
value of 840,000 coins.
7 ACCESSORIES.
7.1 FUNNELS.
There are three models available for the validators of this range:
Long
Medium
Short
41149571
41145041
41160471
Figure 11. Funnels.

Revision 04/2011
18
7.2 SORTERS:
The range of validators can work with standard models (3-5 way) of Azkoyen sorters.
Modular Sorter
Sorter with front plate
Figure 12. Azkoyen Sorters.
Azkoyen validators cannot be used with sorters of other manufactures.

For more information, consult the specific manuals of sorters available on
the Azkoyen website http://sat.azkoyen.com.
8 AZKOYEN TOOLS.
8.1 HEUS.
The HEUS (user tool) software has two basic applications in the management of AC-DSP
validators.

Revision 04/2011
19
Figure 13. HeUs
A tool for editing and modification of settings. It allows you to modify each one of the
characteristic values in this range of validators detailed in paragraph 4.2.
A tool for uploading files for configuration and programming. You can download files
directly from your PC with the validator tool HEUS.
Communication between PC (HEUS) and the validator is done via cable right directly from the
RS232 port of the PC to the 4-way connector J2 on the validator.
To know the details of the implementation and management of the HEUS, consult the specific
manual available on the Azkoyen website http://sat.azkoyen.com.
8.2 TL20.
The TL20 is a hardware tool that is used to upload files for programming and configuration in
AC-DSP validators.
Figure 14. TL20

Revision 04/2011
20
The TL20 programmer will connect to the validator on the 4-way connector on the validator
module J2.
To know the details of the implementation and management of the TL20, consult the specific
8.3 Simulation / Verification tool: IS21-A
The IS21-A interface allows us to verify the proper functioning of the validator as it simulates
the behaviour of a machine.
There are numerous configuration switches as well as a Display to setup different working
modes in the validator.
Figure 15. IS21-A

To know the details of the implementation and management of the IS21-A, consult the specific

Revision 04/2011
21

Modular Azkoyen

Uploaded by

Copyright:

Available Formats

Modular Azkoyen

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Modular Azkoyen

Uploaded by

Copyright:

Available Formats

Modular X

Technical Information Modular X-DSP

CONCEPT OF MODULARITY. .......................................................................................... 5

DESCRIPTION OF COMPONENTS ......................................................................................... 7

COVER OF THE VALIDATOR (1)..................................................................................... 7

SENSOR MODULE (2). ....................................................................................................... 8

Circuit board and connectors ......................................................................................... 9

Inductive sensors ............................................................................................................ 9

Acoustic sensor ............................................................................................................ 10

String detector. ............................................................................................................. 11

Refund lever (3). .......................................................................................................... 11

COMMUNICATION BUS BETWEEN SENSOR AND OUTPUT MODULES (4). ....... 11

OUTPUT MODULE (6) .................................................................................................... 11

Circuit board and connectors (5):................................................................................. 12

Acceptance gate (7). ..................................................................................................... 12

Anchorage pivots (8). ................................................................................................... 12

Range of coins identified. .................................................................................................... 12

Coin identification capacity................................................................................................. 13

Power and current ranges. ................................................................................................... 13

Connections accessible to the user and pin out. .................................................................. 13

Connector J1 (10 pins) for communication with the machine. .................................... 14

Connector J2 (4 pins) for communication with Azkoyen tools. .................................. 14

Technical Information Modular X-DSP

Configuration Switches. ...................................................................................................... 15

OPERATING CONDITIONS AND NORMS .......................................................................... 16

CLEANING AND MAINTENANCE ....................................................................................... 17

QUALITY PARAMETERS. ..................................................................................................... 18

USEFUL LIFE. ................................................................................................................... 18

MTBF. Mean time between failures.................................................................................... 18

MCBF. Mean cycles between failures. ............................................................................... 18

AZKOYEN TOOLS. ................................................................................................................. 19

Simulation / Verification tool: IS21-A ................................................................................ 21

Technical Information Modular X-DSP

Technical Information Modular X-DSP

1.1 CONCEPT OF MODULARITY.

Technical Information Modular X-DSP

Figure 2. Module D2S

Figure 3. Module D4S

Technical Information Modular X-DSP

2.1 COVER OF THE VALIDATOR (1).

Technical Information Modular X-DSP

2.2 SENSOR MODULE (2).

Figure 6. Sensor module

Figure 7. Removal of the sensor module

Technical Information Modular X-DSP

2.2.1 Circuit board and connectors

JP100: Bus for communicating with

2.2.2 Inductive sensors

between 2 and 4 inductive sensors to obtain

thickness. The design enables the reading of

Technical Information Modular X-DSP

The acoustic sensor is located at the bottom

2.2.4 Diameter sensor

3 Pairs of infrared light sensors can be used to

It stabilizes the speed of the coin to

Technical Information Modular X-DSP

2.2.6 String detector.

2.2.7 Refund lever (3).

2.3 COMMUNICATION BUS BETWEEN SENSOR AND OUTPUT MODULES (4).