Service Details Man BW PDF

Service Letter SL09-509/SBJ
Action code:
WHEN CONVENIENT
Guiding Overhaul Intervals

Updated Tables
SL09-509/SBJ
April 2009
Concerns
Owners and operators of MAN B&W
two-stroke diesel engines.
Type: ME/ME-C, ME-B and MC/MC-C
Dear Sirs
Based on the latest service experience and experience with Condition
Based Overhaul (CBO), we are pleased to issue a revised version of
Guiding Overhaul Intervals tables. The guiding overhaul intervals apply
to both electronically controlled engines (ME types) and mechanically,
controlled engines (MC types).
Please note that the intervals in the lists apply only to engines with socalled high topland pistons. High topland pistons are pistons where the
topland is significantly higher than the ringland.
For engines with high topland pistons, overhauls can normally be extended even further than described in the tables, typically to more than
32,000 hours. The means to obtain and document this are described in
SL07-483/HRR.
Please direct any inquiries and questions regarding tables or conditionbased overhaul to our Operation Department at leo@mandiesel.com or
to our Service Department at PrimeServ-cph@mandiesel.com.
Yours faithfully
Mikael C Jensen
Stig B Jakobsen
Vice President, Engineering
Senior Manager, Engineering
Head office (& postal address)

MAN Diesel
Teglholmsgade 41
2450 Copenhagen SV
Denmark
Phone: +45 33 85 11 00
Fax:
+45 33 85 10 30
mandiesel-cph@mandiesel.com
www.mandiesel.com
Overhaul of cylinder unit on large bore

engine
PrimeServ
Production
Forwarding & Receiving
MAN Diesel
Teglholmsgade 41
2450 Copenhagen SV
Denmark
Phone: +45 33 85 11 00
Fax: +45 33 85 10 49
PrimeServ-cph@mandiesel.com
Teglholmsgade 35
2450 Copenhagen SV
Denmark
Phone: +45 33 85 11 00
Fax: +45 33 85 10 17
manufacturing-dk@mandiesel.com
Teglholmsgade 35
2450 Copenhagen SV
Denmark
Phone: +45 33 85 11 00
Fax:
+45 33 85 10 16
Branch of MAN Diesel SE, Germany

CVR No.: 31611792
Head office: Teglholmsgade 41
2450 Copenhagen SV, Denmark
German Reg.No.: HRB 22056
Amtsgericht Augsburg
MAN Diesel a member of the MAN Group
ME-B engines
Guiding overhaul intervals and expected service life
Component
Overhaul interval (hours)
Expected service life (hours) Remarks
Cylinder liner
Bore sizes
60-50
46-35
16,000
12,000
Bore sizes
60-46
40-35
60,000
50,000
Bore sizes
60-50
46-35
16,000
12,000
Bore sizes
60-35
16,000
Piston rings
Piston crown
Stuffing box
Exhaust valve spindle

and bottom piece (cage)
Bore sizes
60-50
46-35
Bore sizes
60-46
40-35
60,000
50,000
Bore sizes
16,000 60-50
12,000 46-35
Check lamellas
32,000
24,000
Renew lamellas
16,000
12,000
Bore sizes
60-50
46-35
Inspection of seat and air spring:

Bore sizes
60-35
First inspection 1)
Bore sizes
50-35
Subsequent inspections 2)
Main hydraulic pump
6,000
Bore sizes
50-35
DuraSpindle exhaust valve
Bore size
60
DuraSpindle or
Nimonic exhaust valve
50,000
Usually only light grinding of seats is
required at subsequent inspections.
100,000
Bore size
60
32,000
To be obtained for DuraSpindle and

Nimonic valve with reconditioning of
seat and possible re-welding of disk
underside
32,000
Engine lifetime
Pressure test at every 2nd piston

overhaul, recondition/rechrome when
required (typically every 24-32,000
hours). Piston crown can be reconditioned by welding-up twice.
Normally, HVOF coated stems need

no reconditioning.
16,000
Proportional valve for

main hydraulic pump
Check the overall cylinder condition

through the scavenge ports at least
once a month.
1) Condition check
Inspection of air spring according
to instruction manual. Two or three
valves to be inspected.
2) Subsequent inspection
Condition check + possible complete
overhaul. Max burn off rate of spindle
disc underside to be estimated and
calculated for lifetime of spindle. All
Check and replace hydrostatic bearings at overhaul. Check and replace
cylinder set and piston if required.
20,000
Replace valve after 20,000 hours
Pressure relief valve for

main hydraulic pumps
40,000
Engine lifetime
Replace sealings at overhaul
Exhaust valve actuator
32,000
Engine lifetime
Replace static sealing rings at overhaul.
ELFI valve
32,000
64,000
Fuel valve
8,000
- depending on fuel quality
Valve nozzle
Spindle guide
16,000 Check and replace if required

16,000
Fuel oil pressure booster
32,000
- based on engine observations
64,000
Replace or recondition
Check and replace if required
Change piston rings on hydraulic piston and suction valve at overhaul.
Guiding Overhaul Intervals. Page of 7 pages
ME-B engines
Component
Cylinder cover

96,000
Check for burned grooves at fuel valve

nozzle holes. Weld-up if required, up
to 2-3 times during service life.
Starting valve
12,000
Engine lifetime
Cylinder lubricator
24,000
Engine lifetime
Crosshead bearings
Main bearings
Crank bearings
Thrust bearings
Check clearances and crankshaft

deflection: once a year.
Check bearing edges by wire gauges:
once a year
Tie rods including

bracing screws
Tighten rods and screws:

once a year
Engine lifetime
Holding down bolts
Tighten: once a year
Engine lifetime
Turbocharger
According to manufacturers
recommendations.
recommendations.
recommendations.
Air cooler(s)
Cleaning:
based on engine observations

45,000
or according to manufacturers recommendations.
Clean before differential pressure has

increased 50% compared to sea trial
value.
Flaps and butterfly

valves in scavenge air
receiver
Check movement at every

scavenge port inspection.
Engine lifetime
Various fuel and

lubricating oil filters
Cleaning:
Lubricating oil bottom

tank
Cleaning:
Chains
3,000-4,000
Retighten chains:

- every six months
Accumulators on
HPS and HCU
N2 pressure
Rubber membranes:
Engine lifetime
Check timing and adjustment

64,000
96,000
96,000
96,000
32,000
3,000
32,000
Hydraulic hoses
Do not open bearings unless

bearing material fragments fall out or
other bearing inspection measures
indicate so.
Typically done at 5 years docking

96,000
New or overhauled chains to be

checked/retightened after 500, 1,500
hours.
Replace membranes after 5 years
32,000
Replace after 5 years
Angle encoder
Visual inspection:
6,000
64,000
Replace if failing
Marker sensor
Visual inspection:
6,000
64,000
Replace if failing
MPC, MOP A, MOP B
Visual inspection:
6,000
64,000
Replace if failing
Cables
Visual inspection:
6,000
96,000
Replace if failing
ME/ME-C engines
Component
Cylinder liner
Bore sizes
98-80
24,000
Bore sizes
70-50
16,000
Bore sizes
98-90
80-65
60-50
80,000
70,000
60,000
Bore sizes
98-80
24,000
Bore sizes
98-80
24,000
Bore sizes
70-50
16,000
Bore sizes
70-50
16,000
Bore sizes
98-90
24,000
Bore sizes
70-50
16,000
Bore sizes
98-90
80-65
60-50
80,000
70,000
60,000
Piston rings
Piston crown
Stuffing box

Bore sizes
98-80
70-50
Bore sizes
98-50
First inspection 1)
Bore sizes
98-50
6,000

32,000
32,000
Renew lamellas
24,000
16,000
Check lamellas

once a month.
Bore sizes
98-60

no reconditioning.
100,000
To be obtained for Nimonic valve with

reconditioning of seat and possible
re-welding of disk underside
32,000

1) Condition check
2) Subseq. Inspection
calculated for lifetime of spindle.
All valves to be inspected.
Main hydraulic pump
32,000
Proportional valve for

main hydraulic pump
Engine lifetime
Check and replace hydrostatic bearings at overhaul. Check and replace

cylinder set and piston if required.
20,000
Replace valve after 20,000 hours
Pressure relief valve for

main hydraulic pumps
40,000
Engine lifetime
Replace sealings at overhaul
Exhaust valve actuator
32,000
Engine lifetime
Replace static sealing rings at overhaul.
FIVA valve
32,000
64,000
Fuel valve
8,000
Valve nozzle
Spindle guide

16,000
Fuel oil pressure booster
32,000
64,000
Replace or recondition
Check and replace if required
Change piston rings on hydraulic piston and suction valve at overhaul.
ME/ME-C engines
Component
Cylinder cover

96,000

Starting valve
12,000
Engine lifetime
Cylinder lubricator
24,000
Engine lifetime
Crosshead bearings
Main bearings
Crank bearings
Thrust bearings

once a year
Tie rods including

bracing screws

once a year
Engine lifetime
Holding down bolts
Engine lifetime
Turbocharger
recommendations.
recommendations.
recommendations.
Air cooler(s)
Cleaning:

45,000
or according to manufacturers recommendations
Clean before differential pressure has

increased 50% compared to sea trial
value.
Flaps and butterfly

receiver
Check movement at every

scavenge port inspection
Engine lifetime
Various fuel and

lubricating oil filters
Cleaning:

tank
Cleaning:
Chains
3,000-4,000
Retighten chains:

- every six months
96,000
Gear wheel drive for

hydraulic pumps
First inspection:
Subsequent inspections:
Gear wheel: Engine lifetime

Gear wheel bearings:
96,000
Accumulators on
HPS and HCU
N2 pressure:
Rubber membranes:
Check timing and adjustment

64,000
96,000
96,000
96,000
32,000
500
6,000
3,000
32,000
Hydraulic hoses

indicate so.
Engine lifetime

hours.
Replace membranes after 5 years
32,000
Replace after 5 years
MPC, MOP A, MOP B
Visual inspection:
6,000
64,000
Replace if failing
CCU and ACU amplifiers
Visual inspection:
6,000
64,000
Replace if failing
LVDT and LDI hydraulic

pump amplifiers
Visual inspection:
6,000
64,000
Replace if failing
Fuel booster sensor
Visual inspection:
6,000
64,000
Replace if failing
Exhaust valve sensor
Visual inspection:
6,000
64,000
Replace if failing
Angle encoder
Visual inspection:
6,000
64,000
Replace if failing
Marker sensor
Visual inspection:
6,000
64,000
Replace if failing
Cables
Visual inspection:
6,000
96,000
MC/MC-C engines
Component
Cylinder liner
Bore sizes
98-50
46-26
16,000
12,000
Bore sizes
98-90
80-70
60-50
46-35
26
80,000
70,000
60,000
50,000
40,000
Bore sizes
98-50
46-26
16,000
12,000
Bore sizes
98-50
46-26
16,000
12,000
Piston rings
Piston crown
Stuffing box

Bore sizes
98-50
46-26
16,000
12,000
Bore sizes
98-50
46-26
16,000
12,000
Check lamellas

Bore sizes
98-35
First inspection 1)
Bore sizes
50-35
6,000
Bore sizes
98-90
80-70
60-50
46-35
26
Bore sizes
98-50
46-26
80,000
70,000
60,000
50,000
40,000

once a month.

32,000
24,000
Renew lamellas
Bore sizes
50-35
DuraSpindle exhaust valve
Bore size
60
DuraSpindle or

no reconditioning.
50,000
100,000
16,000
1) Condition check
Bore sizes
98-60
32,000
To be obtained for DuraSpindle and

Nimonic valve with reconditioning of
seat and possible re-welding of disk
underside.
Actuator gear
Hydraulic system
32,000
64,000
Fuel valve
8,000
Valve nozzle
Spindle guide

16,000
Fuel pump plunger and

barrel, suction valve,
puncture valve and
shock absorber
16,000
Renew or recondition:
40,000
Change sealing rings on barrel,

plunger, puncture valve and suction
valve.
96,000

8,000
For suction valve and puncture valve
Cylinder cover
Starting valve, safety

valve and indicator cock
2) Subsequent inspection
calculated for lifetime of spindle. All
12,000
Engine lifetime
MC/MC-C engines
Component
Alpha Lubricator
Check/ Refill accumulators

Overhaul lubricators
Engine lifetime
Crosshead bearings
Main bearings
Crank bearings
Thrust bearings

once a year
Roller guide for fuel

pump and exhaust valve
Check condition in situ:
Engine lifetime
Chains
Tighten chains:

Chain wheels and rubber guide bars
Visual inspection:
3,000-4,000
Reversing and regulating gear
Check moving parts:

3,000-4,000
Tie rods including bracing screws

once a year
Engine lifetime
Holding down bolts
Engine lifetime
Turbocharger
recommendations.
recommendations.
Air cooler(s)
Cleaning:
Flaps and butterfly

receiver
Check movement at every scavenge

port inspection.
Engine lifetime.
Various fuel and lubricating oil filters.

Camshaft filters and
TCS filters, if any
Cleaning:

tank
Cleaning:
8,000
32,000
1,500
3,000-4,000
- every six months
64,000
96,000
96,000
96,000
Check running surfaces and free rotation of roller.
96,000

hours.
Chain wheels:
Guide bars:
96,000
32,000
First inspections and retightenings

after 500, 1,000 and 1,500 hours in
total service.
Engine lifetime
32,000

indicate so.
Pneumatic/hydraulic governor:
Oil change every 4,000 hours.
recommendations.
45,000
Clean before differential pressure

has increased 50% compared to sea
trial value.

Service Details Man BW PDF

Uploaded by

Copyright:

Available Formats

Service Details Man BW PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Details Man BW PDF

Uploaded by

Copyright:

Available Formats

Service Letter SL09-509/SBJ

Guiding Overhaul Intervals

Vice President, Engineering

Senior Manager, Engineering

Head office (& postal address)

Overhaul of cylinder unit on large bore

Forwarding & Receiving

Branch of MAN Diesel SE, Germany

Service Letter SL09-509/SBJ

Overhaul interval (hours)

Expected service life (hours) Remarks

Exhaust valve spindle

Inspection of seat and air spring:

Main hydraulic pump

To be obtained for DuraSpindle and

Pressure test at every 2nd piston

Normally, HVOF coated stems need

Proportional valve for

Check the overall cylinder condition

Replace valve after 20,000 hours

Pressure relief valve for

Replace sealings at overhaul

Exhaust valve actuator

Replace static sealing rings at overhaul.

16,000 Check and replace if required

Fuel oil pressure booster

Check and replace if required

Change piston rings on hydraulic piston and suction valve at overhaul.

Guiding Overhaul Intervals. Page  of 7 pages

Service Letter SL09-509/SBJ

Overhaul interval (hours)

Expected service life (hours) Remarks

Check for burned grooves at fuel valve

Check clearances and crankshaft

Tie rods including

Tighten rods and screws:

Holding down bolts

Tighten: once a year

Clean before differential pressure has

Flaps and butterfly

Check movement at every

Various fuel and

Lubricating oil bottom

Check timing and adjustment

Do not open bearings unless

Typically done at 5 years docking

New or overhauled chains to be

Replace after 5 years

MPC, MOP A, MOP B

Guiding Overhaul Intervals. Page  of 7 pages

Service Letter SL09-509/SBJ

Overhaul interval (hours)

Expected service life (hours) Remarks

Exhaust valve spindle

Pressure test at every 2nd piston

Inspection of seat and air spring:

Check the overall cylinder condition

Normally, HVOF coated stems need

To be obtained for Nimonic valve with

Guiding Overhaul Intervals. Page of 7 pages

Guiding Overhaul Intervals. Page of 7 pages

Guiding Overhaul Intervals. Page of 7 pages

Guiding Overhaul Intervals. Page of 7 pages

Guiding Overhaul Intervals. Page of 7 pages