Cteu en

Fieldbus modules CTEU/Installation system CTEL

Key features
The system
CTEU fieldbus modules for using
valve terminals
Festo-specific interface (I-Port)
Input modules CTSL for detecting
sensor signals
Direct and easy networking of valve
terminals and other devices via a
bus connection
Wide range of applications thanks

to high protection to IP65/67
Universal connection technology
(Sub-D, M12, terminal strip)
Optional decentralised installation
of bus node for connecting two
valve terminals
Basic diagnostics: undervoltage,
short circuit
CTEU for the universal use of valve

terminals. The Festo-specific,
uniformly defined interface (I-Port)
enables the fieldbus modules to be
used for different types of valve
terminal.
The following protocols are currently

supported:
CANopen
DeviceNet
CC-LINK
PROFIBUS
EtherCAT
AS-Interface
Online via: www.festo.com
Valve terminal configurator

A valve terminal configurator is
available online to help you select a
suitable valve terminal.
Select the valve terminal with I-Port
interface and order the associated
CTEU bus nodes. The bus nodes then
only need to be placed on the valve

terminal.
The ident. code for the valve terminals
specifies the valve functions, the num
ber of valves and vacant positions, as
well as the additional functions and
Internet: www.festo.com/catalogue/...
the type of compressed air supply.

As is the case with all Festo products,
all valve terminals are supplied:
Fully preassembled
Equipped with fittings on request

Tested for electrical function

Tested for pneumatic function
Securely packaged
Manuals can be downloaded free of
charge
Subject to change 2014/12

Key features
Fieldbus systems with CTEU
CANopen
CANopen was originally developed for
the automotive industry by a joint
venture led by Bosch. It has been
maintained by the organisation CiA
(CAN in Automation) since 1995, and
at the end of 2002 it was standard
ised as European standard
EN 50325-4.
DeviceNet
DeviceNet is an open fieldbus stand
ard that was developed by Rockwell
Automation on the basis of the CAN
protocol.
DeviceNet is standardised in
European standard EN 50325.
CC-Link
Control and Communications Link
(CC-Link) was developed by Mitsubishi
Electric and has been available as an
open fieldbus network since 1999.
PROFIBUS
Process Fieldbus (PROFIBUS) is a
fieldbus that was developed by
Siemens and has been standardised
in the IEC 61158 series of interna
tional standards. It enables commu
nication between devices without the
need for any specific adaptations to
the interface.
EtherCAT
EtherCAT is a bus with real-time cap
ability; it was developed by Beckhoff
and the EtherCAT Technology Group
(ETG). EtherCAT is an open technology
and has been standardised in interna
tional standards IEC 61158 and
IEC 61784 and in ISO 15745-4.
AS-interface
AS-interface is a manufacturer-inde
pendent, easy and robust installation
system. It was developed and repres
ented by the AS-International Associ
ation, a loose association of diverse
companies from different sectors.
AS-Interface has been standardised by
IEC 62026-2 and EN 50295.
2014/12 Subject to change

Key features
Integration of the I-Port interface/IO-Link
Different bus nodes are used for
integration in the control systems of
various manufacturers.
The following protocols are supported

with the compatible bus node CTEU:
CANopen
DeviceNet

EtherCAT
CC-LINK
PROFIBUS
AS-Interface
A second valve terminal can be con

nected via an electrical connecting
block (decentralised adapter). (p.6)
System overview, example
PLC
Fieldbus
Node CTEU (I-Port master) on

connecting block CAPC
CPX terminal with bus node

and CTEL master
Valve terminal VTUB-12
with fieldbus node CTEU
IO-Link/I-Port
Valve terminal CPV with

I-Port interface/IO-Link
Input module CTSL
Pneumatic drive
Pneumatic drive with sensor
Communication with higher-order

controller via fieldbus
Use a fieldbus node CTEU com

patible with the fieldbus protocol
Up to 64 inputs/outputs (solenoid
coils), depending on the valve
terminal

Key features
System overview
Example CTEU-AS interface
Valve terminal MPA-S
with bus node CTEU-AS
Compact AS-Interface
bus node
I/O modules
VTUB-12 Valve terminal

with CTEU-AS
bus node
CPX with control block
CESA
AS-Interface
Gateway
CTSL
input module
Connecting cable NEBU
Cable socket NEFU-X

Connecting block CAPC,
decentralised installation with
bus node CTEU-AS
Connecting cable NEBU
Power supply unit SVG for

AS-Interface systems

Peripherals overview
Overview of CTEU with valve terminal VTUG
7
8
aJ
aA
6
aB
aC
aD
aE
aF
3
Accessories
1
2
3
4
5
6
7
8
9
aJ
aA
aB
aC
aD
aE
aF
Manifold rail
Connecting block
H-rail adapter
Connecting cable
Bus node
Inscription label
Power supply socket
Terminal strip
Bus connection
Fieldbus socket
Plug connector
Bus connection
Plug connector
Plug connector
Threaded sleeve
Input module
Type
Brief description
Page/Internet
VABM
CAPC
CAFM
NEBU
CTEU
ASLR
NTSD
FBSD-KL
FBA-1
FBSD-GD, NECU
FBS, NECU
FBA-2
FBS-SUB-9-BU
FBS-SUB-9-WS
UNC
CTSL-D-16E
With I-Port interface, for connecting max. 35 valves

For connecting a further terminal (2x I-Port interface)
For connecting block CAPC
For IO-Link
For bus node

For power supply
For Open Style connection
Open Style for 5-pin terminal strip
For Micro Style connection, M12, 5-pin
For Micro Style connection, M12, 5-pin
Micro Style, 2xM12, 5-pin
Sub-D
Sub-D, angled
Sub-D mounting bolts
vtug
13
13
11, 13
15, 19, 25, 29, 35, 38
aslr
18, 23, 28, 33, 37
18/23
18/23
18/23, 33
18/23, 33
18/23, 33
18/23, 33
18, 33
18, 23, 28, 33
57

Key features Diagnostics
System diagnostics CTEU
Diagnostics LED on fieldbus node CTEU
The fieldbus-specific LEDs indicate the
communication status and the
fieldbus function.
Diagnostic messages via the fieldbus

A further LED indicates the status of
the power supply:
Undervoltage/short circuit
Power supply ensured
Interruption of voltage
Configuration error
Short circuit/overload of an output
module
Short circuit/undervoltage
Undervoltage/load voltage of the
valves
Fieldbus
1
1 Diagnostics via fieldbus

2 Bus-specific LEDs
3 Switching status display using
one LED per valve (on the
manifold rail)
4 Additional communication and
voltage status LED for
decentralised installation
5 I-Port interface to the fieldbus
module

Key features Power supply
Operating voltage and load current supply
The operating voltages for the valve
manifold with I-Port interface are
centrally connected to the bus node
via a 5-pin M12 plug connector.
The operating voltages are required

for the fieldbus node electronics and
the load supply to the valves
(supplied separately from the
electronics supply).
The power supplies do not have a

common 0V line and are thus
completely galvanically isolated from
one another.
Example power supply concept CTEU with valve terminal VTUG

Key features Power supply
Power supply concept
Example power supply concept CTEU with connecting block (decentralised adapter) CAPC and valve terminal VTUG

Technical data I-Port interface/IO-Link for valve terminal VTUG
Festo-specific, standardised interface
for direct connection to the fieldbus
by mounting the fieldbus node CTEU
or to an IO-Link master via a cable (in
IO-Link mode).
Versions:
I-Port interface for fieldbus nodes
(CTEU)
IO-Link mode for direct connec
tion to a higher-order IO-Link
master
The electrical supply/transmission

of communication data takes place
via an M12 plug connector.
The following protocols are

supported:
CANopen
DeviceNet

CC-Link
PROFIBUS
EtherCAT
AS-Interface
General technical data

Communication types
Electrical connection
Baud rates
COM3
COM2
Intrinsic current consumption, logic supply PS
Intrinsic current consumption, valve supply PL
Max. number of solenoid coils
VAEM-L1-S-8-PT
VAEM-L1-S-16-PT
VAEM-L1-S-24-PT
Max. number of valve positions
VAEM-L1-S-8-PT
VAEM-L1-S-16-PT
VAEM-L1-S-24-PT
Ambient temperature
Degree of protection to EN 60529
[kbps]
[kbps]
[mA]
[mA]
[C]
IO-Link
M12 plug connector, 5-pin
A-coded
Metal thread for screening
230.4
38.4
30
30
16
32
48
8
16
24
5 +50
IP67
LED display
Status LED X1
Colour
Status
Function
Red/green
2
3
4
5
Off
Status green
Flashing green
Flashing red/green
Static red
No 24 V logic
Everything OK
Communication error (in the I-Port or IO-Link protocol)
Load supply error (undervoltage or no load supply)
Load supply error and communication error
Pin allocation I-Port interface/IO-Link
10
Pin
Allocation
Description
24VEL/SEN
Operating voltage supply (electronics, sensors/inputs)
24VVAL/OUT
Load voltage supply (valves/outputs)
0VEL/SEN
C/Q
Data communication
0VVAL/OUT

Technical data I-Port interface/IO-Link for valve terminal VTUG
Download CAD data www.festo.com
Dimensions
Outlet on top
Outlet on the side
Type
VAEM-L1-S-
B1
Outlet on top
L1
H1
B1
Outlet on the side

L1
L2
91
47.1
25
91.5
47.1
10
Accessories I-Port interface/IO-Link

Description
Part No.
Type
Electrical interface for I-Port interface/IO-Link, outlet on top

Actuation of up to 8 double solenoid valve positions
573384
573939
573940
VAEM-L1-S-8-PT
VAEM-L1-S-16-PT
VAEM-L1-S-24-PT
Electrical interface for I-Port interface/IO-Link, outlet on the side

574207
574208
574209
VAEM-L1-S-8-PTL
VAEM-L1-S-16-PTL
VAEM-L1-S-24-PTL
Connection technology for I/O-Link

T-adapter M12, 5-pin for IO-Link and load supply
171175
FB-TA-M12-5POL
175487
SEA-M12-5GS-PG7
565306
ASLR-C-E4
574321
574322
574323
NEBU-M12G5-E-5-Q8N-M12G5
NEBU-M12G5-E-7.5-Q8N-M12G5
Straight Plug connector , for I-Port/IO-Link

Straight plug connector, M12, 5-pin
(in combination with adapter for separate load supply)
Inscription label for I-Port/IO-Link
40 pieces in frame
Connecting cable
11

Technical data Connecting block CAPC
Function
The connecting block CAPC enables
decentralised installation of fieldbus
nodes CTEU on a valve terminal or
input modules with I-Port interface.
Application
M12 connection technology
(two interfaces)
Enables the installation of valve
terminals or other devices over a
distance of 20 metres
Accessory CAFM enables the
connecting block to be installed on
an H-rail

Type
CAPC-F1-E-M12
Dimensions W x L x H
Fieldbus interface
Operating voltage range
Max. power supply
Nominal operating voltage
Product weight
Cable length
[mm]
[V DC]
[A]
[V DC]
[g]
[m]
50x148x28
2 x M12 socket, 5-pin, A-coded
18 30
2
24
85
20
Materials
Housing
Note on materials
PA reinforced
RoHS compliant
Operating and environmental conditions

Ambient temperature
Storage temperature
Corrosion resistance class CRC
CE marking (see declaration of conformity)
1)
2)
12
[C]
[C]
IP65, IP67
5 +50
20 +70
21)
To EU EMC Directive2)
Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or
media such as coolants or lubricating agents.
For information about the applicability of the component see the manufacturers EC declaration of conformity at: www.festo.com/sp User documentation.
If the component is subject to restrictions on usage in residential, office or commercial environments or small businesses, further measures to reduce the emitted interference may be necessary.

Technical data Connecting block CAPC
CAPC with mounted fieldbus node CTEU-CO
Dimensions
CAPC
Type
B1
B2
B3
B4
B5
D1-N-
H1
H2
H3
H4
H5
H6
L1
L2
CAPC
148
140
32
6.6
91
4.4
27.3
20.3
19.3
9.6
5.7
54.8
50
40

Pin
Allocation
1
24VEL/SEN
2
24VVAL/OUT
3
0VEL/SEN
4
C/Q
5
0VVAL/OUT
Housing, FE
Description
Data communication
Functional earth
Accessory CAPC
Description
Part No.
Type
570042
CAPC-F1-E-M12
570043
CAFM-F1-H
574321
574322
574323
Connecting block
H-rail mounting
Connecting cable
13

Technical data CTEU-CO
The bus node handles communication
between the valve terminal and a
higher-order CANopen master.
The module has basic diagnostic
functions. It has 5 integrated LEDs for
on-site display. A maximum of 8 byte
inputs and 8 byte outputs are trans
mitted in the cyclic process image.
Application
Fieldbus connection
The bus connection is established
via a 9-pin Sub-D plug connector
(pin) as per the CAN in Automation
(CiA) specification DS 102 with
additional 24 V CAN transceiver
supply (option as per DS 102).
The bus connector plug (with degree

of protection IP65/IP67 from Festo
or IP20 from other manufacturers)
facilitates the connection of an in
coming and an outgoing bus cable.
There are 4 contacts each available

for the conductors (CAN_L/CAN_H
and 24 V/0 V optional) of the in
coming and outgoing bus cables.
The fieldbus parameters and the

basic device parameter settings are
set on the bus node via DIL
switches.
Max. CANopen cable length (trunk

cable):
40 m at 1 Mbps
100 m at 500 kbps
250 m at 250 kbps
500 m at 125 kbps
Max. branch cable length (drop

cable):
0.30 m at 1 Mbps
0.75 m at 500 kbps
2.00 m at 250 kbps
3.75 m at 125 kbps
The following variants can be

realised using an adapter:
2 x Micro Style M12, degree of
protection IP65, 5-pin, socket
and pin
Open Style plug connector,
degree of protection IP20, 5-pin,
pin
Implementation
Protocol chip used:
CAN transceiver 82C251
Baud rates supported:
125 kbps
250 kbps
500 kbps
1 Mbps
14

Fieldbus interface
Protocol
Baud rates
Internal cycle time
Operating voltage
[kbps]
Nominal value
Permissible range
Intrinsic current consumption at nominal operating voltage
Max. power supply
Parameterisation
[V DC]
[V DC]
[mA]
[A]
Max. address capacity, inputs

Max. address capacity, outputs
Additional functions
Operating elements
Configuration support
Device-specific diagnostics
LED display
Fieldbus-specific
Product-specific

Note on materials
Information on housing materials
Product weight
Temperature range
CE marking
Certification
1)
2)
Environment
Storage
[g]
[C]
[C]
[mm]
Sub-D socket, 9-pin

Sub-D plug connector, for self-assembly
2x M12x1, 5-pin
5-pin terminal strip
CANopen
125, 250, 500 and 1000
1 ms per 1 byte of user data
24
18 30
Typically 65
4
Diagnostic behaviour
Fail state
8 byte
8 byte
Emergency message
Acyclic data access via "SDO"
DIL switches
EDS files
System diagnostics
Undervoltage
Communication errors
MNS: Network status
IO: I/O status
PS: Operating voltage for electronics and load supply
X1: System status of module at I-Port 1
IP65/IP67
RoHS compliant
PC
PA reinforced
90
5 +50
20 +70
40 x 91 x 50
21)
C-Tick

15

Dimensions
CTEU-CO
Type
B1
H1
L1
CTEU-CO
91
39.8
40
Pin allocation
Pin
Allocation
Description
1
2
3
4
5
6
7
8
9
Housing
n.c.
CAN_L
CAN_GND
n.c.
CAN_SHLD
GND
CAN_H
n.c.
CAN_V+
Not connected
Received/transmitted data low
0 V CAN interface (connected to pin 6)
Not connected
Optional screened connection
0 V CAN interface, optional (connected to pin 3)
Received/transmitted data high
Not connected
24 V DC supply CAN interface
Cable screening, connection to functional earth FE
24VEL/SEN
24VVAL/OUT
0VEL/SEN
0VVAL/OUT
FE
Functional earth
Sub-D, 9-pin, CANopen interface
Power supply, M12, B-coded
16

Pin allocation of the CANopen interface
Fieldbus plug connector/adapter
Pin
Allocation
Description
FE
Functional earth
CAN_V+
CAN_GND
0 V CAN interface
CAN_H
CAN_L
Bus connection, FBA-2-M12-5POL

2
2
3
11
Bus IN
Bus OUT
Bus connection, FBA-1-SL-5POL with FBSD-KL-2X5POL

1
CAN_GND
1
0 V CAN interface
CAN_L
FE
Functional earth
CAN_H
CAN_V+
Connection and display components
1
2
3
4
Status LED (operating status/diagnostics)

DIL switch
Power supply for bus node and connected devices (valve terminal)
Fieldbus connection (Sub-D plug connector)
17

Accessories CTEU-CO
Ordering data
Part No.
Type
CANopen bus node
570038
CTEUCO
Sub-D plug connector, straight
532219
FBS-SUB-9-BU-2x5POL-B
Sub-D plug connector, angled
533783
FBS-SUB-9-WS-CO-K
Micro Style bus connection, 2xM12, 5-pin, A-coded
525632
FBA-2-M12-5POL
Fieldbus socket for Micro Style connection, A-coded
18324
FBSD-GD-9-5POL
Plug connector for Micro Style connection, M12, 5-pin, A-coded
175380
FBS-M12-5GS-PG9
Open Style bus connection
525634
FBA-1-SL-5POL
Terminal strip for Open Style connection, 5-pin
525635
FBSD-KL-2x5POL
Threaded sleeve for Sub-D
533000
UNC4-40/M3X8
For power supply
538999
NTSDGD9M125POLRK
573767
573768
573769
573770
573771
573772
P.BE-CTEU-CO-OP+MAINT-DE
P.BE-CTEU-CO-OP+MAINT-EN
P.BE-CTEU-CO-OP+MAINT-ES
P.BE-CTEU-CO-OP+MAINT-FR
P.BE-CTEU-CO-OP+MAINT-IT
P.BE-CTEU-CO-OP+MAINT-ZH
Bus node
Bus connection
Fitting
Plug socket
Manual
Manual Bus node CTEU-CO
18
German
English
Spanish
French
Italian
Chinese

Technical data CTEU-DN
higher-order DeviceNet master.
inputs and 8 byte outputs
are typically transmitted in the cyclic
process image.
Application
Fieldbus connection
via a 9-pin Sub-D socket with a
typical allocation (to EN 50170).
The bus connector plug (with degree

of protection IP65/IP67 from Festo
or IP20 from other manufacturers)
facilitates the connection of an
incoming and an outgoing bus

cable.
The fieldbus parameters and the
basic device parameter settings are
set on the bus node via DIL

switches.
Max. DeviceNet cable length (trunk

cable):
100 m at 500 kbps
250 m at 250 kbps
500 m at 125 kbps
Max. branch cable length (drop

cable):
6 m at 500 kbps
6 m at 250 kbps
6 m at 125 kbps

2 x Micro Style M12, degree of
protection IP65, 5-pin, socket
and pin
Open Style plug connector,
degree of protection IP20, 5-pin,
pin
Implementation
Protocol chip used:
CAN transceiver 82C251
125 kbps
250 kbps
500 kbps
19

Fieldbus interface
Protocol
Baud rates
Internal cycle time
Operating voltage
[kbps]
Nominal value
Permissible range
Max. power supply
Parameterisation
[V DC]
[V DC]
[mA]
[A]

Operating elements
LED display
Fieldbus-specific
Product-specific

Note on materials
Product weight
Temperature range
CE marking
Certification
1)
2)
20
Environment
Storage
[g]
[C]
[C]
[mm]
Sub-D socket, 9-pin

2x M12x1, 5-pin
5-pin terminal strip
DeviceNet
125, 250, 500
24
18 30
Typically 65
4
Failsafe and idle response
8 byte
8 byte
Acyclic data access via "Explicit Message"
Quick connect
System status can be represented using process data
DIL switches
EDS files
System diagnostics
Undervoltage
MNS: Network status
IO: I/O status
IP 65/IP 67
RoHS compliant
PC
PA reinforced
90
5 +50
20 +70
40 x 91 x 50
21)
C-Tick


Dimensions
CTEU-DN
Type
B1
H1
L1
CTEU-DN
40
39.8
91
Pin allocation
Pin
Allocation
Description
1
2
3
4
5
6
7
8
9
Housing
n.c.
CAN_L
CAN_GND
n.c.
CAN_SHLD
GND
CAN_H
n.c.
CAN_V+
Not connected
0 V CAN interface (connected to pin 6)
Not connected
Optional screened connection
0 V CAN interface, optional (connected to pin 3)
Not connected
24VEL/SEN
24VVAL/OUT
0VEL/SEN
0VVAL/OUT
FE
Functional earth
Sub-D, 9-pin, DeviceNet interface
Power supply, M12, B-coded
21

Pin allocation for the DeviceNet interface
Pin
Allocation
Description
FE
Functional earth
CAN_V+
CAN_GND
0 V CAN interface
CAN_H
CAN_L
Bus connection, FBA-2-M12-5POL

2
2
3
11
Bus IN
Bus OUT
Bus connection, FBA-1-SL-5POL with FBSD-KL-2X5POL

1
CAN_GND
1
0 V CAN interface
CAN_L
FE
Functional earth
CAN_H
CAN_V+
22
1
2
3
4

DIL switch group

Accessories CTEU-DN
Ordering data
Part No.
Type
DeviceNet bus node
570039
CTEUDN
532219
FBS-SUB-9-BU-2x5POL-B
Micro Style bus connection, 2xM12, 5-pin, A-coded
525632
FBA-2-M12-5POL
Fieldbus socket for Micro Style connection, M12, 5-pin
18324
FBSD-GD-9-5POL
Plug connector for Micro Style connection, M12, 5-pin
175380
FBS-M12-5GS-PG9
Open Style bus connection
525634
FBA-1-SL-5POL
Terminal strip for Open Style connection, 5-pin
525635
FBSD-KL-2x5POL
533000
UNC4-40/M3X8
For power supply
538999
NTSDGD9M125POLRK
573744
573745
573746
573747
573748
573779
P.BE-CTEU-DN-OP+MAINT-EN
P.BE-CTEU-DN-OP+MAINT-EN
P.BE-CTEU-DN-OP+MAINT-ES
P.BE-CTEU-DN-OP+MAINT-FR
P.BE-CTEU-DN-OP+MAINT-IT
P.BE-CTEU-DN-OP+MAINT-ZH
Bus node
Bus connection
Fitting
Plug socket
User documentation
Manual Bus node CTEU-DN
German
English
Spanish
French
Italian
Chinese
23

Technical data CTEU-CC
higher-order master for Control &
Communication Link (CC-Link).
inputs and 8 byte outputs
are transmitted in the cyclic process
image.
Application
Fieldbus connection
by means of a screw terminal with
IP20 degree of protection, a 9-pin
Sub-D plug connector with
IP65/IP67 degree of protection from
Festo or a Sub-D plug connector
with IP20 degree of protection from
other manufacturers.
The module has a system and load

supply, a fieldbus connection and a
connection to the valve terminal
with serial I-Port interface.
Both connection types have the

function of an integrated T-distrib
utor and thus support the connec
tion of an incoming and outgoing
bus cable.
When using branch lines: maximum

branch line length 8 m, maximum 6
stations per branch line
Length of main string:
100 m at 625 kbps, total length
of branch line 50 m
500 m at 156 kbps, total length
of branch line 200 m
Higher baud rates not permitted
with branch line.

The integrated interface with RS485

transmission technology is designed
for the typical CC-Link 3-wire con
nection technology (in accordance
with CLPA CC-Link Spec. V1.1).
Implementation
Protocol chip used:
MFP3 from Mitsubishi
Maximum CC-Link cable length
(minimum 0.2 m between devices):
100 m at 10 Mbps
150 m at 5 Mbps
200 m at 2.5 Mbps
600 m at 625 kbps
1200 m at 156 kbps
24
Spring-loaded terminal In/Out

with IP65 degree of protection
(adapter 532220)
Screw-in clamping connector with
IP20 degree of protection
(adapter 197962)

Fieldbus interface
Protocol
Baud rates
Internal cycle time
Operating voltage
[kbps]
Nominal value
Permissible range
Max. power supply
Operating elements
[V DC]
[V DC]
[mA]
[A]
Parameterisation
LED display
Fieldbus-specific
Product-specific

Note on materials
Temperature range
Product weight
CE marking
Certification
1)
2)
Environment
Storage
[C]
[C]
[mm]
[g]
Sub-D socket, 9-pin

Screw terminal strip, IP20
CC-Link
156 10000
24
18 30
Typically 70
4
16 byte
16 bytes
DIL switches
System diagnostics
Undervoltage
Communication error
System status can be displayed using process data
Activate diagnostics
Fail-safe and idle response
Err: data transmission error
Run: bus active
IP65/IP67
RoHS compliant
PC
PA reinforced
5 +50
20 +70
40 x 91 x 50
90
21)
C-Tick

25

Dimensions
CTEU-CC
Type
B1
H1
L1
CTEU-CC
91
39.8
40
Pin allocation
Pin
Allocation
Description
1
2
3
4
5
6
7
8
9
Housing
n.c.
DA
DG
n.c.
n.c.
n.c.
DB
n.c.
n.c.
Not connected
Data transmission line A
Data transmission line ground (data reference potential)
Not connected
Not connected
Not connected
Data transmission line B
Not connected
Not connected
24VEL/SEN
24VVAL/OUT
0VEL/SEN
0VVAL/OUT
FE
Functional earth
Sub-D, 9-pin, CC-Link interface
Power supply, M12, AB-coded
26

Technical data CTEU-CC-Link
Pin allocation for the CC-Link interface
Pin
Description
Bus connection with terminal strip, FBA-1-KL-5POL

FE
Functional earth
SLD
Cable screening
DG
DB
DA
DA
DB
DG
n.c.
Not connected
FE
Connected to the housing of the Sub-D plug connector by means of the clamp strap
Bus connection, FBS-SUB-9-GS-24XPOL-B
1
2
3
4

DIL switch
27

Accessories CTEU-CC-Link
Ordering data
Part No.
Type
CC-Link bus node
1544198
CTEUCC
532220
FBS-SUB-9-GS-2x4POL-B
Screw terminal bus connection
197962
FBA-1-KL-5POL
533000
UNC4-40/M3X8
For power supply, M12x1, 5-pin
18324
FBSDGD95POL
Bus node
Bus connection
Fitting
Plug socket
28

Technical data CTEU-PB
higher-order master for
PROFIBUS DP.
inputs and 8 byte outputs are trans
mitted in the cyclic process image.
Application
Fieldbus connection
via a 9-pin Sub-D socket with a
typical PROFIBUS allocation (to
EN 50170).
The bus connector plug (with

IP65/IP67 protection from Festo or
IP20 protection from other manu
facturers) facilitates the connection
of an incoming and an outgoing bus
cable.
An active bus terminal can be

connected using the DIL switch
integrated in the plug connector.
The Sub-D interface is designed for

controlling network components
with a fibre-optic cable connection.
Maximum fieldbus length:

1200 m
1200 m
1200 m
1000 m
400 m
200 m
100 m
Maximum branch line length:

500 m
500 m
100 m
33.3 m
20 m
6.6 m
RS 485 transceiver used: Analog

Devices ADM 2485
PROFIBUS Slave Controller used:
Profichip VPC+S
Baud rates/overview of cable lengths

9.6 kbps
19.2 kbps
93.75 kbps
187.5 kbps
500 kbps
1.5 Mbps
3 Mbps - 12 Mbps
29

Fieldbus interface
Protocol
Baud rates
[kbps]
[Mbps]
Internal cycle time

Operating voltage
Nominal value
Permissible range
Max. power supply
Parameterisation
[V DC]
[V DC]
[mA]
[A]

Operating elements
LED display
Fieldbus-specific
Product-specific

Note on materials
Product weight
Temperature range
CE marking
Certification
1)
2)
30
Environment
Storage
[g]
[C]
[C]
[mm]
Sub-D socket, 9-pin

2x M12x1, 5-pin, B-coded
PROFIBUS DP
9.6, 19.2, 93.75, 187.5, 500
1.5, 12
24
18 30
Typically 100
2
Fail-safe response
16 byte
16 byte
System status using diagnostics program
Emergency message
DIL switches
GSD files
System diagnostics
Undervoltage
BF: Bus fault
IP65/IP67
RoHS compliant
PC
PA reinforced
90
5 +50
20 +70
40 x 91 x 50
21)
C-Tick


Dimensions
CTEU-PB
Type
B1
H1
L1
CTEU-PB
91
39.8
40
Pin allocation
Pin
Allocation
Description
1
2
3
4
5
6
7
8
9
Housing
Screening
n.c.
RxD/TxD-P
CNTR-P
DGND
VP
n.c.
RxD/TxD-N
n.c.
Functional earth
Not connected
Received/transmitted data positive
Repeater control signal
Data ground
Supply voltage positive (+ 5 V)
Not connected
Received/transmitted data negative
Not connected
24VEL/SEN
24VVAL/OUT
0VEL/SEN
0VVAL/OUT
FE
Functional earth
Sub-D, 9-pin, PROFIBUS interface
Power supply, M12, A-coded
31

Pin allocation for PROFIBUS interface
Fieldbus adapter
Pin
Bus IN
Bus OUT
n.c.
VP
RxD/TxD-N
RxD/TxD-N
n.c.
DGND
RxD/TxD-P
RxD/TxD-P
FE
Functional earth
Bus connection, FBA-2-M12-5POL-RK

2
3
2
3
5
1 1
5
4
Bus IN
4
Bus OUT
32
1
2
3
4

DIL switch

Accessories CTEU-PB
Ordering data
Part No.
Type
PROFIBUS bus node
570040
CTEUPB
532216
FFBS-SUB-9-GS-DP-B
Sub-D plug connector, angled
533780
FBS-SUB-9-WS-PB-K
Bus connection M12 adapter, B-coded
533118
FBA-2-M12-5POL-RK
Straight socket, M12x1, 5-pin, for assembling a connecting cable compatible with
FBA-2-M12-5POL-RK
1067905
NECU-M-B12G5-C2-PB
Straight plug connector, M12x1, 5-pin, for assembling a connecting cable compatible
with FBA-2-M12-5POL-RK
1066354
NECU-M-S-B12G5-C2-PB
Terminating resistor, M12, B-coded for PROFIBUS
1072128
CACR-S-B12G5-220-PB
533000
UNC4-40/M3X8
18324
FBSDGD95POL
575392
575393
575394
575395
575396
575397
P.BE-CTEU-PB-OP+MAINT-DE
P.BE-CTEU-PB-OP+MAINT-EN
P.BE-CTEU-PB-OP+MAINT-ES
P.BE-CTEU-PB-OP+MAINT-FR
P.BE-CTEU-PB-OP+MAINT-IT
P.BE-CTEU-PB-OP+MAINT-ZH
Bus node
Bus connection
Fitting
Plug socket
User documentation
Manual Bus node CTEU-PB
German
English
Spanish
French
Italian
Chinese
33

Technical data CTEU-EC
higher-order master for EtherCAT.
functions.
It has 6 integrated status LEDs for
on-site display.
A maximum of 16 byte inputs and
16 byte outputs are transmitted in the
cyclic process image.
Application
Fieldbus connection
The bus connection is established via
two M12 sockets, D-coded to
IEC61076-2-101 with IP65/67
degree of protection.
Both connections are equivalent
100BaseTX Ethernet ports with integ
rated auto MDI functionality (crossover and patch cables can be used)
that are brought together via an

internal switch.
supply, a fieldbus connection and a
connection to the valve terminal with
serial I-Port interface.
Please observe the applicable

specifications such as the cable
specifications for Ethernet networks
ISO/IEC11801 and ANSI/TIA/
EIA-568-B.
Maximum cable length (between

network stations): 100 m
Transmission rate:
100 Mbps
EtherCAT communication chip:
ASIC ET1100
EtherCAT bus node

The EtherCAT bus node supports the
EtherCAT protocol based on the
Ethernet standard and TCP/IP
technology to IEEE802.3.
This guarantees a data exchange with
a high data transmission rate, for
example I/O data from sensors,
actuators or robot controllers, PLCs or
process equipment. Furthermore, non
34
real-time critical information such as

diagnostic information, configuration
information, etc. can be transferred.
The data bandwidth is sufficient to
transmit both data types (real-time
and non-real-time) in parallel.
The bus node has a system and load
supply, EtherCAT input and output
port, LEDs for status and diagnostic

messages and DIL switch elements.
Diagnostics is possible directly at the
bus node and/or via fieldbus.
The bus node has separate operating
and load voltage supplies.
The bus node is mounted on an I-Port
compatible device (e.g. valve terminal
or connecting block) from Festo.
The bus node supplies voltage to

downstream devices connected by
means of the I-Port interface.
The following can be set via DIL
switch:
Station addresses
Diagnostics on/off
Fail state behaviour

Fieldbus interface
Protocol
Baud rates
Internal cycle time
Operating voltage (PS)
Load voltage (PL)
[Mbps]
Nominal value
Permissible range
Power failure buffering
Max.
Typical tolerance range
Max. power supply

LED display
Fieldbus-specific
[V DC]
[V DC]
[ms]
[V DC]
[V DC]
[A]
[mA]
[byte]
[byte]
Product-specific
Parameterisation
Operating elements
Parameterisation via
DIL switches
Certification
Temperature range
Operation
Storage/transport
Note on materials
Product weight
1)
2)
[C]
[C]
[mm]
[g]
2x M12 socket, D-coded, 4-pin

EtherCAT
100
24
18 30
10
30
18 30
4
Typically 60
16
16
Run: operating status (communication status)
L/A2: network active (connection status) port 2 (Out)
L/A1: network active (connection status) port 1 (In)
System diagnostics
Undervoltage
Communication error
Diagnostic object
Acyclic data access via "SDO"
Emergency message
Modular device profile (MDP)
XML file
Fail-safe response
DIL switches
Fail-safe and idle response
Diagnostics on/off
IP65
21)
C-Tick
5 +50
20 +70
RoHS compliant
PC
PA reinforced
40 x 91 x 50
90

35

Dimensions
CTEU-EC
Type
B1
H1
L1
CTEU-EC
91
45.3
40
Pin allocation
Pin
Allocation
Description
TX+
Transmitted data+
RX+
Received data+
TX-
Transmitted data-
RX-
Received data-
EtherCAT interface, M12, D-coded
Housing
Power supply, M12, A-coded

1
24VEL/SEN
24VVAL/OUT
0VEL/SEN
0VVAL/OUT
FE
Functional earth
1
2
3
4

DIL switch
4
2
4
36

Accessories CTEU-EC
Ordering data
Part No.
Type
EtherCAT bus node
572556
CTEUEC
Plug connector M12x1, 4-pin, D-coded
543109
NECU-M-S-D12G4-C2-ET
18324
FBSDGD95POL
575400
575401
575402
575403
575404
575405
P.BE-CTEU-EC-OP+MAINT-DE
P.BE-CTEU-EC-OP+MAINT-EN
P.BE-CTEU-EC-OP+MAINT-ES
P.BE-CTEU-EC-OP+MAINT-FR
P.BE-CTEU-EC-OP+MAINT-IT
P.BE-CTEU-EC-OP+MAINT-ZH
Bus node
Bus connection
Plug socket
User documentation
Manual Bus node CTEU-EC
German
English
Spanish
French
Italian
Chinese
37

Technical data CTEU-AS
higher-order AS-Interface master.
Activation of up to 16 solenoid coils
per valve terminal
Automatic addressing
Automatic detection of the number
of connected valves
Properties
supply, a bus connection and a con
nection to the valve terminal with
serial I-Port interface.

functions. It has 3 integrated LEDs
for on-site display.
A maximum of 2 byte inputs and

2 byte outputs are transmitted in
the cyclic process image.

Fieldbus interface
Protocol
Internal cycle time
Operating voltage
Nominal value
Permissible range
Max. power supply
Operating elements
[ms]
[V DC]
[V DC]
[mA]
[A]
Parameterisation
LED display

Note on materials
Temperature range
Product weight
CE marking
1)
2)
38
Bus-specific
Product-specific
Environment
Storage
[C]
[C]
[mm]
[g]
Plug connector M12x1, 4-pin, A-coded

Socket M12x1, 4-pin, A-coded
AS-Interface
10
30
20 31.6
Typically 50
4
2 byte
2 bytes
DIL switches
System diagnostics
Undervoltage
Communication error
Watchdog enable
Watchdog disable
AS-Interface operation
IP65/IP67
RoHS compliant
PA reinforced
5 +50
20 +70
40 x 91 x 50
90
21)


Technical data CTEU-AS
Dimensions
CTEU-AS
Type
B1
H1
H2
L1
CTEU-AS
91
45.3
39.7
40
Pin allocation
Pin
Allocation
AS-Interface +
24 V load voltage supply
AS-Interface
AS-Interface +
AS-Interface
M12 plug connector, AS-Interface In
M12 socket, AS-Interface Out
3
4
1
2
3
4

DIL switch
M12 plug connector, AS-Interface bus and auxiliary power supply (AS-Interface In)
M12 socket, AS-Interface bus and auxiliary power supply (AS-Interface Out)
39

Accessories CTEU-AS
Ordering data
Part No.
Type
572555
CTEUAS
Bus node
AS-Interface bus node
Cable socket with load voltage supply

Flat cable
4-pin socket, M12x1,

A-coded
572226
NEFU-X24F-M12G4
4-pin socket, M12x1,

A-coded
1m
572227
NEFU-X24F-1-M12G4
4-pin socket, M12x1, A-coded
572225
NEFU-X22F-M12G4
5-pin socket, M12x1, A-coded
18788
ASI-SD-FK-M12
4-pin straight socket, M12x1,

A-coded
18789
ASI-SD-PG-M12
Yellow
18940
KASI-1,5-Y-100
Black
18941
KASI-1,5-Z-100
Cable sleeve for insulating and sealing the flat cable
165593
ASI-KT-FK
Cable cap for insulating and sealing the flat cable
18787
ASI-KK-FK
Flat cable
Cable socket without load voltage supply

Flat cable
Flat cable, screw terminal
Flat cable
AS-Interface flat cable
Connecting cable
40
4-pin straight plug connector,

M12x1, A-coded
4-pin angled socket, M12x1,

A-coded
1m
185499
KM12-M12-GSWD-1-4
4-pin straight plug connector,

M12x1, A-coded
4-pin straight socket,

M12x1, A-coded
2.5 m
18684
KM12-M12-GSGD-2,5
5.0 m
18686
KM12-M12-GSGD-5

Technical data Interface CPX-CTEL
The electrical interface CPX-CTEL
master establishes the connection to
modules of the CTEL/CTEU series that
have an I-Port interface (device). The
I/O data from the connected devices
are transmitted to the connected CPX
bus node and thus to the higher-order
controller via fieldbus.
A maximum of 4 devices can be
connected to a CPX-CTEL master via
appropriate M12 interfaces.
Application
I-Port interface
As well as transmitting the commu
nication data, the I-Port interfaces of a
CPX-CTEL master also transmit the
power supply to the connected

sensors and the load supply to the
valves (or outputs). Both circuits are
supplied separately with 24 V, using a

separate reference potential.
The connecting cables used must meet
the enhanced requirements resulting

from the dual function of signal cable
and supply cable.
Configuration example CPX-CTEL master with CTEL modules

The CPX-CTEL master provides 4
external I-Port interfaces, to each of
which a device can be connected.
I-Port is an interface for the exchan
ging of serial data for connecting
decentralised modules or valve
terminals from Festo. The I-Port
interface is based on IO-Link and is
compatible with it in certain areas.
The connection type corresponds to
a star topology. In other words, only
one module or valve terminal can be
connected to each I-Port.
The restrictions compared to IO-Link

include:
Permanently set baud rate of
230.4 kbps
SIO mode is not supported
A maximum of 32 bytes of input
data and 32 bytes of output data
Only one dump of the master
commands is used
Festo plug & work principle,
configuration via IODD is not
supported
41

Implementation
The CPX-CTEL master from Festo en
ables modules with an I-Port interface
to be connected to a CPX system:
A maximum of 4 devices with indi
vidual electronic fuse protection
A maximum of 64 inputs/
64 outputs per I-Port interface
The maximum length of a string is
20 m
Configuration
Settings
The precise number of the I/O bytes
made available depends on the re
quirements of the connected devices
or of the suitable selected operating
mode.
The operating mode or preset config
uration of the CPX-CTEL master can be
specified by the user.
DIL switches are used for selecting the
operating mode and setting the
manual configuration. These DIL
switches are not required during
continuous operation and are only
accessible in the disassembled state.
The following device variants are

available:
Input modules with 16 digital
inputs (3-pin M8 and 5-pin M12
connection technology)
Valve terminals with I-Port interface
(up to 48 solenoid coils, different
valve functions)
The decentralised arrangement of the

modules and valve terminals with
I-Port enables them to be mounted
close to the cylinders and actuators or
sensors to be controlled. This means
that the compressed air supply lines
and sensor cables used can be
shortened, and it may be possible to
use smaller valves, thereby saving
costs.
Manual configuration
Several CPX-CTEL masters can be com

bined in one CPX terminal, depending
on the address capacity of the bus
node.
Example:
CPX-FB13 (512 I/O)
A maximum of 2 CPX-CTEL masters
is possible (each with 256 E/A)
Automatic configuration
In the case of manual configuration

(tool change mode), the volume of in
puts and outputs in the process image
of the CPX system or of the higherlevel fieldbus can be defined
manually using the DIL switches.
The process image then always has

the same scope, regardless of the
connected devices.
The I/O length specified always
applies to all four I-Ports (max.
8 bytes per I-Port).
In the case of automatic configura

tion, the I/O length for each I-Port is
determined individually and this
value is used to select the appropriate
or next highest configuration preset.
The power supply for the devices and

the inputs is provided by the power
supply for the electronics and sensors
of the CPX terminal.
The power supply for the outputs and
valves is provided by the power supply
for the valves of the CPX terminal.

The interlinking block with additional
power supply ensures a separate
voltage supply for the valves and out
puts. This allows the supply voltage to
be disconnected separately.
The valves and outputs of the connec
ted I-Port devices can therefore be
disconnected separately without
disconnecting the devices.
Power supply for I-Port devices

The CPX-CTEL master provides two
separate power supplies for the
connected devices:
For operating of the device and the
inputs connected to it
For the outputs and valves that are
connected to the device
42

Type
Protocol
Maximum address capacity
I-Port connection
Number of I-Port interfaces
Max. cable length
Internal cycle time
Electrical isolation
CPX-CTEL-4-M12-5POL
Outputs
Inputs
[bit]
[bit]
[m]
[ms]
Channel channel
Channel internal bus
LED displays
Diagnostics
Parameterisation
Operating elements
Operating voltage
Nominal value
Permissible range
Power failure buffering
Max. power supply per channel
Max. residual current of outputs per channel
Temperature range
Operation
Storage/transport
Materials
Note on materials
Grid dimension
Dimensions (incl. interlinking block) W x L x H
Product weight
-H-
[V DC]
[V DC]
[ms]
[mA]
[A]
[A]
[C]
[C]
[mm]
[mm]
[g]
I-Port
256
256
4x socket M12, 5-pin, A-coded
4
20
1 per 8 bits of user data
No
Yes, using an intermediate supply
X1 4 = status of the I-Port interface 1 4
PS
= Electronic supply
PL
= Load supply
-P= Module error
Communication error
Module short circuit
Module-oriented diagnostics
Undervoltage
Fail-safe mode per channel
Forcing per channel
Idle mode per channel
Module parameters
Tool change mode
Tool change mode
DIL switches
24 (polarity-safe)
18 30
10
Typically 65
4x 1.6
4x 1.6
IP65/IP67
5 +50
20 +70
PA reinforced, PC
RoHS compliant
50
50 x 107 x 55
110
Note
Please observe the general limits and

guidelines for the system when
configuring the electrical modules.
43

1
1 Status LEDs for I-Port interfaces

2 CPX-specific status LEDs
3 Holders for inscription labels
(IBS 6x10)
4 I-Port interfaces for up to
4 devices

Pin
Allocation
Description
24VEL/SEN
24VVAL/OUT
0VEL/SEN
C/Q
Data communication
0VVAL/OUT
Dimensions
Type
CPX-CTEL-4-M12-5POL
44
B1
B2
B3
H1
L1
108.1
118.9
124.9
55.1
50

Accessories Interface CPX-CTEL
Ordering data
Description
Part No.
Type
Interface for a maximum of 4 I/O modules and valve terminals with I-Port interface
(devices)
1577012
CPX-CTEL-4-M12-5POL
Cover cap
165592
ISK-M12
Inscription label holder for connection block
536593
CPX-ST-1
574321
574322
574323
574600
574601
574602
574603
574604
574605
P.BE-CPX-CTEL-DE
P.BE-CPX-CTEL-EN
P.BE-CPX-CTEL-ES
P.BE-CPX-CTEL-FR
P.BE-CPX-CTEL-IT
P.BE-CPX-CTEL-SV
CPX-CTEL master
Bus connection
M12
Connecting cable
User documentation
User documentation for CPX CTELMaster
German
English
Spanish
French
Italian
Swedish
45

Technical data Valve terminals CPV
-M-K-P-
Flow rate
CPV10: up to 400 l/min
CPV14: up to 800 l/min
Valve width
CPV10: 10 mm
CPV14: 14 mm
Voltage
24 V DC
I-Port interface for communication

between a valve terminal CPV and an
I-Port master. It activates a valve
terminal CPV with up to 16 solenoid
coils on max. 8 valve positions.
The connection to a higher-order
controller can be achieved by:
Connection to an I-Port master from
Festo (CPX-CTEL)
Direct mounting of a fieldbus node
CTEU
Connection to an IO-Link master (in
IO-Link mode)

Protocol
IO-Link
Baud rate
Maximum number of valve positions
Nominal load voltage
Intrinsic current consumption
Reverse polarity protection
Diagnostics
LED display
Connection technology
Protocol
Communication mode
Port type
Number of ports
Process data width OUT
Minimum cycle time
Electronics/sensors
Load voltage
Operating voltage
Load voltage
[bit]
[ms]
[kbps]
[V DC]
[V DC]
[V DC]
[V DC]
[mA]
[mA]
Bus-specific
Product-specific
IO-Link/I-Port
5-pin
V 1.0
COM2 (38.4 kBaud), COM3 (230 kBaud)
B
1
16
3.2
38.4/230.4
8
24
24
18 30
21.6 26.4
35
700
For operating voltage
Undervoltage in load voltage supply
1 communication status
16 valve status
Materials
Cover
Note on materials
PA
RoHS compliant

Mounting position
Ambient temperature
Storage temperature
Relative air humidity
1)
46
[C]
[C]
[%]
Any
IP65 (when fully plugged in or fitted with protective cover)
5 +50
20 +70
93 (non-condensing)

Technical data Valve terminals CPV
CPV10
CPV14
1
1
1 Earthing screw
2 I-Port interface/IO-Link

Pin
1 Earthing screw
Allocation
Description
24VEL/SEN
24VVAL/OUT
0VEL/SEN
C/Q
Data communication
0VVAL/OUT
Dimensions
Type
B1
B2
B3
H1
H2
L1
L2
L3
CPV10-GE-PT-8
CPV14-GE-PT-8
71
89
62
78
32
32.4
38.3
38.3
26.2
26.2
110
152
101.8
142
30.2
56.5
47

Accessories Valve terminals CPV
Ordering data
Type
Device ID
Weight
Part No.
Type
CPV10
0x 000410
108.5 g
1565761
CPV10-GE-PT-8
CPV14
0x 000510
200 g
1564984
CPV14-GE-PT-8
171175
FB-TA-M12-5POL
Straight plug connector M12, 5-pin (for T-adapter)
175487
SEA-M12-5GS-PG7
574321
574322
574323
I-Port bus node

Bus node with I-Port interface/IO-Link
and 8 valve positions
(maximum 8 double solenoid valves)
Connection technology for IO-Link

T-adapter M12, 5-pin for IO-Link and load voltage supply
Connecting cable
48

Technical data Valve terminals MPA-L
-M-
-K-
-P-
Flow rate
VMPA1:
VMPA14:
VMPA2:
up to 360 l/min
up to 670 l/min
up to 700 l/min
Valve width
VMPA1:
VMPA14:
VMPA2:
10 mm
14 mm
20 mm
Voltage
24 V DC
I-Port interface for communication

between a valve terminal MPA-L and
an I-Port master. It activates a valve
terminal MPA-L with up to 32 solenoid
coils on max. 32 valve positions.
The connection to a higher-order
controller can be achieved by:
Connection to an I-Port master from
Festo (CPX-CTEL)
Direct mounting of a fieldbus node
CTEU
Connection to an IO-Link master (in
IO-Link mode)

Protocol
IO-Link
Baud rate
Operating pressure
Pilot pressure
Intrinsic current consumption
Protocol
Communication mode
Port type
Number of ports
Minimum cycle time
Operating voltage
Load voltage
[bit]
[ms]
[kbps]
[bar]
[bar]
[V DC]
[mA]
[mA]

Diagnostics
LED display
IO-Link/I-Port
5-pin
V 1.0
B
1
8 32
3.2
38.4/230.4
0.9 10
38
24
30
30
Undervoltage in load voltage supply
1 communication status
Materials
End plate
Note on materials
PPA reinforced
RoHS compliant

Mounting position
Ambient temperature
Storage temperature
Corrosion resistance class CRC1)
1)
[C]
[C]
Any
5 +50
20 +40
3

Components subject to high corrosion stress. Externally visible parts with primarily functional surface requirements which are in direct contact with the surrounding industrial environment or
media such as solvents and cleaning agents.
49

Technical data Valve terminals MPA-L
VMPAL-EPL-IPO32
2
1 Status LED
2 Earthing screw

Pin
Allocation
Description
24VEL/SEN
24VVAL/OUT
0VEL/SEN
C/Q
Data communication
0VVAL/OUT
Dimensions
Type
VMPAL-EPL-IPO32
50
B1
B2
B3
B4
B5
B6
D1
D2
H1
L1
L2
L3
L4
L5
L6
L7
64.8
34.5
5.7
6.2
6.4
4.5
41.8
110
107
66.3
33.5
65
23.5
26

Accessories Valve terminals MPA-L
Ordering data
Device ID
Weight
Part No.
Type
170 g
575667
VMPAL-EPL-IPO32
171175
FB-TA-M12-5POL
Straight plug connector M12, 5-pin (for T-adapter)
175487
SEA-M12-5GS-PG7
574321
574322
574323
I-Port bus node

Bus node with I-Port interface/IO-Link and up to 32
0x 000620
valve positions (maximum 16 double solenoid valves)
Connection technology for IO-Link

T-adapter M12, 5-pin for IO-Link and load voltage supply
Connecting cable
51

Technical data Input modules CTSL
Function
Digital input modules facilitate the
connection of proximity sensors or
other 24 V DC sensors (inductive,
capacitive, etc.).
Plug connectors with double alloca
tion are separated using a DUO plug
connector or DUO cable.
Application
Input modules for 24 V DC sensor
signals
M12 connection technology
Display of the input statuses for
each input signal via an assigned
LED
Operating voltage supply 24 V DC
for all connected sensors
Diagnostic LED for short circuit/
overload of sensor supply
Labelling options on all sides with
large, hinged inscription label
Earthing plate and H-rail mounting
already integrated

Type
Electrical connection
Protocol
IO-Link
CTSL-D-16E-M8-3
Protocol
Communication mode
Port type
Number of ports
Minimum cycle time
Device ID
Baud rate
Max. no. of inputs
Current consumption at nominal operating voltage of logic circuit
Max. residual current per module
Fuse protection (short circuit)
Electrical isolation between channels
Switching level
Signal 0
Signal 1
Input debounce time
Certification
Switching logic at inputs
LED display
Bus-specific
Product-specific
52
[bit]
[ms]
[ms]
[kbps]
[V DC]
[V DC]
[mA]
[mA]
[V]
[V]
[ms]
CTSL-D-16E-M12-5
16x socket M8, 3-pin

8x socket M12, 5-pin
IO-Link/I-Port
5-pin
V 1.0
B
1
16
3.2
0x 700410
38.4/230.4
16
24
18 30
Max. 35
1.2
Internal electronic fuse protection for each group
No
5
11
0.5 (3 ms, 10 ms, 20 ms parameterisable)
IEC1131-T2
PNP (positive switching)
X20: I-Port/IO-Link
1 operating voltage
16 channel status
2 group diagnostics

Materials
Housing
Cover
Note on materials
Product weight
Dimensions
(W x L x H)
[g]
[mm]
PA reinforced
PA reinforced
RoHS compliant
250
143 x 103 x 32

Type of mounting
Ambient temperature
Storage temperature
Corrosion resistance class CRC1)
Approval certificate
1)
2)
[C]
[C]
Either via H-rail or via through-hole

IP65/IP67 (when fully plugged in or fitted with protective cap)
5 +50
20 +70
21)
C-Tick

53

CTSL-D-16E-M8-3
4
3
2
1
2
3
4
5
7

Pin
Allocation
Description
24VEL/SEN
0VEL/SEN
C/Q
Data communication
Pin allocation Sensor connections CTSL-D-16E-M8-3

Pin allocation
54
Earth terminal
Status LED for power supply (PS)
Status LED for I-Port (X20)
Status-LEDs for inputs (status
display, green)
6 Status LED (group) for short

circuit/overload of sensor
supply (red)
7 Fixture for inscription label
holder ASCF-H-E2
8 Sensor connections
(1 input per socket)
Pin
Allocation
Description
24V
Operating voltage 24 V
0V
Ix*
Sensor signal
Ix = Input x

CTSL-D-16E-M12-5
4
7
8
1
2
3
4
5
7

Pin
Allocation
Description
24VEL/SEN
0VEL/SEN
C/Q
Data communication
Pin allocation Sensor connections CTSL-D-16E-M12-5

Pin allocation
Earth terminal
Status LED for power supply (PS)
Status LED for I-Port (X20)
Status-LEDs for inputs (status
display, green)
6 Status LED (group) for short

circuit/overload of sensor
supply (red)
7 Fixture for inscription label
holder ASCF-H-E2
8 Sensor connections
(2 inputs per socket)
Pin
Allocation
Description
24V
Ix+1*
Sensor signal
0V
Ix*
Sensor signal
FE
Functional earth
Ix = Input x
55

Dimensions
CTSL-D-16E-M8-3
CTSL-D-16E-M12-5
Type
B1
B2
B3
B4
B5
D1
D2
H1
H2
L1
L2
L3
T1
CTSL-D-16E
103
87
35.5
32.8
4.3
32
9.4
143
127
3.5
56

Accessories Input modules CTSL
Ordering data
Description
Part No.
Type
16 sensor connections M8, 3-pin, single allocation
1387363
CTSL-D-16E-M8-3
8 sensor connections M12, 5-pin, double allocation
1387359
CTSL-D-16E-M12-5
5-pin, PG7
4-pin, PG7
4-pin, 2.5 mm2 O.D.
3-pin, solderable
3-pin, screw-in
4-pin
175487
18666
192008
18696
192009
18779
SEA-M12-5GS-PG7
SEA-GS-7
SEA-4GS-7-2,5
SEA-GS-M8
SEA-3GS-M8-S
SEA-GS-11-DUO
Input modules
Plug connector
Straight plug connector, M12
Straight plug connector, M8

Plug connector for 2 cables, M12, PG11
5-pin
192010
SEA-5GS-11-DUO
Push-in T-connector
2x socket, M12, 5-pin

1x plug connector M12,
4-pin
541596
NEDU-M12D5-M12T4
DUO cable, 1x straight plug connector M12
2x straight socket M8
1x straight socket M8 and
1x angled socket M8
2x angled socket M8
2.5 m
5.0 m
0.5 m
1m
2.5 m
5m
18685
18688
KM12-DUO-M8-GDGD
KM12-DUO-M8-GDWD
18687
539052
539052
539052
539052
539052
539052
KM12-DUO-M8-WDWD
NEBU-M12G4-K-2.5-M12G4 1
NEBU-M12G4-K-5-M12G4 1
NEBU-M8G3-K-0.5-M8G31
NEBU-M8G3-K-2.5-M8G31
574321
574322
574323
547473
ASCF-H-E2
Connecting cables
Connecting cable, M12, 4-pin, straight plug

connector-straight socket
Connecting cable, M8, 3-pin, straight plug connectorstraight socket
Inscription label holder

Inscription label holders for EL modules, bag of 10
1)
Modular product, more information Internet: nebu
57

Example of a valve terminal VTUG with I-Port interface
Dimensions Example of a valve terminal with I-Port interface,

size 10
1 Ports 1, 3 and 5: Gx (at both

ends)
3 Ports 12/14: M5 (at both ends)
4 Ports 82/84: M5 (at both ends)
58
5 CTEU CANopen
6 For mounting valves/blanking
plates/supply plates on
manifold block: M2
7 Blanking plate
8 Supply plate, ports 1, 3 and 5:
M7
9 H-rail mounting
aJ Inscription label holder

Example of a valve terminal VTUG with I-Port interface
Type
VABM
Type
No. of
valve positions
B1
B2
B3
B4
B5
B6
B7
B8
Size 10
D1
4-24
91.5
54
52.4
41.5
25.6
9.8
16
17.7
4.5
No. of
valve positions H9
H11
H12
L4
5.5
54.8
4.8
10.5
Size 10
L5
H3
H4
H5
H6
H7
H8
67
56.1
54.1
15.2
11.5
15.5
L6
L7
L8
L9
L10
2.5
4.5
36
20
42.5
4-24
Type
No. of
valve positions
L1
Size 10
L2
L3
4
5
6
7
8
9
10
12
16
20
24
103
113.5
124
134.5
145
155.5
166
187
229
271
313
94
104.5
115
125.5
136
146.5
157
178
220
262
304
31.5
42
52.5
63
73.5
84
94.5
115.5
157.5
199.5
241.5
57.3
H2
VABM
VABM
12.4
H10
H1
102.3 77.1
59

Cteu en

Uploaded by

Copyright:

Available Formats

Cteu en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cteu en

Uploaded by

Copyright:

Available Formats

Fieldbus modules CTEU/Installation system CTEL

Fieldbus modules CTEU/Installation system CTEL

Wide range of applications thanks

CTEU for the universal use of valve

The following protocols are currently

Online via: www.festo.com

Valve terminal configurator

only need to be placed on the valve

the type of compressed air supply.

Tested for electrical function

Subject to change 2014/12

Fieldbus modules CTEU/Installation system CTEL

2014/12 Subject to change

Fieldbus modules CTEU/Installation system CTEL

The following protocols are supported

A second valve terminal can be con

System overview, example

Node CTEU (I-Port master) on

CPX terminal with bus node

Valve terminal CPV with

Pneumatic drive with sensor

Communication with higher-order

Use a fieldbus node CTEU com

Subject to change 2014/12

Fieldbus modules CTEU/Installation system CTEL

VTUB-12 Valve terminal

CPX with control block

Connecting cable NEBU

Cable socket NEFU-X

Power supply unit SVG for

2014/12 Subject to change

Fieldbus modules CTEU/Installation system CTEL

With I-Port interface, for connecting max. 35 valves

For bus node

Subject to change 2014/12

Fieldbus modules CTEU/Installation system CTEL

Diagnostic messages via the fieldbus

2014/12 Subject to change

1 Diagnostics via fieldbus

Fieldbus modules CTEU/Installation system CTEL

The operating voltages are required

The power supplies do not have a

Example power supply concept CTEU with valve terminal VTUG

Subject to change 2014/12

Fieldbus modules CTEU/Installation system CTEL

2014/12 Subject to change

Fieldbus modules CTEU/Installation system CTEL

The electrical supply/transmission

The following protocols are

General technical data

Pin allocation I-Port interface/IO-Link

Operating voltage supply (electronics, sensors/inputs)

Load voltage supply (valves/outputs)

Operating voltage supply (electronics, sensors/inputs)

Load voltage supply (valves/outputs)

Subject to change 2014/12

Fieldbus modules CTEU/Installation system CTEL

Outlet on the side

Outlet on the side