Surface Energy Testing

Surface Energy
Testing
Dyne Pens and Test Fluids

DYNE TEST PENS: (Valve Tip Applicator type) Formulated to ISO 8296.
Our Dyne Testing Pens are the valve tip applicator type and not the Felt Tip
Pen type. The Valve Tip Applicator principle is simple: keep the testing part of
the pen away from the fluid storage part of the pen (in other words, no wicking
from the substrate). By pressing the pen tip firmly down, the valve is opened
and fresh fluid floods the tip; thus flushing it clean, this allows the tester to
lightly pass over the sample to accurately determine the Dyne level. The
disposable pens have a fluid capacity of 15ml and are available in 1 Dyne
(mN/m) increments from 30 to 70 mN/m.
Standard Pack 6 pens: 36, 40, 44, 48, 52 & 56 mN/m in pen box.
SelfSelect Pack 6 pens: Select any 6 pens between 30 & 60 mN/m in pen box.
ConverterPack 6 pens: 38, 38, 42, 42, 44 & 44 mN/m in pen box.
BlownfilmPack 6 pens: 34, 34, 38, 38, 42 & 42 mN/m in pen box.
Individual pens Select from range 30 70.
DYNE QUICK TEST 38-40 PENS (Red ink)

Use a slight pressure to draw the pen tip across the surface to be tested. If the
ink lines shrink or bead within 1-2 seconds then the surface is NOT treated to a
level of 38 Dynes. If the ink lines remain as marked and do not shrink then the
test sample surface IS treated to a level of 38 Dynes or higher.
DyneQuickTest Pens only available in 38-40 (Dynes) mN/m.
DYNE TEST SOLUTIONS

Type A: Blue Formulated to ISO8296
Supplied in 20ml bottles with integral brush applicator and 100ml bottles with
dropper cap. Containing: formamide, 2-ethoxyethanol & dye. Not suitable for
use on soft PVC. Available values: 30 to 72mN/m (Dynes).
Type B: Yellow - (NON-TOXIC)
Supplied in 20ml bottles. Ethanol based. Not suitable for use on Polypropylene.
Available values: 30 - 72mN/m (Dynes).
Kits available
- Standard kit of 6 bottles in carrying case: 36, 40, 44, 48, 52 & 56 mN/m.
- Self Select Kit of 6 bottles in carrying case.
- Individual bottles.
- Cotton Applicator Swabs ( to ISO 8296, ASTM D2578 & TAPPI T-698 test
methods).
DYNE TEST APPLICATOR SWABS

Compliant with ISO8296
Cotton Applicator Swabs ( to ISO 8296, ASTM D2578 & TAPPI T-698 test
methods).
150mm long shaft: ensures your hand is kept well away from the test fluid and
the substrate to be tested.
Binder free: ensures that the binders used in common cotton buds do not
contaminate the test fluid or invalidate test results.
Glue free: ensures that the glues used in common cotton buds do not
contaminate the test fluid or invalidate test results.
Produced in an ISO9001-2000 registered facility to assure consistent high
quality.
Contact Angle Measurement

DyneX CAM and CAM Lite - Contact Angle Meters
Compact CCD camera based instruments for measuring contact angles of
liquids on solids and Free Surface Energy of solids. FireWire interface to PC
makes the instrument extremely fast, yet easy to install. Powerful drop shape
analysis software makes the measurements user independent and error free,
ensuring reproducible results. The Contact Angle Meter is an accurate, simple,
and easy to use, yet extremely powerful instrument. Designed for industrial,
QC, education and R&D applications these instruments set a new standard in
contact angle measuring technology.
Applications
For highly accurate and easy measurements of:
wettability
contact angles
surface free energy
absorption
adsorption
spreading
cleanliness
surface heterogeneity
surface tension*
interfacial tension*
*requires extended software for DyneX Lite
Technical specifications:
DyneX CAM Lite
DyneX CAM
Measuring range
0...180, 0.01...999 mN/m
0...180, 0.01...999 mN/m
Accuracy
0.1, 0.01 mN/m
0.1, 0.01 mN/m
Maximum sample size
W unlimited x L 200 x H
50mm (with stage)
W unlimited x L 180 x H
225mm (H 95mm with stage)
Frame interval
100 ms(16 ... 1000 ms with

extended software)
2...1000 ms
Resolution
512 x 480 pixels
512 x 480 pixels
Max. measuring speed
10 frames/sec (60 frames/sec

with extended software)
60 frames/sec (420 frames/

sec with high speed camera)
Camera
Firewire digital camera
Firewire digital camera with

zoom optics
Light source
LED based background

lighting
LED based background

lighting
Dimensions
H 310mm, W 130mm,
L 495mm
H 590mm, W 200mm,
L 740mm
Weight (basic frame)
5 Kg
7.3 Kg
Power supply
100...240 VAC
100...240 VAC
Frequency
50...60 Hz
50...60 Hz
Drawdown Platforms,
Rods and Applicators
DyneX Drawdown Platform
Full width magnetic clamp allows precise sample positioning with secure grip.
12.7mm thick float glass platform large enough for direct A to B comparisons
or evaluation of machine caused treatment variations. 305mm x 305mm
smoothing pad with closely controlled compressibility is engineered to promote
uniform fluid distribution with minimal squirm. Each unit is meticulously
inspected to assure flatness. Ideal for use with DyneX applicators. Five
pre-adjusted shock absorbing levelling feet and surface mounted spirit level
ensure precise levelling and firm footing. Liquid crystal thermometer is accurate
to better than 1C.
Metering Rod Selection Chart
Thickness(1) Coverage Wet Film
Weight(2)
Rod
#
Microns
m2/l
g/m2
3.8
263
3.8
7.6
131
7.6
10.2
98.4
10.2
12.7
78.7
12.7
15.2
65.6
15.2
17.8
56.4
17.8
20.3
49.2
20.3
22.9
43.7
22.9
10
25.4
39.4
25.4
12
30.5
32.8
30.5
15
38.1
26.3
38.1
18
45.7
21.9
45.7
22
55.9
17.9
55.9
24
60.3
16.1
60.3
30
76.2
13.1
76.2
36
91.4
10.9
91.4
42
107
9.2
107
50
127
7.9
127
80
200
4.9
203
100
254
3.9
254
(1)
1 mm = 1000 microns. Thickness varies

somewhat, notably for high viscosity
liquids and small wire rods. (2) g/m2
assumes 1 g/cm3
DyneX Metering Rods

Applies a highly uniform wet film coating.These wire-wound metering rods,
when used on a precision surface such as the DyneX Drawdown Platform,
will apply a highly uniform wet film thickness, which is ideal for Dyne testing.
These rods, widely known as Mayer Rods or drawdown bars are fabricated
from 303 stainless steel; the wire winding is 304 stainless steel. The 400mm
long rod has 305mm of wire wound on centre. Rods are available in 6.3mm
and 12.7mm diameters.
These lab rods can be used either to test two coatings simultaneously, or for
full width substrate evaluations using one test liquid. Economical and easy to
use; simple clean-up with water, alcohol, appropriate solvent and low lint cloths.
With the use of such non-abrasive cleaners, metering rods can be repeatedly
reused.
DyneX Applicator
With a Teflon coated surface it is ideal for Dyne testing no attraction to, or
contamination from the applicator affects test results. Remarkably fast and
easy clean-up saves time and cleaning supplies.
The DyneX applicator measures only 13 x 13 x 64mm. A precision ground
gate, 38mm wide, is centered on each of the four edges. This restricted
passage channels the flow of the Dyne fluid through the gate whilst limiting the
wet film thickness applied to a maximum of only 12.5 microns.
This tool can produce high quality drawdowns in a confined area, making
direct benchtop testing a reality. For best results, we strongly suggest use on
a DyneX drawdown platform. All four gates are precision ground to the same
clearance to facilitate quicker test-to-test turnaround, and to provide the longest
service life. Packed in a cushioned protective container.
To perform the Dyne test with a DyneX applicator, first apply a short bead of
surface tension test fluid from a dropper bottle directly to the sample surface.
As soon as possible, the applicator is then drawn down over this bead,
spreading it over the surface. Determination of Dyne level by wetting is
then performed to a standardised test procedure.
Dyne Testing Ltd.

Newton House, 5 Parkside Court, Greenhough Road,
Lichfield, Staffordshire, WS13 7FE, United Kingdom
Phone: +44 (0) 1543 411 460
Fax:
+44 (0) 1543 415 140
E-mail:
Web:
sales@dynetesting.com
www.dynetesting.com

Surface Energy Testing

Uploaded by

Copyright:

Available Formats

Surface Energy Testing

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Surface Energy Testing

Uploaded by

Copyright:

Available Formats

What are Dyne pens and how do they work?

What are Dyne pens and how do they work?

What is the difference between DyneX CAM and DyneX CAM Lite contact angle meters?

What is the difference between DyneX CAM and DyneX CAM Lite contact angle meters?

Surface Energy

Dyne Pens and Test Fluids

DYNE QUICK TEST 38-40 PENS (Red ink)

DYNE TEST SOLUTIONS

DYNE TEST APPLICATOR SWABS

Contact Angle Measurement

0...180, 0.01...999 mN/m

0...180, 0.01...999 mN/m

0.1, 0.01 mN/m

0.1, 0.01 mN/m

Maximum sample size

100 ms(16 ... 1000 ms with

512 x 480 pixels

512 x 480 pixels

Max. measuring speed

10 frames/sec (60 frames/sec

60 frames/sec (420 frames/

Firewire digital camera

Firewire digital camera with

LED based background

LED based background

Weight (basic frame)

1 mm = 1000 microns. Thickness varies

DyneX Metering Rods

Dyne Testing Ltd.

You might also like