GSM Controlled Wireless Robotic System

International Journal of Scientific Research Engineering & Technology (IJSRET), ISSN 2278 0882
Volume 4, Issue 8, August 2015
GSM CONTROLLED WIRELESS ROBOTIC SYSTEM

Manisha Chaudhary, Prof. Nishant, Dr. Noor Danish
Student, EEE Dept, Arni University, Kangra
Assistant Prof. of EEE Dept, Arni University, Kangra
HOD of EEE Dept., Arni University, Kangra
ABSTRACT
GSM Controlled Wireless Robot is automatic robots
which capable of receiving a set of command
instructions in the form of Short message service and
performs the necessary actions. We will be using a
dedicated modem/mobile at the receiver module i.e. with
the robot itself and send the commands using SMS
service as per the required actions. Although, the
appearance and capabilities of robot vary vastly, all
robots share the feature of a mechanical, movables
structure under some form of control. The control of
robot involves three distant phases: perception,
processing, action. Generally, the preceptors are sensors
mounted on the robot, processing is done by the on
board microcontroller and the task is performed using
motors or with some other actuators.
direction it has to move which is the complete

responsibility of the controller to take those intelligent
decisions.
II. BLOCK DIAGRAM

The block diagram of the GSM based automatic robotic
system has been shown in fig. 2.That robotic system
technology will totally base upon the DTMF (Dual-tone
multi frequency) technology. The block diagram
consider microcontroller, DTMF decoder, motor drive
that is consider for left and right movement of the
system. Mobile phone is use like as a remote, which is
use for movements of the drive.
I. INTRODUCTION
GSM stands for Global System for Mobile
Communications. GSM projects are based on one of the
emerging technology of the century. It deals with design
of a stand-alone embedded system that can monitor and
control several devices remotely irrespective of distance
limitations. Generally sending and receiving SMS is the
concept followed in embedded domain. The system has
two parts, namely; hardware and software. The hardware
architecture consists of a stand-alone embedded system
using a 8-bit microcontroller, several type of interface
and driver circuits. The system software driver is
developed using an interactive C programming
language. The mobile unit which is dedicated at the
robot is interfaced with an intellectual device called
Micro controller so that it takes the responsibility of
reading the received commands in the form of SMS
from the mobile unit and perform the corresponding
predefined tasks such as move front or back, left or right
etc. The micro controller is also interfaced with few DC
motors in order to move the robot in different directions.
The ON and OFF of the DC motors depends on the
Fig.1 Block diagram of GSM Technology

By using that technology we can easily operate and
control the considered drive. Basically this technology is
consider for carrying the material from anywhere, but
condition is this, the operator mobile and the second
following mobile, these both should be remain in contact
www.ijsret.org
864
or in range. The block diagram generates a robotic

device which will be controlled by the operated mobile.
That is such type of robotic system can move the motor
left, right, up or down side, which move anywhere at any
time. Wireless communication is main important thing
that is used here. Two mobile are interconnected here:
first mobile is operated by an operator and second
mobile which is connected with first mobile, which
follows the first mobile order. First mobile remain in
operator hands and the second mobile follows the order
provided by first mobile. And camera is provided on the
front side of robotic. Whole technology based upon the
MIN: Mobile identification number and used
microcontroller.
electronic technicians to create electronic schematics and

electronic prints for manufacturing printed circuit
boards. The name OrCAD is a portmanteau, reflecting
the company and its software's origins: Oregon + CAD.
IV. RESULT
The robotic system detects the signal from the operator
handle mobile through GPS receiver system. The
operator handle mobile operate the mobile and provide
the direction and the second mobile which is attach on
the robot it achieve the signal and move on according the
provided direction. The robot is mainly move in the
given direction which is provided by user through SMS.
The system based upon the GSM technology.
III. TECHNOLOGY USED

III. 1) DTMF keypad Technology
The DTMF keypad technology based upon keypad that
have an additional column for four now-defunct menu
selector keys. When used to dial a telephone number,
press a single key will produce a pitch consisting of two
simultaneous pure tone sinusoidal frequencies. The row
in which the key appears determines the low frequency,
and the column determines the high frequency. For
example, pressing the key will result in a sound
composed of both a 697 and a 1209 hertz (Hz)
tone. The original keypad has levers inside, so each
button activated two contacts. The multiple tones are the
reason for calling the system multi frequency. These
tones are then decoded by the switching center to
determine which key was pressed.
Fig.3 Experimental view

This is the experimental work of the GSM robotic
technology. The used camera is very necessary thing
because the front attachment of the camera helps the
robots for move in much batter way. The usage of
camera is consider for monitoring purpose.
V.CONCLUSION
Fig. 2 Telephone keypad

III.2) Software used
OrCAD is a proprietary software tool suite used
primarily for electronic design automation. The software
is used mainly by electronic design engineers and
This paper propose for enhance the safety. The GSM

technology is deals with mobile it depends upon DTMF
technology. That technology is mobile based, its
interfaces offer more promises for wide variety of
applications. This technology is very reliable
adaptability and efficient. GSM applications are very
popular for their applications. Specially this technology
is consider for coal carrying from the core of the earth.
www.ijsret.org
865
REFRENCES
[1] Alkiviadius Yianna Roulias et al, Evaluation
OfHeader Compression Schemes For IP-Based Wireless
Access Systems, IEEE Wireless Communication,
Vol12,No.1, February 2004, pp 54-59.
[2]. Ze-Nian Li and Mark S. Drew, Fundamentals of
Multimedia, Pearson Education.
[3]. John F.Koegel Buford, Multimedia Systems,
Pearson Education.
[4].Muhammad Ali et al, Multimedia Multicast/
Broadcast Services In 3G/4G Network, IEEE
Communication, Vol. 42, No.1, February 2004, pp 106113.
[5]. Simone Leggiv et al,Achieving Seamless Mobility
in IP - Based Radio Access Network, IEEE Wireless
Communication, Vol 12,No.1, February 2004, pp 54-59.
[6] Nethawk GSM Analyzer, www.nethawk.fi
[7] D. Newman, Voice over Wireless LAN, Network
World, January 2004.
www.ijsret.org
866

GSM Controlled Wireless Robotic System

Uploaded by

Copyright:

Available Formats

GSM Controlled Wireless Robotic System

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GSM Controlled Wireless Robotic System

Uploaded by

Copyright:

Available Formats

International Journal of Scientific Research Engineering & Technology (IJSRET), ISSN 2278 0882

Volume 4, Issue 8, August 2015

GSM CONTROLLED WIRELESS ROBOTIC SYSTEM

direction it has to move which is the complete

II. BLOCK DIAGRAM

Fig.1 Block diagram of GSM Technology

or in range. The block diagram generates a robotic

electronic technicians to create electronic schematics and

III. TECHNOLOGY USED

Fig.3 Experimental view

Fig. 2 Telephone keypad

This paper propose for enhance the safety. The GSM

You might also like