Conbextra EP10TG

Conbextra EP10TG
constructive solutions
High Strength Epoxy Resin Grout

Uses
Properties
Provides a free flowing grout, for use where physical
Compressive strength
57 N/mm2 @ 1 day
properties and chemical resistance of the hardened grout
66 N/mm2 @ 3 days
are of utmost importance. It is suitable for a wide range of
83 N/mm2 @ 7 days
heavy duty applications including;
Flexural strength
Underplate grouting to substantial structural elements.
Base plate grouting in dynamic load situations such
Tensile strength
as turbines and other reciprocating machinery.
Heavy industrial applications in steelworks, refineries
26 N/mm2 @ 7 days
Density
Approximately 1050 kg/m
Pot life
60 min. @ 20C
45 min. @ 30C
chemical plants and electroplating works. Structural
63 N/mm2 @ 7 days
infill where very high strength is required.
Specification Clauses
Rail track applications, to support heavy cranes, or on
Where shown on the contract documents, the epoxy grout
transporter rails.
shall be Conbextra EP10TG supplied by Fosroc. It shall

provide good general chemical resistance, and a 7 day
Advantages
compressive strength of at least 75 N/mm .
Excellent durability - high compressive, flexural and
Instructions for Use
tensile strengths ensure a long working life.
Preparation
Cost effective - high early strength gain promotes

minimum downtime and early commissioning of plant.
Underplate grouting
User friendly - simple, full pack mixing to ensure that
The unrestrained surface area of the grout must be kept to
the performance characteristics are achieved.
a minimum. Generally, the gap between the perimeter

formwork and the plate edge should not exceed 75 mm on
Versatile - suitable for a wide range of loading
the pouring side and 25 mm on the opposite side.
situations including repetitive dynamic loads.
Formwork on the flank sides should be kept tight to the
Excellent
in
service
performance
non-shrink
plate edge. Air pressure relief holes should be provided to
capability ensures full surface to surface contact.
allow venting of any isolated high spots.
Description
Formwork
Conbextra EP10TG is a solvent free epoxy resin grout
The formwork should be constructed to be leak proof as
designed for grouting of gap widths of 0.25 10 mm. It is
Conbextra EP10TG is a free flow grout. This can be
an all liquid system consisting of base and hardener. The
achieved by using foam rubber strip or mastic sealant
components are supplied in the correct mix proportions
beneath the constructed formwork and between joints. For
designed for whole pack mixing on site.
free flow grout conditions, it is essential to provide a
Technical Support
hydrostatic head of grout. To achieve this a feeding

hopper should be used - please consult your local Fosroc
Fosroc offers a comprehensive range of high quality, high
office for more details.
performance construction products. In addition, Fosroc

offers a worldwide technical support and on-site service to
specifiers, end-users and contractors.
Page 1
Conbextra EP10TG
Foundation surface
Limitations
This must be free from oil, grease, or any loosely adherent
Grouts should not be placed in any unrestrained situation,
material. If the concrete surface is defective or has laitance,
i.e. base plate plinths, etc. Failure to comply may lead to
it must be cut back to a sound base. Bolt holes or fixing
crack development in the grout.
pockets must be blown clean of any dirt or debris.
Estimating
Base plate
Supply
If delay is likely before placing steel base plates, it is

recommended that the underside and edges are coated with
Nitoprime 25* to prevent rust formation and ensure bonding
with the Conbextra EP10TG grout. All metal surfaces should
be cleaned to a bright finish in accordance with Swedish
Conbextra EP10TG
5 litre / set
Nitoprime 25
1 & 5 litre pack
Fosroc Solvent 102
5 litre packs
4.0 to 5.0 m /litre
Coverage
Standard SA 2 or equal. Nitoprime 25 can be applied

directly onto newly cleaned steel surfaces even if they are
Nitoprime 25
damp.
Storage
Mixing
When
The entire contents of the hardener can should be poured
Conbextra EP10TG will have a shelf life of 12 months
into the base container and mixed for 2-3 minutes or until
Precautions
stored
in
warehouse
conditions
below 35C,
uniform colour is achieved. Once mixed, the material must

Health and Safety
be used within the specified pot life (see under Properties).

Note: Immediately prior to placement, all surfaces must be
Some people are sensitive to epoxy resin so gloves and a

barrier cream such as Kerodex 71, Rozalex 9, Debba Wet
dry.
Work or similar should be used when handling these

Placing
products. If contact with the resin occurs, it must be
Ensure that the grout can be placed within its pot life.
removed before it hardens with a resin removing cream
Continuous grout flow is essential. Sufficient grout must be
such as Kerocleanse 22 or Rozalex 42. Follow by washing
available prior to starting and the time taken to pour a batch
with soap and water. Do but should accidental eye
must be regulated to the time taken to prepare the next one.
contamination occur, wash thoroughly with plenty of clean
Pouring should be from one side of the void to eliminate air
water and seek medical treatment immediately.
entrapment. The hydrostatic head must be maintained at all
Fire
times so that a continuous grout front is achieved.

Nitoprime 25 and Fosroc Solvent 102 are flammable.
Cleaning
Flash points
All tools and equipment should be cleaned immediately after
use with Fosroc Solvent 102.
Nitoprime 25
39C
Fosroc Solvent 102
33C
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation of information given by it.
PT.FOSROC
Indonesia
Jl.Akasia II Blok A8 No.1
Delta Silicon Industrial Park
Lippo Cikarang
Bekasi 17550
Indonesia
www.fosroc.com
+62 21 897 2103

+62 22 727 5647
+62 31 854 9704
+62 21 897 2107

+62 22 727 5649
+62 31 894 9845
Page 2
Indonesia@Fosroc.com
IND/1208/EA

Conbextra EP10TG

Uploaded by

Copyright:

Available Formats

Conbextra EP10TG

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Conbextra EP10TG

Uploaded by

Copyright:

Available Formats

Conbextra EP10TG

High Strength Epoxy Resin Grout

Provides a free flowing grout, for use where physical

properties and chemical resistance of the hardened grout

are of utmost importance. It is suitable for a wide range of

heavy duty applications including;

Underplate grouting to substantial structural elements.

Base plate grouting in dynamic load situations such

as turbines and other reciprocating machinery.

Heavy industrial applications in steelworks, refineries

Approximately 1050 kg/m

chemical plants and electroplating works. Structural

infill where very high strength is required.

Rail track applications, to support heavy cranes, or on

Where shown on the contract documents, the epoxy grout

shall be Conbextra EP10TG supplied by Fosroc. It shall

compressive strength of at least 75 N/mm .

Excellent durability - high compressive, flexural and

Instructions for Use

tensile strengths ensure a long working life.

Cost effective - high early strength gain promotes

User friendly - simple, full pack mixing to ensure that

The unrestrained surface area of the grout must be kept to

the performance characteristics are achieved.

a minimum. Generally, the gap between the perimeter

Versatile - suitable for a wide range of loading

the pouring side and 25 mm on the opposite side.

situations including repetitive dynamic loads.

Formwork on the flank sides should be kept tight to the

plate edge. Air pressure relief holes should be provided to

capability ensures full surface to surface contact.

allow venting of any isolated high spots.

Conbextra EP10TG is a solvent free epoxy resin grout

The formwork should be constructed to be leak proof as

designed for grouting of gap widths of 0.25 10 mm. It is

Conbextra EP10TG is a free flow grout. This can be

an all liquid system consisting of base and hardener. The

achieved by using foam rubber strip or mastic sealant

components are supplied in the correct mix proportions

beneath the constructed formwork and between joints. For

designed for whole pack mixing on site.

free flow grout conditions, it is essential to provide a

hydrostatic head of grout. To achieve this a feeding

Fosroc offers a comprehensive range of high quality, high

office for more details.

performance construction products. In addition, Fosroc

This must be free from oil, grease, or any loosely adherent

Grouts should not be placed in any unrestrained situation,

material. If the concrete surface is defective or has laitance,

i.e. base plate plinths, etc. Failure to comply may lead to

it must be cut back to a sound base. Bolt holes or fixing

crack development in the grout.

pockets must be blown clean of any dirt or debris.

If delay is likely before placing steel base plates, it is

1 & 5 litre pack

Fosroc Solvent 102

4.0 to 5.0 m /litre

Standard SA 2 or equal. Nitoprime 25 can be applied

The entire contents of the hardener can should be poured