Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
268 views

Lecture 9 PDF

This document discusses different types of interchanges used for highways. It describes interchanges as grade-separated intersections that allow traffic to move between intersecting roadways on different levels. The main types discussed are three-leg interchanges like trumpet and direct configurations, four-leg interchanges like diamond, cloverleaf, and directional, and the characteristics of each. Key factors in interchange design include traffic patterns, land availability, and environmental impacts.

Uploaded by

Nazar Shafiq
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
268 views

Lecture 9 PDF

This document discusses different types of interchanges used for highways. It describes interchanges as grade-separated intersections that allow traffic to move between intersecting roadways on different levels. The main types discussed are three-leg interchanges like trumpet and direct configurations, four-leg interchanges like diamond, cloverleaf, and directional, and the characteristics of each. Key factors in interchange design include traffic patterns, land availability, and environmental impacts.

Uploaded by

Nazar Shafiq
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Highway Geometric Design

3rd Stage

Interchanges
Interchanges (grade separated intersection)
An interchange is defined as a system of interconnecting roadways in
conjunction with one or more grade separations that provides for the
movement of traffic between two or more roadways or highways on
different levels.
Interchanges are utilized on freeways and expressways, where access
control is important. They are used on other types of facilities only
where crossing and turning traffic cannot be accommodated by a
normal at-grade intersection.

Interchanges
An interchange can be a useful an adaptable solution for many
intersection problems either by reducing existing traffic bottlenecks or
by improving safety. However, many factors that should be considered
during interchange design:

1. Topography of the site


2. Traffic characteristics
3. Land availability

4. Impact on environment
5. Economic factors

Interchanges
A grade separation refers to the crossing of two roadways by a physical
separation so that neither roadway interferes with the other. An interchange is
a grade separation with connecting roadways (ramps, loops, or connections)
that move traffic between the intersecting highways.
Classifications. Interchanges are classified in a general way, according to the
number of approach roadways or intersection legs. The following
subsections include a brief description and some of the advantages and
disadvantages of each of the following types of interchanges:
1. Three leg interchanges
2. Four leg interchanges

Interchanges

Three leg interchanges:


Three-leg interchanges or (T and Y interchanges) can take any of several forms,
although all of the forms provide connections for the three intersecting highways.
Three-leg interchanges should be used only after careful consideration because
expansion to include a fourth leg is usually very difficult.
Trumpet. The most widely used 3-leg interchange is the trumpet type. This type of
interchange is particularly suitable for the connection of a major facility and a
freeway. Preference should be given to the major turning movements so that the
directional roadway handles higher traffic volume and the loop the lower traffic
volume.

Interchanges

Direct. High-type directional three-leg interchanges are those in which all


movements are provided without the use of loops. These interchanges should be
used only where all movements are large. They contain more than one structure or,
alternatively, a three-level structure.

Interchanges
This design:

accommodates the T-intersection flow of traffic at the junction of two roadways.


allows for traffic on a secondary two-way street to merge onto a multiple lane
roadway.

Interchanges
Four Leg Interchanges
Four-leg interchanges can take a wide variety of forms. The choice of interchange
type is generally established after careful consideration of dominant traffic patterns
and volumes and system considerations. The three primary types of four-leg
interchanges are as follows:
1. Diamond Interchanges
2. Cloverleaf Interchanges
3. Directional Interchange

Interchanges
1- Diamond Interchanges
The diamond interchange is the most common interchange, especially in urban
areas, since it requires less area than any other type. The diamond interchange is
used almost exclusively for major-minor crossings since left-turn movements are
made at-grade across conflicting traffic on the minor road. Separation between
frontage road intersections in diamond interchanges in urban or suburban
conditions should be 300 ft [90 m] as a minimum.

Interchanges
Typical Diamond Interchanges.
The diamond interchange may have several different configurations

Interchanges
Single point diamond.

A special type of freeway-to-arterial


interchange has received attention during
recent years.
In this type of interchange, the freeway
mainlines may go either over or under the
crossing arterial and the turn movements
occur at-grade on the arterial.

This type of interchange has application


only in specialized locations.

Interchanges
This design allows:

for the interchange of a major roadway with a secondary dual or multiple lane roadway.

Interchanges
2-Cloverleaf Interchanges
Cloverleaf interchanges are very common in the world. These types of interchanges
were popular in the early era of freeway construction, but are usually no longer
considered preferable for freeway to freeway movement, especially when
interchange volumes are high.
Cloverleaf should not be used where left-turn volumes are high (exceed 1200
vehicle/hr) since loop ramps are limited to one lane of operation and have restricted
operating speeds.

Interchanges

Full cloverleaf. The four-quadrant, full cloverleaf, eliminates all leftturn conflicts through construction of a two-level interchange.

Interchanges

Primary disadvantages of the cloverleaf design include the following:


1. large right-of-way requirements
2. capacity restrictions of loops, especially if truck volumes are
significant
3. short weaving length between loops
4. trucks have difficulty with weaves and acceleration
When used, cloverleaf designs should include collector-distributor roads
to provide more satisfactory operations as further noted in the section on
Collector-Distributor Roads.

Interchanges
The cloverleaf design has serious objections:
1. Takes large area

2. Vehicles desire to make a left turn must make a


270turn and travel will be on sharp curves and
steep slope
3. Vehicles leaving the curved loop in one quadrant
must weave through those entering the adjacent
loop from the through roadway. Where weaving
volumes are high, the weaving section must be
long.

Interchanges
This design

allows for the interchange of two expressways or major roadways.


has shared entrance and exit weave lanes.

Interchanges

Partial cloverleaf (semi-cloverleaf) interchanges


A cloverleaf without ramps in all four quadrants, is sometimes used when site
controls (such as railroads or streams running parallel to the crossroad) limit the
number of loops and/or the traffic pattern is such that the left-turn conflicts caused
by the absence of one or more loops are within tolerable limits.

Interchanges
3- Directional Interchanges
Interchanges that use direct or semi-direct connections
for one or more left-turn movements are called
directional interchanges. When all turning
movements travel on direct or semi-direct ramps or
direct connections, the interchange is referred to as
fully directional.
These connections are used for important turning
movements instead of loops for the following purposes:
1.

to reduce travel distance

2.

increase speed and capacity

3.

reduce weaving

4.

avoid loss of direction in traversing a loop.

Fully directional interchanges are usually justified at


the intersection of two freeways.

You might also like