Appendix W 09-11-2013
Appendix W 09-11-2013
Appendix W 09-11-2013
APPENDIX W
APPENDIX W
WELDING OF TANK CAR
TANKS
CONTENTS
Paragraph
1.0
Subject
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III448
1.1
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III448
1.2
1.3
1.4
2.0
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III448
3.0
3.1
3.2
3.3
4.0
4.1
Welds Other than Tank Shell JointsAttachments Welded Directly to the Tank Shell. . . . . . . . . . C-III451
Test Plate Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III452
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III452
4.2
4.3
4.4
4.5
4.6
4.7
5.0
5.1
5.2
5.3
5.4
5.5
6.0
6.1
6.2
6.3
6.4
7.0
10/2007
C-III [M-1002] 1
APPENDIX W
M-1002
7.1
7.2
8.0
8.1
8.2
10/2007
Paragraph
9.0
Subject
Page
Impact, Corrosion and Hardness Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III456
9.1
9.2
9.3
10.0
10.1
10.2
10.3
Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III459
10.4
10.5
10.6
11.0
11.1
11.2
11.3
11.4
12.6
12.7
Retests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III468
12.8
13.0
13.1
13.2
13.3
13.4
13.5
Retests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III475
13.6
13.7
14.0
Fabrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III476
14.1
Forming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III476
14.2
14.3
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III476
14.4
Vacant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III477
14.5
14.6
Paragraph
14.7
Subject
Page
Tolerance for Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III477
14.8
15.0
15.1
15.2
15.3
15.4
Vacant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III478
15.5
15.6
15.7
15.8
15.9
15.10
15.11
15.12
Flux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III479
15.13
16.0
16.1
16.2
17.0
17.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III485
17.2
17.3
17.4
17.5
17.6
17.7
17.8
17.9
18.0
18.1
19.0
19.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-III488
19.2
19.3
APPENDIX W
WELDING OF TANK CAR
TANKS
1.1
INTRODUCTION
1.2 Scope
Appendix W describes AAR requirements for fusion welding on tank heads, shells, sumps, and
welds attaching connections thereto. Other welding on tank cars, shall be in accord with the
American Welding Society (AWS) Railroad Welding Specification D15.1, latest revision.
1.3
Certified
Facilities
Fusion welding on tank car tanks shall be performed only by facilities certified by the AAR for fabrication or for alterations, conversions, or welded repairs. See Appendix B.
1.4 Repairs, Alterations and Conversions
For repairs, alterations, and conversions to tank car tanks, see Appendix
R.
1.5
Welding
Symbols
Welding symbols used shall conform to AWS Standard A2.4 (see Fig.
W22).
2.0 DEFINITIONS
In addition to definitions and abbreviations in DOT 179.2, the following definitions apply in this
appendix. Where not defined herein, the definitions contained in AWS Standard A3.0 apply.
Table W1. General definitions (page 1 of 3)
Butt weld
Certified
Company
Double-welded butt
joint
Essential variables
Extension
Fabricate (fabrication)
10/2007
Fillet weld
Fluoroscope
10/2007
A weld of approximately triangular cross section joining two surfaces approximately at right angles to each other, in a lap, tee, or
corner joint.
A phosphor screen, X-ray image intensifier, or other fluorescent
medium that emits visible light in direct proportion to the
amount and distribution of radiation impinging on its input
surface.
C-III [M-1002] 7
Forge welding
Full fillet weld
Fusion Welding
Groove weld
Heat treatment
Lap joint
Nondestructive testing
Plug weld
Radiotape
Single-welded butt joint
Size (fillet)
Slot weld
Welder
Welding operator
Welding procedure
specification (WPS)
10/2007
3.3.1 For manual and semiautomatic welding procedures, the weld root pass and each layer of multipass weld shall be visually checked to make sure they are free from cracks, overlap, incom- plete
fusion, and inclusions prior to deposition of subsequent passes. The welder making the weld is
responsible for this, which shall be monitored by the welding inspector.
3.3.2 All completed welded butt joints shall be visually inspected in accord with paragraph 15.11 below
and radiographed in accord with paragraph 19.0, also below.
3.4 Welds Other than Tank Shell JointsAttachments Welded Directly to the Tank Shell
3.4.1 The root pass and each layer of multi-pass weld shall be visually checked to make sure they are free
from cracks, overlap, lack of fusion, and slag inclusions prior to deposition of subsequent weld
passes. The welder making the weld is responsible for this, which shall be monitored by the
welding inspector.
3.4.2
All completed welds shall be visually inspected in accord with paragraph 15.11 below.
3.4.3 In addition to the requirements in paragraphs 3.3.1 and 3.3.2, pressure car tank and alumi- num
tank (pressure and nonpressure) completed fillet welds listed below shall be examined in
accord with paragraph 11.0 below. For carbon steel tanks, the completed welds shall be examined
by magnetic particle or liquid penetrant, and for aluminum tanks by liquid penetrant. Where practical, the completed welds shall be examined after postweld heat treatment or no sooner than 24
hours after welding.
Tank anchor pad-to-tank, around the ends of the pad, including at least 3 in. of the longitudinal welds
Draft sill pad-to-tank, around the outboard end of the pad, including at least 3 in. of the
longitudinal welds
Draft sill pad-to-tank, around the inboard end of the pad, including at least 3 in. of the longitudinal welds, except where pads extend the full length of the tank
For aluminum tanks only, bolster pad to tank, around the upper end of the pad, including
at least 3 in. of the circumferential welds
3.4.4 Ultrasonic testing of welds may be employed in lieu of magnetic particle or liquid pene- trant
inspections. Ultrasonic testing of welds shall be performed in accord with the requirements of
paragraph 11.0 below.
4.1
4.2
4.2.1 When required by DOT specifications, test plates shall be prepared, tested, and evaluated in
accordance with applicable portions of paragraphs 5.0, 6.0, 7.0, and 9.0 below.
4.2.2
A test plate shall be prepared during fabrication for each WPS used in fabrication of the tank
shell.
4.2.3 When more than one welder and/or welding operator welds on a tank, the test plates shall be made
by the welder and/or welding operator designated by the fabricators inspector.
4.2.4 A test plate shall be prepared as a part of the qualification requirements for each welding
procedure. See paragraph 13.1.2 below.
4.2.5 When impact tests are required, the test plate groove details shall be the same as used for the tank
fabrication.
4.2
Longitudinal
Plates
Joint
Test
4.2.1 For each tank having a longitudinal welded joint, a test plate shall be prepared from mate- rial of
the same specification and thickness as the shell plates of the tank. Test plate material may be
taken from any part of one or more plates of the same lot of material that is used in the fabrication of the tank without reference to the direction of mill rolling, except when impact tests are
required. When impacts are required, test plates shall be oriented the same as the shell plates
with respect to mill rolling and weld directions.
4.2.2 The test plates may be attached to a shell plate being welded, reference Fig. W1A, so that the
weld metal shall be deposited in the test plate continuously with the weld metal deposited in the
longitudinal joint.
4.2.3 As an alternative, detached test plates may be prepared, but weld metal shall be deposited using
the same WPS used for the longitudinal joints.
4.3
Circumferential
Plates
Joint
Test
4.3.1 When a test plate is welded for the longitudinal joints of a tank, none need be prepared for the
circumferential joints in the same tank, provided the same WPS is used for both types of joints.
4.3.2 When the WPS for circumferential joints is different from the one used for longitudinal joints, a
detached test plate shall be prepared using the same WPS used for the circumferential joints.
4.4
Straightening
of
Test
Plates
The test plate shall be supported so that distortion resulting from welding shall not throw the finished test plate out of line by an angle over 5. Where the welding has distorted the test plate, it
shall be straightened before being stress-relieved or heat-treated. Where stress relieving or heat
treatment are not specified (aluminum and stainless steel, for example), test plates out of line by
an angle over 5 cannot be mechanically flattened. They must be scrapped and the test repeated.
4.5
4.5.1 The test plate shall be subjected to the same postweld heat treatment procedure required in
paragraph 17.0 below for the related tank. At no time shall the test plate be heated to a
tempera- ture higher than that used for postweld heat treating the related tank.
4.5.2 When production test plate impact test specimens are required by DOT or AAR special commodity requirements, the test plate shall be postweld heat treated with its related tank.
10/2007
C-III [M-1002] 11
10/2007
4.7
4.7.1 For tanks built of materials listed in Tables M10.1, M10.2, M10.3, M10.4, M10.5, M10.6, and
M10.7, the production-welded test plate dimensions shall be sufficient to provide one reducedsection tension specimen conforming to Fig. W2A, plus two guided-bend specimens, either two
side-bends, or one face-bend and one root-bend, or one longitudinal face-bend and one longitudinal
root-bend.
4.7.2 For tanks built of materials listed in Tables M10.1, M10.5, and M10.7, include sufficient mate- rial
to provide three impact specimens each of weld metal and heat-affected zone, when required.
5.1
TYPES
TESTS
AND
PURPOSES
OF
5.2
Tension
tests
Direct-tension tests are used in welding procedure qualification and production-weld tests.
Joint-tension specimens are used to measure strength of butt-welded joints.
All-weld-metal-tension specimens are used to measure strength and ductility of weld metal.
5.2.2
Bend
tests
Bend tests are used in welding procedure and welder performance qualification and production-weld tests.
Guided-bend tests are used to measure soundness and ductility of butt-welded joints.
5.2.3
Fillet
tests
weld
Fillet weld tests are sometimes used in welding procedure and welder performance tests to
check the size, contour, and penetration of fillet welds and degree of soundness of filletwelded joints.
5.2
Impact
Tests
5.2.1 Impact tests are used to evaluate welding procedures and production welding when the tank
service involves the transportation of a low-temperature product.
5.2.2 Charpy impact tests are used to measure notch toughness, at low temperatures, of weld metal
and weld heat-affected zone of butt welded joints.
5.3
Radiographic
Tests
5.3.1 Radiographic examination of a length of weld is used to evaluate the ability of a welding operator
to make an acceptable butt-welded joint. Under certain conditions, radiographic exami- nation
may be used as an alternative to mechanical tests for welder performance qualification.
5.3.2 Radiographic examination is recommended for welding procedure and production-welded test
plates to measure acceptance for preparation of test specimens.
5.4
Corrosion
Tests
Corrosion tests are used to determine that weld, heat-affected zone, and plate specimens, from test
plates made from materials listed in Table M10.3, are not susceptible to intergranular attack associated with precipitated chromium carbides and meet the acceptable corrosion rates listed in
Appendix M, paragraph 3.3.2.
5.5
Hardness
Tests
Hardness tests are used to evaluate production welding and to control maximum hardness
requirements.
6.1
6.2.1 The all-weld-metal tension specimen required for welding procedure qualification shall be taken
entirely from weld metal (at least the reduced section) and shall conform to the dimensional
requirements of Fig. W3.
6.2.2
6.3
This specimen is not required if the test plate thickness is less than 5/8 in. (15.9
mm).
Joint-Tension Tests
6.3.1 Tension test specimens shall be ruptured under tensile load. The tensile strength shall be computed
by dividing the maximum load at failure by the least cross-sectional area of the speci- men, as
measured before load is applied.
6.3.2
6.3.3 If the joint specimen breaks in the base material outside the weld, the test shall be accepted as meeting
the requirements, provided the strength is not more than 5% below the specified ten- sile strength of
the base material as specified in Table M10.
6.4
6.4.1 For the all-weld-metal specimen (the all-weld-metal turned reduced-section test specimen is acceptable),
fit the ends of the fractured specimen together carefully and measure the distance between the
gauge marks to the nearest 0.01 in. (0.254 mm). The elongation is the increase in length of the
gauge length, expressed as a percentage of the original gauge length.
6.4.1.1 The elongation shall be not less than the value specified for base material in Table M10.
6.4.1.2 If any part of the fracture takes place outside of the middle half of the gauge length or in a punched
gauge mark, the elongation value obtained may not be representative of the material. If the
elongation so measured meets the minimum requirements, no further testing is required; but if the
elongation is less than the minimum requirements, discard the test and make a retest.
6.4.2
C-III [M-1002] 15
7.1
BEND
TESTS
SPECIMENS
AND
7.2
7.2.1 Guided-bend test specimens conforming to requirements of Fig. W4B and Fig. W5 shall be used
for qualification tests of welding procedures and welder performance and for productionwelded impact test plates.
7.2.2 Rectangular specimens cut from the test plates are of five types: side-bend, face-bend, root- bend,
longitudinal face-bend, and longitudinal root-bend. The cut surfaces shall be designated the
sides of the specimens. The other two surfaces shall be called face and root, the face
having the greater width of weld metal.
7.2
Guided-Bend
Tests
7.2.1 Guided-bend specimens shall be bent in test jigs that are substantially in accord with Fig. W6.
The surface of the specimen on the convex (outer) surface of the bent specimen shall be the
face for face-bend and longitudinal face-bend specimens; the root for root-bend and
longitudinal root-bend specimens; and the side (with greater defects, if any) for side-bend
specimens. The specimen at the time of bending shall be between the temperature of 50 F (10
C) and 140 F (60 C). Apply the bending force smoothly without shock, and bend the specimen
into the die at a duration no faster than 15 seconds but no slower than 120 seconds by
applying a load on the plunger until a 1/8-in. (3.18-mm) diameter wire cannot be inserted
between the specimen and any point on the plunger.
7.2.2 Specimens shall pass the test if they have no cracks or other open defects exceeding 1/8 in.
(3.18 mm), measured in any direction on the convex surface of the specimen after bending, except
that cracks occurring on the corners of the specimen during testing shall not be considered, unless
there is definite evidence that they result from inclusions or other internal defects.
8.1
FILLET
TESTS
WELD
SPECIMENS
AND
8.2
Fillet
Weld
(Tee-Joint)
Specimens
T-joint specimens, when required, shall conform to requirements of Fig.
W7.
8.1.1 The fillet weld specimen may be used for qualification test of welder performance and shall be cut
to provide a T-joint section for lateral loading and to provide a cross-section of the weldment, to be
smoothed and etched with a suitable etchant, to give a clear definition of the structure of the weld
metal and heat-affected zone. See Fig. W7A.
8.1.2 The fillet weld specimen shall be used for qualification test of welding procedures for ferritic steels
with their mechanical properties enhanced by quenching and tempering. It shall be cut to
provide five cross-sections of the weldment, each approximately 2 in. (50.8 mm) long. One face of
each section is to be smoothed and etched with suitable etchant to give a clear definition of structure of the weld metal and heat-affected zone. See Fig. W7B.
8.2
Fillet
Tests
Weld
8.2.1 The T-joint specimens prepared in accord with Fig. W7A shall contain no visible cracks.
8.2.2 The vertical member of the performance qualification T-joint shall be loaded laterally and the load
steadily increased until the specimen fractures or bends flat upon itself. To pass, the spec- imen
shall not fracture; or, if it fractures, the fractured surfaces shall show no evidence of cracks or
incomplete root fusion, and the sum of the lengths of open discontinuities visible on the fractured
surfaces shall not exceed 2 in. (50.8 mm) for ferrous materials and 3/4 in. (19.0 mm) for
nonferrous materials.
8.2.3 The performance qualification T-joint weld shall have no concavity or convexity greater than
1/16 in. (1.59 mm) and shall have not more than 1/16 in. (1.59 mm) difference in the lengths of
the legs of the fillet weld.
8.2.4 The procedure qualification T-joint weld shall have not more than 1/8 in. (3.18 mm) differ- ence in
the lengths of the legs of the fillet weld.
8.2.5 Visual examination of the etched cross sections of weld metal and heat-affected zones of
performance and procedure qualification T-joint welds shall show freedom from cracks and complete fusion at the joint root, but not necessarily beyond the root.
9.1
Test
Results
Retests
and
9.1.4.1 Unless otherwise specified in the tank specification, the minimum impact test values of full-size
and subsize specimens shall be as shown in Table W2.
Table W2. Minimum impact test values
Minimum Value
Minimum Value
10/2007
9.1.4.2 If the value for more than one specimen is below the minimum value specified for the average
of three specimens, or if the value for one specimen is below the minimum value specified for one
of the three specimens (the other two being not less than the minimum value specified for the
average of three specimens), a retest of three additional specimens shall be made, each of
which must be equal or exceed the specified minimum value for the average of three specimens.
Such a retest shall be permitted only when the average value of the three specimens equals or
exceeds the minimum value specified for one of the three specimens.
9.1.4.3 If the required values are not obtained upon retest, or if the values on the initial test are below the
minimum required for retest, the welding procedure and/or the weld metal as the case may be
shall be rejected.
9.1.4.4 When an erratic result is caused by a defective specimen, or there is uncertainty in test
procedure, a retest shall be allowed.
9.1.5
Reports
9.1.5.1 A report of impact test results shall include identity of plate material (specification, grade,
and heat number), PQR, and welding electrodes; type and size of impact test specimens;
location and orientation of specimens and notches with respect to plate surface and rolling direction; and weld metal and weld heat-affected zone impact value for each specimen tested.
9.1.5.2 The complete report of all impact tests shall be retained for not less than five years by the tank
fabricator, or by the car owner if the owner so requests.
9.2 Corrosion Specimens and Tests
Corrosion tests are required on tanks fabricated from materials listed in Table M10.3 when
required by the tank specification.
9.2.1 Material and number required
Test plates used to prepare specimens shall be provided from each heat of material used to fabricate tanks and each heat of filler metal that is used to weld tanks. Where welding is involved, the
plates shall be welded using the same WPS as used on the tank. At least one set of three specimens shall be taken from the test plate, located as shown in Fig. W1B. Corrosion testing of the
base metal is not a requirement if the corrosion test has been conducted and certified by the material supplier. Specimens shall be tested in accord with ASTM A262-85 Practice A. If the results of
Practice A are unacceptable, further testing with Practice B or C is required.
9.2.2
Test
criteria
9.2.2.1 Corrosion test specimens shall be considered to be acceptable when each exhibits corro- sion rates
not in excess of those listed in Appendix M, paragraph 3.3.2.
9.2.2.2
9.2.3
9.2.3.1 A report of corrosion test specimens shall include identity of plate material (specification, grade,
and heat number), welding procedure, welding electrodes, and corrosion rate for each speci- men
tested.
9.2.3.2 The complete report of all corrosion tests shall be retained for not less than five years by the tank
fabricator, or by the car owner if the owner so requests.
9.3
Hardness
Tests
Hardness tests of production butt welds are required for pressure tank car tanks fabricated from
materials listed in Table M10.1.
9.3.1 On each tank, at least three points inside and three points outside shall be checked at the
centerline of the welds. Two of the inside points and two of the outside points shall be at intersections of longitudinal and circumferential butt welds. Grind the weld metal to produce a flat surface
for hardness testing at these check points. Do not grind weld reinforcement below joining plate
surface.
9.3.2 Hardness of weld shall not exceed Brinell 225 (Rockwell C20) after postweld heat treat- ment.
9.3.3 Hardness tests of butt welds on multi-unit tank car tanks shall be performed on exterior weld
seams only. One test per weld procedure is required on each tank.
10.1
10.2 Scope
The rules of paragraphs 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0, and 13.0 in this appendix apply
to qualification of welding procedures, welders, and welding operators for all types of manual and
machine welding processes permitted by the AAR Tank Car Committee.
10.3
Responsibility
10.3.1 Each facility shall be responsible for its welding and shall have on hand documentation required
by paragraph 10.3.
10.3.2 Each facility shall ensure that welders are trained and qualified in the areas of welding symbols,
welding procedures, acceptance criteria, and other sections of this specification applicable to their
work. The training shall be documented.
10.3.3 Welders not in the employ of the certified facility may be used to fabricate, alter, repair or convert
tank car tanks in accordance with this specification, provided all the following conditions are met.
10.3.3.1 The certified facility shall be responsible for all welding. Use of subcontract welders by an
extension is not permitted.
10.3.3.2 All welding shall be performed in accordance with the certified facilitys welding proce- dure
specifications.
10.3.3.3 All welders shall be qualified by the certified facility in accordance with this specifica- tion.
10.3.3.4
The certified facilitys quality control program shall include as a minimum the
following:
The designated authority for the administration of the welding quality control program.
A description of the administration and technical supervision for all welders.
A description of the exclusive authority to assign and remove welders without
involvement of any other organization.
A requirement for assigning welder identification symbols.
10/2007
10.3 Records
Each facility shall maintain a WPS of each of its qualified welding procedures and shall maintain
records (PQR) obtained in qualification of welding procedures and performance qualification of
welders and welding operators. These records shall be certified by a responsible official of the
com- pany and shall be accessible to the AAR representative. Companies may centralize record
storage. Recommended forms for these records are shown in Figs. W12, W13, and W14.
10.4
Identification
of
Welds
Each qualified welder and welding operator shall be assigned a unique identifying number, letter,
or symbol by the facility. The assigned identification shall be used to identify the work of that
welder or welding operator.
10.5
Qualification
Restrictions
10.5.1 Facilities shall use AAR-qualified welders and welding operators. ASME performance
qualification for plate materials listed in Appendix M, paragraph 3.0, may be accepted as meeting
this requirement. Radiography used for ASME performance qualification must be in accord with
Appendix W. Completed test plate assemblies must be visually inspected in accord with
paragraph 15.11 below and with paragraph 15.6 or paragraph 15.7, also below, as applicable.
10.5.2 Welders and welding operators shall be tested under the full supervision and control of the
company. Each facility shall qualify the welding procedures, welders, and welding operators used
to produce welds meeting this appendix. The test results from one facility or company shall not be
used to qualify a welding procedure, welder, or welding operator for another company, except that
companies with multiple facilities may share welding procedure specifications when the essential
variables are the same. It is permissible, however, to subcontract preparation of test materials for
welding, preparation of test specimens from completed weldments, nondestructive examination,
and mechanical testing, provided the company accepts full responsibility for any such work.
10.5.3
10.6
Weld
Orientation
Positions
and
Test
10.6.1 The orientation of butt and fillet welds with respect to horizontal and vertical planes of
reference are classified as shown in paragraphs 10.6.2 through 10.6.6 below and in Fig. W8.
10.6.2
10.6.4 Performance qualification in one of the above positions shall permit welding within the range of
orientation specified for that position in the table in the tables in Figs. W8 and W9.
10.6.5 Welders who pass the required groove or fillet weld tests listed in paragraphs 10.6.2 or
10.6.3 shall be qualified for the positions of groove welds and fillet welds shown in Table W3.
Weld- ing vertical down requires separate qualification.
Table W3. Performance qualificationposition limitations
Qualification Test
a/
Weld
PlateGroove
Position
1G
2G
3G
4G
3G and 4G
2G, 3G, and 4G
PlateFillet
1F
2F
3F
4F
3F and 4F
F
F, H
F,H,V
F,H,O
All
10.6.6 A facility that does fabrication, repair, alteration, or conversion in a particular position
may make the tests in that position, but such a performance qualification is valid only for the flat
position and for the position actually tested, except that an angular deviation of 15 is permitted
in the inclination of the weld axis and the rotation of the weld face as defined in Figs. W8 and W9.
10/2007
11.1
11.2 Scope
These paragraphs define the acceptance criteria and personnel qualifications that shall be used
whenever nondestructive test methods are required by this specification or in a tank specification.
Acceptance criteria for nondestructive testing are described in the following paragraphs:
Radioscopy, paragraph 11.2
Liquid penetrant, paragraph 11.3
Magnetic particle, paragraph 11.4
Ultrasonic examination, paragraph 11.5
11.3
11.2.1
General
11.2.1.1 A detailed procedure for the radiographic examination of welded joints shall be estab- lished in
accord with Appendix T by each facility.
11.2.1.2 A Level II NDT technician, qualified in accord with Appendix T, shall review and approve all
required radiographic examinations.
11.2.2
11.2.2.1 Reference radiographs of ASTM E390, Reference Radiographs for Steel Fusion Welds, are
accepted as a guide to types and degrees of discontinuities detectable by radiographs of steel
welds.
11.2.2.2 Welds whose radiotapes show any of the following types of imperfections shall be unac- ceptable:
An elongated slag inclusion that has a length greater than 1/4 in. (6.35 mm) for T up to
3/4 in. (19.0 mm), or 1/3 T for T from 3/4 in. to 2 1/4 in. (19.0 mm to 57.2 mm) (T is
thick- ness of the thinner plate of the joint)
A group of slag inclusions in line that have an aggregate length greater than T in a weld
length of 12T, except when the distance between successive inclusions exceeds 6L, where
L is the length of the longest inclusion in the group
Any type of crack or zone of incomplete fusion or incomplete penetration
Porosity in excess of that specified as acceptable in paragraphs 11.2.3 and 11.2.4 below
Other round inclusions shall be judged on the same basis as porosity
11.2.3
Porosity
11.2.3.1 Images of a general circular or oval shape shall be interpreted as porosity for the pur- pose of
this standard. For radiography, the image will appear dark. For fluoroscopy, the image will appear
light.
11.2.3.2 Permissible porosity indications for weld thicknesses intermediate to those illustrated shall be
evaluated by comparison with porosity chart for the next thinner material or by calcula- tion as
shown in Table W4.
11.2.3.3 The total area of the porosity as determined from the radiograph shall not exceed 0.060T in.2
(38.7T mm2) in any 6-in. (152-mm) length of weld, where T is the thickness of the weld. If the
weld is less than 6 in. (152 mm) long, the total area of porosity will be reduced in proportion.
11.2.3.4 In any 1-in. (25.4-mm) length of weld or 2T, whichever is smaller, porosity may be clus- tered to a
concentration four times that permitted by 0.060T in.2 (38.7T mm2). Such clustered porosity
shall be included in the porosity in any 6-in. (152-mm) length of weld that includes the cluster.
11.2.3.5 Aligned porosity shall be acceptable provided the summation of the diameters of the pores is no
more than T in a length 12T or 6 in. (152 mm), whichever is less, provided each pore is separated
by a distance at least six times the diameter of the largest adjacent pore. Aligned poros- ity
indications shall be counted in the total area of permissible indications in any 6-in. (152-mm)
length of weld.
11.2.3.6 The maximum pore dimension shall be 0.2T or 1/8 in. (3.18 mm), whichever is smaller, except that
an isolated pore separated from an adjacent pore by 1 in. (25.4 mm) or more may be 0.3T or 1/4
in. (6.35 mm), whichever is less.
Table W4. Maximum permissible porosity indications in radiotapes per 6-in. length of weldconventional units
Weld
Thickness, in.
1/4
1/2
3/4
1
1 1/2
2
a/
Total Area
ofPermitted
Porosity,
in.2
0.015
0.030
0.045
0.060
0.090
0.120
3/32
1/8
1/8
1/8
1/8
Decimal
Value,
in. a/
0.10
0.125
0.125
0.125
0.125
No.
4
4
5
7
10
Approx.
Fraction,
in.
3/128
1/32
1/32
5/128
3/64
7/128
Decimal
Value,
in. a/
0.025
0.031
0.034
0.039
0.048
0.055
No.
31
40
50
50
50
51
Approx.
Fraction,
in.
1/64
3/128
3/128
1/32
1/32
5/128
Decimal
Value,
in. a/
0.0138
0.0195
0.024
0.0275
0.034
0.039
No.
100
101
99
101
99
100
Table W5. Maximum permissible porosity indications in radiographs per 15.2-mm length of weldSI units
Weld
Thickness, mm
6.35
12.7
19.0
25.4
38.1
50.8
a/
Total Area
of Permitted
Porosity,
mm2
9.68
19.4
29.0
38.7
58.1
77.4
Decimal Value,
mma/
No.
Decimal Value,
mma/
No.
Decimal Value,
mma/
No.
2.54
3.18
3.18
3.18
3.18
4
4
5
7
10
0.64
0.79
0.86
0.99
1.22
1.40
31
40
50
50
50
51
0.351
0.495
0.610
0.699
0.864
0.991
100
101
99
101
99
101
11.2.4
Porosity Charts
11.2.4.1 The porosity charts, Figs. W17 through W20, illustrate various types of assorted and uniform,
randomly dispersed porosity indications. The chart for each thickness represents the
maximum acceptable porosity. The charts represent full-scale 6-in. radiographs and shall not be
enlarged or reduced. The porosity distributions shown are not necessarily the patterns that may
appear on the radiograph, but are typical of the number and size of indications permitted. When
porosity indications differ significantly from the porosity charts, the actual numbers and sizes of
the pores may be measured and the total area of porosity calculated.
11.2.4.2 Porosity charts are identical with the 1974 edition of Section VIII, Division 1 of the ASME
Boiler and Pressure Vessel Code, Appendix 4, published by the American Society of
Mechanical Engineers, 345 East 47th Street, New York, New York, 10017, and are reproduced by
permission.
10/2007
C-III [M-1002] 25
11.3
11.3.1
General
11.3.1.1 This section describes methods that shall be employed whenever liquid penetrant exam- ination is
specified in this specification or in a tank specification. A Level II NDT technician, qual- ified in
accord with Appendix T, shall review and approve all required liquid penetrant examinations.
11.3.1.2 Liquid penetrant examination shall be performed in accord with a written procedure qualified
by the facility to be in accord with the requirements of Appendix T.
11.3.2 Evaluation of Indications
An indication is the evidence of a mechanical imperfection. Only indications with major dimensions greater than 1/16 in. shall be considered relevant.
11.3.2.1 A linear indication is one having a length greater than three times the width.
11.3.2.2 A rounded indication is one of circular or elliptical shape with the length equal to or less than three
times the width.
11.3.2.3 Any questionable or doubtful indications shall be reexamined to determine whether or not they
are relevant.
11.3.3
Acceptance Standards
11.3.3.1 These acceptance standards shall apply, unless other more restrictive standards are specified for
specific materials or applications within this specification. Any indication that is believed to
be nonrelevant shall be regarded as an imperfection, unless it is shown by reexamina- tion, by the
same method or by the use of other nondestructive methods and/or by surface condition- ing, that
no unacceptable imperfection is present.
11.3.3.2
11.4.1.1 A Level II NDT technician, qualified in accord with Appendix T, shall review and approve all
required magnetic particle examinations.
11.4.1.2 Magnetic particle examination shall be performed in accord with a written procedure qualified
by the facility to be in accord with the requirements of Appendix T.
Acceptance Standards
11.4.3.1 These acceptance standards shall apply, unless other more restrictive standards are specified for
specific materials or applications within this specification. Any indication that is believed to
be nonrelevant shall be regarded as an imperfection, unless it is shown by reexamina- tion, by the
same method or by the use of other nondestructive methods and/or by surface condi- tioning, that
no unacceptable imperfection is present.
11.4.3.2
Ultrasonic Examination
11.5.1
General
11.5.1.1 Ultrasonic examination may be employed in accord with Appendix T for groove welds in butt joints
on tank car tanks. A detailed procedure shall be established in accord with Appendix T by each
facility.
11.5.1.2 A Level II or Level III NDT technician, qualified in accord with Appendix T for ultra- sonic
testing, shall review and approve all required ultrasonic examinations.
11.5.2 Ultrasonic Acceptance Criteria
Discontinuities that produce a response greater than 20% of the reference level shall be investigated to the extent that the operator can determine the shape, identity, and location of all such discontinuities and evaluate them in terms of the acceptance standards given below:
11.5.2.1 Indications characterized as cracks, lack of fusion, or incomplete penetration are unac- ceptable
regardless of length.
11.5.2.2 Any relevant indication that intersects the surface of the component or weld shall be rejectable,
unless the indication is determined to be caused by a visually (VT) acceptable condition.
11.5.2.3 Other discontinuities are unacceptable if the indications exceed the reference level and have
lengths that exceed the following:
10/2007
C-III [M-1002] 27
11.5.2.3.2 A group of indications that have an aggregate length greater than Ta/ in a weld length of 12T or 6
in., whichever is less, except when the distance between successive indications exceeds 6L, where
L is the length of the longest indication in the group.
11.5.3 Any indication that is believed to be non-relevant shall be regarded as an imperfection
unless it is shown by reexamination that no unacceptable imperfections are present. Reexamination shall be performed by the same method or by the use of other nondestructive methods and/or
by surface conditioning.
12.1
12.2
Qualification
of
Welders
Each welder shall pass the mechanical tests prescribed in paragraph 12.6 below for performance
qualification, except that welders making a groove weld with shielded metal-arc welding, fluxcored arc welding, gas metal arc welding (except short circuiting), or gas-shielded tungsten arc
welding may alternatively be qualified by radiographic or ultrasonic examination as prescribed in
paragraph 12.6 below. The welder who welds the welding procedure qualification test plate that
results in a qualified WPS shall be performance qualified, but only within the limits of essential
variables given in paragraph 12.4 below.
12.2.1 Performance qualification tests for butt, fillet, and buildup welds, including nozzles and other
circular attachments to the shell, shall be made using butt-welded test plates (see Figs. W4A,
W15, W21C, and W21D). Satisfactory qualification test results on specimens prepared from the
butt-welded test plates, or alternatively by radiographic examinations, shall qualify a welder to
make butt welds in thicknesses determined by test plate thickness and fillet welds in all thicknesses, both within the range of essential variables as recorded in the welders Record of Welder
Performance Qualification Test (see Fig. W14).
12.2.2 Performance qualification tests for fillet welds, only, may be made using fillet-welded test plates
(see Figs. W7A and W16. Satisfactory qualification test results on specimens prepared from the
fillet-welded test plate shall qualify a welder to make fillet welds in all thicknesses within the
range of essential variables as recorded in the welders Record of Welder Performance Qualification Test (see Fig. W14).
12.2
Qualification
of
Welding
Operators
Each welding operator who welds on tanks being fabricated, repaired, altered, or converted shall
be performance-qualified for each welding process under which the welder does welding with
auto- matic welding equipment, in which both the rate of travel and position of welding head
with respect to the work are controlled mechanically, except for minor adjustments for such
factors as plate unevenness, out-of-roundness, and lead angle of the welding head. The welding
operator who welds the welding procedure qualification test plate that results in a qualified WPS
shall be per- formance-qualified.
12.2.1 A 3-ft (914-mm) length of weld made by the operator shall be radiographed using the tech- nique of
paragraph 11.0 above. To qualify the operators performance, the radiograph shall comply with the
acceptance standards of the same section. The length of weld radiographed may be that of a test
plate or of production welding.
12.2.2 If the weld does not comply with the acceptance standards, second and subsequent 3-ft (914mm) lengths welded by the operator using the machine-welding procedure shall be radiographed, until the operator demonstrates that he or she is capable of producing welds that comply
with the acceptance standards. Production welds so examined shall be unacceptable if they do not
comply with the minimum requirements for the tank being fabricated.
a/
"T" is the thickness of the weld excluding any allowable reinforcement. For a butt weld joining two mem-
bers having different thicknesses at the weld, "T" is the thinner of these two thicknesses. If a full penetration
weld includes a fillet weld, the thickness of the throat of the fillet shall be included in "T."
12.2.3 The results of the radiographic examination shall be recorded and retained by the facility. The
radiographs may be retained or be discarded.
12.2.4 Performance qualification tests for fillet welds only may be made using fillet-welded test plates
(see Figs. W7.1 and W16. Satisfactory qualification test results on specimens prepared from the
fillet-welded test plate shall qualify a welder to make fillet welds in all thicknesses within the
range of essential variables as recorded in the welders Record of Welder Performance Qualification Test (see Fig. W14).
12.3
12.3.1 Welds requiring a combination of processes may be performed by one or more welding
operators or welders, each welding only that portion of the weldment for which he or she is performance-qualified.
12.3.2 Where a combination of processes are used, the welder or welding operator who is to make the root
pass shall be tested only by means of a minimum of two root-bend specimens instead of the facebend and side-bend specimens required in Table W7.
12.4
Essential
Variables
When any of the applicable changes in the essential variables as described in paragraph 16.2
below and in Table W6 are made, the welder must be requalified.
Table W6. Essential variablesperformance qualification
Jointsparagraph 16.2.1
Base Metalsparagraph 16.2.2
Filler Metalsparagraph 16.2.3
Positionsparagraph 16.2.4
Electrical Characteristics
paragraph 16.2.7
Shielding Gas or Fluxparagraph 16.2.8
16.2.8.2
Techniqueparagraph 16.2.9
16.2.9.5, 16.2.9.6 16.2.9.5, 16.2.9.6
12.5
16.2.8.2
16.2.9.5, 16.2.9.6
16.2.9.6
Test
Joints
12.5.1 Information regarding the essential variables in paragraph 12.4 above (base material, filler
metal, welding position, etc.) shall be recorded in the facilitys Record of Welder Performance
Qualification Test prepared for each welder qualified (see Fig. W14.) Other details that are essential variables of the WPS being used shall be followed in making the performance qualification,
except as otherwise allowed below. Postweld heat treatment of welder performance test coupons
may be omitted. The dimensions of the test plates and the length of the weld shall be sufficient to
provide the required test specimens. If the alternative qualification by radiographic or ultrasonic
examination is used for groove welds as permitted in paragraph 12.1, the minimum length of weld
radiographed or ultrasonically inspected and evaluated in plate shall be 6 in. (153 mm) and shall
include a stop-start in each pass along the length of weld.
12.5.2 The dimensions of the welding groove for the test joint for double-welded butt joints and for
single-welded butt joints with or without backing strip shall be the same as those for any WPS the
facility has qualified. The dimensions of the fillet weld shall be as shown in Fig. W7A.
10/2007
12.5.3 Carbon and alloy steel. When a welder is to be qualified to weld on carbon or alloy steel, except
austenitic stainless steels of P-8, the test plates shall be base metal of the P-number or Pnumbers to be joined in production welding, except that carbon steel P-1 base metals may be used
for the qualification tests, with the following limitations:
12.5.3.1 The total alloy content of the base metal, for which carbon steel base metal is substi- tuted, shall
not exceed a nominal 6%. The total alloy content of the weld metal used shall not exceed this
nominal 6%.
12.5.3.2 When a welder is to be qualified to weld on alloy steel base metal that has a total alloy content
exceeding a nominal 6%, carbon steel plates may be used in the performance qualification tests
when using F-41 filler metal of Table W12. No preheating or postheating is required.
12.5.3.3 When alloy steel filler metals as permitted in paragraph 12.5.3.1 above are used on car- bon
steel plate, the test specimens are to be preheated and postheated in accord with the WPS.
12.5.4 Austenitic stainless steel and nickel-base alloys. When a welder is to be qualified to weld on
austenitic stainless steel P-8 metal or nickel alloy P-41 metal, carbon steel plates of P-1 may be
used for the performance test.
12.5.5 When a welder is to be qualified for the use of F-5 filler metal of weld metal analysis A-7 or A-8 to
join P-1 or P-8 base metals to themselves or to each other, carbon steel plate may be used for the
performance qualification test. A performance qualification test made using A-8 or A-9 (F-5
filler metals) with one or a combination of P-1 or P-8 base metal will qualify for all combinations
of these base metals.
12.6
Test
Specimens
12.6.1 The qualification test weld shall be visually inspected in the as-welded condition (no grinding
after completing the weld) in accordance with paragraphs 15.6 and 15.11 below, except that
reinforcement may be up to 1/8 in. For welder performance qualification by mechanical test- ing,
the type and number of test specimens required, together with the range of thickness of mate- rials
for which a welder is qualified by use of a given thickness of test plate, are shown in Table W7.
When alternative qualification by radiographic or ultrasonic examination of groove welds is used
as permitted in paragraph 12.1, the range of thickness of materials for which a welder is
qualified shall be the same as for mechanical testing in Table W7.
12.6.2 Test specimens may be removed from the welded test plates in any order, but in a manner similar
to that shown in Figs. W21C and W21D.
12.6.3 All test specimens shall be prepared, tested and meet the requirements as prescribed in
applicable portions of paragraphs 7.0, 8.0, and 10.0 of this appendix. When alternative qualification by radiographic or ultrasonic examination of groove welds is used as permitted in
paragraph 12.1, the radiographic or ultrasonic acceptance standards of the applicable portions of
paragraph 11.0 above shall be used.
12.6.4 The number of test plates (and sets of test specimens) required by Table W7 shall be pre- pared
and tested to provide performance qualification of each welder for the test positions that will
be used in the fabrication, repair, alteration, or conversion of tank car tanks.
Table W7. Performance qualification tests required
Range of Thickness of
Material Qualified by
Test Plate, in. (mm)
Type
of
Joint
Butt
Butt
Min.
1/16e/
(1.59e/)
3/16 (4.76)
or
Over 3/8 (9.5) but less than 1/2
3/16 (4.76)
Max.
2t
2t
2t
Max. to be
3/16 (4.76) weldedf/ g/
All thicknesses
1
1
1
1
2
2
1
a/
12.7 Retests
A welder who fails the performance qualification tests may be retested under the following conditions:
12.7.1 If one or more of the test specimens prescribed in Table W7 fails to meet the requirements, or if the
qualification failed has been that of the alternative qualification by radiographic examina- tion of
paragraph 12.6 above.
12.7.1.1 When a retest is made without further training or practice, the welder shall make two test welds
of each type for each test position on which the welder failed, all of which shall meet the
requirements.
12.7.1.2 When the welder has had further training or practice, a complete retest shall be made for each
test position on which the welder failed to meet the requirements.
12.7.2 If the performance qualification test failed was by radiographic or ultrasonic examination,
the retest shall be by the radiographic or ultrasonic examination method, respectively.
10/2007
PROCEDURE QUALIFICATION
13.2
Qualification of Procedures
13.2.1 All welding shall be done in accord with a WPS. Each manufacturer or contractor shall qualify
each WPS used by the welding of test coupons and the testing of specimens as required by this
appendix, recording the welding conditions and test results in a PQR. The essential variables
of the WPS must be within the limits that are qualified by the PQR.
Each facility must have and document a clearly defined system to ensure that the welding parameters being used are within the limits of a qualified WPS. For gas shielded processes, the gas flow
rate range will be specified on the WPS.
13.2.2 Except for steels having their mechanical properties enhanced by quenching and temper- ing,
procedure qualification tests for butt and fillet welds shall be made using butt-welded test
plates (see Figs. W4A, W15, W21A, and W21B). Procedures used for deposits of metal applied to
the surface (except those covered by paragraph 13.7 below) shall be qualified by using butt-welded
test plates. Satisfactory qualification test results on specimens prepared from the butt-welded test
plates shall qualify a welding procedure for use with both butt and fillet welds, including nozzles
and other circular attachments to the shell, within the range of essential variables of its WPS. (See
Fig. W12.)
13.2.3 For steels having their mechanical properties enhanced by quenching and tempering, pro- cedure
qualification tests for butt welds shall be made using butt-welded test plates (see Figures Figs.
W4A, W15, W21A, and W21B), and tests for fillet welds shall be made using fillet-welded test
plates (see Figs. W7B and W16). Satisfactory qualification test results on specimens prepared from
the butt-welded test plates shall qualify a welding procedure for use with butt welds, including
nozzles and other circular attachments to the shell, within the range of essential variables of its
WPS. Satisfactory qualification test results on specimens prepared from the fillet-welded test
plate shall qualify a welding procedure for use with fillet welds, including nozzles and other circular attachments to the shell, within the range of essential variables of its WPS. (See Fig. W12.)
13.2.4 Unless otherwise specified for special commodities (see 49 CFR 179.102), WPS used in welding
pressure car head and shell joints (including nozzle-to-shell welds) shall be qualified with PQRs
that have been Charpy impact tested at or below 30 F (34 C) to meet the requirements of
Table W2. Table W9, Supplementary Essential Variables, applies to procedure development.
Production tests do not require impact testing, unless otherwise specified. Austenitic stainless
steel tanks made in accord with paragraph 17.9.2 below without postweld heat treatment, using
type 304L or 316L filler metals meeting AWS specifications, are exempt from the requirements of
this paragraph. Weld procedures for special commodities shall match the base metal requirements
listed in 49 CFR 179.102.
13.2
Essential
Variables
When any of the applicable changes in the essential variables, as described in paragraph 16.2
below and in Tables W8 and W9, are made in a WPS, a new procedure qualification test will be
performed and documented on a PQR. Changes other than or within limits of those listed may be
made in the WPS and not require requalification, provided the WPS is revised to show the
changes. When notch toughness is required by the tank car specification, the supplementary
essential variables apply.
Table W8. Essential variableswelding procedures
Jointsparagraph 16.2.1
Base Metalsparagraph 16.2.2
SMAW
16.2.1.1, 16.2.1.2
16.2.2.1, 16.2.2.4,
16.2.2.7
Welding Process
GTAW
GMAW, FCAW
16.2.1.1, 16.2.1.2
16.2.1.1, 16.2.1.2
16.2.2.1, 16.2.2.4, 16.2.2.1, 16.2.2.4,
16.2.2.7
16.2.2.7, 16.2.2.8
SAW
16.2.1.1, 16.2.1.2
16.2.2.1, 16.2.2.4,
16.2.2.7
16.2.3.1, 16.2.3.2,
16.2.3.18,
16.2.3.19
16.2.3.1, 16.2.3.2,
16.2.3.3, 16.2.3.4,
16.2.3.12,
16.2.3.18,
16.2.3.19
16.2.3.1, 16.2.3.2,
16.2.3.3, 16.2.3.5,
16.2.3.6, 16.2.3.7,
16.2.3.8, 16.2.3.9,
16.2.3.12,
16.2.3.18, 16.2.3.19
Positionsparagraph 16.2.4
Preheatparagraph 16.2.5
Postweld heat treatment
paragraph 16.2.6
Electrical Characteristics
paragraph 16.2.7
Shielding Gas or Flux
paragraph 16.2.8
Techniqueparagraph 16.2.9
16.2.4.3
16.2.5.1, 16.2.5.3
16.2.6
16.2.4.3
16.2.5.1, 16.2.5.3
16.2.6
16.2.4.3
16.2.5.1, 16.2.5.3
16.2.6
16.2.7.2
16.2.7.1, 16.2.7.2
16.2.8.1, 16.2.8.2
16.2.8.1, 16.2.8.2
16.2.8.4, 16.2.8.5
16.2.9.2, 16.2.9.5,
16.2.9.6
16.2.9.2, 16.2.9.5,
16.2.9.6
16.2.9.3, 16.2.9.6
16.2.9.5, 16.2.9.6
16.2.3.1, 16.2.3.2,
16.2.3.6, 16.2.3.7,
16.2.3.8, 16.2.3.9,
16.2.3.12,
16.2.3.17,
16.2.3.18,
16.2.3.19
16.2.5.1, 16.2.5.3
16.2.6
10/2007
Jointsparagraph 16.2.1
Base Metalsparagraph 16.2.2
Filler Metalsparagraph 16.2.3
Positionsparagraph 16.2.4
Preheatparagraph 16.2.5
Electrical Characteristics
paragraph 16.2.7
Shielding Gas or Flux
paragraph 16.2.8
Techniqueparagraph 16.2.9
a/
SMAW
16.2.1.3
16.2.2.5, 16.2.2.6,
16.2.2.9
16.2.3.14,
16.2.3.15
16.2.4.2
16.2.5.2
16.2.7.3
Welding Process
GTAW
GMAW, FCAW
SAW
16.2.1.3
16.2.1.3
16.2.1.3
16.2.2.5, 16.2.2.6, 16.2.2.5, 16.2.2.6,
16.2.2.5, 16.2.2.6,
16.2.2.9
16.2.2.9
16.2.2.9
16.2.3.15
16.2.3.15, 16.2.3.16
16.2.4.2
16.2.5.2
16.2.7.3
16.2.4.2
16.2.5.2
16.2.7.3
16.2.5.2
16.2.7.3
16.2.8.3
16.2.9.1, 16.2.9.4
16.2.9.1, 16.2.9.4
16.2.9.1, 16.2.9.4
Does not apply to procedures used to make attachment welds (other than pressure-retaining tank components) to the tank shell and heads. Applies to welds of tank heads, shells, sumps, and welds attaching
connections.
Table W10. F-Numbers for steel filler metalsgrouping of electrodes and welding rods for qualification
F-No.
1
2
3
4
4
5
6
6
6
6
6
6
6
6
Table W11. A-Numbersclassification of ferrous weld metal analysis for procedure qualification
A-No.
1
2
3
Mild Steel
Carbon-Molybdenum
Chrome (0.4% to 2%)Molybdenum
Chrome (2% to 6%)-Molybdenum
Chrome (6% to 10.5%)Molybdenum
Chrome-Martensitic
Chrome-Ferritic
Chromium-Nickel
Chromium-Nickel
Nickel to 4%
Manganese-Molybdenum
Nickel-Chrome-Molybdenum
4
5
6
7
8
9
10
11
12
a/
C
0.15
0.15
0.15
Cr
0.50
0.402.00
Analysis, Percentagea/
Mo
Ni
0.400.65
0.400.65
0.15
0.15
2.006.00
6.0010.50
0.401.50
0.401.50
1.60
1.20
2.00
2.00
0.15
0.15
0.15
0.30
0.15
0.17
0.15
11.0015.00
11.0030.00
14.5030.00
25.0030.00
0.70
1.00
4.00
4.00
0.55
0.250.75
0.250.80
7.5015.00
15.0037.00
0.804.00
0.85
1.252.80
2.00
1.00
2.50
2.50
1.70
1.252.25
0.752.25
1.00
3.00
1.00
1.00
1.00
1.00
1.00
1.50
Mn
1.60
1.60
1.60
Si
1.00
1.00
1.00
Table W12. F-Numbers for nonferrous filler metalsgrouping of electrodes and welding rods for qualification
F-No.
21
22
23
24
A-5.10
A-5.10
A-5.10
A-5.10
41
41
A-5.11
A-5.14
10/2007
13.3
Test
Joints
13.3.1 The base material, the filler metal, and the welding procedure shall comply with the appli- cable
WPS. Information regarding the essential variables in paragraph 13.2 above shall be recorded in
the facilitys PQRs prepared for each procedure qualified (See Fig. W12). The dimen- sions of
the test plates and the length of the welds shall be sufficient to provide the required test
specimens.
13.3.2
The dimension for plates used for fillet welds shall be as noted in Fig. W7B.
13.3.3 When making procedure tests for butt welds, it is recommended that consideration be given to
the effect of angular, lateral, and end restraint on the weldment. This applies particularly to
material and weld metal of 80,000 psi (552 MPa) tensile strength or higher and heavy sections
of both low- and high-tensile-strength material. The addition of restraint during welding may
result in cracking that otherwise may not occur.
13.3.4 Weld grooves for thicknesses less than 5/8 in. (15.9 mm) shall be prepared by thermal pro- cesses
when such processes are to be employed during fabrication of quenched and tempered mate- rials.
This groove preparation shall also include back gouging, back grooving, or removal of
unsound weld metal by thermal processes when this procedure is employed during fabrication.
13.4
Test
Specimens
13.4.1 Vacant
13.4.2 For procedure qualifications, the type and number of test specimens required, together with the
range of thickness qualified by a given thickness of test plate, are shown in Table W13.
13.4.3 Test specimens shall be removed in the order shown in Figs. W4B, W7B, W21A, and W21B.
13.4.4 All test specimens shall be prepared and tested and meet the requirements as prescribed in
applicable portions of paragraphs 6.0, 7.0, 8.0, 10.0, and 11.2 of this appendix.
13.4.5 The number of test plates (and sets of test specimens) required by Table W13 shall be pre- pared
and tested to provide procedure qualification that will be used in the fabrication, repair,
alteration, or conversion of AAR-approved tanks.
Table W13. Procedure qualification tests required
Range of
Thickness of
Material
Qualified by
Test Plate,a/
in. (mm)
Tension
f/
g/
h/
e/
e/
f/
4
4
5
All groove welds qualify fillet welds on any thickness of base metal.
When impact or corrosion tests are required by the tank specification, they shall be included as a requirement of the procedure qualification and taken at test plate locations as shown in Figs. W21A and W21B.
Unless restricted by Table W9 and paragraph 16.2.2.6
For aluminum alloy 6061, use Fig. W5D.
Longitudinal face-bend and longitudinal root-bend tests (Fig. W4B) may be used in lieu of side-, face-, and
root-bend tests only for testing material combinations differing markedly in physical bending properties
between the two base materials or between the weld metal and the base materials.
Required only for ferritic steels having their mechanical properties enhanced by quenching and tempering.
0.5t for nonferrous materials, but not less than 1/16 in. (1.59 mm).
For gas metal-arc welding, submerged arc welding, and gas tungsten arc welding, the thickness limitations
for production welding based on a test plate thickness, t, shall be as follows:
1. For single-pass welding, with no backing strip or against a metal or ceramic backing, the maximum thickness welded in production shall not exceed the thickness of the test plate.
2. If the test plate is welded by a procedure involving one pass from each side, the maximum thickness that may be welded in production shall be 2t, where 2t shall not exceed 2 in. (50.8 mm). If
sections heavier than 2 in. (50.8 mm) are to be welded in production, a separate test plate shall
be prepared, of a thickness not less than the thickness to be used in production.
i/
Not required for test plate thickness less than 5/8 in. (15.9 mm).
10/2007
13.5 Retests
When one or more of the test specimens in Table W13 fail to meet the requirements, a retest
may be made under the following conditions:
13.5.1 When failure of specimens can be attributed to welder performance, an immediate retest may be
made.
13.5.2 When failure of specimens can be attributed to essential variables of the WPS, make nec- essary
changes and make a new qualification test.
13.6 Renewal of Qualification
Once a welding procedure is qualified, it shall continue in effect indefinitely, within the range of its
essential variables.
13.7
Weld
Buildup
Following are the required essential variables and testing specifications that must be followed in
order to qualify a weld buildup procedure made by the temper bead technique, as described in
Appendix R, paragraph 11.5.
13.7.1
Essential
variables
The welding procedure must be set up as a new procedure and must be requalified when any of the
following changes are made:
A change from one welding process to any other process, or combination of processes
A change in base metal specified maximum chemical analysis (e.g. from ASTM A285
Grade C to ASTM A515 Grade 70) that increases the carbon equivalent. Carbon
equivalent for- mula is as follows:
C.E. = C +
M n
C r M o V
N i C u
------ -- + ----- - + ------ - + ---- + ----- + ---- -6
5
5
5 15 15
A change in the composition of the weld filler metal from one F-number to another F-number and/or from one A-number to another A-number
The addition of other welding positions than those already qualified
A decrease in the preheat temperature qualified
A decrease in the interpass temperature qualified
A change from a multiple-layer to a single-layer overlay
A decrease in the heat input under that qualified. The heat input formula is as follows:
Conventional Units
V o lt a g e
Heat input (J/in.) = ----- --- - -- --- --- --- A m p e r a g e 6 0
----- ---- ----- --- --- -- -- --- ---- ----- --- -Travel Speed (in./min)
SI Units
V o l ta g e A m
Heat input (J/cm) = ---- --- -- - --- --- ---- ----- ---- ----p e r a g e 6 0
--- --- -- -- --- ---- ----- --- -Travel Speed (cm/min)
When welding in the vertical position, a change from uphill to downhill, or vice versa
For submerged arc welding, a change in the nominal composition or type of flux used
Requalification is not required for a change in flux particle size
A change in the number of electrodes acting on the same welding puddle
The addition or omission of supplementary filler metal to the welding arc
For machine or automatic welding, the addition or elimination of oscillation of the electrode or electrodes
A change from a single gas to any other single gas, or to a mixture of gases, or vice versa; a
13.7.2 Testing
The testing plate shall be of equal or greater thickness than the base metal used in production.
The test plate shall be a minimum of 12 in. long and 6 in. wide (305 mm long and 153 mm wide).
13.7.3
Examination
13.7.3.1 The weld buildup surface shall be examined using the liquid penetrant or magnetic par- ticle
method. The examination shall meet the requirements and acceptance standards of paragraph
11.3 or paragraph 11.4 as applicable. Radiographic examination per paragraph 5.3.2 is not
required.
13.7.3.2 Following the liquid penetrant examination, four guided bend tests shall be made from the test
coupon. The test specimens shall be cut so that there are four specimens perpendicular to the
direction of welding (see Fig. W23). The bend specimen face may be ground smooth, but not
more than 1/16 in. (1.59 mm) of the overlay may be removed.
The guided bend specimens shall have no open defects in the weld or heat-affected zone exceeding
1/8 in. (3.18 mm), measured in any direction on the convex surface of the specimen after bending.
Cracks occurring on the corners of the specimen during testing shall not be considered, unless
there is definite evidence that they result from slag inclusions or other internal defects.
13.7.3.3 The first and last weld bead shall have a portion sectioned out of them to be polished, etched,
and micro-hardness tested in accord with ASTM E384. Acceptable hardness values shall not
exceed 285 HV2000 (Vickers) or 320 HK500 (Knoop). In accord with Fig. W24, a minimum of
three indentations shall be taken in the base metal, in the heat-affected zone, and in the weld
metal, a total of not less than nine indentations.
14.1
FABRICATION
14.2 Forming
Forming of plates shall be done by pressure and not by impact. This includes the edges of the
plates forming longitudinal joints.
14.3
Cutting
Size
to
14.3.1 Ferrous and nonferrous plates, edges of heads, and other parts may be cut to size and shape by
mechanical means such as machining, shearing, or grinding or by applicable thermal cut- ting.
14.3.2 Oxygen- or arc-cut edges shall be uniform and smooth and shall be free of fins, tears, cracks,
loose or thick scale, slag, surface oxides, moisture, grease, and other foreign material that would
prevent proper welding. Detrimental oxidation of material that was molten shall also be
removed. Discoloration that may remain on oxygen-cut carbon and low-alloy-steel surfaces is not
considered detrimental to welding.
14.4
Alignment
14.4.1 Plates and heads that are being welded shall be fitted, aligned, and retained in position during
the welding operation.
14.4.2 Bars, jacks, clamps, or other appropriate devices, including tack welds, may be used to hold in
alignment the edges to be welded. Temporary tack welds shall be removed.
14.4.3 The parts to be joined by fillet welds shall be brought into as close contact as practicable. The root
opening shall not exceed 3/16 in. (4.8 mm). If the separation is 1/16 in. (1.6 mm) or greater,
the leg of the fillet weld shall be increased by the amount of the separation, or the manu- facturer
shall demonstrate that the required effective weld size has been obtained.
14.4.4
10/2007
C-III [M-1002] 41
14.4
Vacan
t
14.5
Welding
Conditions
14.5.1 Welding shall not be done when the ambient temperature is lower than 0 F (17.8 C). At
temperatures between 32 F (0 C) and 0 F (17.8 C), the surface of all areas, within 3 in. (76.2
mm) of the point where a weld is to be started, shall be heated to a minimum of 50 F (10 C)
before welding is started. If the ambient environmental temperature is below 0 F [17.8 C], a
heated structure or shelter around the area being welded may maintain the temperature adjacent
to the weldment at 0 F [17.8 C] or higher.
14.5.2 Welding shall not be done when the surfaces of the parts to be welded are wet. Welding shall not
be done when rain or snow is falling or during periods of high winds, unless the welder and work
are properly shielded.
14.6 Out-of-Roundness of Shells
The shell of a completed tank of circular cross-section shall be circular within 1% of the inside
diameter of the tank at the location of measurement.
14.7 Tolerance for Heads
See Appendix E, paragraph 2.2, for permissible deviation of a head from the specified shape.
14.8 Arc Strikes
Cracks or blemishes (visible marks) caused by arc strikes shall be removed. The removal of any
cracks shall be confirmed by liquid penetrant or magnetic particle inspection; reference Appendix
T, paragraph 4.0 or 5.0, respectively.
15.1
WELD
JOINTS
15.2
Welder
Visual
Acuity
Welders are not subject to the requirements of Appendix T unless also certified to perform
nonde- structive examination in accordance with Appendix T.
15.3
15.3.1 Welders must have a documented visual acuity examination administered prior to produc- tion
welding and at a minimum once every 3 years. Welders shall be examined to ensure that they
have natural or corrected near-distance visual acuity in at least one eye such that each
individual is capable of reading a Jaeger Number 2 test chart or equivalent at a distance of
not less than 12 in.
15.3.2 Welders examined in accordance with the vision requirements of AWS QC-1, CSA 178.2, or
Appendix T meet Appendix W visual acuity requirements for welders.
15.4 Cleaning During Welding
When weld metal is to be deposited over a previously welded surface, all visible slag shall be
removed to prevent inclusion of impurities in the weld metal.
15.5
Vacan
t
15.6
Alignment
Tolerances
Alignment of sections at edges that have been butt-welded shall be such that the maximum
offset is not greater than the applicable amount listed in Table W14. Joints within tank heads
and dome heads shall meet the requirements in Table W14 for longitudinal joints.
Table W14. Alignment tolerances
Section Thickness, in. (mm)
Up to 1/2 (12.7) inclusive
Over 1/2 (12.7) to 3/4 (19.0) inclusive
Over 3/4 (19.0) to 1 1/2 (38.1) inclusive
Over 1 1/2 (38.1) to 2 (50.8) inclusive
Over 2 (50.8)
a/
15.7
Weld
Reinforcement
(Butt
Welds)
The surface of any weld metal shall be at least flush with the adjoining plate surface and may be
built up as reinforcement, which shall not exceed 3/32 in. (2.38 mm) for plates 5/8 in. (15.9 mm)
and thinner, nor 1/8 in. (3.18 mm) for thicker plates. The weld bead reinforcement shall have a
gradual transition from its maximum allowable crown to the plane of the base metal surface.
15.7.1 The reinforcement need not be removed, except to the extent that it exceeds the allowable buildup
above or does not conform with requirements of paragraphs 11.2.1 and 15.11 of this
appendix.
15.7.2 For a single-welded butt joint with backing strip, the requirements for reinforcement apply
only to the side opposite the backing strip.
15.7
Fillet
Welds
15.7.1 Concavity and convexity shall fall within the ranges shown in Table W15. Weld size of fil- let welds
shall not be below the specified size by more than 1/32 in., except that fillet welds over 3/16 in.
may be 1/16 in. undersize for up to 10% of the length of the weld.
15.7.2 Weld metal shall be deposited in such a way that adequate penetration into the base metal at the
root of the weld is secured.
15.7.3
C-III [M-1002] 43
Convexity
1/32 (0.794)
1/16 (1.59)
3/32 (2.38)
3/32 (2.38)
1/8 (3.18)
10/2007
15.8
Interrupted
Welding
If the welding is stopped for any reason, care shall be taken in restarting to ensure full
penetration to the bottom of the joint and thorough fusion between the weld metal and the base
material and to the weld metal previously deposited. All craters shall be filled.
15.9
Identification
Welds
of
15.9.1 Each welder and welding operator shall stamp his or her identifying number, letter, or
symbol, assigned by the manufacturer, adjacent to their welds made in ferrous plates 1/4 in.
(6.35 mm) and over in thickness and in nonferrous plates 1/2 in. (12.7 mm) and over in thickness.
15.9.2 For identifying welds in ferrous plates less than 1/4 in. (6.35 mm) thick and nonferrous plates
less than 1/2 in. (12.7 mm) thick, suitable stencil or other surface markings shall be used.
15.9.3 An acceptable alternative for all plate thicknesses, both ferrous and nonferrous, is for the
fabricator to keep a record of welders and welding operators employed on each joint. These records
shall be available.
15.10 Repair of Defects
Defects in welded joints shall be repaired by removing the defect and rewelding. The defect may
be removed by mechanical means, by air-carbon arc, or by plasma arc gouging.
15.11
Surface
Welds
Quality
of
15.11.1 The surface of the weld shall be free of cracks, incomplete fusion, and slag. Weld surfaces shall be
free from surface porosity. Undercut shall not be in excess of 0.010 in. and shall not reduce the
thickness below the minimum required value in the tank shell and heads. Tank car tank groove
welds shall be filled to their specified cross section.
15.11.2 Welded joints in draft sills and underframes and other components attached to the tank car tank
shall be constructed in such a manner as to limit undercut and porosity to values permit- ted by
AWS D15.1 (current edition). All welds shall be classified as Class 1 unless otherwise specified by the tank manufacturer or car owner. Undercut in tank car tanks shall be limited per
paragraph 15.11.1 of this appendix.
15.11.3 Weld spatter shall not be permitted in areas where it would interfere with the function or corrosion
protection of the tank car tank (e.g., interior coating, linings). Weld spatter that resists normal
cleaning methods (e.g., de-slagging, blasting, etc.) may be permitted.
15.12
Flux
15.12.1 Handling equipment shall be of a design, location, and support that will minimize any tendency
toward separation or segregation of flux particle size or density.
15.12.2 All containers and reservoirs used for flux shall be so designed that they will empty in normal
usage with no residue remaining.
15.12.3 Normal vacuum pickup recycling of unfused flux shall screen all particles of previously fused flux
or slag for a screen size not exceeding 10 per 1 in. (4 per 10 mm).
15.12.4 Recycling of used flux as a separate operation shall remove harmful dusts and foreign materials.
15.12.5 Where fused flux (slag) is recrushed, net recovered (including crushed) material shall be blended
with not less than 25% by weight new flux.
15.12.6 No reprocessed flux shall contain more than 10% by weight of any material of a screen size finer
than 200 mesh (79 per 10 mm).
15.12.7
15.12.8 Flux from damaged packages shall be discarded or shall be dried at a minimum tempera- ture of
500 F (260 C) for one hour before use. Flux that has been wet shall not be used.
10/2007
15.13.4
AWS/CSA Specification
AWS A5.1/CSA W48.1 Mild Steel
a/
b/
16.1
Classification
Numbera/
E70**
E70**R
E70**HZR
E7018M
E70##-X
E80##-X
E90##-X
E100##-X
E110##-X
Maximum
Atmosphere
Exposure Time
(hours)b/
4
9
9
9
4
2
1
1/2
1/2
700 F800 F
700 F800 F
700 F800 F
700 F800 F
700 F800 F
(371 C427 C)
Minimum Time at
Temperature
(hours)
2
1
1
1
1
1
WELDING DATA
Essential Variables
Joints
16.3.1.1 Vacant
16.3.1.2 The deletion of the backing in single-welded butt joint welds. Double-welded groove welds are
considered welding with backing.
16.3.1.3 A change in the edge preparation that would make a groove angle smaller, make groove root radius
smaller, make root face (land) larger, or decrease the joint root opening.
16.2.2
Base Metals
16.2.2.1 A change from a base material having one P-number to a material having another P- number.
Welding procedures must be qualified using approved tank shell material as listed in
Appendix M for each material group to be welded. See Appendix M, Table M10, for tank plate
base metals and ASME Section IX for other base metals. ASTM A612 can be used to qualify
TC128 Grade B if chemical and mechanical properties of TC128 Grade B are met.
Qualifications with AAR TC128 Grade B or ASTM A612 base metals qualify for P-1 materials,
but not vice versa. When joints are made between two base materials that have different Pnumbers, whether nonfer- rous or ferrous, a welding procedure qualification shall be made for the
applicable combination of P-numbers, even though procedure qualification tests have been made
for each of the materials welded to itself. Welding procedure qualification with a base metal in
one P-number, or P-number plus Group-number, qualifies for all other base metals in the same
M-number grouping (M-num- bers as defined by AWS D15.1). Qualifications for M-number
materials do not qualify correspond- ing P-number materials.
16.2.2.2 A change in either or both base materials from a nonferrous material shown with one P-number
in Appendix M, Table M10, to a nonferrous material shown with another P-number, or to a
nonferrous material not shown, except that a change involving only aluminum and its alloys
shown in Table M10.2 will not require requalification.
16.2.2.3
A change in base material thickness beyond the range qualified in accord with Table W7.
16.2.2.4 A change in base material thickness beyond the range qualified in accord with Table W13.
16.2.2.5 Welding procedure qualifications shall be made using a base metal of the same type or grade as
the base metal to be used in production welding. When joints are to be made between two different
base metals, a procedure qualification shall be made for the applicable combination of base
metals, even though procedure qualification tests have been made for each of the two base
metals welded to itself. If, however, the procedure specification for welding the combination of
base metals specifies the same essential variables, including electrode or filler metal, as both
specifica- tions for welding each base metal to itself, such that base metals is the only change, it
shall not be necessary to make impact tests to qualify the two together. In addition, when two
different base metals are qualified using a single test coupon, that coupon qualifies the welding
of these two to themselves, as well as to each other, using the variables qualified. In all cases,
joint tension test specimens of the PQRs must meet the requirements of paragraph 6.3.2 of this
appendix.
16.2.2.6 The minimum thickness qualified is the thickness of the test coupon T or 5/8 in.
(15.9 mm), whichever is less. However, where T is less than 1/4 in. (6.35 mm), the minimum
thick- ness qualified is 1/2T.
16.2.2.7 For single-pass or multipass welding in which any pass is greater than 1/2 in. (12.7 mm) thick, an
increase in base metal thickness beyond 1.1 times that of the qualification test coupon.
16.2.2.8 For the short-circuiting transfer mode of the gas metal-arc process, when the qualifica- tion test
coupon thickness is less than 1/2 in. (12.7 mm), an increase in thickness beyond 1.1 times that of
the qualification test coupon.
16.2.2.9
Vacan
t
10/2007
16.2.3
Filler Metals
16.2.3.1 A change from one F-number in Tables W10 and W12 to any other F-number, or to any other filler
metal not listed in Tables W10 and W12, except qualification under any F-number up to and
including F-No. 5, shall qualify a welder for all lower F-numbers.
16.2.3.2 For the ferrous metals in Table W11, a change in the chemical composition of the weld deposit
from one A-number to any other A-number in Table W11. Qualification with A-No. 1 shall qualify
for A-No. 2 and vice versa. In lieu of an A-number designation, the nominal chemical composition of the weld deposit shall be indicated on the PQR and WPS. Designation of nominal
chem- ical composition may also be by reference to the AWS classification (where such
exists), the manufacturers trade designation, or other established procurement documents.
16.2.3.3 A change from a nonferrous filler metal listed with one AWS classification number in Table
W12 to a filler metal listed with another classification number, or to any other filler metal.
16.2.3.4
16.2.3.5
flux cored
bare (solid) or metal cored
powder
16.2.3.6 The addition or deletion or change of more than 10% in volume of supplemental filler metal as
qualified.
16.2.3.7 In submerged arc welding where the alloy content of the weld metal is largely dependent upon the
composition of the flux used, any change in any part of the welding procedure that would result in
the important alloying elements in the weld metal being outside of the specification range of
chemistry given in the applicable WPS. If there is evidence that production welds are not being
made in accord with the applicable WPS, the inspector may require that a check be made on the
chemical composition of the weld metal. The check preferably shall be made on a production weld.
16.2.3.8
Vacan
t
16.2.3.9 Where the alloy content of the weld metal is largely dependent upon the composition of the
supplemental powdered filler metal, any change in any part of the welding procedure that
would result in the important alloying elements in the weld metal being outside of the specification range of chemistry given in the procedure specification.
16.2.3.10 Vacan
t
16.2.3.11 Qualification with an F-No. 2X aluminum filler metal shall qualify to weld with any other F-No.
2X filler metal.
16.2.3.12 If filler metal does not have an AWS classification that defines chemical limits, a change in
weld wire brand name or grade.
16.2.3.13 A change from one F-number in Table W10 to any other F-number, or to any other filler metal not
listed in Table W10, except that deposited weld metal using a bare rod not covered by an AWS
specification that conforms to an analysis listed in Table W11, shall be considered to be clas- sified
as F-No. 6.
16.2.3.14 A change in the nominal diameter of the electrode to over 1/4 in. (6.35 mm).
16.2.3.15 A change in the AWS specification filler metal classification, or to a weld metal or filler metal
composition not covered by these specifications.
Exception: For carbon steel, low alloy steel, and stainless steel, a change in low hydrogen
coating type having the same minimum tensile strength and chemical analysis.
16.2.3.16 A change in FCAW filler metal brand name or grade, unless the AWS specification requires
Charpy properties equal to the required values in the relevant postweld heat treated con- dition.
16.2.3.17 A change in
the indicator for minimum tensile strength (e.g., the 7 in F7A2-EM12K) when the
flux/wire combination is classified by AWS specifications.
either the flux trade name or wire trade name when neither the flux nor the wire is classified by AWS specifications.
the flux trade name for A-No. 8 deposits.
16.2.3.18 When a filler metal with a minimum required tensile strength less than the base metal is used,
the filler metal brand and grade must be essential variables.
16.2.3.19 The omission
inserts.
16.2.4
or
addition
of
consumable
Positions
16.2.4.1 The addition of welding positions other than those already qualified. See paragraph 10.6 above.
16.2.4.2 A change from any position to the vertical position, uphill progression. Vertical-uphill
progression qualifies for all positions. In uphill progression, a change from stringer bead to weave
bead.
16.2.4.3 A change from uphill to downhill, or from downhill to uphill, in the progression specified for any
pass of a vertical weld.
16.2.5
Preheat
16.2.5.1 A decrease of 100 F (37.8 C) or more in the minimum specified preheating temperature of the
qualification test. The minimum temperature for welding shall be specified in the WPS. See
paragraph 14.5.1 in this appendix.
16.2.5.2 An increase of more than 100 F (37.8 C) in the maximum interpass temperature recorded on the
PQR.
16.2.5.3 For a preheat temperature of 32 F (0 C) or lower, the PQR test temperature is the min- imum.
16.2.6
Postweld
heat
treatment
A change in the postweld heat treatment temperature and time cycle range specified for ferrous
materials. The time cycle may be specified as varying with thickness and with time at temperature. For example: 1 hour per inch (1 hour per 25.4 millimeters) of thickness; and as shown in
Table W17.
16.2.7
Electrical
Characteristics
16.2.7.1 A change from spray arc, globular arc, or pulsed arc to short-circuiting arc, or vice versa.
16.2.7.2 A change from AC to DC, or vice versa. In DC welding, a change from direct current elec- trode
negative (straight polarity) to direct current electrode positive (reverse polarity), or vice versa.
10/2007
C-III [M-1002] 53
16.2.7.3 A change in the type of current or polarity, an increase in heat input, or an increase in volume of
weld metal deposited per unit length of weld, over that qualified. The increase may be measured
by either of the following:
16.2.7.3.1 Heat input
Conventional Units
V o lt a g e
Heat input (J/in.) = ----- --- - -- --- --- --- A m p e r a g e 6 0
----- ---- ----- --- --- -- -- --- ---- ----- --- -Travel Speed (in./min)
SI Units
V o l ta g e A m
Heat input (J/cm) = ---- --- -- - --- --- ---- ----- ---- ----p e r a g e 6 0
--- --- -- -- --- ---- ----- --- -Travel Speed (cm/min)
16.2.7.3.2 A change in volume of weld metal means an increase in bead size, or a decrease in length of
weld bead, per unit length of electrode.
The requirement for measuring the heat input or volume of deposited weld metal does not
apply when the procedure specification is qualified with a grain refining austenitizing heat
treatment after welding.
16.2.7.4
Vacant
16.2.8
16.2.8.1 A change from a single gas to any other single gas or to a mixture of gases, or a change in specified
percentage composition of gas mixture.
16.2.8.2
16.2.8.3
16.2.8.4 A change in flux involving either addition or deletion of any material of screen size finer than 200
mesh (79 per 10 mm).
16.2.8.5
16.2.9
16.2.9.1 A change in width, frequency, or dwell time of oscillation for machine or automatic weld- ing only.
16.2.9.2
In machine welding, a change from single arc to multiple arc, or vice versa.
16.2.9.3
Vacan
t
16.2.9.4 A change from single electrode to multiple electrode, or vice versa, for machine or auto- matic
welding only.
16.2.9.5
Vacan
t
16.2.9.6 A change from one welding process to any other welding process or combination of weld- ing
processes.
17.1
17.2
General
17.2.1 Postweld heat treatment, when required, shall be done before the final hydrostatic test, after any
repairs to welding, and after all attachments to be welded to the tank shell or heads have been
welded in place.
17.2.2 Minimum temperatures required by this section shall be temperatures of plate material of shell and
heads of the tank.
17.2.3 Thickness referred to as controlling the heating rate and holding time shall be the metal
thickness of the thickest shell or head plate in the tank.
17.2.4 Tank shell and head material shall determine postweld heat treatment requirements. See
Appendix R, paragraph 25.0.
17.2
17.2.1 The tank shall preferably be postweld heat treated as a unit in an enclosed furnace.
17.2.2 A tank may be postweld heat treated in more than one heat in a furnace, provided the overlap
of the heated sections of the tank is at least 5 ft (1520 mm).
Any portion of the tank outside the furnace shall be shielded so that the temperature gradient is
not harmful to the tank.
17.3
17.3.1 The furnace shall be designed to prevent direct flame impingement on the tank being heated.
17.3.2 During the heating, holding, and cooling periods, the furnace atmosphere shall be con- trolled to
avoid excessive oxidation of the tank surface.
17.3.3 The temperature of the furnace shall not exceed 800 F (427 C) at the time the tank or part is
placed in it.
17.3.4 Above 800 F (427 C), the rate of heating shall be not more than 400 F per hour divided by the
tank thickness in inches, but in no case more than 400 F (204 C) per hour.
17.3.5 During the heating period, there shall be no greater variation in temperature throughout the
portion of the tank being heated than 250 F (139 C) within any 15-ft (4570-mm) interval of
length.
17.3.6 During the holding period, there shall be no greater difference than 150 F (83.3 C)
throughout the portion of the tank being heated, except when a smaller difference is specified for a
specific material.
17.3.7 Above 800 F (427 C), cooling shall be done in a closed furnace or cooling chamber, or in still air,
at a rate not greater than 500 F per hour divided by the tank thickness in inches, but in no case
more than 500 F (260 C) per hour. Below 800 F (427 C), the tank may be cooled in still air or
in a cooling chamber.
17.3.8 Holding temperatures and/or holding times in excess of the minimum values specified in this
section for specific types of materials may be used, except when otherwise specified, for a specific material.
17.4
10/2007
17.4.1 When it is impractical to postweld heat treat at the minimum temperature of 1100 F (593 C),
any of the lower temperatures and corresponding longer times shown in Table W17 may be used.
Table W17. Permissible postweld heat treatment time-temperature combinations
Metal Temperaturea/
F
1050
1000
950
900
a/
b/
C
566
538
510
482
Holding Time
Hours per 1 in. (25.4 mm) of Thicknessb/
2
3
5
10
For intermediate temperature, the holding time shall be determined by straight-line interpolation.
The holding times shown are minimum for thickness less than 1 in. (25.4 mm).
17.4.2 Nickel-clad tanks shall not be heated to a temperature exceeding 1200 F (649 C) and shall be
heated in an atmosphere essentially free of sulfur.
17.4.3 Type 304L- or 316L-clad tanks shall not be heated to a temperature exceeding 1050 F (566 C).
17.5
17.6.1 Unless otherwise provided in the specifications for a tank, and except as required in
paragraph 17.6.2 below, all tanks fabricated from materials in Appendix M, Table M10.7, shall be
postweld heat treated as required for carbon steel tanks in paragraph 17.4 above.
17.6.2 When the base material has been heat treated by tempering, the maximum postweld heat
treatment shall be at least 50 F (27.8 C) below the tempering temperature.
17.7
17.7.1 Tanks fabricated from aluminum and its alloys shall not be postweld heat treated.
17.7.2 Tanks fabricated from nickel are not required to be postweld heat treated. Nickel tanks, if heat
treated, shall not be heated to a temperature exceeding 1200 F (640 C) and shall be heated in an
atmosphere essentially free of sulfur.
17.8
7)
17.8.1 Unless otherwise provided in the specifications for a tank, all tanks fabricated from materials in Appendix M, Table M10.5, shall be postweld heat treated in the temperature range
1025 F to 1085 F (552 C to 585 C) for a period of two hours, plus one hour for each 1 in.
(25.4 mm) of tank thickness over 1 in. (25.4
mm).
17.8.2 In lieu of the requirements of paragraph 17.3.7 above, the cooling rate from 1025 F
(552 C) to 600 F (316 C) shall be a minimum of 300 F (167 C) per hour in air or water.
17.9
QUALITY ASSURANCE
INSPECTION REQUIREMENTS
19.2
General
19.2.1 Unless otherwise provided in a tank specification, the requirements of this section shall apply.
For the purposes of this section, "inspection" refers to either radiography (RT) or ultrasonic testing
(UT).
19.2.2 All rewelded or repaired areas shall be re-examined by the original nondestructive test method
that discovered the defect.
19.2.3 All radiographic examinations shall be made using the technique and acceptance stan- dards of
paragraph 11.2 above.
19.2.4 All ultrasonic examinations shall be made using the technique and acceptance standards of
paragraph paragraph 11.5 above, provided the process is automated. Automated scanning is the
relative displacement of the ultrasonic beam and the material being tested by other than manual
means. Manual ultrasonic inspection methods are prohibited for initial inspection of tanks constructed in groups per paragraph 19.3.
19.2
19.2.1 The entire length of the following double-welded butt joints shall be inspected:
19.2.1.1 All longitudinal and circumferential joints of a tank, except circumferential joints in a multi-unit
tank car tank need not be radiographed or ultrasonically inspected.
19.2.1.2 The joint between the shell and certain types of fittings used to provide a reinforced opening.
See Appendix E, Fig. E20.2.
19.2.2 The entire length of a single-welded butt joint with backup shall be inspected when it is used, in
combination with less than a full fillet weld, to attach the interior heads of compartment tanks.
See Appendix E.
19.2.3
Vacan
t
10/2007
19.3
19.3.1 When a series of carbon steel or high alloy steel tanks made in accord with DOT 179.200 or DOT
179.220, using the same material specifications grouping and welding procedures, are being
welded in succession, all double-welded butt joints in each weld joint category must be
inspected in accord with paragraph 19.2.1 above, except as follows:
19.3.2
Weld
Category
Joint
19.3.2.1 The double-welded butt joints in the tanks may be categorized with respect to WPS, welding
operator, and welding machine. Accordingly, the double-welded butt joints in a tank may be
placed in one or more categories.
19.3.2.2 Welds in each category shall be treated independently of welds in other categories, and acceptance
or rejection and requirements for complete radiography of welds in one category shall have no
effect on welds in other categories.
19.3.3 If, in the first 3 tanks in the initial series of 20 tanks, there are no more than two unac- ceptable
defects in any circumferential joint, nor more than one unacceptable defect in any 15-ft (4570mm) longitudinal joint, then for the next 17 tanks, only the intersections of the longitudinal and
circumferential double-welded butt joints need be inspected. The two unacceptable defects in a
circumferential joint must be separated by no less than 10 times the shell thickness of the thinner member to qualify for this exception.
19.3.4
Inspection of Intersections
19.3.4.1 An inspection of an intersection shall include at least 6 in. (152 mm) of the longitudinal joint and at
least 2 in. (50.8 mm) of the circumferential joint on each side of the intersection.
19.3.4.2 When a weld joint contains an unacceptable defect, inspection of a 6-in. (152-mm) length of the
weld joint in question, on each side of the defective weld area, is required.
19.3.4.3 If the welds adjacent to the defective welds are acceptable, then the tank welding in question
shall be deemed acceptable, and the defective welds shall be repaired and inspected until they are
acceptable.
19.3.4.4 If the welding of the adjacent areas does not comply with the acceptance standards, then all doublewelded butt joints in that weld category in the tank, as well as in the two successive tanks,
shall be inspected throughout their entire length. These three tanks shall be considered the first of
an initial series with respect to that category only, and the inspection examination proce- dure
shall revert to that specified in paragraph 19.3.1 above.
19.3.5
Succeeding tanks
19.3.5.1 In each successive series of 20 tanks, only the intersections of the longitudinal and circumferential double-welded butt joints need be inspected, except that one tank, selected at random by the inspector, shall be inspected in accordance with paragraph 19.2.1 above.
19.3.5.2 If there are no more than two unacceptable defects in any inspected circumferential joint, nor
more than one unacceptable defect in any 15-ft (4570-mm) length of inspected longitudi- nal joint,
then for the remaining tanks in the series, only the intersections of the longitudinal and
circumferential double-welded butt joints need be inspected. The two unacceptable defects in a circumferential joint must be separated by no less than 10 times the shell thickness to qualify for this
exception.
19.3.5.3 If defects exceed those in paragraph 19.3.5.2 above, then the tank shall be treated as the first in an
initial series of 20 tanks, and the inspection procedure shall revert to that specified in paragraph
19.3.1 above.
TANK SHELL
TEST PLATE
TEST PLATE
REINFORCING BARS
TANK
SHELL
THIS PIECE
DISCARD
TEST SPECIMENS
CORROSION
GUIDED-BEND SPECIMEN
GUIDED-BEND SPECIMEN
Sufficient length to
provide required specimens
T
REDUCED-SECTION TENSION
DISCARD
THIS PIECE
Guided-Bend Specimens
Allow additional material as shown
in Fig. W4A when dissimilar
materials used permit longitudinal
face- and root-bend specimens.
10/2007
TANK SHELL
TEST PLATE
TEST PLATE
REINFORCING BARS
TANK
SHELL
THIS PIECE
DISCARD
TEST SPECIMENS
CORROSION
GUIDED-BEND SPECIMEN
GUIDED-BEND SPECIMEN
REDUCED-SECTION TENSION
DISCARD
THIS PIECE
Sufficient length to
provide required specimens
Guided-Bend Specimens
Allow additional material as shown
in Fig. W4A when dissimilar
materials used permit longitudinal
face- and root-bend specimens.
Note: All dimensions in mm. Appendix H must be followed when using SI units.
10 approximately
%"
On ferrous material
these edges may be
flame cut
Edge of widest
face of weld
%"
Weld reinforcement shall
be machined flush with
base material
2 R
W = 1 1/2 0.01 , if t
does not exceed 1
%" Minimum
W = 1 0.01 , if t
exceeds 1
C
WELD
B
A
L
(b)
0.353 Specimen
(c)
0.252 Specimen
(d)
0.188 Specimen
See Note 4
See Note 4
See Note 4
See Note 4
1 3/8 approx.
1 1/8 approx.
7/8 approx.
1/2 approx.
3/4
1/2
3/8
1/4
Ddiameter
0.500 0.010
0.350 0.007
0.250 0.005
0.188 0.003
Rradius of fillet
3/8 minimum
1/4 minimum
3/16 minimum
1/8 minimum
NOTES:
1.
2.
3.
4.
5.
Use maximum diameter specimen (a), (b), (c), or (d) that can be cut from test plate.
Weld should be in center of reduced section.
Where only a single specimen is required, the center of the specimen should be cut midway between the surfaces.
Reduced section A should be not less than width of weld plus two D in length.
The ends may be of any shape to fit the holders of the testing machine in such a way that the load is applied axially.
10/2007
254 approximately
6.35
Edge of widest
face of weld
On ferrous material
these edges may be
flame cut
6.35
50.8 R
W = 37.9 to 38.3 if t
does not exceed
25.4
6.35 minimum
W = 25.2 to 25.6 if t
exceeds 25.4
C
WELD
B
A
L
Note: All dimensions in mm. Appendix H must be followed when using SI units.
(b)
8.97 Specimen
(c)
6.40 Specimen
(d)
4.78 Specimen
See Note 4
See Note 4
See Note 4
See Note 4
35 approx.
29 approx.
22 approx.
13 approx.
19.0
12.7
9.52
6.35
Ddiameter
12.45 to 12.95
8.72 to 9.06
6.23 to 6.47
4.70 to 4.85
Rradius of fillet
9.82 minimum
6.38 minimum
4.76 minimum
3.18 minimum
NOTES:
1.
2.
3.
4.
5.
Use maximum diameter specimen (a), (b), (c), or (d) that can be cut from test plate.
Weld should be in center of reduced section.
Where only a single specimen is required, the center of the specimen should be cut midway between the surfaces.
Reduced section A should be not less than width of weld plus two D in length.
The ends may be of any shape to fit the holders of the testing machine in such a way that the load is applied axially.
L
B
A
G
R
WELD
D
C
METAL
0.353
0.252
2 1/4
1 3/4
1 1/4
1 3/8
1 1/8
7/8
3/4
1/2
3/8
0.500 0.010
0.350 0.007
0.250 0.005
Ggauge length
2.000 0.005
1.400 0.005
1.000 0.005
3/8
1/4
3/16
Loverall length,
approx.b/
b/
If desired, the length of the reduced section may be increased to accommodate an extensometer of any convenient
gauge length. Reference marks for measurement of elongation should, nevertheless, be spaced at the indicated gauge
length, G. The gauge marks may be made with center punch, scribe, multiple device, or drawn with ink. They shall
be light, sharp, and accurately spaced.
Other types of ends may be used, but should fit the holders of the testing machine in such a way that the load is
applied axially.
10/2007
C-III [M-1002] 65
L
B
A
G
R
WELD
D
C
METAL
Note: All dimensions in mm. Appendix H must be followed when using SI units.
8.97
6.40
57.2
44.4
31.8
35
29
22
19.0
12.7
9.52
12.45 to 12.95
8.72 to 9.06
6.23 to 6.47
Ggauge length
50.68 to 50.92
35.44 to 35.68
25.28 to 25.52
Loverall length,
approxb/
127
127
127
9.82
6.38
4.76
NOTES:
a/
b/
If desired, the length of the reduced section may be increased to accommodate an extensometer of any convenient
gauge length. Reference marks for measurement of elongation should, nevertheless, be spaced at the indicated gauge
length, G. The gauge marks may be made with center punch, scribe, multiple device, or drawn with ink. They shall be
light, sharp, and accurately spaced.
Other types of ends may be used, but should fit the holders of the testing machine in such a way that the load is
applied axially.
WELD
THIS
DISCARD
LONGITUDINAL
BEND SPECIMEN
ROOT-
TENSION
SPECIMEN
REDUCED-SECTION
BEND
LONGITUDINAL
SPECIMENFACE-
LONGITUDINAL
BEND SPECIMENROOT-
TENSION
SPECIMEN
REDUCED-SECTION
BEND
LONGITUDINAL
SPECIMENFACE-
THIS
DISCARD
ROOT-BEND
R = 1/8 in. max
T (in.)
Materials in
All Other
R
R
Table M10.2 Materials
TT t
t
1/161/8
t
t
6" MINIMUM
1/83/8
1/8
t
Weld reinforcement and backing strip, if any, shall
LF
LR
be removed flush with the surface of the specimen.
Over 3/8
1/8
3/8
SKETCH B: LONGITUDINAL FACE-BEND AND LONGITUDINAL ROOT-BEND SPECIMENS
WELD
1 Y"
t (in.)
THIS
WELD
DISCARD
LONGITUDINAL
BEND SPECIMENROOT-
TENSION
SPECIMEN
REDUCED-SECTION
BEND
LONGITUDINAL
SPECIMENFACE-
LONGITUDINAL
BEND SPECIMEN
ROOT-
TENSION
SPECIMEN
REDUCED-SECTION
BEND
LONGITUDINAL
SPECIMENFACE-
DISCARD
THIS
Fig. W4 Test plate and guided-bend test specimens for dissimilar metals
ROOT-BEND
R = 3.18 max
WELD
152 MINIMUM
Weld reinforcement and backing strip, if any, shall
be removed flush with the surface of the
specimen.
38.1
R
TT t
LF
LR
t (mm)
1.59 to 3.18
3.18 to 9.52
Over 9.52
T (mm)
Materials in
All Other
Table M10.2
Materials
t
t
3.18
t
3.18
9.52
Fig. W4.1 Test plate and guided-bend test specimens for dissimilar metalsSI units
10/2007
C-III [M-1002] 67
"t"
(inches)
1/16 - 1/8
ASTM B 209
ALLOY 6061
1/8 - 3/8
1/8
Over 3/8
3/8
1/8
FERROUS AND
NONFERROUS (a/)
MATERIALS
t
Over 1 1/2
b/
Note a/ Except Alloy 6061
ASTM B 209
ALLOY 6061
t
1 1/2
SKETCHD-SIDE-BENDSPECIMEN
FOR ASTM B 209 ALLOY 6061: This specimen to be the same as Sketch C
except for specimen thickness and corner radius. The finished thickness shall
be 1/8 rather than 3/8 and the radius shall be 1/16 max. rather than 1/8 max.
"t"
(mm)
ASTM B 209
ALLOY 6061
1.59 to 3.18
3.18 to 9.52
3.18
Over 9.52
9.52
3.18
FERROUS AND
NONFERROUS (a/)
MATERIALS
9.52 to 38.1
over 38.1
b/
Note a/ Except Alloy 6061
ASTM B 209
ALLOY 6061
t
38.1
SKETCHD-SIDE-BENDSPECIMEN
FOR ASTM B 209 ALLOY 6061: This specimen to be the same as Sketch C
except for specimen thickness and corner radius. The finished thickness shall
be 3.18 rather than 9.52 and the radius shall be 1.59 max. rather than 3.18
max.
10/2007
C-III [M-1002] 69
Thickness of
Specimen, (in.)
A
(in.)
B
(in.)
C
(in.)
D
(in.)
3/8a/
ta/
1/8b/
1 1/2
4t
3/4
2t
2 3/8
6t + 1/8
1 3/16a/
3t + 1/16a/
2 1/16
1 1/32
2 3/8
1 3/16b/
2 1/2
6 2/3t
1 1/4
3 1/3t
3 3/8
8 2/3t + 1/8
1 11/16c/
4 1/3t + 1/16d/
3/8c/
td/
a/
b/
c/
d/
To determine SI
dimensions, see
Appendix H,
paragraph 5.3.5
Thickness of
Specimen, (mm)
A
(mm)
B
(mm)
C
(mm)
D
(mm)
9.52a/
ta/
3.18b/
38.1
4t
19.0
2t
60.3
6t + 3.18
30.2a/
3t + 1.59a/
52.4
26.2
60.3
30.2b/
9.52c/
63.5
6 2/3t
31.8
3 1/3t
85.7
8 2/3t + 3.18
42.9c/
4 1/3t + 1.59d/
td/
a/
b/
c/
d/
10/2007
MACRO TEST
DIRECTION OF LOADING
NOTES:
1. For ferrous
materials: L =
10";
W = 3";
T = 3/16"- 1/2";
and maximum fillet size is
5/16".
T
STOP AND RESTART
WELDING NEAR THE
CENTER
3"
2. For nonferrous
materials: L = 4";
W = 4";
T = 3/16"-1/2";
and maximum fillet size is
5/16".
1"
1"
T
T
MACRO TEST
12" MIN.
NOTES:
T = MAXIMUM THICKNESS OF
BASE MATERIAL IN TANK AT POINT
OF WELDING OR 1", WHICHEVER IS
SMALLER.
1"
6" MIN.
FIVE EQUAL SECTION
6" MIN.
1"
MACRO TEST
NOTES:
DIRECTION OF LOADING
1. For ferrous
materials: L =
254;
W = 76.2;
T = 4.7- 13
and maximum fillet size is 6.35.
2. For nonferrous
materials: L = 102;
W = 102;
T = 4.76 to 9.52;
and maximum fillet size is the
same as dimension T.
MACRO TEST
NOTES:
T = MAXIMUM THICKNESS OF
BASE MATERIAL IN TANK AT POINT
OF WELDING OR 25.4, WHICHEVER IS
SMALLER.
FIVE EQUAL SECTION
10/2007
C-III [M-1002] 73
80
Axis
limits
for E
90
0
360
235
C
A 0 360
210
B
235
150
125
15
Axis limits
for A and B
Vertical
plane
P
Horizontal plane
360
Notes:
1. The horizontal reference plane is always taken to lie below the weld under consideration.
2. The inclination of axis is measured from the horizontal reference plane toward the vertical reference plane.
3. The angle of rotation of the face is determined by a line perpendicular to the theoretical face of the weld which passes through the axis of
the weld. The reference position (0 ) of rotation of the face invariably points in the direction opposite to that in which the axis angle
increases. When looking at point P, the angle of rotation of the face of the weld is measured in a clockwise direction from the reference
position (0 ).
Inclination
of Axis
Rotation
of Face
Flat
0 to 15
150 to 210
Horizontal
0 to 15
125 to 150
210 to 235
Overhead
0 to 80
0 to 125
235 to 360
Vertical
D
E
15 to 80
80 to 90
125 to 235
0 to 360
Position
90
80
Axis
limits
for E
E
D
360
80
280
150
Vertical
plane
C 360
A0
210
B
15
80
Axis limits
for A and B
P
280
360
Horizontal plane
Notes:
1. The horizontal reference plane is always taken to lie below the weld under consideration.
2. The inclination of axis is measured from the horizontal reference plane toward the vertical reference plane.
3. The angle of rotation of the face is determined by a line perpendicular to the theoretical face of the weld which passes through the axis of
the weld. The reference position (0 ) of rotation of the face invariably points in the direction opposite to that in which the axis angle
increases. When looking at point P, the angle of rotation of the face of the weld is measured in a clockwise direction from the reference
position (0 ).
Inclination
of Axis
Rotation
of Face
Flat
0 to 15
150 to 210
Horizontal
0 to 15
80 to 150
210 to 280
Overhead
0 to 80
0 to 80
280 to 360
Vertical
D
E
15 to 80
80 to 90
80 to 280
0 to 360
Position
C-III [M-1002] 75
BASE MATERIAL
BASE
MATERIAL
DIRECTION OF
ROLLING
WELD
METAL
LONGITUDINAL SPECIMEN
TRANSVERSE
SPECIMEN
WELD
PLATE SURFACE
LONGITUDINAL
SPECIMEN
TRANSVERSE
SPECIMEN
NOTES:
1.ALL NOTCHES CUT PERPENDICULAR TO
PLATE SURFACE.
2.ALL COMMENTS APPLY TO FULL SIZE OR
SUBSIZE SPECIMENS.
3.ALL COMMENTS APPLY TO TYPE A
(CHARPY V-NOTCH), TYPE B (CHARPY
KEYHOLE NOTCH), OR TYPE C (CHARPY
U-NOTCH) SPECIMENS
WELD
METAL
BASE
MATERIAL
WELD
LOCATE SPECIMEN AS NEAR PLATE SURFACE
AS PRACTICABLE. ETCH SPECIMEN AND
LOCATE NOTCH IN HEAT-AFFECTED ZONE.
SKETCH C-HEAT-AFFECTED ZONE
8 mm.
(0.315 )
0.25 mm.
(0.010 ) rad.
10 mm.
(0.394 )
L/2
VEE-NOTCH
55 mm
(2.165 )
L
10 mm.
(0.394 )
45
D = 8 mm
(0.315 )
10 mm.
(0.394 )
2 1/2 mm.
(0.098 )
10 mm.
(0.394 )
5 mm.
(0.197 )
SKETCH B-SUBSIZE CHARPY VEE-NOTCH SPECIMEN
Permissible Dimensional Variations
Cross-section dimensions
0.025 mm (0.001")
1 mm (0.039")
Angle of notch
1 degree
Radius of notch
0.025 mm (0.001")
0.025 mm (0.001")
Fig. W11 Type A Charpy (simple beam) impact test specimen dimensions
10/2007
C-III [M-1002] 77
7 1/2 mm.
(0.295 )
By:
Date:
Date:
JOINTS
Joint
Design
Backing
(Yes)
(No)
Backing Material (Type)
(Refer to both backing and retainers)
Metal
Nonfusing Metal
Nonmetallic
Other
Groove
Fillet
Specification No.
AWS No. (Class)
F-No.
A-No.
Size of Filler Metals
Deposited Weld Metal
Electrode-Flux (Class)
Flux Trade Name
Consumable Insert
Other
*Each base metal-filler metal combination should be recorded individually.
Revised 3/16/88
Page 1 of 2
WPS No.
POSITIONS
Position(s)
Rev.
Groove
Welding
Progression: Up
Position(s) of Fillet
PREHEAT
Preheat
Temperature,
Interpass
Temperature,
Preheat Maintenance
Down
Temperature Range
Time Range
GAS
Percent Composition
Gas(es)
Mixture
Flow Rate
Min.
Max.
Shielding
Trailing
Backing
ELECTRICAL CHARACTERISTICS
Current AC or DC
Polarity
Amps (Range)
Volts (Range)
(Amps and volts range should be recorded for each electrode size, position and thickness, etc.
This information may be listed in a tabular form similar to that shown below)
Tungsten Electrode Size & Type
TECHNIQUE
String
or
Weave
Orifice
or
Gas
Initial and Interpass Cleaning (Brushing, Grinding, etc.)
Method
Oscillation
Contact
Multiple
Multiple
Travel
Peening
Other
of
to
or
Single
Gouging
Work
Pass
Single
or
(per
Speed
Filler Metal
Weld
Layer(s)
Back
Tube
Process
Class
Current
Type
Diameter Polarity
Amperage
Range
Bead
Size
Cup
Voltage
Range
Travel
Speed
Range
Distance
side)
Electrodes
(Range)
OTHER
(e.g. Remarks, Comments,
Hot Wire Addition, Technique, Torch Angle, etc.)
Revised 3/16/88
Page 2 of 2
Fig. W12 Suggested format for welding procedure specification (WPS) (continued)
10/2007
Date:
JOINTS
Thickness
Diameter
Other
or
of
of
to
Test
Test
Specification
Grade
P-No.
P-No.
Coupon
Coupon
Temperature
Time
Other
GAS
Percent Composition
Gas(es)
Mixture
Flow Rate
Shielding
Trailing
Backing
ELECTRICAL CHARACTERISTICS
FILLER METALS
AWS
AWS
Filler
Weld
Size
Other
Specification
Classification
Metal
F-No.
Metal
Analysis
A-No.
of
Filler
Metal
PREHEAT
Revised 3/16/88Page 1 of 2
Volts
Electrode
Other
TECHNIQUE
Position of Groove
Weld Progression (Upward, Downward)
Other
Preheat
Interpass
Other
Current
Polarity
Amps
Tungsten
Temperature
Temperature
Travel Speed
String of Weave Bead
Oscillation
Multipass or Single Pass (per side)
Single or Multiple Electrodes
Other
Size
PQR No.
REDUCED SECTION TENSILE SPECIMEN TESTS
Specimen
No.
Width
Thickness
Ultimate
Total
Load lb.
Area
Ultimate
Unit Stress
psi
Type of
Failure &
Location
Type &
Figure Diameter
No.
in.
ULTIMATE
TENSILE
STRENGTH
Area
sq. In.
Total Load
lb.
Unit Stress
psi
YIELD
STRENGTH
(0.2%
offset) psi
ELONGATION (%)
REDUCTION
OF AREA
(%)
Result
Notch
Location
Notch
Type
Test
Temperature
Impact
Values
Percent
Shear
Lateral
Expansion
Mils
By:
Page 2 of 2
Fig. W13 Suggested format for procedure qualification record (PQR) (continued)
10/2007
Clock number
Stamp no.
Type
Thickness
Used
Qualified
Backing (metal, weld metal, welded from both sides, flux, etc.) . . . . . . . . . . . . . . . . . . . .
P-No. to P-No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filler metal specification (AWS) / Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filler metal F-No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consumable insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weld Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding position (1G, 5G, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Progression (uphill/downhill) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backing gas for GTAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GMAW transfer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GTAW welding current type/polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Result
Result
Fracture test
in. x
in. Concavity/convexity
We certify that the statements in this record are correct and that the test coupons were prepared, welded, and tested
in accordance with the requirements of Appendix W.
Organization
Date
By
in.
in.
FLAT POSITION 1G
HORIZONTAL POSITION 2G
Plate vertical.
Axis of weld vertical.
OVERHEAD POSITION 4G
Fig. W15 Positions of test plates for butt welds (joint design optional)
10/2007
C-III [M-1002] 85
Axis of Weld
Horizontal
Throat of Weld
Vertical
45
FLAT POSITION
1F
HORIZONTAL POSITION 2F
Axis of Weld
Vertical.
VERTICAL POSITION
3F
Axis of
Weld
Horizontal
OVERHEAD POSITION 4F
No. of Pores
Dimension, inches
0.10
0.031
0.0195
15
35
ASSORTED
0.10
LARGE
40
0.031
MEDIUM
0.0195
101
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY 6-IN. LENGTH OF WELD.
1/2-IN. WELD THICKNESS
TOTAL PORE AREA PERMITTED IS 0.030 SQ IN.
10/2007
C-III [M-1002] 87
No. of Pores
Dimension, millimeters
2.54
0.787
0.495
15
35
ASSORTED
2.54
LARGE
40
0.787
MEDIUM
0.495
101
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY 152 MM LENGTH OF WELD.
12.7 MM WELD THICKNESS
TOTAL PORE AREA PERMITTED IS 19.4 SQ. MM.
No. of Pores
Dimension, inches
0.024
35
0.034
19
0.125
1
ASSORTED
0.125
LARGE
0.034
50
MEDIUM
0.024
99
FINE
10/2007
C-III [M-1002] 89
No. of Pores
Dimension, millimeters
0.610
35
0.864
19
3.18
1
ASSORTED
3.18
LARGE
0.864
50
MEDIUM
0.610
99
FINE
No. of Pores
Dimension, inches
0.0275
38
0.039
21
0.125
1
ASSORTED
0.125
LARGE
0.039
50
MEDIUM
0.0275
101
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY 6-IN. LENGTH OF WELD.
1-IN. WELD THICKNESS.
TOTAL PORE AREA PERMITTED IS 0.060 SQ. IN.
10/2007
C-III [M-1002] 91
No. of Pores
Dimension, millimeters
0.698
38
0.991
21
3.18
1
ASSORTED
3.18
LARGE
0.991
50
MEDIUM
0.698
101
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY 152 MM LENGTH OF WELD.
25.4 MM WELD THICKNESS.
TOTAL PORE AREA PERMITTED IS 38.7 SQ. MM.
No. of Pores
Dimension, inches
0.039
38
0.055
21
0.125
ASSORTED
0.125
10
LARGE
0.055
51
MEDIUM
0.039
100
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY SIX INCH LENGTH OF WELD.
TWO INCH WELD THICKNESS.
TOTAL PORE AREA PERMITTED IS .120 SQ. IN.
10/2007
No. of Pores
Dimension, millimeters
0.991
38
1.40
21
3.18
ASSORTED
3.18
10
LARGE
1.40
51
MEDIUM
0.991
100
FINE
TYPICAL NUMBER AND SIZE PERMITTED
IN ANY 152 MM LENGTH OF WELD.
50.8 MM WELD THICKNESS.
TOTAL PORE AREA PERMITTED IS 77.4 SQ. MM.
DISCARD
THIS PIECE
DISCARD
SIDE-BEND
SPECIMEN
FACE-BEND
THIS PIECE
SPECIMEN
SPECIMEN
SIDE-BEND
SPECIMEN
ROOT-BEND
SPECIMEN
FACE-BEND
SPECIMEN
SIDE-BEND
THIS PIECE
WELD
SPECIMEN
SIDE-BEND
SPECIMEN
DISCARD
THIS PIECE
WELD
DISCARD
THIS PIECE
DISCARD
THIS PIECE
ROOT-BEND
SPECIMEN
FACE-BEND
SPECIMEN
SIDE-BEND
SPECIMEN
SIDE-BEND
SPECIMEN
DISCARD
THIS PIECE
DISCARD
THIS PIECE
WELD
WELD
Plug
Fillet
Stgniftc3.nce
Svm o s an
Spot or
Back or
Seam
Stud
Projection
or Slot
Backing
Flange
Flange
Corner
Edge
Arrow Stde
Other Stde
Not
Used
Beth Sides
No Arrow Side
used
Signtftcance
Not
U::;eU
Not
Used
Not
or Other Side
Not
Used
Not
Used
Not
Used
Not
Used
Not
UstJd
Not
Used
Not
Used
Not
Not
Used
Not
Used
Not
Used
Used
Groove
Locaton
Si;Jmftc3.nce
SQUARE
Scarf for
Bevel
Flare-V
Brazed Jomt
Flare-Bevel
Arrow Side
Other Stde
Bath Sides
No Arrow Side
or Other Side
Not
'ot
Used
Signtftcance
Not
Used
Used
Not
Used
Supplementary Symbols
Weld-All
Around
Field Weld
Consum-
Melt
Thru
able
Insert
Not
Not
Used
Used
Backing
Spacer
Flush
Convex
Concave
Finish sym::>ol
Contour symbol
//
"""- '\1::
f1111ng
Depth of bevel s ze or
strength for certain welds
I-----'------'-----'--B-a-s-ic...LJ-o-in_t_s __,_
,_
_,_
_,SpeclfiC8tiOn
process or
other reference
f-------l_d_e_n_t_if_ic_a_ti_o_n_o_f_A_r_ro_w_S_idre_a_n_d_O_th_e_r_S_id_e_J_o_in_t
1 AI
R
a:
:
:Sen
-1
Symbol
of Joint
rA:7 o
\
)to::::---\
/J.- )_ _
P\
18
hJ
r---
Lather S1de
of Joint
/I
L /'
T-Joint
Arrow Side
of
Arowof
Welding
Symbol
/
L
v /I. ,
o f
nce
is not used)
,.::;:::/'!!'
/.r--lN)
-+-'-----/ L
"lo o....-.ho :
Weld
mber
of
""
Lap Jo1nt
Other Side
--.........
elds
Arrow connecting
raference line
to arrow s1de
: ;_:, ife':',',
r !
"': v:r
' 0 0 - -&
-
Peference line
;:"g;t; ,o 1
<(
J-l _
l2ym.ool
OJ
A=J
_l;ieldsymbol
CI:.CI)
.\
Me
Joint
!,
/" - -
Welding
Symbol
1
Pitc1 (center-to-center
spacing) of welds
come'J""
Arrow Side
Lp
S(E)
C!Jw
scrtJoint
w: :
Arrow cf
Weldmg
Not
Used
tail
"
Edge Joint
Arrow Side
of Joint
J:.._....... I;::: \-
Process
Abbreviations
Where process abbrev1at1ons are to
be included in the tail of the weldinr;
symbcl. reference is made to
Table 1, Des1gnation of Welding
-.4
and
I'.
I/
Allied
j_f- !....
\
Other Side
o' Jo1nt
Processes by LetterS,
Arrow of
Weldmg
Symbol
1--
AllOW of
Weldmg
Symbol
Side
Member of
Joint
Joint_/
M1ami, Flonda
33135
M-1002
APPENDIXW
Weldsize'
between centers)
116
in direction or as dimensioned
3/4
Size or
2nd operation
- - _--,A
- - - -
'''
RSEW
Pitch
(?)
Size
'(_ Process
2nd operation
I"'
Size or
- - or- - - -
- 1st operation
1- - -
\\\::
Number of welds
025
acking
weld
Sac
weld
"'""C'"
Length of Increments
---------or-------
RSIN
(length of leg)
between centers)
of welds
Size_/
e
Pitch (distance
countersink
l .
(length of leg)
P1tch (distance
of increments
Size/
Size(diameter
of hole at
root)
of1n
5/16
2-5
Included angle of
Pitch (distance
Length
Number of
studs
Process
I"-
(t-t/4)
(t)l/
;>
Root_
_/
Weld_/
Root opening
SIZE
60 0
Weld size
opemng
Groove
angle
Depth of
/Weld size
bevel\
Back
gouge
\_Weld size
Complete Penetration
K7"'
v
nearest arrow
2nd operation
3rd operation
CJP
Melt-Thru Symbol
Radius\
3/64
1/16
1116
eld
Sl28
Process referenc/
w
Root
Joint with Spacer
reinforcement
Flush Contour Symbol
--
It should be Jnderstond that these charts are intended only as shop aids. Tt-.e only complete and official presentation of the standard weldng symbols is in A2.4.
M-1002
C-
APPENDIX W
M-1002
SPECIMEN
FACE-BEND
FACE-BEND
DIRECTION
OF
WELDING
SPECIMEN
FACE-BEND
SPECIMEN
FACE-BEND
SPECIMEN
1 Y" (TYP.)
MICRO-HARDNESS
SECTION
Y"
(SEE NOTE)
1 Y" MIN.
WELD
OVERLAY
1 Y"
T
BACK SIDE
NOTE: THE BACK SIDE OF THESE COUPONS MAY NEED TO BE
MACHINED TO THE Y" FACE-BEND THICKNESS
Fig. W23 Order of removal for face bends for weld overlay procedure qualification
10/2007
APPENDIX W
Fig. W24 Detail for microhardness sections for weld overlay procedure qualification
10/2007