Units and Unit Conversions Important For ENES 100

Units and unit conversions important for ENES 100
Handout prepared by Prof. Sheryl Ehrman, Fall 2008

The objective of this handout is to review the topic of units and unit conversions. Measured or
counted quantities have a numerical value (9) as well as a unit (9 of what?). As engineers, we
may have to work with several different units to describe the same measured quantity. In the
sciences, it is common to use SI (Systeme Internationale dUnites) units, but in engineering
practice, one might use the American engineering (Am. Eng) system. We may do design
calculations in SI but we have to go to a hardware store and purchase supplies and parts in Am.
Eng units. Thus, in addition to units, we need to know how to convert between them. Lets start
with reviewing these two systems of units.
Systems of units:
A table of base units is given below in Table 1:
Table 1: SI base units.
Quantity
Length
Mass
Time
Temperature
Electric current
Light intensity
Amount of substance
Unit
meter, m
kilogram, kg
second, s
kelvin, K
ampere, A
candela, cd
mole, mol
Base units in the American engineering system are the foot (ft) for length, the pound-mass (lbm)
for weight, and seconds for time. Multiple units are defined as multiples or fractions of base units.
For example a meter is a base unit, but a millimeter is a multiple unit. Commonly used prefixes
for multiple units are given for SI in Table 2. Derived units (units for pressure, force, velocity
etc..) can be obtained by multiplying and/or dividing base or multiple units. Some commonly used
derived SI units are given, with their equivalent in base units in Table 3. Units are written
following the numerical value, with a space in between the value and the unit. Five meters would
be written 5 m, not 5m.
Table 2: Prefixes used for multiples or fractions of units.
Multiple
Fractional
3
-2
kilo (T) 10
centi (c) 10
6
-3
mega (M) 10
milli (m) 10
9
-6
giga (G) 10
micro () 10
12
-9
tera (T) 10
nano (n) 10
Table 3: Commonly used derived units in SI.
Quantity
Volume
Force
Pressure
Energy, work
Power
Unit
liter
newton
pascal
joule
watt
Symbol
L
N
Pa
J
W
Equivalent in terms of base units

3
0.001 m
2
1 kg m/s
2
1 N/m
2 2
1 N m = 1 kg m /s
2 3
1 J/s = 1 kg m /s
Rules for using units in mathematical operations:

For addition and subtraction, quantities can only be added or subtracted if the units are the same.
Examples: 3 m + 9 m = 12 m, but 3 m + 900 cm = ?
In order to perform the second operation, one would have to either convert 3 m to cm or convert
900 cm to m. Think of an analogy to algebra. You can add 3x + 9x = 12x, but you cant add 3x +
900y.
For multiplication and division, though, just like algebra, you can combine units.
100 kilometers = 200 km
0.5 h
h
Unit Conversions:
The equivalence between two expressions of the same quantity but different units, say 10 mm, 1
cm and 0.01 m, can be defined in terms of a ratio:
1 cm
0.01 M
or
10 mm
1 cm
These ratios are known as conversion factors and they can be used to convert units from one to
another. They do not change the quantity since multiplying by a conversion factor is the same
thing as multiplying a number by unity. To convert a quantity expressed in one unit to another
unit, multiply the quantity by the conversion factor (new unit/old unit) so that the old units cancel
out and you are left with the new units. Unit conversions do not change the number of significant
figures (regardless of the number of significant figures in the quantities in the conversion factor!).
If you have three significant figures before converting units, you have three significant figures
afterwards.
For example, if we want to convert 185 grams to the kilograms, we can write:
1 kg
185 g x
= 0.185 kg
1000 g
or you can use the horizontal and vertical line method:
185 g 1 kg
= 0.185 kg
1000 g
If you write out all the units, you can use this as a check to make sure you have not made a
mistake. For example:
185 g 1000 g
g2
=?
= 185000
1 kg
kg
One tricky conversion factor arises with units that are raised to a power. For example to convert
2
41 square inches to cm , we can write:
2.54 cm2
2
41 in x
= 260 cm
1
in
Many students forget to square the conversion factor, especially when they are in a hurry, say
2
2
during a midterm examination. They multiply 41 in by 2.54 not 2.54 and get an incorrect
answer. Do not let this happen to you!
Weight, mass and force:
The difference between weight and mass is important and this distinction can be confusing when
we are working in both SI and Am. Eng. units. Mass is a base unit, and it is a measure of the
amount of matter in an object. Weight is a measure of the force exerted on the object by gravity.
So an objects weight might vary depending on the gravitational force (say on the moon versus on
the earth), but the mass would remain the same. Force is defined as the product of mass times
acceleration according to Newtons second law of motion. Force in terms of base units is defined
2
2
is kg m/s in SI and lbm ft/s in Am. Eng. So that we dont have to carry all of these units around
in calculations, derived units have been defined in each system, Newtons in SI and pound-force
in Am. Eng.
2
1 Newton 1 N 1 kg m/s
2
1 pound-force 1 lbf 32.174 lbm ft/s
In the Am. Eng. system, the pound-force is defined as the product of a unit mass and the
2
acceleration of gravity at sea level and 45 degree latitude, 32.174 ft/s .
The conversion factor required to convert from derived to base force units is called gc and is
defined as
for SI
gc =
for Am. Eng.
1 kg m/s2
1N
gc =
32.174 lbmft /s2

1 lb f
Pressure, gauge versus absolute:

One
important unit for this course is pressure. Pressure is defined as force per unit area. In the
American engineering system, pressure can be described using units of pounds-force per square
2
inch (psi) and in SI, the units are N/m or Pascals (Pa). It is important to distinguish between
gauge and absolute pressure. Absolute pressure is the pressure relative to vacuum (zero
pressure). However, in common practice it may be more convenient to use gauge pressure.
Typically, when you measure the tire pressure of your bike or car tire, you are measuring gauge
pressure, also known as pounds-force per square inch gauge (sometimes the symbol psig is
used). This is the pressure relative to atmospheric pressure and atmospheric pressure is the
force exerted on objects per unit area by the air around us. In other words, if your tire gauge
reads zero, there is no air pressure in your tire relative to atmospheric pressure (no air will hiss
out) and you need to think about fixing your tire. Gauge pressure Pgauge and absolute pressure
Pabsolute are related through atmospheric pressure Patmosphere by:
Pgauge =Pabsolute - Patmosphere [1]
Atmospheric pressure is not a true constant. It will depend upon elevation and weather
conditions. However, standard atmospheric pressure (1 atm) has been defined as being the
5
2
typical pressure at sea level. 1 atm = 14.696 psi = 1.01325 x 10 N/m (Pa). Also note that it
may not always be clear whether gauge or absolute pressure is being used. If you are not sure,
ask!
Measurement of pressure with manometers is discussed in your textbook in chapter 3. It is
common in engineering practice to report pressure in units equivalent to the height of liquids
(inches of water, millimeters of mercury for example). These units arose because of the use of
manometers. If someone states that the gauge pressure in the hovercraft plenum is equal to 0.2
inches of water, this is what he or she really means: The pressure inside the hovercraft plenum
is enough to support a column of water 0.2 inches high using a manometer open to the
atmosphere. In some unit conversion tables you may see units conversions reported at a
specific temperature. For example, 1 atm = 33.9 ft H2O at 4 C. This is because the density of
liquids varies slightly with temperature, so the temperature of the fluid is given with the unit
conversion. In practice, since this variation is slight and since we will be working at temperatures
at or around room temperature you do not need to adjust for density variations when you convert
between units based on liquid height.
On converting units, you can directly convert between gauge pressures of different units and you
can convert between absolute pressures of different units.
Example:
Convert 1.5 inches of water at 4 C (gauge) to Pa (gauge)
1ft 1.01325 x105 Pa

1.5 in x
= 370 Pa (gauge)
x
12 in 33.9 ft H2O
Convert 775 mm Hg at 0 C (absolute) to Pa (absolute)
1.01325 x105 Pa
775 mm Hg x
= 103000 Pa (absolute)
o
760 mm Hg at 0 C
However, if you want to convert from gauge pressure to absolute pressure you will need to add
atmospheric pressure to gauge pressure (see equation 1).
Example: convert 15.0 inches of water at 4 C (gauge) to Pa (absolute)

Step 1 convert to a common unit (I choose Pa)
Step 2 convert from gauge to absolute
Details:
Step 1
1ft 1.01325 x105 Pa

15.0 in x
= 3700 Pa (gauge)
x
12 in 33.9 ft H2O
Step 2
Rearranging equation 1,
Pgauge + Patmosphere =Pabsolute

so:
3700 Pa (gauge) + 1.01325 x105 Pa = 1.05 x 105 Pa
Further reading:
http://physics.nist.gov/cuu/Units/units.html

Units and Unit Conversions Important For ENES 100

Uploaded by

Copyright:

Available Formats

Units and Unit Conversions Important For ENES 100

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Units and Unit Conversions Important For ENES 100

Uploaded by

Copyright:

Available Formats

Units and unit conversions important for ENES 100

Handout prepared by Prof. Sheryl Ehrman, Fall 2008

Equivalent in terms of base units

Rules for using units in mathematical operations:

for Am. Eng.

32.174 lbmft /s2

Pressure, gauge versus absolute:

Pgauge =Pabsolute - Patmosphere [1]

1ft 1.01325 x105 Pa

Example: convert 15.0 inches of water at 4 C (gauge) to Pa (absolute)

1ft 1.01325 x105 Pa

Pgauge + Patmosphere =Pabsolute

You might also like