En - LEACH Routing Protocol For Wireless Sensor Network: Mr. Rajesh Halke, Mrs. Kulkarni V. A

Mr. Rajesh Halke, Mrs. Kulkarni V. A.
/ International Journal of Engineering Research and

Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 2, Issue4, July-August 2012, pp.2099-2102
En - LEACH Routing Protocol For Wireless Sensor Network

Mr. Rajesh Halke1, Mrs. Kulkarni V. A.2
Dept. of Electronics Dept. of ElectronicsJ.N.E.C.ABAD J.N.E.C.BAD
ABSTRACT
A wireless network consisting of a large
number of small sensors with low-power
transceivers can be an effective tool for gathering
data in a variety of environments like civil and
military applications. The data collected by each
sensor is communicated through the network to a
single processing center called base station that
uses all reported data to determine characteristics
of the environment or detect an event. The
communication or message passing process must
be designed to conserve the limited energy
resources of the sensors.
Leach Is Clustering based protocol that
utilizes randomized rotation of local cluster-heads
to evenly distribute the energy load among the
sensors in the network. LEACH (Low-Energy
Adaptive Clustering Hierarchy) uses localized
coordination to enable scalability and robustness
for dynamic networks, andincorporates data
fusion into the routing protocol to reduce the
amount of information that must be transferred to
the base station. But LEACH is based on the
assumption that each sensor nodes contain equal
amount of energy which is not valid in real
scenarios.
INTRODUCTION
The emerging field of wireless sensor
networks combines sensing, computation, and
communication into a single tiny device. The power
of wireless sensor networks lies in the ability to
deploy large numbers of tiny nodes that assemble and
configure themselves. Usage scenarios for these
devices range from real-time tracking, to monitoring
of environmental conditions, to ubiquitous computing
environments, to monitor the health of structures or
equipment. Wireless sensor networks have the ability
to dynamically adapt to changing environments.
Hundreds of nodes scattered throughout a field
assemble together, establish a routing topology, and
transmit data back to a collection point. The
application demands for robust, scalable, low-cost
and easy to deploy networks are perfectly met by a
wireless sensor network. If one of the nodes should
fail, a new topology would be selected and the
overall network would continue to deliver data [1, 2,
3, 4]
OBJECTIVE
The objective of this paper is to arrive at an
energy-efficient communication protocol for sensor
networks which is adaptable to non-uniform and

dynamic energy distribution among The objective of
this paper is to arrive at an energy-efficient
communication protocol for sensor networks which is
adaptable to non-uniform and dynamic energy
distribution among the sensor nodes and the changing
network configurations.
Challenge
It is important that microsensor networks be
easily deployable, possibly in remote or dangerous
environments. This requires that the nodes be able to
communicate with each other even in the absence of
an established network infrastructure. In addition,
there are no guarantees about the locations of the
sensors, such as the uniformity of placement. Events
occurring in the environment being sensed may be
time-sensitive. Therefore, it is often important to bind
the end-to-end latency of data dissemination.
Protocols should therefore minimize overhead and
extraneous data transfers. In a microsensor network,
data sensed by each node are required at a remote
base station, rather than at other nodes, and the data
are being extracted from the environment, leading to
large amounts of correlation among data signals.
Therefore, the notion of quality in a microsensor
network is very different. For sensor networks, the
end-user does not require all the data in the network
because (1) the data from neighboring nodes are
highly correlated, making the data redundant, and (2)
the end-user cares about a higher-level description of
events occurring in the environment the nodes are
monitoring.
LEACH INTRODUCTION
Wireless micro-sensor networks will enable
reliable monitoring of remote areas. These networks
are essentially data-gathering networks where the
data are highly correlated and the end-user requires a
high-level description of the environment the nodes
are sensing. In addition, these networks require ease
of deployment, long system lifetime, and low-latency
data transfers. The limited battery capacity of microsensor nodes and the large amount of data that each
node may produce translates to the need for high
application-perceived performance at a minimum
cost, in terms of energy and latency.
The application that typical microsensor
networks support is the remote monitoring of an
environment. Individual nodes' data are correlated in
a microsensor network, the end-user does not require
2099 | P a g e
Mr. Rajesh Halke, Mrs. Kulkarni V. A./ International Journal of Engineering Research and
all the (redundant) data; rather, the end-user needs a
high-level function of the data
energies and avoids the inefficiencies associated with

data replication.
NEW PROPOSALS TO ENHANCE THE

LEACH PROTOCOL
The modifications and enhancements to the
LEACH protocol as follows
Figure 1-1: The LEACH protocol for microsensor

networks.
LEACH includes adaptive, self-configuring
cluster formation, localized control for data transfers,
low-energy media access, and application-specific
data processing.
In LEACH, the nodes organize themselves
into local clusters, with one node acting as the
cluster-head. All non-cluster-head nodes must
transmit their data to the cluster-head, while the
cluster-head node must receive data from all the
cluster members, perform data aggregation
functions on the data, and transmit data to the remote
base station. Therefore, being a cluster-head node is
much more energy-intensive than being a noncluster-head node. In the scenario where all nodes are
energy-limited, if the cluster-heads were chosen a
priori and fixed throughout the system lifetime, as in
a static clustering algorithm, the cluster-head sensor
nodes would quickly use up their limited energy.
Once the cluster-head runs out of energy, it is no
longer operational.
Figure 1-2: Time-line showing LEACH operation.
ADVANTAGES
PROTOCOL
OF
THE
LEACH
There are strong motivations behind

selecting the LEACH as a baseline for our target EnLEACH protocol are:
The LEACH protocol assumes all the nodes

to be similar in their capabilities and doesnt require
the cluster head nodes to be more efficient than the
others in any respect.
It successfully distributes the energy load

over all the nodes of the sensor network by
dynamically rotating the cluster-head functionality
among the nodes.
It makes the cluster-head decision and

selection process truly distributed without requiring a
central arbitrator for these decisions.
It uses the data aggregation strategy, this

strategy help in making a judicious use of the node
2.1. Changes Proposed in Cluster Setup Phase to

handle Non-Uniform Energy Distribution
In LEACH, probability of becoming a
cluster-head is based on the assumption that all nodes
start with an equal amount of energy, and that all
nodes have data to send during each frame. If nodes
begin with different amounts of energy, the nodes
with more energy should be cluster-heads more often
than the nodes with less energy, in order to ensure
that all nodes die at approximately the same time.
2.2. Changes proposed in Data Transmission
Phase
Since failure of cluster-head is a big
problem in LEACH protocol and chances of its
failure are more in data transmission phase, because
this phase involves more energy dissipation
compared to other phases in LEACH. So a method
should be evolved where failure of cluster-head can
be conveyed to its cluster members, which will help
in saving a lot of energy of its cluster members.
En-LEACH INTRODUCTION
ENHANCED-LEACH
(En-LEACH)
protocol as the enhancements and innovations
devised in thisprotocol has
following objectives:
To handle cluster-head failure
To account for the non-uniform and

dynamic residual energy of the nodes
Protocol rounds are repeated with a periodicity Tr,
with each round consisting of the following phases.
3.1.1. Advertisement Phase
The first round (i.e. round number zero) is
started by each node calculating Threshold value (or
probability to become cluster-head) using same
method as used in LEACH protocol and comparing
the threshold value with random no (0 to 1) selected
by the node. If the threshold value is greater than the
random number chosen then the node becomes the
cluster-head for this round. Hence the probability of
becoming cluster-head in round zero is given as:
P(n) = p/(1-(p*(r
mod 1/p)))
P(n) = Energy of node/Total
Energy of the Cluster
Here p indicates optimum number of clusterhead in a round ( 5 % as suggested by LEACH) and r
denotes round number.
2100 | P a g e
Actually during Data Transmission phase of each
round every member sends data along with
information of its residual energy to their clusterhead and based on this information, the cluster-head
decides which node will become the future cluster
head. This is done by calculating the probability of
becoming cluster head as a function of node energy
divided by total energy of the cluster.
Figure 3-1: Cluster-head decision in En-LEACH

protocol
Each node that has elected itself a clusterhead for the current round broadcasts an
advertisement message to the rest of the nodes. For
this cluster-head-advertisement phase, the clusterheads use a CSMA MAC protocol, and all clusterheads transmit their advertisement using the same
transmit energy. The advertisement message contains
the following fields:
The
advertisement
message
flag
ADVERTISE_MESSAGE
Cluster-head id
Cluster-head location
3.1.2. Cluster Set-up Phase
After each node has decided to which cluster
it belongs, it must inform the cluster-head node that it
will be a member of the cluster. Each node transmits
this information back to the cluster-head again using
a CSMA MAC protocol through selection message.
The contents of the selection message are:
The
selection
message
flag
CLUSTER_SELECT_MESSAGE
Cluster-head identity
Self node id
3.1.3. Schedule Creation Phase

The cluster-head node receives all the
messages for nodes that would like to be included in
the cluster. Based on the number of nodes in the
cluster, the cluster-head node creates a TDMA
schedule telling each node when it can transmit. This
schedule is broadcast back to the nodes in the cluster.
The schedule creation broadcast message consists of
the following fields:
The
schedule
message
flag
SCHED_MESSAGE
The CDMA spreading code to be used for

communications within the cluster
The TDMA schedule consisting of N

number of {node-identity(node_id) TDMA timeslot} pairs
3.1.4. Data Transmission Phase (Steady-state
Phase)
Once the clusters are created and the TDMA
schedule is fixed, data transmission can begin. If the
nodes have data to send, they send it during their
allocated transmission time to the cluster head. The
cluster-head node must keep its receiver on to receive
all the data from the nodes in the cluster. Also in this
case each member node must keep their receiver on
to receive cluster-head status.
A data message which is sent to cluster-head consists
of the following fields:
The Data message flag DATA_MESSAGE
Identity of the source node n
Cluster-head id
Residual energy left in node n ,E(n)
The actual data if any

The cluster-head status message contain following
field:
The
message
flag
CLUSTER_HEAD_DOWN
The cluster-head id
The probability of becoming cluster-head

for each node i.e. (P(n) , node id) pair.
Where P(n) = Energy of the node/total energy of the
cluster.
3.1.5. Future Cluster-head Update Phase
If the cluster-head is alive even after data
transmission phase then it can update the probability
of each of its members becoming future cluster head
by sending following update message:
The
message
flag
CLUSTER_UPDATE_MESSAGE
Cluster-head id (its own id)
Probability of each of its members { node

id(n), P(n)} in pair.
RESULT
EN-LEACH protocol was simulated and
compared with LEACH protocol both in uniform and
non-uniform energy distribution scenario.
2101 | P a g e
4.1. Uniform Energy Distribution
Once a node runs out of energy, it is
considered dead and can no longer transmit or
receive data. For these simulations, energy is
removed whenever a node transmits or receives data.
(due to energy required for data aggregation and long

distance data transmission).
This provision is missing in LEACH protocol.
En-LEACH is more effective; producing

high level information about the environment the
nodes are monitoring in an energy-efficient way.
En-LEACH is able to handle non-uniform

energy distribution of sensor nodes which is an
important characteristic of a dynamic sensor
networks.
REFERANCES:
1.
2.
Figure 4-1: System lifetime - LEACH protocol
3.
4.
Figure 4-2: Sensors that remain alive (Non dot)

and those that are dead (dots) after 31 round for
LEACH protocol.
Clusters are indicated using
different colors
The results can be summarized as follows
The first death in En-LEACH occurs at

round 38, whereas in case of LEACH the first node
dies at round 22, hence first node death is
approximately 2 times later than the LEACH
protocol.
Also the last node death in En-LEACH

occurs much later than the last node death in case of
LEACH.
5.
6.
7.
CONCLUSION
In LEACH, there may be a case when
cluster-head chosen which having less amount of
energy as compared to its cluster member nodes,
which will result in early death of cluster-head. But
in case of En-LEACH, cluster-head depending upon
energy left in the node, hence it is bound to perform
better than LEACH.
In En-LEACH, all cluster members are kept informed
about the status of their cluster-head (whether it is
alive or dead), since the probability of failure
ofcluster-head is high during data transmission phase
8.
Malik Tubaishat and Sanjay Madria. Sensor

networks: an overview. In IEEE Potentials,
April/May 2003, Pages: 2023
Deborah Estrin, David Culler, Kris Pister
andGauravSukhatme.
Connecting
the
Physical World with Pervasive Networks. In
IEEE Pervasive Computing, Volume
1, Issue 1 (January 2002), Pages: 5969.
Berkeley, University of California, 800 node
self-organized wireless sensor network.
2001: http://today.cs.berkeley.edu/800demo/
System Architecture for Wireless Sensor
Networks:
http://www.jlhlabs.com/jhill_cs/jhill_thesis.
pdf.Wendi Rabiner Heinzelman, Anantha
Chandrakasan, and Hari Balakrishnan.
Energy-Efficient Communication Protocol
for Wireless Microsensor Networks. In
Proceedings of the Hawaii International
Conference on System Sciences, January 47, 2000, Maui, Hawaii.
Wendi
RabinerHeinzelman,
AnanthaChandrakasan,
and
HariBalakrishnan , An Application-specific
Protocol
Architecture
for
Wireless
Microsensor Networks ,in IEEE transaction
on wireless communications ,vol-1, no-4,
October
2002.
http://www.sigmobile.org/phd/2000/thesis/h
einzelman.pdf.
M. Bhardwaj and A. Chandrakasan. Power
Aware Systems, presented at the
34thAsilomar Conference on Signals,
Systems and Computers, November 2000.
X. Lin and I. Stojmenovic. Power-Aware
Routing in Ad Hoc Wireless Networks. In
SITE, University of Ottawa, TR-98-11, Dec.
1998.
J. Broch, D. Maltz, D. Johnson, Y. Hu, and
J. Jetcheva. A Performance Comparison
ofMulti-Hop Wireless Ad Hoc Netowrk
Routing Protocols. In Proc. 4th ACM
InternationalConference
on
Mobile
Computing and Networking (Mobicom'98),
October 1998.
2102 | P a g e

En - LEACH Routing Protocol For Wireless Sensor Network: Mr. Rajesh Halke, Mrs. Kulkarni V. A

Uploaded by

Copyright:

Available Formats

En - LEACH Routing Protocol For Wireless Sensor Network: Mr. Rajesh Halke, Mrs. Kulkarni V. A

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

En - LEACH Routing Protocol For Wireless Sensor Network: Mr. Rajesh Halke, Mrs. Kulkarni V. A

Uploaded by

Copyright:

Available Formats

Mr. Rajesh Halke, Mrs. Kulkarni V. A.

/ International Journal of Engineering Research and

En - LEACH Routing Protocol For Wireless Sensor Network

networks which is adaptable to non-uniform and

energies and avoids the inefficiencies associated with

NEW PROPOSALS TO ENHANCE THE

Figure 1-1: The LEACH protocol for microsensor

Figure 1-2: Time-line showing LEACH operation.

There are strong motivations behind

The LEACH protocol assumes all the nodes

It successfully distributes the energy load

It makes the cluster-head decision and

It uses the data aggregation strategy, this

2.1. Changes Proposed in Cluster Setup Phase to

To handle cluster-head failure

To account for the non-uniform and

Figure 3-1: Cluster-head decision in En-LEACH

3.1.3. Schedule Creation Phase

The CDMA spreading code to be used for

The TDMA schedule consisting of N

The Data message flag DATA_MESSAGE

Identity of the source node n

Residual energy left in node n ,E(n)

The actual data if any

The probability of becoming cluster-head

Cluster-head id (its own id)

Probability of each of its members { node

(due to energy required for data aggregation and long

En-LEACH is more effective; producing

En-LEACH is able to handle non-uniform

Figure 4-2: Sensors that remain alive (Non dot)

The first death in En-LEACH occurs at

Also the last node death in En-LEACH

Malik Tubaishat and Sanjay Madria. Sensor

You might also like