9709 s10 QP 42

w
w
ap
eP
e
tr
.X
w
om
.c
s
er
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS

General Certificate of Education
Advanced Subsidiary Level and Advanced Level
9709/42
MATHEMATICS
Paper 4 Mechanics 1 (M1)
May/June 2010
1 hour 15 minutes
*8896238783*
Additional Materials:
Answer Booklet/Paper
Graph Paper
List of Formulae (MF9)
READ THESE INSTRUCTIONS FIRST

If you have been given an Answer Booklet, follow the instructions on the front cover of the Booklet.
Write your Centre number, candidate number and name on all the work you hand in.
Write in dark blue or black pen.
You may use a soft pencil for any diagrams or graphs.
Do not use staples, paper clips, highlighters, glue or correction fluid.
Answer all the questions.
Give non-exact numerical answers correct to 3 significant figures, or 1 decimal place in the case of angles in
degrees, unless a different level of accuracy is specified in the question.
Where a numerical value for the acceleration due to gravity is needed, use 10 m s2 .
The use of an electronic calculator is expected, where appropriate.
You are reminded of the need for clear presentation in your answers.
At the end of the examination, fasten all your work securely together.
The number of marks is given in brackets [ ] at the end of each question or part question.
The total number of marks for this paper is 50.
Questions carrying smaller numbers of marks are printed earlier in the paper, and questions carrying larger
numbers of marks later in the paper.
This document consists of 4 printed pages.
UCLES 2010
[Turn over
2
1
A car of mass 1150 kg travels up a straight hill inclined at 1.2 to the horizontal. The resistance to
motion of the car is 975 N. Find the acceleration of the car at an instant when it is moving with speed
16 m s1 and the engine is working at a power of 35 kW.
[4]
v (m s1)
0.18
11
t (s)
The diagram shows the velocity-time graph for the motion of a machines cutting tool. The graph
consists of five straight line segments. The tool moves forward for 8 s while cutting and then takes
3 s to return to its starting position. Find
(i) the acceleration of the tool during the first 2 s of the motion,
[1]
(ii) the distance the tool moves forward while cutting,
[2]
(iii) the greatest speed of the tool during the return to its starting position.
[2]
7N
45
A small ring of mass 0.8 kg is threaded on a rough rod which is fixed horizontally. The ring is
in equilibrium, acted on by a force of magnitude 7 N pulling upwards at 45 to the horizontal (see
diagram).
(i) Show that the normal component of the contact force acting on the ring has magnitude 3.05 N,
correct to 3 significant figures.
[2]
(ii) The ring is in limiting equilibrium. Find the coefficient of friction between the ring and the rod.
[3]
UCLES 2010
9709/42/M/J/10
3
4
370 N
160 N
O
250 N
Coplanar forces of magnitudes 250 N, 160 N and 370 N act at a point O in the directions shown in the
diagram, where the angle is such that sin = 0.28 and cos = 0.96. Calculate the magnitude of the
resultant of the three forces. Calculate also the angle that the resultant makes with the x-direction.
[7]
P and Q are fixed points on a line of greatest slope of an inclined plane. The point Q is at a height of
0.45 m above the level of P. A particle of mass 0.3 kg moves upwards along the line PQ.
(i) Given that the plane is smooth and that the particle just reaches Q, find the speed with which it
passes through P.
[3]
(ii) It is given instead that the plane is rough. The particle passes through P with the same speed
as that found in part (i), and just reaches a point R which is between P and Q. The work done
against the frictional force in moving from P to R is 0.39 J. Find the potential energy gained by
the particle in moving from P to R and hence find the height of R above the level of P.
[4]
[Questions 6 and 7 are printed on the next page.]
UCLES 2010
9709/42/M/J/10
[Turn over
4
6
2.1 m
B
2m
Particles A and B, of masses 0.2 kg and 0.45 kg respectively, are connected by a light inextensible
string of length 2.8 m. The string passes over a small smooth pulley at the edge of a rough horizontal
surface, which is 2 m above the floor. Particle A is held in contact with the surface at a distance of
2.1 m from the pulley and particle B hangs freely (see diagram). The coefficient of friction between
A and the surface is 0.3. Particle A is released and the system begins to move.
(i) Find the acceleration of the particles and show that the speed of B immediately before it hits the
floor is 3.95 m s1 , correct to 3 significant figures.
[7]
(ii) Given that B remains on the floor, find the speed with which A reaches the pulley.
[4]
A vehicle is moving in a straight line. The velocity v m s1 at time t s after the vehicle starts is given
by
v = A(t 0.05t2 ) for 0 t 15,

B
v = 2 for t 15,
t
where A and B are constants. The distance travelled by the vehicle between t = 0 and t = 15 is 225 m.
(i) Find the value of A and show that B = 3375.
[5]
(ii) Find an expression in terms of t for the total distance travelled by the vehicle when t 15.
[3]
(iii) Find the speed of the vehicle when it has travelled a total distance of 315 m.
[3]
Permission to reproduce items where third-party owned material protected by copyright is included has been sought and cleared where possible. Every reasonable
effort has been made by the publisher (UCLES) to trace copyright holders, but if any items requiring clearance have unwittingly been included, the publisher will
be pleased to make amends at the earliest possible opportunity.
University of Cambridge International Examinations is part of the Cambridge Assessment Group. Cambridge Assessment is the brand name of University of
Cambridge Local Examinations Syndicate (UCLES), which is itself a department of the University of Cambridge.
UCLES 2010
9709/42/M/J/10

9709 s10 QP 42

Uploaded by

Copyright:

Available Formats

9709 s10 QP 42

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

9709 s10 QP 42

Uploaded by

Copyright:

Available Formats

w

UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS

READ THESE INSTRUCTIONS FIRST

This document consists of 4 printed pages.

(ii) the distance the tool moves forward while cutting,

[Questions 6 and 7 are printed on the next page.]

v = A(t 0.05t2 ) for 0 t 15,

You might also like