Sika Formol EX: Chemical Form Release Agent

Product Data Sheet
Edition 2011-10_1
Sika Formol EX
Sika Formol EX
Construction
Chemical form release agent

Product
Description
Sika Formol EX is a chemical release agent for use on both timber and steel
moulds. It is designed and formulated to function as a bondbreaker between
formwork or moulds and freshly placed concrete. Sika Formol EX offers

protection to both steel and timber formwork as it acts as a rust inhibitor and
waterproofer.
Uses
Sika Formol EX can be used with excellent effect on formwork designed to

produce all types of finishes, from fair-faced to textured. Sika Formol EX has
been found to assist in the protection of equipment used in the handling and
placing of concrete.
A thin coating on bowls, barrows, skips, shovels, etc. will make these easier to
clean and protect against corrosion.
Characteristics /
Advantages
Equally effective on both steel and timber moulds

It allows for fast and easy striking of formwork
Economical and easy to apply through conventional spray equipment
Highly stable during placement and vibration of concrete
Does not stain or contaminate the finished concrete surface
Regular use will help to reduce the incidence of rust on steel moulds
It has no unpleasant odour
Product Data
Form
Appearance / Colour
Yellowish liquid
Packaging
200 ltr drums
Storage
Storage Conditions /
Shelf Life
Unlimited if stored properly in original, unopened and undamaged packaging in

dry conditions at temperatures between +5C and +40C. Keep away from direct
sunlight.
Technical Data
Chemical Base
Oil base
Specific Gravity
~ 0.80
Sika Formol EX
1/2
Flash Point
> + 65C
System Information
Construction
Application Details
Coverage
Sika Formol EX should be applied at the following stated coverage rates to

obtain a thin and even film over the entire surface of the mould or formwork:
Timber Formwork
~ 1 ltr per 19 m (0.05 ltr/m)
Metal Formwork
~ 1 ltr per 30 m (0.03 ltr/m)
Substrate Preparation
All surfaces to be coated with Sika Formol EX must be clean and free from
grease, dirt and old concrete.
Application Instructions
Application Method /
Tools
The optimum method of application is by conventional spray equipment.

However, a brush or roller can also be used.
Any excess liquid remaining on the surface after application should be mopped
off. Allow 1 3 hours to dry before pouring concrete.
Sika Formol EX is supplied ready to use and should not be diluted.
Cleaning of Tools
Clean all tools and application equipment with water immediately after use.
Hardened and/or cured material can only be mechanically removed.
Notes on Application /
Limitations
Treated formwork should not be left exposed to heavy weathering or dust

accumulation for long periods.
New unsealed timber may initially require 2 3 coats of Sika Formol EX.
Only a thin film of the product is required to ensure maximum performance.
Excess application may cause staining.
Sika Formol EX is flammable and should not be used near naked flames.
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Health and Safety

Information
For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet
(available on request) containing physical, ecological, toxicological and other
safety-related data.
Legal Notes
The information, and, in particular, the recommendations relating to the application

and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sikas recommendations. In
practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular
purpose, nor any liability arising out of any legal relationship whatsoever, can be
inferred either from this information, or from any written recommendations, or from
any other advice offered. The user of the product must test the products
suitability for the intended application and purpose. Sika reserves the right to
change the properties of its products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be supplied on request.
Sika Singapore Pte Ltd

200 Pandan Loop, 06-02 Pantech 21
Singapore 128388
SINGAPORE
Phone: +65 6777 2811

Fax:
+65 6779 6200
e-mail: info@sg.sika.com
www.sika.com.sg
Sika Kimia Sdn Bhd

Lot 689 Nilai Industrial Estate
71800 Nilai, Negeri Sembilan DK
MALAYSIA
Phone: +606-7991762
Fax:
+606-7991980
e-mail: info@my.sika.com
www.sika.com.my
Sika Formol EX
2/2

Sika Formol EX: Chemical Form Release Agent

Uploaded by

Copyright:

Available Formats

Sika Formol EX: Chemical Form Release Agent

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sika Formol EX: Chemical Form Release Agent

Uploaded by

Copyright:

Available Formats

Product Data Sheet

Chemical form release agent

formwork or moulds and freshly placed concrete. Sika Formol EX offers

Sika Formol EX can be used with excellent effect on formwork designed to

Equally effective on both steel and timber moulds

200 ltr drums

Unlimited if stored properly in original, unopened and undamaged packaging in

Sika Formol EX should be applied at the following stated coverage rates to

The optimum method of application is by conventional spray equipment.

Treated formwork should not be left exposed to heavy weathering or dust

Health and Safety

The information, and, in particular, the recommendations relating to the application

Sika Singapore Pte Ltd

Phone: +65 6777 2811

Sika Kimia Sdn Bhd

You might also like