Types of Pumps

PUMPS
Device used to move gases, liquids or slurries.

Moves liquids or gases from lower pressure to higher pressure.
A gas pump is generally called a compressor. In very low pressure-rise
applications, the operative equipment consists of fans or blowers.
Machines which convert the mechanical energy into pressure energy
Types of Pumps
Rotodynamic pumps
Positive displacement pumps
Rotodynamic pumps (Centrifugal Pumps)
Produce a head and a flow by increasing the velocity of the liquid through
the machine with the help of a rotating vane impeller.
Radial, axial and mixed flow units.
Positive displacement pump
Operates by alternating of filling a cavity and then displacing a given volume
of liquid.
Causes a fluid to move by trapping a fixed amount of it then forcing
(displacing) that trapped volume into the discharge pipe.
Delivers a constant volume of liquid for each cycle against varying discharge
pressure or head.
Classified as:
Reciprocating pumps - piston, plunger and diaphragm
Rotary pumps - gear, lobe, screw, vane.
CENTRIFUGAL PUMPS
Uses a rotating impeller to increase the velocity of a fluid.
When a certain mass of liquid is rotated by an external torque, the rise in
pressure head of the rotation liquid takes place.
The rise in pressure head at any point of the rotating liquid is proportional to
the square of tangential velocity of the liquid at that point.
Works by the conversion of the rotational kinetic energy, typically from an

electric motor or turbine, to an increased static fluid pressure.
The rotation of the pump impeller imparts kinetic energy to the fluid as it is
drawn in from the impeller eye (centre) and is forced outward through the
impeller vanes to the periphery.
As the fluid exits the impeller, the fluid kinetic energy (velocity) is then
converted to (static) pressure due to the change in area the fluid experiences in
the volute section.
Typically the volute shape of the pump casing (increasing in volume), or the
diffuser vanes (which serve to slow the fluid, converting to kinetic energy in to
flow work) are responsible for the energy conversion.
The energy conversion results in an increased pressure on the downstream side
of the pump, causing flow.
Used for large discharge through smaller heads.
Main parts of a centrifugal pump
1. Impeller
2. Casing
3. Suction pipe with a foot valve and a strainer
4. Delivery pipe
1. Impeller
Rotating part of a centrifugal pump
Consists of a series of backward curved vanes.
Impeller is mounted on a shaft, which is
connected to the shaft of an electric motor.
2. Casing
An air - tight passage surrounding the impeller
Kinetic energy of the water discharged at the
outlet of the impeller is converted into pressure
energy before the water leaves the casing and
enters the delivery pipe.
Types of the casings
a) Volute casing b) Vortex casing
c) Casing with guide blades
a) Volute casing
Spiral type in which area of flow increases gradually.
The increase in area of flow decreases the velocity of flow.
The decrease in velocity increases the pressure of the water flowing through
the casing.
A large amount of energy is lost due to the formation of eddies in this type of
casing.
b) Vortex casing
Circular chamber is introduced between the casing and the impeller.
The loss of energy due to the formation of eddies is reduced to considerable

extent by introducing the circular chamber. The efficiency of the pump is more
c) Casing with guide blades
Impeller is surrounded by series of guide blades
mounted on a ring, which is known as diffuser.
The guide vane are designed in which a way that the water
from the impeller enters the guide vane without stock.
The area of the guide vanes increases, thus reducing the velocity of flow
through guide vanes and consequently increasing the pressure of water.
The water from the guide vanes then passes through the surrounding casing,
which is in most of the cases concentric with the impeller
3. Suction pipe with a foot - valve and a strainer
A pipe whose one end is connected to the inlet of the pump and other end dips
into water in a sump.
A foot valve which is a non return valve or one - way type of valve is fitted
at the lower end of the suction pipe.
The foot valve opens only in the upward direction.
4. Delivery pipe
A pipe whose one end is connected to the outlet of the pump and other end
delivers the water at a required height.
Working principle of multistage Centrifugal pump
Consists of two or more impellers
The impellers may be mounted on the same shaft or on different shafts.
Two important function:
a) To produce a high head - the impellers are connected in series (or on the
same shaft)
b) To discharge a large quantity of liquid - the impellers (or pumps) are
connected in parallel.
Multistage Centrifugal pumps for high head
A number of impellers are mounted in series
or on the same shaft.
The water from suction pipe enters the 1st impeller
at inlet and is discharged at outlet with increased
pressure and taken to the inlet of the 2nd impeller.
If more impellers are mounted on the same shaft,

the pressure at the outlet will be increased further.
Multistage Centrifugal pumps for high discharge
The pumps should be connected in parallel.
Each of the pumps lifts the water from a
common pump and discharges water to a
common pipe to which the delivery pipes
of each pump is connected.
Each of the pump is working against the
same head.
RECIPROCATING PUMP
Reciprocating-type pumps use a piston and cylinder arrangement with suction
and discharge valves integrated into the pump.
Mechanical energy is converted into hydraulic energy (or pressure energy) by
sucking the liquid into a cylinder in which a piston is reciprocating (moving
backwards and forwards), which exerts the thrust on the liquid and increases
its hydraulic energy (pressure energy).
The pumps can be powered by air, steam or through a belt drive from an
engine or motor.
Used for pumping highly viscous fluids including concrete and heavy oils.
Classification of reciprocation pumps
1. According to the water being in contact with one side or both sides of the piston.
i) Single - acting pump
ii) Double - acting pump.
2. According to the number of cylinders provided.
i) Single cylinder pump ii) Double cylinder pump iii) Triple cylinder pump.
Working principle of a reciprocating pump
1. A cylinder with a piston, piston rod,
connecting rod and a crank.
2. Suction pipe
3. Delivery pipe
4. Suction valve
5. Delivery valve
Working principles of double acting reciprocation pump
Slip of reciprocating pump

Difference between the theoretical discharge and actual discharge of the pump.
Q
act
Q Q
Percentage Slip= th act 100
Q th
Slip = Q
th
AIR VESSELS
Closed chamber containing compressed air in the top portion and liquid (or
water) at the bottom of the chamber.
Act like an intermediate reservoir.
i) To obtain a continuous supply of liquid at a uniform rate.
ii) To run the pump at a high speed without separation.
Cavitation in pumps
Phenomenon of formation of vapour bubbles of a flowing liquid in a region
where the pressure of the liquid falls below its vapour pressure and the sudden
collapsing of these vapour bubbles in a region of higher pressure.
When the vapour bubbles collapse, a very high pressure is created.
The metallic surface, above which the liquid is flowing, is subjected to this
high pressure, which causes pitting acting on the surface.
Cavities are formed on the metallic surface and also considerable noise and
vibrations are produced.
Priming
ROTARY PUMPS
Rotary pumps are the positive displacement type pumps having circular
motion, and are without valves and can deliver a constant capacity against
variable pressure.
Pumping oils or other liquids having some lubricating qualities.
Working principles of Gear and Vane pumps
GEAR PUMP (External)

GEAR PUMP (Internal)
VANE PUMP

Types of Pumps

Uploaded by

Copyright:

Available Formats

Types of Pumps

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Types of Pumps

Uploaded by

Copyright:

Available Formats

PUMPS

Device used to move gases, liquids or slurries.

Works by the conversion of the rotational kinetic energy, typically from an

The loss of energy due to the formation of eddies is reduced to considerable

If more impellers are mounted on the same shaft,

Working principles of double acting reciprocation pump

Slip of reciprocating pump

GEAR PUMP (External)

You might also like