Ligtning Basestation

LIGHTNING EFFECTS IN BASE STATIONS OF GLOBAL SYSTEMS
FOR MOBILE COMMUNICATION

R. Markowska
remark@cksr.ac.bialystok.pl
Bialystok Technical University
Poland
A. W. Sowa
L. K. Augustyniak
a.sowa@interia.pl
Poland
Abstract: This paper presents some methods and

results of field measurements of lightning effects in a
typical base station of global system for mobile communication. A direct lightning stroke to the antenna
tower has been modelled by surge generator connected to the tower. The paper concentrates on surge
currents distributions in conducting parts of the tower
structure and the equipotential bonding system of the
container. In considerations, effects of different surge
current shapes as well as grounding system have been
also taken into account.
Keywords: lightning current distribution, lightning protection, global systems for mobile communication.
1. INTRODUCTION
It has been shown by field experiences that radio
communication stations are one of the preferential points
for direct lightning strikes. This is mainly connected with
the specific features of their construction i.e. the presence
of high communication towers and their topographical
location mostly at an open area or at hills. Moreover
there might be often limited possibilities of applying the
lightning protection elements on towers or specific conditions or requirements for grounding systems.
In most cases, serious lightning failures in radio
communication stations are caused by direct lightning
stroke either to the low voltage power line near the radio
station or to the communication tower or mast. Because
of high altitude of placing radio transmission antennas,
lightning strokes to the structures supporting the antennas
are relatively frequent.
In such a case the effects of lightning are twofold. The
lightning current flowing thorough the conducting parts
of the whole structure and associated grounding system
creates high voltage differences between conductors. This
cause a direct and very serious danger, particularly for
equipment connected to the grounding system. Some
parts of this current may flow directly through the cabling
systems into the radio-transmission equipment. On the
other hand, the same lightning current creates strong
electromagnetic pulses, which can generate large over-
laugust@cksr.ac.bialystok.pl
Poland
voltages and overcurrents in wires of electric and electronic systems.

The problem of either numerical simulations as well
as field modelling of lightning influence is quite difficult
because it is impossible to take into consideration all the
phenomena and to ensure the conditions that exist during
real lightning. However numerical simulations and field
modelling together are the most effective way for evaluation the possible effects of lightning. In field modelling,
for example, it is practically impossible to eliminate the
influence of the test circuit, but it can be estimated by
numerical simulations.
This paper presents some methods and results of investigations of surge currents distributions in conducting
elements of a typical base station for mobile communication systems. In the study a direct lightning stroke to the
antenna tower has been assumed and modelled by a surge
generator connected to the tower. The surge currents in
various points at the station have been measured.
2. MEASUREMENT TEST SETUP

The investigations were performed for a typical base
station (fig. 1) of global system for mobile communication consisted of a 50m high, 3-leg, steel tower and a
3.8m long, 2.5m wide, 3m high container. The station
was fully equipped and working.
Fig. 1. General view of the investigated base station
For simulations of a direct lightning stroke to the

tower it is necessary to inject the surge current at a higher
parts of the tower. It is, however, quite a difficult technical task to connect the surge generator to the top (50m
above ground) leading the generators conductor possibly
far away from the tower. A reliable compromise is to
connect the surge generator at relatively low altitude, up
to 20m, as it is shown in figure 2a). However it is not a
sufficient model of the lightning stroke. According to the
lightning protection zone concept this altitude meets the
boundary of protection zone already for the I protection
level (the radius of the rolling ball according to IEC
61024-1 is 20m) and is under the boundary of protection
zone for the remaining protection levels.
Another possibility is to lead the generators conductor along with the tower as it is shown in figure 2b). In
this case, in turn, the influence of the test circuit is larger.
The best way is to use a shielded cable, but for estimating
its influence by numerical simulations it is even easier to
simulate a non-shielded one.
In these investigations, for connecting the surge generator to the tower, the antenna grounding conductor (Cu
50mm2) running along the middle supporting leg of the
tower was used (see figure 2b). This grounding conductor
was isolated and connected to the antenna and the tower
structure at the top of the tower at about 45m above
ground. For the test purposes this conductor was disconnected from the grounding system at the bottom of the
tower and connected to one terminal of the surge generator directly or by 10 or 50 resistor. In this way a direct
lightning strike to the antenna was simulated.
Container
SG
3
4
4
Fence
Tower leg
Fig. 3. Test circuit layout in case of connecting the generators return conductors to the station fence
For the purposes of further numerical verifications,
the resistance of the station grounding system and the soil
resistivity were measured. The resistance of the station
grounding system with respect to remote ground, measured at the frequency of 280kHz amounts to about 6.7
and the soil resistivity was about 1600m.
Different waveforms of the test current surge with approximately double-exponential shape were used:
- 12/50s/210A or 8/50s/84A for scenario (1);
- 1.2/50s/16A for scenario (2).
a)
Antenna grounding
conductor
Surge
generator
Container
For possible equal distribution of the test current in

the earth, four separate return conductors were used to
connect the other terminal of the surge generator to four
points around the station. Two scenarios of connecting
the other terminal of the surge generator were considered:
(1) The other terminal of the surge generator was connected by four isolated conductors (Cu 10mm2) to
four points of the station fence at which the fence
was connected to the grounding system (see figures 3
and 6).
(2) The other terminal of the surge generator was connected by four isolated conductors (Cu 10mm2) to
four 75cm steal rods driven into the ground in some
distance behind the station fence (figure 4).
SG
2
1
b)
1
SG
Antenna grounding
conductor
Container
3
4
2
Surge
generator
SG
Container
Fig. 2. Various means of connecting the surge generator

to the tower
Tower leg
Fence
Fig. 4. Test circuit layout in case of connecting the generators return conductors to 4 steal rods driven into the
ground in some distance behind the station fence
For currents measurements, Tektronix probes P6021

of a band of 8.5 kHz 100 MHz were used and the data
were registered by the 100 MHz oscilloscope
HP 54600B connected to the computer. The measurement
equipment is shown on figure 5.
35
30
25
20
A 15
10
5
0
-5
-40 -20
20
40 60 80 100 120 140 160

microseconds
Fig. 7. Measured time domain current in the towers leg

no 2
Fig. 5. Surge current measurements in equipotential

bonding system of the container
Further, some currents in grounding conductors at the

entry of the antenna cables to the container were also
measured. The results are presented in figures 8 and 9.
An equipotential bonding conductor and six antenna
cable grounding conductors are connected to the groundbar at the entry to the container. The equipotential
grounding conductor links the middle leg of the tower
with the ground-bar, which is connected directly to the
grounding system at the entry to the container as it is
shown in figure 8. This figure presents also the measured
amplitudes of surge currents in one of the antenna cable
grounding conductors, in the equipotential bonding conductor and in the grounding conductor of the ground-bar.
The time domain current in the equipotential bonding
conductor is shown in figure 9.
Antenna
cable
3. MEASURED RESULTS FOR SCENARIO (1)

Figure 6 presents an overall top view of the base station together with the test circuit layout for scenario (1).
On the figure, the measured amplitudes of surge currents
in the terminals of the surge generator as well as currents
flowing to the grounding system from the towers legs at
the base of the tower are marked. As it is seen from the
figure the currents distribution is very unequal. Example
time domain current measured at the towers leg no 2 is
presented in figure 7.
55.3 A
1.53 A
Ground-bar
-2.1 A
10.9 A
Container
Equipotential
bonding
conductor
Fig. 8. Amplitudes of surge currents in one of the antenna

cable grounding conductors and in equipotential bonding
conductors at the entry to the container
47.5 A
1
SG
32.2 A
0.5
210A
66.9 A
Container
4
4
-0.5
22.2 A
2
53.4 A
Tower leg
-1
-1.5
37.2 A
Fence
-2
Fig. 6. Test circuit layout and the measured current distributions for scenario (1)
-2.5
-20
20
40
60 80 100 120 140 160 180

microseconds
Fig. 9. Time domain current in equipotential bonding

conductor at the entry to the container (see fig. 8)
The general view on currents distribution in equipotential bonding system inside the container is presented in
figure 10 (the amplitudes of surge currents) and an example time domain current in grounding conductor of the
exchange equipment is shown in figure 11.
Storage
batteries
Alarms
1.36 A
-0.36A
Power supply
Rack
8.12 A
2.28 A
27.2 A
8.56 A
1.24 A
Equipotential
bonding strap
Exchange
equipment
7A
Door-frame
connection
Fig. 10. Surge currents distribution in equipotential bonding system of the container
7
6
5
4
3
2
1
0
-20
20
40
60 80 100 120 140 160 180

microseconds
Fig. 11. Time domain surge current in grounding conductor of the exchange equipment
It is seen from figure 8 that the total current drained
off to the grounding system from the antenna cables coating at the entry to the container amounts to about 5.2% of
the total current injected into the top of the tower. About
3.3% of the total current flows into the container thorough the antenna cables coating.
Relatively high current (about 3.9%) flows to the
main ground-bar inside the container from the copper
equipotential bonding strap running along three walls of
the container. In spite of the equipment connected to this
strap as it is shown in figure 10, there was a cable rack
running under the ceiling about 0.5m above the strap,
which was as well connected to this strap at three points.
Relatively high current (4% of the total current) flows
also to the main ground-bar from the power supply.
4. CONCLUSIONS
In this paper the methods of investigation of surge
currents distributions in conducting elements of a typical
base station of global systems for mobile communication

have been presented. In considerations various ways of
modelling a direct lightning strike to the tower have been
taken into account. The direct lightning stroke to the
antenna tower has been modelled by a surge generator
connected to the tower.
For obtaining possibly equal distribution of the surge
currents in the earth, four return conductors of the generator were used during the measurements. These conductors
were connected according to two different scenarios for
the purpose of evaluating the influence of the soil. In
scenario (1) these conductors were connected to the station fence at points where the fence is connected to the
grounding system and in scenario (2) the generator return
conductors were connected to four steel rods driven into
the ground in some distance behind the station fence.
Some field measurement results in the investigated
base station for scenario (1) have been also presented.
The surge currents in various points at the station
have been measured. Up to about 4% of the total surge
current might flow to the main ground-bar from particular
piece of equipment inside the container. The total current
flowing to the ground from the main ground-bar of the
container amounts to over 13% of the total surge current.
The measured results will further be the basis for verification of numerical simulations of lightning effects in
order to evaluate the simulation methods and to extend
these methods for the cases that cannot be modelled experimentally.
REFERENCES
[1] CCITT Recommendation K 27, Bonding configuration and earthing inside a telecommunication building, ITU 1992.
[2] IEC 61024-1: International Standard., Protection of
structures against lightning Part 1: General principles.
[3] IEC 61312-1:1995 International Standard., Protection
against lightning electromagnetic impulse Part 1:
General principles.
[4] Markowska R., Lightning currents and electromagnetic fields in large radio communication centres
with towers, XI International Conference on Electromagnetic Disturbances, pp. 9.5-1 9.5-6, Bialystok, Poland, 1921 September 2001.
[5] Markowska R., Sowa A. W., Augustyniak L. K.;
Overvoltages and impulse electromagnetic fields in
broadcasting stations during direct lightning stroke,
16th International Wroclaw Symposium and Exhibition on Electromagnetic Compatibility, part 2, pp.
495500, Wroclaw, Poland, 2528 June 2002.
[6] How to Engineering guide: Lightning transient
study of a communication tower Safe Engineering
Services & Technologies Ltd., Montreal Canada.

Ligtning Basestation

Uploaded by

Copyright:

Available Formats

Ligtning Basestation

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ligtning Basestation

Uploaded by

Copyright:

Available Formats

LIGHTNING EFFECTS IN BASE STATIONS OF GLOBAL SYSTEMS

FOR MOBILE COMMUNICATION

Abstract: This paper presents some methods and

voltages and overcurrents in wires of electric and electronic systems.

2. MEASUREMENT TEST SETUP

Fig. 1. General view of the investigated base station

For simulations of a direct lightning stroke to the

For possible equal distribution of the test current in

Fig. 2. Various means of connecting the surge generator

For currents measurements, Tektronix probes P6021

40 60 80 100 120 140 160

Fig. 7. Measured time domain current in the towers leg

Fig. 5. Surge current measurements in equipotential

Further, some currents in grounding conductors at the

3. MEASURED RESULTS FOR SCENARIO (1)

Fig. 8. Amplitudes of surge currents in one of the antenna

60 80 100 120 140 160 180

Fig. 9. Time domain current in equipotential bonding

60 80 100 120 140 160 180

base station of global systems for mobile communication

You might also like