Catalogs (4+1)

9
VIDEO -INTERCOM
TECHNICAL MANUAL 2002
1
2
3
4
5
6
INTRODUCTION
Notice to the installer and user
This edition contains helpful information on the operation and installation

of Farfisa articles.
Check the integrity of the device after removing it from the packing.
In order to make the systems work perfectly it is necessary to install only

Farfisa equipment, keeping strictly to the items referred to in each
diagram.
Read all the notes carefully, (even the small ones) in each installation
scheme and the working instructions of the system given in the
following pages.
For the sake of clarity, please notice that the sequence of the terminals
of each article has not been followed. Only the terminal code (letter and/
or number) is valid not the graphic sequence.
The items may have more terminals than the ones in the installation
diagrams. The excess terminals must not be utilized.
Packing materials (such as plastic bags, cardboard, polystyrene

foam, etc.) must be kept out of the reach of children.
Avoid bumping and hitting the apparatus, it could break of the CRT
tube with consequent projections of fragmented glass.
The manufacturer cannot be held responsible for possible damages
caused by improper, erroneous and unreasonable use.
For correct operation make sure that ventilation or heat dissipation
openings and slots are not obstructed.
Do not open or tamper with the video intercom apparatus when it is ON.
There is high voltage inside.
The cable runs of any intercom unit must be kept separate from the
mains as required by International standards.
In case of breakdown or change in the system consult specialized
personnel.
It is advisable to provide behind the (fused spur) power supply a
disconnecting and safety switch.
Before connecting the unit, make sure its data correspond's to those
of the mains.
General characteristics
- timed operation
- automatic extension of time during conversation
- automatic shut-OFF of system at the end of a conversation (by
replacing the hand-set)
- the possibility by every monitor to control one or more video entrances
- audio and video privacy between monitors
- switching ON of monitors one at a time
- the possibility to connect more monitors and intercoms in each flat
- the possibility to communicate privately among other monitors and
intercoms
- priority of video/audio connection on an outside call without the
possibility of switching on by other monitors at the same time
- power supply electronically protected against short circuits and
overloading.
European Mark of conformity to the

EEC Directives.
Mark of approval to German regulations.
CE MARK
The CE mark ensures that the product complies with the requirements of the
European Community Directives in force; in particular, Electrical Safety LVD73/23,
Electromagnetic Compatibility EMC89/336 and Telecommunication Terminals
R&TTE99/5 Directives.
As set forth by the Directives, the technical documentation and Conformity Declarations are available in the Companys offices for verifications and controls by
competent Authorities.
Quality assured firm.
TECHNICAL MANUAL
Edition 2002
VIDEO-INTERCOM SYSTEM
Page
INDEX
Project monitors series
PuntoVirgola monitors series
Intercoms
Mody push-button panels
ErreP/R push-button panels
Power supply and control unit
Service modules
Video memory
Installation instructions
Working instructions
Troubleshooting
2
8
11
12
21
23
24
25
26
28
29
Installation diagrams WITH COAXIAL CABLE
30
Mody Videokit
Si 5000M One-way videokit with application of multipolar cable art.1304
31
31
One or multi-way diagrams

Si 5050 Video-intercom system with audio-video privacy
Si 5051 Multi-way combined intercom video-intercom system with audio-video privacy
Si 5150 Video-intercom system with two automatically switched entrances, one of which is only audio
Si 5250 Video-intercom system with two automatically switched video entrances
Si 5256 Video-intercom system with two automatically switched entrances, one with surveillance camera
Si 5350 Video-intercom system with three automatically switched video entrances
Si 5550 Multi-way video-intercom system with auxiliary audio entrances and one main video entrance according to
the stairway
Si 5551 Multi-way video-intercom system with auxiliary video entrances and one main video entrance according to
the stairway
- Working diagrams
- Floor call
- One way additional diagrams
- Multi-way additional diagrams
32
33
35
37
39
41
43
45
4+1 video-intercom system WITHOUT COAXIAL CABLE
55
Mody push-button panels

Project monitors series
Power supply
Installation rules
55
58
59
60
60
Installation diagrams
Si 411R/1 One-way video-intercom system
Si 41MR/2 Multi-way combined intercom and video-intercom system
Si 42MR/1 Multi-way video-intercom system with two automatically switched entrances, one of which is only audio
Si 42MR/2 Multi-way video-intercom system with two automatically switched video entrances
61
61
62
63
64
Product list
65
48
49
50
54
WITHOUT COAX
*
WITH COAX
1
(9GB-2002)
47
MODY
MONITORS
Project series
ERREP/R
Wall-brackets for the PT5160, PT5160W and PT5160W-LCD monitors.

215.5
8 1/2"
89
WB5100. The wall bracket includes a

terminal board for connection to the
system, it is to be used when installing
2 - button monitors (control switch-ON
and door lock release), with a one call.
3 1/2"
PROJECT
215
8 7/16"
PUNTOVIRGOLA
*
SLIM
PT5160. Two-colour flat tube monitor with audiovideo privacy, electronic microphone, differentiated double electronic ringing sounds (modulated
and continuous note) and terminal board for the
connection to the wall-bracket. With two buttons,
one for control switch ON and one for door lock
release, and 6 supplementary buttons, that can be
added for additional services such as: control
switch ON, intercommunicating calls, stair lights,
door lock release, etc.
The buttons are included in the kit of the monitor.
The maximum acceptable current to the button
terminals is 60mA. For higher currents use relay
unit art.1471. It can be installed on the wall (with no
built-in) by using the wall-bracket WB5100 or
WB5160. For particular needs it is possible to
separate the common of the buttons labelled P4,
P5 and P6 by cutting the W1 jumper on the wallbracket. The buttons have the 2C terminal in
common. In this case the maximum acceptable
current to the three buttons is 0.5A.
Terminals
1 Video signal input 0.81.5Vpp
2 General ground
3 Video ground
4 Control switch ON - button
8 Positive power supply output for video
floor distributors 12Vdc
9 Door lock release - button
10 Call from the door station (180mA)
11 Audio ground
12 Microphone output
13 Speaker and automatic cancel
14 Positive power supply input 1824Vdc
V Not connected
83.5
3 5/16"
WITHOUT COAX
1824Vdc
0.35A
4" FLAT CRT
625 lines
15625Hz
50Hz
>5MHz
0.81.5Vpp
24 sec.
0+50C
90%RH
PT5160W-LCD. Version with colour LCD screen

monitor PT5160W.
V Activation input for digital systems

X1 AC power supply input 13Vac-0.35A
X2 Intercommunicating call input (ground command)
1C Common for P1, P2 and P3 buttons
P1P6 Service buttons - max 60mA
U
P
40.5
1 5/ "
122
4 13/16"
140 150 cm
4" 7" 4" 11"
Measures for the installation of the wall bracket

WB5100 or WB5160 to the wall, and recommended height from the floor.
aaaaaaaaaaaa
Supplementary push-buttons installation
Note: This version is applied to all video

installation diagrams with coaxial cable.
WITH COAX
Technical data
Power Supply
Operating current
Screen
Television standard
Horizontal frequency
Vertical frequency
Bandwidth
Video signal on 75
Starting up time
Operating temperature
Max. permissible humidity
Terminals
The terminals from 1 to 14 have the same functions and characteristics as the previous model.
43
1 11/16"
PT5160W. This model has the same features as

the previous one, but with a white finish.
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Bandwidth
Video signal on 75
Starting up time
WB5160. The wall bracket includes 2 terminal boards for connection to the system, it is
to be used when installing monitors with extra
buttons and/or 2 differentiated bells.
Located on the wall-bracket terminal board is
a J1 jumper positioned for the intercommunicating service (position A).
By using the PT5160, PT5160W and
PT5160W-LCD monitors with multi-way systems without the intercommunicating service,
the audio privacy can be restored by positioning the jumper J1 in B.
Taking out of button caps.
1824Vdc
0.4A
4" LCD
PAL
15625Hz
50Hz
>5MHz
0.81.5Vpp
1 sec.
0+50C
90%RH
2
(9GB-2002)
Inserting of extra buttons.
MODY
MONITORS
Project series
ERREP/R
U
P
PROJECT
*
Installation of the wall bracket WB5100 or

WB5160 to the wall, using a 83.5mm back
box and an expansion plug.
PUNTOVIRGOLA
U
P
Installation of monitor onto the wall bracket.
Dismounting of monitor from the wall bracket.
SLIM
Installation of the wall bracket WB5100

or WB5160 to the wall, by means of
expansion plugs.
Audio privacy or intercommunicating service
WB 5160
TA 5160
J2
U
P
X1 X2 2C 1C P1 P2 P3 P4 P5 P6
J3
1
3
1
2 4 8 9 10 11 12 13 14 V
W1
1 2 3
75
J1
1 2 3
J1
B
Plugging in of monitor connectors to the terminal
boards of wall bracket.
1 2 3
Position for the intercommunicating service.
Position for the audio privacy.
J1
WITHOUT COAX
TA5160. Table adapter for monitors PT5160,

PT5160W and PT5160W-LCD.
With 20 wire connection cable, junction box
and bracket with 2 terminals board.
Terminals
The terminals have the same numbers, functions
and characteristics as those of wall bracket
WB5160.
Mounting instruction
Make the connection of the cable to
the terminals of the table adapter.
Make the connection of the conductors of the system to the junction box.
Plug-in the 2 flat cable to the table
adapter.
Fasten the monitor to the table
adapter.
3
(9GB-2002)
WITH COAX
Installation of monitor to the table adapter.
Junction box.
MODY
MONITORS
Project series
ERREP/R
Wall-brackets for the PT5660W monitor.

212
8 1/2"
54
2 1/8"
113
4 7/16"

PROJECT
233
9 3/16"
PUNTOVIRGOLA
*
SLIM
PT5660W. White colour monitor with traditional cathode tube with audio-video privacy,
electronic microphone, differentiated double
electronic ringing sounds (modulated and
continuous note) and terminal board for the
connection to the wall-bracket. With two buttons, one for control switch ON and one for
door lock release, and 6 supplementary buttons, that can be added for additional services such as: control switch ON, intercommunicating calls, stair lights, door lock release,
etc. The buttons are included in the kit of the
monitor. The maximum acceptable current to
the button terminals is 60mA. For higher
currents use relay unit art.1471.
It can be installed on the wall by using the
wall-bracket art.WB5600 or WB5660 and the
back-box art. 1283. For particular needs it is
possible to separate the common of the buttons labelled P4, P5 and P6 by cutting the W1
jumper on the wall-bracket. The buttons have
the 2C terminal in common. In this case the
maximum acceptable current to the three
buttons is 0.5A.
WITHOUT COAX
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Bandwidth
Video signal on 75
Starting up time
Terminals
2 General ground
3 Video ground
11 Audio ground
V Not connected
By using the PT5660W monitors with multiway systems without the intercommunicating
service, the audio privacy can be restored by
positioning the jumper J1 in B.
Terminals
U
P
1824Vdc
0.6A
4.5" - 90
625 lines
15625Hz
50Hz
>5MHz
0.81.5Vpp
57 sec.
0+50C
90%RH
Installation of wall bracket WB5600 or WB5660 to the back box 1283.
J3
J2
*
U
P
WITH COAX
Plugging in of monitor connectors to the terminal boards of wall bracket.
4
(9GB-2002)
MODY
MONITORS
Project series
PROJECT
*
126
415/16"
PUNTOVIRGOLA
60
2 3/8 "
175
6 7/8 "
ERREP/R
1283. Back-box for monitors PT5660W and

PV1260.
Place the box on the wall at a height of about
1.5m (4' 11") from the floor keeping the front
edges flush-mounted and vertical to the finished plaster.
SLIM
140 150 cm
4 7"
4 11"
aaaaaaaaaaaaaaaaaaaa
Dismounting of monitor from the wall
bracket.
J3
X1
X2
2C
1C
P1
P2
P3
P4
P5
P6
2
4
8
9
10
11
12
13
14
V
J1
1 2 3
J1
B
J2
W1
1 2 3
J1
1 2 3
WITHOUT COAX
R1
75
5
(9GB-2002)
WITH COAX
WB 5660
MODY
MONITORS
Project series
ERREP/R
Wall-brackets for the PT5860 and PT5860W monitors.

212
8 1/2"
113
4 7/16"

PROJECT
233
9 3/16"
PUNTOVIRGOLA
*
SLIM
PT5860. Two-colour reflex monitor with audio-video privacy, electronic microphone, differentiated double electronic ringing sounds
(modulated and continuous note) and terminal board for the connection to the wallbracket. With two buttons, one for control
switch ON and one for door lock release, and
6 supplementary buttons, that can be added
for additional services such as: control switch
ON, intercommunicating calls, stair lights,
door lock release, etc. The buttons are included in the kit of the monitor. The maximum
acceptable current to the button terminals is
60mA. For higher currents use relay unit
art.1471.
It can be installed on the wall by using the
wall-bracket art.WB5600 or WB5660. For
particular needs it is possible to separate the
common of the buttons labeled P4, P5 and P6
by cutting the W1 jumper on the wall-bracket.
The buttons have the 2C terminal in common.
In this case the maximum acceptable current
to the three buttons is 0.5A.
Terminals
2 General ground
3 Video ground
11 Audio ground
V Not connected
Terminals
138
5 7/16"
92
3 5/8"
U
P
PT5860W. This model has the same features

as the previous one, but with a white finish.
WITHOUT COAX
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Bandwidth
Video signal on 75
Starting up time
By using the PT5860 and PT5860W monitors
with multi-way systems without the intercommunicating service, the audio privacy can be
restored by positioning the jumper J1 in B.
1824Vdc
0.6A
4.5" - 90
625 lines
15625Hz
50Hz
>5MHz
0.81.5Vpp
57 sec.
0+50C
90%RH
Measures for the installation of the wall bracket

WB5600 or WB5660 to the wall, and recommended
height from the floor.
140 150 cm
4" 7" 4" 11"
aaaaaaaaaaaaaaa
aaaaaaaaaaaaaaa
WITH COAX
U
P
Installation of the wall bracket WB5600 or WB5660 to the

wall, by means of expansion plugs.
6
(9GB-2002)
MODY
MONITORS
Project series
ERREP/R
J3
PROJECT
J2
PUNTOVIRGOLA
U
P
SLIM
Installation of monitor onto the wall

bracket.
Dismounting of monitor from the wall bracket.
J3
X1
X2
2C
1C
P1
P2
P3
P4
P5
P6
2
4
8
9
10
11
12
13
14
V
J1
1 2 3
J1
B
J2
W1
1 2 3
J1
1 2 3
WITHOUT COAX
R1
75
7
(9GB-2002)
WITH COAX
WB 5660
MODY
MONITORS
PuntoVirgola series
ERREP/R
Wall-brackets for the PV2160 and PV2160W monitors.

197
7 3/4 "
76
3"
PROJECT
228
9"
PUNTOVIRGOLA
*
SLIM
PV2160. Two-colour flat tube monitor with audio-video privacy, electronic microphone, differentiated double electronic ringing sounds
(modulated and continuous note) and terminal board for the connection to the wallbracket. With two buttons, one for control
switch ON and one for door lock release, and
5 supplementary buttons, that can be added
for additional services such as: control switch
ON, intercommunicating calls, stair lights,
door lock release, etc. The buttons are included in the kit of the monitor. The maximum
acceptable current to the button terminals is
60mA. For higher currents use relay unit
art.1471. It can be installed on the wall (with no
built-in) by using the wall-bracket WB2100 or
WB2160. For particular needs it is possible to
separate the common of the buttons labeled T4
and T5 by cutting the W1 jumper on the wallbracket. The buttons have the 2C terminal in
common. In this case the maximum acceptable
current to the three buttons is 0.5A.

terminal board for connection to the system, it is to be used when installing 2 button monitors (control switch-ON and
door lock release), with a one call.
Terminals
2 General ground
3 Video ground
11 Audio ground
V Not connected
83.5
3 5/16"
WITHOUT COAX
1824Vdc
0.35A
4" FLAT CRT
625 lines
15625Hz
50Hz
>5MHz
0.81.5Vpp
24 sec.
0+50C
90%RH
Terminals
1C Common for T1, T2 and T3 buttons
2C Common for T4 and T5 buttons
T1T5 Service buttons - max 60mA
P1
Not connected
43
1 11/16"
U
P
40.5
1 5/ "
PV2160W. This model has the same features

as the previous one, but with a white finish.
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Bandwidth
Video signal on 75
Starting up time
By using the PV2160 and PV2160W monitors
with multi-way systems without the intercommunicating service, the audio privacy can be
restored by positioning the jumper J1 in B.
122
4 13/16"
140 150 cm
4" 7" 4" 11"
Measures for the installation of the wall bracket WB2100

or WB2160 to the wall, and recommended height from the
floor.
aaaaaaaaaaaa
WITH COAX
Installation of the wall bracket WB2100 or WB2160 to the wall, by means of

expansion plugs.
8
(9GB-2002)
MODY
MONITORS
PuntoVirgola series
ERREP/R
*
PROJECT
U
P
PUNTOVIRGOLA
J2
J3
SLIM
1
3
V
14
13
12
11
10
9
8
4
2
R1
75
3
2
1
1 2 3
J1
J1
B
1 2 3
J1
WITHOUT COAX
T5
T4
T3
T2
T1
1C
2C
X2
X1
P1
WB2160
WITH COAX
9
(9GB-2002)
MODY
MONITORS
PuntoVirgola series
ERREP/R
Wall-brackets for the PV1260 monitor.

238
9 3/8 "
149
5 7/8 "
90
3 9/16"
PROJECT
140
205 5 1/2 "
1
8 /16"
For particular needs it is possible to

separate the common of the buttons
labelled P4, P5 and P6 by cutting the
W1 jumper located on the connecting
terminal board. These buttons have in
common the C2 terminal. In this case
the maximum acceptable current to
the buttons is 0.5A.
PUNTOVIRGOLA
*
SLIM
PV1260. Two-colour monitor with traditional

cathode tube with audio-video privacy, electronic microphone, differentiated double electronic ringing sounds (modulated and a continuous note) and terminal board for the connection to the wall-bracket. With 2 buttons,
one for control switch ON and the other for
door lock release and 6 supplementary service buttons that can be added for additional
services such as: control switch ON, intercommunicating calls, stair lights, door lock
release, etc. The buttons are included in the
kit of the monitor. The maximum acceptable
current to the buttons is 60mA. For higher
currents use the art.1471 relay unit. It can be
installed on the wall using the wall-bracket
WB1200 or WB1260 and the back-box
art.1283.
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Band width
Video signal on 75
Starting up time
1824Vdc
0.6A
4.5"-90
625 lines
15625Hz
50Hz
>5MHz
0.81.5Vpp
57 sec.
0+50C
90%RH
WB1200. The wall bracket includes a terminal

board for connection to the system, it is to be
used when installing 2 - button monitors (control
switch-ON and door lock release), with a one
call.
Terminals
2 General ground
3 Video ground
4 Control switch ON button
8 Positive power supply output for video floor
distributors 12Vdc
9 Door lock release button
11 Audio ground
14 Positive power supply input 1824Vdc-0.6A
V Not connected
By using the PV1260 monitor with multi-way
systems without the intercommunicating service, the audio privacy can be restored by
positioning the jumper J1 in B.
Terminals
Installation of wall bracket WB1200 or

WB1260 to the back box 1283.
WITHOUT COAX

WB1260
X1 X2 2C 1C P1 P2 P3 P4 P5 P6
1
3
1
WITH COAX
Plugging in of monitor connectors to the terminal boards of

wall bracket.
2 4 8 9 10 11 12 13 14 V
W1
75
J1
J1
B
1
10
(9GB-2002)
J1
PuntoVirgola series
Project series
INTERCOMS
MODY
MONITORS
86
3 3 /8"
3 1 /16"
214
214
8 1 /16"
8 1 /16"
PROJECT
175
6 7/8 "
77.5
1283. Back-box for PV1260 and PT5660W

monitors.
Place the box on the wall at a height of about
1.5m (4' 11") from the floor keeping the front
edges flush-mounted and vertical to the finished plaster.
72
2 13/16"
ERREP/R
72
2 13/16"
60
2 3/8 "
PT520N. Colour: beige.

PT520W. Colour: white.
PT538. Table adaptor complete with ballast

base, connector, 13 wires cable. For all
Project intercoms.
Connection of the electronic bell SR40 inside

an intercom, Project series, to make intercommunicating calls.
Terminals
1 microphone
2 loudspeaker
3 ground
5 door release push-button (max 1A)
6 buzzer (absorption 0.2A)
9 electronic bell input
SLIM
PT 510N. Colour: beige.

PT 510W. Colour: white.
140 150 cm
4 7"
4 11"
Terminals
1 microphone
2 loudspeaker
3 ground
5 door lock release button (max 1A)
6 buzzer (absorption 0.2A)
7 common push-buttons (
and 1)
9 electronic bell input
P1 service push-button (max 1A)
P2P9 service push-buttons (max 0.5A)
PT 510. Two-colour intercom complete with

push-button, spiral cord, buzzer and electronic
microphone. Wall-mounted with screws or fixed
to back box.
PUNTOVIRGOLA
126
415/16"
PT520. Two-colour intercom complete with

buzzer, spiral cord, electronic microphone
and 2 buttons that can be increased up to 10
by adding the single button unit art.PT501.
It can be installed on the wall with expansion
plugs or on a wall box.
Connection of the private conversation module

SM50 inside an intercom Project series.
W1
W1
1
13Vca
X1
C
B
Note: In the intercoms it is necessary to cut

the jumper W1 which links terminals 3 and 7.
R1
11
(9GB-2002)
SM 50
N.B.: In the intercoms it is necessary to cut the
jumper W1 which links terminals 3 and 7; in the
SM50 module to cut the resistance R1.
1
3
1
4
8
9
10
11
12
13
14
2
CT
CT
5
6
3
1
2
5
6
3
1
2
75
VC
WITH COAX
These systems are not intercommunicating,

therefore all the models conceived for systems 4+1 can be used.
Connection of 1 or max. 3 intercoms

parallel to the monitor.
2 1
10K
SR 40
X2
WITHOUT COAX
13Vac
MODY
PUSH-BUTTON PANELS
MODY series
ERREP/R
Module frames complete with back box
124
Push-button panel in aluminium composed of

modular elements, able to resolve all installation
requirements. Back boxes, module frames, electric door speaker, camera, rain shelter and various
button modules are the basic elements in this
push-button panel line.
64
4 7 / 8"
1
2 / 2"
395
9
15 / 16 "
PROJECT
304.5
12 "
213
8 3 / 8"
PUNTOVIRGOLA
121.5
4 13 / 16"
MD 71
MD 72
Hood covers
MD 73
19
MD 74
/4"
151
276
5 15 /16"
SLIM
414.5
323
10 7 / 8"
16 5 /16"
12 11 /16"
231.5
9 1 / 8"
140
5 1 / 2"
MD 81
MD 82
MD 83
MD 804
MD 84
MD 86
Rain shelter with module frames
401
15 13 /16"
151
5 15 /16"
414.5
MD 808
414.5
40
1 9 /16"
16 5 /16"
16 5 /16"
323
323
12 11 /16"
12 11 /16"
231.5
9 1 / 8"
WITHOUT COAX
140
5 1 / 2"
MD 89
MD 91
MD 92
MD 93
MD 812
25
1"
MD 904
276
401
10 7 / 8"
15 13 /16"
80
3 1 / 8"
414.5 16 5 / 16"
323 12 11 / 16"
231.5
WITH COAX
1
9 /8 "
MD 94
MD 96
MD 908
MD 99
12
(9GB-2002)
MD 912
65
2 9 /16"
MODY
PUSH-BUTTON PANELS
MODY series
Modules for electric door speaker (amplifier)
25.5
91
3 9 /16"
1"
ERREP/R
ELECTRIC DOOR-SPEAKER
(amplifier)
1 row push-button modules
MD 10
MD 11
MD 12
Without call buttons
1 call button
2 call buttons
MD 22
MD 23
MD 24
1 call button
2 call buttons
3 call buttons
4 call buttons
Transmitter adjustable
volume
MD 21
PUNTOVIRGOLA
Button modules
MD 30.
It consists of a double amplifier (receiver and
transmitter) with adjustable volume of 2 channels. Also fittable to ErreP/R and Prestige
push-button panels (for the ErreP/R door stations by means of 299/1 adaptor).
PROJECT
55
2 3 /16"
SLIM
2 row push-button modules

Receiver adjustable volume
Modules for electric door speaker (amplifier)
Terminals
1 receiver
2 transmitter
3 positive power supply 68Vdc - 60mA
4 ground
MD 122
MD 124
2 call buttons
4 call buttons
Dismounting and protection of name

labels
Button modules
MD 222
2 call buttons
MD 224
MD 226
MD 228
4 call buttons
6 call buttons
8 call buttons
50
MD 20
Blank module
FC 52P
Number module
Keypad module for

access control
(see page 20)
MD41 B/W CCD camera

MD41C Colour CCD
camera (see page 20)
MD 50
Dismounting of name holder to insert name

label.
WITHOUT COAX
Modules: blank, number , access control and cameras
13
(9GB-2002)
WITH COAX
In any button module, to avoid the dismounting of name holder a screw 3MAx12 can be
inserted in the holes in order to block each
label.
MODY
PUSH-BUTTON PANELS
MODY series
ERREP/R
*
PROJECT
*
PUNTOVIRGOLA
5 5"
aaaaaaaaaa
Openings for cables.
SLIM
Place the box of the camera unit at a height of

about 1.65m (5' 5") from the floor keeping the
front edges flush-mounted and vertical to the
finished plaster.
Position the camera unit in such a way that
solar rays or other direct light or intense
reflections do not hit the camera lens.
Mounting of button module.
Flush mounting and cables placing.
WITHOUT COAX
V
M
F
H
Insertion of cable bush between back boxes.

The cable bushes must be inserted before
brickwork.
(a)
WITH COAX
Lower fixing of the module frame.
14
(9GB-2002)
Lower fixing of the module frame on back box.

It is advised to insert a protection (a) between
panel and wall while fixing.
MODY
PUSH-BUTTON PANELS
MODY series
ERREP/R
*
PROJECT
*
PUNTOVIRGOLA
Alignment of the panel.
Hood covers
SLIM
V
M
F
H
Mounting of frame bottom and door speaker

(amplifier).
Modules insertion and wall fixing of rain shelter.
Fixing of the hood cover between the back

box and the module frame.
WITHOUT COAX
Rain shelter
Dismounting of the frame top side from the

rain shelter.
15
(9GB-2002)
Mounting of the frame top to the rain shelter.
WITH COAX
Top fixing of the panel.
MODY
PUSH-BUTTON PANELS
1 row push-button
MODY series
Example of Mody push-button panel installations.
ERREP/R
*
PROJECT
1 call button
2 call buttons
3 call buttons
4 call buttons
5 call buttons
6 call buttons
7 call buttons
8 call buttons 10 call buttons
PUNTOVIRGOLA
50
7 call buttons
8 call buttons
9 call buttons
10 call buttons
50
50
12 call buttons
14 call buttons
23 call buttons
24 call buttons
26 call buttons
11 call buttons
SLIM
50
16 call buttons
18 call buttons
19 call buttons
50
21 call buttons
50
27 call buttons
50
WITHOUT COAX
28 call buttons
30 call buttons
32 call buttons
34 call buttons
37 call buttons
38 call buttons
40 call buttons
42 call buttons
50
35 call buttons
50
WITH COAX
43 call buttons
48 call buttons
52 call buttons
16
(9GB-2002)
58 call buttons
1 row push-button
Compositions and
dimensions
1 MD30
1 MD11
1 MD41
1 MD30
1 MD12
1 MD41
1 MD30
1 MD10
1 MD23
1 MD41
1 MD30
1 MD10
1 MD41
1 MD30
1 MD41
1 MD30
1 MD41
8
9
124x213x19
(47/8" x 8 3/8" x 3/4")
5
6
124x304,5x19
(47/8" x 12" x 3/4")
248x213x19
(9 /4" x 8 3/8" x 3/4")
10
Back box and

module frame
Hood
covers
Rain
shelter
1 MD72
1 MD82
1 MD92
1 MD72
1 MD82
1 MD92
1 MD73
1 MD83
1 MD93
1 MD24
1 MD73
1 MD83
1 MD93
1 MD11
1 MD24
1 MD73
1 MD83
1 MD93
1 MD12
1 MD24
1 MD73
1 MD83
1 MD93
1 MD30
1 MD10
1 MD24
1 MD23
2 MD72
1 MD84
1 MD94
1 MD41
1 MD30
1 MD10
2 MD24
2 MD72
1 MD84
1 MD94
1 MD41
1 MD30
1 MD11
2 MD24
2 MD72
1 MD84
1 MD94
1 MD12
2 MD24
2 MD72
1 MD84
1 MD94
1 MD30
1 MD10
2 MD24
1 MD23
2 MD73
1 MD86
1 MD96
12
1 MD41
1 MD30
1 MD10
3 MD24
2 MD73
1 MD86
1 MD96
13
1 MD41
1 MD30
1 MD11
3 MD24
2 MD73
1 MD86
1 MD96
14
1 MD41
1 MD30
1 MD12
3 MD24
2 MD73
1 MD86
1 MD96
15
1 MD41
1 MD30
1 MD10
3 MD24
1 MD23
2 MD73
1 MD86
1 MD96
16
1 MD41
1 MD30
1 MD10
4 MD24
2 MD73
1 MD86
1 MD96
17
1 MD41
1 MD30
1 MD11
4 MD24
2 MD73
1 MD86
1 MD96
18
248x304.5x19
(9 3/4" x 12" x 3/4")
1 MD41
1 MD30
1 MD12
4 MD24
2 MD73
1 MD86
1 MD96
19
1 MD41
1 MD30
1 MD10
4 MD24
1 MD23
2 MD74
1 MD808
1 MD908
20
1 MD41
1 MD30
1 MD10
5 MD24
2 MD74
1 MD808
1 MD908
21
1 MD41
1 MD30
1 MD11
5 MD24
2 MD74
1 MD808
1 MD908
22
1 MD41
1 MD30
1 MD12
5 MD24
2 MD74
1 MD808
1 MD908
23
1 MD41
1 MD30
1 MD12
5 MD24
1 MD21
2 MD74
1 MD808
1 MD908
24
1 MD41
1 MD30
1 MD12
5 MD24
1 MD22
2 MD74
1 MD808
1 MD908
1 MD41
1 MD30
1 MD12
5 MD24
1 MD23
2 MD74
1 MD808
1 MD908
25
26
248x395x19
(9 3/4" x 15 9/16" x 3/4")
1 MD30
1 MD12
6 MD24
2 MD74
1 MD808
1 MD908
27
1 MD41
1 MD30
1 MD11
5 MD24
2 MD23
3 MD73
1 MD89
1 MD99
28
1 MD41
1 MD30
1 MD10
7 MD24
3 MD73
1 MD89
1 MD99
1 MD41
1 MD30
1 MD11
7 MD24
3 MD73
1 MD89
1 MD99
30
1 MD41
1 MD30
1 MD12
7 MD24
3 MD73
1 MD89
1 MD99
31
1 MD41
1 MD30
1 MD11
6 MD24
2 MD23
3 MD74
1 MD812
1 MD912
32
1 MD41
1 MD30
1 MD12
6 MD24
2 MD23
3 MD74
1 MD812
1 MD912
33
1 MD41
1 MD30
1 MD11
8 MD24
3 MD74
1 MD812
1 MD912
34
1 MD41
1 MD30
1 MD12
8 MD24
3 MD74
1 MD812
1 MD912
35
1 MD41
1 MD30
1 MD12
8 MD24
1 MD21
3 MD74
1 MD812
1 MD912
36
1 MD41
1 MD30
1 MD12
8 MD24
2 MD21
3 MD74
1 MD812
1 MD912
37
1 MD41
1 MD30
1 MD11
8 MD24
2 MD22
3 MD74
1 MD812
1 MD912
38
1 MD41
1 MD30
1 MD12
8 MD24
2 MD22
3 MD74
1 MD812
1 MD912
29
39
372x304.5x19
(14 5/8" x 12" x 3/4")
372x395x19
(14 /8" x 15 9/16" x 3/4")
1 MD11
8 MD24
2 MD23
3 MD74
1 MD812
1 MD912
1 MD30
1 MD12
8 MD24
2 MD23
3 MD74
1 MD812
1 MD912
41
1 MD41
1 MD30
1 MD12
9 MD24
1 MD23
3 MD74
1 MD812
1 MD912
42
1 MD41
1 MD30
1 MD12
10 MD24
3 MD74
1 MD812
1 MD912
43
1 MD41
1 MD30
1 MD12
8 MD24
3 MD23
4 MD74
45
1 MD41
1 MD30
1 MD11
11 MD24
4 MD74
47
1 MD41
1 MD30
1 MD10
11 MD24
3 MD21
4 MD74
48
1 MD41
1 MD30
1 MD11
11 MD24
3 MD21
4 MD74
50
1 MD41
1 MD30
1 MD10
11 MD24
3 MD22
4 MD74
1 MD41
1 MD30
1 MD12
11 MD24
3 MD22
4 MD74
1 MD41
1 MD30
1 MD10
11 MD24
3 MD23
4 MD74
1 MD41
1 MD30
1 MD12
11 MD24
3 MD23
4 MD74
1 MD41
1 MD30
1 MD12
14 MD24
4 MD74
52
53
55
58
496x395x19
(19 1/2" x 15 9/16" x 3/4")
or MD74 or MD804 or MD904
* or MD20 or MD50 or FC52P
17
(9GB-2002)
Optional
It replaces
MD72, 73, 74
WITH COAX
1 MD30
1 MD41
1 MD41
40
WITHOUT COAX
1 MD41
SLIM
1 MD30
1 MD41
1 MD41
11
PUNTOVIRGOLA
1 MD41
Button and info or

blank modules
Module for
speaker
PROJECT
Door speaker
(amplifier)
Camera
module
ERREP/R
N
calls
Composition board of Mody push-button panels.
MODY series
MODY
PUSH-BUTTON PANELS
MODY
PUSH-BUTTON PANELS
2 row push-button
MODY series
ERREP/R
*
PROJECT
6 call buttons
8 call buttons
10 call buttons
12 call buttons
14 call buttons 16 call buttons 20 call buttons
PUNTOVIRGOLA
50
14 call buttons
16 call buttons
18 call buttons
20 call buttons
24 call buttons
28 call buttons
46 call buttons
48 call buttons
52 call buttons
22 call buttons
SLIM
50
32 call buttons
36 call buttons
38 call buttons
50
42 call buttons
50
54 call buttons
50
WITHOUT COAX
56 call buttons
60 call buttons
64 call buttons
68 call buttons
74 call buttons
76 call buttons
80 call buttons
84 call buttons
50
70 call buttons
50
WITH COAX
86 call buttons
96 call buttons
104 call buttons
18
(9GB-2002)
116 call buttons
MODY
*
1 MD122
1 MD72
1 MD82
1 MD92
1 MD30
1 MD124
1 MD72
1 MD82
1 MD92
1 MD41
1 MD30
1 MD10
1 MD226
1 MD73
1 MD83
1 MD93
1 MD41
1 MD30
1 MD10
1 MD228
1 MD73
1 MD83
1 MD93
1 MD41
1 MD30
1 MD122
1 MD228
1 MD73
1 MD83
1 MD93
1 MD41
1 MD30
1 MD124
1 MD228
1 MD73
1 MD83
1 MD93
14
1 MD41
1 MD30
1 MD10
1 MD228
2 MD72
1 MD84
1 MD94
16
1 MD41
1 MD30
1 MD10
2 MD228
2 MD72
1 MD84
1 MD94
18
1 MD41
1 MD30
1 MD122
2 MD228
2 MD72
1 MD84
1 MD94
20
1 MD41
1 MD30
1 MD124
2 MD228
2 MD72
1 MD84
1 MD94
22
1 MD41
1 MD30
1 MD10
2 MD228
2 MD73
1 MD86
1 MD96
24
1 MD41
1 MD30
1 MD10
3 MD228
2 MD73
1 MD86
1 MD96
26
1 MD41
1 MD30
1 MD122
3 MD228
2 MD73
1 MD86
1 MD96
28
1 MD41
1 MD30
1 MD124
3 MD228
2 MD73
1 MD86
1 MD96
30
1 MD41
1 MD30
1 MD10
3 MD228
2 MD73
1 MD86
1 MD96
32
1 MD41
1 MD30
1 MD10
4 MD228
2 MD73
1 MD86
1 MD96
34
1 MD41
1 MD30
1 MD122
4 MD228
2 MD73
1 MD86
1 MD96
10
12
1 MD30
1 MD124
4 MD228
2 MD73
1 MD86
1 MD96
1 MD41
1 MD30
1 MD10
4 MD228
2 MD74
1 MD808
1 MD908
40
1 MD41
1 MD30
1 MD10
5 MD228
2 MD74
1 MD808
1 MD908
42
1 MD41
1 MD30
1 MD122
5 MD228
2 MD74
1 MD808
1 MD908
44
1 MD41
1 MD30
1 MD124
5 MD228
2 MD74
1 MD808
1 MD908
46
1 MD41
1 MD30
1 MD124
5 MD228
2 MD74
1 MD808
1 MD908
48
1 MD41
1 MD30
1 MD124
5 MD228
2 MD74
1 MD808
1 MD908
1 MD41
1 MD30
1 MD124
5 MD228
2 MD74
1 MD808
1 MD908
50
52
248x395x19
(9 3/4" x 15 9/16" x 3/4")
6 MD228
2 MD74
1 MD808
1 MD908
1 MD122
5 MD228
3 MD73
1 MD89
1 MD99
56
1 MD41
1 MD30
1 MD124
7 MD228
3 MD73
1 MD89
1 MD99
58
1 MD41
1 MD30
1 MD122
7 MD228
3 MD73
1 MD89
1 MD99
60
1 MD41
1 MD30
1 MD124
7 MD228
3 MD73
1 MD89
1 MD99
62
1 MD41
1 MD30
1 MD122
6 MD228
3 MD74
1 MD812
1 MD912
64
1 MD41
1 MD30
1 MD124
6 MD228
3 MD74
1 MD812
1 MD912
66
1 MD41
1 MD30
1 MD122
8 MD228
3 MD74
1 MD812
1 MD912
68
1 MD41
1 MD30
1 MD124
8 MD228
3 MD74
1 MD812
1 MD912
70
1 MD41
1 MD30
1 MD124
8 MD228
3 MD74
1 MD812
1 MD912
72
1 MD41
1 MD30
1 MD124
8 MD228
3 MD74
1 MD812
1 MD912
74
1 MD41
1 MD30
1 MD122
8 MD228
3 MD74
1 MD812
1 MD912
76
1 MD41
1 MD30
1 MD124
8 MD228
3 MD74
1 MD812
1 MD912
78
1 MD41
1 MD30
1 MD122
8 MD228
3 MD74
1 MD812
1 MD912
80
1 MD41
1 MD30
1 MD124
8 MD228
3 MD74
1 MD812
1 MD912
82
1 MD41
1 MD30
1 MD124
9 MD228
3 MD74
1 MD812
1 MD912
84
1 MD41
1 MD30
1 MD124
10 MD228
3 MD74
1 MD812
1 MD912
86
1 MD41
1 MD30
1 MD124
8 MD228
4 MD74
90
1 MD41
1 MD30
1 MD122
11 MD228
4 MD74
94
1 MD41
1 MD30
1 MD10
11 MD228
4 MD74
96
1 MD41
1 MD30
1 MD122
11 MD228
4 MD74
100
1 MD41
1 MD30
1 MD10
11 MD228
4 MD74
104
1 MD41
1 MD30
1 MD124
11 MD228
4 MD74
106
1 MD41
1 MD30
1 MD10
11 MD228
4 MD74
110
1 MD41
1 MD30
1 MD124
11 MD228
4 MD74
116
1 MD41
1 MD30
1 MD124
14 MD228
4 MD74
19
(9GB-2002)
WITH COAX
1 MD124
1 MD30
1 MD30
1 MD41
WITHOUT COAX
1 MD41
54
SLIM
1 MD41
38
248x304.5x19
(9 3/4" x 12" x 3/4")
PUNTOVIRGOLA
36
124x304,5x19
(47/8" x 12" x 3/4")
PROJECT
1 MD30
1 MD41
124x213x19
(47/8" x 8 3/8" x 3/4")
1 MD41
ERREP/R
MODY
PUSH-BUTTON PANELS
MODY series
ERREP/R
CAMERAS
ACCESS CONTROL KEYPAD

124
52
124
2 1 /16"
4 7 /8"
AMPLIFIED DOOR STATIONS

124
52
PROJECT
90
90
90
3 9 /16"
3 /16"
9
3 9 /16"
PUNTOVIRGOLA
19
3
/4"
MD 41.
This module includes:
- solid-state camera (CCD) with auto iris, 3.6mm
fixed optics and 6 infrared-ray LEDs.
- front plate in anodized aluminium, with breakproof transparent screen.
- horizontal and vertical sweep.
MD 41C Color.
Colour version of model MD41.
SLIM
Terminals
V video signal output
M ground
F not connected
H positive power supply
input 21Vdc
V
M
F
H
Sweeps
If necessary, you can manually change the camera
framing by unloosening and adjusting the horizontal or
vertical screw in the desired direction (or both screws if
you want to adjust the image in all directions).
horizontal
45
1 3 /4 "
4 7 /8"
2 1 /16"
4 7 /8"
19
19
3
/4"
FC52P.
Access control keypad with 12 digits and 2
relays for lock release. 4 programmable
access codes for each relay. Programmable door opening time from 1 up 99 sec. for
each relay (or bistable operation of one
relay). Acoustic confirmation for entered
keys, accepted programming and for wrong
codes.
Power supply: 13VAC/DC-0.1A.
Technical data
Power supply:
12Vac/dc 10%
Stand-by current:
0.015A
Maximum current consumption: 0.1A
Contact ratings:
12VAC-5A
Numbers of codes for relays 1: 4
Numbers of codes for relays 2: 4 or direct
activation
Activation time for each relay: from 1 to 99 sec.
(or bistable relay 1)
Operating temperature:
0 +40C
Maximum permissible humidity:
85% RH
Terminals
1 normally closed contact of relays 2
2 normally open contact of relays 2
3 common contact of relays 2
4 normally closed contact of relays 1
5 normally open contact of relays 1
6 common contact of relays 1
7 ground or alternate voltage input
8 positive or alternate voltage input
/4"
MD 100. 1 button module.

It can be applied to all systems 4+1, intercommunicating systems, and video-intercom systems with coaxial cable.
It includes electric door speaker, amplified
in the two channels, volume control of receiver, call button and front plate in anodized aluminium. It can replace in many
installations module MD11 and MD30, using all the other accessories of the Mody
series.
For module installation, see the diagram on
page 32.
MD 200. 2 buttons module.
Terminals
ground
supply 13Vac-0.13A
1
receiver
2
transmitter
C
call buttons common
call buttons
nameplate lamp (24V-70mA)
1
12
WITHOUT COAX
vertical
12Vca
12V
13Vac
Relay
Rel1 1
12Vcc
Relay
Rel2 2
WITH COAX
Technical data
MD41
MD41C
Power supply
Operating current
Output video signal
Standard segnale video
Minimum illumination
White balance
Sensor
Pixel number
Vertical frequency
Lens
Adjustable focus
Auto-iris
Horizontal sweep
Vertical sweep
Maximum permissible humidity
213Vdc
0.2A
1Vpp on 75
CCIR
2 Lux
CCD 1/4" B/W
291000
15625Hz
50Hz
3.6mm; F5
0.1m
electronic
15
15
-10+40C
80%RH
213Vdc
0.4A
1Vpp on 75
PAL
2.5 Lux
auto
CCD 1/3" colour
291000
15625Hz
50Hz
4mm; F4
0.6m
electronic
15
15
-10+40C
80%RH
20
(9GB-2002)
Note
The specifications of
MD40 and MD40C cameras are the same as
MD41 and MD41C models, except for pan&tilt,
which is not available.
1
2
3
4
5
6
Lamp terminals
Button terminal board
Call buttons common
Stair light button terminals
External volume adjustment
Terminal board for audio/powering
MODY
PUSH-BUTTON PANELS
112
50
ErreP/R series
ELECTRIC DOOR SPEAKER

(amplifier)

40
4 7/16"
1 15/16"
1 9 /16"
ERREP/R
CAMERA UNIT
ErreP/R - TM - NP/N series
ErreP/R series
122
4 13 /16"
164
6 1/8 "
6 7 /16"
PROJECT
1 2 3 4
155.5
1
2
3
4
Receiver
Transmitter
Power supply 68Vdc -60mA
Ground
SLIM
Technical data
Power supply
Operating current
Video signal on 75
Pixel number
Vertical frequency
Lens
Adjustable focus
Opening of auto-iris
Terminals
RP100. 1-button amplified door station.

It can be used in all one-way video-intercom
systems where the camera unit is separated
from the audio door station or where 1 or more
audio door stations are needed. It is complete
with an amplifier, in both channels, electric
door speaker, volume control, anodized aluminium call button and front panel, rain shelter and name plate light.
It can be installed on the wall with expansion
plugs or on a wall box.
- solid state camera (CCD) with auto iris,

3.6mm lens, infrared LEDs, electronic climatization and anti-clouding circuits
- anodized aluminium front plate complete with
transparent theft-proof screen
- back-box
- aluminium rain shelter
- key and safety screws for fixing the plate
337C. It features a double amplifier (receiver

and transmitter); receiver has volume control. It is applicable inside the RP, NP or TM
push-button panels (or in other push-button
panels by means of the adaptor art.299).
Provided with an electret microphone and
tropicalized speaker.
PUNTOVIRGOLA
1385R.
The camera unit is used in the multi-way
video systems composed of:
RP 200. 2-button amplified door station.

213Vdc
0.26A
1Vpp
2 lux
291000
15625Hz
50/60Hz
3.6mm; F5
0.1m
-10+40C
90%RH
M V F A H
Terminals
M Video ground (shield of coaxial cable)
V Video output signal 1Vpp (coaxial cable)
F General ground
A Alternate voltage input for name plate lights
and climatizing circuit 13Vac-40mA
H Positive power supply input for camera and
infrared LEDs 213Vdc-260mA
Technical data
Power supply:
13Vac
Operating current: 130mA
Terminals
1 Receiver
2 Transmitter
C Common call buttons
P1 Call button
P2 Call button
- Ground
Alternate voltage input 13Vac
376 14 13 /16"
8 5 /8 "
RP12
RP10
RP8
RP4
RP6
RP2
RP
The unit should be flush-mounted and the

microphone should be firmly attached to
the front panel to avoid feedback and to
obtain the highest audio quality.
313 12 5 /16"
282 11 1 /16"
250 9 13 /16"
219
RP. Push-button panels with anodized aluminium front panel and buttons, complete
with name plate lights and height adjustable
contacts to compensate imperfections of the
wall. The electric door speaker can be fitted
inside the push-button panel.
WITHOUT COAX
313 12 5 /16"
282 11 1 /16"
250 9 13 /16"
219
8 5 /8 "
R12
R10
R8
21
(9GB-2002)
WITH COAX
R14
R. Push-button panels provided

only with buttons. An electric door
speaker cannot be fitted inside. When
such panels are installed together
with the previous ones, a system with
over 12 calls is obtained (see table on
page 22).
*
*
ErrreP/R series
ERREP/R
MODY
PUSH-BUTTON PANELS
Installation notes
Among the back-box of the camera unit and
the push-button panel apply, before mounting
on to the wall, the tips and fair leads provided
in the kit.
Place the box of the camera unit at a height

of about 1.5m (4' 11") from the floor keeping
the front edges flush-mounted and vertical to
the finished plaster.
Position the camera unit in such a way that

solar rays or other direct light or intense
reflections do not hit the camera lens.
PROJECT
Example of assembly of the back-box with an even number of ErreP/R series

push-button panels
Template spacers and short
cable holder bushings.
ALTO
UP
PUNTOVIRGOLA
Template spacers and long

cable holder bushings.
1385R
1
6 /4 "
Example of assembly of back-box with an uneven

number of ErreP/R push-button panel series
ALTO
UP
1385R
1
6 /4 "
5 13/16"
1385R
1385R
RP..
RP..
R..
RP..
R..
RP..
SLIM
4 11 "
9
1 /16"
40mm 1 9 /16"
aaaaaaa
9
1 /16"
Instructions of the various ErreP/R push-button panel series and their dimensions en mm (and inches)
L and H = Dimensions of the panel
l and h = Dimensions of the back-box
WITHOUT COAX
Series
L
H
RP
112 (4 7/16")
R+RP
R+RP+R
R+RP+R+R
R+R+RP+R+R
224 (8 13/16")
336 (13 1/4")
448 (17 5/8")
560 (22 1/16")
L
h
R8
RP1
R8+RP1=9
2R8+RP1=17
3R8+RP1=25
4R8+RP1=33
R8
RP2
R8+RP2=10
2R8+RP2=18
3R8+RP2=26
4R8+RP2=34
250
(9 13/16")
R10
RP4
R10+RP4=14
2R10+RP4=24
3R10+RP4=34
4R10+RP4=44
238
(9 3/8")
281.5
(11 1/16")
R12
RP6
R12+RP6=18
2R12+RP6=30
3R12+RP6=42
4R12+RP6=54
269.5
(10 5/8")
313
(12 5/16")
R14
RP8
R14+RP8=22
2R14+RP8=36
3R14+RP8=50
4R14+RP8=64
301
(11 7/8")
215 (8 7/16")
327 (12 7/8")
439 (17 5/16")
551 (21 11/16")
218.5
(8 5/8")
WITH COAX
103 (4 1/16")
22
(9GB-2002)
206.5
(8 1/8")
MODY
POWER SUPPLY AND CONTROL UNIT
89
3 1 /2"
1382. AUDIO-VIDEO TIMER.
PRS210. TRANSFORMER.
Connected to the stabilized power supply

art.1281, it allows a video-intercom system to
be timed (50 seconds).
It also allows time to be increased during a
conversation (3 minutes), automatic power
OFF at the end of the conversation; switching
ON of one monitor at a time. By adding the
intercommunicating module art.1443E on the
proper connector, an intercommunicating
operation with privacy towards the external
speaker is obtained.
It is used to power the amplified external units

MD100, MD200, RP100, RP200 and UP series, additional door locks, name plate lights,
etc.
Technical data
Turn ON time: -50 sec. with handset replaced
-3 min. with handset lifted
0+50C
Maximum permissible humidity 90%RH
Housing
DIN 6 modules A
Terminals
I Logic command output of timing 0/5Vdc
+ Positive voltage input 1828Vdc-2A
- Ground
A Alternating voltage input-output 13Vac-1.6A
D Alternating voltage output for the common of
push-button 13Vac-0.5A (intermittent service)
H Timed positive voltage output for the camera
unit 1828Vdc-0.5A max.
F Ground
1 Transmitter audio channel input 4.5Vdc-10mA
2 Receiver audio channel input 2Vdc-16mA
3 Positive voltage output 8Vdc-0.1A
S Electronic door lock release 1A
4 Control switching ON input from the monitors
5.5Vdc-90mA
9 Door lock release command 50mA
11 Audio ground
12 Transmitter audio channel output 4.5Vdc10mA
13 Receiver audio channel output 2Vdc-16mA
14 Timed positive voltage output for the monitors
1828Vdc-1.5A max.
Technical data
Input voltage: 127V or 230Vac
Power: 15VA
Output voltage: 13Vac
Maximum current with direct use: 0.7A
Maximum current with intermittent: 1A
Housing: DIN 3 modules A
Weight: 0.42Kg
Approved: VDE
Operating temperature: 0 +50C
Maximum permissible humidity: 90% RH
1443E. Intercommunicating module.

Added inside the timer art.1382, it allows for
the intercommunicating function with privacy
towards the external speaker.
1443E
1443E
WITHOUT COAX
Note
- The power supply is not provided with fuses,
but all of its outputs are protected against
overloading and short circuiting by temperature sensors. To reset the power supply, power must be cut off for about one minute and
can be restored after having eliminated the
defect.
- The power supply must be installed in a dry
place and can be fixed on DIN bar or on a wall
by using the expansion plugs.
- The connection between power supply 1281
and timer 1382 is not to be longer than 25cm.
54
2 1 /8"
SLIM
Terminals
A Output voltage 13Vac for:
-name plate light, exchangers and climatized
camera (continuous service 0.6A)
-electric door lock and bells (intermittent service 1A)
- Ground
+ Continuous output 21Vdc-1A (timed operation)
I Logic command input from timing
0 = activated
+5Vdc = non activated
3 /2"
1
Technical data
Input voltage
127 or 230Vac
Frequency
50/60Hz
Power
48VA
0+50C
Housing
DIN 8 modules A
Weight
0.95Kg.
89
PUNTOVIRGOLA
1281. STABILIZED POWER SUPPLY WITH

SWITCHING REGULATOR.
Connected to the timer art.1382, allows to
drive at low voltage a monitor (or 2 in parallel
in FLAT type), a camera unit with a solid state
sensor (CCD), electric door lock, name plate
lights, etc.
4 1 /4"
89
3 1/2 "
PROJECT
107.5
2 9 /16"
140
5 1/2 "
65
2 9 /16"
ERREP/R
65
74
2 15/16"
1282E
1382
WITH COAX
23
(9GB-2002)
MODY
SERVICE MODULES
ERREP/R
*
74
2 15/16"
PROJECT
140
5 1/2 "
PUNTOVIRGOLA
*
SLIM
It is used in systems with 2 or more video

entrances for switching automatically the
video signals, the audio lines and door lock
on the calling entrance. Can be fixed on DIN
bar or with two expansion plugs. In housing
DIN 8 modules A. For the switching of video
signals it is advisable to use terminals 8-8a8b and 9-9a-9b, being that they are physically
closer.
Terminals
1 Power supply 13Vac-0.1A
2 Ground
3 and 4 Driver to switch the relay in b position
- ON position
5 and 6 Driver to switch the relay in a position
- OFF position
7, 8, 9, 10, 11, 12 and 13 Common relay contacts
7a, 8a, 9a, 10a, 11a, 12a and 13a OFF position
of the relay contacts
7b, 8b, 9b, 10b, 11b, 12b and 13b ON position
of the relay contacts
1
2
3
4
5
7b
ON (b)
2 /16"
7a
8b
8a
9b
9a
54
89
2 3 /4"
1273TV. EXCHANGER.
2 9 /16"
70
89
3 1/2 "
65
65
2 1 /8"
3 1 /2"
89
3 1 /2"
2443. RELAY AMPLIFIER FOR INTERCOMMUNICATING SYSTEMS.

It is suitable for video intercom systems where
it is necessary to have the intercommunicating service in different flats with privacy towards both outside and other users. Use
art.2443 in every intercommunicating flat.
Can be fixed on DIN bar or with two expansion
plugs. In housing DIN 4 modules A.
1471. RELAY UNIT.
Terminals
F General ground
B Power supply 8Vdc-60mA
Power supply 13Vac-70mA
12 Connection toward the microphone of the
monitors
12a Audio output from door station (transmitter
channel)
13 Connection towards the speaker of the monitors
13a Audio input from the door station (receiver
channel)
14 Timed power supply for the audio connection toward the door station 1224Vdc-60mA
0 From the jumper with F when the terminal 14
is powered to 12Vdc (terminal 8 of the monitor)
Terminals
1 13Vac input
2 24Vdc input
3 Ground
5 Common relay
6 Relay contact - ON
7 Relay contact - OFF
Note
If it is necessary to adjust the volume of the
intercommunicating audio turn trimmer R5.
Interruption of the control switching

ON in multi-way systems with 2 or
more audio-video entrances.
MEMORY
A low voltage, low current (DC/AC) unit, it

can switch voltages up to 50Vac/dc and 5A
max. Used for auxiliary services (e.g. stair
lights, call for 4 or more bells, door release
etc).
It installs on DIN bar or with two screws. In
housing DIN bar 3 modules A.
OFF (a)
6
7
8
9
12
13
To provide the service you must connect a relay

art.1471 for each control switch ON function to
be deactivated (or art. 1472 for every 2 control
switch ON).
14
10b 10a 11b 11a 12b 12a 13b 13a
WITHOUT COAX
Wire for control switch-ON

from monitor.
R5
AMPL.
10
11
12
13
12a
WITH COAX
1473. EXCHANGER.
It is different from the previous one in that it
has a reduced number of exchanges (4 instead of 7), and for the presence of 3 terminals (11, 12 and 13) for switching the relay
using a ground commands.
24
(9GB-2002)
13a
MODY
VIDEO MEMORY
42
5 1/4 "
1 5/8 "
VM 32. 32-image video memory.

It records the image, hour and date of the last
32-persons which have made a call from the
video-intercom panel.
This video memory can be connected to any
video-intercom system.
supplementary push-button on
the monitors. The video
memory should be powered
with 13V either ac or dc using
an external transformer or
power supply (e.g. PRS210).
123
IN
OUT
12V
8 + 3 3 D R A P
PUNTOVIRGOLA
*
SLIM
Operating instructions.
It is advisable to install the video memory
close to the monitor, using the push-button
command on the video memory. If the recommended configuration is not achievable or in
the system there is more than one monitor it
would be possible to connect in parallel to the
main commands (DEL, REC, AUTO and
PLAY) located on the video memory using the
Technical data
Power supply: 12Vac/dc
Current consumption: 0.4A
Video signal standard: CCIR
Recording delay after a call: 5 sec
Rec. inhibition after an image storing: 30sec
Memory capacity: 32 images
Hour, data maintaining in case of power failure:
5 min
PROJECT
5 1/8 "
130
Terminals
IN
Video input 1Vpp composite into 75
OUT Video output 1Vpp composite into 75
12V Power supply 12V either ac or dc
8 12Vdc input (from the monitor)
+ 12Vdc output (to the video distributors)
3 Ground
D Supplementary input of the Del command
R Supplementary input of the Rec command
A Supplementary input of the Auto command
P Supplementary input of the Play command
ERREP/R
133
INSTALLATION DIAGRAMS
Connection of the video memory in one-way systems.
In one-way systems with one or more monitors in parallel, it is sufficient to connect the
coaxial cable from the video camera unit to
the terminal IN of the video memory the
terminal OUT should be connected to the
video input of the monitor.
The connections P, A, R and D drawn with
dashed lines on the diagram, must be done
only if additional commands are required on
the monitor or if there is one or more monitors
in parallel.
PRS210
230V
127V
0
1 2 3
A
B
12V
P
A
R
D
8
OUT
OUT
position for one-way systems

position for multi-way systems
8 + 3 3 D R A P
25
(9GB-2002)
P1
P2
P3
P4
8
1
3
1
10
4
9
11
12
13
14
2
VC
T1
T2
T3
T4
8
1
3
1
10
4
9
11
12
13
14
2
VC
VM32
12V
12V
+
IN
IN
J1
VM
P
A
R
D
8
OUT
OUT
P1
P2
P3
P4
8
1
3
1
10
4
9
11
12
13
14
2
VC
T1
T2
T3
T4
8
1
3
1
10
4
9
11
12
13
14
2
VC
For the functioning of video memory, see the

instruction manual provided with the product.
WITH COAX
OUT
1 2 3
AS
IN
J1
PRS210
WITHOUT COAX
1 2 3
VM
To the timer and to the

video camera unit
To the riser of the videointercom system.
12V
12V
+
IN
IN
Connection of the video memory in multi-way systems.

In multi-way system, to avoid recording of
images directed to other monitors it is necessary to move the jumper J1 from position 12 to position 2-3; it is also necessary to
connect coaxial cable and positive power
230V
supply both of the video distributor and the
127V
monitor as shown in the diagram the connec0
DV
tions P, A, R and D drawn with dashed lines
+
on the diagram must be done only if addiOUT
tional commands are required on the monitor
OUT
(or if there is one or more monitors in parallel).
AS
VM32
MODY
INSTALLATION INSTRUCTIONS
ERREP/R
WIRE CROSS SECTION
50m
165 Ft
distance
100m 330 Ft
200m
660 Ft
300m
990 Ft
terminal
art. 1382
PROJECT
S mm
AWG
S mm
AWG
S mm
AWG
S mm
AWG
4 - 9 - 11 - 12 - 13
H-1-2-3-F-D
10 (call)
0.5
20
0.75
18
16
1.5
16
F - 14 - A - S
0.75
18
16
1.5
16
2.5
12
(cables in bold face type)
1304. Multipolar cable with 10

wires of different cross sections
and coaxial cable of 75. It can be
used in systems with a maximum
distance of 100 meters (50m between timer and camera unit and
50m between timer and monitor).
VIDEO SIGNAL DISTRIBUTION
Insertion loss
Max. input video signal
Bandwidth
IN
OUT 2
OUT 1
OUT 4
OUT 3
Serial connection of the coaxial cable (input and output from monitor)
Connection of the coaxial cable with video floor distributors
To carry out the video connection in a serial

mode it is necessary to cut the resistance of
75 located on the wall-bracket terminal
board. Leave it only on the last monitor. The
monitors serially connectable are max. 20.
For multi-way video systems it is advisable to

use floor video distributor that, being powered by the monitors connected to it (terminal
8), do not create overloads on the video
power supply. The outputs that are not used

must be closed with resistances of 75 that
are provided in kit. Maximum 12 video distributors can be connected together.
75
VC
PT5100
PT5160
WITHOUT COAX
PV1200
PV1260
75
8
1
3
1
2
4
20
75
75
8
1
3
1
VC
IN
OUT1
IN
1385R
VC
8
1
3
1 75
DV2-4
OUT2
VC
75
PT5600
PT5660
PT5800
PT5860
MD41
12
PV2100
PV2160
PT5600
PT5660
PT5800
PT5860
1385R
8
1
3
1
PT5100
PT5160
PV2100
PV2160
VC
8
1
3
1
MD41
WITH COAX
V
M
V
M
26
(9GB-2002)
IN
12Vdc2
50mA
100mA
0.8dB
2Vpp
>5MHz
DV2
DV4
Technical data
Power supply
Operating current
DV2-DV4. Video signal distributor.

They allow the distribution of the video signal
on 2 or 4 outputs. It can be installed on the
wall, on a wall box, with expansion plugs or it
can be placed in the junction box.
SLIM
Monitors terminal board

The resistance for closing of video signal
(75) is located on the terminal board of the
monitor wall bracket.
PUNTOVIRGOLA
For the video signal use a 75 low loss coaxial cable.
1
+
IN
DV2-4
OUT1
IN
OUT2
VC
8
1
3
1 75
PV1200
PV1260
MODY
INSTALLATION INSTRUCTIONS
Terminals
F General ground
14 Positive power supply
IN Video signal input
1-2-3-4-5 Video signal outputs
Video ground (shield of the coaxial cable)
75
75
20
VC
8
1
3
1
75
OUT1
IN
OUT2
75
PT 5100
PT 5160
VC
8
1
3
1
75
5600
5660
5800
5860
8
1
3
1
VC
IN
8
1
3
1 75
DV2-4
OUT1
IN
OUT2
PT
PT
PT
PT
PV 2100
PV 2160
1385R
8
1
3
1 75
DV2-4
MD41
OUT
2
4
5600
5660
5800
5860
1382
476
14
F
IN
V
M
1
3
SLIM
PT
PT
PT
PT
2
4
VC
VC
1
12
+
IN
PV 1200
PV 1260
PT 5100
PT 5160
8
1
3
1
PUNTOVIRGOLA
VC
In video systems with different

columns rising or with a high
number of users, it is necessary
to use the video distributor-amplifier art.476.
It is not necessary to close the
unused outputs on the 75 resistance.
PROJECT
Connection of the coaxial cable with distribution on maximum 5 column rising (serial and/or with video floor distributors)
Technical data
Power supply
21 3Vdc
Operating current at max. load
250mA
Gain at max. load from 0 to 3.5dB (adjustable)
Gain with one output closed to 75 from 0 to 9dB
(adjustable)
Bandwidth
>5MHz
0+50C
90% RH
Housing DIN 8 modules A
ERREP/R
476. Video distributor-amplifier.

It allows for the distribution of the video signal
coming from the cameras on 5 independent
lines. It is not necessary to close on 75 the
unused outputs.
14
F
Connection of coaxial cable with distribution on 9 columns rising

If more than one video distributor is to be
used, an extra supply, art. 1281 is necessary.
1385R
MD41
476
VC
75
2
4
5600
5660
5800
5860
IN
OUT
14 F
14 F
476
230V
127V
14 F
F
A
I
A
I
1281
1281
1382
Connection of art. 476 as video amplifier for long distance systems
For this use, one output is to be connected; do not close the other outputs on the 75 resistance.
8
1
3
1
PV 1200
PV 1260
MD41
3
OUT
V
M
IN
TR 1382
476
14
F
14
F
1281
F
A
I
27
(9GB-2002)
A
I
230V
127V
0
WITH COAX
1385R
75
PT
PT
PT
PT
IN
230V
127V
0
PV 2100
PV 2160
VC
1
20
8
1
3
1
PT 5100
PT 5160
3
OUT
WITHOUT COAX
V
M
MODY
WORKING INSTRUCTIONS
ERREP/R
*
PROJECT
*
PUNTOVIRGOLA
Check that the connections of the system are

carried out correctly.
Put the system in use by connecting the
power supply to the mains.
By pushing a call button from the external
push-button panel, it activates the bell of the
corresponding monitor and it activates the
system for a time of about 50 seconds. The
images appear on the monitor a few seconds
after the call.
Focus the scene to be filmed.
The user called, by lifting the handset, can
speak with the outside and at the same time
increase the activation time of the system
(about 3 minutes). If in the meantime another
call occurs, the monitor shuts itself off and
connects the last call. By replacing the handset the system shuts off automatically.
In case more calls occur simultaneously, a

protection circuit against overloading and
short circuiting is provided to disable the
timer and therefore to shut off the system.
In the absence of calls from the door station,
from any monitor (if provided in the system) it
is possible to control the entrance by pressing the button (control switch ON). Such a
control is not possible with an active system
and when a conversation is taking place. To
work the electric door lock release press the
button from monitor series Project and
PV1260. For the FLAT PV2160 monitor press
the button to the right of the handset. In the
two or more entrance systems all the audio
and video communications and door lock
release, from one entrance to the other, are
automatically switched with the call or the
control switch ON.
Connection of an additional power supply in systems with long distance

between the camera unit and the power supply base
In these systems the control switch ON from

the monitors can interrupt a running communication, for this reason it is advisable to
interrupt, by means of a relay 1471, all the
control switches ON when the video system is
active, giving the priority of the communication to the door stations (see page 24).
In systems with the intercommunicating service, the communication between monitors
and/or intercoms occur with system in standby.
Adjustments
All the regulations are carried out in the
factory. For possible corrections the intervention of a specialized technician is advisable. The Contrast and Brightness adjustments, being subject to the environmental
lighting conditions, are accessible from the
under neath by means of a screw driver.
Function of monitor main buttons

"door lock release"
SLIM
PT5160
V
M
H
H
D
1
2
3
1
2
3
4
F
A
S
UR
1382
SE
4
9
11
12
13
14
F
A
I
+
"control switch ON"
TR
PT5660
PT5860
PA
AL
AL
1281
1281
Mody
+
I
A
1
0
127V
230V
0
127V
230V
"door lock
release"
"control
switch ON"
WITHOUT COAX
Connection of an additional power supply in systems with long distance

between monitor and the power supply base
VC
D
3
S
1
2
H
F
A
1382
10
1
3
1
8
4
9
11
12
13
14
2
4
9
11
12
13
14
F
A
I
+
WITH COAX
1281
75
"door lock release"
"control switch ON"
"door lock release"
TR
AL
AL
PV2160
PV1260
A +
1281
+
I
A
0
127V
230V
0
127V
230V
28
(9GB-2002)
"control switch ON"
MODY
TROUBLESHOOTING
Audio section
Intercommunicating systems
Monitors shut OFF. Bells not functioning.

Control switching ON not functioning.
Absence of main voltage. Short circuits or
overloading of the output terminals of the
power supply and/or timer. Defective Power
supply. Defective timer.
No audio from either channel.

Absence of power supply voltage between 3
and 4 of the electronic door speaker (68Vdc).
Short circuit between 3 and F of the timer. The
11 wire is interrupted. Defective timer.
During the intercommunication the door

speaker is activated.
The video system is ON (privacy towards the
outside only when the video system is in
stand-by). The module for intercommunicating has not been plugged in the timer art.1443E.
Defective timer.
Image only slightly contrasted and/or out

of synchronism.
Coaxial cable loss or bad quality.
Coaxial cable not of 75. High distance system (use video amplifier art.476). Check the
correct connection of the coaxial cable (see
pages 26 and 27).
Radio reception on the door station.

The defect can occur when there is a transmitter working in the proximity. Apply a condenser from 0.1F between terminals 1 and 3
of the electric door speaker.
System with more entrances

Entrance A is never activated.
Short circuit between 5 and 6 of the exchanger. Defective exchanger.
Entrance B is never activated.
Short circuit between 3 and 4 of the exchanger. Defective exchanger. Absence of
power supply on 1 and 2 of the exchanger
(12Vac).
The electric door lock does not function.

Defective lock. The cross section of the wires
indicated in bold type is insufficient. A connecting wire to the lock has been interrupted.
The 9 wire is interrupted. Defective timer.
At the door station a whistle is heard

(Larsen effect).
The electric door speaker is badly housed in
the push-button panel (the microphone must
be stuck to the panel). Lower the volume.
The intercommunicating calls do not activate.

Check that the X1 and X2 wires are connected correctly. Check that the J1 jumper is
in intercommunication position see pages 3,
5, 7, 9 and 10).
WITHOUT COAX
Unfocused image.
Adjust correctly the lens of the camera. Defective camera.
Audio with humming in the background

(50/60 Hz).
The wires have been canalized together with
cables that power AC high absorption loads.
Separate the ground connection of the electric door speaker and of the name plate lights.
As visualized in the installation diagrams the
name plate lights must be powered from
terminals A and F of the power supply-timer
or when there are more than 8 lights from a
supplementary transformer (PRS 210). Defective power supply.
SLIM
The system does not shut OFF by replacing the handset.

Such a defect can also be due to the non
working audio system from the door station to
the monitors (see related chapter). Defective
timer. Defective electronic speaker.
No audio from the door station to the

monitors.
The 13 or 2 wire (from the timer to the door
station) is interrupted or has a short circuit.
Defective door speaker.
No audio in the intercommunicating service.

The wall-brackets of the monitors have the J1
jumper in position of audio privacy (see pages
3, 5, 7, 9 and 10). Defective module for
intercommunicating. Defective timer.
Control switch ON by monitors does not

function.
The 4 wire is interrupted. Defective timer.
No audio from the monitors to the door

station.
The 12 or 1 wire (from the timer to the door
station) is interrupted or has a short circuit.
Absence of the ground connection to terminal
4 of the electric door speaker. Defective door
speaker.
PUNTOVIRGOLA
Monitors turn ON. Absence of image.

The H wire is interrupted. The coaxial cable is
interrupted or has a short circuit. The shield of
the coaxial cable is interrupted. The video
distributors (if present), are not being powered. Defective camera unit.
Monitors shut OFF. Bells not functioning.

Control switch ON functioning.
The D wire is interrupted. Defective timer.
PROJECT
Defects and probable trouble
- Check the voltage output of the power

supply (see in detail the values indicated in
the power supply and control chapter).
- Check that the cross section of the wire
corresponds to what is indicated on page 26
and the descriptions of each diagram.
- Check that the connection of the wire corresponds to the installation diagram.
Preliminary checks
- Check for the presence of the mains voltage
between terminals 230 (or 127) and 0 of the
power supply.
but all of its outputs are protected against
overloading and short circuiting by temperature sensors. To reset the power supply, power must be cut off for about one minute and
can be restored after having eliminated the
defect.
ERREP/R
The probability of breakdown in the videointercom systems is obviously greater than in

the intercom system. Consequently this brief
troubleshooting takes into consideration the
most common defects. When a defect is
limited to only one monitor it is evident that
the trouble is a short circuit to the monitor
itself, to the connecting terminal board or to
the wires that go to the riser. The simplest
way to test the efficiency of a monitor is to try
if in another flat where everything functions
correctly.
WITH COAX
29
(9GB-2002)
MODY
*
ERREP/R
INSTALLATION DIAGRAMS
PROJECT
The following pages show the installation diagrams most often used in the video-intercom system. Upon request Farfisa supplies
installation diagrams for the configurations not present in this manual.
Multi-way systems with 1, 2 and 3 entrances

Combination intercom video-intercom systems
Multi-way systems with main entrance and auxiliary entrances
Intercommunicating multi-way systems with 1 or more entrances
One or two-way systems
One or two-way systems with intercommunicating service between monitor and intercom
PUNTOVIRGOLA
For a clearer understanding of the diagrams, the sequence of terminals in each individual article has not been followed. Only the
terminal code is valid (letter e/o number) not the graphic sequence.
The items may have more terminals than the ones in the installation diagrams. The excess terminals must not be utilized.
SLIM
The conduit of the wires of any video and video-intercom system must be carried out separately from the light or industrial system
as prescribed from the International standards.
It is advisable to provide behind the (fused spur) power supply a disconnecting and safety switch.
Before connecting the unit, make sure its data correspond to those of the mains.
The installation diagrams for 1 or more external stations illustrated in this technical manual have been represented with a one
monitor for each user. However, it is possible to personalise the installation by matching properly to the base diagrams of pages
31, 33, 37, 39, 41, 43, the applications of pages 50, 51, 52, 53, and 54. For further details, see page 48.
The installation diagrams from page 33 to page 47 use control panels of Mody or ErreP/R series (and camera unit 1385R), and
they can also be used for one-way installations and video kits of the Mody series. Connect one monitor, by using a one call wire,
and not the video distributor (the coaxial cable is connected directly to the monitor wall bracket).
Graphic designs
WITHOUT COAX
For a better comprehension of the installation diagrams we have made a list of the graphic symbols most often used.
Speaker
Coaxial cable
Microphone
Optional wire (usually control switching ON or intercommunicating calls)
Button
N2
Nn
Buzzer
Dashed line (for schematic purposes the first and last monitors are designed in the multi-family systems. Theoretically
the needed monitors are inserted in such dashed lines to
complete the system)
*
SR
40
Call wires (second and last)
Additional electronic bell
WITH COAX
Resistance
Lamp
30
(9GB-2002)
Graphic overlap point to adjust the application diagram to

the base diagram (see page 48).
MODY
Videokit series MODY

Monitor + accessories
External door station
Power supply
Timer
Intercommunicating module
MD41+MD72+MD11+MD30
1281
1382
MD41+MD72+MD11+MD30
1281
1382
PT5100MDCW
PT5160WLCD+WB5100
MD41C+MD72+MD11+MD30
1281
1382
PT5160MD
PT5160+WB5160
MD41+MD72+MD11+MD30
1281
1382
1443E
PT5160MDW
PT5160W+WB5160
MD41+MD72+MD11+MD30
1281
1382
1443E
PT5160MDCW
PT5160WLCD+WB5160
MD41C+MD72+MD11+MD30
1281
1382
1443E
PT5600MDW
PT5660W+WB5600+1283
MD41+MD72+MD11+MD30
1281
1382
PT5660W+WB5660+1283
MD41+MD72+MD11+MD30
1281
1382
1443E
PT5860W+WB5600
MD41+MD72+MD11+MD30
1281
1382
PT5860MDW
PT5860W+WB5660
MD41+MD72+MD11+MD30
1281
1382
1443E
PV1200MD
PV1260+WB1200+1283
MD41+MD72+MD11+MD30
1281
1382
PV1260MD
PV1260+WB1260+1283
MD41+MD72+MD11+MD30
1281
1382
1443E
PV2100MD
PV2160+WB2100
MD41+MD72+MD11+MD30
1281
1382
PV2160MD
PV2160+WB2160
MD41+MD72+MD11+MD30
1281
1382
1443E
PT5660MDW
PT5800MDW
PROJECT
PT5160+WB5100
PT5160W+WB5100
PT5100MD
PT5100MDW
ERREP/R
Videokit
MODY Videokit composition
PUNTOVIRGOLA
*
The base installation diagram of video kits

is in this same page.
To increase the number of inputs, use the
installation diagrams on pages 37, 39, 41, 43,
and add the missing articles.
For one-way systems with several monitors

and/or parallel intercoms, with or without intercommunicating service, see the application diagrams (from page 50 to 53), add the
missing articles.
Read page 48 carefully, for the composition
of the diagram desired.
SLIM
As a service ACI Farfisa supplies one-way

systems in Video Kits, which include all the
necessary articles, except cables and electric door lock (see the table above).
Si 5000M
ONE-WAY VIDEOKIT WITH APPLICATION OF THE MULTIPOLAR CABLE art.1304
Graphic overlap point for extension of diagram (see page 48).
MD41
coaxial
coaxial
light blue
MD11
SE
PA
black
green
white
pink
orange
grey
red
yellow
blue
4
9
D
H
1
2
3
11
12
13
14
F
A
I
+
F
S
A
black
green
light blue
yellow
white
pink
blue
red
8
1
3
1
4
9
10
11
12
13
14
2
VC
75
TR
1382
+
I
A
AL
max 50m
WITHOUT COAX
1
2
MD30 3
MD72
Art. 1304
Art. 1304
H
M
V
max 50m
1281
127V
230V
The 75 resistance inserted between

terminals 1 and 3 of monitors is supplied with
the product. It is not to be added.
31
(9GB-2002)
WITH COAX
1304. Multipolar cable with 10 wires of different cross sections and coaxial cable of
75. It can be used in systems with a maximum distance of 100 meters (50m between
timer and camera unit and 50m between timer
and monitor).
VC =PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
MODY
One and multi-way systems
VIDEO-INTERCOM SYSTEM WITH AUDIO-VIDEO PRIVACY
Si 5050
ERREP/R
Description
VC
...
DV
AL
TR
PA
SE
...
1
1
1
1
Monitor FLAT + wall bracket

Monitor + wall bracket + back box
Monitor reflex + wall bracket
Video floor distributors
Stabilized power supply
Audio-Video Timer
Door release button
Electric door lock (12Vac-1A)
Diagram ref. Q.ty Article
PROJECT
*
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
1281
1382
**
**
DV
9+coax
8+coax
PUNTOVIRGOLA
PT5160 +
WB5100
7+(n-1)+coax
SLIM
Mody series (see pages 16, 17, 18, 19 for the composition)
1 row
2 row
UR
1
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
Module frames and with back box
1
MD10-11-12 MD10-122-124 Modules for electric door speaker
...
MD21 24
MD222 228 Button modules
...
MD20 - 50
MD20 - 50
Blank and number modules
1
MD82 812 MD82 812
Hood covers
1
MD92 912* MD92 912* Rain shelters
PE
1
MD30
MD30
Electric door speaker
DV
9+coax
PV2160 +
WB2100
7+n+coax
1281
ErreP/R series (see pages 21, 22 for the composition)

UR
PB
PE
1
1
...
1
1
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters
1382
9+n+coax
... According to the number of users.

* The protective shelters are to be used instead
of back boxes and decorative shields.
** Articles not provided by ACI Farfisa.
Mody
SE
2
See page 28.
WITHOUT COAX
Note
- The A and F terminals of article 1382 can be
connected to a maximum of 8 lamps (24V3W). If this number is exceeded, one or more
12V transformers and an proper power will be
required (type PRS210).
- If the control switch ON is needed connect
terminal 4 of the timer (dashed line).
- For the cross section of the wires see the
table on page 26.
- To connect the coaxial cable see pages 26
and 27.
For one-way systems or video kits of the
Mody series, connect the coaxial cable directly to the monitor wall bracket, without
using the DV floor video distributor (see diagram on page 31).
PA
Application of MD100 and MD200 modules in one and multiway systems

N1 N2 N3 Nn
1382
TR
F A
9 11 12 13 14 F
H 1
2 3
A
I
A
I
+ 1281 AL
230V
127V
0
MD21
MD22
MD23
MD24
2
1
MD100
MD200
Mody
H
V
M
WITH COAX
MD41
PA
MD72-73-74
SE
32
(9GB-2002)
Si 5050
VIDEO-INTERCOM SYSTEM WITH AUDIO-VIDEO PRIVACY
ERREP/R
75
in
in
DV
MODY
VC n
8
1
3
1
4
9
10
11
12
13
14
2
+
out
75
PROJECT
*
PUNTOVIRGOLA
in
in
DV
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
+
out
75
2
4
SLIM
1
3

terminals 1 and 3 of monitors is supplied with
the product. It is not to be added.
TR
F A
Graphic overlap point for extension of

diagram (see page 48).
9 11 12 13 14 F
H 1
2 3
A
I
A
I
230V
127V
0
AL
ErreP/R
Mody
4
3
2
1
PE
PA
H
V
M
A
F
UR
UR
SE
33
(9GB-2002)
WITH COAX
H
V
M
PE
4
3
2
1
PB
WITHOUT COAX
PB
MODY
Multi-way systems
Si 5051
MULTI-WAY COMBINED INTERCOM VIDEO-INTERCOM SYSTEM WITH AUDIO-VIDEO PRIVACY
ERREP/R
Description
VC
...
CT
...

1 button intercom
2 button intercom
Conversation privacy module
Audio-Video Timer
Door release button
PROJECT
*
PUNTOVIRGOLA
SC
DV
AL
TR
PA
SE
...
...
1
1
1
1
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
PT510
PT520
SM50
DV2-4
1281
1382
**
**
DV
9+coax
8+coax
PT5160 +
WB5100
DV
9+coax
PV2160 +
WB2100
SLIM
1 row
2 row
UR
1
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
1
...
MD21 24
...
MD20 - 50
MD20 - 50
1
MD82 812 MD82 812
Hood covers
1
PE
1
MD30
MD30
PE
1
1
...
1
1
1385R
RP...
R...
290R/2 290R/38
337C
7+(n-1)+coax
7+n+coax
PT510+
SM50
1281

UR
PB
7+(n-2)+coax
1382
9+n+coax
Camera unit
Push-button panel
Push-button panel
Rain shelters
Mody
SE
2
PA

WITHOUT COAX
It is similar to the basic system described on
page 28, but with the following variations:
- from the intercom the user has about 40
seconds to answer by lifting the handset and
therefore can speak for an unlimited time with
video privacy towards the other users. By
replacing the handset the system shuts itself
OFF.
WITH COAX
Note
connected to a maximum of 8 lamps (24V-3W).
If this number is exceeded, one or more 12V
transformers and an proper power will be required (type PRS210).
- If secrecy of conversation is not needed, all
the systems 4+1 Farfisa can be used.
table on page 26.
and 27.
Connection of secrecy module to the terminal board of the system

Notes for systems of Project series:
- to cut the jumper W1 that links the
terminals 3 and 7.
- move the connection of the buzzer
from terminal 3 to 7.
- make the connection between terminal
7 of the intercom and the - (minus) of the
privacy module.
Cut the resistance R1 in all of the privacy modules.
W1
C
B
10K
2 1
R1
SM 50
34
(9GB-2002)
Si 5051
MULTI-WAY COMBINED INTERCOM VIDEO-INTERCOM SYSTEM WITH AUDIO-VIDEO PRIVACY
ERREP/R
75
in
in
DV
VC n
8
1
3
1
4
9
10
11
12
13
14
2
+
out
MODY
Multi-way systems
75
PROJECT
*
PUNTOVIRGOLA
in
in
DV
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
+
out
SLIM
The 75 resistance
inserted between terminals 1 and 3 of monitors
is supplied with the product. It is not to be added.
75
CT
CT + SC
Graphic overlap point

for extension of diagram (see page 48).
C
B
5
7
3
2
1
6
3
2
1
6
5
7
3
2
1
6
Intercom with audio privacy.
TR
F A
Intercom without
audio privacy.
9 11 12 13 14 F
H 1
2 3
A
I
A
I
230V
127V
0
AL
ErreP/R
Mody
4
3
2
1
PE
PA
H
V
M
A
F
UR
UR
SE
35
(9GB-2002)
WITH COAX
H
V
M
PE
4
3
2
1
PB
WITHOUT COAX
PB
MODY

Si 5150
ERREP/R
VIDEO-INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED ENTRANCES, ONE OF WHICH IS

ONLY AUDIO
Description
VC
...
DV
AL
TR
DS
PA
SE
...
1
1
1
2
2

Audio-Video Timer
Exchanger
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
1281
1382
1473
**
**
SLIM
1 row
2 row
UR
1
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
2
...
MD21 24
...
MD20 - 50
MD20 - 50
2
MD82 812 MD82 812
Hood covers
2
PE
2
MD30
MD30
UR
PB
PE
1
2
...
2
2
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters

WITHOUT COAX
*
Note
connected to a maximum of 6 lamps (24V3W). If this number is exceeded, one or more
12V transformers and an proper power will be
required (type PRS210).
- In this system the control switch ON from the
monitors can interrupt a running communication, for this reason it is advisable to interrupt
it by means of a relay art.1471 (see page 24).
table on page 26.
and 27.
Mody series, connect the coaxial cable directly to the monitor wall bracket, without
using the DV floor video distributor.
DV
9+coax
8+coax
It is similar to the basic system
described on page 28, but with
the following variations:
- Carrying out a call from the
entrance only audio, the corresponding monitor turns itself
ON without images.
- The audio-video operations
and the door lock release are
automatically switched at the
time of the call or with the
control switch ON.
PT5160 +
WB5100
7+(n-1)+coax
DV
9+coax
7+n+coax
PV2160 +
WB2100
1281
Mody
1382
1473
9+n+
coax
8+n
Mody
SE
SE
WITH COAX
36
(9GB-2002)
PA
PA
Si 5150
75
DV
The 75 resistance inserted between terminals 1 and 3 of monitors is

supplied with the product. It is not to
be added.
75
PROJECT
Nn
VC n
8
1
3
1
4
9
10
11
12
13
14
2
+
out
ERREP/R
VIDEO-INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED ENTRANCES, ONE OF WHICH IS

ONLY AUDIO
in
in
MODY
in
in
DV
9 11 12 13 14 F
F A
H 1
A
I
A
I
75
SLIM
TR
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
+
out
PUNTOVIRGOLA
Graphic overlap point for extension

of diagram (see page 48).
230V
127V
0
AL
ErreP/R
Mody
"b"
"a"
PB
PB
PB
Nn
Nn
7
9 10 5
N1
PE
PE
4
3
2
1
N1
6
10a
9a
10b
9b
DS
4
3
2
1
ErreP/R
PE
4
3
2
1
WITHOUT COAX
Mody
"a"
8b
8a
UR
UR
1
2
7a
PA
7b
PA
SE
SE
37
(9GB-2002)
WITH COAX
H
V
M
H
V
M
A
F
MODY

Si 5250
ERREP/R
VIDEO-INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED VIDEO ENTRANCES
Description
VC
...
DV
AL
TR
DS
PA
SE
...
1
1
1
2
2

Audio-Video Timer
Exchanger
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
1281
1382
1273TV
**
**
SLIM
1 row
2 row
UR
2
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
2
...
MD21 24
...
MD20 - 50
MD20 - 50
2
MD82 812 MD82 812
Hood covers
2
PE
2
MD30
MD30
UR
PB
PE
2
2
...
2
2
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters

DV
9+coax
8+coax
WITHOUT COAX
*
WITH COAX
Note
- To have the control switch ON for the 2 video
entrances it is necessary to make the dashed
line connections and use WB5160, WB5660,
WB2160, WB1260 wall brackets.
- The wall brackets are configurated to work
without the audio privacy, to restore it the
jumper J1 must be moved (see pages 3, 5, 7, 9
and 10).
monitors can interrupt a running communication, for this reason it is advisable to interrupt it
by means of a relay art.1471 (see page 24).
table on page 26.
and 27.
Mody series, connect the coaxial cable directly to the monitor wall bracket, without using
the DV floor video distributor.
- the audio-video operations
time of the call or with the control switch ON.
PT5160 +
WB5100
7+(n-1)+coax
DV
9+coax
7+n+coax
PV2160 +
WB2100
1281
1382
9+n+
coax
Mody
SE
1273TV
9+n+
coax
SE
38
(9GB-2002)
Mody
PA
PA
Si 5250
ERREP/R
VIDEO-INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED VIDEO ENTRANCES
75
in
in
DV
VC n
PUNTOVIRGOLA
Graphic overlap point for extension of

diagram (see page 48).
PROJECT
Nn
75
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
T1
+
out

terminals 1 and 3 of monitors is supplied
with the product. It is not to be added.
in
in
DV
SLIM
9 11 12 13 14 F
H 1
A
I
A
I
230V
127V
0
AL
ErreP/R
ErreP/R
Mody
Mody
"b"
"a"
PB
Nn
9
PE
7 10 11 12 13 5
13a
12a
11a
13b
12b
11b
4
3
2
1
10b
9b
8b
H
V
M
DS
7b
PA
PA
4
3
2
1
PE
H
V
M
A
F
UR
UR
SE
SE
39
(9GB-2002)
PE
WITH COAX
UR
UR
10a
9a
8a
1
2
7a
H
V
M
H
V
M
A
F
N1
6
4
3
2
1
PB
Nn
N1
4
3
2
1
"b"
PB
WITHOUT COAX
"a"
PE
75
F A
PB
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1
+
out
TR
MODY
MODY

Si 5256
ERREP/R
VIDEO INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED ENTRANCES, ONE WITH AN OUTDOOR
OR INDOOR SURVEILLANCE CAMERA
Description
VC
...
DV
AL
TR
DS
IN
PA
SE
...
1
1
1
1
2
2

Audio-Video Timer
Exchanger
Relay unit
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
1281
1382
1273TV
1471
**
**

TE
SLIM
LL
1
1
1
1
1
1
TVT...
H...
CU...
AST..
APS...
**
Surveillance camera
Lens with or without auto-iris
Climatized housing for outside
Jointed bracket for interior or housing
Power supply for camera
Lamp with maximum power of 800W
1 row
2 row
UR
1
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
2
...
MD21 24
...
MD20 - 50
MD20 - 50
2
MD82 812 MD82 812
Hood covers
2
PE
2
MD30
MD30
UR
PB
PE
1
2
...
2
2
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters
DV

* The protective shelters are to be used instead of back boxes and decorative shields.
WITHOUT COAX
*
WITH COAX
Note
- To have the control switch ON for the 2 video
entrances it is necessary to make the dashed
line connections and use WB5160, WB5660,
WB2160, WB1260 wall brackets.
- The wall brackets are configurated to work
without the audio privacy, to restore it the
jumper J1 must be moved (see pages 3, 5, 7, 9
and 10).
monitors can interrupt a running communication, for this reason it is advisable to interrupt it
by means of a relay art.1471 (see page 24).
table on page 26.
and 27.
9+coax
8+coax
PT5160 +
WB5100
For one-way systems or video

kits of the Mody series, connect the coaxial cable directly
to the monitor wall bracket, without using the DV floor video
distributor.
- the audio-video operations
time of the call or with the control switch ON.
- The surveillance camera remains in function in a timed
mode.
40
(9GB-2002)
7+(n-1)+coax
DV
9+coax
7+n+coax
PV2160 +
WB2100
1281
1382
9+n+
coax
Mody
SE
1273TV
T V T. . + H . . . +
C U . . . + A S T. .
+APS...
9+n+coax
Mody
SE
PA
1471
PA
Si 5256
ERREP/R
VIDEO INTERCOM SYSTEM WITH TWO AUTOMATICALLY SWITCHED ENTRANCES, ONE WITH
AN OUTDOOR OR INDOOR SURVEILLANCE CAMERA
75
in
in
DV
VC n
PUNTOVIRGOLA

PROJECT
Nn
75
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
T1
+
out

terminals 1 and 3 of monitors is supplied
with the product. It is not to be added.
in
in
DV
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1
+
out
F A
SLIM
75
TR
9 11 12 13 14 F
H 1
MODY
A
I
A
I
230V
127V
0
AL
ErreP/R
Mody
"b"
"a"
"a"
PB
Nn
Nn
9
7 10 11 12 13 5
N1
N1
6
PE
PE
4
3
2
1
13a
12a
11a
4
3
2
1
13b
12b
11b
9b
8b
10b
LL
PE
2
3
7b
PA
PA
SE
41
(9GB-2002)
IN
3
SE
1
230V
5
6
WITH COAX
UR
UR
DS
10a
9a
8a
1
2
7a
H
V
M
H
V
M
A
F
TE
4
3
2
1
L
N
230V
PB
PB
WITHOUT COAX
ErreP/R
Mody
MODY

Si 5350
VIDEO-INTERCOM SYSTEM WITH THREE AUTOMATICALLY SWITCHED VIDEO ENTRANCES
ERREP/R
Description
VC
...
DV
AL
TR
DS
PA
SE
...
1
1
2
3
3

Audio-Video Timer
Exchanger
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
1281
1382
1273TV
**
**
SLIM
1 row
2 row
UR
3
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
3
...
MD21 24
...
MD20 - 50
MD20 - 50
3
MD82 812 MD82 812
Hood covers
3
PE
3
MD30
MD30
UR
PB
PE
3
3
...
3
3
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters

DV
9+coax
8+coax
WITHOUT COAX
Note
- The A and F terminals of article 1382 can be connected to a
maximum of 5 lamps (24V-3W). If this number is exceeded, one or
more 12V transformers and an proper power will be required (type
PRS210).
- To have the control switch ON for the 3 video entrances it is
necessary to make the dashed line connections and use WB5160,
WB5660, WB2160, WB1260 wall brackets.
- The wall brackets are configurated to work without the audio
privacy, to restore it the jumper J1 must be moved (see pages 3, 5, 7,
9 and 10).
- In this system the control switch ON from the monitors can interrupt
a running communication, for this reason it is advisable to interrupt
it by means of a relay art.1471 (see page 24).
- For the cross section of the wires see the table on page 26.
- To connect the coaxial cable see pages 26 and 27.
For one-way systems or video kits of the Mody series, connect the
coaxial cable directly to the monitor wall bracket, without using the
DV floor video distributor.
It is similar to the basic system described on page 28, but with the
following variations:
- the audio-video operations and the door lock release are automatically switched at the time of the call or with the control switch ON.
PT5160 +
WB5100
DV
9+coax
WITH COAX
42
7+n+coax
PV2160 +
WB2100
1281
9+n+
coax
Mody
1382
1273TV
9+n+
coax
Mody
SE
(9GB-2002)
7+(n-1)+coax
9+n+
coax
Mody
SE
PA
1273TV
SE
PA
PA
Si 5350
VIDEO-INTERCOM SYSTEM WITH THREE AUTOMATICALLY SWITCHED VIDEO ENTRANCES
ERREP/R
75
in
in
DV
VC n
Nn
PROJECT

75
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
T1
T2
+
out
The 75 resistance inserted between terminals 1 and 3 of monitors

is supplied with the product. It is not
to be added.
DV
VC 1
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1
P2
+
out
F A
9 11 12 13 14 F
H 1
A
I
A
I
"c"
MD
7 10 11 12 13 5
ErreP/R
MD
Nn
9
2
4
230V
127V
0
AL
Mody
1
3
SLIM
75
TR
PUNTOVIRGOLA
in
in
MODY
3
N1
4
DS
4
3
2
1
13b
12b
11b
Mody
H
V
M
9a 8a 7a 10a 11a 12a 13a 6 7b
H
V
M
A
F
UR
PA
PE
UR
SE
"a"
Mody
"a"
PB
PB
PE
7 10 11 12 13 5
13a
12a
11a
13b
12b
11b
4
3
2
1
10b
9b
8b
H
V
M
DS
7b
PA
SE
43
(9GB-2002)
4
3
2
1
PE
H
V
M
A
F
UR
PA
SE
PE
UR
WITH COAX
UR
UR
10a
9a
8a
1
2
7a
H
V
M
H
V
M
A
F
N1
6
4
3
2
1
PB
Nn
8
N1
4
3
2
1
ErreP/R
PB
Nn
9
PE
"b"
WITHOUT COAX
10b
9b
8b
1
2
ErreP/R
4
3
2
1
PE
MODY
Multi-way systems
Si 5550
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH AUXILIARY AUDIO ENTRANCES AND ONE MAIN VIDEO
ENTRANCE ACCORDING TO THE STAIRWAY
Description
VC
...
DV
AV
AL
TR
DS
PA
SE
...
1
1+X
1+X
X
1+X
1+X

Video distributor-amplifier
Audio-Video Timer
Exchanger
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
476
1281
1382
1273TV
**
**
SLIM
1 row
2 row
UR
1
MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
1+X MD10-11-12 MD10-122-124 Modules for electric door speaker
...
MD21 24
...
MD20 - 50
MD20 - 50
1+X MD82 812 MD82 812
Hood covers
1+X MD92 912* MD92 912* Rain shelters
PE
1+X MD30
MD30
The push-button panel of the main video entrance must have separate commons. A common for every auxiliary entrance. The buttons of
Mody series can be divided in groups of 2.

UR
PB
PE
1
1+X
...
1+X
1+X
1385R
RP...
R...
290R/2 290R/38
337C
common buttons 1
and 2
Camera unit
Push-button panel
Push-button panel
Rain shelters
to separate buttons
common cut here
common buttons 3
and 4

X According to the number of auxiliary entrances.
"a"
"b"
DV
DV
9+coax
9+coax
8+coax
PT5160 +
WB5100
WITHOUT COAX
- the audio-video operations and the door lock release are
automatically switched at the time of the call or with the control
switch ON.
- Carrying out a call from the entrance only audio, the corresponding monitor turns itself ON without images.
- The services towards the auxiliary audio entrances are independent among themselves and therefore they can function at
the same time.
8+coax
PV 1260
+ 1283
7+(n-1)
+coax
7+(n-1)
+coax
DV
DV
9+coax
9+coax
1281
1382
1273TV
7+n+coax
Mody
8+n
PT5660+WB5600+1283
PT5860+WB5600
1281
WITH COAX
Note
The 75 resistance inserted between terminals 1 and 3 of
monitors is supplied with the product. It is not to be added.
maximum of 5 lamps (24V-3W). If this number is exceeded, one
or more 12V transformers and an proper power will be required
(type PRS210).
- In this system the control switch ON from the monitors can
interrupt a running communication, for this reason it is advisable
to interrupt it by means of a relay art.1471 (see page 24).
7+n+coax
PV 2160 +
WB 2100
Mody
SE
1273TV
8+n
8+n+
coax
PA
1382
SE
8+n+
coax
PA
Mody
8+X+n
+coax
7+(X-1)+
n+coax
"p"
9+coax
2
44
(9GB-2002)
SE
PA
1281
1382
476
7+(X-2)+
n+coax
Si 5550
"A"
75
"B"
75
+
out
DV
VC n
in
75
in
DV
in
75
in
VC 1
N1 (a)
AL
A
I
230V
127V
0
A
I
11 14 13 12 4
F A S H
AL
TR
in
in
N1 (b)
A
I
230V
127V
0
9 3 2 1 D
+
out
8
1
3
1
2
4
9
10
11
12
13
14
P1
A
I
11 14 13 12 4
F A S H
PUNTOVIRGOLA* SLIM
+
out
8
1
3
1
2
4
9
10
11
12
13
14
P1
in
75
in
Nn (b)
DV
VC 1
DV
PROJECT
Nn (a)
75
+
out
8
1
3
1
2
4
9
10
11
12
13
14
T1
8
1
3
1
2
4
9
10
11
12
13
14
T1
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH AUXILIARY AUDIO ENTRANCES AND ONE MAIN VIDEO
VC n
MODY
Multi-way systems
TR
9 3 2 1 D
(b)
(a)
PB
PB
Nn (a)
Nn (b)
N1 (a)
N1 (b)
4 7b 13 12 11 3
PE
4
3
2
1
7 8 9 10
4 7b 13 12 11 3
PE
13b
12b
11b
DS
4
3
2
1
13b
12b
11b
10b
9b
8b
1
2
DS
10b
9b
8b
1
2
6 13a 12a 11a 10a 7a
6 13a 12a 11a 10a 7a
5 8a 9a
PA
SE
7 8 9 10
5 8a 9a
PA
SE
WITHOUT COAX
(p)
OUT 2
Nn (a)
OUT
OUT 3
AV
N1 (a)
PB
IN
OUT 4
14
Nn (b)
N1 (b)
PE
4
3
2
1
H
V
M
" C ... "
PA
SE
S
11 2
TR
A
I
F
A
I
45
(9GB-2002)
AL
230V
127V
0
WITH COAX
UR
MODY
Multi-way systems
Si 5551
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH AUXILIARY VIDEO ENTRANCES AND ONE MAIN VIDEO
Description
VC
...
DV
AV
AL
TR
DS
PA
SE
...
1
1+X
1+X
X
1+X
1+X

Video distributor-amplifier
Audio-Video Timer
Exchanger
Door release button
PROJECT
*
PUNTOVIRGOLA
PT 5160 + WB 5100
PT 5660 + WB 5600 + 1283
PT 5860 + WB 5600
PV 1260 + WB1200 + 1283
PV 2160 + WB 2100
DV2-4
476
1281
1382
1273TV
**
**
SLIM
1 row
2 row
UR
1 +X MD41
MD41
Camera module
PB
...
MD72-73-74 MD72-73-74
1+X MD10-11-12 MD10-122-124 Modules for electric door speaker
...
MD21 24
...
MD20 - 50
MD20 - 50
1+X MD82 812 MD82 812
Hood covers
1+X MD92 912* MD92 912* Rain shelters
PE
1+X MD30
MD30
The push-button panel of the main video entrance must have separate commons. A common for every auxiliary entrance. The buttons of
Mody series can be divided in groups of 2.
common buttons 1
and 2
UR
PB
to separate buttons
common cut here
PE
1+X
1+X
...
1+X
1+X
1385R
RP...
R...
290R/2 290R/38
337C
Camera unit
Push-button panel
Push-button panel
Rain shelters
common buttons 3
and 4

X According to the number of auxiliary entrances.
"a"
"b"
DV
DV
9+coax
9+coax
8+coax
PT5160 +
WB5100
WITHOUT COAX
- The audio-video operations and the door lock release are
automatically switched at the time of the call or with the control
switch ON.
- The services towards the auxiliary video entrances are independent among themselves and therefore they can function at the same
time.
8+coax
PV 1260
+ 1283
7+(n-1)
+coax
7+(n-1)
+coax
DV
DV
9+coax
9+coax
7+n+coax
1281
1382
Mody
Mody
1273TV
9+n+
coax
PT5660+WB5600+1283
PT5860+WB5600
1281
2
4
7+n+coax
PV 2160 +
WB 2100
WITH COAX
Note
The 75 resistance inserted between terminals 1 and 3 of
monitors is supplied with the product. It is not to be added.
maximum of 6 lamps (24V-3W). If this number is exceeded, one or
more 12V transformers and an proper power will be required (type
PRS210).
- To have the control switch ON for the 3 video entrances it is
necessary to make the dashed line connections and use WB5160,
WB5660, WB2160, WB1260 wall brackets.
- The wall brackets are configurated to work without the audio
privacy, to restore it the jumper J1 must be moved (see pages 3, 5,
7, 9 and 10).
- In this system the control switch ON from the monitors can
interrupt a running communication, for this reason it is advisable to
interrupt it by means of a relay art.1471 (see page 24).
1
3
SE
1273TV
9+n+
coax
8+n+
coax
PA
1382
SE
8+n+
coax
PA
Mody
8+X+n
+coax
7+(X-1)+
n+coax
"p"
9+coax
2
46
(9GB-2002)
SE
PA
1281
1382
476
7+(X-2)+
n+coax
Si 5551
"A"
75
"B"
75
+
out
DV
VC n
in
75
in
DV
8
1
3
1
2
4
9
10
11
12
13
14
P1
in
in
75
VC 1
N1 (a)
+
out
8
1
3
1
2
4
9
10
11
12
13
14
P1
in
in
N1 (b)
PUNTOVIRGOLA
+
out
75
in
in
Nn (b)
DV
VC 1
DV
PROJECT
Nn (a)
75
+
out
8
1
3
1
2
4
9
10
11
12
13
14
T1
8
1
3
1
2
4
9
10
11
12
13
14
T1
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH AUXILIARY VIDEO ENTRANCES AND ONE MAIN VIDEO
VC n
MODY
Multi-way systems
AL
A
I
230V
127V
0
A
I
11 14 13 12 4
F A S H
AL
TR
SLIM
1
3
A
I
230V
127V
0
9 3 2 1 D
A
I
11 14 13 12 4
F A S H
TR
9 3 2 1 D
(b)
(a)
PB
PB
Nn (a)
Nn (b)
N1 (a)
N1 (b)
4 7b 13 12 11 3
PE
4
3
2
1
4 7b 13 12 11 3
7 8 9 10
PE
13b
12b
11b
DS
10b
9b
8b
1
2
H
V
M
UR
13b
12b
11b
DS
10b
9b
8b
1
2
H
V
M
UR
6 13a 12a 11a 10a 7a
5 8a 9a
6 13a 12a 11a 10a 7a
PA
SE
4
3
2
1
7 8 9 10
5 8a 9a
PA
SE
WITHOUT COAX
(p)
OUT 2
Nn (a)
OUT
OUT 3
AV
N1 (a)
PB
IN
OUT 4
14
Nn (b)
N1 (b)
PE
4
3
2
1
H
V
M
" C ... "
PA
SE
S
11 2
TR
A
I
F
A
I
47
(9GB-2002)
AL
230V
127V
0
WITH COAX
UR
MODY
Working diagrams
ERREP/R
EXTENSION OF VIDEO INTERCOM SYSTEM
PROJECT
*
PUNTOVIRGOLA
All installation diagrams in this technical manual we have used only

one monitor for each user. It is possible to personalise the installation, by matching properly to the base diagrams of pages 31, 33, 35,
37, 39, 41, 43, the applications on the following pages (50 to 54). Such
examples refer to applications with a one video-intercom entrance. To
plan systems with 2 or more audio-video entrances, and if more than
one control switch-ON is needed, use the first buttons of monitor (P1,
P2 or T1, T2, etc.), by making the terminals for intercommunicating
calls slide on to the lower ones (P3, P4 or T3, T4).
In the base diagrams the dashed lines identify the wires for control
switch-ON, whereas in the additional diagrams the dashed lines
refer to the wires for intercommunicating service.
When the simultaneous switch-ON of several monitors is needed,
and extra power supplies are to be added, take care that terminal I of
timer 1382 can be connected to a maximum of 3 power supplies
1281.
Extension of a ONE-WAY system

To plan a one-way system with several monitors and/or parallel
intercoms and with or without intercommunicating service, proceed as follows.
- make a photocopy of the additional diagram desired, selecting it
between those of pages 50, 51, 52, 53;
- cut vertically the diagram in correspondence to the arrow *
;
- put the diagram on the base diagram, so as to cover the existing
monitor, then line up the wires of the 2 diagrams;
- if specified in the additional diagram, connect the I and A wires to
the terminals of article 1382;
- to obtain the intercommunicating service, make the connections
which have been drawn with a dashed line.
Example: by making a photocopy of the additional diagram of page

50 (3 parallel monitors), then applying it on to the installation diagram
of page 39 (Si 5250), and lining it up to the riser wires, it is possible
to obtain a one-way system, with 3 parallel monitors connected to 2
external video stations.
SLIM
To P3 terminal
To the terminal I
of art.1382
WITHOUT COAX
*
WITH COAX
48
(9GB-2002)
MODY
Working diagrams

amongst those of pages 50, 51, 52, 53;
- cut vertically the diagram in correspondence to the arrow * ;
- if specified in the additional diagram, connect the I and A wires to
the terminals of article 1382;
- if the base diagram includes the DV video distributor, remember to
connect the terminal + to the terminal 8 of all monitors;

amongst those of page 54;
- cut vertically the diagram in correspondence to the arrow *
;
- repeat the operations for the application in other apartments;
- if the base diagram includes the DV video distributor, remember to
connect the terminal + to the terminal 8 of all monitors;
- to obtain the intercommunicating service, make the connections
which have been drawn with a dashed line.
SLIM

52 (1 monitor and 2 parallel intercoms), then applying it on to the
installation diagram of page 43 (Si 5350), and lining it up to the riser
wires, it is possible to obtain a multi-way system, with 1 monitor and
2 parallel intercoms in one apartment, connected to 3 external video
stations.

54 (1 monitor and 2 parallel intercoms), then applying it on to the
installation diagram of page 43 (Si 5350), and lining it up to the riser
wires, it is possible to obtain a multiway system in one or more
apartments, with 1 monitor and 2 parallel intercoms, connected to 3
external video stations.
Note. if the intercommunicating service between monitors or systems

is also needed, once the system is on, the user can listen to other
users, who are speaking to the outside.
If such an option is not desired, use the diagrams of page 54 to make
the extension (see the following chapter).
PUNTOVIRGOLA
To plan a multi-way system, with several monitors and/or parallel

intercoms, in 2 or more apartments, with or without intercommunicating service, proceed as follows:
To plan a multi-way system with several monitors and/or parallel

intercoms in a one apartment, with or without intercommunicating
service, proceed as follows:
PROJECT
Extension of a MULTI-WAY installation in several apartments
Extension in a one apartment of a MULTI-WAY system
ERREP/R
EXTENSION OF VIDEO INTERCOM SYSTEM
FLOOR CALL
VC
8
1
3
1
4
9
10
11
12
13
14
2
X2
X1
Floor push-button
VC
Floor push-button
8
1
3
1
4
9
10
11
12
13
14
2
X2
X1
WITHOUT COAX
Notes
Floor calls are available in videointercom installations
with coaxial cable. To provide the service, you must use
wall-mounting brackets (WB5160, WB5660, WB2160
or WB1260), add a wire in the riser and connect the floor
button as shown in the enclosed diagram.
A continuous tone different from the external push-button
panel modulated tone is generated when pressing the
floor button.
In installations with intercommunication service the same
continuous tone is used for floor and intercom calls.
WITH COAX
To the terminal A of the

timer art.1382
49
(9GB-2002)
MODY
Working diagrams
ERREP/R
ADDITIONAL DIAGRAM FOR 2 PARALLEL MONITORS
PROJECT
*
Terminal A
(art.1382)
PUNTOVIRGOLA
VC1
VC2
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
X2
VC =PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
75
or, if intercommunicating
VC =PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
P1-T1
symbol for terminal monitor PT5160,

PT5660, PT5860, PV1260
symbol for terminal

monitor PV2160
Terminal I
(art.1382)
I
A +
AL
2
4
SLIM
To have the intercommunicating service, make the connections which have been drawn with a dashed line, then
insert in the timer, art.1382, the module for intercommunicating, art.1443E, which is included in the video kit (see
page 23).
Graphic overlap point for

extension of diagram (see
page 48).
1
3
1281
127V
230V

page 48).
WITHOUT COAX
VC1
VC2
VC3
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
X2
P2-T2
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
X2
75
VC =PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
VC =PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
P1-T1

PT5660, PT5860, PV1260
Terminal I
(art.1382)
I
A +
AL
1281
1
0
127V
230V
WITH COAX
page 23).
50
(9GB-2002)
symbol for terminal

monitor PV2160
MODY
Working diagrams
ERREP/R

VC4
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
P3-T3
P4-T4
1 3 5 6
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
X2
P2-T2
P3-T3
P4-T4
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
X2
P3-T3
P4-T4
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
P3-T3
X2
P4-T4
75
PUNTOVIRGOLA
VC3
VC2
PROJECT
IN 1471
VC1
P1-T1
Terminal I
(art.1382)
1281
A +
AL
page 23).
symbol for terminal

monitor PV2160
A +
AL
0
127V
230V
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
SLIM
127V
230V
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283

page 48).
1281
*
IN 1471
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
P3-T3
P4-T4
1 3 5 6
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
X2
P2-T2
P3-T3
P4-T4
VC3
VC4
VC5
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
X2
P3-T3
P4-T4
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
P3-T3
X2
P4-T4
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
P3-T3
P4-T4
X2
P1-T1
1281
1281
A +
AL
0
127V
230V
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
51
(9GB-2002)
A +
symbol for terminal

monitor PV2160
AL
0
127V
230V
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
WITH COAX
page 23).
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
75

page 48).
VC2
WITHOUT COAX
Terminal I
(art.1382)
VC1
MODY
Working diagrams
ERREP/R
ADDITIONAL DIAGRAM FOR 1 MONITOR AND 1 INTERCOM

VC
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
PROJECT
Terminal A
(art.1382)
PUNTOVIRGOLA
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
CT1
75
5
6
3
1
2
7
X1
P1
X2
CT =
PT510
PV100
924
SR40
PT520 + SR40 + PT501
P1-T1
symbol for terminal

monitor PV2160
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
SLIM
page 23).
In all intercoms cut the W1 jumper which links the terminals
3 and 7. Then apply the electronic bell SR40.

page 48).
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
ADDITIONAL DIAGRAM FOR 1 MONITOR AND 2 PARALLEL INTERCOMS
*
VC
WITHOUT COAX
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
Terminal A
(art.1382)
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
CT1
75
CT2
5
6
3
1
2
5
6
3
1
2
7
X1
P1
X2
P2
7
X1
P1
P2
X2
CT =
PT510
PV100
924
SR40
PT520 + SR40 + PT501
P1-T1
symbol for terminal

monitor PV2160
WITH COAX
page 23).
3 and 7. Then apply the electronic bell SR40 and the button
groups.
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
9 7
6 3 2 1 5 P1
P2
PT520
P3
Note
In all the intercommunicating intercoms, connect one of the two terminals of the single
button group to terminal 7.
52
(9GB-2002)
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
MODY
Working diagrams
ERREP/R
*
75
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
2
4
symbol for terminal

monitor PV2160
5
6
3
1
2
5
6
3
1
2
5
6
3
1
2
7
X1
P1
X2
P2
P3
7
X1
P1
P2
X2
P3
7
X1
P1
P2
P3
X2
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
SR40
CT =PT510; PV100; 924

PT520 + SR40 + PT501
SLIM
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
page 23).
groups.
CT3
1
3
P1-T1
CT2
PUNTOVIRGOLA
Terminal A
(art.1382)
CT1
1 3 5 6
PROJECT
IN 1471
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
P3-T3
VC
9 7
6 3 2 1 5 P1
P2
PT520
P3
Note

page 48).
*
IN 1471
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
P3-T3
P4-T4
1 3 5 6
75
Terminal A
(art.1382)
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
P1-T1
symbol for terminal

monitor PV2160
CT2
CT4
CT3
5
6
3
1
2
5
6
3
1
2
5
6
3
1
2
5
6
3
1
2
7
X1
P1
X2
P2
P3
P4
7
X1
P1
P2
X2
P3
P4
7
X1
P1
P2
P3
X2
P4
7
X1
P1
P2
P3
P4
X2
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
53
(9GB-2002)
CT =PT510; PV100; 924

PT520 + SR40 + PT501
9 7
6 3 2 1 5 P1
P2
PT520
P3
Note
WITH COAX

page 48).
SR40
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
page 23).
groups.
CT1
WITHOUT COAX
VC
MODY
Working diagrams
ADDITIONAL DIAGRAM FOR MULTI-WAY SYSTEMS WITH 3 INTERCOMMUNICATING PARALLEL MONITORS
ERREP/R
VC1
VC2
VC3
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
X2
P2-T2
8
1
3
1
4
9
10
11
12
13
14
2
X1
P1-T1
P2-T2
X2
(Diode 100V-1A / type 1N4002)
PROJECT
75
VC =PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
PUNTOVIRGOLA
VC =PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
P1-T1

PT5660, PT5860, PV1260
13a 12a 12 13 14 O F
2 5 3 6
A +
SLIM
2443
AL
1471 IN
SA
symbol for terminal monitor

PV2160
1281
1
0
127V
230V

page 48).
ADDITIONAL DIAGRAM FOR MULTI-WAY SYSTEMS WITH 1 MONITOR AND 2 PARALLEL INTERCOMS
*
VC
(Diode 100V-1A / type 1N4002)
WITHOUT COAX
8
1
3
1
4
9
10
11
12
13
14
2
X1
X2
P1-T1
P2-T2
13a 12a 12 13 14 O F B
2443
CT1
75
+
AL
SA
CT2
5
6
3
1
2
5
6
3
1
2
7
X1
P1
X2
P2
7
X1
P1
P2
X2
CT =
PT510
PV100
924
SR40
9 7
6 3 2 1 5 P1
PRS231
P2
PT520
127V
230V
WITH COAX
symbol for terminal

monitor PT5160,
PT5660, PT5860,
PV1260
P1-T1
symbol for terminal

monitor PV2160
P3
Note
In all intercoms cut the W1 jumper which links the
terminals 3 and 7. Then apply the electronic bell
SR40 and the button groups.
54
(9GB-2002)
PT520 + SR40 + PT501
VC =
PT5160 + WB5100
PT5660 + WB5600 + 1283
PT5860 + WB5600
PV2160 + WB2100
PV1260 + WB1200 + 1283
PT5160 + WB5160
PT5660 + WB5660 + 1283
PT5860 + WB5660
PV2160 + WB2160
PV1260 + WB1260 + 1283
MODY
4+1 VIDEO-INTERCOM SYSTEM
PEP
1S
3 9 /16"
ANTILOCALE
19
3
Lamp terminals
Button terminal board
Call buttons common (terminal C)
Stair light button terminals
External volume adjustment
Feedback adjustment
Terminal board for audio/powering/elect. lock
124
4 7 /8"
52
2 1 /16"
90
3 9 /16"
/4"
MD10ED. Module without call buttons, with

front plate in anodized aluminium, amplified
door speaker in two channels, and control of
volume of "receiver".
MD11ED. Module with 1 call button.
MD12ED. Module with 2 call buttons.
-10+40C
80%RH
Terminals
Y positive video signal output
F ground
X negative video signal output
H positive power supply input 21Vdc
Volume adjustment
To increase the volume from the amplifier in
the transmission mode, turn the trimmer
in a clockwise direction.
Sweeps
If necessary, you can manually change the camera framing by unloosening and adjusting the
horizontal or vertical screw in the desired direction
(or both screws if you want to adjust the image in
all directions).
PEP
PEP
Antilocale adjustment
In case of "feeback" (Larsen effect) in the
external unit it is necessary to operate as
follow:
- make the call from the door station and lift
the handset of an intercom;
- adjust the trimmer antilocale until the whistling stops (Larsen effect).
WITHOUT COAX
Testing and adjustments

Adjustments are carried out in the factory;
should any be necessary they can be readjusted from the outside with a screwdriver
with the trimmers identified by the words
antilocale and volume( ).
2 lux
291000
15625Hz
50/60Hz
3.6mm; F5
0,1m
Y
F
X
H
PEP
4.75.C091.01
213Vdc
0.3A
PEP
19
241D. Module with diodes for 2 users.

It allows for the use of the button modules
MD21, MD22, MD23, MD24, MD222, MD224,
MD226, MD228 in the 1+1 intercom systems
and 4+1 video intercom systems. It is applied
inside the button modules.
Technical data
Power supply
Operating current
Output of balanced video signal
Pixel number
Vertical frequency
Lens
Adjustable focus
Opening of auto-iris
SLIM
MD 40D. As above, without pan&tilt.

Terminals
A Supply 13VAC-70mA
- Ground
1 Reception-transmission; electric lock
release; call
S Electric lock
E Reception-transmission; electric lock release
P Call button
PUNTOVIRGOLA
1
2
3
4
5
6
7
/4"
MD 41D.
Camera module for 4+1 video systems without
coaxial cable, including:
- solid-state CCD camera, with auto iris, 3.6mm
fixed optics and 6 infrared LEDs;
- front plate in anodized aluminium with breakproof transparent screen;
- horizontal/vertical sweep.
PROJECT
90
Mody series .
To plan a 4+1 video intercom system all the
button modules can be used, as well as the
back boxes, the protective shelters and the
decorative shields which have been described
on pages 12 to 19. Only the CCD camera
MD41 and the modules MD10, MD11 and
MD12 are several, in that they have been
adapted for functioning with a reduced number of wires (ref. MD41D, MD10ED, MD11ED,
and MD12ED).
52
2 1 /16"
4 7 /8"
ERREP/R
124
3
PUSH-BUTTON PANELS
CAMERAS
The products of this line allow for the realization of a system with 4 common wires for all
monitors, and one for each user, without
using the coaxial cable.
It is possible to receive a call from any monitor, from the external station, it is possible to
see, communicate with the caller and release
the electric door lock.
horizontal
55
(9GB-2002)
WITH COAX
vertical
MODY
1 row push-button
MODY series push-button panel
ERREP/R
*
PROJECT
1 call button
2 call buttons
3 call buttons
4 call buttons
5 call buttons
6 call buttons
7 call buttons
PUNTOVIRGOLA
50
7 call buttons
8 call buttons
9 call buttons
10 call buttons
50
50
12 call buttons
14 call buttons
23 call buttons
24 call buttons
26 call buttons
11 call buttons
SLIM
16 call buttons
18 call buttons
50
50
19 call buttons
21 call buttons
50
27 call buttons
50
WITHOUT COAX
28 call buttons
30 call buttons
32 call buttons
34 call buttons
37 call buttons
38 call buttons
40 call buttons
42 call buttons
50
35 call buttons
50
WITH COAX
43 call buttons
50
45 call buttons
48 call buttons
56
(9GB-2002)
50 call buttons
1 row push-button
Composition board of Mody push-button panels.
MODY series push-button panel
MODY
Rain
shelter
1 MD72
1 MD82
1 MD92
1 MD72
1 MD82
1 MD92
ERREP/R
1 MD73
1 MD83
1 MD93
1 MD73
1 MD83
1 MD93
1 MD73
1 MD83
1 MD93
1 MD24
1 MD73
1 MD83
1 MD93
4 241D
1 MD24
1 MD23
2 MD72
1 MD84
1 MD94
PROJECT
4 241D
2 MD24
2 MD72
1 MD84
1 MD94
1 MD11ED
4 241D
2 MD24
2 MD72
1 MD84
1 MD94
1 MD41D
1 MD12ED
4 241D
2 MD24
2 MD72
1 MD84
1 MD94
11
1 MD41D
1 MD10ED
6 241D
2 MD24
1 MD23
2 MD73
1 MD86
1 MD96
12
1 MD41D
1 MD10ED
6 241D
3 MD24
2 MD73
1 MD86
1 MD96
13
1 MD41D
1 MD11ED
6 241D
3 MD24
2 MD73
1 MD86
1 MD96
14
1 MD41D
1 MD12ED
6 241D
3 MD24
2 MD73
1 MD86
1 MD96
15
1 MD41D
1 MD10ED
8 241D
3 MD24
1 MD23
2 MD73
1 MD86
1 MD96
PUNTOVIRGOLA
1 MD41D
1 MD10ED
8 241D
4 MD24
2 MD73
1 MD86
1 MD96
1 MD41D
1 MD11ED
8 241D
4 MD24
2 MD73
1 MD86
1 MD96
1 MD41D
1 MD12ED
8 241D
4 MD24
2 MD73
1 MD86
1 MD96
SLIM
19
1 MD41D
1 MD10ED
10 241D
4 MD24
1 MD23
2 MD74
1 MD808
1 MD908
20
1 MD41D
1 MD10ED
10 241D
5 MD24
2 MD74
1 MD808
1 MD908
21
1 MD41D
1 MD11ED
10 241D
5 MD24
2 MD74
1 MD808
1 MD908
22
1 MD41D
1 MD12ED
10 241D
5 MD24
2 MD74
1 MD808
1 MD908
23
1 MD41D
1 MD12ED
11 241D
5 MD24
1 MD21
2 MD74
1 MD808
1 MD908
1 MD41D
1 MD12ED
11 241D
5 MD24
1 MD22
2 MD74
1 MD808
1 MD908
1 MD41D
1 MD12ED
12 241D
5 MD24
1 MD23
2 MD74
1 MD808
1 MD908
1 MD41D
1 MD12ED
12 241D
6 MD24
2 MD74
1 MD808
1 MD908
1 MD41D
1 MD11ED
14 241D
5 MD24
2 MD23
3 MD73
1 MD89
1 MD99
1 MD41D
1 MD10ED
14 241D
7 MD24
3 MD73
1 MD89
1 MD99
1 MD41D
1 MD11ED
14 241D
7 MD24
3 MD73
1 MD89
1 MD99
30
1 MD41D
1 MD12ED
14 241D
7 MD24
3 MD73
1 MD89
1 MD99
31
1 MD41D
1 MD11ED
16 241D
6 MD24
2 MD23
3 MD74
1 MD812
1 MD912
32
1 MD41D
1 MD12ED
16 241D
6 MD24
2 MD23
3 MD74
1 MD812
1 MD912
33
1 MD41D
1 MD11ED
16 241D
8 MD24
3 MD74
1 MD812
1 MD912
34
1 MD41D
1 MD12ED
16 241D
8 MD24
3 MD74
1 MD812
1 MD912
35
1 MD41D
1 MD12ED
17 241D
8 MD24
1 MD21
3 MD74
1 MD812
1 MD912
36
1 MD41D
1 MD12ED
18 241D
8 MD24
2 MD21
3 MD74
1 MD812
1 MD912
1 MD41D
1 MD11ED
18 241D
8 MD24
2 MD22
3 MD74
1 MD812
1 MD912
1 MD41D
1 MD12ED
18 241D
8 MD24
2 MD22
3 MD74
1 MD812
1 MD912
39
1 MD41D
1 MD11ED
20 241D
8 MD24
2 MD23
3 MD74
1 MD812
1 MD912
40
1 MD41D
1 MD12ED
20 241D
8 MD24
2 MD23
3 MD74
1 MD812
1 MD912
41
1 MD41D
1 MD12ED
20 241D
9 MD24
1 MD23
3 MD74
1 MD812
1 MD912
42
1 MD41D
1 MD12ED
20 241D
10 MD24
3 MD74
1 MD812
1 MD912
43
1 MD41D
1 MD12ED
22 241D
8 MD24
3 MD23
4 MD74
44
1 MD41D
1 MD10ED
22 241D
11 MD24
4 MD74
45
1 MD41D
1 MD11ED
22 241D
11 MD24
4 MD74
46
1 MD41D
1 MD12ED
22 241D
11 MD24
4 MD74
47
1 MD41D
1 MD10ED
25 241D
11 MD24
3 MD21
4 MD74
1 MD41D
1 MD11ED
25 241D
11 MD24
3 MD21
4 MD74
1 MD41D
1 MD12ED
25 241D
11 MD24
3 MD21
4 MD74
1 MD41D
1 MD10ED
25 241D
11 MD24
3 MD22
4 MD74
Camera
module
Module with
speaker
2 diode
module
1 MD41D
1 MD11ED
1 MD41D
1 MD12ED
1 MD41D
1 MD10ED
2 241D
1 MD23
1 MD41D
1 MD10ED
2 241D
1 MD24
1 MD41D
1 MD11ED
2 241D
1 MD24
1 MD41D
1 MD12ED
2 241D
1 MD41D
1 MD10ED
1 MD41D
1 MD10ED
1 MD41D
1
2
10
Compositions and
dimensions
124x213x19
(47/8"x 83/8"x 3/4")
124x304.5x19
(4 7/8" x 12" x 3/4")
248x213x19
(9 /4" x 8 3/8" x 3/4")
3
16
17
18
248x304.5x19
(9 3/4" x 12" x 3/4")
24
25
26
248x395x19
(9 3/4" x 15 9/16" x 3/4")
27
28
29
37
38
50
496x395x19
(19 1/2" x 15 9/16" x 3/4")
or MD74 or MD804 or MD904
* or MD20 or MD50 or FC52P
57
(9GB-2002)
Optional
It replaces
MD72, 73, 74
WITH COAX
49
372x395x19
(14 5/8" x 15 9/16" x 3/4")
Back box and

module frame
48
372x304.5x19
(14 5/8" x 12" x 3/4")
Button and info or

blank modules
WITHOUT COAX
Hood
covers
N
calls
MODY
89
215.5
3 1/2"
8 1/2"
J2
ERREP/R
Monitors series Project
PROJECT
215
J3
8 7/16"
PUNTOVIRGOLA
Plugging in of monitor connectors to the terminal

boards of wall bracket.
SLIM
PT5111E. Two-colour flat monitor with two buttons, one for control
switch ON and one for door lock release, audio-video privacy, electronic
microphone, electronic modulated call note, terminal board for the
connection to the wall-bracket. It can be installed on the wall (with no builtin) by using the art.WB5111E.
PT5111EW. Colour: white.
WB5111E. Wall-bracket for the PT5111E and PT5111EW monitors.
It includes a terminal board for connection to the system.
Technical data
Power Supply
Operating current
Video tube
Television standard
Vertical frequency
Bandwidth
Balanced video signal
Starting up time
1824Vdc
0.35A
4" FLAT CRT
625 lines
15625Hz
50Hz
>5MHz
24 sec.
0+50C
90%RH
Terminals
H
Positive power supply input 1824Vdc-0.35A
F
Ground
X and Y
Video signal input
10
Call, audio reception/transmission,
door releasing
4
Control switch ON - button
WITHOUT COAX
83.5
3 5/16"
Installation of monitor onto the wall

bracket.
43
1 11/16"
U
P
40.5
1 5/ "
Dismounting of monitor from the wall

bracket.
Audio privacy
122
4 13/16"
1-2
140 150 cm
4" 7" 4" 11"
J1
1 2 3
X
Y
A1
F
F
H
10
4
WITH COAX
Measures for the installation of the wall

bracket WB5111E to the wall, and recommended height from the floor.
1 2 3
J1
2-3
1 2 3
aaaaaaaaaaaa
58
(9GB-2002)
1-2 = Monitor without audio privacy
J1
2-3 = Monitor with audio

privacy
MODY
PUNTOVIRGOLA
1181E. Timed supply for one monitor (or two

Flat monitors) CCD camera, electric lock and
push-button lights, etc.
Note
but all of its outputs are protected against overloading and short circuiting by temperature
sensors. To reset the power supply, pow-er
must be cut off for about one minute and can be
restored after having eliminated the defect.
- The power supply must be installed in a dry
place and can be fixed on DIN bar or on a wall
by using the expansion plugs.
89
3 1/2 "
A Output voltage 13Vac for:

-name plate light, exchangers and climatized
camera (continuous service 0.6A)
-electric door lock and bells (intermittent
service 1A)
- Ground for AC power supply
F Ground for DC power supply
H Continuous output 21Vdc-1A
(timed operation)
C- Electronic bell output for external calls 0.25A
4 Control switch-ON input from monitors
X Positive voltage output not stabilized 12Vcc0.2A
3+ Stabilized positive voltage output 8Vcc-0.1A
PROJECT
140
5 1/2 "
Terminals
74
2 15/16"
Technical data
Input voltage
127 or 230Vac
Frequency
50/60Hz
Power
48VA
Switch-ON time:
100 sec.
040C
Housing
DIN 8 modules A
Weight
0.95Kg.
ERREP/R
Power supply
SLIM
Module for supplementary call
65
2 9 /16"
70
89
2 3 /4"
3 1 /2"
RL37D.
When installed in 1+1 intercom and 4+1 video
intercom systems with electronic call, it provides a supplementary input for external calls,
enables supplementary video power supply
and provide a second ringer for floor calls.
Technical data
Power supply:
Stand-by current:
Max. switching current:
Housing:
Operating temperature:
Max. permissible humidity:
13Vac
40mA
1A (24V)
DIN 4 A modules
0 50C
90% RH
Terminals
A 13Vac alternate voltage input
ground
H timed positive continuous voltage input 21Vdc
IV supplementary power supply enabling
C common contact of relay
NA normally open contact of relay
NC normally closed contact of relay
1P electronic call input
1M electronic call output enabled from terminal
1P
CP electronic call output
Note: Remove the cover and move jumper J2 to

change the electronic ringer of CP and 1M outputs.
Position 1-2: modulated note
Position 2-3: continuous note
IV
H
A
CP
1P
1M
NC
NA
C
122
4 13/16"
25
1"
68
2 11/16"
to following distributors
to monitor
to monitor
X3 Y 3 H F
F H Y X
F H Y2 X2
X4 Y 4 H F
F H Y X
F H Y1 X1
Terminals
H
Input / output positive power supply
F
Ground
X and Y Input / output video signal
Note
The two 75 resistors, included with the product, must be applied to connectors Y-F and XF on the last distributor only.
Leave other terminals free.
59
(9GB-2002)
to monitor
to monitor
from previous distributors
WITH COAX
This unit allows video signal distribution for the

4+1 system without coaxial cable. They can be
wall mounted or recessed in a junction box.
212Vdc
60mA
2Vpp
0.8dB
>5MHz
DV2D. Distributor at 2 outputs.

DV4D. Distributor at 4 outputs.
Technical data
Power supply
Operating current
Max input video signal
Insertion loss
Bandwidth
WITHOUT COAX
Floor distributors
MODY
ERREP/R
Installation rules
PROJECT
*
- Cable channels of intercom and videointercom installations must be kept separate

from lighting or industrial systems as required by CEI Standards. Installations must
be realised according to the provisions of the law.
- A protective switched circuit-breaker must be provided before the power supply. Use
a single general switch in case of multiple power supplies (also for multiple entrances).
- Before connecting the power supply make sure that the rating complies with the
electrical mains.
- For electromagnetic compatibility reasons service modules must be installed near
their power supply.
PUNTOVIRGOLA
Wires
SLIM
1) You must select the correct type of cable to ensure the correct operation of
videointercom installations.
2) Wires must be dimensioned according to the distance between the devices and
according to their consumption.
3) Do not use multiple wires in parallel to reach the requested cross-section (for
example multipair telephone cables). Use a single wire with suitable cross-section.
In case of multicore cables use cables with low parasite parameters (low capacity
per metre, low inductance over Ohm).
4) If the installation includes additional power supplies, place them near the devices to
be powered.
Background noise
To avoid background noise over the voice line, it is recommended:
1) not to use the same cable channel for intercom cables and wires with AC loads;
2) to avoid using the same multicore cable for the transmission of voice signals and for
AC power supplies (lamps, amplified external stations, electrical locks). Always use
separate wires for AC power supplies;
3) for name plate lighting use a 12V additional transformer (PRS210 type) with suitable
capacity (consumption is 75mA for each lamp), keeping the 2 power supply wires
separate from the voice wires
4) the power supply must be positioned near the external door station in case of a long
distance between the external door station and the last videointercom.
Check that the connections of the system are carried out

correctly.
Put the system in use by connecting the power supply to
the mains.
By pushing a call button from the external push-button
panel, it activates the bell of the corresponding monitor
and it activates the system for a time of about 100
seconds. The images appear on the monitor a few
seconds after the call.
If in the meantime another call occurs, the monitor shuts
itself off and connects the last call. The system switches
off automatically after 100 sec.
In case more calls occur simultaneously, a protection
circuit against overloading and short circuiting is provided to disable the timer and therefore to shut off the
system.
In the absence of calls from the door station, from any
monitor (if provided in the system) it is possible to control
the entrance by pressing the
button (control switch
ON).
To work the electric door lock release press the
button from monitors.
In the two or more entrance systems all the audio and
video communications and door lock release, from one
entrance to the other, are automatically switched with the
call or the control switch ON.
In these systems the control switch ON from the monitors
can interrupt a running communication, for this reason it
is advisable to interrupt, by means of a relay, all the
control switches ON when the video system is active,
giving the priority of the communication to the door
stations.
Adjustments
All the regulations are carried out in the factory. For
possible corrections the intervention of a specialized
technician is advisable. The Contrast and Brightness
adjustments, being subject to the environmental lighting
conditions, are accessible from the under-neath by means
of a screw driver.
WIRE CROSS SECTION

Distance
Terminals
articles
WITHOUT COAX
Diagram 50m
lines
S mm
165 Ft
100m
330 Ft
200m
660 Ft
AWG
S mm
AWG
S mm
AWG
X-Y
0.35
22
0.35
22
0.35
22
10 - 4 - 1 - C-
0.5
20
0.75
18
16
F-H-A-S-
0.75
18
16
14
If the distance between the camera and the last videointercom is lower than 200 metres,
two 0.5mm (=0,5mm) wires can be used for video connection instead of coaxial
cable. A twisted pair must be used for 100m to 200m distances.
*
X
Y
X
Y
WITH COAX
60
(9GB-2002)
Interruption of the control switching ON in

multi-way systems with 2 or more audiovideo entrances.
To provide the service you must connect a relay art.1471
for each control switch ON function to be deactivated (or
art. 1472 for every 2 control switch ON).
Wire for control switch-ON from
monitor.
Si 411R/1
MODY
ERREP/R
ONE WAY VIDEO-INTERCOM SYSTEM
PROJECT
*
PUNTOVIRGOLA
*
SLIM
Application of 3 monitors and 1 parallel intercom
Application of 2 monitors and 1 parallel intercom
Application of 1 monitor and 3 parallel intercoms
Application of 1 monitor and 2 parallel intercoms
WITHOUT COAX
*
61
(9GB-2002)
WITH COAX
Note
In all the 4+1 video intercom systems it is possible to add further monitors and/or intercoms. To do this, insert the 2 application examples in this page instead
of the monitor which has been represented in the various installation systems of pages 61, 62, 63 and 64.
MODY

Si 41MR/2
ERREP/R
MULTI-WAY COMBINED INTERCOM AND VIDEO INTERCOM SYSTEM
PROJECT
*
PUNTOVIRGOLA
*
SLIM
Conversation privacy
In case of conversation privacy function, jumper
W1 of the intercom and resistance R1 of module SM50 must be cut.
WITHOUT COAX
*
WITH COAX
62
(9GB-2002)
Si 42MR/1
MODY
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH 2 AUTOMATICALLY SWITCHED VIDEO ENTRANCES,

ONE OF WHICH IS ONLY AUDIO.
2x
75W
X1
Y1
H
F
Xn
F
PROJECT
DV2D
DV4D
X
Y
H
F
10
4
PT5111E
WB5111E
PUNTOVIRGOLA
X1
Y1
H
F
X
Y
H
F
10
4
SLIM
DV2D
DV4D
Y
PT5111E
WB5111E
PRS210
1181E
X2
X2
X3
Xn
MD2..
P
MD2..
241D
C
E
P
C
MD7.
MD10ED
MD11ED
MD12ED
10b
P
C
E
1
2
9
3
5
6
10
10a
A
S
MD7.
MD10ED
MD11ED
MD12ED
A
S
1473
9b
8b
7b
SE (12Vac-1A max.)
F
H
X
Y
9a
8a
7a
63
(9GB-2002)
MD41D
WITH COAX
PA
(optional)
PA
(optional)
SE (12Vac-1A max.)
WITHOUT COAX
X3
230V
127V
0
230V
127V
0
Xn
MODY

Si 42MR/2
ERREP/R
MULTI-WAY VIDEO-INTERCOM SYSTEM WITH 2 AUTOMATICALLY SWITCHED VIDEO ENTRANCES.

2x
75W
PROJECT
DV2D
DV4D
Y
H
X1
Y1
H
F
X
Y
H
F
10
4
Xn
F
PT5111E
WB5111E
PUNTOVIRGOLA
SLIM
DV2D
DV4D
Y
H
X1
Y1
H
F
X
Y
H
F
10
4
PT5111E
WB5111E
PRS210
1181E
X3
230V
127V
0
230V
127V
0
WITHOUT COAX
Xn
X2
X2
X3
Xn
MD2..
P
MD2..
241D
C
E
P
C
MD7.
MD10ED
MD11ED
MD12ED
10b
1
2
9
3
5
6
10
P
C
E
1
10a
A
S
WITH COAX
PA
(optional)
PA
(optional)
1473
SE (12Vac-1A max.)
MD41D
F
H
X
Y
MD7.
MD10ED
MD11ED
MD12ED
A
S
9b
8b
7b
SE (12Vac-1A max.)
F
H
X
Y
9a
8a
7a
64
(9GB-2002)
MD41D
PRODUCT LIST
List of articles that can be used in videointercom installations with page reference.
VIDEOINTERCOMS WITH COAXIAL CABLE

Article
Description
Page ref.
Page ref.
PT5160MDW Videokit with PT5160W and intercommunicating module

PT5160W White Flat monitor Project series
PT5160W-LCD Colour Flat monitor Project series. White colour
PT5600MDW Videokit with PT5660W
PT5660W White monitor Project series
PT5800MDW Videokit with PT5860W
PT5860
Bicolour reflex monitor Project series
PT5860W White reflex monitor Project series
PV1200MD Videokit with PV1260
PV1260
Bicolour monitor PuntoVirgola series
PV1260MD Videokit with PV1260 and intercommunicating module
PV2100MD Videokit with PV2160
PV2160
Bicolour Flat monitor PuntoVirgola series
PV2160MD Videokit with PV2160 and intercommunicating module
PV2160W White Flat monitor Project series
R8
Push-button panel with 8 buttons ErreP/R series
R10
R12
R14
RP1
Push-button panel with 1 button ErreP/R series
RP2
RP4
RP6
RP8
RP10
RP12
RP100
Amplified door station with 1 push-button
RP200
Amplified door station with 2 push-buttons
SM50
Private conversation module for intercom
SR40
Electronic bell module for intercom
TA5160
Desk adapter for videointercom Project series
VM32
32-image video memory
WB1200 Wall bracket for PV1260 monitor
WB5100 Wall bracket for PT5160 monitor
WB5160 Wall bracket for PT5160 monitor
WB5600 Wall bracket for PT5660 and PT5860 monitors
WB5660 Wall bracket for PT5660 and PT5860 monitors
4+1 VIDEOINTERCOMS WITHOUT COAXIAL

241D
1181E
DV2D
DV4D
MD10ED
MD11ED
MD12ED
MD40D
MD41D
PT5111E
PT5111EW
RL37D
WB5111E
Diode module
Timed power supply
2-output video distributor
Amplified door station module without push-buttons
Amplified door station module with 1 push-button
Amplified door station module with 2 push-buttons
Camera module
Camera module
Bicolour Flat monitor Project series
White Flat monitor Project series
Module for supplementary calls
Wall bracket for PT5111E and PT5111EW monitors
31
2
2
31
31
4
31
6
31
6
31
10
31
31
8
31
8
21
21
21
21
21
21
21
21
21
21
21
21
21
34
11
3
25
10
10
8
8
2
2
4
4
55
55
59
59
59
55
55
55
55
55
58
58
59
58
WITH COAX
21
27
24
23
5
31
23
21
23
24
24
24
26
26
20
13
13
13
13
13
13
13
13
13
20
20
20
20
13
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
20
13
13
20
13
13
13
13
23
11
11
11
11
11
11
11
31
31
31
2
31
31
Description
WITHOUT COAX
337C
Electric door-speaker for ErreP/R push-button panel
476
1273TV
7-exchange switcher
1281
Video power supply
1283
Back-box for PT5660 and PV1260 monitors
1304
Videointercom cable with 10 wires + coaxial
1382
Audio-video timer
1385R
Camera unit ErreP/R series
1443E
Intercommunicanting module
1471
Relay unit
1473
4-exchange exchanger
2443
Audio-relay amplifier
DV2
DV4
FC52P
Access control keypad
MD10
Module for door speaker without push-buttons
MD11
Module for door speaker with 1 push-button
MD12
Module for door speaker with 2 push-buttons
MD20
Blank module
MD21
Button module with 1 push-button
MD22
Button module with 2 push-buttons
MD23
MD24
MD30
MD40
Camera module
MD40C
Colour camera module
MD41
Camera module
MD41C
Colour camera module
MD50
Street number module
MD71
Back box with frames for 1 module
MD72
Back box with frames for 2 modules
MD73
MD74
MD81
Hood cover for 1 module
MD82
Hood cover for 2 modules
MD83
Hood cover for 3 modules
MD84
Hood cover for 4 modules (2 frames with 2 modules)
MD804
Hood cover for 4 modules (1 frame with 4 modules)
MD86
MD808
MD89
MD812
MD91
Rain shelter for 1 module
MD92
Rain shelter for 2 modules
MD93
Rain shelter for 3 modules
MD94
Rain shelter for 4 modules (2 frames with 2 modules)
MD904
Rain shelter for 4 modules (1 frame with 4 modules)
MD96
MD908
MD99
MD912
MD100
Amplified door station with 1 push-button
MD122
Module for door speaker with 2 push-buttons, 2 row
MD124
Module for door speaker with 4 push-buttons, 2 row
MD200
Amplified door station with 2 push-buttons
MD222
Button module with 2 push-buttons, 2 row
MD224
MD226
MD228
PRS210
Transformer 13Vac - 15VA
PT510
Bicolour intercom Project series
PT510N
Beige intercom Project series
PT510W
White intercom Project series
PT520
Bicolour extendable intercom Project series
PT520N
Beige extendable intercom Project series
PT520W
White extendable intercom Project series
PT538
Desk adapter for intercom Project series
PT5100MD Videokit with PT5160 monitor
PT5100MDCW Colour videokit Project series
PT5100MDW Videokit with PT5160W monitor
PT5160
Bicolour Flat monitor Project series
PT5160MD Videokit with PT5160 and intercommunicating module
PT5160MDCW Colour videokit with intercommunicating module
Article
65
(9GB-2002)
English
ACI srl
Via Loretana, 134 - 60021 Camerano AN Italy.
Tel. (+39) 71959631 / 2. Fax. (+39) 7195150.

Catalogs (4+1)

Uploaded by

Copyright:

Available Formats

Catalogs (4+1)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogs (4+1)

Uploaded by

Copyright:

Available Formats

What is the purpose of the document?

What is the purpose of the document?

What equipment is necessary to properly install the systems?

What equipment is necessary to properly install the systems?

9

Notice to the installer and user

This edition contains helpful information on the operation and installation

In order to make the systems work perfectly it is necessary to install only

Packing materials (such as plastic bags, cardboard, polystyrene

European Mark of conformity to the

Mark of approval to German regulations.

Quality assured firm.

Installation diagrams WITH COAXIAL CABLE

One or multi-way diagrams

4+1 video-intercom system WITHOUT COAXIAL CABLE

Mody push-button panels

Wall-brackets for the PT5160, PT5160W and PT5160W-LCD monitors.

WB5100. The wall bracket includes a

PT5160W-LCD. Version with colour LCD screen

V Activation input for digital systems

Measures for the installation of the wall bracket

Note: This version is applied to all video

PT5160W. This model has the same features as

Taking out of button caps.

Inserting of extra buttons.

Installation of the wall bracket WB5100 or

Installation of monitor onto the wall bracket.

Dismounting of monitor from the wall bracket.

Installation of the wall bracket WB5100

Audio privacy or intercommunicating service

Position for the intercommunicating service.

Position for the audio privacy.

TA5160. Table adapter for monitors PT5160,

Installation of monitor to the table adapter.

Wall-brackets for the PT5660W monitor.

WB5600. The wall bracket includes a

Installation of wall bracket WB5600 or WB5660 to the back box 1283.

Plugging in of monitor connectors to the terminal boards of wall bracket.

Installation of monitor onto the wall bracket.

1283. Back-box for monitors PT5660W and

Supplementary push-buttons installation

Taking out of button caps.

Position for the audio privacy.

Position for the intercommunicating service.

Audio privacy or intercommunicating service

Wall-brackets for the PT5860 and PT5860W monitors.

WB5600. The wall bracket includes a

PT5860W. This model has the same features

Measures for the installation of the wall bracket

Installation of the wall bracket WB5600 or WB5660 to the

Plugging in of monitor connectors to the terminal boards of wall bracket.

Installation of monitor onto the wall

Supplementary push-buttons installation

Dismounting of monitor from the wall bracket.

Taking out of button caps.

Position for the audio privacy.

Position for the intercommunicating service.

Audio privacy or intercommunicating service