RKP4, RKP8 & RKP16 Keypads Installation Manual

THANK YOU FOR VOTING TEXECOM
INSTALLATION MANUAL
Remote Keypad
1. INSTALLATION
The Premier RKP4, RKP8 and RKP16 Remote Keypads are suitable for use with the following Texecom Control Panels: Premier 412, Premier 816 and Premier 832. Up to 6 keypads may be connected to the system.
1.1 Mounting
Open the keypad by carefully inserting a small flat-blade screwdriver into either half of the double slot at the base of the unit. Gently twist the screwdriver to ease the retaining clips. Do NOT use excessive force. The front and flap can now be removed. The PCB assembly is hinged for easy access. Alternatively the PCB assembly can be unclipped and completely removed if required. Mount the keypad using at least two appropriate countersunk screws (no larger than No. 6). A keyhole slot has been provided to assist mounting and aid levelling.
1.2 Selecting an Address

Each keypad MUST be given a different address using the DIP switch on the side of the PCB as follows:
Address 1 2 3 4 5 6 DIP 1 Off or On Off Off Off On Off DIP 2 Off On Off Off Off On DIP 3 Off Off On Off Off Off DIP 4 Off Off Off On On On
!"
2
NEVER set two RKPs to the same address. Keypads are factory set to address 1 (all switches off).
1.3 Wiring
It is strongly recommended that the system is completely powered down (mains and battery) before wiring a keypad. Connect the keypad to the control panel using 4-core cable as follows: INS161-2
Keypad + T R
Control Panel Data Bus + Data Bus Data Bus T Data Bus R
Up to six keypads may be connected in parallel (star) or series (daisy-chain) or any combination.
!"
When using long cable runs or connecting keypads in series (daisy-chain) ensure that the voltage at the keypad is no less than 10.0V. When using 6-core or 8-core cable always use the spare cores to double-up on 0V. This will allow longer cable runs particularly when connecting keypads in series (daisy-chain). As a rule trebling-up on 0V will be more beneficial than doubling-up on 12V and 0V.
Figure 1 - Cable Entry Cable entry MUST use either the top left-hand hole or the cable channel. NEVER run cables behind the PCB.
INS161-2
1.4 Programming
When the system is powered up it automatically checks and configures all connected keypads. It is strongly recommended that the system is completely powered down (mains and battery) before wiring a keypad.
1.5 Technical Specifications

Operating Voltage: Current Consumption: Zone Indicators: Status Indicators: Data Bus: Operating Temperature: Storage Temperature: Maximum Humidity: EMC Environment: Dimensions: Material: Packed Weight: 9 13.7VDC Nominal: 35mA; When fully back lit: 85mA Premier RKP4: 4; Premier RKP8: 8; Premier RKP16: 16 Alarm: Red; Trouble: Yellow; Armed: Red; Ready: Green 4-wire up to 250m Star, Daisy-Chain or any combination -10C to +45C -20C to +60C 95% non-condensing Residential/Commercial/Light Industrial or Industrial 140mm x 105mm x 35mm 3mm Polycarbonate 380g
1.6 Standards
Conforms to European Union (EU) Electro-Magnetic Compatibility (EMC) Directive 89/336/EEC (amended by 92/31/EEC and 93/68/EEC). The CE mark indicates that this product complies with the European requirements for safety, health, environmental and customer protection.
1.7 Warranty
All Texecom products are designed for reliable, trouble-free operation. Quality is carefully monitored by extensive computerised testing. As a result the Premier RKP is covered by a two year warranty against defects in material or workmanship (details on request). As the Premier RKP is not a complete alarm system but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Premier RKP failed to function correctly. Due to our policy of continuous improvement Texecom reserve the right to change specification without prior notice. Premier RKP is protected by UK and International Registered Design. Registered Design Number: 2047440. Premier is a trademark of Texecom. 4 INS161-2

RKP4, RKP8 & RKP16 Keypads Installation Manual

Uploaded by

Copyright:

Available Formats

RKP4, RKP8 & RKP16 Keypads Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RKP4, RKP8 & RKP16 Keypads Installation Manual

Uploaded by

Copyright:

Available Formats

THANK YOU FOR VOTING TEXECOM

1.2 Selecting an Address

1.5 Technical Specifications

You might also like