Asian Electron Co., Ltd.

6F-1, No.150, Jian Yi Road, Chung Ho City, Taipei Hsien, Taiwan

TEL: 886-2-8226-5158
FAX:886-2-82265150
http://www.asian-electron.com
e-mail: yukae@ms35.hinet.net

PSW700W / PSW1000W Series

Pure Sine Wave Inverter
Instruction Manual

List of Contents
1. Features
1-1
Application
1-2
Electrical performance
1-3
Mechanical drawings

2
3
5

2. Introduction
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8

6
7

Front panel operations

Rear panel operations
Installation
Quick hook up and testing
AC safety grounding
Making DC wiring connections
Inverter operation
Cooling fan working code

9
10
11
11
13
15

3. Maintenance

15

4. Troubleshooting guide

16

5. Warranty

17

6. Important safety striations

6-1
6-2

General safety precautions

Precautions when working with batteries

17
17

7. Appendices A
7-1
7-2

Dip switch (110V)

Dip switch (220V)

18
18

1.

Features
n
n
n
n
n
n
n

Pure sine wave output (THD < 3%) R Load

Output frequency : 50 / 60Hz switch
RS 232C interface / remote control port / wire connection to PC
Wired remote control
Compact size for convenient use and storage
Advanced microprocessor
Protection : Input low voltage
Overload
Short circuit
Low battery alarm
Input over voltage
Over temperature

1-1 Utilities Application

1-1-1 Power tools circular saws, drills, grinders, sanders, buffers, weed and hedge
trimmers, air compressors.
1-1-2 Office equipment computers, printers, monitors, facsimile machines, scanner.
1-1-3 Household items vacuum cleaners, fans, fluorescent and incandescent lights,
shavers, sewing machines.
1-1-4 Kitchen appliances microwave ovens, refrigerators and freezers, coffee makers,
blenders, ice makers, toasters.
1-1-5 Industrial equipment metal halide lamp, high pressure sodium lamp.
1-1-6 Home entertainment electronics television, VCRs, video games, stereos, musical
instruments, satellite equipment.

1-2 Electrical Performance700W

Specification

Model
YKPSW1270

Item

YKPSW2470

YKPSW4870

YKYKYKPSW1270E PSW2470E PSW4870E

Continuous Output Power

700W

Maximum Output Power

780W (3Min.)

Surge Rating

1400W

Input Voltage

12V

24V

48V

12V

24V

48V

Input Voltage Range

10-16VDC

20-32VDC

42-62VDC

10-16VDC

20-32VDC

42-62VDC

DC Input Over Voltage Alarm

15.5VDC

31.0VDC

61.0VDC

15.5VDC

31.0VDC

61.0VDC

DC Input Over Voltage Shut-down

16.0VDC

32.0VDC

62.0VDC

16.0VDC

32.0VDC

62.0VDC

DC Input Under Voltage Alarm

10.5VDC

21.0VDC

43.0VDC

10.5VDC

21.0VDC

43.0VDC

DC Input Under Voltage Shut-down

10.0VDC

20.0VDC

42.0VDC

10.0VDC

20.0VDC

42.0VDC

100/110/115/120V (Switch Selectable)

RMS3%

Output Voltage

200/220/230/240V (Switch Selectable)

RMS3%

50/60Hz 0.05% (Switch Selectable)

Frequency
Peak Output Current

13A

6A

Efficiency (full load)

88%

90%

91%

92%

93%

94%

No Load Current Draw

0.87A

0.43A

0.23A

0.83A

0.43A

0.22A

Power Saving function

Optional

Output Waveform

R Load Pure Sine Wave < 3% THD

Protection

Overload, Short circuit, Reverse Polarity (Fuse), Over/Under Input Voltage, Over Temp.

Safety

EN60950-1:2006 &

IEC60950-1: 2005(2nd Edition)

EN55022:1998/ A1:2000/A2:2003 (Class B)
EN55024: 1998/ A1:2001/A2:2003
EN61000-3-2: 2000/ A2:2005
EN61000-3-3: 1995/A1:2001
IEC61000-4-2:1995/ A1:1998/A2:2000

EMC

FCC Class B

IEC61000-4-3:2002/A1:2002
IEC61000-4-4:2004
IEC61000-4-5:1995/ A1:2000
IEC61000-4-6:1996/A1:2001
IEC61000-4-8:1993/A1:2000
IEC61000-4-11:2004

Digital Display

OVP, UVP, OTP, OLP, VAC, AMP, WATT, VDC, TEMP, Hz

Interface Control Port

RS-232C With Baud Rate 2400, 4800, 9600,19200 (Switch Selectable)

Remote Control Unit

Optional (Wire Control)

Operating Temperature Range

-20C to 50C

Storage Temperature Range

-30C to 70C

Cooling

Loading controlled cooling fan

Dimensions

298 (L) 179 (W) 81 (H) mm

Weight

2.8kgs
Note: The specifications are subject to change without notice.
3

Electrical Performance1000W
Specification

Model
YKPSW12100

Item

YKPSW24100

YKYKYKYKPSW48100 PSW12100E PSW24100E PSW48100E

Continuous Output Power

1000W

Maximum Output Power

1150W (3Min.)

Surge Rating

2000W

Input Voltage

12V

24V

48V

12V

24V

48V

Input Voltage Range

10-16VDC

20-32VDC

42-62VDC

10-16VDC

20-32VDC

42-62VDC

DC Input Over Voltage Alarm

15.5VDC

31.0VDC

61.0VDC

15.5VDC

31.0VDC

61.0VDC

DC Input Over Voltage

Shut-down

16.0VDC

32.0VDC

62.0VDC

16.0VDC

32.0VDC

62.0VDC

DC Input Under Voltage Alarm

10.5VDC

21.0VDC

43.0VDC

10.5VDC

21.0VDC

43.0VDC

DC Input Under Voltage

Shut-down

10.0VDC

20.0VDC

42.0VDC

10.0VDC

20.0VDC

42.0VDC

100/110/115/120V(Switch Selectable)
RMS3%

Output Voltage

200/220/230/240V(Switch Selectable)
RMS3%

50/60Hz 0.05% ( Switch Selectable)

Frequency
Peak Output Current

18A

9A

Efficiency (full load)

86%

88%

89%

87%

90%

92%

No Load Current Draw

1.07A

0.63A

0.43A

0.93A

0.47A

0.31A

Power Saving function

Optional

Output Waveform

R Load Pure Sine Wave < 3% THD

Protection

Overload, Short Circuit, Reverse Polarity (Fuse), Over/Under Input Voltage, Over Temp.

Safety

EN60950-1:2006 &

EMC

FCC Class B

IEC60950-1: 2005(2nd Edition)

EN55022:1998/ A1:2000/A2:2003 (Class B)
EN55024: 1998/ A1:2001/A2:2003
EN61000-3-2: 2000/ A2:2005
EN61000-3-3: 1995/A1:2001
IEC61000-4-2:1995/ A1:1998/A2:2000
IEC61000-4-3:2002/A1:2002
IEC61000-4-4:2004
IEC61000-4-5:1995/ A1:2000
IEC61000-4-6:1996/A1:2001
IEC61000-4-8:1993/A1:2000
IEC61000-4-11:2004

Digital Display

OVP, UVP, OTP, OLP, VAC, AMP, WATT, VDC, TEMP, Hz

Interface Control Port

RS-232C With Baud Rate 2400, 4800,9600,19200 (Switch Selectable)

Remote Control Unit

Optional (Wire Control)

Operating Temperature
Range

-20C to 50C

Storage Temperature Range

-30C to 70C

Cooling

Loading controlled cooling fan

Dimensions

334 (L) 179 (W) 81 (H) mm

Weight

3.8kgs
Note: The specifications are subject to change without notice.
4

1-3 Mechanical Drawings

700W & 1000W

2.

Introduction
The power inverter series are the member of the most advanced line of mobile AC power
systems available.
To get the most out of the power inverter, it must be installed and used properly.
Please read the instructions in this manual before installing and using this model.

2-1 Front Panel Operation

2-1-1 Front view:

2-1-2 ON / OFF switch:

Power ON / OFF switch, leave in the OFF position during installation.
2-1-3 Function key
When sequentially push Function Key, it will display various status on the function
screen, such as VAC, Amp, watts and so on.
When malfunction is occurred, its display will be flashed on the screen.

2-1-4 AC outlet (Outlet sockets available):

2-2 Rear Panel Operation:

2-2-1 Ventilation openings:

Do not obstruct. Allow at least 3 inch for airflow.
2-2-2 Battery terminals:
Connect to 12V / 24V / 48V battery or other 12V / 24V / 48V power source.
is positive;is negative. Reversing polarity connection will blow internal
fuse and may damage inverter permanently.

WARNING!
Do not connect the 12V model to a 24V battery. The unit will
be destroyed immediately.

2-2-3 RS-232
Connect to remote control unit (option accessory) or connect to computer to remote
control working status.

WARNING!
Any damages caused by using incorrect RS232 cable will be
outside of our warranty scope. If you are not sure which one
is correct RS232 cable, please purchase the correct RS232
cable from us directly.
8

2-2-4 Connect chassis ground terminal to earth or to vehicle chassis using # 8 AWG wire.

WARNING!
Operation of the inverter without a proper ground, connection
may result in an electrical safety hazard.

WARNING!
Shock Hazard. Before proceeding further, carefully check the
inverter is NOT connected to any batteries, and that all wiring
is disconnected from any electrical sources. Do not connect
the output terminals of the inverter to an incoming AC source.

2-3 Installation:
Where to install
The power inverter should be installed in a location that meets the following requirements.
2-3-1 Dry Do not allow water to drip or splash on the inverter.
2-3-2 Cool Ambient air temperature should be between -20C and 50C, the cooler the
better.
2-3-3 Safe Do not install in a battery compartment or other areas where flammable
fumes may exist, such as fuel storage areas or engine compartments.
2-3-4 Ventilated Allow at least 3 inch of clearance around the inverter for airflow. Ensure
the ventilation openings on the rear and bottom of the unit are not obstructed.
2-3-5 Dust-free Do not install the inverter in a dusty environments where are dust, wood
particles or other filings/shavings.
These dusts can be pulled into the unit when the cooling fan is operating.
2-3-6 Close to batteries Avoid excessive cable lengths but do not install the inverter in
the same compartment as batteries.
Use the recommended wire lengths and sizes (see section 2-6).
Also do not mount the inverter where it will be exposed to the gases produced by the
battery. These gases are very corrosive and prolonged exposure that will damage
the inverter.

2-4 Quick Hook Up and Testing:

2-4-1 Unpack and inspect the power inverter, check to see that the power switch in the
OFF position.
2-4-2 Connect the cables to the power input terminals on the rear panel of power inverter.
The red terminal is positive (+) and black terminal is negative (-).
Insert the cables into the terminals and tighten relative nut to clamp the wires
securely.

WARNING!
You may observe a spark when you make this connection
since current may flow to charge capacitors in the power
inverter.
Do not make this connection in the presence of flammable
fumes. Explosion or fire may result.

WARNING!
Make sure all the DC connections are tight (torque to 9-10
ft-lbs, 11.7-13Nm). Loose connections will overheat and could
result in a potential hazard.

2-4-3 Before proceeding further, carefully check that cable you have just connected
negative terminal of inverter to the negative output power source.
CAUTION!
Reverse polarity connection will blow a fuse in inverter and
may permanently damage the inverter.
Damage caused by reversing polarity connection is not
covered by our warranty.

2-4-4 Connect the cable from the negative terminal of the inverter to the negative terminal
of the power source. Make a secure connection.

WARNING!
You may observe a spark when you make this connection
since current may flow to charge capacitors in the power
inverter.
Do not make this connection in the presence of flammable
fumes. Explosion or fire may result.

10

2-4-5 Set the power switch to the ON position; you will hear the bi-bi-bi sound. At the
same time, the display shows the word ASIAN for two times. After that, you will
hear the continuous sound from internal alarm. Then, the AC voltage shows on the
display. It means the device has done the operation.
2-4-6 Set the power switch to the OFF position; the device shut down completely.
2-4-7 Please use a power meter to accurately measure the true output R.M.S. voltage of
inverter.
Our company uses a power meter such as IDRC CP-350 or ABM 2019 to measure
our product.
2-5 AC Safety Grounding:
During the AC wiring installation, AC input and output ground wires are connected to the
inverter. The AC input ground wire must connect to the incoming ground from your AC
utility source.
The AC output ground wire should go to the grounding point for your loads (for example, a
distribution panel of bus chassis).

WARNING!
Do not operate the power inverter without connecting it to
Ground.
Electrical shock hazard may result.

2-6 Making DC Wiring Connections:

Follow this procedure to connect the battery cables to the DC input terminals on the
inverter. Your cables should be as short as possible (ideally, less than 10 feet / 3 meters)
and large enough to handle the required current in accordance with the electrical codes or
regulations applicable to your installation.
Cables that are not an adequate gauge (too narrow) or are too long will cause decreased
inverter performance such as poor surge capability and frequent low input voltage
warnings and shutdowns.
These low input voltage warnings are due to DC voltage drop across the cables from the
inverter to the batteries.
The longer and narrower these cables, the greater the voltage drop.

WARNING!
The installation of a fuse must be on positive cable.
Failure to place a fuse on + cables running between the
inverter and battery may cause damage to the inverter and
will void warranty.
11

Increasing your DC cable size will help improve the situation.

Our company recommends the following cables for optimum inverter performance (apply
both 120V and 230V versions)
700W

Model No

Wire AWG

Inline Fuse

YK-PSW1270

#4

100A

YK-PSW1270E

#4

100A

YK-PSW2470

#6

50A

YK-PSW2470E

#6

50A

YK-PSW4870

#8

30A

YK-PSW4870E

#8

30A

Model No

Wire AWG

Inline Fuse

YK-PSW12100

#2

150A

YK-PSW12100E

#2

150A

YK-PSW24100

#4

80A

YK-PSW24100E

#4

80A

YK-PSW48100

#6

40A

YK-PSW48100E

#6

40A

1000W

Also, use only high quality copper wiring and keep cable length short from 3-6 feet.

700W & 1000W

12

2-7 Inverter Operation:

To operate the power inverter, turn it on using the ON/OFF switch on the front panel.
The power inverter is now ready to deliver AC power to your loads.
If you are operating several loads from the power inverter, turn them on separately after
the inverter has been turned on.
This will ensure that the power inverter does not have to deliver the starting currents for all
the loads at once.
2-7-1 Controls and indicators:
The ON / OFF switch turns the control circuit in the power inverter on and off.
The inverter operates from an input voltage range:
10.0 to 16.0 VDC for 12V models
20.0 to 32.0 VDC for 24V models
42.0 to 62.0 VDC for 48V models
The inverter will indicate high and low DC voltage conditions as follows:

Model
YK-PSW1270

YK-PSW12100

YK-PSW1270E YK-PSW12100E
YK-PSW2470

16.0VDC

15.5VDC

10.5VDC

10.0VDC

32.0VDC

31.0VDC

21.0VDC

20.0VDC

62.0VDC

61.0VDC

43.0VDC

42.0VDC

YK-PSW24100

YK-PSW2470E YK-PSW24100E
YK-PSW4870

DC Input Over
DC Input
DC Input
DC Input Over
Under Voltage Under Voltage
Voltage
Voltage Alarm
Shut-down
Alarm
Shut-down

YK-PSW48100

YK-PSW4870E YK-PSW48100E

2-7-2 Output Voltage indicator:

LED displays light on VAC as show as output voltage value
2-7-3 Output Current indicator
LED displays light on AMP as show as output current value
2-7-4 Output Watts indicator
LED displays light on Watts as show as output watts value
2-7-5 Input DC Voltage indicator
LED displays light on VDC as show as input DC voltage value
2-7-6 Temperature indicator
LED displays light on TEMP as show as internal operating temperature value
13

2-7-7

Output Frequency AC indicator

LED displays light on Hz as show as output frequency value.

Please have the accuracy of 6 functions of display, as below:

Functions

VAC

AMP

WATT

Ranges

100-120 200-240
VAC
VAC

0-10A

0-1KW

1% 0.5A

3%

Accuracy

1%

1%

VDC

TEMP

Frequency

10-16 20-32 42-62

0-120C 50Hz
VDC VDC VDC
2%

2%

2%

1%

60Hz

0.01 0.01

2-7-8

Over Voltage Protection indicator: (OVP)

The over voltage indicator indicates that the power inverter has shut itself down
because its input voltage exceeded 12V / 24V / 48VDC (Ref. point 2-7-1).

2-7-9

Under Voltage Protection indicator: (UVP)

The under voltage indicator indicates that the power inverter has shut itself down
because its input voltage fell below 12V / 24V / 48VDC (Ref. point 2-7-1).

2-7-10

Over Temp Protection indicator: (OTP)

The over temp indicator indicates that the power inverter has shut itself down
because its temperature has become overheated. The power inverter may
overheat because it has been operated at power levels above its rating, or
because it has been installed in a location which does not allow it to dissipate heat
properly. The power inverter will automatically back up, once it has cooled off.

14

2-7-11

Over Load Protection indicator: (OLP)

The overload indicator indicates that the power inverter has shut itself down.
When output voltage over its continuous voltage, then must return to operate
manually.

2-8 Cooling Fan Working Code:

Cooling fan of inverter is through detecting output power and over temperature situation to
work.
When start to turn on the inverter and output power under 300W, the cooling fan does not
start running. It complies with saving energy sources requirement. Until, output power is up
to 300W, the cooling fan will start to work in order to drop the inner temperature.
If the ventilation opening is obstructed, the inverter will enter over temperature protection
mode (OTP). The cooling fan will continue working to drop the inner temperature. When
the temperature comes down to normal situation, the inverter will turn on automatically.

3.

Maintenance:
Very little maintenance is required to keep your inverter operating properly.
You should clean the exterior of the unit periodically with a dry cloth to prevent
accumulation of dust and dirt. At the same time, tighten the screws on the DC input
terminals.

15

4.

Troubleshooting Guide:

WARNING!
Do not open or disassemble the inverter. Attempting to service
the unit yourself may result in a risk of electrical shock or fire.

Common problems television interference:

Operation of the power inverter can interfere with television reception on some channels, if
this situation occurs, the following steps may help to alleviate the problems.
l Make sure that the chassis ground lug on the back of the power inverter is solidly
connected to the ground system of your vehicle, boat or home.
l Do not operate high power loads with the power inverter while watching television.
l Make sure that the antenna feeding your television provides an adequate (snow
free) signal and that you are using good quality cable between the antenna and the
television.
l Move the television as far away from the power inverter as possible.
l Keep the cables between the battery and the power inverter as short as possible
and twist them together about 2 to 3 twists per foot. This mini radiated interference
from the cables.
Problem and Symptoms

Possible Cause

Solution

Low output voltage

(110V: 95-105VAC
220V: 190-210VAC)

Using average reading

voltmeter

Use true RMS reading meter

and cable. ( Ref. point 2-4-7).

Load display OLP flash

Over load

Reduce load

Low/High input voltage

Recharge battery,
check connections and cable.
( Ref. point 2-5 & point 2-6)

Thermal shutdown

Improve ventilation.
Make sure ventilation openings
in inverter are not obstructed.
Reduce ambient temperature.

Short circuit or wiring error

Very high power load

Check AC wiring for short

circuit or improper polarity. (hot
and neutral reversed)
Remove load.

No output voltage
Fault input voltage
No output voltage
Over temp indicator
Load less than 800W

No output voltage
Over load indicator

16

5.

Warranty:
We warrant this product against defects in materials and workmanship during warranty
period and will repair or replace any defective power inverter when directly returned
(postage paid) to us.
This warranty will be considered void if the unit has suffered any obvious damage by
natural and man-made factors, or alteration either internal or external and does not cover
damage arising from improper use such as plugging the unit into an unsuitable power
sources attempts to operate products with excessive power consumption requirement, or
use in unsuitable environments. This is the only warranty that the company makes.
No other warranties express or imply including warranties of merchantability and fitness for
a particular purpose. Repair and replacement are your sole remedies and the company
shall not be liable for damages, whether direct, incidental, special or consequential, even
though caused by negligence or other fault.

6.

Important Safety Instructions:

WARNING!
Before you install and use your inverter, be to read and save
these safety instructions.

6-1 General Safety Precautions

6-1-1 Do not expose the inverter to rain, snow, spray, bilge or dust. To reduce risk of
hazard, do not cover or obstruct the ventilation openings. Do not install the inverter
in a zero-clearance compartment. Overheating may result.
6-1-2 To avoid a risk of fire and electronic shock. Make sure that existing wiring is in good
electrical condition; and that wire size is not undersized. Do not operate the inverter
with damaged or substandard wiring.
6-2 Precautions When Working with Batteries
6-2-1 If battery acid contacts skin or clothing, wash immediately with soap and water. If
acid enters eye, immediately flood eye with running cold water for at lease 20
minutes and get medical attention immediately.
6-2-2 Never smoke or allow a spark or flame in vicinity of battery or engine
6-2-3 Do not drop a metal tool on the battery. The resulting spark or short-circuit on the
battery or other electrical part may cause an explosion.
6-2-4 Remove personal metal items such as rings, bracelets, necklaces, and watches
when working with a lead-acid battery.
A lead-acid battery produces a short-circuit current high enough to weld a ring or the
like to metal, causing a severe burn.
17

7.

Appendices A

7-1 110VAC Dip Switch (at the left side of inverter)

S1

FREQ. (Hz)

S2

S3

BAUD RATE

S4

S5

ON

60

OFF

OFF

2400

OFF

OFF

VOLTAGE OUTPUT
(VAC)
100

OFF

50

OFF

ON

4800

OFF

ON

110

-------

-------

ON
ON

OFF
ON

9600
19200

ON
ON

OFF
ON

115
120

S1 ( FREQ. Hz ) 50Hz/60Hz
S2 S3 (BAUD RATE ) 2400 / 4800 / 9600 / 19200
S4 S5 (VOLTAGE OUTPUT ) 100VAC / 110VAC / 115VAC / 120VAC
When you set up S1~S5, please reset the inverter and let update data through CPU.
7-2 220VAC Dip Switch (at the left side of inverter)
S1

FREQ. (Hz)

S2

S3

BAUD RATE

S4

S5

ON

60

OFF

OFF

2400

OFF

OFF

VOLTAGE OUTPUT
(VAC)
200

OFF

50

OFF

ON

4800

OFF

ON

220

-------

-------

ON
ON

OFF
ON

9600
19200

ON
ON

OFF
ON

230
240

S1 ( FREQ. Hz ) 50Hz/60Hz
S2 S3 (BAUD RATE ) 2400 / 4800 / 9600 / 19200
S4 S5 (VOLTAGE OUTPUT ) 200VAC / 220VAC / 230VAC / 240VAC
When you set up S1~S5, please reset the inverter and let update data through CPU.

RE-MARK:
The user manual is subject to change without notice.

18