Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
185 views

Project Title: Bachelor of Technology IN Mechanical Engineering

This document appears to be a student's dissertation submitted in partial fulfillment of the requirements for a Bachelor of Technology degree in Mechanical Engineering. It includes a title page with the student's name and roll number, as well as certificates signed by the student's faculty advisor. The dissertation also includes acknowledgments, an abstract, lists of tables and figures, and a table of contents outlining the organization of the chapters to follow, including an introduction, literature review and project selection chapter, methodology chapter, analysis chapter, and conclusion chapter. References are provided in alphabetical order at the end.

Uploaded by

Anonymous F0osiHu
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
185 views

Project Title: Bachelor of Technology IN Mechanical Engineering

This document appears to be a student's dissertation submitted in partial fulfillment of the requirements for a Bachelor of Technology degree in Mechanical Engineering. It includes a title page with the student's name and roll number, as well as certificates signed by the student's faculty advisor. The dissertation also includes acknowledgments, an abstract, lists of tables and figures, and a table of contents outlining the organization of the chapters to follow, including an introduction, literature review and project selection chapter, methodology chapter, analysis chapter, and conclusion chapter. References are provided in alphabetical order at the end.

Uploaded by

Anonymous F0osiHu
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 11

Project Title

A dissertation submitted in
Partial fulfillment of the requirements
for the awards of the degree

BACHELOR OF TECHNOLOGY
IN
MECHANICAL ENGINEERING
Submitted by
Student Name (Roll no wise)
Under the Guidance of
Faculty Name

DEPARTMENT OF MECHANICAL ENGINEERING


IMS ENGINEERING COLLEGE, GHAZIABAD
MAY, 2016

CERTIFICATE

This is to certify that the dissertation titled project title is a bonafide work by
student names, done under my guidance and supervision for partial fulfillment of the
requirement of degree of Bachelor of Technology in Mechanical Engineering. To
the best of my knowledge the work is original and has not been submitted at any other
Institute or University for the award of any other degree or diploma.

(FACULTY NAME)
Place:
Date:

Professor/Associate/Assistant Professor
Department of Mechanical Engineering
IMS Engineering College, Ghaziabad

ACKNOWLEDGEMENT

(Student Name)
ii

ABSTRACT

Key Words:

iii

LIST OF TABLES & FIGURES


1. List of Tables (if any)
No.
Example:
Table 3.1

Bill of Material & Costs


Chapter 3 and table 1.

2. Worksheets (if any)


Worksheet name and number
3. Figures & Exhibits
Example:
Figure 2.1
Exhibit 2.1

VE Savings Potential during the Life of a Typical System


Brief View of Sona Koyo

Page

TABLE OF CONTENTS
Contents

Page No.

CERTIFICATE

ACKNOWLEDGEMENT

ii

ABSTRACT

iii

LIST OF TABLES & FIGURES

iv-v

TABLE OF CONTENTS

vi-viii

ABBREVIATIONS

ix

CHAPTER 1:

INTRODUCTION

1.1

1.2

1.3

1.4

CHAPTER 2:

LITERATURE REVIEW & PROJECT SELECTION

2.1

2.2

2.3

10

2.4

11

2.5

12

17
CHAPTER 3:

METHODOLOGY

3.1

21

3.2

23

3.3

25

CHAPTER 4:
4.1

ANALYSIS
29

4.2
CHAPTER 9:

30
CONCLUSION AND RECOMMENDATION

REFERENCES
Example: (this should be alphabetic wise and site link should be at last)

ABBREVIATIONS
(if any)
DMM

Decision Making Matrix

FAST

Functional Analysis System Technique

Ix

REFRENCES

Ahmad, A., Aani, A., Alexis, Aanimina, A., Ahmad, A., (2009) Nonconventional machining of aluminium metal matrix composite. International
conference on Electrical Engineering, pp. 26 31.
Ahmad, C., (2005) Production and properties of in-situ aluminum, titanium
diboride composites formed by slag-metal reaction method, the degree of Master
of Science, in Metallurgical and Materials Engineering, Middle East Technical
University.
Jayakumar, K., Mathe, J., Joseph, M. A., (2013) An investigation of cutting
forces and toolwork interface temperature in milling of AlSiCp metal matrix
composite. Proceedings of the Institution of Mechanical Engineers, Part B: Journal
of Engineering Manufacture, 227:362-374

TYPING OF THE PROJECT REPORT:


Type of paper

Executive bone (white)

Paper size

A4 size

Font

Times new roman

Font size ( chapter title)

22 bold

Font size ( heading)

16 bold

Font size( sub heading)

14 bold

Font size ( body of the text)

12 normal

Font size (footnote)

10 normal

Margin

Left : 1 inch minimum


Right : 1 inch minimum
Top : 1 inch minimum
Bottom : 1 inch minimum

Text alignment

Justified

Cover sheet

Project report should be bound in black resin with


lettering in gold embossing / screen printing

Printing

One sided

Binding

Use perfect binding

STYLE OF WRITING:

Every chapter must begin on new page.

Page numbers are mandatory and should be given at the bottom (centre)

Spell checks should be carried out.

Diagrams and tables should be numbered as x.x (E.g. Fig. 3.1 for first figure in chapter
3) in the text of the discussion.

The length of the Report should be about 50 to 60 pages.

You might also like