FL - Glazing.agc Glass - Update 1 1

Copyright 2014 AIA
MasterSpec Premium
06/14
PRODUCT MASTERSPEC LICENSED BY ARCOM TO AGC GLASS COMPANY NORTH
AMERICA.
This Product MasterSpec Section is licensed by ARCOM to AGC Glass Company North America
("Licensee").
This Product MasterSpec Section modifies the original MasterSpec text, and does not include the
full content of the original MasterSpec Section.
Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by,
or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither AIA
nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec Section by
any end user. A qualified design professional should review and edit the document to suit project
requirements.
For more information, contact AGC Glass Company North America, 11175 Cicero Dr., Suite 400,
Alpharetta, GA 30022; Phone: (888) 234-8380; Website: www.us.agc.com; Email: info@us.agc.com.
For information about MasterSpec contact ARCOM at (800) 424-5080 or visit www.MasterSpec.com.
Copyright 2014 by The American Institute of Architects (AIA)
Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA
SECTION 088000 - GLAZING
TIPS:
To view non-printing Editor's Notes that provide guidance for editing, click on Masterworks/Single-File
Formatting/Toggle/Editor's Notes.
To read detailed research, technical information about products and materials, and coordination checklists,
click on Masterworks/Supporting Information.
Revise this Section by deleting and inserting text to meet Project-specific requirements.
This Section uses the term "Architect." Change this term to match that used to identify the design
professional as defined in the General and Supplementary Conditions.
Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section
titles may have changed.
PART 1 - GENERAL
SCHEDULE 0 - RELATED DOCUMENTS
Retain or delete this article in all Sections of Project Manual.
PRODUCT DATA SHEET 0 - Drawings and general provisions of the Contract, including General and
Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
GLAZING
088000 - 1
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
SCHEDULE 1 - SUMMARY
PRODUCT DATA SHEET 0 - Section includes:
0.1
0.2
Glass for [windows] [doors] [interior borrowed lites] [storefront framing] [glazed curtain
walls] [sloped glazing] [skylights].
Glazing sealants and accessories.
PRODUCT DATA SHEET 1 - Related Requirements:

Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this
Section but are specified in other Sections.
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Section 057300 "Decorative Metal Railings" for glazing in railings.

Section 084126 "All-Glass Entrances and Storefronts."
Section 084233 "Revolving Door Entrances" for glass in revolving door entrances.
Section 084423 "Structural-Sealant-Glazed Curtain Walls" for glazing sealants used in
structural-sealant-glazed curtain walls.
Section 088113 "Decorative Glass Glazing."
Section 088300 "Mirrors."
Section 088813 "Fire-Resistant Glazing."
Section 088853 "Security Glazing."
SCHEDULE 2 - DEFINITIONS
Retain terms that remain after this Section has been edited for a project.
PRODUCT DATA SHEET 0 - Glass Manufacturers: Firms that produce primary glass, as defined in
referenced glazing publications.
PRODUCT DATA SHEET 1 - Glass Fabricators: Firms that produce the fabricated glass products.
Fabrication processes include cutting, heat processing, insulating, spandrel, laminating and other as
fabrication activities defined in referenced glazing publications.
ASTM C 1036 also includes traditional thickness designations in IP units, but the actual thickness is
based on the equivalent IP designation in millimeters.
PRODUCT DATA SHEET 2 - Glass Thicknesses: Indicated by thickness designations in millimeters
according to ASTM C 1036.
PRODUCT DATA SHEET 3 - IBC: International Building Code.
PRODUCT DATA SHEET 4 - Interspace: Space between lites of an insulating-glass unit.
SCHEDULE 3 - COORDINATION
PRODUCT DATA SHEET 0 - Coordinate glazing channel dimensions to provide necessary bite on glass,
minimum edge and face clearances, and adequate sealant thicknesses, with reasonable tolerances.
GLAZING
088000 - 2
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
SCHEDULE 4 - PREINSTALLATION MEETINGS
Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex
enough to justify a conference.
PRODUCT DATA SHEET 0 - Preinstallation Conference: Conduct conference at [Project site] <Insert
location>.
If retaining subparagraphs below, revise to include Project-specific requirements. Insert additional
requirements to suit Project.
0.1
0.2
Review and finalize construction schedule and verify availability of materials, Installer's
personnel, equipment, and facilities needed to make progress and avoid delays.
Review temporary protection requirements for glazing during and after installation.
SCHEDULE 5 - ACTION SUBMITTALS

PRODUCT DATA SHEET 0 - Product Data: For each type of product.
PRODUCT DATA SHEET 1 - Sustainable Design Submittals:
"Product Data" Subparagraph below applies to LEED 2009 NC, CI, and CS; LEED v4; IgCC;
ASHRAE 189.1; and Green Globes. Coordinate with requirements for sealants.
1.1
Product Data: For sealants, indicating VOC content.
"Laboratory Test Reports" Subparagraph below applies to LEED 2009 for Schools, LEED v4, IgCC,
ASHRAE 189.1, and Green Globes. Coordinate with requirements for sealants.
1.2
Laboratory Test Reports: For sealants, indicating compliance with requirements for lowemitting materials.
PRODUCT DATA SHEET 2 - Glass Samples: For each type of [glass product other than clear
monolithic vision glass] [the following products]; 12 inches (300 mm) square.
2.1
2.2
2.3
2.4
Tinted glass.
Coated glass.
Laminated glass.
Insulating glass.
PRODUCT DATA SHEET 3 - Glazing Accessory Samples: For [sealants] [and] [colored spacers], in
12-inch (300-mm) lengths.[ Install sealant Samples between two strips of material representative in
color of the adjoining framing system.]
PRODUCT DATA SHEET 4 - Glazing Schedule: List glass types and thicknesses for each size opening
and location. Use same designations indicated on Drawings.
PRODUCT DATA SHEET 5 - Delegated-Design Submittal: For glass indicated to comply with
performance requirements and design criteria, including analysis data signed and sealed by the qualified
professional engineer responsible for their preparation.
GLAZING
088000 - 3
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
SCHEDULE 6 - INFORMATIONAL SUBMITTALS
Coordinate "Qualification Data" Paragraph below with qualification requirements in Section 014000
"Quality Requirements" and as may be supplemented in "Quality Assurance" Article. Retain second
option below only if retaining sputter-coated, low-E-coated, insulating-glass units in Part 2 and products
listed are those of an approved manufacturer or fabricator.
PRODUCT DATA SHEET 0 - Qualification Data: For [Installer] [manufacturers of insulating-glass
units with sputter-coated, low-E coatings] [glass testing agency] [and] [sealant testing agency].
Retain "Product Certificates" Paragraph below to require submittal of product certificates from
manufacturers.
PRODUCT DATA SHEET 1 - Product Certificates: For glass.
PRODUCT DATA SHEET 2 - Product Test Reports: For [tinted glass] [coated glass] [insulating glass]
[and] [glazing sealants], for tests performed by a qualified testing agency.
2.1
For glazing sealants, provide test reports based on testing current sealant formulations within
previous 36-month period.
PRODUCT DATA SHEET 3 - Preconstruction adhesion and compatibility test report.

PRODUCT DATA SHEET 4 - Sample Warranties: For special warranties.
SCHEDULE 7 - QUALITY ASSURANCE
Retain option in "Manufacturer Qualifications for Insulating-Glass Units with Sputter-Coated, Low-E
Coatings" Paragraph below only if products listed in Part 2 for sputter-coated, low-E-coated, insulatingglass units are those of an approved manufacturer.
PRODUCT DATA SHEET 0 - Fabricator Qualifications for Insulating-Glass Units with Sputter-Coated,
Low-E Coatings: A qualified insulating-glass fabricator who is approved by coated-glass manufacturer.
If retaining "Installer Qualifications" Paragraph below, verify, with prospective installers, that they can
comply with certification requirements referenced.
PRODUCT DATA SHEET 1 - Installer Qualifications: A qualified installer who employs glass installers
for this Project who are certified under the National Glass Association's Certified Glass Installer Program.
Retain "Glass Testing Agency Qualifications" Paragraph below if retaining "Product Test Reports"
Paragraph in "Informational Submittals" Article and it is known that glass products specified have been
tested by NFRC-accredited testing agencies.
PRODUCT DATA SHEET 2 - Glass Testing Agency Qualifications: A qualified independent testing
agency accredited according to the NFRC CAP 1 Certification Agency Program.
PRODUCT DATA SHEET 3 - Sealant Testing Agency Qualifications: An independent testing agency
qualified according to ASTM C 1021 to conduct the testing indicated.
GLAZING
088000 - 4
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 4 - Mockups: Build mockups to demonstrate aesthetic effects and to set
quality standards for materials and execution.
Retain first subparagraph below for large-scale mockup. Indicate portion of wall represented by mockup
on Drawings or draw mockup as separate element. Coordinate requirements with those in other Sections
specifying systems or products that receive glazing.
4.1
Install glazing in mockups specified in [Section 084113 "Aluminum-Framed Entrances and

Storefronts"] [Section 085113 "Aluminum Windows"] [Section 084413 "Glazed
Aluminum Curtain Walls"] <Insert Section number and title> to match glazing systems
required for Project, including glazing methods.
Retain subparagraph below if the intention is to make an exception to the default requirement in
Section 014000 "Quality Requirements" for demolishing and removing mockups.
4.2
Subject to compliance with requirements, approved mockups may become part of the completed
Work if undisturbed at time of Substantial Completion.
SCHEDULE 8 - PRECONSTRUCTION TESTING
Retain this article for preconstruction testing if insulating or laminated glass is installed with glazing
sealants. Adhesion and compatibility testing is essential for insulating and laminated glass and is usually
done by sealant manufacturer. Tests require large number of Samples, and some tests require four weeks
to complete.
PRODUCT DATA SHEET 0 - Preconstruction Adhesion and Compatibility Testing: Test each glass
product, tape sealant, gasket, glazing accessory, and glass-framing member for adhesion to and
compatibility with elastomeric glazing sealants.
Retain first subparagraph below if previous testing is acceptable.
0.1
0.2
0.3
0.4
0.5
Testing is not required if data are submitted based on previous testing of current sealant
products and glazing materials matching those submitted.
Use ASTM C 1087 to determine whether priming and other specific joint-preparation
techniques are required to obtain rapid, optimum adhesion of glazing sealants to glass, tape
sealants, gaskets, and glazing channel substrates.
Test no fewer than [eight] <Insert number> Samples of each type of material, including joint
substrates, shims, sealant backings, secondary seals, and miscellaneous materials.
Schedule enough time for testing and analyzing results to prevent delaying the Work.
For materials failing tests, submit sealant manufacturer's written instructions for corrective
measures including the use of specially formulated primers.
SCHEDULE 9 - DELIVERY, STORAGE, AND HANDLING

PRODUCT DATA SHEET 0 - Protect glazing materials according to manufacturer's written instructions.
Prevent damage to glass and glazing materials from condensation, temperature changes, direct exposure
to sun, or other causes.
GLAZING
088000 - 5
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Retain paragraph below if there is a reasonable possibility that insulating glass might be air freighted to
Project site or will otherwise be exposed to substantial altitude changes.
PRODUCT DATA SHEET 1 - Comply with insulating-glass manufacturer's written instructions for
venting and sealing units to avoid hermetic seal ruptures due to altitude change.
SCHEDULE 10 - FIELD CONDITIONS
PRODUCT DATA SHEET 0 - Environmental Limitations: Do not proceed with glazing when ambient
and substrate temperature conditions are outside limits permitted by glazing material manufacturers and
when glazing channel substrates are wet from rain, frost, condensation, or other causes.
Retain subparagraph below if sealants are required. Revise if another temperature range is required.
0.1
Do not install glazing sealants when ambient and substrate temperature conditions are outside
limits permitted by sealant manufacturer or are below 40 deg F (4.4 deg C).
SCHEDULE 11 - WARRANTY
When warranties are required, verify with Owner's counsel that warranties stated in this article are not
less than remedies available to Owner under prevailing local laws.
Paragraphs below are examples only.
PRODUCT DATA SHEET 0 - Manufacturer's Special Warranty for Coated-Glass Products: Manufacturer
agrees to replace coated-glass units that deteriorate within specified warranty period. Deterioration of
coated glass is defined as defects developed from normal use that are not attributed to glass breakage or to
maintaining and cleaning coated glass contrary to manufacturer's written instructions. Defects include
peeling, cracking, and other indications of deterioration in coating.
Verify available warranties and warranty periods. Revise subparagraph below if glass manufacturers insist
on warranty beginning on date of manufacture. See Evaluations.
0.1
Warranty Period: [10] <Insert number> years from date of Substantial Completion.
PRODUCT DATA SHEET 1 - Manufacturer's Special Warranty for Laminated Glass: Manufacturer
agrees to replace laminated-glass units that deteriorate within specified warranty period. Deterioration of
laminated glass is defined as defects developed from normal use that are not attributed to glass breakage
or to maintaining and cleaning laminated glass contrary to manufacturer's written instructions. Defects
include edge separation, delamination materially obstructing vision through glass, and blemishes
exceeding those allowed by referenced laminated-glass standard.
1.1
Warranty Period: Five years from date of Substantial Completion.
GLAZING
088000 - 6
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 2 - Manufacturer's Special Warranty for Insulating Glass: Manufacturer agrees
to replace insulating-glass units that deteriorate within specified warranty period. Deterioration of
insulating glass is defined as failure of hermetic seal under normal use that is not attributed to glass
breakage or to maintaining and cleaning insulating glass contrary to manufacturer's written instructions.
Evidence of failure is the obstruction of vision by dust, moisture, or film on interior surfaces of glass.
2.1
Warranty Period: [10] <Insert number> years from date of Substantial Completion.
Possibly insert glazier's warranty covering labor to replace insulating-glass units or, as an alternative, a
maintenance contract that incorporates unit prices for replacement labor.
PART 2 - PRODUCTS
See Editing Instruction No. 1 in the Evaluations for cautions about named manufacturers and products.
For an explanation of options and Contractor's product selection procedures, see Section 016000 "Product
Requirements."
SCHEDULE 0 - MANUFACTURERS
PRODUCT DATA SHEET 0 - Basis-of-Design Product: Subject to compliance with requirements,
provide AGC Glass Company North America; <product name or designation> or a comparable product
by one of the following:
0.1
AIG; American Insulated Glass.
0.2
Canadian Insulated Glass.
0.3
Columbia Commercial Products.
0.4
Cristacurva.
0.5
EFCO.
0.6
GTI; Glaz-Tech Industries.
0.7
Guardian Industries Corp.; SunGuard.
0.8
Insulite Glass, Inc.
0.9
JE Berkowitz, LP.
0.10
Laurier.
0.11
Manko.
0.12
Multiver.
0.13
Nashville Tempered Glass.
0.14
Niskayuna Glass.
0.15
Oldcastle BuildingEnvelope.
0.16
Pilkington North America.
0.17
PPG Industries, Inc.
0.18
ProTemp.
0.19
Redbud Glass.
0.20
SAAND.
0.21
SIGCO.
0.22
SolarSeal.
0.23
Tristar.
GLAZING
088000 - 7
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
0.24
0.25
0.26
Trulite Glass & Aluminum Solutions, LLC.

WA Wilson.
<Insert manufacturer's name>.
PRODUCT DATA SHEET 1 - Source Limitations for Glass: Obtain from single source from single
manufacturer for each glass type.
1.1
1.2
Obtain tinted glass from single source from single manufacturer.

Obtain reflective-coated glass from single source from single manufacturer.
PRODUCT DATA SHEET 2 - Source Limitations for Glazing Accessories: Obtain from single source
from single manufacturer for each product and installation method.
SCHEDULE 1 - PERFORMANCE REQUIREMENTS
PRODUCT DATA SHEET 0 - General: Installed glazing systems shall withstand normal thermal
movement and wind and impact loads (where applicable) without failure, including loss or glass breakage
attributable to the following: defective manufacture, fabrication, or installation; failure of sealants or
gaskets to remain watertight and airtight; deterioration of glazing materials; or other defects in
construction.
Retain "Delegated Design" Paragraph below if Contractor is required to assume responsibility for design.
PRODUCT DATA SHEET 1 - Delegated Design: Engage a qualified professional engineer, as defined in
Section 014000 "Quality Requirements," to design glazing.
PRODUCT DATA SHEET 2 - Structural Performance: Glazing shall withstand the following design loads
within limits and under conditions indicated determined according to the IBC and ASTM E 1300.
Retain one of two "Design Wind Pressures" subparagraphs below, usually first. The IBC requires that
design wind pressures used for design of exterior components and cladding not designed by the registered
design professional be shown on the Construction Documents.
2.1
2.2
Design Wind Pressures: As indicated on Drawings.

Design Wind Pressures: Determine design wind pressures applicable to Project according to
ASCE/SEI 7, based on heights above grade indicated on Drawings.
A.
Wind Design Data: As indicated on Drawings.
Retain "Wind Design Data" Subparagraph above or "Basic Wind Speed," "Importance Factor," and
"Exposure Category" subparagraphs below; insert other design data if required. The IBC requires that
data in subparagraphs below be shown on the Construction Documents.
B.
Basic Wind Speed: [85 mph (38 m/s)] [90 mph (40 m/s)] [100 mph (44 m/s)] [110 mph
(49 m/s)] <Insert value>.
C.
Importance Factor: [1.0] <Insert factor>.
D.
Exposure Category: [B] [C] [D].
GLAZING
088000 - 8
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Retain "Design Snow Loads" Subparagraph below if sloped glazing is exposed to snow loads. The IBC
requires that the flat-roof snow load be shown on the Construction Documents if the ground snow load
exceeds 10 lbf/sq. ft. (0.479 kN/sq. m).
2.3
2.4
Design Snow Loads: <Insert design snow load> [As indicated on Drawings].
Thickness of Patterned Glass: Base design of patterned glass on thickness at thinnest part of the
glass.
"Probability of Breakage for Sloped Glazing" Subparagraph below is an example only and is more
conservative than ASTM E 1300 and the IBC, which are based on a probability of breakage of 0.008.
2.5
Probability of Breakage for Sloped Glazing: For glass surfaces sloped more than 15 degrees
from vertical, design glass for a probability of breakage not greater than 0.001.
Deflection requirements in "Maximum Lateral Deflection" Subparagraph below are examples only and
apply only to glass supported on all four edges. The IBC does not contain any deflection limits for glass.
ASTM E 1300 only requires that the deflection not result in loss of edge support. Revise to suit Project.
2.6
Maximum Lateral Deflection: For glass supported on all four edges, limit center-of-glass
deflection at design wind pressure to not more than 1/50 times the short-side length or 1 inch
(25 mm), whichever is less.
"Differential Shading" Subparagraph below applies primarily to tinted glass because of its heat-absorbing
property. ASTM E 1300 and the IBC do not address this concern.
2.7
Differential Shading: Design glass to resist thermal stresses induced by differential shading
within individual glass lites.
Retain "Windborne-Debris-Impact Resistance" Paragraph below if required by Project. The IBC defines
windborne debris regions. Enhanced protection applies to essential facilities. Verify requirements of
authorities having jurisdiction.
PRODUCT DATA SHEET 3 - Windborne-Debris-Impact Resistance: Exterior glazing shall comply with
[basic] [enhanced]-protection testing requirements in ASTM E 1996 for [Wind Zone 1] [Wind Zone 2]
[Wind Zone 3] [Wind Zone 4] when tested according to ASTM E 1886. Test specimens shall be no
smaller in width and length than glazing indicated for use on Project and shall be installed in same
manner as glazing indicated for use on Project.
3.1
3.2
Large-Missile Test: For glazing located within 30 feet (9.1 m) of grade.

Small-Missile Test: For glazing located more than 30 feet (9.1 m) above grade.
PRODUCT DATA SHEET 4 - Safety Glazing: Where safety glazing is indicated, provide glazing that
complies with 16 CFR 1201, Category II.
PRODUCT DATA SHEET 5 - Thermal and Optical Performance Properties: Provide glass with
performance properties specified, as indicated in manufacturer's published test data, based on procedures
indicated below:
Retain subparagraphs below that apply to types of glass for which thermal and optical performance
properties are specified.
5.1
For monolithic-glass lites, properties are based on units with lites [6 mm thick] [of thickness
indicated].
GLAZING
088000 - 9
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
5.2
5.3
5.4
5.5
5.6
For laminated-glass lites, properties are based on products of construction indicated.

For insulating-glass units, properties are based on units of thickness indicated for overall unit
and for each lite.
U-Factors: Center-of-glazing values, according to NFRC 100 and based on LBL's
WINDOW 5.2 computer program, expressed as Btu/sq. ft. x h x deg F (W/sq. m x K).
Solar Heat-Gain Coefficient and Visible Transmittance: Center-of-glazing values, according to
NFRC 200 and based on LBNL's WINDOW 6.3 computer program.
Visible Reflectance: Center-of-glazing values, according to NFRC 300.
SCHEDULE 2 - GLASS PRODUCTS, GENERAL

PRODUCT DATA SHEET 0 - Glazing Publications: Comply with published recommendations of glass
product manufacturers and organizations below unless more stringent requirements are indicated. See
these publications for glazing terms not otherwise defined in this Section or in referenced standards.
Retain publications in subparagraphs below that apply to glass products specified.
0.1
0.2
0.3
0.4
GANA Publications: ["Laminated Glazing Reference Manual" and ]"Glazing Manual."

AAMA Publications: AAMA GDSG-1, "Glass Design for Sloped Glazing," and
AAMA TIR A7, "Sloped Glazing Guidelines."
IGMA Publication for Sloped Glazing: IGMA TB-3001, "Guidelines for Sloped Glazing."
IGMA Publication for Insulating Glass: SIGMA TM-3000, "North American Glazing
Guidelines for Sealed Insulating Glass Units for Commercial and Residential Use."
Retain "Safety Glazing Labeling" Paragraph below if applicable and if labeling is required. Not all
manufacturers participate in third-party testing programs.
PRODUCT DATA SHEET 1 - Safety Glazing Labeling: Where safety glazing is indicated, permanently
mark glazing with certification label of [the SGCC] [the SGCC or another certification agency
acceptable to authorities having jurisdiction] [or] [manufacturer]. Label shall indicate manufacturer's
name, type of glass, thickness, and safety glazing standard with which glass complies.
Delete "Insulating-Glass Certification Program" Paragraph below if no insulating glass. Not all
manufacturers participate in program; see the IGCC directory for participants. Verify that types of units
required are certified.
PRODUCT DATA SHEET 2 - Insulating-Glass Certification Program: Permanently marked either on
spacers or on at least one component lite of units with appropriate certification label of IGCC.
PRODUCT DATA SHEET 3 - Thickness: Where glass thickness is indicated, it is a minimum.[ Provide
glass that complies with performance requirements and is not less than the thickness indicated.]
Delete "Minimum Glass Thickness for Exterior Lites" Subparagraph below if glass thickness for each
kind of glass is indicated on Drawings or in Part 2 articles where glass units are specified.
3.1
Minimum Glass Thickness for Exterior Lites: [6 mm] <Insert thickness designation>.
Revise "Thickness of Tinted Glass" Subparagraph below if different thicknesses of tinted glass are
required for specific locations. Different thicknesses of tinted glass have different appearances.
GLAZING
088000 - 10
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
3.2
Thickness of Tinted Glass: Provide same thickness for each tint color indicated throughout
Project.
PRODUCT DATA SHEET 4 - Strength: Where annealed float glass is indicated, provide annealed float
glass, heat-strengthened float glass, or fully tempered float glass[ as needed to comply with
"Performance Requirements" Article]. Where heat-strengthened float glass is indicated, provide heatstrengthened float glass or fully tempered float glass[ as needed to comply with "Performance
Requirements" Article]. Where fully tempered float glass is indicated, provide fully tempered float
glass.
PRODUCT DATA SHEET 5 - Heat-Treated Float Glass: Where heat treated float glass is required
or indicated provide glass in accordance to ASTM C 1048; ASTM C 1036 Type I; Quality-Q3;
Class I (clear) unless otherwise indicated; of kind and condition indicated.
Retain first subparagraph below if orientation of glass is important. See Evaluations. Verify that glass
sizes indicated can be manufactured with roll wave parallel to bottom edge.
5.1
5.2
5.3
Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to

bottom edge of glass as installed unless otherwise indicated.
For uncoated glass, comply with requirements for Condition A.
For coated vision glass, comply with requirements for Condition C (other coated glass).
If heat soaking of fully tempered glass is needed, insert requirements here.

PRODUCT DATA SHEET 6 - Coating in first paragraph below is available only on clear float glass and
is applied pyrolytically on the float line. Consequently, if a reflective or low-E coating is required (which
would be on the second surface, which was exposed to the molten tin bath on the float line), it must be a
sputtered coating.
SCHEDULE 3 - GLASS PRODUCTS
Retain paragraphs in this article that apply to monolithic-, laminated-, and insulating-glass types
specified.
Retain "Clear Annealed Float Glass" Paragraph below even if plain, clear float glass is not required; other
paragraphs in this article and in glass types articles depend on below for definition of "clear float glass."
PRODUCT DATA SHEET 0 - Clear Annealed Float Glass: ASTM C 1036, Type I, Class 1 (clear),
Quality-Q3.
Retain option in "Ultraclear Float Glass" Paragraph below if required for passive solar design.
PRODUCT DATA SHEET 1 - Ultraclear Float Glass: ASTM C 1036, Type I, Class I (clear), Quality-Q3;
and with visible light transmission of not less than 91 percent[ and solar heat gain coefficient of not less
than 0.87].
PRODUCT DATA SHEET 2 - Tinted Annealed Float Glass: ASTM C 1036, Type I, Class 2 (tinted),
Quality-Q3.
GLAZING
088000 - 11
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Retain "Fully Tempered Float Glass" Paragraph below even if plain, tempered float glass is not required;
other paragraphs in this article and glass types articles depend on below for definition of "fully tempered
float glass." Always retain paragraph if Contractor is responsible for determining glass thickness and
strength.
PRODUCT DATA SHEET 3 - Fully Tempered Float Glass: ASTM C 1048, Kind FT (fully tempered),
Condition A (uncoated) unless otherwise indicated, Type I, Class 1 (clear) or Class 2 (tinted) as indicated,
Quality-Q3.
Retain "Fabrication Process" Subparagraph below if orientation of glass is important. See Evaluations.
Verify that glass sizes indicated can be manufactured with roll wave parallel to bottom edge.
3.1

If heat soaking of fully tempered glass is needed, insert requirements here.

Retain "Heat-Strengthened Float Glass" Paragraph below even if plain, heat-strengthened float glass is
not required but other paragraphs in this article and glass types articles depend on below for definition of
"heat-strengthened float glass." Always retain paragraph if Contractor is responsible for determining glass
thickness and strength.
PRODUCT DATA SHEET 4 - Heat-Strengthened Float Glass: ASTM C 1048, Kind HS (heat
strengthened), Type I, Condition A (uncoated) unless otherwise indicated, Type I, Class 1 (clear) or
Class 2 (tinted) as indicated, Quality-Q3.
Retain "Fabrication Process" Subparagraph below if orientation of glass is important. See Evaluations.
Verify that glass sizes indicated can be manufactured with roll wave parallel to bottom edge.
4.1

PRODUCT DATA SHEET 5 - Sputtered Coated Low-Emissivity Clear Vision Glass,
ASTM C 1376, Kind CV (coated vision glass), coated by sputtered process, ASTM C 1036,
Type I, Class I (clear) or Class 2 (tinted) as indicated, Quality-Q3.
PRODUCT DATA SHEET 6 - Pyrolytic Coated Low-Emissivity Clear Vision Glass,
ASTM C 1376, Kind CO (coated overhead glass), coated by pyrolytic process, ASTM C 1036,
Type I, Class I (clear) or Class 2 as indicated, Quality-Q3.
PRODUCT DATA SHEET 7 - Ceramic-Coated Vision Glass: ASTM C 1048, Condition C, Type I, Class 1
(clear) or Class 2 (tinted) as indicated, Quality-Q3; and complying with Specification No. 95-1-31 in
GANA's "Engineering Standards Manual."
PRODUCT DATA SHEET 8 - Reflective-Coated Vision Glass: ASTM C 1376.
PRODUCT DATA SHEET 9 - Ceramic-Coated Spandrel Glass: ASTM C 1048, Type I, Condition B,
Quality-Q3.
GLAZING
088000 - 12
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
In "Silicone-Coated Spandrel Glass" Paragraph below, coating is an elastomeric paint and is less
expensive than ceramic coating. Silicone coating is typically more uneven than ceramic coating and
frequently contains pin holes; however, these irregularities are generally not visible from typical viewing
distances because of lack of illumination in the space behind spandrel glass. Silicone coating is more
readily available in custom colors and may provide fallout resistance.
PRODUCT DATA SHEET 10 - Silicone-Coated Spandrel Glass: ASTM C 1048, Type I, Condition C,
Quality-Q3.
PRODUCT DATA SHEET 11 - Reflective-Coated Spandrel Glass: ASTM C 1376, Kind CS.
SCHEDULE 4 - LAMINATED GLASS
AGC Glass Company North America's Defender Impact laminated glass, with 0.060 or 0.090 interlayers,
provides small and large missile protection and is typically specified in section 088853 "Security
Glazing".
PRODUCT DATA SHEET 0 - Laminated Glass: ASTM C 1172. Use materials that have a proven record
of no tendency to bubble, discolor, or lose physical and mechanical properties after fabrication and
installation.
0.1
0.2
0.3
Construction: Laminate glass with [polyvinyl butyral interlayer] [ionoplast interlayer] [or]
[cast-in-place and ultra-violet cured-transparent-resin interlayer] to comply with interlayer
manufacturer's written instructions.
Interlayer Thickness: Provide thickness not less than that indicated and as needed to comply
with requirements.
Interlayer Color: Clear unless otherwise indicated.
Retain "Windborne-Debris-Impact-Resistant Laminated Glass" Paragraph below if retaining "WindborneDebris-Impact Resistance" Paragraph in "Performance Requirements" Article.
PRODUCT DATA SHEET 1 - Windborne-Debris-Impact-Resistant Laminated Glass: Comply with
requirements specified above for laminated glass except laminate glass with[ one of] the following to
comply with interlayer manufacturer's written instructions:
1.1
1.2
1.3
1.4
1.5
Polyvinyl butyral interlayer.

Polyvinyl butyral interlayers reinforced with polyethylene terephthalate film.
Ionomeric polymer interlayer.
Cast-in-place and cured-transparent-resin interlayer.
Cast-in-place and cured-transparent-resin interlayer reinforced with polyethylene terephthalate
film.
SCHEDULE 5 - INSULATING GLASS

PRODUCT DATA SHEET 0 - Insulating-Glass Units: Factory-assembled units consisting of sealed lites
of glass separated by a dehydrated interspace, qualified according to ASTM E 2190.
GLAZING
088000 - 13
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Retain one of five options in "Sealing System" Subparagraph below, or insert other combinations;
coordinate with manufacturers and products.
0.1
Sealing System: Dual seal, with [manufacturer's standard] [polyisobutylene and

polysulfide] [polyisobutylene and silicone] [polyisobutylene and hot-melt butyl]
[polyisobutylene and polyurethane] <Insert description> primary and secondary sealants.
If retaining a specific spacer material, coordinate with manufacturers and products.

0.2
Spacer: [Manufacturer's standard spacer material and construction] [Aluminum with mill
or clear anodic finish] [Aluminum with black, color anodic finish] [Aluminum with
bronze, color anodic finish] [Aluminum with powdered metal paint finish in color selected
by Architect] [Galvanized steel] [Stainless steel] [Polypropylene-covered stainless steel in
color selected by Architect] [Thermally broken aluminum] [Nonmetallic laminate]
[Nonmetallic tube] <Insert material>.
Revise "Desiccant" Subparagraph below if a specific type of desiccant is required.
0.3
Desiccant: Molecular sieve or silica gel, or a blend of both.
SCHEDULE 6 - GLAZING SEALANTS
PRODUCT DATA SHEET 0 - General:
0.1
0.2
Compatibility: Compatible with one another and with other materials they contact, including
glass products, seals of insulating-glass units, and glazing channel substrates, under conditions
of service and application, as demonstrated by sealant manufacturer based on testing and field
experience.
Suitability: Comply with sealant and glass manufacturers' written instructions for selecting
glazing sealants suitable for applications indicated and for conditions existing at time of
installation.
Subparagraph below applies to LEED 2009 NC, CI, and CS; LEED v4; IgCC; ASHRAE 189.1; and
Green Globes.
0.3
Sealant shall have a VOC content of 250 g/L or less.
Subparagraph below applies to LEED 2009 for Schools Credit IEQ 4.1.
0.4
Sealant shall comply with the testing and product requirements of the California Department of
Public Health's "Standard Method for the Testing and Evaluation of Volatile Organic Chemical
Emissions from Indoor Sources Using Environmental Chambers."
0.5
Colors of Exposed Glazing Sealants: [As indicated by manufacturer's designations] [Match
Architect's samples] [As selected by Architect from manufacturer's full range].
Retain one or more of four "Glazing Sealant" paragraphs below. If retaining more than one, retain
"Applications" subparagraphs.
PRODUCT DATA SHEET 1 - Glazing Sealant: Neutral-curing silicone glazing sealant complying with
ASTM C 920, Type S, Grade NS, Class 100/50, Use NT.
1.1
Manufacturers: Subject to compliance with requirements, provide products by one of the

following:
GLAZING
088000 - 14
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
A.
B.
C.
D.
E.
F.
G.
1.2
Dow Corning Corporation.

GE Construction Sealants; Momentive Performance Materials Inc.
May National Associates, Inc.; a subsidiary of Sika Corporation.
Pecora Corporation.
Sika Corporation.
Tremco Incorporated.
Applications: <Describe types of glazing applications where this sealant is required>.
ASTM C 920, Type S, Grade NS, Class 50, Use NT.
2.1

following:
A.
B.
C.
D.
E.
F.
G.
H.
I.
2.2
BASF Corporation-Construction Systems.

Pecora Corporation.
Polymeric Systems, Inc.
Sika Corporation.
3.1

following:
A.
B.
C.
D.
E.
F.
G.
H.
I.
3.2
Bostik, Inc.
Schnee-Morehead, Inc., an ITW company.
Sika Corporation.
PRODUCT DATA SHEET 4 - Glazing Sealant: Acid-curing silicone glazing sealant complying with
GLAZING
088000 - 15
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
4.1

following:
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
4.2
BASF Corporation-Construction Systems.

Bostik, Inc.
Pecora Corporation.
Schnee-Morehead, Inc., an ITW company.
Sika Corporation.
SCHEDULE 7 - GLAZING TAPES

PRODUCT DATA SHEET 0 - Back-Bedding Mastic Glazing Tapes: Preformed, butyl-based, 100 percent
solids elastomeric tape; nonstaining and nonmigrating in contact with nonporous surfaces; with or without
spacer rod as recommended in writing by tape and glass manufacturers for application indicated; and
complying with ASTM C 1281 and AAMA 800 for products indicated below:
Retain one or more back-bedding tapes from subparagraphs below. AAMA 804.3 tape is for less-severe
back-bedding and drop-in, residential and light-commercial glazing applications. AAMA 806.3 tape is for
high-performance commercial glazing applications involving continuous pressure from gaskets or
pressure-generating stop designs. AAMA 807.3 tape is for commercial glazing applications not involving
continuous pressure from gaskets and stop designs.
0.1
0.2
0.3
AAMA 804.3 tape, where indicated.

AAMA 806.3 tape, for glazing applications in which tape is subject to continuous pressure.
AAMA 807.3 tape, for glazing applications in which tape is not subject to continuous pressure.
PRODUCT DATA SHEET 1 - Expanded Cellular Glazing Tapes: Closed-cell, PVC foam tapes; factory
coated with adhesive on both surfaces; and complying with AAMA 800 for the following types:
1.1
1.2
AAMA 810.1, Type 1, for glazing applications in which tape acts as the primary sealant.
AAMA 810.1, Type 2, for glazing applications in which tape is used in combination with a full
bead of liquid sealant.
SCHEDULE 8 - MISCELLANEOUS GLAZING MATERIALS

PRODUCT DATA SHEET 0 - General: Provide products of material, size, and shape complying with
referenced glazing standard, with requirements of manufacturers of glass and other glazing materials for
application indicated, and with a proven record of compatibility with surfaces contacted in installation.
GLAZING
088000 - 16
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 1 - Cleaners, Primers, and Sealers: Types recommended by sealant or gasket
manufacturer.
PRODUCT DATA SHEET 2 - Setting Blocks: Elastomeric material with a Shore, Type A durometer
hardness of 85, plus or minus 5.
PRODUCT DATA SHEET 3 - Spacers: Elastomeric blocks or continuous extrusions of hardness required
by glass manufacturer to maintain glass lites in place for installation indicated.
PRODUCT DATA SHEET 4 - Edge Blocks: Elastomeric material of hardness needed to limit glass lateral
movement (side walking).
Retain "Cylindrical Glazing Sealant Backing" Paragraph below if applicable for glazing channels.
PRODUCT DATA SHEET 5 - Cylindrical Glazing Sealant Backing: ASTM C 1330, Type O (open-cell
material), of size and density to control glazing sealant depth and otherwise produce optimum glazing
sealant performance.
SCHEDULE 9 - FABRICATION OF GLAZING UNITS
PRODUCT DATA SHEET 0 - Fabricate glazing units in sizes required to fit openings indicated for
Project, with edge and face clearances, edge and surface conditions, and bite complying with written
instructions of product manufacturer and referenced glazing publications, to comply with system
performance requirements.
0.1
Allow for thermal movements from ambient and surface temperature changes acting on glass
framing members and glazing components.
Differential values in "Temperature Change" Subparagraph below (for aluminum in particular) are
suitable for most of the United States.
A.
Temperature Change: [120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material
surfaces] <Insert temperature change>.
Retain first paragraph below for butt-glazed lites.

PRODUCT DATA SHEET 1 - Clean-cut or flat-grind vertical edges of butt-glazed monolithic lites to
produce square edges with slight chamfers at junctions of edges and faces.
Retain paragraph below if any exposed edges or corners are required.
PRODUCT DATA SHEET 2 - Grind smooth and polish exposed glass edges and corners.
GLAZING
088000 - 17
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PART 3 - EXECUTION
SCHEDULE 0 - EXAMINATION
PRODUCT DATA SHEET 0 - Examine framing, glazing channels, and stops, with Installer present, for
compliance with the following:
0.1
0.2
0.3
0.4
Manufacturing and installation tolerances, including those for size, squareness, and offsets at
corners.
Presence and functioning of weep systems.
Minimum required face and edge clearances.
Effective sealing between joints of glass-framing members.
PRODUCT DATA SHEET 1 - Proceed with installation only after unsatisfactory conditions have been
corrected.
SCHEDULE 1 - PREPARATION
PRODUCT DATA SHEET 0 - Clean glazing channels and other framing members receiving glass
immediately before glazing. Remove coatings not firmly bonded to substrates.
PRODUCT DATA SHEET 1 - Examine glazing units to locate exterior and interior surfaces. Label or
mark units as needed so that exterior and interior surfaces are readily identifiable. Do not use materials
that leave visible marks in the completed Work.
SCHEDULE 2 - GLAZING, GENERAL
PRODUCT DATA SHEET 0 - Comply with combined written instructions of manufacturers of glass,
sealants, gaskets, and other glazing materials, unless more stringent requirements are indicated, including
those in referenced glazing publications.
PRODUCT DATA SHEET 1 - Protect glass edges from damage during handling and installation. Remove
damaged glass from Project site and legally dispose of off Project site. Damaged glass includes glass with
edge damage or other imperfections that, when installed, could weaken glass, impair performance, or
impair appearance.
PRODUCT DATA SHEET 2 - Apply primers to joint surfaces where required for adhesion of sealants, as
determined by preconstruction testing.
PRODUCT DATA SHEET 3 - Install setting blocks in sill rabbets, sized and located to comply with
referenced glazing publications, unless otherwise required by glass manufacturer. Set blocks in thin
course of compatible sealant suitable for heel bead.
PRODUCT DATA SHEET 4 - Do not exceed edge pressures stipulated by glass manufacturers for
installing glass lites.
GLAZING
088000 - 18
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 5 - Provide spacers for glass lites where length plus width is larger than 50
inches (1270 mm).
5.1
5.2
Locate spacers directly opposite each other on both inside and outside faces of glass. Install
correct size and spacing to preserve required face clearances, unless gaskets and glazing tapes
are used that have demonstrated ability to maintain required face clearances and to comply with
system performance requirements.
Provide 1/8-inch (3-mm) minimum bite of spacers on glass and use thickness equal to sealant
width. With glazing tape, use thickness slightly less than final compressed thickness of tape.
PRODUCT DATA SHEET 6 - Provide edge blocking where indicated or needed to prevent glass lites
from moving sideways in glazing channel, as recommended in writing by glass manufacturer and
according to requirements in referenced glazing publications.
PRODUCT DATA SHEET 7 - Set glass lites in each series with uniform pattern, draw, bow, and similar
characteristics.
PRODUCT DATA SHEET 8 - Set glass lites with proper orientation so that coatings face exterior or
interior as specified.
Retain both paragraphs below if glazing with wedge-shaped gaskets is required for Project.
PRODUCT DATA SHEET 9 - Where wedge-shaped gaskets are driven into one side of channel to
pressurize sealant or gasket on opposite side, provide adequate anchorage so gasket cannot walk out when
installation is subjected to movement.
PRODUCT DATA SHEET 10 - Square cut wedge-shaped gaskets at corners and install gaskets in a
manner recommended by gasket manufacturer to prevent corners from pulling away; seal corner joints
and butt joints with sealant recommended by gasket manufacturer.
SCHEDULE 3 - TAPE GLAZING
PRODUCT DATA SHEET 0 - Position tapes on fixed stops so that, when compressed by glass, their
exposed edges are flush with or protrude slightly above sightline of stops.
PRODUCT DATA SHEET 1 - Install tapes continuously, but not necessarily in one continuous length. Do
not stretch tapes to make them fit opening.
PRODUCT DATA SHEET 2 - Cover vertical framing joints by applying tapes to heads and sills first, then
to jambs. Cover horizontal framing joints by applying tapes to jambs, then to heads and sills.
PRODUCT DATA SHEET 3 - Place joints in tapes at corners of opening with adjoining lengths butted
together, not lapped. Seal joints in tapes with compatible sealant approved by tape manufacturer.
PRODUCT DATA SHEET 4 - Do not remove release paper from tape until right before each glazing unit
is installed.
Delete first paragraph below if not required, or qualify by adding "where indicated" and indicate locations
on Drawings.
GLAZING
088000 - 19
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 5 - Apply heel bead of elastomeric sealant.
PRODUCT DATA SHEET 6 - Center glass lites in openings on setting blocks, and press firmly against
tape by inserting dense compression gaskets formed and installed to lock in place against faces of
removable stops. Start gasket applications at corners and work toward centers of openings.
Delete paragraph below if not applicable or revise; it assumes fixed stop is located on exterior.
PRODUCT DATA SHEET 7 - Apply cap bead of elastomeric sealant over exposed edge of tape.
SCHEDULE 4 - GASKET GLAZING (DRY)
PRODUCT DATA SHEET 0 - Cut compression gaskets to lengths recommended by gasket manufacturer
to fit openings exactly, with allowance for stretch during installation.
PRODUCT DATA SHEET 1 - Insert soft compression gasket between glass and frame or fixed stop so it
is securely in place with joints miter cut and bonded together at corners.
PRODUCT DATA SHEET 2 - Installation with Drive-in Wedge Gaskets: Center glass lites in openings on
setting blocks, and press firmly against soft compression gasket by inserting dense compression gaskets
formed and installed to lock in place against faces of removable stops. Start gasket applications at corners
and work toward centers of openings. Compress gaskets to produce a weathertight seal without
developing bending stresses in glass. Seal gasket joints with sealant recommended by gasket
manufacturer.
PRODUCT DATA SHEET 3 - Installation with Pressure-Glazing Stops: Center glass lites in openings on
setting blocks, and press firmly against soft compression gasket. Install dense compression gaskets and
pressure-glazing stops, applying pressure uniformly to compression gaskets. Compress gaskets to produce
a weathertight seal without developing bending stresses in glass. Seal gasket joints with sealant
recommended by gasket manufacturer.
PRODUCT DATA SHEET 4 - Install gaskets so they protrude past face of glazing stops.
SCHEDULE 5 - SEALANT GLAZING (WET)
PRODUCT DATA SHEET 0 - Install continuous spacers, or spacers combined with cylindrical sealant
backing, between glass lites and glazing stops to maintain glass face clearances and to prevent sealant
from extruding into glass channel and blocking weep systems until sealants cure. Secure spacers or
spacers and backings in place and in position to control depth of installed sealant relative to edge
clearance for optimum sealant performance.
PRODUCT DATA SHEET 1 - Force sealants into glazing channels to eliminate voids and to ensure
complete wetting or bond of sealant to glass and channel surfaces.
PRODUCT DATA SHEET 2 - Tool exposed surfaces of sealants to provide a substantial wash away from
glass.
GLAZING
088000 - 20
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
SCHEDULE 6 - CLEANING AND PROTECTION
PRODUCT DATA SHEET 0 - Immediately after installation remove nonpermanent labels and clean
surfaces.
PRODUCT DATA SHEET 1 - Protect glass from contact with contaminating substances resulting from
construction operations. Examine glass surfaces adjacent to or below exterior concrete and other masonry
surfaces at frequent intervals during construction, but not less than once a month, for buildup of dirt,
scum, alkaline deposits, or stains.
1.1
If, despite such protection, contaminating substances do come into contact with glass, remove
substances immediately as recommended in writing by glass manufacturer. Remove and replace
glass that cannot be cleaned without damage to coatings.
PRODUCT DATA SHEET 2 - Remove and replace glass that is damaged during construction period.
Retain paragraph below to suit Project. Delete if covered in Section 017700 "Closeout Procedures."
PRODUCT DATA SHEET 3 - Wash glass on both exposed surfaces not more than four days before date
scheduled for inspections that establish date of Substantial Completion. Wash glass as recommended in
writing by glass manufacturer.
SCHEDULE 7 - MONOLITHIC GLASS SCHEDULE
Monolithic glass refers to glass that is made in a single sheet without being laminated.
Copy paragraphs below and re-edit for each type of glass required.
Insert drawing designation. Use these designations on Drawings to identify each glass type.
If thickness designations are indicated on Drawings or are determined solely by compliance with
"Performance Requirements" Article, delete "Minimum Thickness" subparagraphs.
PRODUCT DATA SHEET 0 - Glass Type [GL-<#>]: Clear [annealed] [heat-strengthened] [fully
tempered] float glass.
0.1
Minimum Thickness: [6 mm] <Insert thickness designation>.
Retain subparagraph below if required; "fully tempered" option must be retained in paragraph above if
safety glazing is required.
0.2
Safety glazing required.
PRODUCT DATA SHEET 1 - Glass Type [GL-<#>]: Ultraclear [annealed] [heat-strengthened] [fully
Retain "Basis-of-Design Product" Subparagraph below to require a specific product or an approved equal
product from manufacturers listed in "Manufacturers" Article.
1.1
Basis-of-Design Product: AGC Glass Company North America; Krystal Klear.
GLAZING
088000 - 21
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
1.2
Minimum Thickness: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] <Insert thickness
designation>.
1.3
PRODUCT DATA SHEET 2 - Glass Type [GL-<#>]: Sputtered Coated Low-Emissivity Clear
Vision Glass.
2.1
Basis-of-Design Product: AGC Glass Company North America; [Energy Select 28] [Energy
Select 31] [Energy Select 36] [Energy Select 40] [Energy Select R42] [Energy Select 63].
Consider retaining option in first subparagraph below if applicable; option is based on ASTM C 1376.
2.2
Kind: Kind CV (coated vision glass)[, except that Kind CO (coated overhead glass) may be
used where the lower edge of the glass is more than 6 feet (1.8 m) above the adjacent floor
level or cannot be approached closer than 10 feet (3.0 m)].
2.3
Coating Color: Neutral
2.4
Glass: Clear float.
2.5
PRODUCT DATA SHEET 3 - Glass Type [GL-<#>]: Sputtered Coated Low-Emissivity Tinted
Vision Glass.
3.1
Basis-of-Design Product: AGC Glass Company North America; [Energy Select 20] [Energy
Select 25].
3.2
3.3
3.4
Glass: Tinted float.
3.5
Tint Color: [Pure Grey] [Pure Bronze] [Meadow Green] [Forest Green] <Insert color>.
3.6
PRODUCT DATA SHEET 4 - Glass Type [GL-<#>]: Pyrolytic Coated Low-Emissivity Clear
Vision Glass.
4.1
Basis-of-Design Product: AGC Glass Company North America; Energy Select 73.
4.2
4.3
4.4
Glass: Clear float.
4.5
GLAZING
088000 - 22
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 5 - Glass Type [GL-<#>]: Pyrolytic Coated Low-Emissivity Tinted
Vision Glass.
5.1
Basis-of-Design Product: AGC Glass Company North America, Sunergy.
5.2
5.3
5.4
Glass: Tinted float.
5.5
Tint Color: [Green] [Grey] [Azur] [Dark Blue].
5.6
PRODUCT DATA SHEET 6 - Glass Type [GL-<#>]: Tinted [annealed] [heat-strengthened] [fully
6.1
6.2
6.3
Basis-of-Design Product: AGC Glass Company North America; Solarshield.

Tint Color: Solarshield [Pure Grey] [Pure Bronze] [Pure Green] [Meadow Green] [Forest
Green] [Pure Blue] [Sky Blue] [Midnight Blue] <Insert color>.
designation>.
Insert performance properties, if required, in "Winter Nighttime U-Factor," "Summer Daytime U-Factor,"
"Visible Light Transmittance," and "Solar Heat Gain Coefficient" subparagraphs below to suit product(s).
6.4
Winter Nighttime U-Factor: <Insert value> maximum.
6.5
Summer Daytime U-Factor: <Insert value> maximum.
6.6
Visible Light Transmittance: <Insert number> percent minimum.
6.7
Solar Heat Gain Coefficient: <Insert value> maximum.
6.8
PRODUCT DATA SHEET 7 - Glass Type [GL-<#>]: Ceramic-coated vision glass; [heat-strengthened]
[fully tempered] float glass.
AGC Glass Company North America does not produce silk-screened glass; however, AGC Glass
Company North Americas glazing products may be used in the fabrication of silk-screened glass by an
AGC Glass Company North America approved fabricator.
7.1
7.2
Basis-of-Design Product: AGC Glass Company North America; <Insert fabricators name;
product name or designation>.
Glass: [Clear] [Ultraclear] [Tinted] float glass.
GLAZING
088000 - 23
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
7.3
7.4
7.5
7.6
Green] [Pure Blue] [Sky Blue] [Midnight Blue]<Insert color>.
Ceramic Coating Color and Pattern: [As selected by Architect from manufacturer's full
range] [Match Architects samples] <Insert one manufacturers color and pattern
designation if matching is required> <Insert manufacturer; color and pattern
designation> [1/8 inch Dots on 1/4 inch Centers (40% Coverage)] [1/8 inch Lines on 1/4
inch Centers (50% Coverage)] [1/8 inch Holes on 1/4 inch Centers (60% Coverage)].
designation>.
Coating Location: Second surface.
7.7
7.8
7.9
7.10
7.11
PRODUCT DATA SHEET 8 - Glass Type [GL-<#>]: Reflective-coated vision glass; [annealed] [heatstrengthened] [fully tempered] float glass.
8.1
Basis-of-Design Product: AGC Glass Company North America; [Stopsol Classic] [Stopsol
SuperSilver] [Stopsol SilverLight].
Consider retaining option in "Kind" Subparagraph below if applicable; option is based on ASTM C 1376.
8.2
Pyrolytic coatings may be used on either the first or the second surface of monolithic-glass lites.
Sputtered coatings may only be used with monolithic glass if recommended by manufacturer, and then
only on the second surface.
8.3
Coating Type: Pyrolytic.
Retain one color from options in "Coating Color" Subparagraph below. Not all sputtered-coating colors
are suitable for monolithic applications and must be on second surface for monolithic applications.
8.4
Coating Color: [Classic - Gold] [SuperSilver - Pewter] [SilverLight - Silver] <Insert color>.
8.5
Glass: [Clear] [Tinted] float glass.
Retain one of three "Tint Color" subparagraphs below to correspond with AGC Glass Company North
America product selected in "Basis-of-Design Product" subparagraph above.
GLAZING
088000 - 24
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
8.6
8.7
8.8
8.9
8.10
Tint Color, Stopsol Classic: [Clear] [Dark Blue] [Bronze] [Green] [Grey].
Tint Color, Stopsol SuperSilver: [Clear] [Green] [Grey] [Dark Blue].
Tint Color, Stopsol SilverLight: Priva Blue.
Coating Location: [First][Second] surface.
Insert performance properties, if required, in "Outdoor Visible Reflectance," "Winter Nighttime UFactor," "Summer Daytime U-Factor," "Visible Light Transmittance," and "Solar Heat Gain Coefficient"
subparagraphs below to suit product(s).
8.11
Outdoor Visible Reflectance: <Insert number> percent maximum.
8.12
8.13
8.14
8.15
Retain "Low-Maintenance Coating" Subparagraph below only with sputter-coated clear float glass and
only after verifying availability.
8.16
Low-Maintenance Coating: Pyrolytic coating on first surface.
8.17
AGC Glass Company North America does not produce spandrel glass; however, AGC Glass Company
North Americas glazing products may be used in the fabrication of spandrel glass by an AGC Glass
Company North America approved fabricator.
PRODUCT DATA SHEET 9 - Glass Type [GL-<#>]:
strengthened] [fully tempered] float glass.
Ceramic-coated
spandrel
glass;
[heat-
9.1
9.2
9.3
9.4
9.5
9.6
Coating Color: [As selected by Architect from manufacturer's full range] [Green] [Grey]
[Black] [Warm Grey] [Charcoal] [Bronze] [Lava Bronze] [Blue] [Dark Green] [White]
[Privacy Grey].
designation>.
Insert performance properties, if required, in "Winter Nighttime U-Factor" and "Summer Daytime UFactor" subparagraphs below to suit product(s).
9.7
9.8
GLAZING
088000 - 25
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Requirement in "Fallout Resistance" Subparagraph below is optional test in ASTM C 1048 and is not
required by the IBC.
9.9
Fallout Resistance: Passes fallout-resistance test in ASTM C 1048 for an assembly of glass and
adhered reinforcing material.
Silicone-coated
spandrel
glass;
[heat-
10.1
10.2
10.3
10.4
10.5
10.6
product name or designation>
Coating Color: [As selected by Architect from manufacturer's full range] [Green] [Grey]
[Bronze] [Warm Grey] [Black].
designation>.
10.7
10.8
10.9
Reflective-coated
spandrel
glass;
[heat-
11.1
Basis-of-Design Product: AGC Glass Company North America; Stopsol [Classic]

[SuperSilver] [SilverLight].
GLAZING
088000 - 26
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
Pyrolytic coatings may be used on either the first or the second surface of monolithic-glass lites.
Sputtered coatings may only be used with monolithic glass if recommended by manufacturer, and then
only on the second surface.
11.2
Coating Type: Pyrolytic.
11.3
Coating Color: [Classic - Gold] [SuperSilver - Pewter] [SilverLight - Silver] <Insert color>.
11.4
Glass: [Clear] [Tinted] float glass.
Retain one of three "Tint Color" subparagraphs below to correspond with AGC Glass Company North
America product selected in "Basis-of-Design Product" subparagraph above.
11.5
Tint Color, Stopsol Classic: [Clear] [Green] [Grey] [Bronze] [Dark Blue].
11.6
Tint Color, Stopsol SuperSilver: [Clear] [Green] [Grey] [Dark Blue].
11.7
Tint Color, Stopsol SilverLight: Priva Blue.
11.8
11.9
Coating Location: [First] [Second] surface.
Insert performance properties, if required, in "Outdoor Visible Reflectance," "Winter Nighttime U-Factor"
and "Summer Daytime U-Factor" subparagraphs below to suit product(s).
11.10
11.11
11.12
11.13
Retain subparagraph below if read-through is not controlled by another means. Opacifier below can be
applied only over reflective coating; verify availability with glass manufacturers.
11.14
Factory apply manufacturer's standard opacifier of the following material to coated second
surface of lites, with resulting products complying with Specification No. 89-1-6 in GANA's
"Engineering Standards Manual":
Retain one of two subparagraphs below. If retaining a specific material, coordinate with product listing
and verify, with glass manufacturer, availability and suitability for installation indicated.
A.
B.
Manufacturer's standard opacifier material.

Polyester film laminated to glass with solvent-based adhesive.
SCHEDULE 8 - LAMINATED GLASS SCHEDULE

"Performance Requirements" Article, delete "Minimum Thickness of Each Glass Ply" subparagraphs.
GLAZING
088000 - 27
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
AGC Glass Company North America's Defender Impact laminated glass, with 0.060 or 0.090 interlayers,
provides small and large missile protection and is typically specified in section 088853 "Security
Glazing".
PRODUCT DATA SHEET 0 - Glass Type [GL-<#>]: Clear laminated glass with two plies of [annealed]
[heat-strengthened] [fully tempered] [ultraclear annealed] [ultraclear heat-strengthened]
[ultraclear fully tempered] float glass.
0.1
0.2
0.3
Basis-of-Design Product: Clear laminated glass as fabricated by an AGC Glass Company North
America approved Fabricator.
Minimum Thickness of Each Glass Ply: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] [As
indicated] <Insert thickness designation>.
Interlayer Thickness: [0.030 inch (0.76 mm)] [0.060 inch (1.52 mm)] [0.090 inch (2.29 mm)].
Retain subparagraph below if required.

0.4
PRODUCT DATA SHEET 1 - Glass Type [GL-<#>]: Tinted laminated glass with two plies of [annealed]
[heat-strengthened] [fully tempered] float glass with outer ply tinted and inner ply clear.
1.1
1.2
1.3
1.4
Basis-of-Design Product: Tinted laminated glass as fabricated by an AGC Glass Company

North America approved Fabricator.
Tint Color: [Pure Grey] [Pure Bronze] [Pure Green] [Meadow Green] [Forest Green]
<Insert color>.
1.5
1.6
1.7
1.8
1.9
Samples for verification or mockups should be used for laminated glass that has the coating facing the
plastic interlayer due to potential color shift.
PRODUCT DATA SHEET 2 - Glass Type [GL-<#>]: Ceramic-coated, laminated vision glass with two
plies of [heat-strengthened] [fully tempered] float glass.
GLAZING
088000 - 28
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Basis-of-Design Product: Ceramic-coated, laminated vision glass as fabricated by an AGC

Glass Company North America approved Fabricator.
Outer Ply: [Clear] [Ultraclear] [Tinted] float glass.
<Insert color>.
Inner Ply: [Clear] [Ultraclear] float glass.
range] [Match Architect's samples] <Insert one manufacturer's color and pattern
designation>.
Coating Location: [Second] [Third] [Fourth] surface.
2.9
2.10
2.11
2.12
2.13
PRODUCT DATA SHEET 3 - Glass Type [GL-<#>]: Reflective-coated, laminated vision glass with two
plies of [heat-strengthened] [fully tempered] float glass with inner ply clear.
3.1
Basis-of-Design Product: Reflective-coated, laminated vision glass as fabricated by an AGC

Glass Company North America approved Fabricator.
3.2
Pyrolytic coatings may be used on any surface of laminated glass. Sputtered coatings may only be used
on the second or third surface of laminated glass.
3.3
Coating Type: [Pyrolytic] [Sputter-coating (vacuum deposition process)].
GLAZING
088000 - 29
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
3.4
Coating Color: [Gold] [Pewter] [Silver] <Insert color>.
3.5
Outer Ply: [Clear] [Tinted] float glass.
3.6
<Insert color>.
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
PRODUCT DATA SHEET 4 - Glass Type [GL-<#>]: Low-E-coated, laminated vision glass with two
plies of clear [annealed] [heat-strengthened] [fully tempered] float glass.
4.1
4.2
4.3
4.4
Basis-of-Design Product: Low-E-coated, laminated vision glass as fabricated by an AGC Glass

Company North America approved Fabricator.
Low-E Coating: [Pyrolytic on second] [Sputtered on second] surface.
4.5
4.6
4.7
4.8
GLAZING
088000 - 30
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
4.9
PRODUCT DATA SHEET 5 - Glass Type [GL-<#>]: Reflective-coated, laminated spandrel glass with
two plies of [heat-strengthened] [fully tempered] float glass with inner ply clear.
5.1
Pyrolytic coatings may be used on any surface of laminated glass. Sputtered coatings may only be used
on the second or third surface of laminated glass.
5.2
5.3
5.4
Outer Ply: [Clear] [Tinted] float glass.
5.5
<Insert color>.
5.6
5.7
5.8
Coating Location: [Second] [Third] [Fourth] surface.
Insert performance properties, if required, in "Outdoor Visible Reflectance," "Winter Nighttime UFactor," and "Summer Daytime U-Factor" subparagraphs below to suit product(s).
5.9
5.10
5.11
SCHEDULE 9 - INSULATING GLASS SCHEDULE
"Performance Requirements" Article, delete "Minimum Thickness of Each Glass Lite" subparagraphs.
GLAZING
088000 - 31
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
PRODUCT DATA SHEET 0 - Glass Type [GL-<#>]: Clear insulating glass.
0.1
0.2
0.3
0.4
0.5
0.6
Basis-of-Design Product: AGC Glass Company North America; <Insert product name or
designation>.
Overall Unit Thickness: [1 inch (25 mm)] [5/8 inch (16 mm)] <Insert dimension>.
Minimum Thickness of Each Glass Lite: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] <Insert
thickness designation>.
Outdoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] float glass.
Interspace Content: [Air] [Argon].
Indoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] float glass.
0.7
0.8
Retain subparagraph below if required; "fully tempered" option must be retained in "Outdoor Lite" and
Indoor Lite" subparagraphs if safety glazing is required.
0.9
PRODUCT DATA SHEET 1 - Glass Type [GL-<#>]: Ultraclear insulating glass.
1.1
1.2
1.3
1.4
1.5
1.6
Basis-of-Design Product: AGC Glass Company North America; Krystal Klear.

Outdoor Lite: Ultraclear [annealed] [heat-strengthened] [fully tempered] float glass.
Indoor Lite: Ultraclear [annealed] [heat-strengthened] [fully tempered] float glass.
1.7
1.8
1.9
PRODUCT DATA SHEET 2 - Glass Type [GL-<#>]: Low-E-coated, clear insulating glass.
GLAZING
088000 - 32
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
2.1
2.2
2.3
2.4
2.5
2.6
2.7
designation>.
Outdoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] [Ultraclear annealed]
[Ultraclear heat-strengthened] [Ultraclear fully tempered] float glass.
Indoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] [Ultraclear annealed]
Low-E Coating: [Pyrolytic on second] [Pyrolytic on third] [Sputtered on second] [Sputtered
on third] [Pyrolytic or sputtered on second or third] surface.
2.8
2.9
2.10
2.11
Retain subparagraph below if required; "fully tempered" or "ultraclear fully tempered" option must be
retained in "Outdoor Lite" and Indoor Lite" subparagraphs if safety glazing is required.
2.12
2.13
PRODUCT DATA SHEET 3 - Glass Type [GL-<#>]: Tinted insulating glass.
3.1
3.2
3.3
3.4
3.5
3.6
3.7
designation>.
Outdoor Lite: Tinted [annealed] [heat-strengthened] [fully tempered] float glass.
<Insert color>.
Indoor Lite: Clear [annealed] [heat-strengthened] [fully tempered] float glass.
3.8
3.9
3.10
3.11
GLAZING
088000 - 33
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
3.12
PRODUCT DATA SHEET 4 - Glass Type [GL-<#>]: Low-E-coated, tinted insulating glass.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
designation>.
<Insert color>.
Low-E Coating: [Pyrolytic low-E on second surface] [Pyrolytic low-E on third surface]
[Sputtered on second surface] [Sputtered on third surface] [Pyrolytic or sputtered on
second or third surface] [Pyrolytic low-E in combination with Energy Select 73 Pyrolytic
low-E on second and fourth surfaces] [Combined with sputter coated glass on second
surface and pyrolytic on fourth surface (U4 4th Surface Technology by AGC)].
4.9
4.10
4.11
4.12
4.13
AGC Glass Company North America does not produce silk-screened glass; however, AGC Glass
Company North Americas glazing products may be used in the fabrication of silk-screened glass by an
AGC Glass Company North America approved fabricator.
PRODUCT DATA SHEET 5 - Glass Type [GL-<#>]: Ceramic-coated, silk-screened, low-E, insulating
vision glass.
5.1
5.2
range] [Match Architect's samples] <Insert one manufacturer's color and pattern
designation>.
GLAZING
088000 - 34
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
Outdoor Lite: [Clear] [Ultraclear] [Tinted] [annealed] [heat-strengthened] [fully tempered]
float glass.
<Insert color>.
Indoor Lite: [Clear] [Ultraclear] [annealed] [heat-strengthened] [fully tempered] float glass.
Silk-screened Ceramic Coating Location: [Second] [Third] [Fourth] surface.
on third] [Pyrolytic or sputtered on second and third] surface.
5.11
5.12
5.13
5.14
Retain subparagraph below if required; "fully tempered" or "ultraclear fully tempered" option must be
retained in "Outdoor Lite" and Indoor Lite" subparagraphs if safety glazing is required.
5.15
PRODUCT DATA SHEET 6 - Glass Type [GL-<#>]: Reflective-coated, insulating glass.
6.1
designation>.
6.2
Pyrolytic coatings may be used on any surface of insulating glass. Sputtered coatings may only be used
on the second or third surface of insulating glass.
6.3
6.4
6.5
6.6
6.7
Outdoor Lite: [Clear] [Tinted] [annealed] [heat-strengthened] [fully tempered] float glass.
6.8
<Insert color>.
GLAZING
088000 - 35
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
6.9
6.10

Pyrolytic coatings may be used on any surface of insulating glass. Sputtered coatings may only be used
on the second or third surface of insulating glass.
6.11
Reflective Coating Location: [First] [Second] [Third] surface.
6.12
6.13
6.14
6.15
6.16
6.17
6.18
PRODUCT DATA SHEET 7 - Glass Type [GL-<#>]: [Ceramic] [Silicone]-coated, insulating spandrel
glass.
7.1
7.2
7.3
7.4
7.5
7.6
Coating Color: [As selected by Architect from manufacturer's full range] [Match
Architect's samples] <Insert one manufacturer's color designation if matching is
required> <Insert manufacturer; color designation>.
Overall Unit Thickness: [1 inch (25 mm)] <Insert dimension>.
Outdoor Lite: [Clear] [Ultraclear] [annealed] [heat-strengthened] [fully tempered] float
glass.
Retain "heat-strengthened" or "fully tempered" option in "Indoor Lite" Subparagraph below for ceramiccoated, insulating spandrel glass.
7.7
Indoor Lite: [Clear] [Ultraclear] [annealed] [heat-strengthened] [fully tempered] float glass.
7.8
Spandrel Coating Location: Fourth surface.
GLAZING
088000 - 36
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
7.9
7.10
PRODUCT DATA SHEET 8 - Glass Type [GL-<#>]: [Ceramic] [Silicone]-coated, low-E, insulating
spandrel glass.
8.1
8.2
8.3
8.4
8.5
8.6
Outdoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] [Ultraclear annealed]
Retain "heat-strengthened" or "fully tempered" option in "Indoor Lite" Subparagraph below for ceramiccoated, low-E, insulating spandrel glass.
8.7
Indoor Lite: [Annealed] [Heat-strengthened] [Fully tempered] [Ultraclear annealed]
8.8
8.9
Opaque Coating Location: Fourth surface.
8.10
8.11
PRODUCT DATA SHEET 9 - Glass
insulating spandrel glass.
Type [GL-<#>]:
[Ceramic-coated]
[Silicone-coated],
tinted,
GLAZING
088000 - 37
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
9.1
9.2
9.3
9.4
9.5
9.6
9.7
<Insert color>.
Retain "heat-strengthened" or "fully tempered" option in "Indoor Lite" Subparagraph below for ceramiccoated, tinted, insulating spandrel glass.
9.8
9.9
9.10
9.11
PRODUCT DATA SHEET 10 - Glass Type [GL-<#>]: [Ceramic-coated] [Silicone-coated], Lowe Coated, tinted, insulating spandrel glass.
10.1
10.2
10.3
10.4
10.5
Thickness of Each Glass Lite: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] <Insert thickness
designation>.
Outdoor Lite: Tinted [float glass] [heat-strengthened float glass] [fully tempered float
glass].
Retain either heat-strengthened or fully tempered float glass option in first subparagraph below for
ceramic-coated, tinted, insulating spandrel glass.
10.6
Indoor Lite: Clear [float glass] [heat-strengthened float glass] [fully tempered float glass].
10.7
Low-E Coating: [Pyrolytic on second] [Pyrolytic on third] [Sputtered on second]
[Sputtered on third] [Pyrolytic or sputtered on second or third] surface.
10.8
10.9
10.10
GLAZING
088000 - 38
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
[Silicone-coated], low-e, clear insulating spandrel glass.
11.1
11.2
11.3
11.4
Reflective-coated, [Ceramic-coated]
designation>.
Outdoor Lite: Clear, [Float glass] [Heat-strengthened float glass] [Fully tempered float
glass].
ceramic-coated, low-e, insulating spandrel glass.
11.5
Indoor Lite: [Float glass] [Heat-strengthened float glass] [Fully tempered float glass].
11.6
Reflective coating Location: [First] [Second] [Third] surface.
11.7
Low-E Coating: [Pyrolytic on second] [Pyrolytic on third] [Pyrolytic on second or third]
surface.
11.8
11.9
11.10
[Silicone-coated], low-e, tinted insulating spandrel glass.
12.1
12.2
12.3
12.4
Reflective-coated, [Ceramic-coated]
designation>.
Outdoor Lite: Tinted, [Float glass] [Heat-strengthened float glass] [Fully tempered float
glass].
ceramic-coated, low-e, insulating spandrel glass.
12.5
Indoor Lite: [Float glass] [Heat-strengthened float glass] [Fully tempered float glass].
12.6
Reflective coating Location: [First] [Second] [Third] surface.
12.7
Low-E Coating: [Pyrolytic on second] [Pyrolytic on third] [Pyrolytic on second or third]
surface.
12.8
12.9
12.10
GLAZING
088000 - 39
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
SCHEDULE 10 - INSULATING-LAMINATED-GLASS SCHEDULE
Glass types in this article are primarily for sloped glazing and glazing that is required to be windbornedebris-impact resistant.
"Performance Requirements" Article, delete "Minimum Thickness of Outdoor Lite" and "Minimum
Thickness of Each Glass Ply" subparagraphs.
PRODUCT DATA SHEET 0 - Glass Type [GL-<#>]: Clear insulating laminated glass.
0.1
designation>.
Overall Unit Thickness: [1-5/16 inch (33 mm)] [1 inch (25 mm)] [3/4 inch (19 mm)] <Insert
dimension>.
Minimum Thickness of Outdoor Lite: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] <Insert
Outdoor Lite: [Heat-strengthened] [Fully tempered] float glass.
Indoor Lite: Clear laminated glass with two plies of [annealed] [heat-strengthened] [fully
0.2
0.3
0.4
0.5
0.6
A.
B.
and "Solar Heat Gain Coefficient" subparagraphs below to suit product(s).
0.7
0.8
0.9


0.10
PRODUCT DATA SHEET 1 - Glass Type [GL-<#>]: Low-E-coated, clear insulating laminated glass.
1.1
designation>.
GLAZING
088000 - 40
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
1.2
dimension>.
Outdoor Lite: Clear [Heat-strengthened] [Fully tempered] float glass.
1.3
1.4
1.5
1.6
A.
B.
1.7
on third] surface.
1.8
1.9
1.10
1.11
1.12
PRODUCT DATA SHEET 2 - Glass Type [GL-<#>]: Tinted, insulating laminated glass.
2.1
designation>.
dimension>.
Outdoor Lite: Tinted [heat-strengthened] [fully tempered] float glass.
<Insert color>.
2.2
2.3
2.4
2.5
2.6
2.7
A.
B.
GLAZING
088000 - 41
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
2.8
2.9
2.10
2.11


2.12
PRODUCT DATA SHEET 3 - Glass Type [GL-<#>]: Low-E-coated, tinted, insulating laminated glass.
Retain "Basis-of-Design Product" Subparagraph below to require a specific product or a comparable
3.1
designation>.
dimension>.
Outdoor Lite: Low-E coated, tinted, [heat-strengthened] [fully tempered] float glass.
<Insert color>.
3.2
3.3
3.4
3.5
3.6
3.7
A.
B.
3.8
Low-E Coating: [Pyrolytic on second] [Sputtered on second] surface.
3.9
3.10
3.11
3.12
3.13
PRODUCT DATA SHEET 4 - Glass Type [GL-<#>]: Reflective-coated, insulating laminated glass.
4.1
designation>.
GLAZING
088000 - 42
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
4.2
Pyrolytic coatings may be used on the first, second, or third surface of insulating laminated glass.
Sputtered coatings is only used on the second or third surface of insulating laminated glass.
4.3
4.4
4.5
Overall Unit Thickness: [1-5/16 inch (33 mm)] [1 inch (25 mm)] <Insert dimension>.
4.6
4.7
Outdoor Lite: [Clear] [Tinted], [heat-strengthened] [fully tempered] float glass.
4.8
<Insert color>.
4.9
4.10
A.
B.
4.11
Coating Location: [First] [Second] [Third] surface.
4.12
4.13
4.14
4.15
4.16
4.17
4.18
laminated glass.
5.1
5.2
Reflective-coated, low-E, insulating
Overall Unit Thickness: [1-5/16 inch (33 mm)] [1 inch (25 mm)] <Insert dimension>.
Thickness of Outdoor Lite: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] <Insert thickness
designation>.
GLAZING
088000 - 43
Copyright 2014 AIA

MasterSpec Premium
06/14
AMERICA.
5.3
5.4
5.5
5.6
A.
B.
5.7
5.8
5.9
5.10
5.11
Outdoor Lite: [Clear] [Tinted] [heat-strengthened float glass] [fully tempered float glass].
<Insert color>.
Indoor Lite: Clear laminated glass with two plies of [float glass] [heat-strengthened float
glass] [fully tempered float glass].
Thickness of Each Glass Ply: [3 mm] [5 mm] [6 mm] [10 mm] [12 mm] [As indicated]
<Insert thickness designation>.
Low-e Coating Location: [Pyrolytic on second] [Pyrolytic on third] [Sputtered on second]
surface.
Reflective Coating Location: [Second] [Third] surface.

5.12
Provide safety glazing labeling.
END OF SECTION 088000
GLAZING
088000 - 44

FL - Glazing.agc Glass - Update 1 1

Uploaded by

Copyright:

Available Formats

FL - Glazing.agc Glass - Update 1 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FL - Glazing.agc Glass - Update 1 1

Uploaded by

Copyright:

Available Formats

Copyright 2014 AIA

Copyright 2014 AIA

PRODUCT DATA SHEET 1 - Related Requirements:

Section 057300 "Decorative Metal Railings" for glazing in railings.

Copyright 2014 AIA

SCHEDULE 5 - ACTION SUBMITTALS

Product Data: For sealants, indicating VOC content.

Copyright 2014 AIA

PRODUCT DATA SHEET 3 - Preconstruction adhesion and compatibility test report.

Copyright 2014 AIA

Install glazing in mockups specified in [Section 084113 "Aluminum-Framed Entrances and

SCHEDULE 9 - DELIVERY, STORAGE, AND HANDLING

Copyright 2014 AIA

Warranty Period: Five years from date of Substantial Completion.

Copyright 2014 AIA

Copyright 2014 AIA

Trulite Glass & Aluminum Solutions, LLC.

Obtain tinted glass from single source from single manufacturer.

Design Wind Pressures: As indicated on Drawings.

Wind Design Data: As indicated on Drawings.

Copyright 2014 AIA

Large-Missile Test: For glazing located within 30 feet (9.1 m) of grade.

Copyright 2014 AIA

For laminated-glass lites, properties are based on products of construction indicated.

SCHEDULE 2 - GLASS PRODUCTS, GENERAL

GANA Publications: ["Laminated Glazing Reference Manual" and ]"Glazing Manual."

Copyright 2014 AIA

Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to

If heat soaking of fully tempered glass is needed, insert requirements here.

Copyright 2014 AIA

Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to

If heat soaking of fully tempered glass is needed, insert requirements here.

Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to

Copyright 2014 AIA

Polyvinyl butyral interlayer.

SCHEDULE 5 - INSULATING GLASS

Copyright 2014 AIA

Sealing System: Dual seal, with [manufacturer's standard] [polyisobutylene and

If retaining a specific spacer material, coordinate with manufacturers and products.

Manufacturers: Subject to compliance with requirements, provide products by one of the

Copyright 2014 AIA

Dow Corning Corporation.

Manufacturers: Subject to compliance with requirements, provide products by one of the

BASF Corporation-Construction Systems.

Manufacturers: Subject to compliance with requirements, provide products by one of the

Copyright 2014 AIA

Manufacturers: Subject to compliance with requirements, provide products by one of the

BASF Corporation-Construction Systems.

SCHEDULE 7 - GLAZING TAPES

AAMA 804.3 tape, where indicated.

SCHEDULE 8 - MISCELLANEOUS GLAZING MATERIALS

Copyright 2014 AIA

Retain first paragraph below for butt-glazed lites.

Copyright 2014 AIA

Copyright 2014 AIA

Copyright 2014 AIA

Copyright 2014 AIA

Minimum Thickness: [6 mm] <Insert thickness designation>.

Basis-of-Design Product: AGC Glass Company North America; Krystal Klear.