k3vl B Datasheet
k3vl B Datasheet
k3vl B Datasheet
Pumps
Sizes 45, 80, 112, 140
and 200
Up to 203 kW
and 320bar
Swash-plate
Axial Piston Pump
B Series K3VL
Features
SAE and ISO mount.
Pressure compensation.
Through drive.
Load sensing.
Integral unload.
Torque limiter.
Rigid construction.
Low pulsation.
Super-finished bores.
Overcentre bleed.
Solid pistons.
Model
K3VL
Page
1.64
Data Sheet
P-1002/01.06
Data Sheet
P-1002/01.06
GB
Industrial Products
Pumps
General Description
The K3VL Series Swash Plate Type Axial Piston Pumps are designed to specifically satisfy the mobile,
marine and general industrial machinery market where a medium pressure variable displacement pump is
required. K3VL Pumps are available in nominal displacements ranging from 45 to 200 cm3/rev with various
pressure, torque limiter, and combination load sensing control options.
Technical Description
The components of the K3VL pump can be divided into three sub-groupings:
Rotating Group
Model
K3VL
Page
2.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Description (continued)
The Rotating Group
The Rotating Group comprises:
(a)
(b)
(c)
(d)
(e)
(f)
(g)
The drive shaft is coupled to the cylinder block through a splined section and supported at both of its ends
by bearings and the drive shaft. The shoe is swaged over the spherical end of the piston forming a
spherical ball joint. Additionally the shoe has a hydrostatic pocket to balance the hydraulic thrust developed
by the piston pressure allowing the shoe to lightly slide against the shoe plate.
The subgroup consisting of the pistons and shoes are pressed against the shoe plate by the cylinder
springs acting through the setting plate and the spherical bush. The force developed by these cylinder
springs also press the cylinder block against the valve plate. With the smallest K3VL45 unit a single
centralised spring with individual push pins provide the shoe and cylinder block hold down force.
Swash Plate Group
The Swash Plate Group comprises:
(a)
(b)
(c)
(d)
(e)
(f)
(g)
The swash plate on the reverse side to the shoe location is a cylindrical form which is a "pillow" supported
by the hydrostatic bearing provided by the swash plate support. The tilting bush is inserted into the swash
plate and into this is installed the spherical portion of the tilting pin which is coupled to the servo piston.
Any linear movement of the servo piston produced by the regulator pressure applied to either end is
translated through the tilting pin into an angular movement of the swash plate which varies the tilting or
swash angle of the pump. A screw adjuster and lock nut is available to adjust the maximum tilting angle
condition. The servo assist springs are provided to ensure good on stroking response particularly at low
operating pressures.
Model
K3VL
Page
3.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Description (continued)
Valve Cover Group
The Valve Cover Group comprises:
(a)
(b)
(c)
The valve plate with its two "kidney" shaped ports is installed onto the valve plate located by the valve plate
pin. These two ports serve to supply and exhaust oil to and from the cylinder block. The oil passage
switched by the valve plate is connected to the externally piped suction and outlet pressure ports through
the valve cover. This valve plate is spherical in form for all but the smallest 45 unit.
Pump Operation
When the pumps drive shaft is driven by a prime mover (Electric motor, Engine etc.), the cylinder block
being spline coupled to the shaft will also rotate. If the swash plate has been tilted, the pistons arranged in
the cylinder block due to the shoe being retained on the swash plate surface will both rotate with the
cylinder block and reciprocate once per revolution. Paying attention to one such piston then it will move
away from the valve plate for half a rotation (suction stroke) and move towards the valve plate for the
second half of rotation (oil delivery stroke). The larger the tilt angle, the longer the piston stroke and the
higher is the pumps displacement. As the swash plate tilting angle approaches so the piston makes no
stroke and thereby delivers no oil.
Through Drive Option
The pump is available with a through drive capability (see installation section) where a through drive shaft
with splined end is incorporated capable of taking a similar torque to that of the pump itself and an SAE "A"
mounting interface is provided.
By suitable use of adaptors and splined couplings a wide variety of through drive mounting capabilities are
available. The formation of these kits and their relevant part numbers will be found in the installation
section.
Model
K3VL
Page
4.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Data
For applications outside the following parameters, please consult Kawasaki Precision Machinery (UK) Ltd.
Hydraulic Data
Pressure Fluid
Mineral oil, phosphate ester, fatty acid ester and water glycol.
Phosphate ester is only suitable for use with FPM seals.
Use a high quality, anti-wear, mineral based hydraulic fluid when the
pressure exceeds 207 bar. In applications where fire resistant fluids
are required consult Kawasaki Precision Machinery (UK) Ltd. The
following chart illustrates the effects on pump life when non-standard
fluids are used:
Fluid selection
1000
22
0
10
VG 68
VG 6
4
VG
32
VG
VG
600
400
200
100
80
60
40
20
15
10
-20
20
40
60
Model
K3VL
Page
5.64
Data Sheet
P-1002/01.06
80
100
Industrial Products
Pumps
Technical Data (continued)
Filtration & Contamination Control
Filtration
The most important means to prevent premature damage to the pump and associated equipment and to
extend its working life, is to ensure that hydraulic fluid contamination control of the system is working
effectively.
This begins by ensuring that at the time of installation that all piping, tanks etc. are rigorously cleaned in a
sanitary way. Flushing should be provided using an off line filtration system
and after flushing the filter elements should be replaced.
A full flow return line filter of 10 micron nominal should be utilised and in addition a 150 micron mesh
suction strainer is recommended. Typical filtration circuits are shown in the K3VL brochure.
To prevent contaminant ingress from the external environment a 5 to 10 micron filter within the tanks
breather is also recommended.
Suggested Acceptable Contamination Level
The relationship between contamination level and pump life is very difficult to predict as it depends on the
type and nature of the contaminant present in the system. Sand or Silica in particular, due to its abrasive
nature, does significantly reduce the expected life of a pump.
Based on the precondition that there is no significant presence of Silica type substances then a minimum
Cleanliness level of 18/15 to ISO/DIS 4406 (NAS Class 9) is recommended.
Working Fluid Types
Anti-Wear Type Hydraulic fluid
It is generally recommended to use an anti-wear type hydraulic fluid as the mineral oil type when the
operating pressure exceeds 210 bar.
Fire-resistant Fluids
Some kind of fire-resistant fluids require special materials for seals, paint and metal finishing. Please
consult Kawasaki Precision Machinery (UK) Limited and provide details of the particular fluid specification
and the working conditions so that any special requirements can be ascertained.
In general, fire-resistant fluids have a low viscosity index and their viscosity also changes significantly with
operating temperature and service life. For this reason, the circuit should be provided with an adequately
sized cooler or forced cooling so that temperatures can be stabilised.
Due to the inherent water content of some of these fluids the minimum allowable suction pressure will be
higher than that of an equivalent mineral oil and so needs to be fully evaluated by Kawasaki Precision
Machinery (UK) Limited. The following table provides an overview of the precautions and characteristics
that can be expected with these types of fluids.
Model
K3VL
Page
6.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Data (continued)
Fire-resistant Fluids (continued)
fluid type:-
mineral
oil
phosphate
ester
polyol
ester
water
glycol
Maximum Pressure
(bar)
320
320
320
210
Recommended Temperature
Range (deg C)
20 ~ 60
20 ~ 60
20 ~ 60
10 ~ 50
100%
60% ~ 100%
50% ~ 100%
20% ~ 80%
parameter :-
Cavitation susceptability
recommended
Model
K3VL
Page
7.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Data (continued)
Pump Start Up Precautions
Pump Case Filling
Be sure to fill the pump casing with oil through the drain port - filling only the suction line with oil is totally
insufficient. The pump contains bearings and high-speed sliding parts including pistons with shoes and
spherical bushes that need to be continuously lubricated. Part seizure or total premature failure will occur
very quickly if this procedure is not rigidly followed.
Piping & Circuit Checking
Check to see that the piping and full hydraulic circuit is completed and that any gate valves etc. are open.
Direction of Rotation Check
Check to ensure that direction of rotation is correct and that the suction and delivery lines are connected
correctly.
Start Up
Jog start the motor and check once more for correct rotation. Run the pump unloaded for a period to ensure
that all residual air within the system is released. Check for external leakage, abnormal noise and vibrations.
Case Drain Pressure
Please ensure, as stated previously, that the maximum steady state drain line pressure at the pump casing
does not exceed 1 bar. (Maximum peak pressure 4 bar). A suitable drain line hose and drain line filter when
required must be selected to ensure this.
Long Term Out of Usage
It is undesirable to leave the pump out of use for a long period of a year or more. In such a situation it is
recommended that the pump is run for a short period on a more frequent basis even if it is just unloaded.
With regard to a pump held in storage then rotating the shaft on a frequent basis is sufficient. If the pump is
left out for more than the suggested time it will require a service inspection.
Model
K3VL
Page
8.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Technical Data (continued)
Specifications
The following table shows the specifications for the complete K3VL pump range.
More detailed efficiency curves and other related information will be found in a later section.
pump model
capacity
cc/rev
pressure ratings
Speed ratings
45
80
112
140
200
45
80
112
140
200
rated
bar
peak
bar
self prime
rpm
2700
2400
2200
2200
1900
max. bosted
rpm
3250
3000
2700
2500
2200
100
320
350
rpm
600
1
case drain
max
bar
pressures
peak
bar
Weight
kg
25
34
60
60
cc
600
800
1000
1000
input shaft
Nm
type
225
SAE B
400
ISO 100
SAE C
981
ISO 125
SAE D
ISO 25mm
SAE C
ISO 32mm
SAE D
ISO 45mm
SAE D
ISO 45mm
SAE D
form
spline &
key
key
spline &
key
key
spline &
key
key
spline &
key
key
spline &
key
61
SAE B
torque
SAE E
SAE B-B
118
SAE B-B
1000
ISO 180
type
SAE A'
allowable
SAE D
bolts
SAE A-A
through drive
981
ISO 180
203
Nm
225
SAE C
400
SAE C-C
559
SAE D
699
1000
Temperature range
viscosity range
cSt
-20 to 95
10 to 1,000
Notes:
Rated Pressure
Pressure at which life and durability will not be affected.
Peak Pressure
The instant allowable surge pressure as defined by DIN 24312. Life and durability however will be
shortened.
Maximum Self Priming Speed
Values are valid for an absolute suction pressure of 1 bar. If the flow is reduced, or if the inlet
pressure is increased the speed may also be increased (refer to section 4.2)
Maximum Boosted Speed
Values stated are the absolute maximum permitted speed for which an increased inlet pressure
will be required. (refer to section 4.2)
Weight
Approximate dry weights, dependant on exact pump type.
Hydraulic Fluid
Mineral anti wear hydraulic fluid for other fluid types please consult KPM
Viscosity Range
If viscosity is in range 200 to 1,000 cSt, then warming up is necessary before commencing full
scale running.
Model
K3VL
Page
9.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Ordering Code K3VL Series
K3VL 80
B 1 0 R S S
L O 12D
Design series
B
Displacement control
(Without torque limit)
/1-E0 Electrical displacement
control (pilot pressure
required)
/1-Q0 Pilot operated
displacement control
Mineral oil
W
Water glycol
Z
Phosphate ester
Circuit type
1
Open circuit
Through drive & porting
0
Single pump, side ported
A
SAE "A" through drive, side ported
B
SAE "B" through drive, side ported
BB
SAE "BB" through drive, side ported
C
SAE "C" through drive, side ported
D
SAE "D" through drive, side ported
R
Single pump, rear ported
S
Single pump with plastic cover (Stock
Pump)
N
Single pump with Steel cover, side ported
Direction of rotation
R
Clockwise rotation
L
Counter-clockwise rotation
Mounting flange & shaft
S
SAE spline & mount (see drawing for detail)
M
ISO key & mount (see drawing for detail) (not 200)
K
SAE key & mount (see drawing for detail)
T*
SAE B spline & SAE B 2 bolt mount for 45
(not 80) SAE CC spline & SAE D 4 bolt mount
for 112/140 (not 200)
U*
45 only, SAE B key & SAE B 2 bolt mount
C*
112/140 only, SAE C spline & SAE C 2 bolt mount
R*
112/140 only, SAE C spline & SAE D 4 bolt mount
X*
112/140 only, SAE C key & SAE C 2 bolt mount
W*
112/140 only, SAE CC spline & SAE C 2 bolt mount
(*Non standard options)
Model
K3VL
/1 H*
Page
10.64
Unloader solenoid
(Type N below)
blank For all other options
except PN & LN
115A 115V AC, 50.60Hz,
DIN 43550 Plug
235A 230V AC, 50.60Hz,
DIN 43550 Plug
12D 12V DC, DIN 43550 Plug
24D 24V DC, DIN 43550 Plug
Additional pressure control
0
No additional control
N
With integrated unloading valve
V
With integrated remote control
valve
R
With inverse integrated remote
control valve
1
Load sensing only (R4 plugged)
Control device configuration
P
Remote pressure compensator
L
Load sensing & pressure control
Porting threads
M
Metric threaded
S
UNC threaded
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Performance - K3VL45
Performance Curve
(Speed Range 1500 rpm & 1800 rpm with atmospheric inlet)
Test temperature 50C, Viscosity 31cSt (ISO VG 46)
Ratio of displacement
1.00 0.75 0.50 0.25
100
1.00
0.90
90
Ratio of Displacement
0.80
80
89
0.70
70
88
0.60
60
86
0.50
50
83
0.40
80
0.30
75
40
30
70
60
0.20
90
20
10
0.10
0.00
0
50
100
150
200
250
300
0
350
Power Curve
Note: Atmospheric Inlet, Full displacement
80
320
300
70
60
250
50
200
40
150
30
100
20
50
25
10
90
0
0
500
1000
1500
2000
2500
Speed (rpm)
Model
K3VL
Page
11.64
Data Sheet
P-1002/01.06
3000
3500
Industrial Products
Pumps
Performance K3VL80
Performance Curve
(Speed Range 1500 rpm & 1800 rpm with atmospheric inlet)
Test temperature 50C, Viscosity 31cSt (ISO VG 46)
Ratio of displacement
1.00 0.75 0.50 0.25
100
1.00
90
92
0.80
80
91
0.70
0.60
70
60
89
0.50
50
87
85
0.40
40
83
80
0.30
30
75
0.20
20
70
10
0.10
0.00
0
50
100
150
200
250
0
350
300
Power Curve
Note: Atmospheric Inlet, Full displacement
100
200
150
50
100
150
50
25
0
0
500
1000
1500
2000
2500
Speed (rpm)
Model
K3VL
Page
12.64
Data Sheet
P-1002/01.06
3000
3500
Ratio of Displacement
0.90
Industrial Products
Pumps
Performance - K3VL112
Performance Curve
(Speed Range 1500 rpm & 1800 rpm with atmospheric inlet)
Test temperature 50C, Viscosity 31cSt (ISO VG 46)
1.00
100
0.90
90
0.80
80
92
70
0.70
91
0.60
60
89
0.50
50
87
0.40
40
85
83
80
0.30
30
75
70
0.20
20
10
0.10
0.00
0
50
100
150
200
250
300
0
350
Power Curve
Note: Atmospheric Inlet, Full displacement
320
300
150
250
200
100
150
100
50
200
50
25
0
0
500
1000
1500
2000
2500
Speed (rpm)
Model
K3VL
Page
13.64
Data Sheet
P-1002/01.06
3000
Ratio of Displacement
Ratio of displacement
1.00 0.75
0.50 0.25
Industrial Products
Pumps
Performance - K3VL140
Performance Curve
(Speed Range 1500 rpm & 1800 rpm with atmospheric inlet)
Test temperature 50C, Viscosity 31cSt (ISO VG 46)
1.00
100
0.90
90
80
0.80
93
70
0.70
92
0.60
60
90
0.50
50
88
0.40
40
86
83
80
75
70
0.30
0.20
30
20
10
0.10
0.00
0
50
100
150
200
250
0
350
300
Power Curve
Note: Atmospheric Inlet, Full displacement
320
300
150
250
200
100
150
100
50
50
25
200
0
0
500
1000
1500
2000
2500
Speed (rpm)
Model
K3VL
Page
14.64
Data Sheet
P-1002/01.06
3000
Ratio of Displacement
Ratio of displacement
1.00 0.75
0.50 0.25
Industrial Products
Pumps
Performance - K3VL200
Performance Curve
(Speed Range 1500 rpm & 1800 rpm with atmospheric inlet)
Test temperature 50C, Viscosity 31cSt (ISO VG 46)
1.00
Ratio of displacement
0.75
0.50
0.25
100
1.00
0.75
75
90
89
87
0.50
50
85
83
80
75
0.25
25
70
0
350
0
0
50
100
150
200
250
300
Power Curve
Note: Atmospheric Inlet, Full displacement
320
300
250
200
150
100
50
25
0
500
1000
1500
2000
Speed (rpm)
Model
K3VL
Page
15.64
Data Sheet
P-1002/01.06
2500
Ratio of Displacement
91
Industrial Products
Pumps
Self Priming Curves
K3VL45 Self Priming Capability
+0,2 bar
3200
+0,1 bar
Speed N (rpm)
3000
Suction
Pressure
Ps (bar)
0 bar
2800
-0,1 bar
2600
at the suction port
of the pump port
-0,2 bar
2400
2200
28
30
32
34
36
38
40
42
44
Displacement q [cc/rev]
3000
+0,3 bar
+0,2 bar
Speed N (rpm)
2800
+0,1 bar
2600
0 bar
2400
-0,1 bar
at the suction port
of the pump port
-0,2 bar
2200
2000
Suction
Pressure
Ps (bar)
50
55
60
65
70
75
Displacement q [cc/rev]
Model
K3VL
Page
16.64
Data Sheet
P-1002/01.06
80
Industrial Products
Pumps
Self Priming Curves (continued)
K3VL112 Self Priming Capability
+ 0,2 bar
2600
Speed N (rpm)
+0,1 bar
2400
0 bar
2200
2000
1800
Suction Pressure
Ps (bar)
-0,2 bar
70
80
90
100
110
Displacement q [cc/rev]
Speed N (rpm)
+0,1 bar
2400
0 bar
2200
-0,1 bar
2000
-0,2 bar
1800
90
100
110
120
130
140
Displacement q [cc/rev]
Model
K3VL
Page
17.64
Data Sheet
P-1002/01.06
Suction Pressure
Ps (bar)
at the suction port
of the pump port
Industrial Products
Pumps
Self Priming Curves
K3VL200 Self Priming Capability
2800
Speed N (rpm)
2600
2400
+0,3 bar
2200
+0,2 bar
+0,1 bar
2000
0 bar
1800
1600
120
-0,1 bar
130
140
150
160
170
180
190
Displacement q [cc/rev]
Model
K3VL
Suction
Pressure
Ps (bar)
Page
18.64
Data Sheet
P-1002/01.06
-0,2 bar
200
at the suction
port of the
pump port
Industrial Products
Pumps
Pressure pulsation
K3VL45 pulsation graph
20
1800rpm
15
1500rpm
10
0
0
50
100
150
200
250
300
350
300
350
20
1800rpm
15
1500rpm
10
0
0
50
100
150
200
250
Model
K3VL
Page
19.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Pressure pulsation (continued)
K3VL112 pulsation graph
20
1800rpm
15
1500rpm
10
0
0
50
100
150
200
250
300
350
300
350
20
1800rpm
15
1500rpm
10
0
0
50
100
150
200
250
Model
K3VL
Page
20.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Pressure pulsation (continued)
K3VL200 pulsation graph
20
1800rpm
15
1500rpm
10
0
0
50
100
150
200
250
Model
K3VL
Page
21.64
Data Sheet
P-1002/01.06
300
350
Industrial Products
Pumps
Bearing Life (Full Displacement)
K3VL45
Note: Service and other life factors have unity value
10,000,000
1,000,000
50 bar
100,000
100 bar
150 bar
10,000
200 bar
1,000
0
500
1000
1500
2000
2500
3000
250 bar
300 bar
320 bar
3500
Speed (rpm)
K3VL80
Note: Service and other life factors have unity value
10,000,000
1,000,000
50 bar
100,000
100 bar
150 bar
10,000
1,000
0
500
1000
1500
2000
2500
Speed (rpm)
Model
K3VL
Page
22.64
Data Sheet
P-1002/01.06
3000
200 bar
250 bar
300 bar
320 bar
3500
Industrial Products
Pumps
Bearing Life (Full Displacement) (continued)
K3VL112
Note: Service and other life factors have unity value
10,000,000
50 bar
1,000,000
100 bar
100,000
150 bar
200 bar
10,000
250 bar
300 bar
320 bar
1,000
0
500
1000
1500
2000
2500
3000
Speed (rpm)
K3VL140
Note: Service and other life factors have unity value
10,000,000
1,000,000
50 bar
100,000
100 bar
150 bar
10,000
200 bar
1,000
500
1000
1500
2000
Speed (rpm)
Model
K3VL
Page
23.64
Data Sheet
P-1002/01.06
250 bar
300 bar
320 bar
2500
3000
Industrial Products
Pumps
Bearing Life (Full Displacement) (continued)
K3VL200
Note: Service and other life factors have unity value
10,000,000
1,000,000
50 bar
100 bar
150 bar
200 bar
250 bar
300 bar
320 bar
100,000
10,000
1,000
500
1000
1500
2000
Speed (rpm)
Model
K3VL
Page
24.64
Data Sheet
P-1002/01.06
2500
Industrial Products
Pumps
Bearing Life (Industrial situation)
K3VL45
Note: Service and other life factors have unity value
1,000,000
1000 rpm
1200 rpm
100,000
1500 rpm
1800 rpm
10,000
1,000
1
10
100
K3VL80
Note: Service and other life factors have unity value
1,000,000
1000 rpm
100,000
1200 rpm
1500 rpm
1800 rpm
10,000
1,000
1
10
100
Model
K3VL
Page
25.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Bearing Life (Industrial Situation) (continued)
K3VL112
Note: Service and other life factors have unity value
1,000,000
1000 rpm
1200 rpm
100,000
1500 rpm
10,000
1,000
1800 rpm
10
100
K3VL140
Note: Service and other life factors have unity value
1,000,000
1000 rpm
1200 rpm
100,000
1500 rpm
10,000
1800 rpm
1,000
1
10
100
Model
K3VL
Page
26.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Bearing Life (Industrial Situation) (continued)
K3VL200
Note: Service and other life factors have unity value
1,000,000
100,000
1000 rpm
1500 rpm
1200 rpm
10,000
1800 rpm
1,000
10
100
1000
Model
K3VL
Page
27.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Bearing Life (continued)
Bearing Life Correction Factors for Partial Displacement
1200%
1000%
800%
600%
400%
260%
200%
0%
50%
60%
70%
75%
80%
90%
100%
Displacement (%)
All bearing life curves on the previous pages refer to L10 life at full displacement. The foregoing curve is
therefore to be used where duty cycle considerations require one to compute weighted life, which include
partial displacement conditions.
For example as shown above if the bearing life at full displacement from the previous graphs was say
50,000 hours, then at the same operating condition with only 75% displacement the bearing life would be
260% of 50,000 hours or 130,000 hours.
Model
K3VL
Page
28.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Radial Loading Capacity
No axial shaft loading possible
Radial loading is achievable but in specific orientation:-
In addition because of the high bearing capacity of this front bearing, radial shaft loading can be allowed
provided that its orientation is such that it is this front bearing that takes the additional load (See diagram
below and the bearing life and radial loading curves).
acceptable
not acceptable
Model
K3VL
Page
29.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Radial Loading Capacity (continued)
K3VL45 Radial Loading Capacity
100%
80%
60%
40%
20%
0%
1
500
1000
1500
100%
80%
60%
40%
20%
0%
1
500
1000
Model
K3VL
Page
30.64
Data Sheet
P-1002/01.06
1500
1900
Industrial Products
Pumps
Radial Loading Capacity (continued)
K3VL112 Radial Loading Capacity
100%
80%
60%
40%
20%
0%
1
500
1000
1500
2000
2500
2800
2000
2500
2800
100%
80%
60%
40%
20%
0%
1
500
1000
1500
Model
K3VL
Page
31.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Radial Loading Capacity (continued)
K3VL200 Radial Loading Capacity
100%
80%
60%
40%
20%
0%
1
500
1000
1500
2000
2500
3000
3500
4000
Model
K3VL
Page
32.64
Data Sheet
P-1002/01.06
4500
5000
Industrial Products
Pumps
Functional Description of Regulator
Key to Hydraulic Circuit Annotations
Annotation
Note:
Description
A1
A2
a1
a2
B2
B1
Dr
Drain
Pi
Pilot pressure
Pc
Pi
PL
Psv
Ps
Inlet pressure
The optional attached gear pump is recommended for all displacement control options. Hydraulic
circuit diagrams illustrate the attached gear pump.
Regulator Code
Control Curves
PL
Model
K3VL
Hydraulic Circuit
Differential
Pressure Spool
R4
R1
Cut-off
Pressure Spool
T air
Dr B
Page
33.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Functional Description of Regulator (continued)
Regulator Code
Control Curves
Hydraulic Circuit
PL
R3
Differential
Pressure Spool
R1
Unloading
Solenoid
Valve
Cut-off
Pressure Spool
T air
Dr
PL
R3
Differential
Pressure Spool
R1
Cut-off
Pressure Spool
Proportional
Relief
Valve
T air
Dr
Model
K3VL
Page
34.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Functional Description of Regulator (continued)
Regulator Code
Control Curves
Hydraulic Circuit
Differential
Pressure Spool
R4
R1
Cut-off
Pressure
Spool
T air
Dr
PO Pressure Cut-off
PL
R2
Differential
Pressure Spool
R1
Cut-off
Pressure Spool
T air
Dr
PL
R2
Differential
Pressure Spool
Cut-off
R1 Pressure Spool
Cut-off
Solenoid
Valve
A
T air
Dr B
Model
K3VL
Page
35.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Functional Description of Regulator (continued)
Regulator Code
Control Curves
Hydraulic Circuit
PL
R2
Differential
Pressure Spool
R1
Proportional
Relief
Valve
Cut-off
Pressure Spool
T air
Dr
Torque Spool
Limiter
PC
R2
Differential
Pressure Spool
Delivery Pressure
R1
Cut-off
Pressure
Spool
T air
Dr
Model
K3VL
Page
36.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Functional Description of Regulator (continued)
Regulator Code
Control Curves
Hydraulic Circuit
Qmin
360
600
Qmax
PSV
PC
Qmin
0
28
A
Dr
Model
K3VL
Page
37.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Functional Description of Regulator (continued)
Regulator Code
Hydraulic circuit
Parallel control
(Without torque limiter)
/1-PP Parallel pressure
compensation control
Customer
Supply
Pd
PC
Pd
PC
R2
R2
Differential
Pressure
Spool
R1
Differential
Pressure
Spool
R1
Cut-off
Pressure
Spool
Cut-off
Pressure
Spool
T air
T air
Dr
Model
K3VL
Page
38.64
Data Sheet
P-1002/01.06
Dr
Industrial Products
Pumps
Torque Limiter Settings
The following tabulations show the power limitation at various electric motor speeds for a specific pump.
When selecting a control setting please ensure that the power limitation of a particularly sized electric
motor to your national standard is not exceeded.
970 rpm
Power
(KW)
5.5
7.5
11
15
18.5
22
30
37
45
45
L3
L1
M1
H3
1150 rpm
L3
M4
M2
H4
H2
140
L6
L3
L1
M2
H4
H2
Power
(KW)
7.5
11
15
18.5
22
30
37
45
55
1450 rpm
Power
(KW)
7.5
11
15
18.5
22
30
37
45
55
75
45
L4
L1
M2
H4
H3
L4
L3
M3
M1
H4
H2
140
L6
L2
M3
M2
H4
H1
K3VL200
KW
3.7
5.5
7.5
11
15
22
30
37
45
55
75
90
110
132
Model
K3VL
970
L4
L2
M3
M1
H5
H1
1150
L3
L1
M3
M1
H3
H1
L4
L1
M3
M1
H2
L4
L2
M4
M1
H3
H2
140
L5
L3
M3
M1
H4
H2
1750 rpm
45
L2
M3
H4
H2
1450
L3
L2
M3
H6
H4
H2
Page
39.64
1750
Power
(KW)
11
15
18.5
22
30
37
45
55
75
90
45
L2
M4
M2
H4
H1
L4
L1
M3
M1
H4
H1
L3
L2
M2
H6
H4
H2
Data Sheet
P-1002/01.06
140
L4
L2
M3
M2
H3
H1
Industrial Products
Pumps
Installation
Recommended Pump Mounting
The pump should be mounted horizontally with the case drain piping initially rising above the level of the
pump before continuing to the tank as shown in the illustration below. Do not connect the drain line to the
suction line.
The uppermost drain port should be used and the drain piping should be equal or larger in size than the
drain port to minimise pressure in the pump case. The pump case pressure should not exceed 1 bar as
shown in the illustration below. (Peak pressure should never exceed 4 bar.)
4 bar
(peak)
P
0.1 sec
1 bar
(normal)
within 1m
200mm
minimum
depth
200mm
minimum
depth
Drain line
"Goose neck" configuration is required, this prevents direct drop of oil level in the pump case.
Cautions
A)
B)
200mm
minimum depth
Model
K3VL
C)
Page
40.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Installation (continued)
Mounting the Pump Vertically (shaft up)
For applications requiring vertical installation (shaft up) please remove the air bleed plug and connect
piping as shown in the illustration below.
The oil level in the tank should be higher than the pump-mounting flange as shown in illustration [a]
below. If the oil level in the tank is lower than the pump mounting flange then forced lubrication is
required through the air bleed port 1 ~ 2 l/min.
When installing the pump in the tank and submerged in the oil, open the drain port and air bleed port to
provide adequate lubrication to the internal components.
When installing the pump outside the tank run piping for the drain and air bleed ports to tank (see
illustration [c]). If the drain or air bleed piping rise above the level of oil (see illustration [b]) fill the lines
with oil before operation.
oil
air bleeder
plug port
oil
Dr
Dr
drain port
check valve
cracking pressure
0.1 bar
Dr
[c]
[b]
A check valve with cracking pressure of 0.1 bar should be fitted to the case drain line as shown.
Recommended Kawasaki check valves are as follows: (refer to Kawasaki industrial valve
information - data sheet C1001)
Model
K3VL
Model
K3VL45
C10G 10/01-*
K3VL80
C15G 10/01-*
K3VL112
C15G 10/01-*
K3VL140
C15G 10/01-*
K3VL200
C15G 10/01-*
Page
41.64
Data Sheet
P-1002/01.06
Dr
Industrial Products
Pumps
Drive Shaft Coupling
Use a flexible coupling to connect the pump shaft to an engine flywheel or electric motor shaft. Alignment
should be within 0.05mm TIR as shown in the illustration below.
Do not apply any radial or axial loading to the pump shaft. For applications where radial or side loads exist
please contact Kawasaki Precision Machinery (UK) Ltd. for recommendations.
Do not force the coupling on or off the pump shaft. Use the threaded hole in the end of the pump shaft to
fix or remove the coupling.
datums
datums
For engine drives a split type pinch bolt drive flange and flexible coupling is recommended.
Through Drive Limitations
Apart from predefined maximum throughput limitations, one must also ensure that to prevent a possible
excessive bending moment occurring that the maximum combined bending moment of the combination is
not exceeded as determined in the following expression
LP2
LA1
LP1
LA2
L2
mP1
mP2
mA1
L1
LA1'
LP2'
LA2'
LP3'
Bending Moment
Model
K3VL
mP3
mA2
MPX
LPX
Lx
MAX
LAX
=
=
=
=
=
L3
L2
Page
42.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Through Drive Limitations (continued)
Pump overall length [mm] (Lp)
Single
Stock
Pump
Pump
Pump
Size
Type "0"
Type "S"
45/60
244
244
80
272
272
112/140
308
308
220
359
359
Pump
Size
Maximum Permisable
Bending Moment (Nm)
45/60
80
112/140
200
137
244
462
930
(La)
Width
(Lax)
0
20
0
20
24.5
0
25
30
43
6
25
30
38
38
Model
K3VL
:
:
:
:
:
:
50 bar
If higher pressure required contact KPM
10 l/min
Mineral oil
-20~+90C
5~500 cst
NAS grade 10 and below
:
:
:
:
:
700 mA
80 Hz / 200 mAp-p
17.5 (at 20C)
-30~+80C
According to JIS D 0203 S2
Page
43.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions
K3VL45 Installation
K3VL45 with Cut-Off / Load Sense Control
& Torque Limit Module (Clockwise Rotation)
Note
for counter clockwise rotation,
the suction port "B" and the
delivery port "A" are reversed
119
6.5
PL (PC)
154
Dr
89
80
99
165
70
55
A
PL (PC)
70
80
73
160
Adjustment screw for
differential pressure
PL (PC)
45
26.2 0.2
Dr
91
184
See Port
Details
35.7 0.2
184
218
Model
K3VL
Page
44.64
Data Sheet
P-1002/01.06
Dr
13
91
.3
14
See Port
Details
Tair
69.8 0.2
Tair
90
52.4 0.2
Dr
Dr
38
45
25
PL (PC)
.3
14
40
144
PL (PC)
40
Dr
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL45 Mounting Flange and Shaft Options
SAE Type
ISO Type
Flange
ISO 3019/2-100A2HW
0
100h8 -0.054
0
101.6h7-0.035
9 +0.5
0
14
0
46
52
28.10.13
24.981
33
0
25.4 -0.05
38
63.5 +0.03
0
14
6
9.7
M8
SAE "BB" Straight Shaft
SAE J744-25-1
19
25
0
8 -0.036
25j6 +0.009
-0.004
0
28 -0.3
42
36
M8
Shaft end
ISO 3019/2-G25N 19
25
Model
K3VL
Page
45.64
Data Sheet
P-1002/01.06
38
32
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL45 Rear Port
9.10 (231)
10.9 (277)
4-1/2-13UNC-2B
depth 22(0.87)
In case of
( K3VL45/B-1RR
S)
S
K
144(5.67)
38 (1.50)
69.80.3
(2.75 0.012)
Tair
2.87 (73)
3.50 (89)
S
K
73(2.87)
In case of
( K3VL45/B-1RR
S)
9.2(0.36)
Identificate marking
(UNC screw)
26.20.3
(1.03 0.012)
PL/Pc
Dr
119(4.69)
24(0.94)
8(0.31) PL/Pc
25 (0.98)
4-3/8-16UNC-2B
depth 18(0.71)
In case of
( K3VL45/B-1RR
S)
S
K
35.70.3
(1.41 0.012)
4-M12
depth 20(0.79)
52.40.3
(2.06 0.012)
44(1.73)
58(2.28)
90(3.54)
80(3.15)
4-M10
depth 17(0.67)
In case of
( K3VL45/B-1RR
M)
In case of
( K3VL45/B-1RR
M)
S
K
Port Name
Port Size
Tightening
Torque
(Nm)
Flange Threads
Delivery Port
57
3/8-16UNC-2B x 18mm
Suction Port
98
1/2-13UNC-2B x 22mm
Delivery Port
57
M10 x 17
Suction Port
98
M12 x 20
Port Size
Tightening
Torque
(Nm)
Auxiliary Ports
Des.
Port Name
PL
PC
Tair
98
12
12
98
PL
PC
25
Tair
25
Model
K3VL
Page
46.64
Data Sheet
P-1002/01.06
S
K
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL45 Through Drive Options
Dr
SAE "A" 30 Involute Spline
SAE J744-16-4 9T 16/32 DP
244
45
Tair
82.55 +0.050
+0.020
1
06
6 - M10
Depth 17
8
30
Dr
SAE "B" 30 Involute Spline
SAE J744-22-2 13T 16/32 DP
264
101.6 +0.035
0
Tair
45
1
46
4 - M12
Depth 20
11
47
101.6 +0.035
0
Tair
45
1
46
Dr
SAE "BB" 30Involute Spline
SAE J744-25-2 15T 16/32 DP
264
Model
K3VL
Page
47.64
11
47
4 - M12
Depth 20
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL45 Adaptor Kits
402
317
116
116
743
743
742
314
743
415
Cover Kit
SAE "A"
T/D Kit
No
Part Name
T/D Kit
743
SAE "B"
T/D Kit
SAE "BB"
T/D Kit
QTY
Cover Kit
29L8TN
29L4TA
29L4TB
29L4T2
O-Ring
00RBG85
00RBG85
00RBG85
00RBG85
742
O-Ring
00RBG105
00RBG105
415
0SBM825
0SBM825
402
0SBM1020
317
Subplate
314
Cover
2923150-0316
116
Coupling
Model
K3VL
Page
48.64
2924750-0358 2924750-0358
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL80 Installation
K3VL80 with Cut-Off / Load Sense Control
& Torque Limit Module (Clockwise Rotation)
Note
for counter clockwise rotation,
the suction port "B" and the
delivery port "A" are reversed
PL (PC)
79
182
62
164
A
Dr
85
99
98
PL(PC)
79
91
85
181
Dr
PL (PC)
PL (PC)
PL (PC)
Page
49.64
77.8 0.3
35
95
50
Dr
18
95
.5
17
Model
K3VL
26.2 0.2
217
Dr
45
See Port
Details
Tair
35
Tair
Dr
114
52.4 0.2
Dr
A
45
155
.5
17
25
Data Sheet
P-1002/01.06
42.9 0.3
217
260
See Port
Details
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL80 Mounting Flange and Shaft Options
SAE Type
ISO Type
Flange
ISO 3019/2-125A2HW
0
127 -0.05
0
125h8 -0.063
9 +0.5
0
18
0
56
68
0
35.2 -0.03
48
31.224
43
M8
SAE "C" Straight Shaft
SAE J744-32-1
19
25
0
10h9 -0.036
32k6 +0.018
-0.002
0
35 -0.3
50
M12
Shaft end ISO 3019/2-G32N
28
38
Model
K3VL
7.94 +0.002
0
1
81
0
12.7-0.5
Page
50.64
Data Sheet
P-1002/01.06
48
44
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL80 Rear Port Option
119(4.69)
24(0.94)
8(0.31)
PL/Pc
Dr 25 (0.98)
A
79
91(3.58)
4-3/8-16UNC-2B
depth 18(0.71)
4-1/2-13UNC-2B
depth 22(0.87)
239
26.20.3
(1.03 0.012)
169(6.65)
50
(1.97)
77.80.3
(3.06 0.012)
98
Tair
Dr
9.2
(0.36)
S
K
PL (Pc)
In case of
( K3VL80/B-1RR
S)
42.90.3
(1.690.012)
56.5(2.22)
95(3.74)
52.40.3
(2.06 0.012)
54(2.13)
90(3.54)
S
K
In case of
( K3VL80/B-1RR
S)
S
K
4-M10
depth 17(0.67)
In case of
( K3VL80/B-1RR
M)
S
K
4-M12
depth 20(0.79)
In case of
( K3VL80/B-1RR
M)
S
K
Port Name
Port Size
Tightening
Torque
(Nm)
Flange Threads
Delivery Port
57
3/8-16UNC-2B x 18mm
Suction Port
98
1/2-13UNC-2B x 22mm
Delivery Port
57
M10 x 17
Suction Port
98
M12 x 20
Port Size
Tightening
Torque
(Nm)
Auxiliary Ports
Des.
Port Name
PL
PC
Tair
98
12
12
98
PL
PC
25
Tair
25
Model
K3VL
Page
51.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL80 Through Drive Options
1
06
Dr
272
SAE "A" 30 Involute Spline
SAE J744-16-4 9T 16/32 DP
6 - M10
Depth 17
8
33
PL(Pc)
101.6 +0.035
0
45
82.55 +0.035
0
45
Tair
Tair
14
6
292
PL(Pc)
14
6
Dr
11
292
SAE "BB" 30 Involute Spline
SAE J744-25-4 15T 16/32 DP
47
4 - M12
Depth 20
PL(Pc)
Tair
Dr
Tair
101.6 +0.035
0
45
4 - M12
Depth 20
14
53
296.5
18
1
4 - M16
Depth 24.5
Model
K3VL
Page
52.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL80 Adaptor Kits
402
317
116
116
743
743
742
415
314
743
Cover Kit
No
Part Name
T/D Kit
743
SAE "A"
T/D Kit
SAE "A"
T/D Kit
SAE "B"
T/D Kit
SAE "BB"
T/D Kit
SAE "C"
T/D Kit
QTY
Cover Kit
29L8TN
29L8TA
29L8TB
29L8T2
29L8TC
O-Ring
00RBG85
00RBG85
00RBG85
00RBG85
00RBG85
742
O-Ring
00RBG105
00RBG105
00RBG130
415
0SBM1025
0SBM1025
0SBM1030
402
0SBM1020
317
Subplate
314
Cover
2923150-0316
116
Coupling
Model
K3VL
Page
53.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 Installation
K3VL112/140 with Cut-Off / Load Sense Control
& Torque Limit Module (Clockwise Rotation)
Note
for counter clockwise rotation,
the suction port "B" and the
delivery port "A" are reversed
152
19
PL (PC)
77
152
A
224
Dr
Tair
100
80
100
124
125
PL(PC)
Dr
PL (PC)
PL (PC)
See Port
Details
31.8 0.3
250
Model
K3VL
Dr
106.5
103
113.3
Page
54.64
98.5
103
113.3
Tair
Dr
50.8 0.3
22
106.5
Data Sheet
P-1002/01.06
30
30
Tair
200
140
66.7 0.3
Dr
Dr
250
63
77.8 0.3
32
See Port
Details
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 (SAE D 4 BOLT) Mounting Flange & Shaft Options
ISO Type
Flange
ISO 3019/2
2
24
0
12.7-0.5
161.6
0
180h8 -0.063
45
0
152.4h7 -0.063
161.6
4-18 through
9
92
75
44.447
49.3 0.13
60
67
11.11+0.030
+0.015
67
0
44.45h7 -0.025
7/16-14UNC-2B
SAE "D" 30 Involute Spline Shaft
SAE J744-44-4 13T 8/16 DP
0
14h9 -0.043
80
48.5
45k6 +0.018
-0.002
1.5
M16
Shaft end ISO 3019/2
36
48
Model
K3VL
Page
55.64
Data Sheet
P-1002/01.06
63
Industrial Products
Pumps
Unit Dimensions (continued)
88.90.3
3.50 0.012)
Dr
A
B
95(3.74)
Tair
64(2.52)
282(11.10)
31.80.3
(1.25 0.012)
125(4.92)
Dr
Dr
4-M14
depth 19(0.75)
4-M12
depth 22(0.87)
32(1.26)
50.80.3
(2.000.012)
66.70.3
(2.63 0.012)
62(2.44) 55(2.17)
106.5(4.19)
103.5(4.07)
Port Name
Port Size
Tightening
Torque
(Nm)
Flange Threads
Delivery Port
98
1/2-13UNC-2B x 22mm
Suction Port
98
1/2-13UNC-2B x 22mm
Delivery Port
157
M14 x 19
Suction Port
98
M12 x 17
Port Size
Tightening
Torque
(Nm)
Auxiliary Ports
Des.
Port Name
SAE Version ("S", "K", "C", "R", "U", "X" or "T" in position 8 of model)
Dr
PL
PC
Tair
167
12
12
167
PL
PC
25
Tair
25
Model
K3VL
Page
56.64
197.5(7.78)
220(8.66)
152(5.98)
124(4.88)
30(1.18)
10(0.39) PL(P c)
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 (2 Bolt) Installation
152
124
30
10
218
A
197.5
204
224
Dr
A
B
Dr
100
124
91
PL (PC)
157.6
134.5
Dr
31.8 0.3
280
136.5
81
Dr
17.5
Dr
3
2
66.7 0.3
30
PL (PC)
17.5
100
181 Tair
Tair
103
113.3
103
113.3
10
125
90(3.54)
208
6
3
Dr
Tair
20
48
136.5
50.8 0.3
280
326
Model
K3VL
Page
57.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 Mounting Flange (2 Bolt) and Shaft Options
0
12.7 -0.5
1
81
0
12.7-0.5
56
31.224
43
M8
SAE "C" Straight Shaft
SAE J744-32-1
19
25
54
38.1
43
SAE "CC" 30
Involute Spline Shaft
SAE J744-38-4
17T 12/24 DP
62
Model
K3VL
7.94 +0.022
0
0
35.2 -0.3
48
0
31.75h7 -0.025
Page
58.64
Data Sheet
P-1002/01.06
48
44
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 Through Drive Options
Tair
11
53
14
6
6 - M12
Depth 25
B
Tair
Dr
14
337.5
SAE "CC" 30 Involute Spline
SAE J744-38-4 17T 12/24 DP
59
Dr
1
81
6 - M16
Depth 30
14
58
337.5
45
127 +0.035
0
Tair
6 - M12
11
Depth 17
53
SAE "B" 30 Involute Spline
SAE J744-22-4 13T 16/32 DP
45
332.5
SAE "BB" 30 Involute Spline
SAE J744-25-4 15T 16/32 DP
332.5
14
6
127 +0.035
0
Dr
Dr
45
101.6 +0.035
0
Tair
101.6
45
+0.035
0
6 - M10
Depth 17
8
31
307.5
1
46
6 - M16
Depth 30
Tair
Dr
15
71
350.5
161.6 0.2
45
1
06
152.4 +0.035
0
Dr
45
Tair
82.55 +0.035
0
4 - M16 Depth 43
161.6 0.2
Model
K3VL
Page
59.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL112/140 Adaptor Kits
402
317
116
116
314
743
743
742
743
415
Cover Kit
317
317
317
317
116
116
116
116
743
742
743
742
743
742
743
742
415
415
415
415
No
Part Name
T/D Kit
743
742
415
402
317
314
116
O-Ring
O-Ring
Screw Hex SHC
Screw Hex SHC
Subplate
Cover
Coupling
Model
K3VL
SAE "BB"
T/D Kit
QTY
Cover Kit
29L8TN
29LHTA
29LHTB
29LHT2
1
1
4
2
1
1
1
00RBG85
0SBM1020
2923150-0316
00RBG85
2903150-0268
00RBG85
00RBG105
0SBM1230
2924750-0360
2903150-0269
00RBG85
00RBG105
0SBM1230
2924750-0360
2903150-0270
No
Part Name
T/D Kit
743
742
415
O-Ring
O-Ring
Screw Hex SHC
Screw Hex SHC
Subplate
Cover
Coupling
317
314
116
Page
60.64
QTY
SAE "C"
T/D Kit
SAE "CC"
T/D Kit
29LHTC
29LHT3
29LHTD
1
1
4
2
1
1
1
00RBG85
00RBG130
0SBM1235
2924750-0361
2903150-0271
00RBG85
00RBG130
0SBM1235
2924750-0361
2903150-0272
00RBG85
00RBG150
0SBM1250
2924750-0362
2903150-0273
Data Sheet
P-1002/01.06
SAE "D"
T/D Kit
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL200 Installation
Model
K3VL
Page
61.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
K3VL200
No
Part Name
T/D Kit
116
2903150-0761
317
2924750-0674
407
SHCS
0SBM825
712
00RBG85
742
00RBG85
No
Part Name
T/D Kit
116
317
QTY
QTY
SAE "A"
29LKTA
SAE "B"
SAE "C"
SAE "D"
SAE "E"
29LKTB
29LKTC
LKTD
29LKTE
2903150-0762
2903150-0763
2903150-0764
2903150-0764
2924750-0675
2924750-0667
2924750-0677
2924750-0686
407
SHCS
0SBM1230
0SBM1230
0SBM1245
0SBM1245
712
O-Ring
00RBG120
00RBG125
00RBG125
00RBG125
742
O-Ring
00RBG105
00RBG130
PCPP155
PCPP170
Tightening
Torque
(Nm)
Flange Threads
Port Name
Port Size
Delivery Port
235
5/8-11UNC-2B
Suction Port
235
5/8-11UNC-2B
Delivery Port
235
M16
Suction Port
235
M16
Port Size
Tightening
Torque
(Nm)
Auxiliary Ports
Des.
Port Name
PL
PC
Tair
Model
K3VL
Page
62.64
167
12
12
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
Electrical Displacement Control
G
F
PSV
PSV
PC
K3VL45
21
52
90
187
157
226
210
K3VL80
25
59
83
202
172
233
217
K3VL112/140
38
64
78
244
214
247
231
Model
K3VL
Page
63.64
Data Sheet
P-1002/01.06
Industrial Products
Pumps
Unit Dimensions (continued)
Unloading valve module (*N)
K3VL45
K3VL80
K3VL112/140
K3VL200
169
169
202
212
155
166
190
205
K3VL45
K3VL80
K3VL112/140
K3VL200
179
179
212
222
233
244
280
295
A: Distance between the centre line of the pump and the top of the bolt head for the cut off regulator.
B: Distance between the centre line of the pump and top of the solenoid valve.
Page
64.64
Data Sheet
P-1002/01.06