Al Welding

About The Lincoln Electric Company
............................................................................................................................................................
Lincoln Electric is the worlds leading manufacturer of welding equipment and

consumables. Our focus is on helping companies make their welding operations
more effective, more efficient and more profitable.
We are dedicated to two equally important goals: exceptional quality and
exceptional service. Our field support team with hundreds of field sales
engineers and thousands of knowledgeable and responsive Lincoln Electric
distributors in countries all over the world is the largest in the industry.
Innovative thinking. A service-first attitude. Fresh approaches to design,
manufacturing and packaging. Worldwide strength.
THATS LINCOLN ELECTRIC.
| www.lincolnelectric.com
Lincoln Electrics SuperGlaze Technology
............................................................................................................................................................
Sample defect from spool of competitive product
SuperGlaze Best in Class
For superior welding performance, turn to SuperGlaze aluminum MIG wire from
Lincoln Electric. SuperGlaze prevents the problems usually associated with
aluminum wire feeding, such as birdnesting, tangling and burnback, to provide a
stable arc, great feedability and exceptional control every time you weld! The keys
are SuperGlazes smooth surface finish and consistent chemical composition. What
this means for you is a product that produces high quality, exceptionally
productive welds.
LET US PUT OUR EXPERIENCE TO WORK FOR YOU

As a major supplier of welding wire, Lincoln Electric is the leader in MIG wire
manufacturing technology. We carry that same technology and expertise to our
aluminum MIG wire manufacturing. Lincoln Electric has the only fully integrated
aluminum MIG wire facility in the world. We start from raw primary aluminum
and then use state-of-the-art equipment to produce a complete range of aluminum
alloys including 1100, 1070, 2319, 4043, 4047, 5087, 5183, 5356, 5554 and 5556. This
gives us full control of welding chemistry throughout the process as well as the
ability to always deliver product to our customer, regardless of market conditions.
www.lincolnelectric.com | 3
Lincoln Electrics SuperGlaze Technology
............................................................................................................................................................
WHAT MAKES SUPERGLAZE STAND OUT FROM THE REST?

Three unique features:
1. A manufacturing process that precisely controls the alloy chemical composition
to produce consistent physical characteristics.
2. A proprietary process that gives SuperGlaze a superior surface finish for optimum
surface integrity.
3. A technical services team with years of experience dedicated to
aluminum welding.
What all this means to you is outstanding welding characteristics, spool to spool,
time after time. Lincoln Electrics aluminum MIG wire combined with our advanced
MIG welding equipment and help from our technical services team makes
aluminum as easy to weld as any other material.
4 | www.lincolnelectric.com
Contents
............................................................................................................................................................
About The Lincoln Electric Company ................................................................................ 2

Lincoln Electrics SuperGlaze Technology ....................................................................... 3
Let Us Put Our Experience to Work for You ....................................................................... 3
What Makes SuperGlaze Stand Out From the Rest? ....................................................... 4
Section 1 Introduction ......................................................................................................... 7
1.1 Welding Aluminum Vs. Welding Steel .................................................................... 8
1.2 Metallurgy .................................................................................................................. 8
1.2.1 Aluminum Alloys ....................................................................................................... 9
1.2.2 Wrought Alloys .......................................................................................................... 9
1.2.3 Cast Alloys ................................................................................................................ 10
1.3 Alloying Elements ................................................................................................... 10
1.4 Temper Designations .............................................................................................. 12
1.4.1 Nonheat-treatable Alloys Strain-Hardened Designations ............................ 12
1.4.2 Heat-treatable Alloys .............................................................................................. 14
Section 2 Effects of Welding on Aluminum Alloys ........................................................ 15
2.1 Nonheat-treatable Alloys ....................................................................................... 15
2.2 Heat-treatable Alloys .............................................................................................. 15
Section 3 Filler Metal Selection ........................................................................................ 18
3.1 Aluminum Filler Alloys ........................................................................................... 18
Section 4 Welding Preparation ......................................................................................... 25
4.1 Storage of Aluminum and Aluminum Wire Prior to Welding ............................ 25
4.2 Welding Preparation ............................................................................................... 26
4.3 Pre-weld Cleaning ................................................................................................... 28
4.4 Interpass Cleaning .................................................................................................. 29
4.5 Backgouging ............................................................................................................. 29
Section 5 GMAW of Aluminum Alloys ............................................................................ 31
5.1 Properties of Aluminum ......................................................................................... 31
5.2 Modes of Metal Transfer ......................................................................................... 31
5.3 Power Supplies and Wire Drives ............................................................................ 38
5.4 GMAW-P Power Supplies ........................................................................................ 38
5.5 Weld Mode Searching ............................................................................................. 39
5.6 Wire Drives and Controls ....................................................................................... 44
5.7 Aluminum Feeding Enhancements ...................................................................... 46
5.8 Shielding Gas ........................................................................................................... 47
5.9 Welding Techniques ................................................................................................ 48
Section 6 Weld Defects Causes and Cures ..................................................................... 51
Appendix A | Welding Safety Instructions ..................................................................... 68
.............
Section 1
Introduction
The use of aluminum as a structural material is fairly recent. In fact, when the
Washington Monument was completed in December 1884, it was capped with
a 100 oz. pyramid of pure aluminum because aluminum was considered a
precious metal.
Aluminum was not widely used at that time because it is a reactive metal. It is
never found in its elemental state in nature. Instead, it is always tightly bound with
oxygen as aluminum oxide (Al2O3), also known as bauxite ore. Although bauxite
ore is plentiful, a direct reduction method to produce aluminum from bauxite has
yet to be discovered. It was only in 1886, when the American Charles M. Hall and
the Frenchman Paul Heroult almost simultaneously (but independently) discovered
electrolytic processes for obtaining pure aluminum from aluminum oxide, that
aluminum became available in commercial quantities. The processes discovered by
Hall and Heroult are still used today, with some modifications. The massive
amount of electrical power required to produce aluminum is the main reason for
its higher cost relative to steel.
Aluminum is wideley used in numerous applications:
It conducts electricity and heat almost as well as copper.
It is widely used in electrical bus bars and other conductors, heat exchangers of
all kinds, and cookware.
It becomes stronger rather than brittle with decreasing temperature, so it has
found wide application in cryogenic equipment at temperatures as low as
-452F (-269C).
It is very corrosion resistant in most environments, so it has found wide
applications in marine and chemical environments.
The characteristics of aluminum alloys that make them attractive as structural
materials are their light weight (one third the weight of steel for equal
volumes) and their relatively high strength (equal in many cases to that of
construction steel grades). This combination has resulted in increased use of
aluminum alloys in applications such as passenger automobiles, trucks,
over-the-road trailers and railroad cars. Additionally, the structure of most
aircraft is fabricated mainly from aluminum alloys, although pieces are most
often joined by riveting in these applications.
Introduction
............................................................................................................................................................
1.1 WELDING ALUMINUM VS. WELDING STEEL

We often approach welding of aluminum as if it is just shiny steel. Most welders
begin by learning how to weld steel, with some moving on to welding aluminum.
Most welding equipment is designed to weld steel, with welding of aluminum alloys
being an afterthought (this has begun to change).
However, the differences between steel and aluminum mean that you need a
specialized approach to welding of aluminum. The balance of this guide will
discuss the main differences between welding of aluminum and welding of
steel and how to address them.
THE DIFFERENCES BETWEEN WELDING STEEL AND WELDING ALUMINUM CAN BE SUMMED UP IN
THREE STATEMENTS:
1. Almost all steels are weldable if you take enough care. There are some aluminum
alloys that are just not arc weldable. Fabricators fall into this trap regularly. Well
discuss the weldability of the various alloy families in detail. At this point, lets just
say that many aluminum alloys, especially the stronger ones, are not weldable.
2. All steels are heat-treatable. Some aluminum alloys are heat-treatable, but some
are not. Even for the heat-treatable aluminum alloys, the heat treatments are
totally different from those used for steel. In fact, if you heat up some alloys
and quench them, they will become softer instead of harder. Be aware of the
differences and act accordingly.
3. When welding steels, you can almost always make a weld that is as strong as the
parent material. In aluminum alloys, the weld will rarely be as strong as the parent
material. This is usually true for welds in both heat-treatable and nonheat-treatable
alloys. The strength difference between the weld or heat affected zone (HAZ) and
the parent material is often significant, usually 30% or more.
1.2 METALLURGY
To understand aluminum, we must first understand some basics about aluminum
metallurgy. Aluminum can be alloyed with a number of different elements, both
primary and secondary, to provide improved strength, corrosion resistance and
general weldability.
The primary elements that alloy with aluminum are copper, silicon, manganese,
magnesium and zinc. It is important to note that aluminum alloys fall into two
classes: heat-treatable or nonheat-treatable.
Heat-treatable alloys are those that are heat treated to increase their mechanical
properties. To heat treat an alloy means heating it at a high temperature, putting the
Introduction
............................................................................................................................................................
alloying elements into solid solution and then cooling it at a rate that will produce
a super saturated solution. The next step in the process is to keep the solution at a
lower temperature long enough to allow a controlled amount of precipitation of the
alloying elements.
With nonheat-treatable alloys, it is possible to increase strength only through cold
working or strain hardening. To do this, a mechanical deformation must occur in the
metal structure, producing higher strength and lower ductility and therefore resulting
in increased resistance to strain.
1.2.1 ALUMINUM ALLOYS

Just as the American Iron and Steel Institute (AISI) registers steel chemistries and
grades, the Aluminum Association (AA) registers alloy designations, chemistries
and mechanical properties for aluminum alloys. However, the alloy designation
system is totally different from that used for steels. Additionally, different
designation systems are used for wrought and cast alloys.
1.2.2 WROUGHT ALLOYS

Wrought alloy designations use a four digit number plus a temper designation,
which we will discuss later. Aluminum alloys are broken up into eight families
depending on the main alloying elements. The aluminum alloy families are shown
in Table 1-1, along with their heat-treatability.
Table 1-1: Wrought Alloy Designations
Alloy Family
Main Alloying Elements
Heat -treatable
1xxx
Pure Aluminum
No
2xxx
Copper (sometimes with magnesium)
Yes
3xxx
Manganese (sometimes with magnesium)
No
4xxx
Silicon
No
5xxx
Magnesium
No
6xxx
Magnesium plus silicon
Yes
7xxx
Zinc (sometimes with magnesium & copper)
Yes
8xxx
All others
Normally Yes
Note: The designation 2XXX etc is an industry standard abbreviation used to mean all alloys in the 2000 series.
If you have a piece of 6061, its clear that it is a wrought alloy (4 digits), its heattreatable, and it contains magnesium and silicon. The second digit of the four shows
whether the alloy is the first such alloy registered. If this is the case, the second digit
will be 0, as in 5054. Digits other than 0 indicate that the alloy is a modification
of a registered alloy. 5154 would be the first modification of 5054. Alloy 5754 is the
seventh modification. The last two digits are assigned arbitrarily by the Aluminum
Introduction
............................................................................................................................................................
Association when the alloy is registered. Note that the material designation gives
no indication of alloy or weld strength.
1.2.3 CAST ALLOYS

The designation system for cast alloys classified into families is shown in Table 1-2.
The families are somewhat different from the designations for wrought alloys.
These designations have only three digits, followed by a decimal point and one
more digit. For these alloys, the first digit shows the alloy family. The next two
digits are arbitrarily assigned. Alloy modifications are indicated by a letter prefix:
356 would be the original version of an alloy, A356 is the first modification, B356 is
the second modification, etc. The number following the decimal point designates
whether the alloy is produced as a casting of final form or as an ingot for remelting.
Table 1-2: Cast Alloy Designations
Alloy Family
Main Alloying Elements
Heat -treatable
1XX.X
Pure Aluminum
No
2XX.X
Copper (sometimes with magnesium)
Yes
3XX.X
Silicon plus magnesium
Yes
4XX.X
Silicon
Yes
5XX.X
Magnesium
No
6XX.X
Not Used
NA
7XX.X
Zinc
Yes
8XX.X
Tin
No
9XX.X
Other
1.3 ALLOYING ELEMENTS

Pure Aluminum (1XXX series). Contains no alloying elements and is not heattreatable. It is used primarily in chemical tanks and pipe because of its superior
corrosion resistance. This series is also used in electrical bus conductors because of
its excellent electrical conductivity. It is easily welded with 1100 and 4043 filler wires.
Copper (2XXX series) Provides high strength to aluminum. This series is heattreatable and mainly used in aircraft parts, rivets and screw products. Most 2XXX
series alloys are considered poor for arc welding because of their sensitivity to hot
cracking. Most of these alloys should not be welded, however, alloys 2014, 2219 and
2519 are easily welded with 4043 or 2319 filler wire. These three alloys are widely
used in welded fabrication.
Manganese (3XXX series). Yields a nonheat-treatable series used for general-purpose
fabrication and build-up. Moderate in strength, the 3XXX series is used for forming
applications including utility and van trailer sheet. Strain hardening will improve it by
Introduction
............................................................................................................................................................
providing good ductility and improved corrosion properties. Typically welded with 4043 or
5356 filler wire, the 3XXX series is excellent for welding and not prone to hot cracking. Its
moderate strengths prevent this series from being used in structural applications.
Silicon (4XXX series). Silicon reduces the melting point of aluminum and improves
fluidity. Its principal use is as filler metal. The 4XXX series has good weldability and
is considered a nonheat-treatable alloy. Alloy 4047 is often used in the automotive
industry because it is very fluid and good for brazing and welding.
Magnesium (5XXX series). When added to aluminum, magnesium has excellent
weldability, good structural strength and is not prone to hot cracking. In fact, the 5XXX
series has the highest strength of the nonheat-treatable aluminum alloys. It is used for
chemical storage tanks and pressure vessels as well as structural applications, railway
cars, dump trucks and bridges because of its corrosion resistance.
Silicon And Magnesium (6XXX series). This medium strength, heat-treatable series
is primarily used in automotive, pipe, railings and structural extrusion applications.
The 6XXX series is prone to hot cracking, but this problem can be overcome by the
correct choice of joint and filler metal. Can be welded with either 5XXX or 4XXX
series without cracking adequate dilution of the base alloys with selected filler
wire is essential. A 4043 filler wire is the most common for use with this series.
6XXX alloys should never be welded autogenously, as they will crack.
Zinc (7XXX series) Zinc added to aluminum with magnesium and copper
produces the highest strength heat-treatable aluminum alloy. It is primarily used
in the aircraft industry. The weldability of the 7XXX series is compromised in
higher copper grades, as many of these grades are crack sensitive due to wide
melting ranges and low solidus melting temperatures. Grades 7005 and 7039 are
weldable with 5XXX filler wires. They are widely used for bicycle frames and
other extruded applications.
Other (8XXX series). Other elements that are alloyed with aluminum (i.e., lithium)
all fall under this series. Most of these alloys are not commonly welded, though they
offer very good rigidity and are principally used in the aerospace industry. Filler
wire selections for these heat-treatable alloys include the 4XXX series.
In addition to the primary aluminum alloying elements, there are a number of

secondary elements, chromium, iron, zirconium, vanadium, bismuth, nickel and
titanium. These elements combine with aluminum to provide improved corrosion
resistance, increased strength and better heat treatability.
Introduction
............................................................................................................................................................
1.4 TEMPER DESIGNATIONS

The information above allows an aluminum alloy to be recognized by its
chemistry, but not by the heat treatment or mechanical properties. To show these
properties, temper designations are assigned. The complete designation of an
alloy might be 6061-T6 or 5083H114. Most of these designations are different for
heat-treatable and nonheat-treatable alloys; however, two common designations
apply to all alloys:
O Temper (not zero). When an alloy is given this designation, the supplier has
annealed the alloy, typically at 650-750F (343-300C), and it is as soft as possible.
F Temper. When an alloy is supplied in this temper, it is supplied as
fabricated. This means the supplier is guaranteeing that the chemistry of the
material meets the chemical requirements for the specified alloy, but there are
no claims regarding the mechanical properties of the alloy. This temper is often
specified by fabricators who subsequently forge or form the supplied material
and establish mechanical properties by heat treatment after forming.
To discuss the remainder of the temper designations, we need to discuss the
heat-treatable and nonheat-treatable alloys.
1.4.1 NONHEAT-TREATABLE ALLOYS STRAIN-HARDENED DESIGNATIONS

These alloys cannot be strengthened by heat treatment. However, they can be
strengthened by cold working, also called strain hardening. If an aluminum alloy is
deformed at elevated temperatures, 600F (315C) or higher, little or no
strengthening takes place. However, if the alloy is deformed at lower temperatures,
it will gain strength. In general:
The more the alloy is deformed, the stronger it gets. Finally, at some point, the
alloy will have no ductility and will fracture.
The higher the alloy content, the more it will gain strength by being deformed.
Both of these phenomena are shown in Figure 1-1.
Introduction
............................................................................................................................................................
TEMPERS
H32
H12
H34
H14
H36
H16
H38
H18
5086
40
300
5052
30
200
3003
20
MPA
mpa
YIELD STRENGTH (ksi)
50
1100
100
10
0
20
40
60
PERCENT COLD WORK
80
Figure 1-1: Relationship of Yield Strength, Amount of Cold Work and Alloy Content.
The temper designation for strain hardened alloys is usually made up of two digits,
as shown in Table 1-3.
The first digit shows whether the alloy is only strained or whether it has been
partially annealed and/or stabilized. The second digit shows how much strain
hardening has been put into the alloy. Higher numerical values mean higher strain
levels, which means higher yield and tensile strengths.
Table 1-3: H Temper Designations
First Digit Indicates Basic Operations
H1-
Strain Hardened Only
H2-
Strain Hardened and Partially Annealed
H3-
Strain Hardened and Stabilized
Second Digit Indicates Degree of Strain Hardening

HX2-
Quarter Hard
HX4-
Half Hard
HX6
Three-Quarters Hard
HX8-
Full Hard
HX9-
Extra Hard
Introduction
............................................................................................................................................................
1.4.2 HEAT-TREATABLE ALLOYS

Strain hardened H tempers are not used for heat-treatable alloys. Instead, a series
of T tempers that indicate the heat treatment state are used. A total of (10)
tempers exist; T1 through T10. The commonly seen designations are T4 and T6.
Aluminum alloys are heat-treatable because of a phenomenon called precipitation
hardening. They do not harden by a martensitic transformation as steel does. In
precipitation hardening, one metal can be dissolved in another in a solid solution,
and solubility generally increases with temperature. For example, just as sugar will
dissolve in a cup of tea when heated, copper, zinc or combinations of magnesium
and silicon will dissolve in aluminum as it is heated.
When the heat-treatable alloys are heated to approximately 950F (510C) and held
for a few minutes, all the alloying elements are taken into a solution in the solid
aluminum. This is called a solution heat treatment. Normally, the alloy is
quenched in water after this point to arrive at the T4 temper. Although the T4
temper is substantially stronger than the annealed O temper, the primary
purpose of quenching is not strengthening by phase transformation. Instead, the
quenching serves to keep the alloy additions in solution at room temperature. If the
aluminum were cooled slowly from the solution treatment, the alloying additions
would reprecipitate and no strengthening would occur.
The tensile and yield strengths of the material will increase for several weeks after
the heat treatment and can increase significantly in some alloys. After this initial
period, the alloy is stable indefinitely. The customer is generally unaware of this
initial strength increase because the aluminum producer doesnt ship the alloy
until the strength has stabilized.
The T4 temper, while stable, does not give the alloy maximum strength. Most alloys
are sold in a maximum strength T6 temper. To get from T4 to T6 temper, the material
is put in a furnace at a temperature of 325F to 400F (163C to 204C) and allowed
to age 1 to 5 hours. The dissolved alloying elements will form submicroscopic preprecipitates in the material and produce maximum strength. If this aging heat
treatment is carried out at too high a temperature or for too long, the precipitates will
get too large and a lower strength, overaged condition will result.
Note: This final aging heat treatment is carried out at 400F (204C) maximum.
The welding heat, which can heat the surrounding material to well over this
temperature, can significantly degrade the strength of the heat affected zone
(HAZ). This is discussed in more detail on the following page.
.............
Section 2
Effects of Welding on Aluminum Alloys
As before, it is easiest to discuss the effects of welding on the mechanical

properties of aluminum weldments if we discuss nonheat-treatable alloys and
heat-treatable alloys separately.
2.1 NONHEAT-TREATABLE ALLOYS

As was discussed earlier, these alloys can be, and often are, strengthened by cold
working. Cold worked alloys can have yield and tensile strengths twice those of the
annealed O temper alloy. These cold worked alloys can be softened back to the
O temper by annealing at 650-700F (343-371C). Since the heat of welding
produces temperatures considerably higher than this at the weld fusion line, the
result of welding is that the HAZ of welds in nonheat-treatable alloys (i.e., 1XXX,
3XXX, 4XXX, and 5XXX) becomes annealed. Therefore, the strength of the weld joint
is always equal to the strength of the O temper annealed base material, regardless
of what the starting temper of the parent material was. If you weld O temper
material, the weld will be as strong as the starting parent material. If you weld any
material that is strain hardened (i.e., cold worked), the weld will be weaker than the
starting material, perhaps significantly weaker.
The HAZ can never become softer then the O temper, so excess welding heat
input will not make the HAZ softer. It can, however, make the HAZ wider.
Normally, this will not further reduce the strength of the welded joint, although
other problems can arise due to excessive heat input.
From a practical standpoint, there is no way to regain the strength lost during
welding. If the weld is cold worked, it will begin to work harden again. However,
this is not usually a practical industrial solution because, in most cases, the weld
will not be as strong as the starting cold worked material.
2.2 HEAT-TREATABLE ALLOYS

There is no blanket statement that can be made about the welded strength of heattreatable alloys. As previously stated, the weld will generally be weaker than the
parent material. However, the welded properties will strongly depend on the temper
of the material before welding and also on heat treatments performed after
welding. Figure 2-1 shows a micro-hardness trace across a weld, starting at the
center of the weld. The graph actually shows four curves representing what
happens to material in the T4 and T6 tempers in the as-welded (AW) and post-weld
heat-treated (PWA) conditions.
Effects of Welding on Aluminum Alloys
............................................................................................................................................................
Note the following:

1. The HAZ is about 1/2 in. (12.7 mm) wide. The actual width of the HAZ will depend
on a number of things, including the welding process used and the thickness of
the material. HAZ widths of 1 in. (25.4 mm) are not uncommon in thin materials.
2. The hardness and strength of the weldment is typically lowest in the HAZ.
Because of this, strength of the welding filler alloy is not a primary concern when
making butt welds. A weld will most often fail in the HAZ.
3. Unlike nonheat-treatable alloys, the hardness (and therefore strength) in the HAZ
is not always the same. It depends on the material temper prior to welding and
whether the weld is post-weld aged.

a. The weakest HAZ occurs when the material is welded in the T6 temper and
used as-welded.
b. The HAZ, and therefore the weldment, will actually be slightly stronger if the
material is used in the T4 temper and used as welded.
c.

If the weldment in either T4 or T6 material is post-weld aged, the strength of

the HAZ can increase significantly. The exact post-weld heat treatment varies
with the alloy, but aging at around 400F (204C) for about one hour is
generally recommended.
INCHES
0.25
110
0.5
0.75
1.0
HARDNESS (DPH-500 g)
T4 PWA
100
T6 PWA
90
T6 AW
T4 AW
80
70
0.5
1.0
1.5
2.0
DISTANCE FROM FUSION ZONE (cm)

Figure 2-1: Hardness vs Distance for 6061-T4 and T6 in the As-Welded (AW)
and Post-Weld Aged (PWA) Conditions
2.5
Effects Of Welding On Aluminum Alloys
............................................................................................................................................................
When you fabricate using heat-treatable alloys, you have options that are not
available with nonheat-treatable alloys when it comes to recovering some of the
strength lost during welding. For instance, since the 6XXX alloys bend more easily
and around a smaller radius in the T4 temper than in the T6 temper, these alloys
can be bought in the T4 temper, formed easily, welded and then aged. The resulting
mechanical properties will be significantly higher than if the material was
purchased in the T6 temper.
Finally, if the right filler alloy is chosen, the finished weldment can be completely
heat-treated and the T6 properties restored.
Please note that this requires a re-solution heat treatment, quench and re-aging.
This is often practical for small structures, but not for large ones. For example,
aluminum bicycle frames are often fabricated in this way.
The HAZ of welds in heat-treatable alloys is significantly different from the HAZ in
nonheat-treatable alloys. The strength of the HAZ in heat-treatable alloys can be
considerably reduced if excessive heat input is used. Therefore, it is very important
not to use excessive preheats [200F (93C) maximum is recommended], to carefully
monitor interpass temperatures [250F (121C) maximum is recommended], and to
avoid practices such as wide weave passes, which will result in excessive heat input.
.............
Section 3
Filler Metal Selection
3.1 ALUMINUM FILLER ALLOYS

Most common aluminum filler alloys fall into the 4XXX and 5XXX families, with a
few coming from the 1XXX, 2XXX and the casting alloys. The chemical composition
of the common aluminum filler alloys is shown in Table 3-1.
A number of characteristics determine the best filler metal choice for a given base
material or combination of base materials. Among these are::

Freedom from hot cracking

Weld metal ductility
Weld metal corrosion resistance
Weld metal shear strength in fillet and lap joints
Ease of welding (i.e., weldability)
Filler wire feedability
Weld color match with parent metal for applications requiring post-weld anodizing
There are a number of filler metal selection charts that have taken these factors
into account and give good overall recommendations for filler metal selection. A
composite of these charts, which covers most alloy combinations, is shown in Table
3-4 on page 22.
In general, filler alloy recommendations for the various alloy families can be
summarized as follows:
1XXX Alloys These alloys are usually used for their electrical conductivity and/or
corrosion resistance. Their sensitivity to hot cracking is very low. They are usually
welded using 1100 or 1188 fillers, but matching filler metals are also available for
specialized alloys such as 1350. If electrical conductivity of the joint is not of
primary importance, 4043 may be used.
2XXX Alloys Many alloys in this series are not arc weldable. Those that are
include 2219, 2014, 2519, 2008 and 2036. Alloy 2319 is a matching filler alloy for 2219
and 2519 and can also be used on the other weldable alloys. Alloys 4043 and 4145,
which contain copper, can also be used. Alloy 5XXX fillers should not be used to
weld 2XXX parent materials, because cracking will result.
3XXX Alloys These moderate strength aluminummanganese alloys are relatively
crack resistant and can easily be welded using either 4043 or 5356.
............................................................................................................................................................
Table 3-1: Wire Chemical Composition for Common Aluminum Wires

AWS A5.10-99
ASME SFA-5.10
Classification
%Mn
%Si
%Fe
%Mg
%Cr
%Cu
%Ti
%Zn
%Be
%Others (1)
%Al
ER1100 & Alloy 1050
0.05
0.05-0.02
0.10
0.05
99.0
ER2319
0.20-0.40
0.20
0.30
0.02
5.8-6.8
0.10-0.20
0.10
(2)
0.05(3)
Balance
ER4043
0.05
4.5-6.0
.08
0.05
0.30
0.20
0.10
(2)
0.05
Balance
ER4047
0.15
11.0-13.0
0.8
0.10
0.30
0.20
(2)
0.05
Balance
Alloy 5052
0.10
0.25
0.40
2.2-2.8
0.15-0.35
0.10
0.10
(2)
0.05
Balance
Alloy 5056
0.05-0.20
0.30
0.40
4.5-5.6
0.05-0.20
0.10
0.10
(2)
0.05
Balance
Alloy 5154
0.10
0.25
0.40
3.1-3.9
0.15-0.35
0.10
0.20
0.20
(2)
0.05
Balance
ER5183
0.50-1.0
0.40
0.40
4.3-5.2
0.05-0.25
0.10
0.15
0.25
(2)
0.05
Balance
ER5356
0.05-0.20
0.25
0.40
4.5-5.5
0.05-0.20
0.10
0.06-0.20
0.10
(2)
0.05
Balance
ER5554
0.50-1.0
0.25
0.40
2.4-3.0
0.05-0.20
0.10
0.05-0.20
0.25
(2)
0.05
Balance
ER5556
0.50-1.0
0.25
0.40
4.7-5.5
0.05-0.20
0.10
0.05-0.20
0.25
(2)
0.05
Balance
ER5654
0.01
3.1-3.9
0.15-0.35
0.05
0.05-0.15
0.20
(2)
0.05
Balance
NOTE: Single values are maximum, except aluminum.

(1) Total of others shall not exceed 0.15%.
(2) Beryllium shall not exceed 0.0003%.
(3) Vanadium content shall be 0.05 - 0.15% and Zirconium content shall be 0.10 - 0.25%.
4XXX Alloys These alloys are usually found as welding or brazing fillers. In the
rare event you encounter them as parent materials, 4047 is usually the best choice
as a filler metal.
5XXX Alloys These higher strength aluminummagnesium alloys are the most
common structural aluminum sheet and plate alloys. The general rule, except for
the alloy 5052, is to choose a 5XXX filler metal with slightly higher magnesium
content than the parent material being welded. For all alloys except 5052, 5XXX
alloys should not be welded using 4XXX filler alloys. The high Mg content of the
parent material, when combined with the high Si content of the 4XXX fillers, will
result in a high level of Mg2Si a brittle intermetallic compound that will cause the
weld to have poor ductility and toughness. In choosing filler alloys for 5XXX alloys,
there are several specific recommendations:

5052 This alloy has just the right amount of Mg content to exhibit a relatively
high crack sensitivity. If it is welded with 5052 filler alloy, it will often crack.
To avoid the tendency to crack, 5052 is usually welded with a filler alloy of
much higher Mg content, such as 5356. The resulting weld metal, which is an
alloy of the 5356 and 5052, has a Mg content high enough to be crack resistant.
Additionally, the Mg content of 5052 is low enough that it can be successfully
welded using 4043.
............................................................................................................................................................
High Temperature Applications Al-Mg alloys with Mg content over 3%

are unsuitable for service temperatures over 150F (65C) because they are
susceptible to stress corrosion cracking at higher temperatures. This is true for
filler alloys as well and should be taken into account in selecting filler alloys.
5454 This alloy is a lower Mg alloy specifically developed to be immune to the

stress corrosion cracking noted above. Filler alloy 5554 is designed as a matching
filler alloy for 5454 and should be used whenever possible.
5083 and 5456 These high Mg, high strength alloys can be successfully welded
using 5356. However, most structural codes require that welds in these alloys
have a minimum ultimate tensile strength of 40 ksi (276 MPa). When welded
using 5356, welds in these alloys will often fail to meet this requirement. For this
reason, 5183 or 5556 are recommended for these alloys.
Table 3-2: Aluminum Product Selection Guide

ER4043
SuperGlaze 4043
ER4047
SuperGlaze 4047
ER5183
SuperGlaze 5183
ER5356
SuperGlaze 5356
ER5554
SuperGlaze 5554
ER5556
SuperGlaze 5556
6XXX Alloys These Al-Mg-Si alloys are primarily used for extrusion alloys,
although they can often be found as sheet and plate as well. The chemistry of these
alloys makes them very sensitive to hot short cracking. Autogenous welds
(i.e., welds made without adding filler metal) will almost always crack. This is why
6061 filler metal does not exist. If it did, welds made using it would crack. Yet these
alloys are readily weldable using either 4043 or 5356 filler metal. Since the chemistry
of 4043, Al with 5% Si, or 5356, Al with 5% Mg, is so different from that of 6061, when
either is mixed with 6061 the result is a weld with a crack resistant chemistry. In
fact, the vast majority of weld cracking in 6XXX alloys is caused by not adding
enough crack resistant filler to the weld, leaving it crack sensitive. Weldments that
use square butt joint preparations are particularly prone to this problem. The easiest
solution is to make a small V preparation instead of a square butt, which allows the
welder to add more filler alloy.
Whether to use 4043 or 5356 depends on a number of factors. 4043 is easier for the
welder to use, flows better and is more crack resistant. Filler metal 5356 feeds better
and yields welds that are stronger (especially in lap welds and fillet welds) and
more ductile. 5356 should be used to weld the 6XXX alloys to any of the 5XXX alloys.
4043 should be used to weld the 6XXX alloys to the common 3XXX casting alloys.
............................................................................................................................................................
7XXX Alloys Although most of these alloys are not arc-weldable, 7005, 7003 and
7039, display good weldability. These alloys should be welded using 5356.
Figure 3-1: SuperGlaze Aluminum GMAW Wire
Table 3-3: Comparison of Filler Metals 4043 and 5356

ER4043
ER5356
Smooth Bead, Good Wetting
Black Smut, Distinct Ripples
Lower Column Strength
Best Feedability
Higher Penetration
Lower Penetration
Lower Ductility
Higher Ductility
Lower Tensile
Higher Tensile
More Prone to Porosity
Less Prone to Porosity
Anodizes a Dark Grey
Anodizes with Good Color Match
Much Lower Shear Strength
Higher Shear Strength
Lower Cracking Sensitivity
Higher Cracking Sensitivity
Lower Melting Point
Higher Melting Point
Narrower Melting Range
Wider Melting Range
............................................................................................................................................................
Table 3-4: Aluminum Filler Alloy Chart
FILLER
BASE ALLOYS
ALLOYS
Characteristics
1060 1070
1080 1350
W S
2014
2036
1100
M W S
2219
2519
T
M W S
M W S
M W S
M W S
M W S
M W S
A
C
A
B
A
C
A
A
A
A
B
C
A
C
A
B
A
C
A
A
A
A
A
B
B
B
B
A
A
A
C
B
B
A
A
A
A
A
A
B
B
B
C
B
B
C
B
A
A
A
A
A
A
A
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
A
B
A
A
B
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
C
B
B
A
A
B
B
A
B
B
D
A
A
B
C
A
A
C
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
A
A
A
B
B
A
B
B
B
B
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
413.0 443.0
444.0 356.0
A356.0 A357.0
359.0
4043/4047
4043/4047
5087
5183
5356
5554
5556
5556A
5754
A
B
B
B
A
A
A
A
C
B
B
A
A
A
A
A
A
B
B
B
A
A
A
A
C
B
B
A
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
B
B
A B
A B
A
A
6061
6070
A
A
A
B
B
A
B
B
A
A
B
B
B
B
B
A
A
A
B
B
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
B
B
B
A
A
B
B
B
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
B
B
B
A
A
B
B
B
A
A
A
A
B
B
B
A
A
A
B
B
A
A
A
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
B
C
C
B
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
A
A
A
C
A
A
C
A
A
B
C
A
A
C
A
A
A
A
B
B
A
B
B
B
A
B
B
A
5454
5754
5087
5183
5356
5554
5556
5556A
5754
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
511.0, 512.0,
513.0, 514.0,
535.0
5154, 5254
5087
5183
5356
5554
5556
5556A
5754
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
A
A
A
C
A
A
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
5086, 5056
5087
5183
5356
5554
5556
5556A
5754
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
C
A
A
C
A
A
B
C
A
A
C
5087
5183
5356
5554
5556
5556A
5754
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
C
A
A
C
4043/4047
5087
5183
5356
5554
5556
5556A
5754
A
B
B
B
B
A
A
A
C
B
B
A
A
B
B
B
B
A
A
A
C
B
B
A
B
A
A
A
C
B
B
A
B
A
A
A
C
B
B
A
A
A
A
A
B
B
B
B
A
A
A
C
B
B
A
A
A
A
A
B
B
B
A
A
A
A
B
B
B
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
A
A
C
A
A
C
C
A
C
C
C
C
C
B
A
A
A
A
A
A
A
C
B
B
B
B
B
A
A
C
A
C
C
C
C
C
B
A
A
A
A
A
A
A
C
B
B
B
B
B
A
A
C
A
C
C
C
C
C
C
B
A
A
A
A
A
A
C
B
B
B
B
B
A
A
C
C
C
C
C
A
A
5005, 5050
1100
4043/4047
5087
5183
5356
5556
5556A
A
A
A
A
A
B
A
B
B
B
B
B
B
A
A
A
A
A
A
D
C
C
B
C
C
D
A
C
C
C
B
A
A
A
A
A
C
B
B
B
A
A
B
A
A
A
A
A
C
B
B
B
A
C
B
B
B
A
A
C
C
C
A
A
B
B
B
C
A
C
C
C
C
B
B
B
B
D
A
C
C
C
A
A
3004
1100
4043/4047
5087
5183
5356
5554
5556
5556A
5754
C
C
A
A
B
B
B
B
C
C
A
A
B
B
B
B
C
C
B
B
C
C
3003
ALCLAD 3003
1100
4043/4047
B
A
B
B
A
B
A
A
A
A
B
A
B
A
A
B
A
A
A
A
A
B
A
A
2219
2519
2319
4043/4047
2014 2036
2319
4043/4047
1100
1100
4043/4047
B
A
B
A
A
B
A
A
A
A
B
A
B
A
A
B
1060 1070
1080 1350
1100
4043/4047
B
A
B
A
A
B
A
A
A
A
5083, 5456
5052, 5652
A
A
A
A
B
B
B
B
B
A
A
A
A
A
A
B
B
B
B
B
A
A
A
B
B
B
A
C
A
B
A
C
A
A
A
A
C
B
A
C
A
B
A
C
A
A
A
A
A
A
A
1100
4043/4047
1100
4043/4047
A
B
A
C
A
B
A
C
A
A
2319
4043/4047
B
A
A
B
A
2319
4043/4047
A
A
A
A
A
B
B
B
B
B
A
B
B
B
B
B
B
A
A
A
A
A
C
B
B
A
B
B
A
B
B
B
C
B
B
C
B
A
A
B
C
A
A
C
D
C
C
B
A
C
C
A
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
A
1100
4043/4047
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
1100
4043/4047
5087
5183
5356
5554
5556
5556A
5754
A
A
6005, 6005A,
6063, 6082
6101, 6151,
6201,6351,
6951
B
B
B
C
B
B
C
4043/4047
4643 (1)
5087
5183
5356
5554
5556
5556A
5754
5083
5456
B
C
B
B
B
5052
5652
2319
4043/4047
4043/4047
4643 (1)
5087
5183
5356
5554
5556
5556A
5754
5005
5050
3004
M W S
319.0 333.0
354.0 355.0
C355.0 380.0
7005 7021
7039 7046
7146 710.0
711.0
3003
ALCLAD 3003
A
B
B
B
B
B
B
B
A
B
B
B
B
A
A
A
B
A
A
B
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
B
B
B
A
B
B
A
B
B
A
B
B
B
B
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
(Z)
(Z)
B
B
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
C
C
C
A
C
C
A
1100
4043/4047
5087
5183
5356
5556
5556A
A
A
A
A
A
A
B
B
A
B
B
B
B
4043/4047
5087
5183
5356
5554
5556
5556A
5754
............................................................................................................................................................
5052
5652
W S
5083
5456
T
M W S
B
A
A
A
B
A
A
B
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
B
C
C
B
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
B
C
C
B
A
A
A
C
A
A
C
A
A
B
C
A
A
C
A
A
A
A
B
B
A
B
B
B
A
B
B
A
A
A
A
C
A
A
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
C
A
A
C
A
A
B
C
A
A
C
A
A
A
C
A
A
C
A
A
A
A
C
A
A
C
A
A
A
A
A
A
A
A
A
C
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
B
A
A
B
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
B
A
B
B
A
B
B
A
B
B
B
B
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
C
C
C
A
C
C
A
1100
4043/4047
5087
5183
5356
5556
5556A
A
A
A
B
B
A
B
B
B
B
B
B
A
B
B
A
B
B
B
B
M W S
A
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M W S
B
B
A
B
B
A
A
B
B
A
A
A
B
A
A
B
C
A
A
C
5086
5056
A
A
A
A
A
A
B
A
A
B
B
B
A
B
B
B
B
511.0 512.0
513.0 514.0
535.0 5154 5254
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
A
A
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
A
A
A
A
A
(Z)
(Z)
B
B
A
A
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
4043/4047
5087
5183
5356
5554
5556
5556A
5754
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
C
C
C
B
C
C
B
B
B
B
A
B
B
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
A
A
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
A
A
B
B
B
A
A
A
A
A
A
A
A
A
B
B
A
A
A
A
5087
5183
5356
5554
5556
5556A
5754
A
A
A
A
A
A
A
5454
5754
M W S
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
D
A
B
B
A
A
B
B
A
C
A
A
A
A
A
A
A
A
T
A
A
A
B
B
B
C
B
B
C
A
A
B
C
A
A
C
B
B
A
A
B
B
A
C
C
C
A
C
C
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
B
B
A
A
B
B
A
C
C
C
A
C
C
A
B
B
B
A
B
B
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
B
C
A
A
C
B
B
A
A
B
B
A
B
B
B
A
B
B
A
B
B
B
A
B
B
A
B
B
A
B
A
A
B
5087
5183
5356
5554
5556
5556A
5754
B
B
A
B
B
B
B
6005 6005A
6063 6082
6101 6151
6201 6351 6951
A
A
A
A
M W S
A
M W S
M W S
M W S
M W
A
A
A
A
B
A
A
B
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
A
B
A
A
B
D
A
A
B
C
A
A
C
C
B
B
A
A
B
B
A
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
B
A
A
A
A
A
A
A
C
C
A
A
A
B
A
A
B
B
B
A
A
A
A
A
A
A
A
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
C
C
A
A
B
B
A
A
B
B
B
A
A
A
A
A
A
A
A
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
A
A
A
A
A
A
A
A
A
B
B
B
C
B
B
C
C
C
A
A
A
B
A
A
B
B
B
A
A
A
A
A
A
A
A
A
C
C
C
B
C
C
B
A
A
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
A
319.0 333.0
354.0 355.0
C355.0 380.0
413.0 443.0
7005 7021
444.0 356.0
7039 7046
7146 710.0 711.0 A356.0 A357.0 359.0
6061
6070
A
A
B
B
B
B
A
B
B
B
B
A
A
A
A
A
A
A
A
A
2319
4043/4047
4043/4047
4043/4047
5087
5183
5356
5554
5556
5556A
5754
4043/4047
4643 (1)
5087
5183
5356
5554
5556
5556A
5754
4043/4047
4643 (1)
5087
5183
5356
5554
5556
5556A
5754
5087
5183
5356
5554
5556
5556A
5754
5087
5183
5356
5554
5556
5556A
5754
How to Use
1. Select base alloys to be joined.
2. Find the block where the column
and row intersect.
3. This block contains horizontal rows
of letters (A, B, C or D) representative
of the alloy directly across
from them in the filler alloy box at
the end of each row. The letters
in each line give the A-to-D rating
of the characteristics listed at the
top of each column W, S, D, C,
T and M (see Legend at right for
explanation of each letter).
4. Analyze the weld characteristics
afforded by each filler alloy. You
will find that you can trade off
one characteristic for another until
you find the filler that best meets
your needs.
Example
When joining base alloys 3003 and
1100, find the intersecting block.
Note that filler alloy 1100 provides
an (A) rating for ductility (D), corrosion
resistance (C), performance at
elevated temperatures (T), and color
match after anodizing (M), and a (B)
rating for ease of welding (W) and
strength (S). However, if ease of
welding and shear strength are important,
and ductility and color match
can be sacrificed slightly, then filler
alloy 4043 can be used.
SYMBOL
CHARCTERISTIC
Propensity for weld cracking. A

indicates little tendency for weld
W
cracking. D indicates severe
tendency for weld cracking
Shear strength - applicable
S
particularly to fillet welds.
D
Ductility of the finished weld
Resistance to corrosion in ambient
C
temperature fresh or salt water
Recommended for service at
T
Suitability for long term expoure to
temperatures above 150 degrees F
Color match between the weld and
M
the parent material after anodizing
A, B, C, & D are relative ratings in decreasing
order of merit. The ratings have relative
meaning only within a given block.
Aluminum Filler Alloy Chart
.............
Section 4
Welding Preparation
Preparation for welding includes storage and handling of aluminum prior to

welding, methods for making the weld preparation and methods for cleaning prior
to welding. While not strictly welding preparation, methods for backgouging and
interpass cleaning will be included in this section.
4.1 STORAGE OF ALUMINUM AND ALUMINUM WIRE PRIOR TO WELDING

Improper storage of aluminum and aluminum wire prior to welding makes
preparation for welding much more costly at best. At worst, it can result in welds of
inadequate quality.
It is well known that all aluminum alloys form an oxide coating immediately upon
exposure to air. This coating is extremely thin, approximately 100-150 Angstroms
(one millionth of a centimeter) thick. Because it is so thin, it is not visible to the
naked eye. When stored at ambient temperatures and relative humidity levels of
70% or below, the oxide thickness increases extremely slowly. It is safe to say that
aluminum and aluminum wires stored under these conditions will be usable for a
couple of years. Plus, the reverse polarity arc tends to strip off the oxides. Therefore,
if aluminum is stored in a dry area, oxide removal prior to welding will be very easy
or unnecessary.
However, if aluminum is subjected to temperatures above 200F (93C) and/or very
high humidity levels, the thickness of the oxide layer can increase rapidly. Because
of this, the following guidelines are suggested:
Aluminum wire that has ever become wet should be scrapped. Boxes of wire
where the cardboard box has become wet on the inside should be discarded.
Aluminum wire should be stored inside, if possible.
Wire should be stored in the original box and any plastic interior bag it came in.
It is helpful to store wire in a closed cabinet that is heated to approximately 20F
(-6C) above the ambient temperature to reduce relative humidity. This can be
done simply by mounting an electrical fixture with a low wattage bulb inside the
cabinet and letting the bulb burn continuously.
Wire that will not be used for two (2) days or more should be dismounted from
the wire feeder, returned to its original packaging and stored properly.
Aluminum wire that is stored in accordance with the above recommendations will
be usable, with no deterioration in performance, for at least two (2) years. Wire older
than this should be discarded.
Oxides on an aluminum plate can be removed by power wire brushing, sanding,
grinding or chemical etching; however, please note that proper storage will prevent
the formation of oxides. Aluminum should be stored indoors in a dry environment.
Welding Preparation
............................................................................................................................................................
If stored outside, it should be securely covered to keep it dry. Under no

circumstances should it be stored uncovered with one plate lying flat on top of
another. This will allow water to wick in between the plates from the edges. If
this happens, thick hydrated oxide will form very quickly on the plate surfaces,
making it difficult to pry the two plates apart.
4.2 WELDING PREPARATION
Even the hardest aluminum alloy is much softer than a high speed steel or carbide
cutting tool. While specialized tools are available to cut aluminum, aluminum is
easily cut using circular saws, radial arm saws, and the like. End preparations can
be put on pipe or tube using woodworking routers. The general rule is if it will cut
wood, it will cut aluminum.
Mechanical methods of weld preparation are as follows:

Machining
Machining of weld preparations can be performed using a variety of tools. Milling
machines, bed planers and shapers are commonly used with carbide cutting tools.
It is recommended that any machining be performed dry, i.e., without any cutting
lubricants. Lubricants are either oil (hydrocarbon) or water-based. If lubricants are
used, the residue must be removed before welding. If not removed, excessive
porosity will result.
Sawing
Both band and circular saws are commonly used to make weld preparations.
Higher blade speeds and coarser teeth are required than when cutting steel.
Recommended blade surface speeds are 8000 surface feet per minute (sfpm) for
circular saws and 5000 sfpm for band saws. Band saw blades should have no more
than 4 teeth per inch. If circular saws are used, the cut quality can be good enough
so that no further preparation is necessary. Band saws usually leave a coarse
surface that must be sanded or grinded.
Grinding and Sanding
The use of grinding and/or sanding to form weld preparations was discouraged in
the past because organic binders in the disc often left behind organic residues that
caused weld porosity. Today, there are a number of grinding and sanding discs
specifically formulated for aluminum. These can give excellent results for forming
weld preparations on aluminum.
Welding Preparation
............................................................................................................................................................
Shearing
Shearing is very useful to cut sheets or plates to size, but the edge quality is rarely
acceptable for welding. It is relatively rough and has many crevices that can trap
oils, greases and the like. It is recommended that you smooth the edge by
machining, grinding or sanding after shearing.
Routers & Carbide Burrs
You can use routers for repairs and back-gouging. If using an air powered router,
ensure that there is a dryer on the line to prevent moisture from getting on the
work-piece. When using for repair work or back gouging, make sure that the
material is removed to sound metal.
Water-Jet Cutting
Water jet cutting utilizes high pressure water with the addition of an abrasive
garnet. Water pressures can reach 100 kilopounds per square inch (ksi), and the
velocity of the water can reach speeds above Mach 3 or 2283 mph. Temperatures
only reach 195F, which allows the aluminum to be cut without causing liquation
cracking. This process can cut aluminum up to up to 9.25 in. thick in certain
applications. There are, however, limitations to the process. Cutting speeds are
relatively slow, especially when compared to plasma arc cutting. For example,
water-jet cutting speeds may be as slow as 3.8 inches per minute (ipm) on 1.5 in.
thick material using 90 ksi water pressure for a good-quality cut. In addition,
waterjet cutting systems are generally expensive and not portable.
Thermal Cutting Technologies
While aluminum cant be cut using oxyfuel cutting equipment, it can easily be cut
using plasma and laser cutting equipment. Heat-treatable alloys are prone to form
micro cracks due to liquation cracking, which can extend back from the cut edge as
far as 1/8 in. (3.2 mm). Therefore, laser or plasma cut edges in heat-treatable alloys
should be machined to remove the edge before welding.
Plasma Cutting
You can produce an acceptable quality cut on aluminum 1.5 in. thick using a 400A
power source with a travel speed of 35 inches per minute (ipm).
Laser Cutting
Because of the high reflectivity and high conductivity of aluminum, laser cutting
isnt as effective as other methods of preparation; therefore, solid state laser
cutting gives the best result when cutting aluminum. This process is typically
limited to materials 3/8 in. (9.5 mm) thick.
Welding Preparation
............................................................................................................................................................
4.3 PRE-WELD CLEANING

Once the weld preparation is formed, it must be cleaned before the weld joint is fit
together. Cleaning consists of removing any contaminants. These contaminants
are as follows:
Whichever method you use, you must degrease the part to be welded before
performing any of the oxide removal procedures outlined below. Otherwise, the oils
and greases will be spread by the oxide removal and will be difficult to remove.
(1) Oils and Greases

Removal of oils and greases can be performed in one of several ways. First, you can
wipe with a clean rag saturated with a degreasing solvent. This method is effective;
however, the use of many solvents has been severely curtailed in recent times due
to environmental concerns. Second, mild alkaline solutions make good degreasers.
The part to be degreased can be sprayed with these solutions or dipped into a tank
containing them. Since such cleaners are usually water based, it is important to
thoroughly dry the part after degreasing. Third, you may use an acid based
cleaning solution for cleaning aluminum. These are usually effective. However, all
are acidic and some contain hydrofluoric acid, so you must be cautious when
using and discarding them. Again, since these solutions contain water, you must
dry the piece thoroughly before welding.
(2) Excess Oxides
Once you have removed the oils and greases, you may remove the oxides in several
ways. The most common way is to use a stainless steel wire brush. The brush
should be clean and not previously used on materials other than aluminum. The
brush should be relatively flexible and used with light pressure in order to avoid
unnecessarily roughening the surface of the aluminum.
You can also remove oxides by immersing the part in a strong alkaline solution.
However, these solutions are very corrosive and can etch the surface of the
aluminum; therefore, be sure to use extreme caution.
In some industries, especially the aerospace industry, final oxide removal is
performed just before the joint is fitted together. This is accomplished by
mechanically removing the oxide using a steel scraper (identical to those used in
woodworking) or by draw filing. Once the cleaning is performed, the joint is fit
together as soon as possible. This is an effective method of oxide removal.
However, it is time consuming, costly and primarily used in industries where the
demand for extremely high quality overrides the additional cost.
Welding Preparation
............................................................................................................................................................
4.4 INTERPASS CLEANING

The surface of a weld usually has areas of oxides and weld smut. This gray to
black colored smut is composed of aluminum oxide and magnesium oxide. We
recommend that you remove the smut and oxides before depositing another weld
pass; otherwise, they can cause lack of fusion defect.
The easiest way to remove these oxides is to use a wire brush, either manual or
power driven. The wire brush should be clean and used only on aluminum. It should
be flexible and used with light pressure.
4.5 BACKGOUGING
When making a double-sided weld, it is necessary to remove the metal on the back
side to sound metal before depositing the back side weld. If you neglect to do this and
make the backside weld with no preparation, lack of fusion will often result. The usual
geometry for the backgouged seam is a V preparation with a 60 included angle and a 1/8
in. (3.2 mm) radius at the base. There are a number of ways to perform this backgouging:
(1) Air Arc or Plasma Arc Gouging
Either of these processes can be used successfully. However, they rely on the skill
and steadiness of the operator to obtain a uniform backgouge. In addition, they
usually require cleaning up with a grinding disk before welding. This is especially
true of air arc gouging, which leaves carbon deposits in the gouged groove. If the
carbon isnt removed, porosity on the backside weld can result.
(2) Grinding
A thin 1/8 in. (3.2 mm) grinding disk on edge can be used for backgouging. Again, it
takes a great deal of skill to produce a uniform gouge.
(3) Machining
The best way to get a uniform backgouge is to mount the weld in a milling machine
and machine the backgouge. Unfortunately, this usually isnt practical. However, a
number of manufacturers supply a pneumatically powered circular saw mounting a
4 in. (102 mm) diameter milling cutter. This milling cutter is ground to have a tooth
form with a 60 V with a 1/8 in. (3.2 mm) tip radius. The depth of the backgouge is
determined by setting the cutting depth of the saw. It is relatively easy to set up a
straightedge to guide the saw so that you get a straight backgouge.
(4) Chipping
Although not used very often, a pneumatic chipping hammer with the appropriate
chisel can be an effective way to backgouge. The problem with this method is the
extremely high noise level produced. An advantage of this method is that its easy to
regulate the cutting depth: when you reach sound metal, youve reached the correct
cutting depth.
.............
Section 5
GMAW of Aluminum Alloys
5.1 PROPERTIES OF ALUMINUM

The engineering use of wrought and cast aluminum base materials continues to
increase because of the basic properties of this unique material. The more
prominent features of aluminum and its alloys are as follows:
Aluminum is lightweight. Its weight is about one third that of steel. A cubic inch
of aluminum weighs 0.098 lbs/in compared to steel, which weighs 0.283 lbs/in.
Aluminum has a wide range of strength properties that vary from 13,000 psi
tensile strength for pure aluminum up to 90,000 psi tensile strength for the
strongest heat-treatable aluminum alloys.
Aluminum provides excellent corrosion resistance in many environments.
The thin refractory oxide that forms on the surface of aluminum provides a
protective barrier.
Aluminum is an excellent conductor of heat. It is up to five times more thermally
conductive than steel.
Aluminum is reflective of radiant heat, and the surface finish of aluminum is
frequently used to take advantage of this feature.
Aluminum is widely available in either extruded shapes or wrought sheet in an
equally wide range of alloy compositions.
Aluminum is widely available as a die cast base material.
For welding purposes, an important consideration for welding aluminum is its
thermal conductivity. This property has an important facet: To compensate for
the high rate of thermal conductivity, aluminum requires the use of higher energy
modes of metal transfer. Axial spray and pulsed spray are the two recommended
GMAW modes of metal transfer for aluminum. The use of the lower energy forms
of metal transfer, such as short circuiting transfer, will usually result in incomplete
fusion defects.
5.2 MODES OF METAL TRANSFER

When welding aluminum base material, it is important to note that the thermal
conductivity of the aluminum base material is five times higher than it is for carbon
steel, and because of this the lower energy modes of metal transfer are unable
to provide sufficient melting of the base material to ensure good fusion. More
specifically, short circuiting transfer is not recommended for welding aluminum.
Axial spray and pulsed spray metal transfers are the preferred metal transfer
modes for aluminum. Each of these is capable of providing the required energy
levels for base metal melting to ensure good fusion.
............................................................................................................................................................
Table 5-1 shows the typical axial spray transfer transition currents for specific
aluminum electrode diameters (note that argon gas is the shielding gas associated
with the transition currents). In those cases where helium additions are made to
the argon, the required watt energy level (current x voltage) to achieve the
transition to axial spray will have to increase. Axial spray is the highest energy
transfer mode for GMAW, and aluminum requires the use of higher energy modes
of transfer to compensate for the higher thermal conductivity. Because of these two
central facts, axial spray is generally applied to aluminum base materials 0.125 in.
(3.2 mm) or greater in thickness.
Table 5-1: Axial Spray Transition Current

Aluminum Electrode Diameter
Shielding Gas
Transition Current
Inches
mm
0.030
0.8
100% Argon
70 Amps
0.035
0.9
100% Argon
90 Amps
0.047
1.2
100% Argon
130 Amps
0.062
1.6
100% Argon
180 Amps
For many years, we were limited to these transition currents shown in Table 5-1 as
a minimum for GMAW of aluminum. This meant that GMAW could be used for
welding relatively thick aluminum sections but couldnt be used for welding thin
aluminum because the current was too high.
Pulsed Spray Welding (GMAW-P)
The invention of pulsed spray power supplies was the key to welding thin
aluminum. In GMAW-P, the welding current is pulsed between a peak current that
is higher than the transition current and a much lower background current (see
Figure 5-1). This means that we can use GMAW-P to weld at average currents far
below the transition current for the wire being used. In axial spray mode, by
contrast, filler wire is transferred across the arc at the peak current, and no wire is
transferred at the background current. GMAW-P is the preferred mode of metal
transfer for materials 0.125 in. (3.2 mm) and thinner because the average current is
lower in magnitude for GMAW-P than for axial spray transfer. GMAW-P is able to
join thin and thick sections of aluminum. GMAW-P has the following advantages
when used for welding aluminum when compared to axial spray transfer:
Lower heat input less distortion
Ability to handle poor fit-up
Ability to handle thinner materials
............................................................................................................................................................
Lower heat input of GMAW-P reduces the size of the heat affected zone
Out-of-position welding is greatly enhanced
Please consult Table 6-3 on page 61 for recommended GMAW-P parameters.
Figure 5-1: Pulsed GMAW Waveform
Constant Voltage (CV) GMAW

CV power supplies were developed many years ago specifically to be used for
Gas Metal Arc Welding and have been the most commonly used power supplies,
although many users have changed over to the newer technology Pulsed GMAW
power supplies, especially for welding aluminum. In the CV power supply, the user
presets the Arc Voltage and the Wire Feed Speed (WFS). The power supply then
keeps the arc voltage constant during welding. It does this by varying the welding
current to keep the arc voltage (and thus the arc length) steady. Such power supplies
can be used at low currents and low voltages in short circuiting transfer or at higher
currents and higher voltages for spray transfer. However, short circuiting transfer is
never recommended for welding aluminum.
Typical welding parameters for CV welding are shown in Table 6-3. Note that
parameters shown are only for spray transfer, so the material thicknesses are
relatively large.
............................................................................................................................................................
No parameters are shown for thinner materials, as this would require the use of
welding currents below the transition current, which would make them into short
circuiting transfer. Pulsed spray, AC GMAW or Pulse On Pulse processes are more
suitable for thin materials
Power Mode
Power Mode, a Lincoln Electric patented process, is a combination of constant
current (CC) and constant voltage (CV) modes. In Power Mode, neither the current
nor the voltage is held steady. Instead, the weld power is held constant. Figure 5-2
shows a comparison of the voltage-amperage curves for CV, CC, and Power Mode.
In Power Mode, the wire feed speed and the power levels (in KW) are preset. The
power is adjusted to obtain the appropriate arc length for the preset WFS.
Like CV, Power Mode can be used over the entire range of wire feed speeds to
provide short circuiting transfer and axial spray transfer. However, the high
thermal conductivity of aluminum still makes short circuiting transfer inadvisable,
so Power Mode should usually be used on thicker materials at higher wire feed
speeds. When used in this manner, Power Mode can show considerable advantage
over conventional CV modes. Specifically, Power Mode gives more consistent
penetration and a more stable arc than CV. Please consult Table 6-3 to find
recommended CV parameters for various thicknesses.
Figure 5-2: Output Characteristics of CC, CV and Power Mode
............................................................................................................................................................
Pulse On Pulse Mode

Pulse On Pulse mode, a patented Lincoln invention, is similar to pulsed spray
welding. In conventional pulsed spray welding, one pulse wave form is repeated ad
infinitum. In contrast, in Pulse On Pulse a number of high energy pulses is
followed by the same number of low energy pulses (see Figure 5-3). These pulsed
waves create a weld ripple when we are in the low energy part of the waveform.
Pulse On Pulse is therefore a way to obtain a very uniform weld bead with the
characteristic stacked dimes appearance of a TIG weld. The weld ripple spacing
can be varied by changing the Ultimarc setting.
Suggested Pulse On Pulse welding parameters for various material thicknesses are
shown in Table 6-3.
Figure 5-3: Pulse On Pulse Waveform
............................................................................................................................................................
AC Pulse
Lincoln Electric has recently introduced a process that uses alternating current (AC)
for GMAW. This is done by adding an Advanced Module, see Figure 5-4a and b, to any
of the latest generation Lincoln Electric power supplies. The advantage of this process
is that in GMAW, direct current electrode positive (DCEP) increases heat input and
penetration while direct current electrode negative (DCEN) reduces heat input and
increases weld deposition rate. Lincoln Electric has developed AC GMAW waveforms
for aluminum by adding an EN pulse at the end of each EP pulse, see Figure 5-5.
Figure 5-4a: Power Source with Advanced Module

Waveform
Peak
Propels droplet toward

the weld pool.
Figure 5-4b: Power Source with Advanced Module
AC Aluminum Pulse
1
2
Negative Background
Reduces heat input by
redirecting current flow
towards the electrode.
Figure 5-5: AC GMAW Waveform
Positive Background
Completes droplet transfer

and begins the creation of the
next droplet.
............................................................................................................................................................
AC GMAW can be used in two ways. First, to keep the wire feed speed constant,
reducing heat input and allowing you to weld very thin materials. Second, to keep
heat input the same, meaning the deposition rate (and therefore travel speed) can be
increased to weld slightly thicker materials, 0.08 in. (2 mm) and thicker.
Welding parameters for AC GMAW are shown in Table 5-4.
Table 5-4: AC GMAW Welding Parameters
100Ar
1/2 in.
SuperGlaze
4043
0.035 in (1.1 mm)
SuperGlaze
4043
3/64 in (1.2 mm)
in (mm)
0.10 (2.5)
0.08 (2.0)
0.06 (1.5)
0.04 (1.0)
WFS (IPM)
465
390
300
155
110
100
83
56
20.4-22.4
19.5-21.5
19.0-21.0
17.5-19.5
0.0
0.0
0.0
-5.0
0.12 (3.0)
0.08 (2.0)
0.06 (1.5)
0.04 (1.0)
300
210
175
110
140
105
95
70
20.5-22.5
19.2-21.2
18.7-20.7
17.9-19.9
0.0
0.0
0.0
-5.0
SuperGlaze
4043
1/16 in (1.6 mm)
0.12 (3.0)
150
149
20.5-22.5
0.0
0.08 (2.0)
115
129
20.0-22.0
-5.0
SuperGlaze
5356
0.035 in (1.1 mm)
0.10 (2.5)
0.08 (2.0)
0.06 (1.5)
0.04 (1.0)
525
460
365
200
118
107
91
58
18.4-20.4
18.1-20.1
17.2-19.2
16.3-18.3
5.0
2.5
0.0
-5.0
SuperGlaze
5356
3/64 in (1.2 mm)
0.12 (3.0)
0.08 (2.0)
0.06 (1.5)
0.04 (1.0)
400
275
210
120
154
118
95
64
18.5-20.5
17.9-19.9
16.7-18.7
15.3-17.3
5.0
0.0
0.0
-5.0
SuperGlaze
5356
1/16 in (1.6 mm)
0.12 (3.0)
0.08 (2.0)
0.06 (1.5)
245
125
100
171
107
88
19.6-21.6
16.9-18.9
16.7-18.7
0.0
0.0
-10.0
............................................................................................................................................................
5.3 POWER SUPPLIES AND WIRE DRIVES

The history of the development of power sources for aluminum GMAW welding
relates to the development of CC or CV output characteristics. Prior to the
development of CV power sources, CC or drooper type power sources were used
exclusively for welding aluminum. Special techniques were required for arc
striking, and special variable-speed wire drives were developed as a solution for the
unstable arc length associated with constant current.
Incomplete fusion defects often accompanied the penetration problems. Because

of this, many aluminum fabricators went back to CC power supplies for consistent
penetration. As a result of these early difficulties, much of the available aluminum
welding literature continues to advocate the use of CC supplies. Constant voltage
power supplies produced since the 1990s demonstrate more consistent output.
These newer CV power sources are line voltage compensated, which ensures
consistent delivery of output. CV is widely used and highly recommended for
aluminum GMAW.
5.4 GMAW-P POWER SUPPLIES
Todays pulsed arc power supplies are much more sophisticated than those of only
a few years ago. Early pulsed power supplies had a fixed pulsing frequency based
upon multiples of input frequencies, usually 60 and 120Hz. These systems were
non-synergic and difficult to set up.
The 1990s introduced newer pulsed power sources that provided synergic control
(one knob control) with a high speed amplifier used to control output. In the
newer pulsed arc power sources, either an inverter transformer or related Chopper
Technology provide power for the arc, and software is used to direct the output of
the power source.
The software developed specifically for these newer power sources provides
a wide selection for a range of filler types, diameters and shielding gas
compositions. In most cases, the newer power sources provide a wide selection
of pulsed spray transfer, synergic CV and special Pulse on Pulse programs for use
with aluminum electrodes.
In the following section, we will explain what each adjustment knob on the power
supply does. Keep in mind that this is a general discussion, and your power supply
may differ slightly from what is discussed below.
............................................................................................................................................................
5.5 WELD MODE SEARCHING

The Weld Mode Search feature allows the selection of a welding mode based on
certain criteria (wire size, process type, etc.).
Searching for a Weld Mode
1. To search for a mode, turn the control knob
until Weld Mode Search is displayed. This
will appear in between the highest and the
lowest weld mode numbers.
2. Once Weld Mode Search is displayed,
pressing the right pushbutton labeled
Begin will start the search process.
3. During the search process, pressing the
right pushbutton typically acts as a next
button and the left pushbutton typically
acts as a back button.
4. Rotate the control knob, then press the
right pushbutton to select relevant welding
details such as welding process, wire type,
wire size, etc.
5. When the final selection is made, the
power source will automatically change to
the weld mode found by the Weld Mode
Search process. Earlier products may not
have this feature. To activate this feature, a
software update may be needed.
Figure 5-6: Power Wave C300
Adjusting Voltage/Trim
The right display and knob control voltage, trim or output depending upon the
process selected. Once welding is complete, the display continues to show the
welding voltage for five seconds. See Table 5-5 for more details.
............................................................................................................................................................
Table 5-5: Adjusting Voltage/Trim

Process
Display/
Function
Description
Non-synergic
GMAW (MIG)
Voltage
Adjusts the voltage. The display is blank for

nonsynergic STT modes.
Voltage
When the voltage knob is rotated, the display

will show an upper or lower bar indicating
if the voltage is above or below the ideal
voltage. The display is blank for synergic
STT modes.
Preset voltage above ideal voltage
(Upper bar displayed)
Preset voltage at ideal voltage
(No bar displayed)
Preset voltage below ideal voltage
(Lower bar displayed)
Trim
Pulse welding controls the arc length with

Trim instead of voltage. When trim
(arc length) is adjusted, the Power
Waveautomatically recalculates the voltage,
current and time of each part of the pulse
waveform for the best result. Trim adjusts
the arc length and ranges from 0.50 to 1.50.
Increasing the trim value increases the arc
length, while decreasing the trim value
decreases the arc length.
Synergic
GMAW (MIG)
Pulse
GMAW (MIG)
Trim .50
Arc Length Short
Trim 1.00
Arc Length Medium
Wave Control
Wave Control is used to adjust the arc for exact preferences. The wave control functions
vary for different processes and weld modes. See Table 5-6 for more details.
Trim 1.50
Arc Length Long
............................................................................................................................................................
Table 5-6: Wave Control

Wave Control
Name
Effect/Range
Description
GMAW (MIG)
Pinch
Soft (-10.0) to
Crisp (10.0).
Pinch controls the arc characteristics when short-arc welding.

Note: This has no effect when welding aluminum.
GMAW-P
(Pulsed MIG)
UltimArc
Process
Soft (-10.0) to
Stiff (10.0)
Arc Control - 10.0

Low Frequency, Wide
Arc Control OFF

Medium Frequency
and Width
Arc Control +10.0

High Frequency,
Focused
For Pulse modes, Arc Control changes the pulsing frequency.

When the frequency changes, the Power Wave system
automatically adjusts the background current to maintain a
similar heat input into the weld. Low frequencies give more
control over the puddle and high frequencies minimize spatter.
For Pulse On Pulse modes, Arc controls changes the frequency

modulation. The frequency modulation controls the spacing of the ripples
in the weld. Use low values for slow travel speeds and wide welds, and high
values for fast travel speeds and narrower welds.
GMAW-P
(Pulsed MIG),
Aluminum
Ultimarc
Low (-10.0) to
High (10.0)
Modulation frequency =10

Wide weld and ripple spacing,
slow travel speed
Modulation frequency =10

Narrow weld and ripple spacing,
fast travel speed
............................................................................................................................................................
Table 5-6: Wave Control Contd.

Process
Wave Control
Name
Effect/Range
Description
Fine tunes the heat input into the plate. Increasing the setting
provides more heat into the puddle, resulting in a more
focused arc. Decreasing the setting reduces heat directed into
the puddle, resulting in a less focused arc.
Standard Pulse
0
AC GMAW
UltimArc
Low (-10.0) to
High (10.0)
AC Pulse
UltimArc
+10
0
-10
-10
+10
............................................................................................................................................................
Table 5-7: Start Options

Process
GMAW (MIG)
Start Options
Effect/Range
Description
Preflow* time
0 25.0 seconds
Starts the shielding gas for a preset amount of time before the arc is started.
Run in WFS
Auto, OFF, 30
in/min to weld
WFS
Run-In sets the wire feed speed from the time the trigger is pulled until an
arc is established or 2.5 seconds. Use run-in for softer arc starts.
Start time**,
WFS, and Volts
0 10.0 seconds
The Start Procedure controls the WFS and Volts for a specified time at the
beginning of the weld. During the start time, the machine will ramp up or
down from the Start Procedure to the preset Welding Procedure.
* Preflow reduces the amount of porosity at the beginning of the weld.

** Start Time - To reduce the look of a cold start use parameters lower than that of the weld, to reduce lack of fusion use parameters
higher than that of the weld.
Newer power sources automatically set these values synergically based on wire feed speed.
Table 5-8: End Options

Process
GMAW (MIG)
Start Options
Effect/Range
Description
Spot timer
5.0 seconds
Sets the length for welding when the trigger is pulled. If the trigger is released
before the Spot Timer is complete, welding stops. This option has no effect in
4-step trigger mode.
Crater*
time, WFS
and Volts
0.0 10.0
seconds,
Auto
Crater procedure controls the WFS and volts for a specified time at the end of
the weld after the trigger is released. During the crater time, the machine will
ramp up or down from the weld procedure to the crater procedure. Crater is not
commonly used with the STT process.
Burnback
Time
The burnback time is the amount of time that the weld output continues after
0.0 0.25 seconds the wire stops feeding. It prevents the wire from sticking in the puddle and
prepares the end of the wire for the next arc start.
Postflow
Time
0.0 0.25 seconds Adjusts the time that shielding gas flows after the welding output turns off.
* Crater: Use to reduce/eliminate the likelihood of crater cracking. Depending on the weld size the parameters will differ.
Newer power sources automatically set these values synergically based on wire feed speed.
............................................................................................................................................................
5.6 WIRE DRIVES AND CONTROLS

Reliable feeding of the softer aluminum solid wire electrodes through a welding
torch presents more of a challenge than feeding carbon steel electrodes. Aluminum
wire is much less rigid than steel wire, so it is harder to push through a GMAW
torch. Special wire drives and GMAW guns are available to enhance the feedability
of aluminum electrode. They fall into four main categories:
1. Push Type Feeders
Standard wire feeders, employed for carbon steel solid wire electrodes, can also be
referred to as push type feeders. In this type of equipment, a spool of wire is
mounted on a spindle located to the rear of the drive. A shielding gas pre-flow and
post-flow timer/control should be available. There is a set of drive rolls (two-roll or
four-roll) on the feeder that pushes the wire through from the spool mounting
device through the gun cable and then through the contact tip.
For aluminum electrode, the use of highly polished U groove drive rolls is
recommended. In all of the ensuing scenarios, the use of hard shell nylon or
Teflon type liners is strongly recommended. This type of system, with some
modifications described below, can also be used to feed softer aluminum wire
under the following circumstances:
The gun cable must be kept short; 10-12 ft. (3.0-3.6 m) is the practical maximum
length. The shorter the GMAW gun cable, the better the overall performance. Use
Teflon or hard shelled nylon electrode liners.
If 1/16 in. (1.6 mm) diameter wire is used, either 4043 or 5356 filler alloys can be
pushed. The thicker electrodes have higher column strength. Again, use Teflon
or hard shell nylon electrode liners.
3/64 in. (1.2 mm) 5356 filler metal can generally be pushed, but 3/64 in. (1.2 mm)
4043 filler metal will usually result in wire feeding problems if pushed.
Plastic- or aluminum-specific inlet and outlet guides and special aluminum
contact tips are also recommended.
U-grooved type drive rolls should be used.
............................................................................................................................................................
2. PushPull Type Feeders

A solution to the problem of feeding
either small diameter or softer
aluminum wire is to use a pushpull
feeder. In most push-pull feeders, the
pull motor in the welding gun is the
master motor and the push motor in
the cabinet is the slave motor.
Wire feed speed is controlled by the
motor on the gun handle, and the
cabinet contains a motor system
designed to provide a slack wire
reducing effect on the electrode. This
push-pull type of aluminum wire drive
system provides the most consistent
daily performance when compared to
the other types of systems. Figure 5-9
shows a complete push-pull system.
Figure 5-9: Complete Push-Pull Drive System
The push-pull systems handle aluminum diameters from 0.030 to 1/16 in. (0.8 - 1.6
mm). They reliably feed aluminum wire up to 50 ft. (15.2 m) from the control cabinet.
3. PushPull GMAW Guns
Figure 5-10 shows a push-pull gun. The bulged area of the gun handle houses the
pull drive motor. This permits the use of a more integrated approach for feeding
aluminum. There are several control methodologies to coordinate the push motor
with the pull motor. Lincoln Electric synchronizes the speed of the two motors so
that the speed of the pull motor is slightly higher than that of the push motor. This
keeps the wire under tension in the gun cable.
Figure 5-10: Magnum Push-Pull Gun
............................................................................................................................................................
4. Spool Guns
Another solution for light duty
aluminum welding is the spool gun
shown in Figure 5-11. In this system,
a 1 lb. (0.5 kg) spool of filler wire is
mounted directly on the rear of the
GMAW gun, so that it is only pushed
a few inches past the drive rolls,
show in inset. These spool guns are
Figure 5-11: Spool Gun
usually air-cooled and rated for 200 A
maximum at 60% duty cycle, so they
are not recommended for high current or high duty cycle welding.
5.7 ALUMINUM FEEDING ENHANCEMENTS

Drive rolls should always be the polished U groove type for aluminum.
The U groove is designed to cradle the softer electrode without altering its
shape and the high polish prevents the accumulation of aluminum oxide in
the drive roll groove. Steel electrodes use either knurled rolls or a V groove
configuration. Drive rolls designed for carbon steel electrodes should not be
used for feeding aluminum.
Inlet and outlet wire guides for
feeding aluminum should
be made from Teflon, nylon
or other suitable plastic
material. A typical wire guide
for aluminum is shown in
Figure 5-12. Wire guides for
steel wire are usually made
from steel and should not be
used to feed aluminum.
Gun liners for aluminum
welding should be either
Teflon, nylon or other plastic
Figure 5-12: Drive Rolls and Wire Guide for Aluminum
liner material. Some of these
types of aluminum liners will
have a short coiled brass liner
section located at the front of the plastic liner. Liners for guns made to feed steel
are usually made from spirally wound small diameter steel wire. These types of
liners should not be used for feeding aluminum. They will shave the aluminum
wire and then quickly clog the path.
............................................................................................................................................................
Most manufacturers make contact tips specifically for aluminum wire.

Aluminum readily expands as it absorbs the heat of the arc. Aluminum contact
tips for a given size aluminum wire are designed to accommodate the thermal
expansion of the wire the inside diameter of the contact tip is slightly larger
than those for the same size steel wire. Contact tips for welding steel are not
suitable for welding aluminum.
Some drive roll kits for aluminum include springs specifically designed to deliver
the appropriate tension on the drive rolls. When these are included with a kit,
they must be used as they are a different tension than the springs.
Some welders, after encountering aluminum feeding problems, opt to use oversize
contact tips, i.e., 1/16 in. (1.6 mm) tips on 3/64 in. (1.2 mm) wire. This is usually
unacceptable. The contact tip must transfer current to the wire. An oversized tip
will not allow consistent current transfer. Arcing in the tip will occur, which will
produce sharp burrs on the bore of the tip.
Another unacceptable practice is to use a wire straightener and tighten it down
hard so that all of the cast is removed from the wire. Because the wire needs cast to
make proper contact in the tip, removing all of the cast usually results in burnback.
The contact tip should be flush with the end of the gas nozzle or recessed
approximately 1/8 in. (3.2 mm). The tip should not extend past the gas nozzle.
5.8 SHIELDING GAS

The only shielding gases for welding aluminum are argon and mixtures of argon
and helium. Shielding gas components such as oxygen, hydrogen or CO2 should
never be used for aluminum GMAW. Even in trace amounts, these gases will
adversely affect the weld. However, it has been determined that additional amounts
of nitric oxide of less than 1% minimize the formation of ozone. Gas mixtures of
argon or argon/helium with a nitric oxide addition are often sold for welding
aluminum and work well.
The recommended shielding gas for welding aluminum up to approximately 1/2 in.
(12.7 mm) in thickness is 100% argon. Above this thickness, where additional energy
is needed to melt the material, it is common to use gas mixtures of 75% argon/25%
helium or 75% helium/25% argon. The use of helium in the arc increases
the arc voltage and weld penetration and provides additional energy to enable
heavier section thickness welding. It also expands the cross sectional shape of the
finished weld, giving it a more rounded appearance. Shielding gas flow rates range
from 30 to 100 cubic feet/hour (cfh) (14 to 47 L/min). Higher flow rates are employed
for wider diameter gas nozzles and when using higher helium two-part blends.
............................................................................................................................................................
5.9 WELDING TECHNIQUES

Black soot on the surface or the adjacent areas of a weld is referred to as smut.
Smut is made up of finely divided oxides of aluminum and magnesium. The weld
itself should be bright and shiny, with no smut on it. Smut at the edges of the weld
is expected and normal, especially when using a 5XXX filler metal. This occurs
because 5XXX fillers contain appreciable magnesium, which is very effective at
forming smut. Otherwise, the presence of smut usually indicates that adjustments
in technique are necessary.
The most common mistake beginners make when learning aluminum GMAW, is
holding too long a contact tip to work distance (CTWD). Shorter CTWDs, 1/2 in. to
5/8 in. (12.7 - 15.8 mm), are required when welding aluminum. If the CTWD is too
long, the gas shielding will be insufficient and the weld will most likely be covered
in black smut.
It is not uncommon to get a cold-looking weld bead for the first 1/2 in.
(approximately 12.7 mm) of the weld. This is due to the high thermal conductivity
of aluminum. You can minimize this condition by using a power supply with a hot
start. A common alternative used in the absence of a hot start control is to strike
the arc about 1 in. (25.4 mm) ahead of the nominal weld starting point and quickly
maneuver the arc back to the desired starting point. This action has the effect of
providing preheat to the aluminum base material, and it provides improved fusion
at the beginning of the weld. Another alternative is to strike the arc on a run-on tab
that is removed later.
While welding, hold the torch with a push angle of 5 to 10 (also known as a leading
torch angle). If you hold the torch using a drag angle (also known as a lagging torch
angle), then the gas shielding will be absent from the molten puddle and the finished
weld will appear gray or black.
Be careful when you extinguish the arc. Terminating the arc abruptly will result in
a deep weld crater that may contain a shrinkage crack.
............................................................................................................................................................
There are a number of ways to minimize the size and depth of the crater:
Use weld tabs; start and terminate the weld on them.
A power supply with an arc decay control allows the electrode and current to tail
off for a predetermined wire feed speed per unit of time. This permits a controlled
fill of the aluminum weld crater.
Near the end of the weld, progressively increase the travel speed. The effect here
is to reduce the size of the weld bead and diminish the overall size of the crater.
This is known as a feathering or back step technique.
At the end of the weld, reverse the direction of the torch to place the crater within
the body of the weld bead.
Figure 5-13: Straight Progression Weld
Figure 5-14: Back Step Welding Technique
............................................................................................................................................................
Some welders learn GMAW by keeping a very steady, constant motion in the travel
direction to make a very smooth weld with a minimum of weld ripples. This is
known as a straight progression type weld bead (see Figure 5-12). Other welders
learn to weld by using the back step technique (see Figure 5-13). Each of these
techniques produces a weld with distinct, evenly spaced ripples. Each technique
produces acceptable finished welds.
The finished weld should be bright and free from oxides and smut. A frost line or
cleaning stripe approximately 1/16 in. to 1/8 in. (1.6 to 3.2 mm) wide should be
visible along each edge of the weld. These stripes show the area where the reverse
polarity arc has removed the oxide from the aluminum surface. If the weld metal is
black or gray, or if the cleaning stripes are not present, something is wrong. The
most likely causes are either the arc length is too long or the torch angle is wrong.
You may expect to find some weld smut at the edges of the weld. There will also be
some weld smut present at weld starts, stops and at internal and external corners.
More smut will be present when using 5XXX filler than when using 4XXX filler.
.............
Section 6
Weld Defects Causes and Cures
Some weld defects or discontinuities may be small enough that they dont seriously
impair the mechanical properties of the weld joint. On the other hand, some
discontinuities may cause immediate joint failure. The effects of other
discontinuities may be more insidious.
In this section, we will not attempt to assess the acceptability or rejectability of
specific discontinuities. Instead, we will discuss the appearance of the various
types of weld defects and suggest methods to minimize or eliminate these defects.
Cracking
Cracking occurs when a combination of a susceptible microstructure or chemistry
and a sufficiently high solidification stress are present. If you reduce the stress or
change the microstructure or chemistry, the cracking can be eliminated.
All weld cracking in aluminum is caused by hot cracking. That is, it takes place
during weld solidification.
Crater Cracking
If the arc is extinguished rapidly, there isnt enough filler metal present to avoid
forming a deep crater. The geometry of the crater intensifies the solidification
stresses in the area near the crater. If they are high enough, a crack forms in and
around the crater. Figure 6-1 shows a crater crack.
Figure 6-1: Radiograph Showing a Crater Crack
In order to eliminate crater cracking, the geometric discontinuity of the crater must
be minimized, i.e., the crater must be filled in as much as possible. There are
several methods to prevent crater cracking:
............................................................................................................................................................
Use a power supply with a crater fill option.

Rapidly restrike and extinguish the arc a few times while keeping the wire tip in
the crater. This will build up the crater.
Run the weld bead to the end of the workpiece, then reverse direction and
increase travel speed in the new travel direction.
Longitudinal Cracking
Longitudinal cracking occurs relatively frequently. Figure 6-2 shows a longitudinal
crack. Weld cracking can usually be eliminated by taking the following precautions:
Heat-treatable alloys are crack sensitive and will crack if welded autogenously.
Make sure you add filler metal.
Make sure you add enough filler metal in welding any alloy. Do not deposit thin,
concave groove welds or small or concave fillets. They may crack. Weld passes in
both groove welds and fillet welds should be convex.
If you encounter cracking in making a square butt weld, try a V-groove
preparation. It will allow the addition of more filler metal. Similarly, if youre
using a bevel prep, try a V-prep instead.
Reduce the clamping pressure to allow the material to move slightly during
solidification. High stress is occasionally caused by the joint geometry, which
may need to be changed.
Figure 6-2: Radiograph Showing Longitudinal Weld Cracking
Liquation Cracking
Liquation cracking is common in lap and fillet welds in thin heat-treatable alloys. It
is not usually seen in the nonheat-treatable alloys or in butt joints. It manifests
itself as a short, longitudinal crack in the parent material on the back side of a
weld. It is caused by the melting of low-melting-point compounds, which segregate
at the grain boundaries in heat-treatable alloys near the fusion boundaries in the
partial fusion zone. In order to minimize it, weld penetration into the parent metal
............................................................................................................................................................
needs to be controlled in lap and fillet welds. Welds having 30 or 40% penetration
into the parent metal will almost never cause a crack, while welds penetrating 70 80% into the parent metal will often cause a small crack on the back side of a weld.
Incomplete Penetration
Figure 6-3 shows a
weld with incomplete
penetration.
Incomplete
penetration is often
caused by insufficient
weld current at a travel
speed that is too high.
However, the use of an
arc voltage that is too
high can also result
Figure 6-3: Cross section of weld showing incomplete fusion
in the arc bridging
the weld root and not
penetrating completely. You should also take care when backgouging a twosided
weld. Insufficient backgouging can sometimes result in incomplete penetration. It is
sometimes surprising how deep the backgouge must go to get to sound metal.
Incomplete Fusion
Incomplete fusion, shown in Figure 6-4, is usually caused by welding over heavy
oxides, insufficient interpass cleaning or poor bead placement. Remove heavy
oxides before welding.
The weld smut
and oxides must
be removed before
making another weld
pass. Aluminum is
prone to develop fine
line Lack Of Fusion
(LOF) defects if proper
welding techniques
are not used and/or
proper preweld and /
or interpass cleaning
is not performed. Also
Figure 6-4: Cross section of weld showing lack of side wall fusion
to prevent LOF, GMAW
should not be performed in the short circuiting transfer mode. Such defects are
often very subtle and difficult to detect, even when radiography is used. Figure 6-4
shows such a LOF on the weld sidewall. In order to make it more visible, a red arrow
has been added to point out the LOF.
............................................................................................................................................................
Porosity
Figure 6-5 shows excessive porosity in a fracture
surface of a weld. Porosity in aluminum welds
is caused by hydrogen trapped in the welds as it
solidifies and cools. We have already explained
that the source of this hydrogen is oils, greases
or water vapor dissociated by the welding arc.
Eliminate the sources of these contaminants to
control weld porosity. It is also helpful to use an
upward progression when welding in the vertical
position rather than the typical downward
progression, as this helps minimize weld porosity.
Copper Contamination
Figure 6-5: Radiograph showing excessive porosity
Copper contamination will appear white on

a radiograph, as shown in Figure 6-6. Copper
contamination is usually larger and fuzzier
than tungsten, which appears as individual
small particles.
Copper contamination is often encountered in
GMAW and is caused when the wire burns back
and fuses to the copper contact tip. The copper
and aluminum quickly alloy and deposit copper
in the aluminum weld. If this occurs, the copper
contamination must be ground out and repaired
because the aluminum/copper alloy deposited is
very brittle.
Copper contamination can also be caused by
copper backing bars or copper tooling. While
the use of copper backing bars is acceptable, the
joint preparation must be such that the arc is
not allowed to directly strike the copper bar. If it
does, the copper bar will melt and alloy with the
aluminum. Using copper backing bars is acceptable,
but be sure to avoid wide root openings.
Figure 6-6: Radiograph Showing Copper Contamination

(Copper contamination shows up as a lighter and irregularly
shaped areas)
............................................................................................................................................................
Solving Problems in Qualifying Weld Procedures

Many fabricators encounter difficulties in qualifying welding procedures or
welders for aluminum. Most codes require the use of reduced section tensile tests
and guided bend tests for procedure qualification. Therefore, we will discuss these
two requirements.
Difficulties in Meeting Tensile Test Requirements
All codes have minimum tensile test values. Samples removed from procedure
qualification test plates must meet these values. However, the weld often does not
have to meet the same minimum requirements as the parent material. For example,
all codes require that 6061-T6 material have a minimum tensile strength of 40 ksi (276
MPa). Welds in 6061-T6 only have to meet 24 ksi (165 MPa) minimum. It is important
to understand what is required for the specific alloy being used. In general, the
minimum tensile properties required for nonheat-treatable alloys are those of the
annealed O temper base material. No such rule exists for the heat-treatable alloys.
Consult the applicable fabrication code to determine the minimum tensile properties
required for the alloy being used.
There are several reasons why samples fail tensile testing. For heat-treatable
alloys, it is usually because excessive heat input has been used. Common reasons
for excessive heat input include the following:
Use of excessive preheat. Preheat should be no more than 200F (93C) and isnt
needed unless the ambient temperature is below 32F (0C).
Interpass temperature that is too high. Maximum interpass temperature should
be 250F (121C).
Technique issues such as the use of very wide weave passes, which can cause
excessive heat input. Stringer passes should generally be used, although
weaving is acceptable as long as the weave width is no wider than four times
the wire diameter.
Weld defects can also cause premature tensile failures. Observe the fracture face of
the failed tensile sample. The presence of weld defects should be fairly obvious. Lack
of fusion or lack of penetration defects are especially prone to cause tensile failure.
Where the code requires the tensile sample to meet 40 ksi (276 MPa) minimum
tensile strength, the use of 5356 is not recommended. Higher strength filler alloys,
such as 5183 or 5556, are recommended for these applications.
............................................................................................................................................................
Difficulties in Meeting Bend Test Requirements

Most bend test failures are caused by the welders lack of familiarity with the bend
test requirements for aluminum welds. Some points to remember are as follows:
1. The ductility of aluminum welds is lower than that of steel welds. Ensure the
test radius is correct for the alloy under test. Figure 6-7 shows the bend test
requirements of AWS D1.2, which are the same as those in most fabrication codes.
AS REQUIRED
TAPPED HOLE TO SUIT

TESTING MACHINE
PLUNGER
3/4
(19)
AS REQUIRED
SHOULDER HARDENED
AND GREASED
1-1/8
(29)
3 MIN
(75 MIN)
1/4
(6)
1/2
(13)
3/4 (19)
3/4
(19)
2 MIN
(51 MIN)
1-1/8
(29)
6-3/4
(171)
R = 3/4
(19)
1/8
(3)
3/4
(19)
2
(51)
3-7/8
(98)
3/4
(19)
7 - 1/2
(191)
9
(229)
YOKE
HARDENED ROLLERS
1 - 1/2 in. (38)
IN DIAMETER MAY BE
SUBSTITUTED FOR
JIG SHOULDERS
NOTE: All dimensions in
Inches (mm)
Figure 6-7: AWS D1.2 Requirements
Table 6-1: AWS D1.2 Requirements

Thickness of Specimen in. (mm)
A in. (mm)
B in. (mm)
C in. (mm)
D in. (mm)
3/8 (10)
1-1/2 (38)
3/4 (19)
2-3/8 (60)
1-3/16 (30)
4t
2t
6t + 1/8 (3)
3t + 1/16 (1.6)
1/8 (3)
2-1/16 (52)
1-1/32 (26)
2-3/8 (60)
1-3/16 (30)
t <1/8 (<3)
16-1/2t
8-1/4t
18-1/2t + 1/16 (1.6)
9-1/4t + 1/32 (1)
3/8 (10)
2-1/2 (64)
1-1/4 (32)
3-3/8 (86)
1-11/16 (43)
6-2/3t
3-1/3t
8-2/3t + 1/8 (3)
4-1/3t + 1/16 (1.6)
3/8 (10)
3 (75)
1-1/2 (38)
3-7/8 (98)
1-15/16 (49)
8t
4t
10t + 1/8 (3)
5t + 1/16 (1.6)
Materials
M21 and M22
M23 and F23
Welds
M25 and
Annealed M23
M27 and
Annealed M24
............................................................................................................................................................
2. If the bend sample fails with little or no distortion before breaking, the most likely
cause is a defect in the weld. Any lack of fusion or insufficient penetration in the
weld will quickly open up on bending and cause the sample to break in half. A
visual examination of the fracture surface will reveal these defects.
3. Ensure the bend test sample preparation is correct.

a. Make sure grinding or machining marks go along the length of the sample, not
across it. Marks going across the sample can act as crack initiation sites.
b. Dont leave square corners on the sample. All codes allow a radius at the
corners of 1/2 the sample thickness or 1/4 in. (6.4 mm), whichever is less.
Adhering to this radius reduces the probability of initiating a crack in the corners.
4. Special precautions are necessary when testing welds in 6061 or other M23 (per
AWS) or P23 (per ASME Section IX) materials because of their limited ductility. In
recognition of this, both AWS D1.2 and ASME Section IX require bend test samples
in 6061 and other M23 materials to be machined to 1/8 in. (3.2 mm) thickness,
instead of the normal 3/8 in. (9.5 mm) thickness. If 6061 samples are machined
to 3/8 in. (9.5 mm) thickness and tested around a standard radius mandrel, they
often fail. AWS D1.2 alternatively allows samples in M23 materials to be machined
to 3/8 in. (9.5 mm) thick and annealed before testing, but ASME Section IX has no
such provision.
5. The use of the standard plunger-type bend tester is responsible for many bend
test failures. This test fixture works well for steel because the mechanical
properties of the weld, HAZ and parent material are all similar. However, in
aluminum, the HAZ is usually much weaker than the remainder of the sample.
If the sample is tested in a plungertype tester, the bend strain is concentrated
in the HAZ. Instead of bending smoothly around the mandrel, the sample often
forms a sharp kink at the HAZ and then fails at the kink.
A much better test for welded aluminum bend samples is the wraparound guided
bend test, shown in Figure 6-8. In this test, the sample is pulled around the mandrel
and forced to stay in contact with it. These test jigs are often made from rotary
tubing benders. Both AWS D1.2 and ASME Section IX encourage the use of these
testers for aluminum. The same is true of most of the rules of many maritime
societies such as the American Bureau of Shipping (ABS), Lloyds Register (LR),
Bureau Veritas (BV), Det Norske Veritas Germanischer Lloyd (DNV GL) and the like.
............................................................................................................................................................
t + 1/16 in.
(1.6 mm) MAX
ROLLER
B = (1/2) A
Figure 6-8: Wraparound Guided Bend Test
Table 6-2: Wraparound Guided Bend Test

Thickness of Specimen in. (mm)
A in. (mm)
B in. (mm)
3/8 (9.0)
1-1/2 (38.0)
3/4 (19.0)
4t
2t
1/8 (3.0)
2-1/16 (52.4)
1-1/32 (26.2)
t[<1/8] (3.0)
16-1/2t
8-1/4T
3/8 (9.0)
2-1/2 (63.5)
1-1/4 (31.8)
6-2/3t
3-1/3t
3/8 (9.0)
3 (76.2)
1-1/2 (38.0)
8t
4t
Materials
M21 and M22
M23 and F23 Welds
M25 and Annealed
M23
M27 and Annealed
M24
700
600
500
400
15
45
0.0
300
(1.
in.
m)
2m
0.06
10
m)
6m
. (1.
2 in
200
. (2
0.093 in
)
.4 mm
100
0
wire feed speed, meters per minute
20
800
0.0
30
0.0
in.
(0.8
35
mm
in.
)
(0.
9m
m)
wire feed speed, inches per minute
............................................................................................................................................................
0
0
50
100
150
200
250
300
350
400
450
welding current a (dcep)
600
in.
(1.
2
500
15
mm
)
700
45
0.0
400
6
0.0
300
200
m)
.6 m
. (1
n
i
2
. (2
0.093 in
10
)
.4 mm
100
0
wire feed speed, meters per minute
20
800
0.0
30 i
n. (0
.8 m
m)
0.0
35
in.
(0.9
mm
)
wire feed speed, inches per minute
Figure 6-9: Welding Current vs. WFS for ER4043 Aluminum Electrodes at a Fixed Stickout
0
0
50
100
150
200
250
300
350
400
450
welding current a (dcep)

Figure 6-10: Welding Current vs. WFS for ER5356 Aluminum Electrodes at a Fixed Stickout
............................................................................................................................................................
Joint Spacing
Joint Spacing
t
Temporary
Backing
(B)
t/4
2t
(A)
60-90
60-90
or
100
3/16
Joint Spacing
Joint Spacing
1/16 3/32
(C)
(D)
90
60
Joint Spacing
1/16 - 3/32
Temporary
Backing
Joint Spacing
1/2
(E)
1/16-3/32 t/4
(F)
60
Joint Spacing
1/16
t
t
1 1/2
1 1/2
up to 3/8
{ t3/8
for t> 3/8
up to 3/8
{ t3/8
for t> 3/8
Permanent
Backing
(G)
Permanent
Backing
(H)
60
(I)
t2
(J)
(K)
Figure 6-11: Welding Joint Designs for Aluminum GMAW Groove Welding Flat, Horizontal,
Vertical and Overhead
Aluminum GMAW Welding Parameters
............................................................................................................................................................
Table 6-3 specifies fillet joints; however, the parameters for aluminum GMAW
of groove joints will generally be the same as for fillet joints.
Table 6-3: Welding Guidelines for Aluminum GMAW
Proc
Material
Thickness
in. (mm)
Position
Joint
WFS
Trim or
(IPM) Current Power
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
0.035 (0.9)
CV
3/16 (4.8)
Horz.
Fillet
585
172.4
23.3
3/16 (4.8)
31.4
4043
0.035 (0.9)
CV
3/16 (4.8)
Vert. Up
Fillet
555
160.3
22.8
3/16 (4.8)
29.8
4043
0.035 (0.9)
CV
3/16 (4.8)
Overhead
Fillet
575
167.1
23
3/16 (4.8)
30.8
4043
0.035 (0.9)
CV
1/4 (6.4)
Horz.
Fillet
665
188.9
23.2
1/4 (6.4)
20.1
4043
0.035 (0.9)
CV
1/4 (6.4)
Vert. Up
Fillet
650
179.3
24.4
1/4 (6.4)
19.6
4043
0.035 (0.9)
CV
1/4 (6.4)
Overhead
Fillet
660
181.5
24.5
1/4 (6.4)
19.9
4043
0.035 (0.9)
3/16 (4.8)
Horz.
Fillet
585
190.9
26.1
3/16 (4.8)
31.4
3/16 (4.8)
Vert. Up
Fillet
550
172.1
4.05
23
3/16 (4.8)
29.5
3/16 (4.8)
Overhead
Fillet
535
168.1
23
3/16 (4.8)
28.7
1/4 (6.4)
Horz.
Fillet
670
201.7
5.35
26.5
1/4 (6.4)
20.2
1/4 (6.4)
Vert. Up
Fillet
640
197.7
5.11
25.8
1/4 (6.4)
19.3
0.035 (0.9)
Power
Mode
Power
Mode
Power
Mode
Power
Mode
Power
Mode
Power
Mode
4043
0.035 (0.9)
4043
0.035 (0.9)
4043
0.035 (0.9)
4043
0.035 (0.9)
4043
1/4 (6.4)
Overhead
Fillet
650
197
5.25
26.6
1/4 (6.4)
19.6
4043
0.035 (0.9)
Pulse
3/16 (4.8)
Horz.
Fillet
585
184
23.5
3/16 (4.8)
31.4
4043
0.035 (0.9)
Pulse
3/16 (4.8)
Vert. Up
Fillet
560
165.1
0.98
23
3/16 (4.8)
30
4043
0.035 (0.9)
Pulse
3/16 (4.8)
Overhead
Fillet
570
182.8
1.03
23.7
3/16 (4.8)
30.6
4043
0.035 (0.9)
Pulse
1/4 (6.4)
Horz.
Fillet
665
228.8
25.1
1/4 (6.4)
20.1
4043
0.035 (0.9)
Pulse
1/4 (6.4)
Vert. Up
Fillet
640
186.3
0.96
24.1
1/4 (6.4)
19.3
4043
0.035 (0.9)
Pulse
1/4 (6.4)
Overhead
Fillet
645
196.5
1.02
25.1
1/4 (6.4)
19.5
4043
3/64 (1.2)
CV
3/16 (4.8)
Horz.
Fillet
310
194.3
25
3/16 (4.8)
29.8
4043
3/64 (1.2)
CV
3/16 (4.8)
Vert. Up
Fillet
300
163.3
24.2
3/16 (4.8)
28.9
4043
3/64 (1.2)
CV
3/16 (4.8)
Overhead
Fillet
310
191.9
24.6
3/16 (4.8)
29.8
4043
3/64 (1.2)
CV
1/4 (6.4)
Horz.
Fillet
350
194.8
25.2
1/4 (6.4)
18.9
4043
3/64 (1.2)
CV
1/4 (6.4)
Vert. Up
Fillet
315
190
25
1/4 (6.4)
17
4043
3/64 (1.2)
CV
1/4 (6.4)
Overhead
Fillet
335
202.3
25.7
1/4 (6.4)
18.1
4043
3/64 (1.2)
CV
3/8 (9.5)
Horz.
Fillet
385
208.6
26.8
3/8 (9.5)
9.3
Alloy
Diameter
in. (mm)
4043
............................................................................................................................................................
Proc
Material
Thickness
in. (mm)
Position
Joint
3/64 (1.2)
CV
3/8 (9.5)
Vert. Up
4043
3/64 (1.2)
CV
3/8 (9.5)
Vert. Up
4043
3/64 (1.2)
CV
3/8 (9.5)
Overhead
4043
3/64 (1.2)
CV
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
Fillet
(root)
Fillet
(fill)
4043
3/64 (1.2)
3/16 (4.8)
Horz.
4043
3/64 (1.2)
Power
Mode
Power
Mode
3/16 (4.8)
4043
3/64 (1.2)
Power
Mode
4043
3/64 (1.2)
4043
3/64 (1.2)
Power
Mode
Power
Mode
4043
3/64 (1.2)
4043
3/64 (1.2)
4043
3/64 (1.2)
4043
3/64 (1.2)
4043
3/64 (1.2)
4043
Alloy
Diameter
in. (mm)
4043
WFS
Trim or
(IPM) Current Power
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
350
195.8
25.6
1/4 (6.4)
18.9
330
194.7
25.8
3/8 (9.5)
28.6
420
221.3
25.6
1/4 (6.4)
22.7
375
199.6
26.6
3/8 (9.5)
32.5
Fillet
300
180.6
4.6
24.6
3/16 (4.8)
28.9
Vert. Up
Fillet
270
161.5
27.7
3/16 (4.8)
26
3/16 (4.8)
Overhead
Fillet
290
179
4.25
23.4
3/16 (4.8)
27.9
1/4 (6.4)
Horz.
Fillet
360
203.6
5.4
26
1/4 (6.4)
19.5
1/4 (6.4)
Vert. Up
Fillet
315
193.8
4.95
25.5
1/4 (6.4)
17
Power
Mode
1/4 (6.4)
Overhead
Fillet
350
204.3
5.03
24.3
1/4 (6.4)
18.9
3/8 (9.5)
Horz.
Fillet
420
242.2
6.35
26.1
3/8 (9.5)
10.1
3/8 (9.5)
Vert. Up
209.3
5.65
26.1
1/4 (6.4)
19.8
3/8 (9.5)
Vert. Up
335
190
5.1
25.9
3/8 (9.5)
29
3/8 (9.5)
Overhead
420
229
5.95
25.6
1/4 (6.4)
22.7
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
Fillet
(root)
Fillet
(fill)
365
3/64 (1.2)
Power
Mode
Power
Mode
Power
Mode
Power
Mode
Power
Mode
340
200
5.3
26
3/8 (9.5)
29.4
4043
3/64 (1.2)
Pulse
3/16 (4.8)
Horz.
Fillet
325
159
0.98
23.2
3/16 (4.8)
31.3
4043
3/64 (1.2)
Pulse
3/16 (4.8)
Vert. Up
Fillet
305
150.9
22.8
3/16 (4.8)
29.3
4043
3/64 (1.2)
Pulse
3/16 (4.8)
Overhead
Fillet
320
181.2
1.09
24
3/16 (4.8)
30.8
4043
3/64 (1.2)
Pulse
1/4 (6.4)
Horz.
Fillet
360
200.5
1.05
24.3
1/4 (6.4)
19.5
4043
3/64 (1.2)
Pulse
1/4 (6.4)
Vert. Up
Fillet
320
163.4
1.06
23.6
1/4 (6.4)
17.3
4043
3/64 (1.2)
Pulse
1/4 (6.4)
Overhead
Fillet
360
204.2
1.1
24.7
1/4 (6.4)
19.5
4043
3/64 (1.2)
Pulse
3/8 (9.5)
Horz.
Fillet
500
269.6
1.05
27.4
3/8 (9.5)
12
4043
3/64 (1.2)
Pulse
3/8 (9.5)
Vert. Up
Fillet
(root)
425
217.2
0.98
24.5
1/4 (6.4)
23
4043
3/64 (1.2)
Pulse
3/8 (9.5)
Vert. Up
Fillet
(fill)
350
170
1.06
24.3
3/8 (9.5)
30.3
............................................................................................................................................................
Proc
Material
Thickness
in. (mm)
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
Position
Joint
3/64 (1.2)
Pulse
3/8 (9.5)
Overhead
420
226.3
4043
3/64 (1.2)
Pulse
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
0.96
24.3
1/4 (6.4)
22.7
385
195.5
1.08
25
3/8 (9.5)
33.3
4043
1/16 (1.6)
CV
1/4 (6.4)
Horz.
Fillet
225
233.6
24.5
1/4 (6.4)
21.6
4043
1/16 (1.6)
CV
1/4 (6.4)
Vert. Up
Fillet
190
197.3
23.8
1/4 (6.4)
18.3
4043
1/16 (1.6)
CV
1/4 (6.4)
Overhead
Fillet
205
212.4
24.8
1/4 (6.4)
19.7
4043
1/16 (1.6)
CV
3/8 (9.5)
Horz.
Fillet
250
240
24
3/8 (9.5)
10.7
4043
1/16 (1.6)
CV
3/8 (9.5)
Vert. Up
Fillet
(root)
200
192
22
3/8 (9.5)
25.7
4043
1/16 (1.6)
CV
3/8 (9.5)
Vert. Up
Fillet
(fill)
200
185
23.6
3/8 (9.5)
25.7
4043
1/16 (1.6)
CV
3/8 (9.5)
Overhead
Fillet
225
240
26
3/8 (9.5)
9.6
4043
1/16 (1.6)
1/4 (6.4)
Horz.
Fillet
225
240
6.3
25.7
1/4 (6.4)
21.6
4043
1/16 (1.6)
1/4 (6.4)
Vert. Up
Fillet
180
195
5.05
25.7
1/4 (6.4)
17.3
4043
1/16 (1.6)
Power
Mode
Power
Mode
Power
Mode
1/4 (6.4)
Overhead
Fillet
200
225
5.8
25.3
1/4 (6.4)
19.2
4043
1/16 (1.6)
3/8 (9.5)
Horz.
Fillet
250
250
6.8
26.8
3/8 (9.5)
10.7
4043
1/16 (1.6)
3/8 (9.5)
Vert. Up
Fillet
200
225
26.3
3/8 (9.5)
8.6
4043
1/16 (1.6)
Power
Mode
Power
Mode
Power
Mode
3/8 (9.5)
Overhead
Fillet
225
240
6.35
26
3/8 (9.5)
9.6
4043
1/16 (1.6)
Pulse
1/4 (6.4)
Horz.
Fillet
225
226
1.05
23.6
1/4 (6.4)
21.6
4043
1/16 (1.6)
Pulse
1/4 (6.4)
Vert. Up
Fillet
180
160
1.1
23.6
1/4 (6.4)
17.3
4043
1/16 (1.6)
Pulse
1/4 (6.4)
Overhead
Fillet
200
195
1.1
23.2
1/4 (6.4)
19.2
4043
1/16 (1.6)
Pulse
3/8 (9.5)
Horz.
Fillet
250
225
1.1
25
3/8 (9.5)
10.7
4043
1/16 (1.6)
Pulse
3/8 (9.5)
Vert. Up
Fillet
200
200
1.1
23
3/8 (9.5)
8.6
4043
1/16 (1.6)
Pulse
3/8 (9.5)
Overhead
Fillet
225
220
1.1
24
3/8 (9.5)
9.6
5356
0.035 (0.9)
CV
3/16 (4.8)
Horz.
Fillet
770
185.3
21.6
3/16 (4.8)
41.3
5356
0.035 (0.9)
CV
3/16 (4.8)
Vert. Up
Fillet
750
183
22
3/16 (4.8)
40.2
5356
0.035 (0.9)
CV
3/16 (4.8)
Overhead
Fillet
775
184.7
22.2
3/16 (4.8)
41.6
Alloy
Diameter
in. (mm)
4043
WFS
Trim or
(IPM) Current Power
............................................................................................................................................................
Proc
Material
Thickness
in. (mm)
Position
Joint
WFS
Trim or
(IPM) Current Power
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
0.035 (0.9)
CV
1/4 (6.4)
Horz.
Fillet
800
201.7
23.6
1/4 (6.4)
24.1
5356
0.035 (0.9)
CV
1/4 (6.4)
Vert. Up
Fillet
750
183
22.4
1/4 (6.4)
22.6
5356
0.035 (0.9)
CV
1/4 (6.4)
Overhead
Fillet
800
199.5
23.4
1/4 (6.4)
24.1
5356
0.035 (0.9)
3/16 (4.8)
Horz.
5356
0.035 (0.9)
3/16 (4.8)
5356
0.035 (0.9)
Power
Mode
Power
Mode
Power
Mode
Fillet
770
186.7
4.25
22.6
3/16 (4.8)
41.3
Vert. Up
Fillet
750
180
22
3/16 (4.8)
40.2
3/16 (4.8)
Overhead
Fillet
775
191
4.2
21.8
3/16 (4.8)
41.6
5356
0.035 (0.9)
Power
Mode
1/4 (6.4)
Horz.
Fillet
800
203
4.96
24.1
1/4 (6.4)
24.1
5356
0.035 (0.9)
1/4 (6.4)
Vert. Up
Fillet
750
189
4.3
22.7
1/4 (6.4)
22.6
0.035 (0.9)
Power
Mode
Power
Mode
5356
1/4 (6.4)
Overhead
Fillet
800
197.6
4.75
23.3
1/4 (6.4)
24.1
5356
0.035 (0.9)
Pulse
3/16 (4.8)
Horz.
Fillet
770
172.7
0.82
21
3/16 (4.8)
41.3
5356
0.035 (0.9)
Pulse
3/16 (4.8)
Vert. Up
Fillet
750
176
0.87
21.8
3/16 (4.8)
40.2
5356
0.035 (0.9)
Pulse
3/16 (4.8)
Overhead
Fillet
775
188
0.94
23.6
3/16 (4.8)
41.6
5356
0.035 (0.9)
Pulse
1/4 (6.4)
Horz.
Fillet
510
216
0.98
23.3
1/4 (6.4)
15.4
5356
0.035 (0.9)
Pulse
1/4 (6.4)
Vert. Up
Fillet
500
212.2
0.84
21.8
1/4 (6.4)
15.1
5356
0.035 (0.9)
Pulse
1/4 (6.4)
Overhead
Fillet
510
219.9
23.4
1/4 (6.4)
15.4
5356
3/64 (1.2)
CV
3/16 (4.8)
Horz.
Fillet
470
209
21.6
3/16 (4.8)
45.2
5356
3/64 (1.2)
CV
3/16 (4.8)
Vert. Up
Fillet
430
190
20.9
3/16 (4.8)
41.4
5356
3/64 (1.2)
CV
3/16 (4.8)
Overhead
Fillet
475
206
21.6
3/16 (4.8)
45.7
5356
3/64 (1.2)
CV
1/4 (6.4)
Horz.
Fillet
500
208
23
1/4 (6.4)
27.1
5356
3/64 (1.2)
CV
1/4 (6.4)
Vert. Up
Fillet
460
192.1
20.4
1/4 (6.4)
24.9
5356
3/64 (1.2)
CV
1/4 (6.4)
Overhead
Fillet
480
196.8
21.5
1/4 (6.4)
26
5356
3/64 (1.2)
CV
3/8 (9.5)
Horz.
Fillet
610
275.2
25.5
3/8 (9.5)
14.7
5356
3/64 (1.2)
CV
3/8 (9.5)
Vert. Up
Fillet
(root)
440
192.4
22.9
1/4 (6.4)
23.8
5356
3/64 (1.2)
CV
3/8 (9.5)
Vert. Up
Fillet
(fill)
410
186.2
23.7
3/8 (9.5)
35.5
Alloy
Diameter
in. (mm)
5356
............................................................................................................................................................
Proc
Material
Thickness
in. (mm)
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
Position
Joint
3/64 (1.2)
CV
3/8 (9.5)
Overhead
450
200
5356
3/64 (1.2)
CV
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
23.7
1/4 (6.4)
24.4
435
188.8
23.5
3/8 (9.5)
37.7
5356
3/64 (1.2)
3/16 (4.8)
Horz.
Fillet
5356
3/64 (1.2)
3/16 (4.8)
Vert. Up
5356
3/64 (1.2)
3/16 (4.8)
5356
3/64 (1.2)
Power
Mode
Power
Mode
Power
Mode
Power
Mode
450
205
4.5
21
3/16 (4.8)
43.3
Fillet
430
200
4.15
21
3/16 (4.8)
41.4
Overhead
Fillet
475
207
4.55
21.8
3/16 (4.8)
45.7
1/4 (6.4)
Horz.
Fillet
475
240
5.8
25
1/4 (6.4)
25.7
5356
3/64 (1.2)
Power
Mode
1/4 (6.4)
Vert. Up
Fillet
460
210
4.65
22
1/4 (6.4)
24.9
5356
3/64 (1.2)
1/4 (6.4)
Overhead
Fillet
490
240
5.9
24.5
1/4 (6.4)
26.5
3/64 (1.2)
Power
Mode
Power
Mode
5356
3/8 (9.5)
Horz.
Fillet
600
260
27
3/8 (9.5)
14.4
5356
3/64 (1.2)
Power
Mode
3/8 (9.5)
Vert. Up
Fillet
(root)
520
214.5
4.65
21.4
3/8 (9.5)
12.5
5356
3/64 (1.2)
Power
Mode
3/8 (9.5)
Vert. Up
Fillet
(fill)
500
204.5
4.7
22.5
3/8 (9.5)
12
5356
3/64 (1.2)
3/8 (9.5)
Overhead
236
5.65
23.3
3/8 (9.5)
13.1
3/64 (1.2)
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
545
5356
Power
Mode
Power
Mode
525
226
5.5
24.2
3/8 (9.5)
12.6
5356
3/64 (1.2)
Pulse
3/16 (4.8)
Horz.
Fillet
470
200.6
0.94
21.8
3/16 (4.8)
45.2
5356
3/64 (1.2)
Pulse
3/16 (4.8)
Vert. Up
Fillet
430
185.5
0.94
20.5
3/16 (4.8)
41.4
5356
3/64 (1.2)
Pulse
3/16 (4.8)
Overhead
Fillet
475
200
0.94
21.7
3/16 (4.8)
45.7
5356
3/64 (1.2)
Pulse
1/4 (6.4)
Horz.
Fillet
510
216
0.98
23.3
1/4 (6.4)
27.6
5356
3/64 (1.2)
Pulse
1/4 (6.4)
Vert. Up
Fillet
500
212.2
0.84
21.8
1/4 (6.4)
27.1
5356
3/64 (1.2)
Pulse
1/4 (6.4)
Overhead
Fillet
500
219.9
23.4
1/4 (6.4)
27.1
5356
3/64 (1.2)
Pulse
3/8 (9.5)
Horz.
Fillet
610
271.9
24.9
3/8 (9.5)
14.7
5356
3/64 (1.2)
Pulse
3/8 (9.5)
Vert. Up
475
192.9
0.9
21.7
1/4 (6.4)
25.7
5356
3/64 (1.2)
Pulse
3/8 (9.5)
Vert. Up
425
180.8
1.05
22.8
3/8 (9.5)
36.8
5356
3/64 (1.2)
Pulse
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
Fillet
(root)
520
208.4
0.9
22.6
1/4 (6.4)
28.1
5356
3/64 (1.2)
Pulse
3/8 (9.5)
Overhead
Fillet
(fill)
465
195
1.05
23.7
3/8 (9.5)
40.3
Alloy
Diameter
in. (mm)
5356
WFS
Trim or
(IPM) Current Power
............................................................................................................................................................
Proc
Material
Thickness
in. (mm)
Position
Joint
WFS
Trim or
(IPM) Current Power
Voltage
Weld
Size
in. (mm)
# of
Passes
Travel
Speed
(IPM)
1/16 (1.6)
CV
1/4 (6.4)
Horz.
Fillet
330
265
22.6
1/4 (6.4)
31.7
5356
1/16 (1.6)
CV
1/4 (6.4)
Vert. Up
Fillet
285
222
21.5
1/4 (6.4)
27.4
5356
1/16 (1.6)
CV
1/4 (6.4)
Overhead
Fillet
310
235
24.4
1/4 (6.4)
29.8
5356
1/16 (1.6)
CV
3/8 (9.5)
Horz.
Fillet
360
278.5
24.8
3/8 (9.5)
15.4
5356
1/16 (1.6)
CV
3/8 (9.5)
Vert. Up
300
240
22.4
1/4 (6.4)
28.9
Vert. Up
Fillet
(root)
Fillet
(fill)
5356
1/16 (1.6)
CV
3/8 (9.5)
290
230
22.4
3/8 (9.5)
44.6
5356
1/16 (1.6)
CV
3/8 (9.5)
Overhead
Fillet
(root)
330
257.5
23.3
1/4 (6.4)
31.7
5356
1/16 (1.6)
CV
3/8 (9.5)
Overhead
Fillet
(fill)
300
250
24
3/8 (9.5)
46.2
5356
1/16 (1.6)
Power
Mode
1/4 (6.4)
Horz.
Fillet
340
264
6.2
23.3
1/4 (6.4)
32.7
5356
1/16 (1.6)
Power
Mode
1/4 (6.4)
Vert. Up
Fillet
300
230
22
1/4 (6.4)
28.9
5356
1/16 (1.6)
1/4 (6.4)
Overhead
Fillet
310
243
5.45
22.3
1/4 (6.4)
29.8
5356
1/16 (1.6)
3/8 (9.5)
Horz.
Fillet
360
287
7.7
26.5
3/8 (9.5)
15.4
5356
1/16 (1.6)
3/8 (9.5)
Vert. Up
240
5.3
21.4
1/4 (6.4)
29.8
1/16 (1.6)
3/8 (9.5)
Vert. Up
295
237
5.35
22.3
3/8 (9.5)
45.4
5356
1/16 (1.6)
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
Fillet
(root)
310
5356
Power
Mode
Power
Mode
Power
Mode
Power
Mode
Power
Mode
330
256
5.65
21.9
1/4 (6.4)
31.7
5356
1/16 (1.6)
Power
Mode
3/8 (9.5)
Overhead
Fillet
(fill)
310
245
5.5
22.1
3/8 (9.5)
47.7
5356
1/16 (1.6)
Pulse
1/4 (6.4)
Horz.
Fillet
335
251
0.98
23.5
1/4 (6.4)
32.2
5356
1/16 (1.6)
Pulse
1/4 (6.4)
Vert. Up
Fillet
270
207
1.02
20.3
1/4 (6.4)
26
5356
1/16 (1.6)
Pulse
1/4 (6.4)
Overhead
Fillet
305
232
1.05
22
1/4 (6.4)
29.3
5356
1/16 (1.6)
Pulse
3/8 (9.5)
Horz.
Fillet
360
280
1.08
24.7
3/8 (9.5)
15.4
5356
1/16 (1.6)
Pulse
3/8 (9.5)
Vert. Up
300
220
0.96
21
1/4 (6.4)
28.9
5356
1/16 (1.6)
Pulse
3/8 (9.5)
Vert. Up
295
225
1.05
21.3
3/8 (9.5)
45.4
5356
1/16 (1.6)
Pulse
3/8 (9.5)
Overhead
Fillet
(root)
Fillet
(fill)
Fillet
(root)
330
250
21.6
1/4 (6.4)
31.7
5356
1/16 (1.6)
Pulse
3/8 (9.5)
Overhead
Fillet
(fill)
305
237
1.1
22
3/8 (9.5)
47
Alloy
Diameter
in. (mm)
5356
............................................................................................................................................................
Welding Safety Instructions
............................................................................................................................................................
Welding Safety Checklist

HAZARD
FACTORS TO CONSIDER
Electric shock can kill
Wetness
Welder in or on workpiece
Confined space
Electrode holder and
cable insulation
Fumes and gases can be dangerous
Confined area
Positioning of welders head
Lack of general ventilation
Electrode types, i.e., manganese,
chromium, etc. See MSDS
Base metal coatings,
galvanize, paint
Welding sparks can cause fire

or explosion
Containers which have held
combustibles
Flammable materials
Arc rays can burn eyes and skin

Process: gas-shielded arc
most severe
Confined space
Metal enclosure
Wetness
Restricted entry
Heavier than air gas
Welder inside or on workpiece
PRECAUTION SUMMARY
Insulate welder from workpiece and ground using dry insulation.

Rubber mat or dry wood.
Wear dry, hole-free gloves. (Change as necessary to keep dry.)
Do not touch electrically hot parts or electrode with bare skin or
wet clothing.
If wet area and welder cannot be insulated from workpiece with
dry insulation, use a semiautomatic, constant voltage welder or
stick welder with voltage reducing device.
Keep electrode holder and cable insulation in good condition. Do
not use if insulation is damaged or missing.
Use ventilation or exhaust to keep air breathing zone
clear, comfortable.
Use helmet and positioning of head to minimize fume in
breathing zone.
Read warnings on electrode container and material safety data
sheet (MSDS) for electrode.
Provide additional ventilation/exhaust where special
ventilation requirements exist.
Use special care when welding in a confined area.
Do not weld unless ventilation is adequate.
Do not weld on containers which have held combustible
materials (unless strict AWS F4.1 procedures are followed).
Check before welding.
Remove flammable materials from welding area or shield from
sparks, heat.
Keep a fire watch in area during and after welding.
Keep a fire extinguisher in the welding area.
Wear fire retardant clothing and hat. Use earplugs when
welding ovehead.
Select a filter lens which is comfortable for you while welding.

Always use helmet when welding.
Provide non-flammable shielding to protect others.
Wear clothing which protects skin while welding.
Carefully evaluate adequacy of ventilation especially where

electrode requires special ventilation or where gas may displace
breathing air.
If basic electric shock precautions cannot be followed to insulate
welder from work and electrode, use semiautomatic, constant
voltage equipment with cold electrode or stick welder with
voltage reducing device.
Provide welder helper and method of welder retrieval from
outside enclosure.
Welding Safety Instructions
............................................................................................................................................................
Welding Safety Checklist

HAZARD
FACTORS TO CONSIDER
PRECAUTION SUMMARY
General work area hazards
Cluttered area
Keep cables, materials, tools neatly organized.
Indirect work (welding

ground) connection
Connect work cable as close as possible to area where welding is

being performed. Do not allow alternate circuits through scaffold
cables, hoist chains, ground leads.
Electrical equipment
Use only double insulated or properly grounded equipment.

Always disconnect power to equipment before servicing.
Engine-driven equipment
Gas cylinders
Use in only open, well ventilated areas.

Keep enclosure complete and guards in place.
See Lincoln Electric service shop if guards are missing.
Refuel with engine off.
Is using auxiliary power, osha may require gfi protection or assured
grounding program (or isolated windings if less than 5kw).
Never touch cylinder with the electrode.

Never lift a machine with cylinder attached.
Keep cylinder upright and chained to support.
CUSTOMER ASSISTANCE POLICY

The business of The Lincoln Electric Company is manufacturing and selling high
quality welding equipment, consumables, and cutting equipment. Our challenge
is to meet the needs of our customers and to exceed their expectations. On
occasion, purchasers may ask Lincoln Electric for information or advice about
their use of our products. Our employees respond to inquiries to the best of
their ability based on information provided to them by the customers and the
knowledge they may have concerning the application. Our employees, however,
are not in a position to verify the information provided or to evaluate the
engineering requirements for the particular weldment. Accordingly, Lincoln
Electric does not warrant or guarantee or assume any liability with respect to
such information or advice. Moreover, the provision of such information or advice
does not create, expand, or alter any warranty on our products. Any express or
implied warranty that might arise from the information or advice, including any
implied warranty of merchantability or any warranty of fitness for any customers
particular purpose is specifically disclaimed.
Lincoln Electric is a responsive manufacturer, but the selection and use of
specific products sold by Lincoln Electric is solely within the control of, and
remains the sole responsibility of the customer. Many variables beyond the
control of Lincoln Electric affect the results obtained in applying these types of
fabrication methods and service requirements.
Subject to Change This information is accurate to the best of our knowledge
at the time of printing. Please refer to www.lincolnelectric.com for any
updated information.
THE LINCOLN ELECTRIC COMPANY

22801 St. Clair Avenue Cleveland, OH 44117-1199 U.S.A.
PH: +1.216.481.8100 www.lincolnelectric.com
Publication C8.100
Issue Date 01/16 The Lincoln Electric Co. All Rights Reserved

Al Welding

Uploaded by

Copyright:

Available Formats

Al Welding

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Al Welding

Uploaded by

Copyright:

Available Formats

About The Lincoln Electric Company

Lincoln Electric is the worlds leading manufacturer of welding equipment and

THATS LINCOLN ELECTRIC.

Lincoln Electrics SuperGlaze Technology

Sample defect from spool of competitive product

SuperGlaze Best in Class

LET US PUT OUR EXPERIENCE TO WORK FOR YOU

Lincoln Electrics SuperGlaze Technology

WHAT MAKES SUPERGLAZE STAND OUT FROM THE REST?

About The Lincoln Electric Company ................................................................................ 2

1.1 WELDING ALUMINUM VS. WELDING STEEL

1.2.1 ALUMINUM ALLOYS

1.2.2 WROUGHT ALLOYS

Main Alloying Elements

Copper (sometimes with magnesium)

Manganese (sometimes with magnesium)

Magnesium plus silicon

Zinc (sometimes with magnesium & copper)

1.2.3 CAST ALLOYS

Main Alloying Elements

Copper (sometimes with magnesium)

Silicon plus magnesium

1.3 ALLOYING ELEMENTS

In addition to the primary aluminum alloying elements, there are a number of

1.4 TEMPER DESIGNATIONS

1.4.1 NONHEAT-TREATABLE ALLOYS STRAIN-HARDENED DESIGNATIONS

YIELD STRENGTH (ksi)

PERCENT COLD WORK

Strain Hardened Only

Strain Hardened and Partially Annealed

Strain Hardened and Stabilized

Second Digit Indicates Degree of Strain Hardening

1.4.2 HEAT-TREATABLE ALLOYS

Effects of Welding on Aluminum Alloys

As before, it is easiest to discuss the effects of welding on the mechanical

2.1 NONHEAT-TREATABLE ALLOYS

2.2 HEAT-TREATABLE ALLOYS

Effects of Welding on Aluminum Alloys

Note the following:

If the weldment in either T4 or T6 material is post-weld aged, the strength of

DISTANCE FROM FUSION ZONE (cm)

Effects Of Welding On Aluminum Alloys

Filler Metal Selection

3.1 ALUMINUM FILLER ALLOYS

Freedom from hot cracking

Filler Metal Selection

Table 3-1: Wire Chemical Composition for Common Aluminum Wires

ER1100 & Alloy 1050

NOTE: Single values are maximum, except aluminum.

Filler Metal Selection

High Temperature Applications Al-Mg alloys with Mg content over 3%

5454 This alloy is a lower Mg alloy specifically developed to be immune to the

Table 3-2: Aluminum Product Selection Guide

Filler Metal Selection

Figure 3-1: SuperGlaze Aluminum GMAW Wire

Table 3-3: Comparison of Filler Metals 4043 and 5356

Smooth Bead, Good Wetting

Black Smut, Distinct Ripples

Lower Column Strength

More Prone to Porosity