Green Guide Growing

February 2014
State of Victoria through the Department of Environment and Primary Industries 2014
Except for any logos, emblems and trademarks, this work (Growing Green Guide: A guide to green roofs, walls and facades in Melbourne and Victoria, Australia) is licensed
under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 Australia licence, to the extent that it is protected by copyright. Authorship of this work must be
attributed to the State of Victoria, through the VAS Partnership, the Inner Melbourne Action Plan and the University of Melbourne. To view a copy of this licence, visit
http://creativecommons.org/licenses/by-nc-sa/4.0/
National Library of Australia Cataloguing-in-Publication data
Growing Green Guide: A guide to green roofs, walls and facades in Melbourne and Victoria, Australia
ISBN 978-1-74326-714-1 (Print)
ISBN 978-1-74326-715-8 (pdf)
Trademarks acknowledgment
Terms mentioned in this report that are known to be trademarks, whether registered or unregistered, have been indicated. Where trademarks are registered in Australia, this
has been noted by the addition of the symbol. The symbol is used where a mark is not registered. While all care has been taken in identifying trademarks in this guide,
users should rely on their own inquiries to determine ownership of trademarks, whether registered or unregistered, and the goods and services on which a mark is used or
which are covered by any registration.
Disclaimer
The information published in this guide is provided by the Growing Green Guide
partners to disseminate information in regards to the design, construction and
maintenance of green roofs, walls and facades. It is not, and does not purport to be,
a complete guide and is not a substitute for professional advice.
The design, construction and installation of green roofs, walls and facades is subject
to the relevant authorities granting the required permits, approvals and consents;
specific information should therefore be obtained from such authorities prior to the
commencement of any such projects.
The Growing Green Guide project partners (City of Melbourne, City of Stonnington,
City of Yarra, City of Port Phillip, the State of Victoria and The University of
Melbourne) and their employees do not guarantee that the publication is without
flaw of any kind or is wholly appropriate for your particular purposes, and therefore
disclaims all liability for any error, loss or other consequence which may arise from
you relying on any information in this publication.
Reference to any organisation in this guide is not to be construed as an endorsement
or recommendation of any information, goods or services supplied by that
organisation.
The Growing Green Guide partners accept no responsibility to you or anyone else
arising from any act or omission of any third party referred to in this booklet or any
loss, including damage or injury, when using and/or obtaining information, goods or
services.
The information contained in this guide is based on information available at the time
of writing. It is liable to change and we do not and cannot guarantee its currency.
The project partners reserve the right to make changes to the guide at any time.
Foreword
by Sidonie Carpenter
Sidonie co-founded Green Roofs Australasia, the peak body

for the green roof, wall and facade industry in 2007. She was
president of the association for almost four years and is
currently the board member for Queensland. Sidonie has
a landscape architecture practice in Brisbane.
Building one green roof will provide benefits for a small number of people and the local environment, but developing this Growing Green
Guide provides the knowledge and confidence to implement innovative and good quality green roofs and walls for years to come. It is
what the green roof and wall industry needs in able to plan, design and maintain quality green roof and wall systems throughout Australia.
Green Roofs Australasia was founded in 2007 as the industry body to promote and support the case for green roofs and walls. It is with
the development of Australian guidelines such as the Growing Green Guide that we will see the industry grow and strengthen.
Cities around the world have found green roof support and development has strengthened following the publication of how-to guides
like this.
Given the predicted impact that climate change and population growth will have on our urban environment, can we afford not to invest
in these types of sustainable solutions? Green roofs and walls provide a wide range of environmental, economic and social benefits, both
public and private. They can reduce urban heat loadings and stormwater run-off, increase the energy efficiency and liveability of buildings,
provide a range of habitat outcomes and even produce food. These guidelines will help to develop an understanding of the technology
and build knowledge about the benefits and methods of green roof/wall/facade design, construction and maintenance for all sectors of
the industry.
The guidelines have been written for Melbourne and Victoria but much of this information has national and international relevance.
The Growing Green Guide team has issued an open invitation to others to use the guidelines contents to develop additional resources,
or even produce a second version through their Creative Commons licensing.
This guide is only one of three main outputs developed by the Growing Green Guide project team a policy options paper and
feasibility study and design for four demonstration sites have also been completed. I encourage you to look at the Growing Green Guide
website: www.growinggreenguide.org. Here you will find the comprehensive policy options paper for use by government and others in
developing policies to encourage green roofs and walls and an opportunities assessment for demonstration green roof and wall sites in
each partner councils municipality.
With these guidelines, I look forward to seeing the number of green roofs, walls and facades increase across Victoria and Australia, and
I encourage you to read the sections that are relevant to you. While the publication of the guidelines marks the completion of the
Growing Green Guide teams planned work, this is not the end of the Growing Green Guide project; it is the start of mainstreaming green
roofs and walls into our built environment.
I congratulate the Inner Melbourne Action Plan (IMAP) councils of Melbourne, Port Phillip, Stonnington and Yarra, along with the State
Government of Victoria and The University of Melbourne, on the delivery of this project and hope to see the guidelines further
developed in coming years as we learn more about how these systems can deliver long term sustainable solutions across Australia.
Foreword
Preface
ii
Acknowledgements
SECTION
iii
Introduction
01
Introduction
02
Figure 1. Pressure builds over our cities
03
Figure 2. Vegetation can be added to a building
04
Definitions
04
08
Frequently asked questions
11
Benefits of green roofs, walls and facades
SECTION
02
Evidence
Reducing the energy budget of a building
15
Figure 3. Sensible heat flux under different roof treatments and albedo
15
Figure 4. Effect of a green roof on heat transfer for different types of roof construction
16
Figure 5. A comparison of thermal effects on a green roof under different types of

vegetation cover
16
Figure 6. Heating and cooling energy demand in a room under a bare and a green roof 17
Figure 7. Internal room temperatures under different roof types
18
Table 1. Effect of a green facade on building thermal performance
19
Contribution to urban cooling
20
Managing stormwater volume
21
Figure 8. Theoretical graph comparing stormwater run-off from a bare roof and
green roof
Figure 9. Rainfall retention under three roof treatments for rain events of
different intensity
Figure 10. Rainfall retained by different types of green roofs
21
22
22
Figure 11. Rainfall retention on green roofs with different slopes
23
Figure 12. Rainfall retention on a green roof under different rainfall scenarios
23
Improving stormwater quality
24
Table 2. Comparison of nitrogen (N) and phosphorus (P) content in rainwater

and run-off from bare roofs and green roofs (modular boxes)
24
Table 3. Comparison of nitrogen (N) and phosphorus (P) content in rainwater

and run-off from bare roofs and green roofs (vegetated mat)
Urban air quality
25
Human health and wellbeing
26
Property value
26
Green roof research at the University of Melbourne
27
1. Introduction
30
2. Site Analysis
31
SECTION
03
24
Technical Guide
2.1 Climatic factors on-site

2.2 Weight loading
32
34
Table 4. Weight loadings for some representative climbing species

Table 5. Green roof vegetation weight loadings
34
35
2.3 Drainage
36
Figure 13. Different types of roof drains

Figure 14. Water ponding on a roof
36
36
2.4 Existing structure and size

2.5 Access
2.6 Nearby vegetation
2.7 Site assessment summary
37
37
37
38
Table 6. Site analysis requirements
38
3. Design and Planning
39
3.1 Design objectives
41
Green roofs for biodiversity

Urban food production
43
44
3.2 Planning for drainage and irrigation

3.3 Designing for maintenance
3.4 Sourcing skills, expertise and information
3.5 Cost considerations

3.6 Planning, regulations and local laws
3.7 Building rating schemes and planning assessment tools
3.8 Selecting plants
45
46
46
48
50
51
52
Figure 15. The substrate depth on a green roof influences the plant types
that can be used
Table 7. Suitable plants for green roofs in Victoria
Table 8. Suitable plants for green walls in Victoria
Figure 16. Climbing plants used on green facades
Table 9. Suitable plants for green facades in Victoria
53
56
59
60
61
3.9 Designing for plant establishment
62
4. Building and Installation - General Advice
63
4.1 Occupational Health and Safety
64
Figure 17. Occupational Health and Safety legislative framework in Victoria
64
4.2 Insurance and system warranties
65
4.3 Project completion
65
5. Building and Installation - Green Roofs
66
Figure 18. Layers of a green roofs
67
5.1 Roof deck

5.2 Waterproofing
68
69
Table 10. Common waterproofing treatments
70
5.3 Protection layers
71
Root barrier

Protection mat
71
71
5.4 Drainage layer

5.5 Filter sheet
5.6 Growing substrate
5.7 Vegetation
72
72
73
74
Figure 19. Tree anchoring systems
75
5.8 Thermal insulation

5.9 Leak detection
5.10 Irrigation
75
76
77
Table 11. Irrigation methods for green roofs
78
5.11 Wind considerations

5.12 Slopes and wind protection
78
79
Figure 20. Layers of a sloped roof
79
5.13 Hard landscape elements
80
Figure 21. Functional elements on a green roof
81
Stages of construction: Building the City of Monash green roof
82
6. Building and Installation - Green Walls
83
6.1 Structures and components for green wall systems
84
Figure 22. Types of green wall configurations
84
6.2 Waterproofing
6.3 Irrigation and plant nutrition
6.4 Vegetation
6.5 Special considerations for walls
85
86
87
87
7. Building and Installation - Green Facades
88
7.1 Wall protection and different facade treatments
89
Figure 23. Support structures for green facades grown with twining climbers
89
7.2 Soils and growing substrates

7.3 Vegetation
7.4 Drainage and irrigation
90
90
91
8. Maintenance
92
8.1 Maintenance planning

8.2 Maintenance tasks
93
94
Table 12. Common maintenance tasks
95
8.3 Plant nutrition
96
SECTION
04
Victorian Case Studies
The Venny Green Roof
100
The Triptych Green Wall
103
RMIT University Building 21 Green Facade
106
Freshwater Place Green Roof
108
Minifie Park Green Roof
111
Victorian Desalination Project Green Roof
114
Burnley Biodiversity Green Roof
117
Kangan Institute Green Roof
120
Growing Up Rooftop Garden
122
Appendix A
125
Green roof growing substrates
126
Table 13: Properties that should be specified in growing substrates

Figure 24. A comparison of growing substrates
Table 14. Properties of green roof growing substrates
Table 15. Comparison of materials used in green roof growing substrates & their
saturated bulk density
126
127
128
128
Glossary
129
References and source material
130
ii
Preface
The Growing Green Guide (the guide) has been developed with advice from industry experts and knowledge from academic research,
to explain how to create high quality green roofs, walls and facades.
The development of the guide was supported by four inner Melbourne local governments through the Inner Melbourne Action Plan (the
cities of Melbourne, Port Phillip, Yarra and Stonnington) and by the State Government of Victoria, through the Victorian Adaptation and
Sustainability Partnership. The University of Melbourne is a project partner.
This guide is written for professionals who may be involved in the design, construction and maintenance of green roofs, walls and/or
facades. It is also relevant to developers, homeowners, and local and state governments.
The guide is targeted at projects based in Melbourne and Victoria, Australia, but is also largely relevant for a wider geographic area.
The Growing Green Guide is released under a Creative Commons licence to encourage periodic updates and use of the information in a
range of places.
Section 01
Explains what green roofs, walls and facades are, why they are important and the potential
benefits of these systems for Melbourne and Victoria. It also provides answers to some
frequently asked questions.
Section 02
Introduces some of the research that has been undertaken on green roofs, walls and facades to
provide a more specific understanding of their potential benefits.
Section 03
Was written in collaboration with industry experts to provide technical advice on the design,
construction and maintenance of green roofs, walls and facades.
Section 04
Highlights several existing green roofs, walls and facades in Melbourne and Victoria, as case
studies. Each example provides a description of the project, its design and components used,
maintenance, cost and results and reflections.
iii
Acknowledgements
The primary authors of this guide are Julie Francis (City
of Melbourne), Gail Hall (City of Melbourne), Sue Murphy
(University of Melbourne) and John Rayner (University of
Melbourne). Significant contributions were also provided from
the Guidelines Reference Group (see below) and support
was provided from the wider project team: Meg Jones (City of
Stonnington), Elissa McElroy (Inner Melbourne Action Plan), Kevin
Ayrey (City of Yarra), Lalitha Ramachandran and Nick Alsop (City
of Port Phillip) and staff from the Department of Environment
and Primary Industries.
This guide was put together with the assistance of a reference
group of experts on green roofs, walls and facades, including:
Nic Culnane, The Committee for Melbourne
Phil Edwards, Melbourne Water
Jock Gammon, Junglefy
Ken Hitchcock, KHD Landscape Engineering Solutions
Sam Innes, City of Port Phillip
Rafael Katigbak, Ronstan Tensile Architecture
Euan Laird, Nursery and Garden Industry of Victoria
Matthew Mackay, Hassell Pty Ltd
Carlo Missio, GHD Pty Ltd
Ben Nicholson, Groof Consulting
Clare Parry, Umow Lai
Merran Porjazoski, Bent Architecture
Warwick Savvas, ASPECT Studios
Nick Somes, Ecodynamics Pty Ltd
Erik van Zuilekom, Fytogreen
Scott Watson, VicRoads
Ralph Webster, Pad Creations
A final peer review was undertaken by Graeme Hopkins, Fifth

Creek Studio and Ed Snodgrass, Emory Knoll Farms (USA).
The project team is also grateful to the many other industry
experts, council staff and academics who provided advice on
drafts of this guide.
Research assistance was provided by RMIT students:
Amber Batley, Tim Coggan, Isobelle Cooke, Colin Dee, Thomas
Delbridge, Sally Hennessy, Kelly Hertzog, Raihana Rahmat and
Rhiannon Tomlin.
Assistance with compilation of the case studies was provided
by Guidelines Reference Group members along with David
McGlashan (Facilities Management Victoria), David Kutcher (The
Venny), Fiona Currie and Adel Calache (City of Boroondara),
Geoff Heard (Fytogreen), Peter Elliot (Peter Elliot Architecture),
Peter Heaney (RMIT), Stuart Nicoll (City of Melbourne), Annie
Hunter, Claire Farrell, Nick Williams, John Delpratt, Leanne
Hanrahan and Luke Flanagan (The University of Melbournes
Burnley campus).
The Growing Green Guide was designed by Universal Favourite
(www.universalfavourite.com.au)
SECTION
01
Image: Fytogreen
An introduction to
green roofs, walls
and facades
Image: ASPECT Studios
Green roof for apartment residents at Freshwater Place, Queensbridge Square, Southbank, Melbourne
introduction
Green roofs, walls and facades are becoming more common in cities across the
globe. Growing numbers of Australians are realising the potential of these living
systems to improve the quality of their built environment to provide social,
aesthetic, environmental and economic benefits.
Introduction
An introduction to green roofs, walls and facades
Like many other cities, Melbourne faces continued pressure

from increasing urbanisation. Rapid population growth and urban
development have transformed natural environments into areas
of highly engineered infrastructure. Heat generation from cars,
industry and commerce, coupled with the retention of the solar
energy by buildings and paved surfaces, creates unnaturally warm
city environments (known as urban heat islands). This can have
negative effects on human health and wellbeing. The transition from
the natural landscape to the built environment has also created
large areas of impervious paved surfaces, creating problems such
as loss of vegetation and habitat, increased surface run-off and
flash flooding. Each of these issues is being exacerbated by an
increasingly variable climate.
Collectively these issues present enormous environmental,
economic and social challenges and require new ways of thinking
to make our cities more liveable now, and into the future.
Green roofs, walls and facades are appealing as a way of adding

green infrastructure to a city because they can be included on new
buildings or retrofitted onto existing buildings, and require little, if
any, space at ground level. They are being used to compensate for
the loss of urban greenery, and to provide localised cooling and
aesthetic improvements in dense urban centres where there is
insufficient space for other types of green infrastructure.
It is estimated that there are more than 50 green walls, more than
100 green roofs and hundreds of green facades across Melbourne.
Yet there is limited Australian information about how to create and
manage these types of green infrastructure. This guide provides
technical advice on how to design, build and manage green roofs,
walls and facades so they can provide multiple benefits over a long
time span for building owners and the wider community.
Many cities around the world recognise the importance of having

green infrastructure; that is, natural landscape assets, including green
spaces and water systems. Green infrastructure includes trees, parks,
water sensitive urban design (such as wetlands and rain gardens)
and green roofs, walls and facades.
Figure 1. Pressure builds over our cities, with the transition from natural landscapes to hard
infrastructure, an increasingly variable climate and a growing population
Poor Water Quality

Urban run-off collects
pollution
High Energy Use

Air conditioners in offices,
industry & homes increase
greenhouse gas emissions
Poor Air Quality

Dust and vehicular pollution
& trapped air in urban canyons
Hotter Cities
Heat-related illness & death.
Poor city liveability
Less Green Space

Urban sprawl threatens food
production and reduces green space
for recreation and biodiversity
Flooding
Extreme rainfall and fewer
permeable spaces clogs drains
& leads to localised flooding
Introduction
Figure 2. Vegetation can be added to a building as green roof, green wall or green facade
Definitions
Green roof
A vegetated landscape built up from a series of layers that are
installed on a roof surface as loose laid or modular (that is, installed
layer by layer on the roof or as pre-prepared layers in trays).
Green roofs are constructed for multiple reasons - as spaces for
people to use, as architectural features, to add value to property
or to achieve particular environmental benefits (for example,
stormwater capture and retention, improved species diversity,
insulation of a building against heat gain or loss).
Vegetation on green roofs is planted in a growing substrate
(a specially designed soil substitution medium) that may range
in depth from 50 mm to more than a metre, depending on the
weight capacity of the buildings roof and the aims of the design.
Green roofs have traditionally been categorised as extensive
or intensive.
Extensive green roofs are lightweight with a shallow layer of
growing substrate of less than 200 mm deep, requiring minimal
maintenance. They generally have lower water requirements and
use small, low-growing plant species, particularly succulents (see
images 1 and 5 opposite). Ecoroofs or brown roofs are terms
used to describe these extensive green roofs. Roofs that are
designed and planted specifically to increase local plant diversity
and provide habitat (food and shelter) for wildlife are known as
biodiverse green roofs (see image 3 opposite).
Intensive green roofs are generally heavier, with a deeper layer
of growing substrate, and support a wider variety of plant types
(see image 2 opposite). Because they can support a heavier

weight, they are readily accessed by people. Intensive green roofs
need more irrigation and maintenance than extensive roofs, and
are highly engineered landscapes, often built directly on structures
with considerable weight load capacity, such as car parks. Roof
gardens or podium roofs are terms also used to describe these
types of green roofs. Roof garden is used particularly for sites
where less space is dedicated to the vegetation and growing
substrate and more to hard infrastructure such as decking (see
image 4 opposite).
Until quite recently, extensive green roofs were usually designed
as lightweight installations that were not publicly accessible,
while intensive green roofs were designed as amenity spaces for
people. The boundaries between these types of roofs are now
less distinct, and terms such as semi-intensive or semi-extensive
are used to describe roofs that show elements of these major
categories.
The International Green Roofs Association and other international
green roof industry organisations use these distinct roof classifications.
However, in this guide, green roofs are described in terms of their
particular characteristics, such as depth of growing substrate. The
authors of the guide consider that as each green roof is unique
and may incorporate a mix of design elements, strict classification
of types is no longer as helpful or relevant as it once was. Around
the world, designers and their clients, and those who install and
maintain green roofs, are exploring a range of creative solutions.
Introduction
1 Council House 2 in Melbourne has a non-irrigated, non-trafficable green roof comprised of modular trays
2 The demonstration green roof at The University of Melbourne, Burnley campus, is an accessible roof used by staff and students.
It demonstrates different irrigation regimes, growing substrates and plant species
3 A small-scale green roof at a public amenity block in Healesville, designed as an architectural feature and for biodiversity - it includes
indigenous species with the intent to create habitat. Image: Fytogreen
4 Lady Gowrie Child Care Centre, Docklands, is a roof garden designed for use and play. Image: City of Melbourne
5 The Venny, Kensington is a non accessible, light weight green roof with solar panels. Image: Andrew Wutke
Introduction
Green wall
A green wall is comprised of plants grown in supported vertical
systems that are generally attached to an internal or external wall,
although in some cases can be freestanding. Like many green roofs,
green walls incorporate vegetation, growing medium, irrigation
and drainage into a single system. Green walls differ from green
facades in that they incorporate multiple containerised plantings
to create the vegetation cover rather than being reliant on fewer
numbers of plants that climb and spread to provide cover. They
are also known as living walls, bio-walls or vertical gardens.
Green walls provide an attractive design feature, but also add to
building insulation by direct shading of the wall surface. They create
cooler microclimates and improve local air quality, and provide the
possibility of growing plants in locations that would not normally
support vegetation. A wide range of plants is used on green walls,
usually herbaceous, though some small shrubs can also be suitable.
The provision of adequate light is an important consideration,

particularly when planning an interior green wall, where artificial
lighting may be necessary (see image 1 below).
Many different proprietary green wall systems are available.
Some are hydroponic and others use a growing substrate. Green
wall structures vary from modular systems to sheet or boardbased structures with felt pockets to contain and support plant
life. All green walls require irrigation, often inclusive of fertiliser
(fertigation). Fertigation solution can be re-used, but requires
careful monitoring and management to ensure nutrients do not
build up over multiple recirculations to damaging levels.
A well-designed green wall system will fulfil both design and
functional aims by providing growing conditions suitable for the
selected species, have a long lifespan, require minimal component
replacement, and have achievable demands for maintenance.
1 Artificial lighting is an important element for this internal green wall in the foyer of Telstras Melbourne headquarters. Image: Fytogreen
2 Victorias Environmental Protection Authority has a green wall outside its head office in Carlton, signalling their interest in sustainability and a
visible cue to the buildings 6 star Green Star rating
3 Illura Apartments in West Melbourne have four green walls facing north-east, which helps to shade the wall surface in summer. Image: Fytogreen
4 The internal green wall is a design feature in the foyer of The Gauge, Docklands. Source: PAD Creations
Introduction
Green facade
A green facade is created by growing climbing plants up and across
the facade of a building, either from plants grown in garden beds
at its base, or by container planting installed at different levels
across the building (see image 4 below).
shading of the building, protection of its surface, and capture

of airborne particulate matter and volatile gaseous pollutants.
These benefits will be greater for evergreen species that retain
foliage cover year-round.
Climbing plants can attach directly to the surface of a building (see

images 3 and 5 below), or they can be supported on a structure
independent of the building (see images 1, 2, 4 and 6). The use
of climbers that anchor themselves to a structure by twining
stems or twining tendrils enables a green facade to be installed in
front of solid walls or some other structure, to create a partition,
privacy screen or sunshade. The degree of density of the facade
coverage can be managed to suit the required function. For
example, a facade designed to shade a building wall would ideally
have greater foliage density than a screen installed near a window
that is designed to allow at least partial views to the environment
beyond the facade.
For multi-level facades (see image 4 below), particularly at height,

wind can create significant problems for plant attachment. In these
settings, twining climbers are preferred over plants that adhere
directly to the building facade as the twining stems attach strongly
around vertical and horizontal supports. Foliage may still be stripped
under extreme wind conditions, so foliage type and size should be
matched to the level of exposure and likely wind strengths at the
site. In general, the higher the planting on a building, the more
extreme the growing conditions are likely to be. Other factors of
importance in multi-level facade design include planter box design
(volume, substrate, drainage), maintenance access and irrigation
system design.
Green facades are often installed because they provide an

attractive look to a building wall, or they may be used to block
out a view, or to provide shade for a building. Green facades can
create a cooler microclimate immediately adjacent to a building,
primarily through direct shading of the building facade, but also
from cooling from plant foliage (transpiration of water through the
leaves), and evaporative loss of water from the growing medium.
All climbing plants will provide some retention of stormwater,
The distinction between green walls and green facades is not

always clear. As the design and use of plants on vertical surfaces
expands, systems become harder to define. For instance, a hybrid
living wall system has been created in Adelaide that uses both green
wall and green facade technologies. This blurring of definitions is
akin to the already acknowledged difficulties in classifying green
roof types, where new designs merge what were previously
considered different categories.
1 A wire mesh structure supports this green facade at the RMIT University City campus 2 Green facades are used as a screen to cover a
bland wall on the green roof at Crown Casino, Southbank 3 This climbing plant attaches directly to the facade of Victoria Barracks, St Kilda
Road, Melbourne 4 Twining plants are used to create a multi-level green facade at Council House 2 in Melbourne. Planter boxes located on
each balcony allow the facade to extend to the full height of the building 5 Deciduous climbing species provide an attractive feature in autumn
at the University of Melbournes Burnley campus 6 A climbing plant (with a scrambling habit) is used on this free-standing green facade in
Brisbane, Queensland
Introduction
Benefits of green roofs, walls & facades

There is a range of benefits, outlined below, that can potentially
be provided by green roofs, walls and facades. Some provide
benefits to the public at large and some only benefit the building
owner or occupants. It is important to recognise that the following
benefits are only realised if the roof, wall or facade is planned and
constructed well and has the supporting management required

to sustain it. Section 3 of this guide discusses the importance of
design in realising the intended outcomes from any project.
Section 2 provides the research evidence for these benefits.
Increased property value and other benefits for

building owners
Building owners and developers are increasingly installing green roofs, walls or facades to add a
point of difference, increase commercial returns, provide visual appeal and turn a building into a
local landmark. Most building owners in Melbourne ignore the potential of large, leasable spaces
on rooftops that can be transformed into versatile recreation, amenity or productive facilities, or
commercial spaces for bars, restaurants or cafs.
While the construction of a green roof, wall or facade can be independent from the rest of
a building project, involving specialists early in the construction timeline will help to minimise
risks associated with design development. Importantly, early design discussions will help ensure
that the roof, wall or facade can be planned and incorporated in other building aspects such as
drainage, irrigation, lighting and weight loading.
Green roofs can lengthen the lifespan of a traditional roof surface. They protect a roof s
waterproof membrane from solar radiation and add insulating materials (vegetation, substrate
and other layers) to reduce severe temperature fluctuations on the roof surface.
Stormwater management
Green roofs absorb and retain rainwater and can be used to manage stormwater run-off in
urban environments. They can also filter particulates and pollutants. Stormwater run-off can be
reduced or slowed because it is stored in the substrate, used by or stored in the foliage, stems
and roots of plants, and also evaporates directly from the substrate. Additional water storage
capacity in green roof systems can be provided through incorporation of a water retentive layer
or drainage layer at the base of the green roof.
Several factors influence the extent to which a green roof can reduce the volume of water runoff into the stormwater system, including depth and properties of the growing substrate, type
of drainage layer used and roof slope. Plants and drainage systems are important considerations
in the design of a green roof for stormwater management. Details on research supporting
stormwater management are provided in Section 2.
Introduction
Improved thermal performance

A significant benefit of green roofs, walls and facades is the potential for reducing building
heating and cooling requirements. Green walls and facades can reduce heat gain in summer
by directly shading the building surface. Green roofs reduce heat transfer through the roof and
ambient temperatures on the roof surface, improving the performance of heating, ventilation
and air conditioning (HVAC) systems. While there is great potential to cool buildings, research
data and the results of modelling studies vary greatly in relation to the extent of the difference
in temperature and the energy savings that are predicted for buildings with green roofs versus
conventional roofs (see Section 2).
Cooling a city urban heat island effect

Hard surfaces in urban environments, such as concrete, brick, glass, asphalt and roofing, have a
high thermal mass, collecting the suns heat during the day and re-radiating it slowly back into
the atmosphere. This contributes to a rise in ambient temperature in cities, creating large, stable
masses of hot air (urban heat islands), especially during periods of calm, still weather.
Temperatures can be reduced by covering a roof or wall with a layer of vegetation that shades
building materials which would otherwise absorb heat. Evapotranspiration provides cooling effects,
as water is evaporated from the soil and plants and plants transpire by taking water in through
roots and releasing it through leaves. Energy from the sun that would otherwise heat the roof
or wall surface and increase ambient air temperatures is instead used in the evapotranspiration
process, resulting in latent heat loss that lowers surrounding air temperatures. When green wall
and facade plants are grown on a support system that leaves a gap between the wall and the
planting, hot air moves up by convection through the space between the wall and the vegetation,
providing passive cooling.
A city-wide strategy to implement green roofs, walls and facades could help mitigate some
of the negative consequences of urban heat islands, and consideration should be given to
appropriate plant selection and substrate depth to maximise cooling potential.
Creation & preservation of habitat & ecological biodiversity

Green roofs can contribute to and enhance biodiversity by providing new urban habitats and
specific habitats for rare or important species of plants or animals. Green roofs can also provide
a link or corridor across urban ecological deserts and assist in migration of invertebrates and birds.
Designing for biodiversity requires consideration early in concept development with regard to
plant species, food sources, habitat values, access points and building heights.
10
Introduction
Aesthetics, open space and urban food production

The liveability of cities is increasingly dependent on the availability of and access to green open
space. Green roofs, walls and facades can increase amenity and provide opportunities for food
production, recreation, relaxation or commercial ventures.
In dense, rapidly growing urban areas, the contribution of green roofs, walls and facades to overall
green space should not be underestimated. In inner-city areas especially, most space is occupied
by buildings and related infrastructure and the opportunities for new parks and gardens is extremely
limited. Green roofs, walls and facades can be used for multi-level greenery designs that connect
with ground level green spaces.
Cleaning the air

Green roofs, walls and facades can contribute to the removal of gaseous pollutants from the air,
although their effectiveness varies with plant species and area of cover. Plants with a high foliage
density or with textured leaf surfaces that trap small particles also assist in removing particulate
pollution, through dry deposition on the foliage or through rain wash. On a larger scale, green
roofs, walls and facades can help to reduce overall environmental heat gain (re-radiation of heat
from building materials with high thermal mass), in turn improving air quality as less photochemical
pollutants are produced at lower air temperatures.
In interior environments, plants have been shown to have a significant capacity to reduce volatile
organic compounds from the air. Carpets and other soft furnishings and office equipment are
common sources of these gaseous pollutants; inclusion of vegetation, such as a green wall, can
help to improve the air quality of the indoor environment.
Next Steps
Read the frequently asked questions and the rest of the guide to understand the details of green roof, wall or facade systems,
or seek advice from a professional in the industry to learn more about approaches that may be suitable to achieve particular
identified aims for your site.
Section 2 details some evidence of the benefits of green roofs, walls and facades. In Section 3, technical advice is provided
on how to design, construct and maintain green roofs, walls and facades. Finally, Section 4 provides detailed case studies of a
selection of Victorian green roof, wall and facade projects to give practical examples of design, construction and maintenance.
11
FAQ
Introduction
FREQUENTLY ASKED QUESTIONS

Do green roofs work on
new and old buildings?
Can I have a green roof on

a slope?
How much do green roofs,

walls and facades cost?
Yes. Green roofs can be fitted to a range

of roof types. A new building can be
constructed to accommodate the weight
loading necessary for a green roof. Some
existing buildings will have the capacity
to support a green roof, or additional
structural support can be retrofitted to
support the required increase in loading.
A structural engineer must be engaged
to clarify details of building structure and
weight loading capacity.
Yes, but steeper slopes present a challenge,

and require specialised design solutions,
including drainage boards and systems to
help hold substrates and plants in place.
Costs will vary significantly between sites

and projects. The case studies in this guide
indicate costs for a range of projects of
varying complexity for comparative purposes.
The key factors that influence costs are the
size of the roof, wall or facade; the design
and type of materials used in the roof (for
example, structural reinforcement, volume
of growing substrate and components used
in the mix, plants, system components, hard
surfaces and furniture, etc.); requirements
for access; and the requirements for ongoing
maintenance (including inputs for irrigation,
weeding, pruning, fertiliser).
Can I green any building?

Most building surfaces have the potential
for greening. Challenging sites such as
those in deep shade or with low weightloading capacity, and tall buildings or sites
with limited access, require specialist
engineering, design and technical input.
Can a tile roof be greened?

Yes, but it requires design expertise and
specialised systems that are not yet widely
available in Australia.
Is irrigation necessary for a

green roof, wall or facade?
All green walls and most green facades
and roofs, require irrigation. It is possible to
install a green roof with no irrigation, but
this will limit the range of plants that can be
used successfully and the potential benefits
of the roof (such as summer cooling or
aesthetically pleasing views of leafy plants).
Some green facades grown in garden bed
settings may not need irrigation.
How much water do

you need?
There is no one answer, as calculating
the water needed to sustain a green roof,
wall or facade depends on climate and
environmental influences, the design and
type of system used, and on the substrate
and vegetation characteristics. Explore
alternative sources of water for use in
irrigation, such as harvested and recycled
water, to minimise reliance on potable
water. Many green walls rely heavily on
irrigation and it is essential to establish
that supply can meet demand.
Will plants overtake the

roof or wall?
Vegetation maintenance on a green roof
is important and should be factored in
during the design phase of the project.
Selection of less vigorous plants (species
with low biomass) or those that do not
seed freely will help reduce maintenance
requirements. Green walls can be designed
to have an air gap between the back of the
system and the wall, to provide air pruning
of roots. Green facades will require pruning
to manage size and maintain effective cover.
Green wall technologies offer notable

variation in costs, with relatively cheap
domestic green wall products suited to
small-scale DIY (do-it-yourself) applications,
through to large and small-scale customdesigned commercial systems. Each presents
a different level of refinement and security
for long-term success.
Will the green roof leak

and cause problems?
Any roof has the potential to leak.
Well-constructed green roofs, walls
and facades will not leak or cause other
structural damage to the building. Correct
installation of waterproofing is essential on
roofs and some walls, and leak detection
systems can minimise risks on green roofs.
Waterproofing membranes can actually
last much longer under green roofs because
they are protected from damage by the
elements by overlying layers.
12
FAQ
Introduction
FREQUENTLY ASKED QUESTIONS

What is the typical lifespan
of a green roof, wall or
facade?
How much pruning will be

needed if I grow a green
facade?
Are green roofs, walls and

facades environmentally
sustainable?
The lifespan is directly related to the

quality of the design, construction and
maintenance, and in particular, the
longevity of the system components.
Some green roofs in Europe have been
in place for more than 75 years and are
still performing strongly. There are many
examples of direct faade greening in
Melbourne that have lasted for decades.
The projected lifespan of green wall and
facade technologies that are more recent
entries into the market are less well
understood.
Pruning is usually required once or twice

a year, although this will depend on the
vigour of the plant species and the growing
conditions. Annual pruning is important to
control growth and keep vegetation away
from building fixtures (lighting, heating or
cooling equipment, drains).
Design of the system is paramount to how

well it contributes to broad sustainability
goals, such as pollutant filtration, thermal
insulation, providing habitat or localised
cooling. By considering how you design,
operate and maintain your system you can
also ensure that the materials and practices
used are environmentally sustainable now,
and in the long term. This process is called
life-cycle analysis. Recycled waste products
could be used (from the building materials
to substrate materials) or local products
sourced rather than imported materials
to reduce the energy used in these
components. Some systems may require
more water than others, but if that water
is sourced from harvested stormwater or
recycled water, it may be more sustainable
than a low water-using system that uses
potable water. Considered application of
fertiliser is required to ensure there is no
negative effect from polluted run-off from
the site. Management of weeds and pests
in the vegetation through a maintenance
regime will also contribute to overall
sustainability outcomes.
Will construction of
a green roof, wall or
facade cause delays in
the construction of my
building?
Although a green roof, wall or facade
should be considered an integral
component of a building, its construction
can usually be done independently from
the rest of the build, so it poses little risk
in causing delays. It is very important
to include the installation specialists in
early design discussions and associated
construction project timelines to establish
the most efficient construction timetable
and ensure that drainage, irrigation and
lighting are designed to include the green
roof, wall or facade.
Can I have solar panels on

a green roof?
Yes. There are examples of green roofs in
Melbourne and other parts of the world
where green roofs have solar panels
installed above them.
Could I just paint my roof

white to achieve summer
cooling?
Increasing roof reflectance through a white
roof is one way of reducing heat gain
through the roof. However, a white roof
will not capture and retain stormwater,
provide aesthetic benefits or increase
biodiversity values. Paint eventually
degrades and requires maintenance.
Most white roofs cannot help insulate
the building in the winter months and
will therefore only improve the buildings
energy efficiency in the heat but not the
cold. A green roof can help a buildings
energy efficiency year round.
How do I know if my
building has the capacity
for a green roof?
An architect, engineer and green roof
provider are needed to ascertain that
a green roof can be installed on a new
building. To retrofit a green roof on an older
building, consultation with an architect
and/or structural engineer is necessary to
determine the load-bearing capacity of the
structure. Consult with green roof, wall or
facade providers to discuss design ideas
and solutions for the site.
SECTION
02
Evidence-based
benefits of green
roofs, walls and
facades
14
Evidence-based benefits of green roofs, walls and facades
Evidence
The following section examines the benefits of green roofs, walls

and facades that have been established by research. In most
cases, experimental testing and/or computer modelling based on
experimental data are used. In this overview, green roofs receive the
most coverage because more research has been undertaken about
them and firm conclusions can be drawn. Research into the most
effective uses of green walls and facades is underway in many parts
of the world.
The information provided is from peer-reviewed scientific,
architectural and engineering research journals, technical reports
and books. References and links are provided to the original
articles, although some of these are accessible only through journal
subscriptions. Data used here have been summarised or re-plotted to
demonstrate key points.
15
Evidence
Reducing the energy budget of a building

Green roofs, walls and facades can reduce cooling and heating
costs, by reducing heat gain or loss across the building surface.
Figure 3 shows the results of a study at Kobe University, Japan,
where a green roof performed best out of four different roof
treatments in reducing heat flux from the outside to the inside
of the building. The roofs differed in albedo (the ability to reflect,
rather than absorb, solar energy). A high albedo value means that
more light is reflected and less is absorbed. A green roof planted
with lawn grass had the lowest albedo, but was most effective at
reducing heat flux into the building. Heat flux across the cool roof
treatment using reflective white paint was 10 times higher than for
the green roof, although its albedo was almost five times greater.
The sensible heat flux across the white roof surface is small
because most solar radiation is reflected, and little is absorbed.
Sensible heat flux across the green roof is small because of loss
of latent heat through evaporation of water from plants and the
growing substrate, even though the amount of solar radiation
absorbed is high. Grey paint and concrete have similar reflectance,
but heat flux with alternative cool roof paint (reflective grey) was
greater than the bare concrete roof alone.
Figure 3. Sensible heat flux under different roof treatments and albedo (ability to reflect solar radiation)
Average sensible heat ux (W/m2)
100
90
80
70
60
50
40
30
20
10
0
Albedo
,-.-/01- 23-4 5a7n9
:;<n/3-9-
,-.-/01- w>79- 5a7n9
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Lawn
Source: Takebayashi H, Moriyama M (2007) Surface

heat budget on green roof and high reflection roof
for mitigation of urban heat island, Building and
Environment 42: 2971-2979.
-./.012. 34.5 paint
;<=n04.t.
-./.012. w?it.
paint
A green roof provides significant cooling benefits compared to

an uninsulated bare roof, although the most effective cooling
comes from inclusion of insulation under the roof. Modelling
comparisons suggest that green roofs could be useful on poorly
insulated buildings to reduce the thermal conductance across
the roof deck. Thermal conductance (U-value) is the inverse of
Lawn
the resistance to transfer of heat (R-value). A study conducted

in Athens, Greece, modelled the effect of adding a green roof to
concrete roofs of different construction. Figure 4 shows that a
green roof lowers heat transfer across a 25 cm thick and a 10 cm
thick uninsulated concrete roof.
16
Evidence
Figure 4. Effect of a green roof on heat transfer (thermal conductance) modelled for different types of
roof construction
20
bare roof
18
with green roof
Thermal conductance
(U-value; W/m2K)
16
14
12
10
25 cm concrete
8
>10 cm concrete roof deck sandwich with 10 cm

ins9:a;on :a<er
6
4
2
0
cm concrete
concrete
2525 cm
roof deck
10 cm concrete
roof deck
Insulation of a building translates into energy savings for both

heating and cooling. In Melbourne, with a well insulated building,
winter heating is likely to dominate total energy costs, although
this will depend on heating and cooling set points preferred by
the buildings occupants. The R-value of an insulation material is
a measure of its resistance to transfer of heat. Establishing the
R-value offered by a green roof, wall or facade depends on a
complex interaction of all the materials used, the depth of the
growing substrate and the amount of water held in the substrate,
as well as the plant selection, degree of coverage by plants and
whether that coverage is present year-round. The following studies
investigated the effect of green roofs compared to bare roofs on
the thermal performance of buildings.
Source: Niachou A,
Papakonstantinou
K, Santamouris M,
Tsangrassoulis
A,
bare roof
Mihalakakou G, (2001)
with green roof
Analysis of the green roof
thermal properties and
investigation of its energy
performance, Energy and
Buildings 33: 719-729.
>10 cm concrete
eck sandwich with 10 cm
10roof
cmdconcrete
:a<er
roofins9:a;on
deck with
10 cm
insulation layer
A study carried out in Singapore, comparing the effect of different

vegetation types on a green roof with 40 cm deep soil, showed
that heat gain was prevented, and heat loss was greatest under
vegetation with the largest and densest foliage cover (Raphis
palm used as a shrub) see Figure 5. The bare hard roof surface
accumulated and retained the most heat. Turf, and trees with an
open canopy, provided less cooling benefit, with similar heat loss
to that of bare soil. The reduction of heat gain and increased heat
loss from soil, compared to the hard roof surface, is most likely
due to evaporation of water held in the soil.
Figure 5. A comparison of thermal effects on a green roof under different types of vegetation cover
Total heat gain or loss (kJ/m2/

vday)
400
Total heat gain
350
Total heat loss
300
250
200
150
Source: Wong NH, Chen Y, Ong CL, Sia A, Investigation

of thermal benefits of rooftop garden in the tropical
environment, Building and Environment 38 (2003)
261-270.
100
50
0
bare
hard
bare
hard
surface bare soil
surface
turf
tree
tree
shrub
17
Evidence
Figure 6 shows the results of a study on energy demand under

a green roof and bare roof in Melbourne. The building was
described as having double brick external walls, a concrete slab
floor and concrete roofs - no mention was made of ceiling
insulation. Temperature measurements were made between
September 2008 and July 2009, in a room with a conventional
waterproofed concrete bare roof, and a room with a green roof
installed over the roof deck. These measurements were used in a
simulation to predict the effect of a green roof on annual energy
costs. Parameters used in the model included cooling and heating
set points of 24C and 18C respectively, and an assumption that

the space was heated or cooled between 8 am and 6 pm. Results
showed that cooling and heating costs for the room covered
with a vegetated roof would be 50 per cent and 12 per cent
lower respectively than for the same room with a conventional
bare concrete roof. For a building constructed from less strongly
insulating materials, although winter heating and summer cooling
requirements would be higher, the green roof would achieve
comparable energy savings.
Figure 6. Heating and cooling energy demand in a room under a bare roof and a green roof
Heating Energy
Cooling Energy
Cooling Energy
5000
1000
4000
800
3000
Axis Title
Annual Energy Demand (MJ)
3ea4ng Energy
2000
1000
600 roof
Test room + bare
Room under bar
Test room + green roof
Room under gre
400
200
room under room under

bare roof
green roof
room under room under

bare roof
green roof
Source: Chen and Williams (2009) Green roofs as an adaptation to climate change: modelling the green roof at the Burnley campus,
The University of Melbourne, Research Report for CSIRO Climate Adaptation Flagship.
One of the major benefits of the insulation provided by a green

roof is the reduction of internal and external heat fluctuations. The
stability of internal temperatures under a green roof is increased
and contributes to thermal comfort year-round by preventing
heat gain from the outside to inside in summer, and by reducing
heat loss from inside to outside in winter. The construction of the
roof deck and other building components plays a major role in
determining the extent of heat gain or loss from a building.
Figure 7 shows the results of a study in Brazil that compared
external roof temperatures with internal ceiling temperatures
in a building with rooms covered by a green roof, metal roof or
a ceramic tile roof. Measurements were made over a week in

both warm and cold seasons. Heat flux was recorded between
the three roof types and the internal surface of the ceiling inside
each room, and internal air temperature was measured 1.5 m
above the floor in the three rooms. The green roof was planted
with a monoculture of a low-growing succulent herb (Bulbine
frutescens) in a substrate 140 mm deep. The graph indicates that
the room under the green roof showed the smallest variation in
daily temperature during the day in the cold season: this was also
the case during the warm season, with a maximum daily variation
of 1.2C.
18
Evidence
Internal room
Internal room temperature
(C) temperature (C)
30
25
Figure 7. Internal temperature effects of different roof types
20
30
15
Under metal roof

Under 8led roof
25
10
Under green roof
20
5
Under metal roof
15
0
10
Under 8led roof
Cold season day
Cold season night 4a5 daily 6aria8on
Cold season day
Cold season night 4a5 daily 6aria8on
5
0
Green roof trials in Adelaide (June 2011-May 2012) compared

two plots with 300 mm deep growing substrate to four plots
with shallower, 125 mm thick substrate. Two of the shallow
depth plots had a trafficable aluminium grating installed 150 mm
above the surface of substrate to create an air gap (see image).
The aluminium grating treatment was tested to investigate the
effect of shading of the vegetation. The substrates used were
either a lightweight growing medium or a heavier substrate made
from recycled brick and other inorganic materials. Temperature
fluctuations of the underlying surface were smaller for the
inorganic growing substrate with its higher thermal mass, than for
Under
green roof
Source:
Parizotto
S & Lamberts R (2011) Investigation of
green roof thermal performance in a temperate climate:
a case study of an experimental building in Florianpolis
city, Southern Brazil, Energy and Buildings 43:1712-1722.
the lightweight growing substrate. The variation in temperature

across the entire day was halved with the aluminium grating
installed over the substrate and vegetation. The grating created an
increased insulation effect with a combination of shading, and from
the creation of an unstirred air layer.
Source: Clay R, Wild N, Hopkins G, Goodwin C (2012) Determining
and understanding thermal characteristics of green roofs in the City of
Adelaide, Appendix 1 of Green Roof Trials Monitoring Report by Fifth
Creek Studio for SA Governments Building Innovation Fund and Aspen
Development Fund No. 1.
Experimental green roof on ANZ House, Adelaide, with trafficable aluminium grating 150 mm above the substrate
19
Experimental studies on green walls and facades focus on the

shading (and cooling) benefits that facade greening provides. Even
though a broad range of factors influence how much shading a
green facade offers (including the presence and type of a support
structure, facade orientation and whether the climber is deciduo
us or evergreen), decreases in wall surface temperature of between
5C and 10C are common. The most useful assessments come
from data collected throughout the year: in the future, longitudinal
studies could provide additional value because outcomes are likely
to change as the facade matures. To date, there is limited published
data on thermal benefits from vertical greening in Australian
conditions.
Evidence
Table 1 shows the results of a Spanish study on green facades.

Temperature measurements were made over a year on the
north-east, south-east and south-west sides of a building in
Golms, Spain, that was covered with the deciduous climber
Wisteria sinensis (Chinese Wisteria). The climber was grown on a
steel mesh support system. Shading of the south-west face of the
building provided the greatest cooling effect.
Table 1. Effect of a green facade on building thermal performance
Parameter measured
Difference in temperature in front of and

behind the facade
Difference in surface temperature

between bare wall and vegetated wall
(summer)
Difference in relative humidity in front of

and behind the facade
Outcome
Effect of the green facade
1.4C cooler in summer
Absorption of light and heat energy by

foliage keeps the cavity temperature
lower.
3.8C warmer in winter
Average bare wall temperature is

5.5C higher
Maximum temperature is 15.2C higher
7% higher in summer
8% lower in winter
Facade support system creates a

microclimate/unstirred air layer next to
the wall even when stems are bare.
Full leaf cover provides effective shading
and prevents heat gain by the building
Evapotranspiration from leaves causes a
local increase in humidity (and cooling)
in summer which is not apparent when
stems are bare
Source: Prez G, Rincn L, Vila A, Gonzlez JM, Cabeza LF (2011) Behaviour of green facades in Mediterranean Continental climate, Energy
Conversion and Management 52:18611867.
Research undertaken in Adelaide investigated hybrid vertical

greening systems that combine elements of green facades and
living walls. Air temperature and solar radiation were measured
in front of and behind the green facade. Although there was little
reduction in air temperature in front of the green facade (relative
to the air temperature in front of the adjacent bare brick wall), the
wall surface temperature was considerably lower. The green facade
wall surface temperature was 37 to 38C, whereas the brick wall
was 45.8C .
Source: Hopkins G, Goodwin C, Milutinovic M, Andrew M (2012)

Post-construction monitoring report: Living wall system for multi-storey
buildings in the Adelaide climate. Prepared for the Government of
South Australia.
20
Evidence
Contribution to urban cooling

Concrete, bricks, glass and large areas of impervious paved
footpaths and roads contribute to heat gain in urban areas. This,
and the loss of shading and cooling from vegetation in high density
urban development, contributes to the formation of urban heat
islands: increased ambient temperatures that arise when warm
stable air masses develop above cities, particularly during periods
of calm weather and low wind speeds.
A modelling study conducted by CSIRO and the Nursery and
Garden Industry of Australia investigated the likely effect of increasing
vegetation cover in Melbournes Central Business District (CBD)
on average summer daily maximum (ASDM) temperatures over
the period of December through February. Remote sensing
imagery from the 2009 summer was analysed, and showed that
daytime land surface temperatures were significantly reduced by
vegetation. An urban climate model was then used to predict urban
temperature changes under different vegetation schemes for the
2009 climate, and for projected future climates in 2050 and 2090.
Comparisons were made using the CBD both in its present form as a
reference (with respect to urban boundary and density of vegetation),
and with increased densities of vegetation. Vegetation density was
doubled at ground level, installed on green roofs, or both.
Green roof vegetation was 0.5 m high and covered 50 per cent
of building rooftops completely. In all models, it was assumed that
vegetation was irrigated, so that evapotranspiration rates did not
vary significantly between different years. In the 2009 scenario,
ASDM temperatures were reduced by 0.3C by doubling the
density of vegetation in the CBD, or by 0.4C with green roofs.
Increasing vegetation density both at ground level and with green
roofs reduced ASDM temperatures by 0.7C. In comparison, the
creation of large urban parklands reduced ASDM temperatures by
2C. (Suburban areas were 0.5 to 0.7C cooler than the CBD.)
The same relative effect of vegetation on ASDM temperatures
was predicted for 2050 and 2090. Green roofs, in conjunction
with cooling from an increased density of street trees and
park vegetation at ground level, could help to decrease urban
temperatures, reduce summer heat stress and the peak electricity
requirements for air conditioning.
Source: Chen D, Wang X, Khoo YB, Thatcher M, Lin BB, Ren Z, Wang
C-H, Barnett G (2013) Assessment of Urban Heat Island and
Mitigation by Urban Green Coverage, in Mitigating climate change:
the emerging face of modern cities, Khare A, Beckman T (eds),
Springer, Berlin, New York.
An Australian report outlines principles for choosing the green

roofs, walls, facades, and other more traditional uses of vegetation
to cool urban areas (collectively known as green infrastructure)
for cooling of urban spaces in the Greater Melbourne area. The
report is available at http://www.vcccar.org.au/publications
Source: Coutts A, Livesley S, Norton B, and Williams N (2013)
Urban Heat Island Report: Decision principles for the selection and
placement of Green Infrastructure, Victorian Centre for Climate
Change Adaptation Research.
A 2005 study in Toronto, Canada modelled the effect of
implementing green roofs on low-rise buildings with low slope and
flat roofs of areas greater than 350 m2, and concluded that green
roofs, implemented as a city-wide strategy, could mitigate the heat
island effect by reducing local ambient temperatures by 0.5 to
2C. It was calculated that this could save Toronto homeowners
and businesses CAN$21 million annually by reducing the energy
demand for mechanical cooling.
Source: Banting, D., Doshi, H., Li, J. & Missios, P. 2005, Report on the
environmental benefits and costs of green roof technology for the
City of Toronto, Prepared for City of Toronto and Ontario Centres of
Excellence Earth and Environmental Technologies, Ryerson University,
<http://www.toronto.ca/greenroofs/pdf/executivesummary.pdf>
21
Evidence
Managing stormwater volume

Green roofs absorb and retain water and can be an effective
strategy for reducing stormwater run-off in urban environments.
When rain falls on a bare roof, run-off water flows into drains
very rapidly. The rate of run-off depends on the slope of the roof
as well as the volume of the rain event. When the rain stops, runoff continues until the roof is drained: any water remaining on
the surface will evaporate. On a green roof, plants and growing
substrate intercept rainfall. Some water will evaporate directly off
plant foliage, but rain that falls directly onto the substrate, or drips
off the foliage, percolates downwards. Some water is absorbed
by substrate particles, and some drains down into underlying

layers where it can be stored if these have the capacity to hold
it (typically the drainage and protection/water retention layers).
Excess water drains onto the roof and out into the stormwater
system. So, on a green roof, both the time to onset and the time
to peak flow of stormwater entry are delayed, and the overall
time taken to drain the roof is increased, as shown in Figure 8. The
overall volume of stormwater is reduced because of the retention
by the substrate and other layers of the green roof.
Figure 8. Theoretical graph comparing stormwater run-off from a bare roof and green roof
The advantage of using vegetation to manage stormwater run-off

is that it increases the surface area available for rainfall capture,
and thus helps slow the rate of entry and reduce the volume of
stormwater. The height and spread of vegetation, as well as the
type and diversity of species used affects how much rainfall plants
can capture on their leaves, and how much water they release
back into the environment through transpiration. Evaporation
of water from the substrate also reduces the overall volume of
stormwater.
Figure 9 shows data from an experimental green roof study in

Michigan, USA, where rainfall retention was measured over 14
months. The three treatments were: a roof with gravel ballast only;
an unplanted green roof; and a green roof planted with succulents
(Sedum species). All roofs had a 2 per cent slope. Run-off was
measured for rain events of different intensity. The green roof with
plants retained the highest proportion of water from heavy rain
events. For smaller rainfall volumes, the substrate-only roof was as
effective as the green roof in retaining water. Both captured more
water than the ballasted roof.
22
Evidence
Figure 9. Rainfall retention under three roof treatments for rain events of different intensity
100
Retained rainfall (as % of total)
90
80
70
60
50
Source: Van Woert ND, Rowe DB,

Andresen JA, Rugh CL, Fernandez RT,
Xiao L (2005) Green roof stormwater
retention: effects of roof surface,
slope and media depth, Journal of
Environmental Quality 34:1036-1044.
40
30
20
10
0
Light (<2 mm)
Heavy (>6 mm)
Medium (2-6mm)
Type of rain event (volume in mm)
Roof surface with 2 cm gravel ballast

Extensive green roof without plants in 2.5 cm substrate
Extensive green roof with plants in 2.5 cm substrate
Figure 10 shows the results of an analysis of published data on

rainfall retention across a range of roof types. Data were analysed
for five (5) bare roofs, eight (8) roofs covered with gravel ballast,
121 shallow (extensive) green roofs and 11 deeper substrate
(intensive) green roofs, with average substrate depths of 0 mm,
50 mm, 100 mm and 210 mm respectively. Deeper substrate green

roofs retained the most rainfall on average, with minimum and
maximum retention of 65 per cent and 85 per cent respectively: for
roofs with shallower substrates it was 27 per cent and 81 per cent.
Figure 10. Rainfall retained by different types of green roofs
Retained rainfall (as % of total)
100
90
80
70
60
50
40
30
20
10
0
Bare
roofs
Bare
roofs
Ballasted
roofs
Extensive
Extensive
green roofs
green roofs
Intensive
green roofs
Source: Mentens J, Raes D, Hermy R

(2006) Green roofs as a tool for solving
the rainwater runoff problem in the
urbanised 21st century? Landscape
and Urban Planning 77:217-226.
Note: When considering international research results, keep in mind climate differences to Australia.
Many European and North American green roofs have very shallow substrates, such as the 2.5 cm deep
substrates described in Figure 9. In Melbourne conditions, a minimum depth of 10 cm is recommended for
a green roof substrate. Shallower substrates are likely to dry out too quickly, and plants will not survive.
23
Figure 11 shows how slope affects stormwater retention. Green

roofs with 2 per cent and 6.5 per cent slopes were planted with
succulents (Sedum species) in 4 cm deep growing substrate. Runoff was measured for rain events of different intensity.
Evidence
The difference in percentage run-off between the two slopes was

greatest in heavy rain events, with the highest run-off observed
from the more steeply sloped roof.
Figure 11. Rainfall retention on green roofs with different slopes

100
Retained rainfall (as% of total)
90
80
70
60
50
Source: Van Woert ND, Rowe DB, Andresen JA,

Rugh CL, Fernandez RT, Xiao L (2005) Green roof
stormwater retention: effects of roof surface, slope
and media depth, Journal of Environmental Quality
34:1036-1044.
40
30
20
10
0
Medium (2-6mm)
Light (<2 mm)
Type of rain event (volume in mm)
2% slope
Heavy (>6 mm)
6.5% slope
A green roof captures a higher percentage of rainfall of a light rain

event than a heavy one. If the rain event is very small, there may
not be any run-off from the green roof, especially if the substrate
is dry. During intense rain events where a large volume of water
is delivered in a short time, the substrate may not absorb all the
rain that falls, even on a densely vegetated roof. In these situations,
the vertical movement of water through the substrate dominates,
although vegetated roofs usually still have lower run-off than
bare roofs. The run-off from intense or long rain events could be
harvested and stored for irrigation.
Figure 12 shows how retention varies with different intensities of

rainfall. Rainfall run-off was collected from a bare roof and a green
roof with low growing herbaceous and succulent species planted
in a growing substrate 10 cm deep. The green roof captures most
of the volume of a small rain event. Although the green roof did
not capture much of the rainfall from a more intense rain event,
it did capture more than the bare roof.
Figure 12. Rainfall retention on green roof with different rainfall
Retained rainfall (as% of total)
100
90
80
70
60
50
Bare roof
40
Green roof
30
20
10
0
2.4 mm rain event in 55 min 512.1 mm rain event in 145 min
Source: Teemusk A, Mander (2007) Rainwater

runoff quantity and quality performance from
a green roof: the effects of short-term events,
Ecological Engineering 30:271-277.
24
Evidence
Research examining four different green roofs in Auckland

investigated rainfall retention in relation to substrate depth and
composition. Peak flow per rainfall event from the green roofs was
62 per cent to 90 per cent less than run-off from a corresponding
conventional roof. During winter, when plants are not actively
using water from the substrate in transpiration, rainfall retention
was reduced. It was found that water retention and peak flow
are affected by the type of drainage layer used, and the horizontal
distance that stormwater has to travel before it enters the
perimeter gutter or point drains that lead off the roof. Increasing
the distance to the drains, or using drainage layers that have some
storage capacity (either granular aggregate or plastic cells with
water holding capacity), should increase the retention period on
the roof.
Source: Fassmand-Beck E, Voyde E, Simcock R, Hong YS (2013) 4

Living roofs in 3 locations: Does configuration affect runoff mitigation?
Journal of Hydrology 490:11-20. See also Fassman-Beck EA and
Simcock R (2013) Living Roof Review and Design Recommendations
for Stormwater Management, prepared by Auckland UniServices for
Auckland Council, Auckland Council Technical Report 2013/045.
Improving stormwater quality

In urban environments stormwater collected from surfaces at
ground level is usually contaminated. Rainfall run-off carries a mix
of litter, organic materials (plant material and animal droppings),
dust and soil particles and chemical pollutants such as oils and
fertilisers. In contrast, the quality of water arriving at stormwater
drains from roofs is relatively high.
Data from two separate experiments (Tables 2 and 3) show the
improvement of the quality of run-off from green roofs relative to
bare roofs. The higher concentration of nitrogen and phosphorus
Table 2. Comparison of nitrogen (N) and

phosphorus (P) content in rainwater and run-off
from bare roofs and green roofs (modular boxes)
in run-off from the bare roof is most likely due to the wash
down of contaminants in the first flush run-off after rain begins.
The greater surface area for potential capture and storage of
these contaminants on a green roof (on foliage, in the substrate)
reduces the nutrient loading entering stormwater run-off. In Table
2, the green roof included mixed herbaceous perennials, including
succulents, planted into 10.2 cm deep substrate held in modular
boxes that were installed on a roof. In Table 3, succulent species
were installed on a vegetated mat over 10 cm deep substrate.
Table 3. Comparison of nitrogen (N) and

phosphorus (P) content in rainwater and run-off
from bare roofs and green roofs (vegetated mat)
Nutrient
content
Total N
(mg/l)
Total P
(mg/l)
Nutrient
content
Total N
(mg/l)
Total P
(mg/l)
Rainfall
0.51
0.007
Rainfall
0.6 - 1.3
0.012 - 0.019
Bare roof
run-off
0.896
0.197
Bare roof
run-off
1.4 - 2.6
0.102 - 0.104
Green roof
run-off
0.49
0.043
Green roof
run-off
1.2 - 2.1
0.026 - 0.09
Source: Gregoire BG, Clausen JC (2011) Effect of a modular extensive

green roof on stormwater runoff and water quality, Ecological
Engineering 37:963-969.
Source: Teemusk A, Mander (2007) Rainwater runoff quantity and

quality performance from a green roof: the effects of short-term
events, Ecological Engineering 30:271-277.
25
Most plants grown on a green roof require some fertiliser

application for them to grow well in the long term, and leaching
of nutrients into roof run-off will reduce water quality to some
extent. The nutrients of greatest concern in run-off water quality
are phosphorus and nitrogen: high levels of both cause algal
blooms in waterways. However, relative to the amount of fertiliser
initially applied to the roof, loss of nutrients into run-off can be
small. The benefit of a large reduction in stormwater volume
probably outweighs the cost of a small increase in nutrient loading.
This should be considered in relation to stormwater quantity and
quality requirements set by local water authorities.
The water quality from the outflow of green roof systems with
shallow or deep substrates was studied over nine months on a
rooftop in Adelaide. Controlled release fertiliser was applied at
the same rate to both green roof types. Run-off from the green
Evidence
roof areas with deeper substrates was of higher quality than that
off shallow substrates, lower total dissolved salts and electrical
conductivity, and there were lower sediment levels. However, there
was also a trend for elevated nitrogen (measured as nitrate) and
phosphorus concentrations in run-off from green roofs with deep
substrates: these nutrients are highly soluble so their appearance
in run-off is expected, but given that fertiliser application was the
same for both the shallow and deep substrates, it is noteworthy
that the deeper substrate did not provide greater nutrient
retention. Comparison of measured run-off quality against local,
state and national water guidelines suggest that green roof runoff could be recycled for irrigation and other non-potable use.
A link to the report is available from the Government of South
Australias Building Innovation Fund ANZ House Green Roof Trials
Stormwater Quality Monitoring.
Urban air quality

Many Australian and international studies show a link between
poor air quality and adverse effects on human health. This is
particularly evident for people prone to asthma and other
respiratory conditions, and those with cardiovascular disease. A
study by the Environmental Protection Authority, undertaken in
Melbourne between 1991 and 1996, demonstrated an association
between elevated nitrogen dioxide, carbon monoxide, ozone and
particulate air pollutants (such as smoke and dust) and mortality
due to cardio-respiratory disease, including asthma. This association
was strongest in warm weather, when ozone levels are high due to
increased production at higher temperatures and stable weather
conditions that reduce mixing of air.
As urban populations continue to grow, and even with
improvements in quality of motor vehicle emissions, it is projected
that the concentration of pollutants such as ozone and fine
particulate matter (PM2.5) will also rise. Management of pollution
requires control of emission sources and measures that reduce
the concentrations of pollutants in the atmosphere. Increasing the
amount of vegetation in urban environments is one such measure:
plant leaves absorb gaseous pollutants, while particulate matter can
fall onto leaves or be washed onto them by rain, and ultimately into
the growing medium, where it is degraded or stored.
Sources: EPA (2000) Melbourne Mortality Study: Effects of ambient
air pollution on daily mortality in Melbourne 1991-1996, EPA
publication 709; EPA (2013) Future Air Quality in Victoria Final
Report, EPA publication 1535.
The larger canopies of trees and shrubs offer the biggest surface
area for pollution capture, suggesting that green roofs with deeper
substrate, with the potential to carry a broad range of vegetation
types, will be an effective approach to pollution management at
height. However, as any increase in the surface area available to

absorb or adsorb pollutants offers the potential for improvement
of air quality, shallower green roofs, or walls and facades planted
with herbaceous species may still provide significant benefit. The
extent of pollutant capture will vary with the density of foliage
cover, and the degree of complexity of the leaf surfaces.
In narrow city streets at ground level (urban canyons), green walls
and facades offer the opportunity for improvement of urban air
quality in narrow spaces, by increasing the area that is covered by
vegetation and providing more potential surfaces for deposition
of pollutants. Measures of pollution capture in urban canyons
(and estimates from modelling studies) vary widely, as so many
factors contribute to the outcome, including the dimensions of the
urban canyon, and wind speeds through it. A study that modelled
the effect of vegetation in London street canyons estimated a
reduction of 15 per cent to 40 per cent for nitrogen dioxide and
23 per cent to 60 per cent for particulate matter concentrations,
respectively, with the adoption of green walls in an urban canyon
that was as wide as it was high.
Major findings are that significant reduction in both gaseous and
particulate pollutants are achievable with vegetation on roofs
and walls. This is achieved by direct capture of pollutants, and by
reducing building heat gain and associated localised warming of
the environment. All of these contribute to the creation of urban
heat islands and the generation of photochemical smog.
Source: Pugh TAM, Mackenzie AR, Whyatt JD, Hewitt CN (2012)
Effectiveness of green infrastructure for improvement of air quality
in urban street canyons, Environmental Science and Technology
46:7692-7699.
26
Evidence
Human health and wellbeing

During the Melbourne summer, the city often experiences several
consecutive days of hot weather. This is subsequently associated
with higher rates of illness and death: extreme high temperatures
are an additional stress to people whose health may already
be fragile, particularly the elderly. A report by the Victorian
Department of Health quantified the increased incidence of heatrelated illness and death during severe heat waves in January 2009.
During this time, there were 62 per cent more deaths than would
have been expected on average for this time of year, mostly in the
75 years or older age group. Keeping our buildings cooler through
increased shading is likely to contribute to a reduction in the loss
of human lives, and the demands on health services associated
with extreme hot weather.
Source: Department of Health (2012) January 2009 Heatwave in
Victoria: an Assessment of Health Impacts.
Vegetated environments are good for people. Traditional public
parks and open spaces provide refreshment and restful views,
space for recreation and cool areas of shade in summer, and
community gardens offer opportunities for food production.
These environments offer the potential for social interaction and
community building. They are good for physical and psychological
health and wellbeing and provide relief from the pressures of highdensity living. Cost estimates of morbidity and mortality associated
with the lack of access to green open space are not easy to dissect
as there are usually concurrent, co-dependent factors that limit
peoples ability to engage with nature. Exposure to nature improves
peoples ability to focus, cope with stress, generate creative ideas,
and decreases volatile, antisocial, behaviours.
Cities are noisy places to live in: construction, vehicular traffic and
the sounds of HVAC (heating, ventilation and air-conditioning)
equipment are constant features of Melbournes aural landscape.
Modelling studies show that although green roofs provide some
attenuation of noise, it is small: up to a maximum of 10 dB across
most of the frequency ranges that have been tested. Tests on a
range of green wall and facade systems in Singapores HortPark
revealed a similar outcome. So far, for green roofs, there is no
evidence for increased sound absorption beyond a substrate
depth of 20 cm (up to 40 cm). Any small decrease in the volume
of outside noise is an additional, unsolicited benefit of a green
roof, wall or facade. It has been suggested that the University of
Tasmanias green roof was a significant factor in sound reduction
emanating from its site, however the building had a number of
other technologies installed to reduce sound transmission, so
results cannot be attributed to the green roof alone.
Sources: Van Renterghem T, Botteldooren D (2008) Numerical
evaluation of sound propagating over green roofs, Journal of Sound
and Vibration 317:781-799; Wong NH, Tan AYK, Tan PY, Chang K,
Wong NC (2010) Acoustics evaluation of vertical greenery systems
for building walls, Building and Environment 45:411-420. Hopkins G,
Goodwin C (2011), Living Architecture, CSIRO Publishing.
Source: Townsend M, Weerasuriya R (2010) Beyond Blue to Green:

the benefits of contact with nature for mental health and well-being,
Beyond Blue Limited: Melbourne.
Property value
There is very little published research on the impacts of green roofs, walls or facades on property value. Research in Canada estimated
that buildings with a recreational green roof achieve an 11 per cent increase in property value, and buildings with views onto green roofs
have a 4.5 per cent increase in property value.
Source: Tomalty, R. & Komorowski, B. 2010, The Monetary Value of the Soft Benefits of Green Roofs, Smart Cities Research Services, <http://www.
greenroofs.org/resources/Monetary_Value_of_Soft_Benefits_of_Green_Roofs.pdf>
27
Green roofs research

at The University
of Melbourne
Since 2008, researchers at The University of Melbournes
Burnley campus have undertaken research evaluating
green roofs for Australian conditions, with a focus on
plants, substrates, hydrology, energy use and environmental
psychology.
Experiments on roofs and in controlled environments have
quantified the performance of 56 different plants, including
both Australian native and exotic species. For survival in the
absence of irrigation, plants with low water use and high leaf
succulence, such as Sedum pachyphyllum and S. xrubrotinctum
proved to be the most successful. However, to reduce
stormwater run-off from green roofs, plants also need to
dry out substrates between rainfall events, a feature that low
water use succulents are incapable of. This research showed
that plants from specialised natural habitats similar to green
roofs, such as rock outcrops, can balance high water use with
high drought tolerance. The most successful species included
Dianella revoluta, Stypandra glauca and Lomandra spp. An
additional benefit was the capacity of these plants to re-sprout
following desiccation, further improving survival after drought.
Evidence
greatest from the bottom ash substrate (bare and planted)

and significantly less in scoria. Water retention also differed
between substrate types, with scoria retaining at least 20 per
cent less rainfall after large events than both bottom ash and
roof tile substrates, probably due to lower evapotranspiration
from scoria between rainfall events. Results of an energy
study completed in 2009 showed that a 125 mm deep scoria
substrate green roof reduced building energy use by 38 per
cent on a summer day.
Environmental psychology research demonstrated that
people prefer meadow-like green roofs, dominated by green
strappy or grass-like plants. The addition of flowers on the
green roof further increased preference scores. Viewing this
type of green roof was also found to improve concentration
and could result in improved workplace productivity.
The development and analysis of lightweight growing

substrates, based on mineral and waste components, such
as scoria, crushed roof-tiles and bottom ash (wastes from
coal-powered electricity generation) has led to multiple
green roof installations across Melbourne. This work also
included testing and evaluating a wide range of substrate
components and mixes, and investigating the use of waterretention additives in substrates, such as silicates, hydrogel
and biochar. Of these, biochar was the most effective,
resulting in lighter substrates that held more water and
delaying the onset of permanent wilting in test plants by up
to two days. This research also showed that the effectiveness
of retention additives varied, depending on substrate and
additive properties (for example fine silicates were ineffective
in coarse-textured substrates).
Hydrology research under natural rainfall conditions
found that a 100 mm deep scoria substrate can reduce
stormwater run-off in Melbourne by 43 per cent to 88 per
cent, depending on the season. Further work evaluated the
influence of three different substrates (bottom ash, roof
tile and scoria) and succulent vegetation cover (planted vs.
bare) on evapotranspiration and retention capacity under
simulated rainfall conditions. The results showed that the
effect of plant cover was influenced by season with greater
evapotranspiration in spring. Planted modules also retained
more rainfall than bare modules for medium and large rainfall
events and overall the cumulative evapotranspiration was
Green roofs research at The University of Melbourne includes

survival experiments in greenhouses and on roofs, and hydrology
experiments in controlled environments under cover
Green walls were installed on four aspects of the tower block used in the 2013 TV series The Block Sky High, 142 Park St, South Melbourne.
Image: Fytogreen
SECTION
03
Technical Guide
30
Technical Guide
Technical
Guide
This Technical Guide provides advice on the factors that need to

be considered to design, construct and maintain green roofs, walls
and facades.
The Growing Green Guide is the first publication in Australia to collate
such technical advice through independent agencies. It is likely that
over time the industry will mature and have a body of research
and experience that can be used to move from advice to technical
standards that are directly relevant to Australian conditions.
Introduction
Refer to the introductory section of this guide for definitions of
green roofs, walls and facades. A glossary of other terms follows
Appendix A at the end of this document.
Including this Introduction, the Technical Guide has been divided
into eight chapters covering the following areas:

Chapter 2. Site Analysis

Chapter 3. Design and Planning
Chapter 4. Building and Installation Background Advice
Chapter 5. Building and Installation Green Roofs
Chapter 6. Building and Installation Green Walls
Chapter 7. Building and Installation Green Facades
Chapter 8. Maintenance
In Appendix A you will also find specific and detailed information

about green roof growing substrates.
If, after reading this guide, it appears that green roofs, walls or
facades are not suitable for a particular building, consider other
greening options, from balcony plantings to backyard and naturestrip gardens. This guide does not cover these options, but many
books and websites are dedicated to these opportunities.
This guide has been published under Creative Commons licencing
as an invitation to others to adapt, update and improve the
guidelines as new technology is developed and research improves
our knowledge.
While it provides the key relevant information on this subject at
its publication, for more detailed information and updates visit the
Growing Green Guide website: www.growinggreenguide.org
The first step in any roof, wall or faade project is to visit the site and understand the local environment and built infrastructure. Image: ASPECT Studios
2. site analysis
Before designing a green roof, wall or facade it is important to understand the
characteristics of the site, as these factors will influence the feasibility and cost.
This chapter explains how to evaluate a proposed location for a green roof, wall
or facade. It is written for situations where there is an existing building on-site,
however it can be adapted by those planning to construct a new building.
32
Site
Site Analysis
2.1 Climatic factors on-site

Climatic factors will vary with geographic location as well as with
the site aspect and height and even from effects of surrounding
buildings. It is important to understand the likely climate onsite in order to inform decisions about which plant species are
suitable for the site. There are no hard and fast rules about what
constitutes too much wind or shade or other factors; rather,

these are environmental gradients (for example, low wind to high
wind) and often the best approach is to estimate the worst case
scenario for plant growth that is likely on-site, and design with that
in mind.
Wind
Average wind speeds are greater at height than at ground level. Winds may be strong
around the edges of buildings, or from the down draft caused by tall buildings. It is
necessary to understand the likely wind load that a green roof, wall or facade will be
subjected to, so that it can be built to withstand the forces. Wind at high elevation will
also influence temperature, and wind has a direct dehydrating effect on vegetation,
therefore influencing species selection and irrigation requirements. See the Freshwater
Place and Victorian Desalination Project green roof case studies in this guide to learn more
about the challenges of wind.
Rainfall and
irrigation
Rainfall in Melbourne is generally not sufficient to support a green roof, wall or facade
throughout the year. It is important to establish whether rainwater or another water
source can be harvested from other areas on-site, and stored to supply an irrigation
system. This will avoid or minimise the need to use potable water for irrigation. It is
useful to carry out an irrigation water demand analysis, to estimate water needs.
Solar radiation
Light intensity tends to be greater at height than at ground level. At height there are
fewer structures, no vegetation to absorb solar radiation and increased reflection from
adjoining building and surfaces (such as glass and light-coloured walls). Conversely, there
are some roofs and walls that may receive significantly less solar radiation, due to intense
shading by nearby buildings. Shadowing and shading analysis can be used to assess areas
of light and shade on a site and possible changes over the year (for example, at the
equinox) and over time (for example, adjoining new building development).
Temperature
Microclimate
In urban environments temperatures tend to increase with elevation, due to the

increased thermal mass of built structures and the commensurate heat gain. Assessing
the likely temperature range on a site is crucial in planting design, particularly in extreme
temperature events. While cold temperatures are rarely a problem for vegetation in
Melbourne, there can be localised green roof situations where this could be a factor in
plant selection.
Enclosed spaces such as urban canyons can create their own microclimate where wind
turbulence, pooling of pollution, humidity and temperature can be intensified. The
localised climate of these areas will change the growing conditions for plants and needs
to be considered when planning and designing green roofs and walls.
33
Site Analysis
Site
Climate and rooftop

vegetable production
The Pop Up Patch is a subscriber-based edible
gardening club, based on a car park roof behind
Federation Square, in central Melbourne. The Little
Veggie Patch Co. runs the garden and has to allow
for the different climate that comes from being
based on a roof. The concrete roof stores heat
and the warmer temperatures mean that species
that might not normally have been considered
suitable for the area can grow. Some species that
are usually annual begin acting like perennials.
For instance, they have found that capsicums
and chillies survive and continue to fruit through
the winter months in this location. The warmer
temperatures necessitate growing substrate with
a high water-holding capacity. In addition, the winds
at height dry the surface of the substrate, so drip
irrigation underneath a layer of mulch is highly
recommended.
Light reflection and wind tunnelling effects from surrounding

buildings, will influence the climate on-site, along with local rainfall
and temperature
Pop Up Patch finds that a warmer climate on a car

park roof changes the growing season of some plants
34
Site
Site Analysis
2.2 Weight loading

The load-bearing capacity of a building must be known before
planning a green roof, wall or facade. A structural engineers advice
is essential to ensure comprehensive design development, based
on the buildings construction, condition and weight loading capacity.
For retrofitting a green roof, wall or facade, it is important to
establish early whether the installation will meet the existing
structural capacity of the building, or whether this will be modified
to support the installation. In some instances, it is possible to
strengthen an existing roof in strategic areas (and not across the
whole roof) in order to achieve the design outcome while also
minimising costs.
It is important to consider not just the weight of plants when

planted but their weight at maturity, especially where shrubs and
trees are proposed, as these are likely to be significantly heavier
over time. The weight of saturated plants and substrate must
also be included in the load assessment. Some example weight
loadings of plants are provided in Tables 4 and 5.
Damage to a wall can arise from wind forces, plant load, cable
tension, and human access. This is particularly important where
older walls are being used and where there is a large surface area
of green facade (that is, wind uplift).
For a green roof, wall or facade, the loads that the building structure must support include:
Dead load
The final constructed weight of all built elements and all components associated with the
roof or wall assembly, including plants, growing substrate and any water held in the system.
Live load
The weight of people who will use the space, and of any mobile equipment that will be
used periodically on the site, for example, maintenance (live load generally applies to
green roofs, not facades or walls, however it would be appropriate on a vertical surface
if a trafficable maintenance platform was built into the system).
Translent load
Moving, rolling or short-term loads, including wind and seismic activity.
Table 4. Weight loadings for some representative climbing species
Species
Weight loading (kg/m)
Jasminum (Jasmine), Rosa (Rose)
6 - 12
Clematis (Clematis), Tropaeolum (Flame Nasturtium)
3 - 12
Vitis (Ornamental Grape), Ampelopsis (Porcelain Vine)
12 - 26
Lonicera (Honeysuckle), Actinidia (Kolomitka), Wisteria (Wisteria)
10 - 26
Source: Jakob Rope Systems

Note: these are figures from the Northern Hemisphere, where the effective growing season is shorter than Australias. Weight loadings
are therefore likely to be an underestimate
35
Site
Site Analysis
Table 5. Green roof vegetation weight loadings
Green roof vegetation type
Weight loading
(kg/m)
Low herbaceous (succulents

and grasses)
10.2
Perennials and low shrubs up

to 1.5 m
10.2 20.4
Turf
5.1
Shrubs up to 3 m
30.6
Small trees up to 6 m
40.8
Medium trees up to 10 m
61.2
Large trees up to 15 m
150
Source: FLL Guidelines
Some load-bearing
capacities used in
design of Melbourne
green roofs and walls
The University of Melbournes demonstration
green roof is designed for use by visitors and
staff. It is built on a heritage-listed brick building in
Burnley. It has areas of deep and shallow substrate
and is designed for a dead load of 300kg/m2 and a
live load of 300kg/m2 on the decking and walkway
mesh and 150kg/m2 on the planting area.
The Venny green roof has shallow substrates on
two types of roof, the first roof is on shipping
containers, and is designed for a dead load of
250kg /m2 and live load of 100kg/m2. The second
trussed roof is designed for a dead load of 160kg/
m2 and a live load of 40kg/m2.
The Triptych external green wall and the Telstra
Conference Centre internal green wall are both
designed for a dead load of 80kg/m2.
Demonstration Green Roof at The University of

Melbournes Burnley campus has a maximum
capacity of 100 people
Green roofs at the Venny, Kensington are not designed

for people to visit, other than for maintenance purposes.
36
Site
Site Analysis
2.3 Drainage
Sites for green roofs should be assessed for drainage. Check
whether the site has primary and/or secondary drainage systems
(illustrated in Figure 13).
the roof s design weight loading. The need for overflow relief will
be established by looking at existing performance of the drainage
in conjunction with the historical data on rainfall intensity.
Primary roof drainage systems may use:
Removal of water from any roof surface is assisted by some degree

of pitch or slope. Even roofs that look flat have a gentle fall to
promote movement of water into the roof drains, to prevent ponding.
Ponding refers to water that remains on a roof for extended
periods after the end of the most recent rain event (Figure 14).
Recurrent ponding can cause lasting downward deflection of the
roof structure, which over time may reduce the efficiency of
drainage and cause the roof to become unstable. A pitch of at
least two per cent reduces the risk of ponding, and a steeper pitch
means the roof will drain more quickly. Strengthening the roof
construction to reduce deflection may be needed.
box gutters (for near-flat roofs) or eaves gutters

(for pitched roofs)
simple waterspouts (also known as scuppers)
outlets or box drains built into the roof
These are collector drains that are designed to flow when only
partly full. Primary drainage systems are not designed to remove
all of the water that falls on a roof during exceptionally heavy rain.
A green roof may require a separately plumbed secondary drainage
system, also known as the overflow relief system. For flat or nearly
flat roofs, primary drains are located at the lowest point of the roof:
flow of water into them is promoted by positive drainage.
Secondary (overflow) drains are located at a higher point on
the roof. These are designed to operate in a worst-case scenario
where the primary drains are completely blocked and water
builds up on the roof due to a torrential downpour of rain and/
or a failure of the irrigation system to shut off. Overflow drains
remove accumulated water to a depth that the roof can carry
without becoming unstable, and ensure that the roof weight
loading capacity is not exceeded. For roofs with a very low
parapet, overflow drainage may be achieved simply by flow over
the roof edges, if accumulation of water to this height fits within
Figure 13. Different types of roof drains
When assessing the site and planning for the design of a drainage
system, consider:

the amount of rainfall that lands directly on the site, and any
that drains onto it from adjacent roofs or walls
length of rainfall event estimated from historical records
and forecasts of future extreme rainfall events under a
warmer climate
the speed at which rainfall will collect at the drains
(determined primarily by roof pitch)
the planned capacity of drains, including the drain dimensions
and diameter of gutters and drainpipes
Figure 14. Water ponding on a roof
Ponding
Eaves
gutter
Water
spout
Roof
outlet
Overflow
drain
Design of drainage systems must be matched to the roof

construction and catchment area
Internal Drain
Accumulation of water on a roof can cause downward

deflection that reduces the efficiency of drainage systems.
37
Site
Site Analysis
2.4 Existing
structure and size
2.6 Nearby
vegetation
Consider the quality of the roof or vertical surface Is it

currently waterproofed? Does the wall have a surface that needs
protection from vegetation?
The local vegetation adjoining a site can influence design.

If creation of habitat for biodiversity is a desired outcome
for your green roof, wall or facade, consideration of the
surrounding landscape could be useful. However, nearby
vegetation can also be a source of weeds or contribute to
a fire risk and should be included in site analysis.
Assess the area available bearing in mind that costs increase

with size. The useable area can be diminished if there are many
windows on a wall or numerous vents and equipment on a roof.
Roof slope green roofs are ideal on slopes less than 15 degrees
but can be constructed on steeper slopes with special materials.
Water collection and storage opportunities - is there space to
store water on-site? Tanks are usually located at ground level or
in the basement of a building, and an irrigation tank may be colocated or shared with tanks for toilet flushing. Water storage can
also be built into the design of some green wall systems.
2.5 Access
Evaluation of the site should review accessibility. Temporary
access will be needed for machinery, and delivery and storage of
materials during construction. For green roofs or multi-storey wall
and facade greening, this might involve a crane to lift materials
onto the site.
Consider how people will access the installation for maintenance,
viewing or standing on. This might require stairs, lifts and viewing
platforms for the general public or building tenants. It may also
require balustrades, cables for attaching harnesses and ropes (fixed
fall protection), ladders, elevated work platforms independent of
the building, or swing stages mounted on the top of the building
for maintenance personnel. Access for maintenance to walls and
facades can also be considered from below, in which case space
for a temporary elevated work platform is likely to be required.
Further information about site safety is provided in Chapter 4.
Access for passers-by must also be considered, as there are
regulations against vegetation that protrudes onto public space,
and even in the private realm it is important to be aware of
hazards that can be created for people using the space nearby.
Good access is needed to deliver materials safely onto a

green roof during its construction. Ease of access to the site
will greatly influence the cost of the installation.
38
Site
Site Analysis
2.7 Site assessment summary

The table below outlines information that is required in the
analysis of a site for a potential green roof, wall or facade. Some of
these elements will require specialist knowledge; for instance, the
weight loading that can be applied to a roof or wall, will require
consultation with an architect and structural engineer.
Other issues can be answered either by direct observation on the

site or through the use of downloadable resources, such as climate
data for the local area from the Bureau of Meteorologys Climate
Data Online. The information collected will help determine the
design and planning of the green roof, wall or facade.
Table 6. Site analysis requirements
Information to collect during site analysis
Seasonal
considerations
and climate
Expected maximum and minimum temperatures.

Expected rainfall volume and distribution throughout the year.
How sun, shade, wind vary on the site throughout the year.
How the height of the building might influence some climatic factors.
Forecasts on how the local climate might change over time.
Local environment
Assessment of opportunities or risks that nearby vegetation will have on the site - fire threat,
weed or pest invasion, biodiversity migration.
Weight loading
Load-bearing capacity.
Estimated transient loads, particularly wind forces.
Drainage
Storm water discharge points.

Assessment of whether drainage will be sufficient in the case of severe weather.
Irrigation
Water collection and storage opportunities, opportunities for delivery of irrigation water and for
co-locating stored water with other grey water systems in the building.
Existing structure
and size
Size of useable roof or wall area.

Available space for plants to be grown from ground level upwards.
Any slopes or angles to the roof or wall.
Quality of existing roof and wall materials.
Access
Access to site for cranes and other machinery, and for storage of materials during construction.
Access for maintenance and/ or visitors (consider safety such as a parapet on a
roof and disability access requirements too).
Access to utilities - water, electricity.
Ensure access for passers-by is not impeded.
39
Design & Planning
Design
A concept design for a green roof in Melbourne. Image: Bent Architecture
3. design &
planning
The most important decisions about a green roof, wall or facade are made at
the design stage. The benefits of the installation, how easy it will be to build and
maintain and how it will operate day-to-day, all depend on the initial design. This
chapter provides information to help develop a well-considered, achievable
design that will work in the long term.
40
Design & Planning
Design
Along with understanding the site conditions (see Chapter 2), other
important issues to consider at the design stage are:

overall design outcomes sought from the project

drainage and irrigation
maintenance inputs
sourcing the right information and expertise
budget
relevant building industry codes and planning assessment tools
plant selection and establishment
Consideration of these issues is crucial to the successful design of

a green roof, wall or facade, and should be well thought out before
planning for construction.
A range of factors needs to be considered when designing a green roof, wall or facade. This residential green roof in Brunswick, Melbourne, was
constructed over a small area due to budget constraints, and was planted with hardy flowering plants because its purpose was aesthetics with
minimal maintenance. Information was sought from green roof providers and the local nursery, prior to construction. The level of detail needed in the
design and planning stage will depend on the scale of the project being undertaken.
41
Design
Design & Planning
3.1 Design objectives

The fundamental reason for undertaking a green roof, wall or
facade project needs to be identified up front, as this will influence
the design, construction and required level of maintenance for
the system. When building a green roof, wall or facade on behalf
of someone else it is crucial that the clients requirements are
understood. For example, a green roof designed for the purpose
of increasing aesthetic value might focus on species of ornamental
significance more so than drought tolerance or low maintenance.
However, the same design might not be suitable for a client who
wants a low maintenance, water efficient installation.
The following tables provide some examples of different

considerations needed for different design goals. This is not an
exhaustive list, and it has some very simple considerations: it is
intended only to illustrate that different goals will require different
inputs and system set-ups. Discussions with professional green
roof, wall and facade installers, landscape architects and a review
of relevant research will be needed to make final decisions about
the most appropriate approach.
It should be noted that green roofs, walls and facades will be part
of a broader urban green landscape and their design should ideally
ensure that they contribute to the goals for the surrounding
landscape, along with street trees and other forms of green
infrastructure.
Green roof design goals
Considerations
Reduced stormwater run-off
Increase depth and water-holding capacity of substrate, use plants with high
water uptake.
Recreation and amenity use
Increase weight loading, ensure ready roof access, planning and safety
requirements.
Lightweight, long-life and no irrigation
Choose stable, lightweight substrates and components, and high stress

tolerant plants, e.g. succulents.
Cooling and integration with

photovoltaic panels
Select leafy plants, provide irrigation, plant around (but do not shade)
solar panels.
Maximise thermal insulation
Increase substrate depth, provide irrigation, select species for leafy plant cover
in summer (passive heat gain in winter may be increased if the roof is bare in
winter but this strategy increases maintenance and reduces aesthetic benefit).
Provide biodiversity outcomes
Include habitat plants (usually native/indigenous), habitat features (such as

water and shelter), small changes in topography and variations in substrates.
See Green roofs for biodiversity following.
Produce food
Increase weight loading capacity of the roof, and depth and organic content
of substrate, ensure good access to the site, provide irrigation.
42
Design
Design & Planning
Green wall design goals
Considerations
A multi-storey green wall
Ensure access for maintenance is possible, consider hydroponic system

if weight loading is likely to be a problem, ensure species selection is
appropriate for the specific light and wind exposures at different heights.
Aesthetics and a design statement on

a building
Include a variety of species with different flowering times, consider planting in

patterns and consider textures, foliage colours and extending the planting area
beyond the boundaries of the green wall surround.
Low cost and easy to install on a

residential building
Consider DIY installations, minimise the size of the system, self-contained units
that recirculate water, systems that can be easily replanted.
Include a variety of species with habitat features such as fruits or nectarproducing flowers, or a niche design that provides protection from predators
for particular species.
Internal green wall
Ensure adequate light possibly install artificial light.
Long lasting wall
Consider quality of design and longevity of components.
Green facade design goals
Considerations
Low cost and easy to install
Use a direct attaching species of plant, grown from the ground at the base
of the wall.
A multi-storey facade greening
Include containers at different heights, include cabling or lattice support

structures for twining plants, ensure access for maintenance, provide
irrigation, consider secondary protection of plants against stem damage,
e.g. wind protection trellis.
Screening of an unsightly view
Use evergreen species to ensure year-round screening, create a structure for

the plants to grow on.
Maximise thermal benefits
Use deciduous species if heat gain is desired in winter; ensure very leafy
plants, covering the entire wall for providing best shade in summer, particularly
on north and west facing walls; provide a structure at least 100 mm off the
wall of a building for the plants to grow on, leaving an air gap between the
building and green plants to maximise cooling effect.
Produce food
Increase depth and organic content of the substrate, ensure good access to
the site, provide irrigation.
Include a variety of species, with habitat features such as nectar producing

flowers, fruits, capacity to support nests, create protected or visually
prominent areas.
43
Design & Planning
Design
Green roofs for biodiversity

Green roofs that are designed to increase biodiversity should
feature indigenous vegetation local to the area. Biodiversity
roofs should also incorporate different vegetation layers and
landscaping features to increase opportunities for wildlife to feed
and shelter.These may include hollow logs or twig bundles, rocks,
different substrate types, such as areas of sand or rubble, and
spaces for shelter, such as roof tiles and nesting boxes.
The value of green roofs for biodiversity will depend on their
characteristics and location. In general, larger green roofs on
relatively low buildings closer to natural areas will be more
valuable than small, high green roofs in dense urban areas
remote from parks or native vegetation remnants.
In the Northern Hemisphere, biodiversity roofs often have
only a shallow (< 150 mm) depth of substrate, and receive
little to no irrigation or maintenance. In most parts of
Australia, the longer growing season and typically hot, dry
summers make it unlikely that herbaceous vegetation on
shallow green roofs could be sustained in the long term.
The Biodiversity Roof at The University of Melbournes Burnley

campus includes a range of substrate types and features to
provide habitat opportunities for small wildlife. Note that this
image shows the roof soon after construction. The plants will
grow larger and less substrate will be exposed over time.
Source: Peter Casamento
Irrigation may need to be provided during hot dry periods to

ensure greater vegetation success. The vegetation must not
create a fire hazard or block drains, so non-vegetated areas
around the roof perimeter, drains or other fixtures must be
kept clear.
If a low to no-maintenance approach is taken for a
biodiversity roof, there must be an understanding that some
plant species may be short-lived. Species persistence can
be improved through plants that readily seed and self-sow,
or produce underground storage organs (bulbs or tuberous
roots) that are dormant for part of the year.
Planting a diverse range of species on a green roof is more
likely to attract a broad range of invertebrates, birds and
other wildlife than a monoculture of a single species.
The Biodiversity Roof at Minifie Park Early Learning Centre

includes plants found in the local area. Image: Jacinda Murphy
Both of these roofs are featured as Growing Green Guide
case studies
44
Design
Design & Planning
Urban food production

Just as walls and roofs of buildings provide a surface for
greening in dense urban areas with very little ground-level
space, they also represent a possible location for urban food
production.
In some parts of the world large areas of rooftops in inner

urban areas are being transformed into urban farms. More
commonly, roofs are used to house hydroponic or containerbased plots for food production, such as the Pop Up Patch at
Federation Square, Melbourne.
Walls have only been experimented with on a small scale.

Facades tend to lend themselves to the production of food
from climbing plants such as beans or passionfruit.
Some of the challenges to be overcome with rooftop and
vertical food production include:

access for harvesting the produce

load-bearing capacity that will allow for the
necessary numbers of people and equipment
needed at harvest time
ensuring the produce is not contaminated from
pollutants in the air research is being conducted
on this. Note that research from Germany on urban
horticulture production relates the contamination to
traffic levels and indicates that a building is a barrier to
pollution from traffic, indicating that walls and facades
should be away from heavily trafficked roads but
perhaps roofs will be buffered simply because they are
away from the roadside
sustainable water use food-producing plants tend to

need a lot more water than a number of other plants
typically found on roofs, walls and facades. So it is
imperative that rainwater can be collected, and possibly
recirculated, to irrigate large urban agriculture plots
nutrient management every crop harvest takes
nutrients out of the system, so to keep adequate
nutrition up to food-producing plants, growing substrates
will need to have either a higher organic matter rate
than traditionally used in facades or roofs or more
nutrients will need to be applied to the plants. This will
necessitate close monitoring of run-off to ensure that
the water leaving the site is not polluted.
As the issue of adequate plant nutrition is so crucial to food

production, it is uncommon to see examples where urban
agriculture is practiced on roofs where the layers are looselaid, rather than in containers. Where containers are used it
is possible to remove all the growing substrate and replace
completely. In fact, there are some urban agriculture rooftops
where the food is grown on hydroponic systems on the roof
to avoid the need for a growing substrate altogether.
Urban agriculture on roofs and walls can be part of
community gardens, private residences, school farms, social
enterprises or may have potential to be commercial farms.
The scale of the project and intended level of production will
determine how the challenges above are dealt with. Careful
consideration needs to be given to plant selection as roofs
and walls can be much hotter, darker or more windy than
ground sites.
Edible plants in a rooftop garden in Marion, South Australia (Image: Fifth Creek Studio), at the Pop Up Patch gardening club in
Melbourne, and in a trial of vertical vegetables, in Perth, Western Australia (Image: Walls Alive!)
45
Design & Planning
Design
3.2 Planning for drainage and irrigation

Good drainage ensures that the green roof, wall or facade does
not compromise the structural integrity of the building and that
plants are not adversely affected by waterlogged substrate. A
drainage system must effectively remove surface and sub-surface
water from the roof or wall.
While green roofs, walls and facades are able to reduce the flow
and assist in retaining stormwater run-off, it is still necessary to
have drainage systems that can cope with extreme rainfall events
or flooding caused by other factors on the site. See Chapter 2
for more information on drainage systems. All roof drainage
systems (green or otherwise) should be designed to handle the
most intense 60-minute duration rainfall that has a one per cent
probability of being exceeded in one year (in Melbourne, this is a
48.5 mm rainfall event but is subject to change). Green roofs will
not directly increase drainage needs on a roof, however design must
ensure that excess surface run-off can be discharged readily through
the roof drainage system. The components that make up the
substrate will affect the flow of water through a green roof profile.
Irrigation is critical to the success of most green roofs, walls and
facades, and many green walls have a particularly high water
demand. It is strongly recommended that non-potable water
sources for irrigation are explored, particularly for systems/designs
that are water intensive. The likely water demand of vegetation
can be estimated by developing a water budget based on multiple
characteristics of the green roof, wall or facade, including:

A number of horticultural publications provide more information

on these issues, including Growing Media for Ornamental Plants
and Turf (Handreck and Black), Water Use Efficiency for Irrigated
Turf and Landscape (Connellan) and Water Use Classification
of Landscape Species a method for estimating the water
requirements of landscape plants, based on species, vegetation
density, and microclimate (University of California Cooperative
Extension and the California Department of Water Resources).
Sustainable design of green roofs, walls and facades should
incorporate key principles of water sensitive urban design
(WSUD), particularly to manage stormwater in the landscape,
rather than into the stormwater drainage system. For green roofs
in particular, it is desirable to maximise water retention in the
system for as long as possible, and to send reduced volumes of
high quality (low nutrient) run-off off the roof. Re-use of irrigation
water is useful in green roof, wall and facade installations, where
large volumes of water flow through the system. Treatment to
disinfest and treat run-off water is needed in these situations as
continuous recycling of untreated water can spread soil-borne
disease and/or lead to the build-up high levels of nutrients.
In many green wall installations, water reticulation and reuse is
standard practice.
More specific advice on drainage and irrigation for green roofs is
available in Chapter 5.
calculating total water needs based on the landscape

coefficient or crop factor values (see Glossary)
evaporation data
effective rainfall
the capacity of the substrate to store water
This green roof at the Peter Doherty Institute, Grattan Street, Parkville,
functions as a grey water treatment system. Image: Eco Harvest
Laying irrigation pipe at Minifie Early Learning Centre green roof.

Image: Junglefy
46
Design
Design & Planning
3.3 Designing for maintenance

Design and planning of a green roof, wall or facade must
incorporate an understanding of how the system will be
maintained. Buildings owners and property managers need to
understand what is involved in maintaining the roof, wall or facade
and must be committed to managing it, otherwise the benefits
outlined earlier in this document may not be achieved.
The systems, or assets, created must not exceed the skills,
technologies and resources of those who will be given the
responsibility for their maintenance. There are examples of green
roofs in Melbourne that have been designed which require
complex horticultural management, but the management has
fallen to contract staff with no specialist expertise in green roofs,
and the landscapes begin to deteriorate. This can result in user
complaints and/or the need to replace an asset prematurely,
which is inefficient and unsustainable both economically and
environmentally. It may be that the green roof, wall or facade
provider is best placed to undertake on-going maintenance on a
contract basis.
The person or team with ultimate responsibility for management
of the project/property must be clear about maintenance objectives
and their capacity to undertake them with available resources. All
design options proposed must be fully evaluated in terms of the
maintenance they will entail.
Including ongoing maintenance costs is an important part of the

design considerations, especially from the point of view of the
client, or asset owner. To determine the ongoing maintenance
requirements of a green roof, wall or facade consider engaging
a consultant or contractor with relevant experience. Advice
can be provided on the resources needed to maintain different
design options and the likely expenditure needed to maintain
the materials used. For large commercial projects, a maintenance
impact statement can be provided by the landscape designer.
Alternatively, specify maintenance objectives and standards early,
so that the designer has these in mind to start with. Chapter 8
provides information on common maintenance tasks and the
development of a maintenance plan.
Consideration may be needed for renewal or removal of a green
roof, wall or facade, especially where a temporary or short-term
installation is proposed. The Melbourne Central shopping centre
green wall was designed as a temporary installation, however
with various interventions its life was extended for some years.
Ultimately it was dismantled due to high maintenance costs for a
wall in a position with very limited light. Although roofs, walls and
facades can, of course, be designed from the outset to last for
decades, in some cases they will be designed for a limited lifespan
and therefore the opportunities for renewal or process for
removal should be considered in the design stage.
3.4 Sourcing skills, expertise and

information
Most projects require the involvement of a number of different
trades and skills, and the more complex the project, the more
elements there are to coordinate. It is crucial that a specialist,
experienced, green roof, wall or facade designer is engaged
during the design and consultation phase, rather than at the
end of this process.
Although there are no Australian standards for the specific
purpose of green roof, wall or facade installation, some Australian
building code standards are relevant. International standards that
are often referred to in Australia are the German FLL guideline,
ASTM International (formerly the American Society for Testing
and Materials) and Singapores Centre for Urban Greenery and
Ecology (CUGE). See Standards in the References and source
material section of this guide for more information.
The website of Green Roofs Australasia features a business

directory covering aspects of green roof, wall and facade design
and construction. The Landscaping Victoria website provides a list
of commercial and residential landscape contractors, landscape
designers, and landscape service and product suppliers. There
are a number of useful books on various aspects of green roofs,
walls and facades, some of which are listed in the References and
source material section of this guide.
You may need to consult with various professionals, some of
them possibly on an ongoing basis, throughout both the design
and construction phases of your project. For small-scale projects,
a green roof, wall or facade provider will often supply several
services, from engineering to irrigation to project management
and design. In other cases, it will be imperative that the provider is
collaborating with the rest of the design and project management
teams.The following list describes specific areas of expertise involved.
47
Design
Design & Planning
Project manager
Leak detection specialist
Develops a project timeline

Manages construction budget and payments
Ensures contractors have appropriate registration, licensing,
insurance and working at heights training
Manages site inductions for all personnel
Construction manager /
Principal contractor
Horticulturalist

Plans and oversees construction activities

Engages contractors, or sub-contractors
Architect or landscape architect
Designs the project, working with the client to select the

most appropriate system for the site, including consideration
of how it will be managed and maintained in the long term
Coordinates planning and building permits, either directly
or through a building surveyor
Reviews progress and inspects construction
Provides advice on the installation in the context of the
whole site/landscape
Note: architects and landscape architects with experience and

specialised knowledge of green roofs, walls and facades will be
best able to provide conceptual designs and specialised design
of support structures and plantings.
Structural engineer

Examines the existing building, or the proposed design for

a new building
Determines the structural elements required to achieve
the desired weight loading
Builder

Constructs the building, or installs any structural

reinforcement needed in a retrofit green roof project
Installs any built-in elements associated with the roof, wall
or facade, often in conjunction with the green roof, wall or
facade provider
Designs and installs the green facade

Provides advice on the most appropriate treatment for the
site, including plant selection, irrigation, cabling, trellising and
container-growing systems, and ongoing management
Irrigation consultant / Hydraulic engineer

Reports on the condition of the existing roof (retrofit), and

recommends the most suitable waterproofing for the project
Prepares the roof and installs waterproofing
Designs and installs the green wall

Provides advice on the most appropriate treatment for
the site, including plant selection, irrigation and ongoing
management
Green facade provider
Provides design advice to architect/landscape architect (or

may undertake all design work in a small project)
Provides advice on all elements required for the green roof
build
Supplies and installs all green roof elements, usually including
growing substrate and plant materials
May provide advice on maintenance and long-term
management requirements
Green wall provider
Waterproofing supplier and

contractor
Provides advice on growing substrate

Recommends and sources suitable plants
Seeks specialist advice (for example, arboricultural advice for
tree selection)
Coordinates delivery and installation of plant materials
Green roof provider
Building surveyor
Reviews and approves building plans
Reviews construction for compliance with the regulations
Arranges for Building Permits and Occupancy Permits with
local councils
Carries out leak testing at specified stages of construction,

and as part of regular scheduled maintenance
Advises on a suitable irrigation system during the design

process based on the proposed substrate depth/volume and
water-holding properties
Advises on use of recycled/harvested water, pumps, and
storage tank volumes and configurations
Advises on approaches to sustainable and efficient water
management in the context of the whole site (water sensitive
urban design)
Advises on integration of the irrigation system with the rest
of the buildings water system
Landscape manager /
Maintenance manager

Oversees maintenance contractors

Negotiates and manages contractual arrangements
Allocates budget and resources to maintenance activities
48
Design
Design & Planning
3.5 Cost considerations

Each roof, wall or facade will vary significantly in terms of cost,
depending on the design site, the system installed and the
construction materials used. Costs can be reduced in small projects
as do it yourself (DIY) installations, involving less personnel and
smaller spaces. There may also be economies of scale for large
projects which will bring costs down, especially if there are other
efficiencies in terms of access for construction, and if the build
already lends itself to a green roof, wall or facade.
Generalisations of costs, based on 2013 prices, are provided
opposite, and are indicative only as each project will present
different opportunities and challenges. The case studies included in
this guide (Section 4) provide an indication of costs of particular
installations (at the time of their construction). Up-to-date pricing,
and advice on the costs likely to apply to a particular project
site, need to be sourced from expert practitioners, providers,
architects and engineers.
Construction costs will vary according to some of the following issues:

type of structure (and any need for structural

reinforcement)
design
site location, size and access
distances for transport
storage of materials on or off-site
access for mobile cranes, access to goods lifts
roof height, dimensions and load-bearing capacity
roof construction, complexity of roof design including roof
penetrations
timing of project, including contract growing of plants
Typical maintenance costs include irrigation water, fertiliser,

replacement plants, weeding and pest and disease management.
Periodic inspection and maintenance of the site, from the irrigation
system to clearing drains to re-tensioning of cables or repair of
loose wall fixings, will be needed. Maintenance costs may include
access costs if, for instance, an elevated work platform is required
(more information on maintenance can be found in Chapter 8).
A design contingency to cover additional costs during the
development of the design of the green wall, facade or roof
should be budgeted for, as should a construction contingency
for unexpected problems arising during installation.
Green roofs
It should be noted that it is significantly cheaper per square
metre to install a green roof on a new building than to retrofit
an existing building, as the structural load-bearing capacity can
be more easily integrated into a new project compared to
augmenting the structural capacity of an existing building.
Notwithstanding this, it is feasible to retrofit many buildings, either
by providing additional structural supports or a new floating roof
to carry the green roof.
A small green roof (30-50 m2) with reasonable access would cost
between $150 and $400 per square metre to install. This does
not include:

design fees
planning and building permits
permits for lifts and cranes
demolition or relocation of existing infrastructure on the roof
addition of specific hard infrastructure elements, such as
furniture, shade structures, decking, paving, planter boxes or
structures to support climbing or trailing plants
It also assumes that the roof has sufficient structural capacity and
does not require strengthening.
Example costs for strengthening the roof
Existing roofs may require additional strengthening work in order
to accommodate the weight of people, plants, substrate, and other
items. The following rates for strengthening an existing roof can be
used as a guide. Please note that these costs may vary according
to the issues outlined earlier under Cost considerations.
Strengthen concrete roof
slab under trafficable areas
$450 -650/m2
Strengthen a steel roof
$240/m2
Additional column supports

and foundations
$2500 to $7500 each
49
Design
Design & Planning
Example costs of individual components of

green roofs
The following rates for green roof components can be used as a
guide; however, these costs may also vary according to the issues
outlined earlier under Cost considerations.
Waterproofing
$100/m2
Drainage and protection layers
$20-30/m2
Growing substrate, plants and irrigation
$100-$500/m2
Edge restraints
$50/lin.m
Paving, decking, flooring
$200- 400/m2
Balustrading
$150-$300/lin.m
100,000L tank, pump and associated equipment
$25,000
Green walls
DIY individual wall components for retail sale may be relatively
cheap, at $160/m2 for the system and $150/m2 for the substrate,
plants and irrigation system.
A professionally installed wall will cost between $1,100 and

$2,800/m2 and will often include maintenance visits for 12 months
in the price.
Green facades
Professionally installed green facades will cost from $400/m2
upwards. DIY facades can be established more cheaply.
Example costs of individual components of
green facades
The following rates for green facade components can be used as
a guide. Please note that these costs may vary according to issues
outlined earlier under Cost considerations.
Climbing structure including

installation
$150-$350/m2
Substrate, plants and

irrigation in planter boxes
$100-150/m2
15000L tank including install
$10,000
Contingencies and other fees

In professional quotes the following contingencies are often
allowed for, in addition to the construction/installation costs
of the green roof, wall or facade:
Design contingency of 10 per cent
An amount included in a construction budget to cover additional

costs for possible design changes.
Cost escalation of 3 per cent
Anticipated changes in the cost or price of labour or materials over

a period of time.
Construction contingency of 5 per cent
An amount included in a construction budget to cover unforseen

situations/costs arising during construction/installation.
Consultant fees of ten per cent
50
Design
Design & Planning
3.6 Planning, regulations and local laws

Planning
Building
The construction of a green roof, wall or facade may require a

planning permit from the local council. At present, there are no
specific planning guidelines or requirements for green roofs, walls
and facades in Victoria, however associated building works may
require a planning permit. Such works may include, for example,
replacement of an existing roof or building new structures such as
handrails, or the supporting structures for green facades and walls.
Building permits are issued in line with the Victorian Building

Regulations. Although there are no specific requirements relating
to green roofs, walls and facades in the building regulations, a
building surveyor will need to ensure the following aspects are
satisfied before a building permit can be issued:
A planning permit will most likely be required if the building is

affected by a planning overlay such as a Heritage, Neighbourhood
Character or Design and Development overlay.
Other planning considerations include:

siting controls, such as overlooking (particularly if it is a roof that

is intended to be used as a space for people to congregate)
overshadowing
setback requirements
Where mandatory height controls apply, rooftop structures may

be prohibited. Green roofs can be used to meet private open
space requirements in private dwellings. More information about
planning schemes and the overlays in any given municipality is
available from the Planning Schemes Online website. It is also
important to speak to the local council.
compliance with siting controls in the building regulations

(for example, distance of set back from the street, avoiding
vegetation protruding onto public space)
appropriate load-bearing capacity of the structure to
accommodate proposed dead and live loads, determined in
a structural engineers report
management of waterproofing and drainage measures to
ensure the building provides a healthy environment for
its occupants
compliance with fire safety regulations, including fire-fighting
equipment and fire resistance of materials used
safety of access and emergency egress for building users,
including stairways, balustrades, number of exits, distance to
exits, and the provision of ramps for disabled access
compliance with energy efficiency performance standards
for new buildings, including evidence of the contribution
of the proposed green roof, wall or facade to these
performance standards
Local laws
Compliance with laws of the local council is required during the
building and maintenance of green roofs, walls or facades. Laws
will often address issues related to:

management and disposal of waste products, such as pruning

material generated by maintenance contractors
management of vegetation considered to be a weed or fire risk
management of overhanging vegetation on public land or
that which has a negative impact on lighting or traffic signs
drainage over public land
use of elevated working platforms or cranes on public land
during construction or maintenance
access at street level for people with a disability consider
encroachment of plants or structures into footpath space
access by emergency services do not impede the safe
egress of occupants in an emergency
It is important to make sure that vegetation is managed in a way that

complies with local laws.
51
Design & Planning
Design
3.7 Building rating schemes and planning

assessment tools
Property developers should consider the importance to them of
building sustainability ratings schemes as they commission a design
for a green roof, wall or facade. For instance:

Public buildings can obtain Green Star points for green

roofs, and other buildings have an indirect way of achieving
points under the category of land use and ecology, if the
installation is designed with native plant species and a focus
on ecological value
Under the National Australian Built Environment Rating
Scheme, green roofs, walls and facades may be able to
contribute to ratings in categories of thermal comfort and
acoustic comfort
In the green building certification program, The Living Building
Challenge, green roofs, walls and facades may be able to
contribute to building thermal performance, energy efficiency,
and water re-use objectives
NatHERS (Nationwide House Energy Rating Scheme) looks at
the energy efficiency of new residential developments, and
green roofs, walls or facades can be designed to improve
efficiency
Melbourne Waters online STORM calculator assesses the

effectiveness of water sensitive urban design (WSUD) treatment
measures on a site. This tool is often encouraged by planning
departments of local councils, because Clause 56.07 of the
Victorian Planning Provisions requires treatment of stormwater in
all new housing developments. Green roofs, walls and facades have
the potential to improve STORM ratings because they retain and/

or slow entry of run-off into the stormwater system, and green
roofs reduce the area of impervious roof surface. Local councils in
built-up urban environments are likely to respond more favourably
to building proposals that show an understanding of their water
flows onto and out of a site and have measures to manage these
responsibly.
Other rating systems sometimes applied at local council level
include the Sustainable Tools for Environmental Performance Strategy
(STEPS) tool and the Sustainable Design Scorecard (SDS) aimed
at residential and non-residential developments, respectively.
These tools can be used in the assessment of developments at
the planning permit stage as they provide an indication of the
environmental performance of a given planning application.
Although these Australian tools and rating schemes do not yet
explicitly include green roofs, walls and facades in their range
of treatment options or as a stand-alone category for points,
knowledge gained from local green roofs, walls and facades will
influence their future development. Research will be important to
ensure the thermal, biodiversity and stormwater retention benefits
of green roofs are quantified and modelled. There are examples
of international rating schemes that explicitly rate green roofs,
such as Leadership in Energy and Environmental Design (LEED)
the green building rating system developed by the United States
Green Building Council.
The Pixel Building, Queensberry Street, Carlton, created a

native grassland green roof to earn points under the Green
Star sustainable building rating tool
52
Design
Design & Planning
3.8 Selecting plants

Vegetation choices depend on the purpose and type of the green
roof, wall or facade. A successful green roof, wall or facade planting
will be based on robust, reliable species that are known, or likely,
to tolerate the areas temperatures, winds and rainfall. Look for
species that perform well in challenging locations: these may be
good candidates.
Ensure that species are not prone to pest infestation or disease.
Avoid species that are an irritant or poisonous, or that are prone
to nutrient deficiency or toxicity. Species that are weedy or that
have weed potential should be avoided.
Plant selection for green roofs and facades is highly related to
growing substrate. It is important to consider how deep the
substrate will be which, in turn, is determined by the weight
loading capacity of the roof or facade, and the project budget.
The depth of substrate influences the size of plants that can be
grown and, to some extent, how much water will be available for
the plants. Certain types of substrate will hold more or less water.
See Appendix A for further information on substrate properties
that influence plant growth.
3.8.1 Sourcing Plants

Plants can be sourced from retail nurseries, grown at home, or
ordered on contract from wholesale nurseries for large projects.
Be aware that many retail nurseries do not have experience with
green roofs, walls and facades, but requesting plants with particular
characteristics, as outlined on the following pages, should assist. For
large green roof, wall and facade projects it is important that plant
orders are placed early wholesale nurseries prefer three to six
months notice when hundreds of plants are required. It is important to insist that weed free sterile growing media is used
in propagation.
Substrate is not such a constraining factor for green walls, as these

tend to be engineered to suit the plant species chosen. Epiphytes
and lithophytes, plants that do not require soil, are often used
on green walls and can grow to mature sizes. Even species that
normally do grow in soil can be grown with no substrate through
a hydroponic system.
Plant selection must consider maintenance requirements of
different plants and their desired appearance; for instance,
manicured versus natural. Maintenance needs will be determined
by the preferred look and performance of the end result and a
willingness to meet the costs involved.
Species that are prone to grazing by possums or damage by birds
may not be suitable. Select the most robust species possible, in
keeping with aesthetic and other design aims of the project.
Planting tubestock can lower the overall cost of plant materials

for green roofs
53
Design
Design & Planning
3.8.2 Green roof plant selection

Green roofs are hostile sites. The combination of elevated temperatures, wind exposure and high light provide challenging conditions for
plant growth. Plant selection requires careful consideration of site, microclimate, substrate and maintenance factors, linked to the desired
aesthetic, functional and management outcomes for the project.
A useful way to categorise plant suitability for green roofs is required substrate depth, shown in Figure 15. See also sections on substrate in
the following chapters.
Figure 15. The substrate depth on a green roof influences the plant types that can be used
Low growing
succulents
Substrate can be as
shallow as 50150 mm
Annual to biennial
plants, herbaceous
perennials
Substrate deeper than
150 mm
Small shrubs
& turf
250 mm
Plant selection for stormwater

management
If a roof is designed to soak up water and remove contaminants in
the water during storm events, species that use water effectively
and that accumulate nutrients should be explored. Herbaceous
or shrubby species, which use more water than succulent species,
will be more effective plant choices. While it may seem counterintuitive to choose plants that have a higher water requirement
over those requiring less, water may move more effectively from
its landing on the substrate and back into the atmosphere with
herbaceous plants as the interface. In addition, higher levels of
water loss provide greater water movement and increase localised
cooling of the surrounding environment.
Plant selection for aesthetics

If aesthetics are important, then select plant species that will
provide interest throughout the year, and consider both foliage
and flowers. The period after flowering provides interest from
dried flower or seed-heads, for example, Leonotis leonurus,
Agastache rugosa, ornamental Allium species, and native species
Olearia axillaris. Planting in layers, with drought tolerant (seasonally
dormant) species is another approach. Bulbine bulbosa, Senecio
spathulatus, and other short lived species can be added in with
perennial species.
Shrubs up to 2 m
Small trees

500 mm
Best results in substrate

deeper than 1 m
Plant selection for drought tolerance

Plants that come from ecosystems with shallow soils, such as rock
outcrops, have been shown to both survive extended dry periods
and make use of the high water available after rainfall and dry out
the growing substrate. Successful species have also been shown to
re-sprout after droughts, offering an insurance policy if conditions
are particularly harsh. These species include Dianella revoluta,
Stypandra glauca and Arthropodium milleflorum.
Experience in Melbourne has shown that the succulent species
Sedum xrubrotinctum and Sedum pachyphyllum were able to
survive extreme dry conditions on the unirrigated shallow substrate
green roof at the University of Melbournes Burnley Campus
through the summer of 2008-09. Other species that failed under
the extreme conditions of 2008-09 but survived the milder 200910 and 2010-11 summers without irrigation were Sedum reflexum,
Sedum mexicanum, Sedum spurium Schorbuser Blut.
54
Design
Design & Planning
3.8.3 Types of green roof plans

Low-growing succulents
Succulents, particularly colourful sedums, dominate shallow substrate green roofs across
temperate Europe and North America. Their low growing and/or spreading habits, great
drought tolerance, seasonal flowers and contrasting foliage colours, textures and forms
make them ideal candidates for green roofs. Many will benefit from some irrigation,
particularly during drier months of the year. In projects with no, or minimal, irrigation,
thicker-leaved succulents are the most suitable. Succulents should be planted at high
density (up to 16 per square metre) to provide adequate coverage of the growing
substrate and aid shading across the surface.
Kleinia mandraliscae
Herbaceous perennials
Lychnis coronaria var. rosea
This category includes a range of non-woody plants, many with persistent roots or
underground stems (such as rhizomes and stolons, etc.) that enable the plant to regrow
and persist for many years. The most useful herbaceous perennials for Melbourne green
roofs are those originating from dryland habitats. Flowering perennials are used mainly
for display and seasonal interest, and many indigenous flowering plants used will also have
significant habitat values. Ornamental grasses and grass-like plants, especially those forming
upright tussocks, provide useful contrasts in texture and form and can be managed through
pruning to maintain their shape and habit. Some may have high water needs over summer
and large biomass forms could present a fire hazard in some locations.
Geophytes (bulbs, corms, and tubers) are another group of herbaceous perennials that
can be extremely useful, particularly for seasonal interest and display. Many of the spring
and autumn flowering geophytes are also summer dormant, making them particularly useful
drought avoiders over the warmer months of the year. Larger succulents with upright growth
habits are also useful for green roofs, although their mass over time can be considerable.
While many herbaceous perennials can be grown in substrate depths as little as 150 mm,
irrigation will be needed for long-term success at these depths. Some caution is needed in
the use of plants with vigorous rhizomes or stolons (such as some Bamboo species); they
can become excessively dominant and damage green roof profile layers.
Sisirhynchum bellum California Skies
Annual and biennial plants

A range of annual and biennial plants can be used successfully on green roofs and tend
to fall into two distinct groups. Quick growing annuals and ephemerals, particularly those
originating from dry and arid climates, can be spectacular additions to display plantings, but
will need irrigation to be sustained for longer periods. Vegetables are the other main group
of annual plants used on green roofs. These require irrigation and a substrate depth of at
least 200 mm. Careful plant selection and maintenance is needed to ensure annuals do not
become weeds on a green roof.
Brassica juncea
55
Design
Design & Planning
Turf
Some green roofs are constructed specifically to support sports turf. Careful species
selection is needed to ensure outcomes can be met: the surface and play requirements
are much more demanding than for amenity turf.
Stenotaphrum secundatum Sir Walter
Sports turf requires a designed soil or growing medium to ensure effective drainage and a
substrate depth of at least 250 mm. It also requires regular irrigation, fertilising and mowing
to maintain sward performance and health. Many facility managers seek expert advice on
the use of sports turf on green roofs to ensure design outcomes and maintenance can be
properly resourced and managed. On smaller scale green roofs, species with excessive vigour,
such as Couch Grass (Cynodon dactylon) and Kikuyu (Pennisetum clandestinum), should be
avoided: their rhizomes can be invasive and may damage waterproofing membranes.
Small shrubs
Shrubs to one metre in height are best used in substrate depths of 250 mm or more.
Small shrubs provide cover, display and habitat values, and often form the bulk of plantings
used on green roofs with deep substrates. Increasing the substrate depth and irrigation will
also increase the range of plants that can be used successfully. Excessively vigorous species
should be avoided unless there will be sufficient maintenance to manage their growth, some
low hedging plants could be in this category.
Cotoneaster dammeri
Shrubs
Shrubs up to two metres high can be used where substrate depths are at least 600 mm.
They provide screening, space definition, ground coverage and seasonal flowers. Like any
plant group, shrubs require careful selection and consideration of their maintenance needs.
Plants with dense, upright habits should only be used where there is minimal wind exposure
and/or significant protection can be afforded to support the canopy and prevent wind
forces. Hedges and screening shrubs will require regular maintenance, including pruning
and removal of biomass off the roof.
Juniperus sabina
Trees
Malus ioensis Plena
While many small trees (to five metres) can be successfully grown on substrate depths
of 600 mm, depths of 1,000 mm or greater will ensure the best outcomes are achieved.
Trees are dominant elements in any landscape, and on a green roof trees will generally
be stunted in height and spread, when compared to those planted at ground level. The
greater the roof exposure and overall site hostility, the more important tree selection
becomes. Trees with sparse canopies, flexible stems and high tolerance to heat are best in
areas of high wind exposure, although some form of anchorage will always be needed to
manage them successfully.
56
Design
Design & Planning
Table 7. Suitable plants for green roofs in Victoria

Highlighted text indicates native species. Provided as a guide only, and should not be considered as an exhaustive list or suitable for all sites.
Low growing succulents

Type
Examples
Small and/or thin

leaves
Crassula multicava
Sedum mexicanum, S. reflexum, S. sexangulare
Thick leaves and/

or stems
Carpobrotus rossii, C. modestus

Disphyma clavellatum
Carpobrotus edulis
Cotyledon orbiculata
Crassula tetragona
Kleinia mandraliscae, K. repens
Lampranthus deltoides
Mesembryanthemum echinatum, M. lehmanii, M.

floribundum
Sedum nussbaumerianum
Sedum pachyphyllum
Sedum xrubrotinctum
xGraptosedum Bert Swanwick
xSedeveria Pats Pink
Herbaceous perennials
Type
Examples
Upright flowering
perennials
Brachyscome ciliaris, B. multifida

Calocephalus citreus
Calotis cuneifolia
Chrysocephalum apiculatum, C. semipapposum
Leptorhynchos tenuifolius
Podolepis jaceoides
Rhodanthe anthemoides
Veronica gracilis,V. perfoliata
Vittadinia cuneata
Wahlenbergia communis,W. stricta

Xerochrysum bracteatum
Achillea cultivars
Agastache species and cultivars
Euphorbia rigida, E. myrsinites
Nepeta cultivars
Pelargonium sidoides
Hylotelephium Matrona, H. Autumn Joy
Hylotelephium cauticola Ruby Glow
S. nemorosa cultivars
Low, spreading
ground covers
Dichondra repens
Einadia nutans
Eutaxia microphylla
Grevillea lanigera
Kennedia prostrata
Myoporum parvifolium
Senecio spathulatus
Viola hederacea
Aptenia cordifolia
Cerastium tomentosum
Convolvulus sabatius
Glechoma hederacea
Tradescantia pallida Purpurea
Thymus pseudolanuginosus, T. serpyllum
Geophytes (bulbs,
corms, tubers, etc)
Arthropodium milleflorum
Bulbine bulbosa, B. crassa, B. vagans
Pelargonium rodneyanum
Allium species and cultivars

Tulbaghia violacea
Larger succulents
(upright and
rosette forms)
Aeonium arboreum
Aeonium haworthii
Aloe mitriformis
Aloe Gemini
Aloe brevifolia
Crassula falcata, C. ovata Blue Bird, C. tetragona

Echeveria ximbricata
Echeveria cultivars
Hesperaloe parviflora
Yucca desmetiana
57
Design
Design & Planning
Herbaceous perennials (continued)

Type
Examples
Grasses
Austrodanthonia caespitosa, A. setacea

Austrostipa scabra
Chloris truncata
Deyeuxia quadriseta
Dichelachne crinita
Orthrosanthus multiflorus
Helictotrichon sempervirens
Miscanthus cultivars
Flowering plants
with grass-like
foliage
Anigozanthos cultivars
Conostylis species and cultivars
D. caerulea, Dianella revoluta, D. tasmanica species
and cultivars
Ficinia nodosa
Lomandra micrantha, L. multifida and cultivars
Poa hiemata
Stypandra glauca
Themeda triandra
Armeria maritima
Sisirhynchum cultivars
Iris unguicularis
Liriope species and cultivars
Ophiopogon japonicus
Annual and biennial plants

Type
Examples
Plants for floral

display
Calandrinia eremaea, C. polyandra

Calendula officinalis
Tagetes patula, T. erecta

Zinnia elegans
Allium schoenoprasum
Culinary herbs
and vegetables
Ocimum basilicum
Petroselinum crispum
Salvia officinalis, S. Greek Skies
Thymus vulgaris
Origanum vulgare
With a suitable substrate and irrigation, most

vegetables that can be grown in containers should
succeed on a green roof
Turf
Type
Examples
Amenity turf
Zoysia macrantha
Stenotaphrum secundatum
Zoysia species
Festuca arundinacea
Festuca rubra Commutata

Poa pratensis
Lolium perenne
Sports turf
Cynodon dactylon
Pennisetum clandestinum
Digitaria didactyla
Lolium perenne
58
Design
Design & Planning
Shrubs
Type
Examples
Small shrubs
(to 1 m)
Acacia amblygona
Correa glabra, C. reflexa, C. decumbens and cultivars
Olearia axillaris
Plectranthus argentatus
Buxus sempervirens and B. microphylla species and
cultivars
Cotoneaster dammeri
Erysimum xcherei
Gaura lindheimeri species and cultivars
Helichrysum italicum
Lavandula species and cultivars
Nandina domestica Nana
Plectranthus ciliatus, P. parviflorus
Salvia chamaedryoides, S. microphylla species and
cultivars
Santolina magonica, S. chamaecyparissus, S.
neapolitana cultivars
Teucrium marum
Shrubs (to 2 m)
Callistemon Little John

Correa alba
Eremophila debilis
Grevillea obtusifolia, G. rosmarinifolia
Lasiopetalum behrii
Melaleuca incana
Westringia species and cultivars
Cistus species and hybrids
Escallonia cultivars
Juniperus horizontalis, J. sabina
Leonotis leonurus
Nandina domestica
Pittosporum tobira
Raphiolepis umbellata, R. indica species and cultivars
Rosmarinus species and cultivars
Viburnum tinus
Small trees (to 5 m)

Type
Examples
Trees
Acacia cognata cultivars, A. pendula, A. stenophylla

Brachychiton rupestris
Eucalyptus caesia Silver Princess, E. dolichorhyncha,
E. macrocarpa, E. pauciflora
Ficus microcarpa var. hillii
Tristaniopsis laurina
Arbutus species and hybrids
Cercis siliquastrum
Citrus limon
Cussonia paniculata
Jacaranda mimosifolia
Lagerstroemia indica xfauerii cultivars
Malus ioensis Plena
Metrosideros excelsa
Pyrus salicifolia
Quercus ilex, Q. suber, Q. coccifera
Geijera parviflora
Ulmus parvifolia
Olea europaea Tolleys Upright or Swan Hill
Laurus nobilis
Tree-like forms
Dracaena draco
Yucca gigantea
59
Design
Design & Planning
3.8.4 Green wall plant selection

Depending on the scale of the wall, plantings can range from ground
covers to larger herbaceous species, shrubs and even small trees.
Table 8. Suitable plants for green walls in Victoria
Shrubs
Correa cultivars
Ficus species
Metrosideros excelsa Nana
The selection of species will also depend on the climatic conditions

on-site. Consider the level of natural or artificial light available.
(Be aware that plant selection will require an understanding of
photosynthetically active radiation, the type of light that a plant
responds to, rather than simply a measure of how the human eye
perceives brightness). Select very shade tolerant species to suit the
lowest light conditions. In highly exposed locations, select robust
species that can tolerate sun and wind. Look for species that have
shallow, fibrous root systems to promote strong anchorage in the
limited volume of growing medium available. Recognise that the
tops, corners and sides of the wall will have greater wind exposure.
Investigate species that thrive in exposed conditions, such as coastal
cliffs or inland rocky outcrops.
Evergreen
herbaceous
perennials
Spathiphyllum cultivars
Philodendron Winterbourn and
Xanadu
Monstera species
Liriope species and cultivars
Schleffera species
Viola species
Erigeron karvinskianus
Chlorophytum comosum
Peperomia species
Plectranthus species
Rhipsalis species
Bromeliad species
Orchid species
Herbaceous
ground covers
Epipremnum species
Plectranthus ciliatus
Larger plants may grow to shade others, so this must also be

considered in the placement of species. External green walls are
often exposed to strong and frequent wind. Vigorous growth
increases maintenance requirements and slow growing plants
are often preferred. However, vigorous species can be used to
create protected niches for the inclusion of sensitive species in
high exposure areas. This can help provide light or shade for other
species, wind protection or humidity conservation. Consideration
of where each species will be placed in relation to others (the
array of plants) helps develop a working artificial ecology on the
wall. Understanding how the ecology will morph as the plants
mature is important, as niches will evolve beneath, next to and
above certain species.
Ferns
Asplenium species
Blechnum species
Davallia pyxidata
Humata tyermanii
Nephrolepis species
Grass-like
foliage forms
Acorus gramineus cultivars

Bulbine species
Ficinia nodosa
Dianella species and cultivars
Dietes species
Lomandra species and cultivars
Ophiopogon japonicus
Lilies & irises
Arthropodium cirrhatum Te Puna

and Parnel
Arthropodium species and cultivars
Neomarica gracilis
Patersonia occidentalis
Plant selection should firstly consider the desired outcomes of

the green wall. Certain plants will be better for aesthetic and
landscape design values, drought tolerance, water purifying, air
filtering or habitat provision. It is important to realise that plant
growth form, sun and shade exposure as well as wind exposure,
is notably different on vertical surfaces compared to a roof or
at ground level. Obtaining specialised advice and visiting existing
green walls will improve understanding of which species will be
best suited.
Plant selection must be matched to the particular green wall system

and technology that is being installed. Not all species will grow
well in each system. Some systems might cater well for terrestrial
plant species (and need an appropriate growing substrate); others
have an irrigation/fertigation or growing media system that favours
epiphytic/lithophytic species (plants that do not require soil for
growing and can exist on branches or rock surfaces).
Water requirements can be minimised by selecting species that
are low water users. Recognise that more water may be available
toward the base of a green wall system, so species should be
selected and positioned on the wall with moisture gradients in
mind. If the system recycles water, species selection may have to
cater for elevated salt levels and amended pH levels.
60
Design
Design & Planning
3.8.5 Green facade plant selection

Plant selection for green facades is strongly influenced by the mode
or method of climbing plant attachment. Most climbing plants
attach themselves to a surface or structure in one of two ways
(see Figure 16):

Self-clinging attachment through adhesive suckers, disks

or adventitious roots. These climbers then form a selfsupporting vegetation layer on a solid wall or surface.
Twining and tendrils attachment by twining stems or by
hooking and clasping tendrils (modified leaf/stem organs).
These climbers require a specialised support system and
can produce both upward and cascading (or trailing) stems.
Another group of climbing plants have a scrambling habit and

are known as scandent shrubs. These have no direct means of
attachment and need to be tied and managed onto the structure
that supports them. They may be vigorous and woody in their
growth habit, which can make them difficult to be sustained on
a structure without significant pruning and maintenance (such as
Bouganvillea glabra).
Self-clinging climbers create green facades that can provide effective
and long-term cover but may not be suited for buildings where
the surface fabric is in poor repair. Many self-clinging climbers
will mark a wall surface through their attachment, however this
is rarely seen because of the foliage cover. Excessively vigorous
species such as Common Ivy (Hedera helix) should be avoided
and regular pruning will always be necessary to maintain suitable
plant growth, form and size.
Twining climbers require a support system, such as cable or trellis,

to support their growth habit. These supports may be attached
to the building, or mounted independently. Plant selection needs
to consider the available space for plant growth as the distance
between the wall and the support structure will impact on plant
performance and climate control.
Climatic factors
Species tolerant of low light are required for deeply shaded urban
canyons while high light tolerance is needed in exposed and
elevated settings. Generally, direct sunlight is considered to be four
hours of sun per day and most species will require at least some
direct sunlight to grow.
Facades can be established in areas of full shade, but the range
of species that will grow in these conditions is limited. Facades
at high elevation, in coastal areas or urban street canyons can be
exposed to strong and frequent wind. Some plant species, twining
climbers in particular, are more tolerant of wind and more mature
plants tend to be more resilient in these environments. Selfclinging facades may be pulled away from the wall in very windy
conditions. Small-leafed species with strongly attached foliage may
be more suitable on sites prone to strong blasts of wind: large
foliage may be stripped or shredded in these conditions.
Figure 16. Climbing plants used on green facades have different modes of attachment
Self-clinging plants
attach directly to
the building facade
Twining and tendril

climbers can be grown
to cover a building
facade on a cable or
trellis support
61
Design
Design & Planning
Long-term maintenance
The plants lifecycle and growth rate will affect the time it takes for
the facade to establish and the amount of ongoing maintenance
required. Consider the mature size of the species as well as the
level of foliage coverage required. Many climbing species exhibit
early rapid growth but slower mature growth rates. Some green
facade plants, such as Creeping Fig (Ficus pumila), require rejuvenation
pruning to ensure juvenile foliage is maintained. With this species,
adult foliage grows horizontally, does not attach directly to the
building and creates a deeper, denser canopy of woody stems.
While this may provide effective shading and create an insulating
layer of air between the foliage and the building, it is inherently
unstable because this canopy is not directly attached to the building.
Woody climbers need careful selection as maintenance needs often
increase over time, as stems grow larger and thicker and the plant
increases in size: for example, Wisteria sinensis and Vitis vinifera.
Climbing plant species ideal for screening will have multiple

features including:

retention of lower foliage

high shoot density
pendulous leading shoots
tolerance of and recovery from severe pruning

(rejuvenation)
longevity
reliable growth rate
These features contribute to the production of consistent and

uniform vegetative cover.
In their natural habitat, many climbing plants grow upwards
towards the light, by twining or scrambling, and over time, they
lose foliage cover at their base. Such species may be unsuitable as
screening plants in the long term, if they do not respond to hard
(rejuvenation) pruning to encourage new basal shoots, such as
Pandorea jasminoides (Bower Vine).
The following table indicates some common climbing plants used
in Victoria, how they attach, their ability to cover an area of facade
how well they screen (high to low cover) and how fast they
grow (this indicates how much maintenance they require) and
their light tolerance. Average in the table indicates that they are
not known to be particularly needy of high light nor particularly
tolerant of low light. Note that the mature size will be affected by
the soil volume available.
Table 9. Suitable plants for green facades in Victoria

Species
Type
Screening and Growth Rate
Light Tolerance
Akebia quinata
Twining
Medium cover and growth rate
Average
Aphanopetalum resinosum
Twining
Average
Cissus antarctica
Tendril
High cover and growth rate
Tolerates low light
Clematis aristata
Twining
Tolerates low light
Clematis armandii
Twining
Low cover and growth rate
Average
Clematis montana*
Twining
Low cover and growth rate
Average
Distichtus buccinatoria
Tendril
High cover and medium growth rate
Requires high light
Ficus pumila
Self-clinger
Requires high light
Hibbertia scandens
Twining
Requires high light
Muehlenbeckia complexa
Twining
Average
Kennedia rubicunda
Twining
Medium cover and high growth rate
Requires high light
Pandorea pandorana
Twining
Average
Pandorea jasminoides
Twining
Average
Parthenocissus quinquefolia*
Self-clinger
Average
Parthenocissus tricuspidata*
Self-clinger
Requires high light
Podranea ricasoliana
Scandent shrub
Requires high light
Vitis vinifera*
Tendril
Requires high light
Trachelospermum jasminoides
Twining
Average
Wisteria sinensis
Twining
Low cover and high growth rate
Requires high light
*deciduous
62
Design
Design & Planning
3.9 Designing for plant establishment

Good plant establishment is critical for the long-term health and performance of plantings in green roofs, walls and facades. In the design
stage this includes consideration of multiple factors, including:
Use of high quality

planting stock
Stock that is too advanced or has overgrown its containers has high water
needs and can be slow to establish on a site. Planting stock should be of an
appropriate size to achieve the aims of the project, in terms of growth rate
and coverage. It should also be completely free of weeds, pests and disease.
Plant production in a
high quality growing
medium
In some cases using a medium with similar physical properties to the final
growing substrate will assist in promoting plant growth.
Working in with
seasonal conditions
In most situations planting is best completed between autumn and early

spring. This will assist plant establishment and growth, well before the
warmer and drier conditions of summer.
Establishment irrigation
Allowance should be made for suitable irrigation, usually for a minimum of

six months, to avoid moisture stress and to promote plant growth across
the site.
Weed control
During establishment, weeds will compete vigorously with designed plantings

on a green roof, wall or facade. Weeds must be controlled until the plantings
achieve the desired growth rates and/or coverage.
Further information about vegetation can be found in Chapters 5, 6 and 7.
Plants will often establish best on-site, and should not be planted
when they are large as they will grow to cover the site over time
High quality plants should be sourced, ideally grown in a medium with

similar properties to the growing substrate they will be planted into
63
Building & Installation - General Advice
Advice
Construction of a green roof, Docklands. Image: ASPECT Studios
4. Building &
installation
general advice
This chapter provides general advice about building green roofs, walls and
facades, including occupational health and safety, insurance considerations and
what to expect at project completion on a large-scale job which has a project
manager and several consultants.
64
Advice
4.1 Occupational Health and Safety

As for all construction work, the construction (and maintenance) of green roofs, walls and facades is subject to the Victorian
Occupational Health and Safety Act 2004. This Act governs all Victorian OH&S laws and codes of practice and sets out the key principles,
duties and rights in relation to OH&S. The hierarchy of regulation in Victoria is shown in the diagram below.
Figure 17. Occupational Health and Safety legislative framework in Victoria
Victorian Occupational Health and Safety Act 2004

Occupational Health and Safety Regulations 2007
Compliance Codes
Worksafe Victoria Positions
Guidance materials available from WorkSafe Victoria inform

duty holders on how to comply with Victorian OH&S legislation.
Consultants can also provide advice on ensuring OH&S
requirements are met.
Note that National Workplace Health and Safety codes and
guidance materials have no legal status in Victoria.
High-risk construction work

Some construction projects involve high-risk construction work
and additional regulations govern management and procedures in
such cases. High-risk construction work is of particular relevance
to the design, construction and installation of green roofs, walls
and facades as it is likely to involve work:

where there is a risk of a person falling more than two metres

on or near electrical installations or services, for example, the
possibility of drilling into a wall containing live electrical wiring
at a workplace where there is any movement of powered
mobile plant, for example, working in an area of a
construction site with moving skid steer loaders, telehandlers,
backhoes, mobile cranes or trucks
OHS Compliance Framework
WorkSafe Victoria Policies
be moved to and from site. Secure storage and safe handling

of materials on-site may be needed. For safety reasons, a roof
must not be used for materials storage when a green roof is
being constructed, as it is a building site and must be managed
for weight, access, security of materials and safe movement of
personnel.
Working at heights
The design and installation of all green roofs and many green
walls and facades involves work at heights. The associated risks
and responsibilities must be managed through a combination
of training and safety features on the site including the use of
barricades, railings, or other fall arrest systems, such as ropes and
harnesses.
Consult the WorkSafe Victoria Compliance Code Preventing Falls
in General Construction with regard to specific OH&S issues
associated with working at heights and management solutions.
Wherever possible, the risks and hazards of working at heights
should be removed or reduced and the design team must
consider these as part of project planning.
Materials handling and storage
Safety in Design legislation
As on any building site, the materials used to construct a green

roof, wall or facade should be delivered in a timely way to
meet construction schedules. Consideration must be given to
where materials will be unloaded and stored and how they will
A Safety in Design risk assessment or workshop should be

undertaken with the design and construction team/s to identify
risks and determine the actions necessary to remove or reduce
the likelihood of occurrence and severity of these risks.
65
Advice
4.2 Insurance and system warranties

The scale, complexity and overall cost of a green roof, wall or
facade will determine whether insurance and warranties are
relevant. Almost all professionally-installed projects will include
them; smaller, DIY projects may not.
Until the local industry is further developed, it may be beneficial
to consider insurance companies with a global reach that
gives them relevant understanding and experience. Commercial
insurer FM Global provides useful specifications for green roof
design, installation and maintenance that can be used as a risk
management tool during design and planning.
The warranty for a green roof, wall or facade will be straightforward
if an established installation company, or a contractor licensed by that
company, installs a proprietary system. Under these circumstances,
the parent company should provide a warranty against failure of
any or all of the components. Custom-built green roofs, walls or
facades, with mix-and-match components, or multiple providers,
may not be as straightforward to warrant or insure.
Waterproofing is more likely to be warranted separately if it is

installed by a third party. However, the company supplying and/
or installing the waterproofing may not take responsibility for
breaches of the membrane that occur after it is certified as
watertight, if they have no ongoing involvement with the project.
Ensure there is clarity around the warranty conditions.
The client usually has the option to negotiate a defects liability
period with the contractor. The contractor will be responsible for
repair of defects that appear within an agreed period of time after
project completion and may have responsibility for defective work
beyond the product warranty period. Warranties may be waived if
a DIY approach is undertaken with the product.
4.3 Project completion

Contractors and sub-contractors must provide necessary
certifications at the completion of their work. At handover, the
project manager will provide documentation of all necessary
inspections and relevant certifications to the building owner.
These should include:

warranty on waterproofing
drawing showing as built planting (the actual planting may
have varied from the design drawings)
certificate of completion from a registered building inspector
certificate of electrical safety from a licensed electrician
(if relevant)
certificate of occupancy (if relevant) from a building
inspector/local council this will relate mainly to safety and
access requirements, including step heights and access points
Operational manuals must be handed over to the owners and/

or contractors who will be engaged in operation or maintenance
of the site. This must include the setting of an agreed time for any
initial or ongoing training in the operation of systems installed on
the site. Provision of funds for such training should be included as
a contingency item in the budget during the design phase.
Maintenance or operational manuals may include:

a planting maintenance plan

an irrigation operations manual
schedules for cyclical maintenance
Maintenance is discussed in more detail in Chapter 8.
66
Building & Installation - Green Roofs
Roofs
Green roof at the Museum of Old and New Art, Hobart. Image: Pad Creations
5. Building &
installation
green roofs
Once the planning and design stages of a green roof are complete, well-planned
construction can deliver the project objectives. This chapter provides specific
information about how to construct a green roof.
67
Roofs
Constructing green roofs

Green roofs are built up as a series of layers, with each performing
a specific function. The most typical build-up is shown below and
includes:

the roof structure (roof deck)

waterproofing layer
protection layers (including the option of a protection mat
and/or root barrier layer)
drainage layer
filter sheet
growing substrate
vegetation
The role of each of these components is outlined in the

following pages. This chapter also covers other elements that
may be incorporated into a green roof system, or are relevant to
construction of a green roof, such as:

leak detection systems

thermal insulation
irrigation
greening in windy environments or on a pitched roof
hard landscaping elements
Specialists in green roof design and installation can provide

advice on the most suitable system and the most appropriate
construction approach.
Figure 18. Layers of green
Vegetation Layer
Growing Substrate
Filter Sheet
Drainage Layer
Protection Mat
Root Barrier
Waterproofing
Roof Deck
A green roof contains plants that are grown in a layer of substrate varying in depth from a few centimetres to well over a metre. The growing
substrate is usually composed of a high proportion of mineral particles with a long lifespan, with a small proportion of organic matter. A filter sheet
retains the substrate and prevents washout into the underlying drainage layer. A protection mat and a root barrier may be installed to prevent
damage to the underlying waterproofing membrane that covers the roof deck.
68
Roofs
5.1 Roof deck

Green roofs can be installed on roofs made of concrete, timber,
sheet metal (usually clip-lock, or corrugated galvanised steel) and
a range of other materials. However, it may be difficult to obtain
insurance for green roofs installed on roof decks made from
materials other than structural concrete or metal. Green roofs
are most commonly installed on concrete roof decks because of
structural integrity, ease of design, durability and amenity when
complete. See Chapter 5.12 Slopes and wind protection for
specific considerations relating to pitched roofs.
Greening a tiled roof requires special treatment. A green roof
cannot be installed directly on a tiled roof. If the building has
adequate load capacity, or if structural reinforcement and a support
system can be incorporated into the design, a green roof may be
constructed as a self-contained waterproof module that sits above
the existing roof. Drainage from the green roof must connect
directly into the lower level roof drainage system. It may be more
economical to replace the roof to make it suitable for a green roof.
The components installed on the roof deck will be either looselaid over the roof surface or installed as modules that connect
together to form a continuous effect. Individual containers that
are separately placed on a roof deck are considered a roof garden
rather than a green roof, and because they do not cover a significant
proportion of the roof they do not provide most of the benefits
associated with green roofs.
It may be necessary to remove or relocate existing infrastructure
on roof decks, or the green roof can be built around the equipment.
Roof decks can be flat or pitched, and they are commonly made of metal or concrete
69
Roofs
5.2 Waterproofing
A watertight roof is critical to successful green roof construction.
While some roofs are intrinsically waterproof when built, most
will require some form of treatment to prevent water entry into
the building. Waterproofing treatment must provide a strong but
flexible layer that allows expansion under physical or thermal
movements of the building structure, without compromising
watertightness. Vegetation generally should not be installed over
areas such as expansion joints, where regular inspection of the
waterproofing will be necessary.
Advice should be sought from a specialist waterproofing
manufacturer to find the most suitable type of waterproofing
treatment for the roof structure and the proposed green roof
design. The manufacturing and installation of waterproofing
membranes should comply with Australian Standards (see
Chapter 6.2 for more information).
In Australia, waterproofing is likely to be installed by a third party
waterproofing contractor. The involvement of an independent
contractor means that a clear agreement between all parties
must be established for responsibility of the waterproofing
membrane once it has been installed and certified as watertight.
An independent leak detection specialist should test the
waterproofing after its installation, and again after the green roof
build-up is installed, prior to handover (see also Chapter 4.3).
The following tables contrast the two major types of
waterproofing liquid applied treatments and preformed sheets:

Liquid applied treatments can be composed of bitumen

emulsions, modified bitumen, polymer cement systems,
polyurethane, polyurethane modified acrylic, acrylic or twopart polyurethane hybrid elastomers that require mixing
prior to application.
Preformed sheets are asphalt-based or comprised of
thermosetting polymers or thermoplastic polymers.
Preformed waterproofing may suit green roofs with gentle slopes

and large uninterrupted areas. A green roof with many fixings
onto the roof deck or penetrations, such as for lighting, power or
ventilation, may be more suited to liquid applied waterproofing
that is sprayed on or rolled on to form a cohesive single layer.
Waterproofing membranes must be protected from physical
and chemical damage. This includes cuts and tears, the action of
invasive roots and rhizomes, and exposure to the elements. All
membranes will become brittle over time, and this is accelerated
by exposure to cold, heat and UV rays from sunlight. A green
roof will shield the membrane from damage and can significantly
lengthen its life. Some preformed membranes have a surface
coating that provides additional protection.
Ensure that the waterproofing material is certified root resistant,
suitable for the substrate, and installed by experienced, trained and
certified professionals.
Root resistance may be built into waterproofing membranes
either by the addition of root-inhibiting chemical treatments,
or because the composition of the membrane provides an
impenetrable barrier to root growth. Root resistant waterproofing
is quicker to install than separate waterproofing and root barrier
layers, but can be more costly. Examples include certain types of
ethylene propylene diene monomer thermosetting, thermoplastic
PVC and thermoplastic polyolefin membranes; however, the rootresistance of a product must be confirmed with the manufacturer,
with certification provided.
70
Roofs
Table 10. Common waterproofing treatments

Liquid applied waterproofing treatments
Suitability
Advantages
Complex designs with

many upstands1, corners
or curves
Roofs where access

for sheet installation
is difficult
Disadvantages
Seamless
Often trafficable
Flexible and capable of elongation
Easy to apply
Tolerant of some degree of surface
imperfection
Easily repaired by re-application over
breaches
Bonded to the roof
Pin-holes may develop on poorly prepared

roof surfaces2
Solvent-based treatments become brittle
over time and with exposure to sunlight and
high temperatures
Root resistance
Not easy to ensure uniformity of thickness
Not recommended for use in permanently
wet conditions, as
they absorb moisture and soften over time
Preformed waterproofing sheets

Membrane
composition
Application
methods
Advantages

Loose-laid
Asphalt-based
Fully bonded
torch-down
Partly bonded

Thermo-plastic
Fully bonded

Thermo-setting
Fully bonded

Loose-laid membranes quick to install

compared to bonded.
Fully bonded more resistant to wind
uplift than partly bonded.
Fully bonded recommended by some
green roof installers and lower risk of
uplift makes insurance easier to obtain
Easier to locate leaks with precision
with fully bonded membranes.
More resistant to wind uplift than
loose-laid.
UV stable and weatherproof
Seams can be welded with heat or
solvent3; or heat only4
Bonding of membrane to the roof with
heat, solvent, water-based adhesive, or
tape reduces risk of wind uplift
PVC membranes are breathable, and
well suited for bonding to the roof
deck with glue or tape adhesives
PVC, thermoplastic polyolefin, ethylene
vinyl acetate and ethylene butyl acrylate
membranes are likely to be classified
as root resistant: check manufacturers
specifications
Mechanical fastening to the roof deck
may be suitable for some applications
Ethylene propylene diene monomer
(EPDM) and Butanoyl membranes
are likely to be classified as root
resistant: check manufacturers
specifications
UV stable and weatherproof: long lifespan
Bonding with glue or adhesive tape
reduces risk of wind uplift
Disadvantages

Loose-laid not recommended if high

risk of wind uplift
Soft structure means membranes
are usually not trafficable, UV
resistant or root-resistant.
Prone to failure and root
penetration along seams due to
softness of composition
Installation requires a high degree of
skill to ensure high quality detailing
of seams and around upstands1.
Become brittle over time through
exposure to sunlight, heat and cold.
With classes of membrane other

than PVC, condensation of moisture
may soften glue or adhesive tapes
used to attach membrane to the
roof deck, increasing risk of wind
uplift
Condensation of moisture may

soften glue or adhesive tapes used to
bond waterproofing to the roof deck
Carbon content of EPDM/Butynol
membranes makes them intrinsically
electrically conductive and therefore
unsuitable for electronic leak
detection
Upstands are structural penetrations from the roof such as vent pipes that will need to have the waterproofing layer brought up (dressed up) around
them to terminate above the level of the substrate.
2
Note that the waterproofing consultant must certify that the roof is fit to receive the membrane prior to installation.
3
Thermoplastic polymers composed of chlorinated polyethylene, polyvinyl chloride (PVC), thermoplastic polyolefin, ethylene vinyl acetate and ethylene
butyl acrylate.
4
Thermoplastic polymers composed of ketone ethylene ester.
1
71
Roofs
5.3 Protection layers

Root barrier
Protection mat
Root barriers are often used in green roofs to provide some

protection to the waterproofing from invasive stolons, rhizomes
and from woody roots from trees and shrubs. The most common
root barriers used are thin polyethylene sheets, laid over the
waterproofing membrane. These may not be required if the
waterproof membrane is certified as root-resistant. Thicker,
welded root barriers will be needed for green roofs involving
trees, bamboo or other vigorous, spreading grasses.
Protection mats or boards are used to protect the waterproof

membrane from damage following installation. The most common
materials used are water-permeable, hard wearing and dense
synthetic fibres, polyester and polypropylene.
It is important to check the compatibility of the product with

bitumen and polystyrene, especially where there is direct contact
with a bitumen-based waterproofing or polystyrene insulation. The
root barrier must also be resistant to the humic acids produced
when plants decompose.
Separation sheets are sometimes installed between the
waterproofing and root barrier to provide additional protection
and separate materials that are not compatible. These are typically
HDPE sheets laid directly on the waterproofing.
Plant roots can be very destructive, as shown by this image of tree roots
causing severe cracks in bitumen paving. A root barrier on a green roof
can protect the underlying layers
Protection matting is installed directly on the waterproofing layer

(for root-resistant membranes) or atop the installed root barrier
layer, providing further (uncertified) protection against root
penetration and doubling as a separation sheet. The protection
matting may provide some noise-absorbing capability. It can add
to water retention on the roof, although the amount varies (from
3 l/m2 to 12 l/ m2) and is only really useful on slopes below 15
degrees. A range of different products are available, reflecting
the required functions, and apart from the material itself vary
according to thickness (3 mm to 20 mm), fibre density and mass
(320 g/m2 to 1500 g/m2).
Protection mat sheeting should be installed with overlaps of 100
mm and some products have rubber backing that requires gluing
in situ. The product should extend 150 mm above the finished
surface of all upstands (such as vent pipes, chimneys and other
roof penetrations) to ensure complete roof protection.
A protection mat is laid to protect the waterproofing layer on a green roof
72
Roofs
5.4 Drainage layer
5.5 Filter sheet
Good drainage is critical for green roofs and ensures that large
amounts of water are not retained on the roof, compromising
both the structural integrity of the building and plant health
through waterlogging and oxygen-depleted substrates. Sub-surface
run-off must drain efficiently from the substrate, into the drainage
layer, off the roof surface, and into drains to the stormwater or
rainwater collection. The growing substrate must be kept separate
from the drainage layer with a filter sheet.
A filter sheet acts to retain the growing substrate, by preventing

wash-through of the substrate particles into the underlying layers,
and to prevent clogging of holes in the drainage layer. Filter fabric
is sometimes referred to as geotextile fabric.
Older green roofs often used a permeable layer of rock aggregate

(such as scoria or gravel) for drainage. The clay and silt content
of materials used in a rock aggregate drainage layer should be
10 per cent by mass. The rock aggregate should also have a
suitable pH and be low in soluble salts to ensure plant growth is
not adversely affected. This form of drainage is heavy and does
not allow for air pruning of roots, which is now achieved with
plastic drainage cells. However, in some situations, rock aggregate
drainage does a better job controlling peak flow.
On modern, lightweight, green roofs, plastic drainage sheets
or boards are the preferred drainage materials. Plastic drainage
layers may be rigid, open mesh structures that allow unrestricted
drainage of water, or they may have a cup-style, egg carton design
that enables water to be stored at the base of the profile (see
image below). The advantage of the latter is that water can be
stored and used later by the plant. The volume of water that can
be stored varies with each product and the size and packing
density of the cells.
Considerations in the selection and use of filter sheets include:

the expected flow rate of water as it drains through

the system
substrate type if components of the substrate have sharp
edges, the filter sheet should be strong
vegetation type the filter sheet must allow penetration of
roots, and certain roots will be more or less aggressive (for
example, herbs versus trees roots)
The filter sheet can be either a woven or non-woven material.

A non-woven material is preferable as it is more resistant to root
penetration and can sometimes be used as a root barrier system.
The filter sheet is not weatherproof and should not be exposed
to sunlight for any length of time, and it should therefore be laid
immediately prior to the installation of growing substrate. At
boundaries or edges of planting beds, the filter sheet should be
installed with upturns to at least the same height as the top of the
growing substrate (see image below).
Drainage is installed as a continuous layer over the entire surface

of the green roof. Cup-style drainage sheets should be overlapped
to eliminate the possibility of gaps being created between sheets.
Other plastic drainage types should have adjacent sheets butted
together. Very rigid drainage layers should be installed in trafficable
areas of the green roof to avoid compression of the layer.
An eggcup-shaped drainage layer retains some water. Image: KHD

Landscaping Engineering Solutions
A layer of filter sheet will prevent substrate dropping into the drainage
layer. Enough filter sheet is set down over the roof so that at the
vertical edges of the planting beds the sheet will be the same height
as the substrate
73
Roofs
5.6 Growing substrate

The growing substrate supplies water and nutrients to plant roots,
ensures gas exchange at the roots and provides anchorage to
support plants.
Growing substrates for green roofs are typically composed of
a mix of inorganic (mineral) and organic components. They can
include scoria, ash, pumice, sand, coir, pine bark, porous, chemically
inert foams and even recycled materials such as crushed bricks,
and roof tiles. Organic matter is usually kept to a low proportion
(typically 20 per cent or less) because it has a relatively short
lifespan, degrading and slumping over time, and may become
water repellent and difficult to re-wet if it dries out. The physical
and chemical properties of the substrate mix, together with
its depth and total volume, influences what vegetation can be
supported on the green roof.
A substrate should:

have a known saturated weight loading, that forms part of

the structural load capacity of the roof; this is referred to as
the saturated bulk density
drain freely, to reduce waterlogging and prevent inundation
during heavy rain, but also retain adequate water to sustain
plant growth outside of heavy rain events
be stable over time, usually achieved by using a high
proportion of mineral components and a lower proportion
of organic components.
Soil is generally not used on green roofs, as its properties will

be less well known compared to an engineered substrate, and
therefore its longevity and suitability is harder to judge. Also,
silt particles from soil can clog filter sheets and cause drainage
problems.
Installers of green roof systems will be able to arrange the supply
of a suitable substrate mix. Appendix A provides more information
on substrate characteristics.
Transport and installation of growing substrates requires
consideration in the pre-construction planning process. Most can
be installed by either lifting bulker bags by crane or blowing from
a truck-mounted hopper, although each project will have its own
specific considerations. See the Substrate Installation box following
for more on installation.
A range of mineral and sheet mulches can be used successfully
on green roofs but need to be considered carefully. Organic
mulches, particularly fine materials, are generally unsuitable for use
on green roofs as they can be easily blown off the roof, degrade
rapidly, block drains, or create a fire risk in hot dry conditions.
The saturated bulk density of any proposed mulch layer must
be included in the weight loading calculations for the green roof
build-up.
The University of Melbournes Burnley campus has a demonstration green roof with four distinct growing substrates. These are based on recycled
crushed roof tile; bottom ash from coal-fired power stations in NSW; scoria quarried locally to the west of Melbourne; and an ash-based mix with a
high proportion of composted pine bark. Substrates have been installed at different depths to compare the effects on plant growth
74
Roofs
Substrate installation
On large green roof projects, growing substrates can
be installed by crane or by blower. Substrate may be
delivered in multiple bulker bags, typically of one cubic
metre capacity, although a larger crane lifting bags of
greater volume may be possible if site access permits. Care
must be exercised in point loading of substrate on to the
roof and movement across the roof (see Chapter 4.1).
Blowing a substrate involves the use of a compressor
pump and hose to blow the substrate up to the roof.
Sometimes substrates that are blown onto a roof
will have altered properties (due to finer particles
aggregating during the process) and may need re-mixing
on the roof to ensure success.
Growing substrate should be delivered before the day
it is to be installed and stored as closely as possible
to the crane, with clear access for the forklift or other
machinery that will transport it to the crane lifting point.
Growing substrates should be installed with minimal
handling and be moist to reduce the release of fine
particles into the air. Appropriate personal protective
equipment should be worn: gloves, dust filter masks,
safety glasses and hardhat.
5.7 Vegetation
A range of planting stock can be used for green roofs,
including seed, cuttings, seedlings, tubestock and larger
containerised plants. See Chapter 3 for information on
species selection.
Planting is best completed in autumn and winter to assist
plant establishment before summer. Irrigation should be
provided while the plants establish. Depending on the
time of year and rainfall, establishment irrigation could be
required for up to six months.
It is helpful to acquire container-grown nursery plants that
have been grown in the substrate they are to be planted
into; otherwise, reduce the amount of potting mix held
around the roots when transplanting into the green roof.
Controlled release fertiliser (CRF) can be added to
the growing substrate or applied after planting is
completed (top dressing). Careful consideration of rates
and application methods is needed to ensure proper
distribution and to limit any rapid discharge of nutrients
(more information on plant nutrition is provided in
Chapter 8).
Trees planted on green roofs will require a deep substrate
as well as anchorage to prevent wind-throw. Various
anchorage systems are available as illustrated in Figure 19.
Tree bracings must be checked regularly to ensure they
are functioning as specified, and not causing damage to
the tree. Trees will require construction of a tree pit in the
substrate to house the tree roots: this needs to be deep
and wide enough for lateral root growth to ensure tree
stability. Consult an arborist for specialist advice.
Bulker bags of substrate moved around the site, at ground level,

prior to being lifted by crane at the demonstration roof at The
University of Melbournes Burnley campus
Substrate was blown onto the green roof in the City of

Monash, Glen Waverley. Image Junglefy
Contract grown plants

Plants can be sourced from retail nurseries or grown
at home for small projects. Generally, plants for larger
projects will be grown to a contract with a wholesale
nursery. Contract growing lead times may range from
several months to more than a year, depending on
the type of vegetation that is required. The growing
contract will specify a date for completion and delivery
of plants. It should outline the terms and conditions of a
further holding period, for instance, if the planting date is
postponed because of delays in construction. Ensure plants
purchased are weed and pest free look for nurseries
with good hygiene. If in doubt, remove the top centimetre
of growing medium to reduce the weed seed bank.
75
Roofs
Figure 19. Tree anchoring systems
Anchor straps and

dead man system
Root ball anchorage

to kerbing surround
Plate anchorage
system
5.8 Thermal insulation

In some cases, a green roof may include thermal insulation,
typically a layer of extruded polystyrene. While this can
be positioned below the roof deck, installation above the
waterproofing (known as an inverted green roof) is preferred,
as it further protects the membrane from condensation and
physical damage. Advice should be sought from a building
energy consultant to establish the value of additional insulation,

considering the insulating properties of the green roof assembly,
substrate and vegetation. Research has been conducted into green
roof insulation values in Adelaide and can be found at the Building
Innovation Fund website of the South Australian Government.
76
Roofs
5.9 Leak detection

Leak detection is carried out when the waterproofing installation is complete. There are three methods typically used for testing the
effectiveness of the waterproofing layer on green roofs:
Electrical field vector

mapping (EFVM)
Is suitable for electrically conductive and electrically grounded roof decks such
as steel and reinforced concrete roofs. EFVM can be used on wooden roofs or
precast concrete slab roofs if a conductive layer of metal foil or mesh is applied
to the roof deck before the waterproofing layer is installed. The decision to use
EFVM must therefore be made at the design stage.
Destructive testing
Is used for preformed waterproofing membranes. The membrane is perforated

at the lowest parts of the roof deck to check for the presence of any water
beneath the membrane. The penetrations made through the waterproofing must
then be repaired to restore the membranes integrity. Destructive testing may
be the only method that can be used on older existing green roofs. For new
projects, EFVM should be considered during design, as it is simpler, safer and
non-destructive of the waterproofing system.
Flood testing
Is suitable only for flat roofs with slopes of up to 2 per cent. Flood testing
involves temporarily blocking the roof drains and flooding the roof membrane
with a known depth of water for a set period of time. The weight loading of the
roof must be checked against the weight of water that will sit on the roof during
the test. This ensures that the structural integrity of the building
is not compromised.
It is advisable to perform an additional leak test prior to

installation of the growing substrate if significant time has
elapsed since the waterproofing was completed, or if there
has been construction activity or other traffic on the roof.
The repair of leaks presents a greater challenge once the
growing substrate and vegetation are installed. However,
EFVM leak detection should be performed at this time
(project completion). It may also be carried out prior to
the expiration of membrane warranties.
Electrical field vector mapping: An electric field is created by

applying water on the surface of the membrane and using
the water as a conductive medium. The EFVM equipment
delivers a low voltage pulsating electrical charge between the
non-conductive waterproofing membrane and the conductive
structural deck. Source: International Leak Detection Australia
77
Roofs
5.10 Irrigation
An irrigation system is highly advisable on green roofs: to extend
plant species selection options, to improve plant growth rates and
increase long-term vegetation success thereby ensuring aesthetic
and environmental (such as building cooling, stormwater reduction)
outcomes can be achieved. Planning for irrigation on a green roof
should consider the site layout and conditions (access, exposure),
type of plants, climate and water supply issues (pressure, quality,
etc.). Substrate properties and depth are also important as they
influence water infiltration, holding capacity and drainage. In most
cases, irrigation design will be heavily influenced by the nature of
the water supply resource (for example, harvested vs. potable water)
and a water budget should be used to guide not just irrigation but
also plant selection (see Chapter 3). In larger green roof projects,
irrigation is best undertaken by a specialist consultant to guide
system design, component selection, installation and maintenance.
Table 11 provides an outline of different options for irrigation of
green roofs.
Automatic systems
If an automatic irrigation system is to be installed on a green roof,
consider a system that incorporates a rain sensor that shuts off
the system in the event of rainfall above a certain threshold. This
removes the risk that the roof loading may be compromised if the
irrigation system is running during a heavy downpour. Even automatic
systems require regular physical checks and operation tests.
Low irrigation
It is important to understand that, while some succulent species
can survive on rainfall alone, plants that experience moisture stress
will decline over time. This leads to a loss of vigour, leaf shedding,
canopy reductions and ultimately plant death. Plant failure means
more water run-off from the roof, less transpirational cooling
and more opportunities for weed invasion. As such, irrigation is
advisable. However, if designing for very low water use, select plant
species that are better able to tolerate the extreme moisture
stress on a green roof during a typical summer. Selection tools

to guide the identification of low water use plant species can be
found at the Smart Garden Watering website. Another option is to
provide supplementary irrigation on a contingent basis during the
hotter periods of the year.
Depending on the level of attention that can be provided, inclusion
of indicator species with moderate requirements for water may be
helpful to show when supplementary irrigation is necessary. This
avoids compromising the performance of all the plants.
Irrigation frequency
During the establishment phase after planting, irrigation may be
frequent, for example, two to three times per week. For food
crops, irrigation will also be necessary during high activity phases
of the growth cycle, such as when the plant moves into flowering
and fruit set. The frequency of irrigation should be matched to the
drainage and water-holding capacity of the mix: frequent irrigation
of a very free-draining substrate is likely to waste water.
The irrigation delivery method will partly determine the timing
of irrigation. Watering in high daytime temperatures will transfer
more heat into the building, as water heats up as it passes through
the hot growing substrate and transfers some of this heat into the
building when it drains onto the roof surface. For surface and subsurface irrigation, there is little to no wetting of the foliage, which
lowers the risk of fungal disease. If spray irrigation is used, it should
be applied very early in the morning to enable foliage to dry off
throughout the day and thus reduce the likelihood of disease.
Moisture sensors
Be aware that moisture sensors used to estimate moisture
content in standard landscaping soils do not provide reliable
information about the moisture content of free-draining, porous
growing substrates used on green roofs.
An irrigation system is laid at the Victorian Desalination Project

green roof, Wonthaggi. Image: ASPECT Studios
78
Roofs
Table 11. Irrigation methods for green roofs

Delivery method
Advantages
Disadvantages
Microspray
Low cost, visible, easy to install, reliable
Uneven distribution (plant interception), high

water loss (wind, evaporation), foliage wetting
(increased disease potential)
Surface drippers/
perforated pipes
Low cost, visible, even delivery of water
Moderate water loss
Sub-surface drippers/
perforated pipes
Low cost, moderate efficiency (water delivery to

root zone)
Non visible (difficult for maintenance), higher

potential for damage by people digging
Sub-surface capillary
High efficiency
High cost, maintenance and repair is difficult

because not visible, capillary rise of substrate
needed or water will not reach plants
Wicking associated with

irrigation in drainage layer
High efficiency, ease of installation
Linked to proprietary systems, capillary rise of

substrate needed, this may be unsuitable for plant
establishment if the water is applied too deep for
the plant roots to reach
Hose
Good for domestic application for easily accessed

areas, not so good for other areas. Allows
monitoring to occur at the same time
Cost (requires someone to be present on site),

low water efficiency, foliage wetting, uneven
distribution
5.11 Wind considerations

Even on flat roofs, wind uplift may present serious challenges for
retention of substrate and plants. Wind damage can be dangerous
to people and property and costly to repair. Retention systems may
be required to ensure that materials cannot be blown off the roof.
Wind uplift pressure is lowest on the centre of the roof and highest
at the edges, around the perimeter and at corners. The higher the
building, the greater is the risk. On pitched roofs, the roof peak is
also subject to uplift. Minimising untethered components greatly
reduces the risk of damage to the green roof by uplift.
Where possible, waterproofing should be fully adhered to the
roof, or mechanically fixed. For waterproofing layers that are
not bonded to the roof, the green roof assembly must provide
adequate ballast to prevent uplift. Edge treatments are the most
critical: the un-vegetated zone around the perimeter of a green
roof (see Chapter 5.13) may require heavy concrete paving slabs
Perforated screens reduce wind flows on The University of Melbournes

demonstration green roof at Burnley campus
rather than loose gravel ballast. The materials used must conform
to the design wind load calculated for the specific green roof
location.
On some green roofs, perimeter balustrades or parapet walls will
provide some protection against wind flow. Other treatments,
such as jute erosion control netting (see Chapter 5.12) or coated
wire retaining systems, may be useful.
Plant selection may also be used to mitigate the impact of winds. If
the tolerance of different species to wind exposure is understood,
plantings can be planned so that the lowest-growing, most robust
species are planted in the most exposed areas. Taller, less wind
tolerant species are installed behind them. The resulting gentle
gradation of vegetation heights interrupts, and slows, wind flow
over the planting.
Fytogreen design uses wind tolerant species to shield others on the

green wall at the Triptych Apartments, Southbank
79
Roofs
5.12 Slopes and wind protection

Landscapes on pitched roofs are subject to wind forces and gravity
affecting the stability and retention of the growing substrate and
plants. In many cases slippage can lead to poor plant performance
and ultimately green roof failure. For roof pitches of up to 15
degrees, no additional protection is needed, unless there are
strong wind issues on the site. Waterproofing must be rootresistant, and covered with a protection mat. A drainage layer
is not always required as the roof can drain effectively through
gravity. The stability of steeply pitched green roofs is increased by
maintaining vegetation cover: provision of irrigation is essential.
For green roofs constructed on pitches greater than 15 degrees,
basic protection can be provided through anti-erosion jute
netting installed just below the substrate surface to provide some
anchorage to plants (see image). This netting breaks down over
time, and is used simply to help keep the substrate in place whilst
the plants establish.
Figure 20. Layers of a sloped roof

Erosion
Control
Netting
A green roof on a slope can include a

drainage layer with large cells to retain
substrate as well as a layer of erosion
control netting laid close to the top of the
substrate to help retain substrate and
plants during the establishment period
Greater protection can be provided on steeper sites by using a

drainage layer with large cells, or cups. The growing substrate fills
the cells of the drainage layer, reducing slippage and providing
spaces for plant roots to grow, ensuring further stabilisation (see
Figure 20). A filter sheet must be placed beneath the drainage
layer to reduce wash-through of fine particles from the substrate.
For green roofs with slopes between 20 degrees and 45 degrees,
honeycomb webbing, comprising multiple, enlarged drainage
cells, can be installed above the drainage and filter sheet layers
(see image). This holds the substrate in place, increases stability
and reduces slippage. Other specialised structural elements can
be incorporated to transfer shear forces into stable, reinforced
abutments that form part of the roof structure, or wind barriers
can be installed.
Growing
Substrate
Anti-shear
drainage layer
Roof
Protection
Layer
deck
Water-retention
matting
Waterproofing
Membrane
Anti-erosion jute netting installed on a sloped green roof. Ideally a

layer of substrate should be covering the netting, which will degrade
over time. Image: PAD Creations
Honeycomb webbing used to stabilise substrate on a pitched green

roof. Image: KHD Landscape Engineering Solutions
80
Roofs
5.13 Hard landscape elements

Some of the functional elements that are used in green
roofs include:

non-vegetated zones
retaining edges
topographical construction
planting containers
drains and gutters
flashings
a range of other elements, not discussed in detail here, such
as: harness attachment points; controller boxes/solenoid
boxes (to house irrigation components); decorative and
functional landscape elements such as decking, paving, seating,
shade protection, ponds and lighting
Retaining edges
Edging can be used to define and retain planted and nonvegetated zones across a green roof. It can include concrete,
stainless steel, recycled plastic or aluminium products; L-shaped
edges are installed above the filter sheet and often have
perforations to allow drainage through the profile.
The colour of materials should be considered as this will affect

their heat gain. Consider location of shade structures as additional
elements.
Non-vegetated zones
Non-vegetated zones are used to group roof penetrations, vent
pipes and other upstands and assist in lateral drainage. They are
generally constructed with large diameter aggregate rock or ballast
(16-32 mm size), rather than the growing substrate, and provide
additional lateral drainage into the roof drains. They are usually
between 300-500 mm wide and are separated from the roof
perimeter ballast by metal edging installed around the planting
area. Similar vegetation-free zones may be created through use of
paving slabs or ballast to provide access pathways across the green
roof, or as firebreaks on very large roofs.
Non-vegetated zone around hard infrastructure on a roof
Edging can be used to separate different substrates on the roof
Topographical construction
Blocks of polystyrene foam can be used to build up areas to create
mounds or hills without the additional weight of the substrate.
Topographical variations on a green roof create different growing
conditions and microclimates to increase habitat opportunities for
beneficial insects, as well as visual, aesthetic interest.
The build up of this green roof hill in Queen Street, Melbourne, is

created from recycled expanded polystyrene blocks, overlaid with a
deep drainage layer to contain the growing substrate
81
Roofs
Planting containers
Drains and gutters
Planters must be made from weather resistant materials, and the

components must be physically and chemically compatible with
each other. Common examples of materials used to build planting
containers are powder-coated metal, galvanised steel, ceramic, timber,
UV stable plastic and glad reinforced concrete (lightweight concrete).
All drains must be accessible for maintenance, protected from

blockage by leaf litter and substrate wash, and housed with
inspection chambers, drain covers, filters or strainers. Inspections
after construction, following storms and every three months are
recommended.
Selection of drainage hardware depends on the required function
and appearance; examples are provided in the section on drainage
in Chapter 2. For drains located flush with the roof surface, a grille
should be installed to prevent drain clogging.
Flashings
UV stable plastic containers are used to add greenery to this rooftop

garden in Little Collins Street, Melbourne
Roofs with a parapet that extends above the roof deck require
installation of a cover (flashing) to protect the building fabric.
This should be included in the waterproofing installation to
ensure that membrane terminations, and any areas of membrane
extending over the vertical and horizontal surfaces of the parapet,
are not exposed.
Figure 21. Functional elements on a green roof can include flashing (capping) and non-vegetated zones
Flashing
Non-vegetated
Zone
Growing
Substrate
Drainage Layer
Protection
Layer
Waterproofing
Membrane
Roof deck
82
Roofs
Stages of construction:
Building the City of Monash green roof
1
Substrate was blown onto the green roof in the City of

Monash, Glen Waverley. Image Junglefy.
1 The roof deck is ready for installation of the green roof: waterproofing treatment was not required on this clip-lock steel roof
2 A protection layer is used to cover the roof deck 3 Drainage sheets are installed over the protection layer 4 Abutting drainage
sheets provide full coverage of the area to be planted 5 Substrate is pumped up to the roof from ground level and installed via a
blow hose. 6 Edging strips are used to separate planting areas from non-vegetated walkways 7 Planting follows a specified design
8 The final product
Images courtesy of PAD Creations and Junglefy
External green walls, Illura Apartments, Roden Street,West Melbourne
6. Building &
installation
green walls
Green wall systems vary greatly in their design and construction from DIY
projects to modular green wall systems available to buy off the shelf, through
to proprietary systems that are custom-fitted to a wall. Specialists in green
wall design and installation can provide advice on the most suitable system and
the best construction approach. Green walls can deliver more than aesthetic
benefits, and this requires consideration in the design stage. This chapter
provides advice on the structures and components required for green wall
systems, waterproofing, irrigation and nutrition, vegetation and lighting. This
information should be read prior to starting a green wall-building project.
84
Walls
Building & Installation - Green Walls
6.1 Structures and components for

green wall systems
Hydroponic green wall systems can be either modular containers
or large panels. The systems are installed via brackets that sit out
from the load-bearing wall (or a stand-alone structure) to create
an air gap between the wall (or other structure) and the backing
sheet of the green wall system. In a hydroponic system, an inert
growing medium is provided to which the plants physically anchor,
such as a horticultural foam, a mineral fibre or a felt mat. These
materials can act as a water retentive sponge, although the more
they soak up the heavier the system becomes. The advantage of
the hydroponic system is that there is no structural decay of the
growing medium, no salt build up from fertilisers and nutrients
are supplied in a precise and controlled manner. Over time, plant
roots grow and ramify through the entire system to create a very
robust network.
Substrate-based systems use substrate-holding containers made of
plastic or metal. The substrate is packed directly into the empty
container or placed in a water permeable, synthetic fibre bag.
The containers are connected together and anchored to the wall

or to an independent, structurally secure metal rack or framework.
Alternatively, plastic or metal growing containers can be hung
on a metal grid fixed to the wall. Individual growing containers
can be removed for maintenance or replanting. Most substratebased systems are designed for automatic irrigation, just like the
hydroponic green wall systems.
The growing medium in these systems provides a structure to
support the plant and facilitates water, air and nutrient access,
decreasing the need for constant management associated with
hydroponic systems. However, over time the reserve of nutrients
will be exhausted and there can be a build up of salts in the
growing medium. Traditional potting mix is not a suitable substrate
for green walls. A specialist green wall provider will advise on
the most appropriate growing medium for a particular green
wall design. See also Appendix A for information about substrate
characteristics.
Figure 22. Types of green wall configurations

Modular system
Water proofing
Hydroponic system
Water proofing
Wall
Wall
Irrigation
Irrigation
Modular panel
(hydroponic)
Green wall systems vary

enormously, these are two
general types. - modular,
which can be hydroponic
or substrate based, and
felt covered hydroponic
panels. Note that the
support structure and
waterproofing are optional
and depend on the site
Modular panel
(substrate)
Drip tray
Felt Covered
Panel (with
irrigation
concealed)
Support
structure
Drip tray
Support
structure
85
Drip trays are used to capture excess irrigation water from the
growing medium as well as water droplets that drip off foliage. The
size of the drip tray should be sufficient to hold an entire irrigation
cycles water volume (before draining away prior to subsequent
cycles starting). Drip trays may not be necessary if the run-off is
intended to irrigate vegetation below the green wall. If drip trays
are not used, ensure run-off does not create slip hazards, damage
the building fabric or provide excess moisture or nutrients to
ground-based plantings below.
Water captured in the drip tray or reservoir at the base of the
planting system can be pumped back to the top of the wall for
re-use rather than being wasted, provided that it is treated to
prevent build-up of nutrients. Drip trays should have a drainage
pipe of sufficient diameter to empty the drip tray or manage
water capture sufficiently to mitigate overflow of the tray. Fascia
treatments may be added to conceal the edges and functional
elements of the green wall system, such as the irrigation system
and drip tray.
6.2 Waterproofing
Walls
Waterproofing walls
- lessons learned
This indoor green wall is located within an office
conference room in Melbourne. Within a week
of installing the waterproofing and drip tray
treatments, water leakage was observed. The area
connecting the waterproofed wall to the drip
tray had not been completely sealed and allowed
water to collect and drain between the two.
The modular nature of the green wall assembly
enabled this fault to be easily repaired the area
was sealed, and this mitigated any further
damage.
This example reinforces the importance of
testing and checking the work undertaken and
completed by every contractor against project
specifications.
Waterproofing is project-dependent; in some cases there will be

a sufficient air gap between the back of the planting system and
the wall, making waterproofing treatment unnecessary. The air gap
prevents movement of water between the wall and the planting
system, and air-prunes plant roots to reduce the risk that they
will directly contact the wall and provide a path for movement
of moisture. Provision for an air gap between the planting system
and the building wall will also prevent growth of mould. Where
waterproofing is necessary, it will prevent damage to the wall
from moisture and dissolved salts from fertilisers. In some cases
the supporting wall might be considered waterproof as is; for
example, a preformed concrete wall may be thick enough to be
rated as fully waterproof, or a wall constructed from marinegrade plywood will have some degree of waterproofing from
the glues used within the ply. Consideration must be given
to waterproofing penetrations to the wall as well as junctions
between surrounding fascia (if used) and junctions between wall
waterproofing and drip trays (see box). Roller-applied liquid
waterproofing treatments can be used on internal and external
green walls. When considering waterproofing for any green wall,
seek advice from a waterproofing consultant to ensure the most
suitable treatment is chosen.
The manufacturing and installation of waterproofing membranes
should comply with the Australian Standard for membranes
used to waterproof exterior areas of buildings (AS 4654.2-2012
Waterproofing membranes for external above ground use
Design and installation). Waterproofing membranes used for
internal walls should be manufactured and tested to AS/NZS
4858:2004 Wet area membranes. Waterproofing treatment should
follow the procedures used in other internal areas of residential
buildings, such as bathrooms, kitchens and laundries. These are
specified in AS 3740-2010 Waterproofing of domestic wet areas.
An improperly sealed join created a leak behind

this green wall
86
Walls
6.3 Irrigation and

plant nutrition
Green walls cannot be sustained without irrigation. Interruptions
to the water supply are a common cause of plant failure on green
walls. Systems designed with inbuilt irrigation should mitigate plant
losses due to inconsistent moisture management, although errors
can still occur.
Automated, remotely controllable irrigation systems are used
for walls in high profile locations, or in situations where access
is challenging. Note that the quality, design and costs will vary
between different systems. The most sophisticated systems enable
the maintenance supervisor to keep track of the automated
performance of the system, including the volume of irrigation
delivered, its frequency, substrate moisture content, as well as
pH and nutrient levels in the water supply. The settings can be
overridden if needed; for instance, the frequency or duration of
irrigation cycles may be increased on hot days.
In hydroponic systems, plant nutrition is delivered by a fertiliser
injection system that releases controlled doses of fertiliser into
the irrigation system (fertigation). Management of fertigation
systems and rates of delivery requires specialist knowledge, as it is
more complex than fertilising soil or growing media. Hydroponic
systems require continual monitoring of pH, water hardness and
total dissolved solids (TDS), and adjustment of these parameters
where necessary.
This green wall on the roof of a health care centre in Marion,

South Australia, incorporates an inbuilt water tank to provide
water supply and structural integrity for double sided modular
wall systems, with plantings including strawberries and herbs.
Image: Fifth Creek Studio
For hydroponic green wall systems, the fertigation system may

apply 0.5-20 litres of irrigation solution per square metre per
day. Internal green wall requirements are at the lower end of this
range, and external green walls at the higher end. Irrigation cycles
typically last a few minutes and will be required several times a
day. Keeping irrigation volumes low minimises waste and reduces
run-off. Irrigation run-off may be captured in a tank at the base of
the wall and recycled back through the green wall system.
Green walls that use a high quality, water-retentive growing medium,
and are not in an exposed or particularly hot location, may thrive
on a weekly watering regime. In most simple, soil-based systems,
including DIY systems, controlled release fertiliser is mixed in with
the growing medium, rather than using a fertigation system.
Irrigation must be available as soon as the plants are installed in
the wall system. The irrigation system requires a water meter to
monitor irrigation volume, and a pressure gauge to monitor the
even application of water. The need for ongoing regular irrigation
and the expectation that water will be used sustainably means that
stored (harvested or recycled) water should be used whenever
possible, so a pump is necessary.
87
Walls
6.4 Vegetation
The size of plant materials used in green walls will depend on the
required look and finish of the wall at project completion. Planting
densities can be as high as 25 to 30 plants per square metre.
Decorative patterns can be designed by repeat planting across
an area; however, these patterns can be difficult to implement
if shadows and light across the different parts of the wall have
not been considered. Systems incorporating smaller plants at the
outset will take longer to fill out than those using well-established
container plants. The dimensions of the planting module will
determine the size of the planting stock. Different green wall
systems will be better for different types of plant growth habits,
from those that grow upright to those with a clumping growth
habit, scrambling, cascading or creeping. See Chapter 3 for
information on plant selection.
6.5 Special considerations for walls

Lighting is often required for green walls positioned in low light
exposure areas. Many green walls are installed within non-lit areas.
Lighting green walls is highly specialised, requiring the services
of a lighting designer or engineer. Plants require very specific
lighting quantities and qualities to photosynthesise, grow, flower
and develop appropriately. Tropical and subtropical green wall
installations can generally survive in lower light conditions than
Mediterranean, temperate plantings. Extensive knowledge of
horticulture and design of green wall systems is needed to
choose the right species for the light levels available on-site.
Internal green wall. Image: KHD Landscape Engineering
Another consideration for green wall installations is air movement

around the foliage. This is important to help prevent fungal growth,
and additional ventilation may be needed to ensure sufficient air
movement for indoor walls. Outdoor walls usually create their
own microclimate that creates enough air movement, but in very
sheltered positions attention should be given to this issue.
Facade greening on the Council House 2 rooftop, Little Collins Street, Melbourne. Image: Ronstan Tensile Architecture
7. Building &
installation
green facades
Green facades can range from complex systems for multi-storey buildings, with
plants growing in containers at different heights, to simpler systems where the
plants grow from the ground, allowing inexpensive installation of greenery on
low-rise buildings. This chapter provides information about building and installing green facades. The information should be considered prior to starting a
building project.
89
Facades
Building & Installation - Green Facades
7.1 Wall protection and different

facade treatments
Waterproofing treatment of the wall is not required for green
facades. It is important to select plant species with a growth habit
that will not damage the fabric of the wall. Some species with
adventitious roots or scrambling stems can damage the building
fabric over time, such as Common Ivy (Hedera helix). However,
self-clinging climbers are exceptionally well suited to many vertical
building surfaces, particularly old stone structures or those with
minimal exposed mortar, and have lasted a long time without
negative impacts on the building fabric.
For containerised systems, plant species choice and the spacing

and volume of containers are critical for establishing effective
facade coverage. Specialists in green facade design and installation
can provide advice on the most suitable system and the best
construction approach.
Plants can damage buildings by physical and chemical means, over

timescales of centuries. Damage can be superficial, causing only
aesthetic changes to the facade, or more structural damage may
result, usually over much longer time periods. If in doubt, choose
a green facade where the plants are grown on a support system
that is installed separately from the building.
Metal systems have the longest lifespan and require less

maintenance. Stainless steel cables and trellis are low maintenance
and have a long lifespan and probably offer the greatest flexibility
to suit a variety of plant species and wind loads. Steel nets
and mesh provide additional options, with closer weaves than
horizontal and vertical cabling.
Support systems for facades involving plants that have tendrils

or twining stems (see Chapter 3) may be made of plastic, timber,
metal, or stainless steel cables or cable mesh. Design of the
support system must consider the intended lifespan of the facade,
the growth habit of the plant species, and how spacing and offset
from the wall can help to provide the desired end result. Possible
designs are shown in Figure 23.
Support systems are suitable for very structured arrangements

where greening has to be maintained away from windows or
because of the other building constraints, such as the geometry
of the building facade. A facade support may provide aesthetic
appeal when the plants have not yet grown to full size and in
winter where deciduous climbing species are used. Support
systems can be separate from a building and used to create a
green facade for privacy or shade.
Wooden trellises are prone to damage by weather and plant

growth and many plastics become brittle over time with ongoing
exposure to UV light, heat and cold.
Figure 23. Support structures for green facades grown with twining climbers
Single cables provide subtle

screening and prevent people
climbing
Stand-alone trellis systems

provide intrinsic visual interest
Containerised mesh system

for multilevel structures
Wall-mounted cable grids can

cover plain unsightly walls
90
Facades
7.2 Soils and

growing substrates
Plants used for facade greening may be grown in soil in the
ground, or in containers filled with a well-designed growing
medium. The principles outlined in growing substrates for green
roofs, outlined in Chapter 5 and Appendix A are also relevant to
green facades.
The use of planter boxes, mounted at varying heights above the
ground, can allow greater coverage of the facade, where the
building is so tall that ground level plants will not reach the top.
The advantage of in-ground planting, where soil is of a reasonable
quality, is that the plants will have more access to water (the soil
will not dry out as quickly as in a container) and will have more
space for their root systems to grow.
Container growing media must be designed to support ongoing
growth of plant shoots from a limited, contained root volume, and
at elevation. Although many climbing plant species have superficial
root systems and may thrive in a small volume of substrate, there
is a notable link between root volume and sustainable foliage
volumes. Climbers required to cover greater areas will require
greater substrate volumes. However, weight loading restrictions
may limit the depth that can be supported for container systems
at elevation.
In-ground plantings will generally outperform container plantings
in the long term. Ensure the planting bed soil or growing media
has a suitable balance of porosity and water-holding capacity,
and an adequate supply of nutrients to ensure optimal growing
conditions. In a garden setting with good quality soil and adequate
irrigation, there should be little to impede strong plant growth.
In city landscapes, with large areas of impervious paved surfaces
and soils that may be highly compacted, soil structure may be
poor. In such cases, consider installing a structural soil that can
be compacted to enable footpaths or other hard surfaces to be
installed, while still providing adequate porosity to support root
growth. In some buildings the foundations sit out from the wall,
underneath the ground these footings should be set deep if a
garden bed is planned adjacent to the wall.
7.3 Vegetation
For rapid coverage of a green facade, plant specimens should be
healthy and vigorous, with numerous basal shoots. They should be
of the largest possible size to suit the installation.
To support the vegetation at installation, the growing substrate
used to support container-grown facade plantings should
incorporate controlled-release fertiliser at planting (see more
information about plant nutrition in Chapter 8). New plantings
should receive irrigation to promote their strong establishment,
which depends on season planted and plant size. Establishment
is when new roots have grown and the plant is acclimatised and
actively growing.
Pruning and training of new plants is essential to promote the
development of an effective facade. Plants may need to be
trained to the facade support, or temporarily attached to the
wall after planting, to encourage upward growth. Once the plant
is established, the main runners should be trimmed to encourage
lateral shoots that will create a more radial growth pattern. If this
is not done, the climbers will typically branch out only once they
have reached a significant height, and it may take years for the
lower portions of the facade to receive any coverage. The use of
diagonally oriented cables on facade systems facilitates horizontal,
as well as vertical, growth of the plant (preferred over the plant
shooting straight up) and thereby increases the density of foliage
cover. For long-term installations, pruning to rejuvenate might be
required. As climbers age their growth can decrease and cutting
back to hard wood can revitalise a plant and allow for longer
lifespans. This means that after five to seven years, especially
with woody climbers, it may be necessary to prune back a large
portion of foliage.
Seek the advice of a horticultural consultant to ensure the volume

of soil or growing medium will support the desired height and
spread for the green facade.
Close-up view of adherent discs that enable species such as

Parthenocissus tricuspidata (Boston Ivy) to self-attach to this building
facade at RMIT University, Melbourne
91
7.4 Drainage and

irrigation
Garden beds, or at-ground planter boxes used for climbing
plants for facade greening, should have drainage appropriate
for the plant species selected for use. Container systems
placed at elevation on the face of a building should have
a free-draining growing substrate to avoid potential
waterlogging in the event of prolonged periods of wet
weather. The potential for ponding of water above the top
of the growing substrate should be minimised by providing
overflow drainage holes in the sides of the container, just
higher than the level to which the container is filled. In most
cases, run-off through the base of the growing containers
will simply run down onto the ground beneath, but drip
trays can be installed to collect water.
The vigour of many climbing plant species means that
irrigation will be required to maintain high-density foliage
cover and long-term performance of the green facade. Inground plantings in domestic settings will need irrigation
at least during the hotter months, if not year-round.
Harvested, recycled water should be used for irrigation
wherever possible. Irrigation frequency will depend on the
plant species selected, the type of growing medium used,
and how exposed the facade is to sun and drying winds.
At-ground plantings can be irrigated by automatic systems
or manually with a hose. Surface or sub-surface dripper
systems are suitable automatic systems. Irrigation supplied
to elevated planters requires appropriate water supply
pressure from tank, recycled and mains water supplies. See
Chapter 5.10 for information about irrigation systems and
methods of delivery and Chapter 3 for more information
on drainage and irrigation in general.
Facades
Facades in containers
lessons learned
A roof garden incorporating green facades was built
at Council House 2, central Melbourne, in 2006. Its
design included the incorporation of 950 mm deep
plastic planters, connected to a cable and stainless steel
trellis (X-TEND) mesh for growth of the facade. The
intention was to increase greenery across the building
through use of the roof and facades.
Unfortunately, the facade plantings have not grown well
due to multiple problems with the planters, growing
substrate and irrigation. The black colour of the planters
leads to considerable heat gain in the root zone over
summer, causing difficulties for plant growth. The
planters also tend to split, the side wall plastic seemingly
unable to tolerate the high bulk density of the growing
substrate. Additional metal frames were used to support
the replacement containers. The substrate itself has also
had issues, with plants failing or growing poorly and a
considerable drop in the total volume since installation.
A further complication has been the irrigation system.
Each planter is irrigated via combination of a valve, water
reservoir and foam wicking, all enclosed in the base
of the container. The valves function at a much lower
pressure than the mains supply, meaning most failed
when they were first operated. This in turn affected
any possible capillary irrigation upwards to the root
zone in each container, leading to extensive plant death
shortly after installation. Replanting has occurred but
all containers now need to be hand-watered. The City
of Melbourne is currently investigating cost effective
options for resolving these problems.
The City of Melbourne recommends thorough research
or peer review to assist and support decision-making
around the design and use of new technologies.
Planter boxes on the City of Melbournes Council House

2 roof garden, Little Collins Street, Melbourne, have not
performed as well as expected
Weeding the vegetable bed on the Demonstration Green Roof at The University of Melbournes Burnley campus
8. maintenance
This chapter provides information to help with the development of
maintenance plans. A detailed maintenance plan will outline performance
standards, tasks to be undertaken and the resources required to achieve
them. Once created, maintenance plans should be reviewed at least
annually to ensure all maintenance needs are being met.
93
Maintenance
Maintenance
8.1 Maintenance planning

A maintenance plan should include a clear description of:

maintenance objectives created based on the design intent,

or the landscaping or environmental objectives that were the
basis for the roof, wall or facade development
performance targets, such as the time frame for complete
coverage of an area by plants and foliage
responsibilities of various personnel involved in operating
the building, outlining the type, scope, duration of task and
occurrence
training requirements (such as Working at Heights
certification) and safety equipment
resources available
A supervisor may be designated to oversee the overall and

ongoing management of maintenance activities, and can provide
direction to maintenance staff and assess that work has been
carried out satisfactorily. The supervisors role will involve:

Maintenance planning should also incorporate risk management,

with the aim of reducing or eliminating the likelihood of failure
that could result in property damage or personal injury.
For large projects, maintenance planning is often based on
asset management planning where the whole life of the asset is
considered, including design, construction, establishment, operation,
maintenance, renewal and demolition/replacement.
For some green roofs, walls or facades, particularly those located
on commercial premises, maintenance will be undertaken
by someone other than the building owner. A maintenance
agreement with the installation company or with a recommended
third party may be the most economical way to ensure the
best long-term performance of a green roof, wall or facade. If a
maintenance contract is used, it is important to be clear about the
duration of the maintenance agreement, the scope of maintenance
responsibility, and the need for handover at changeover to either
new contractors or back to the building owner.
scheduling of maintenance: flexibility may be needed, as, for

instance, additional visits may be necessary to repair damage
following extreme weather events
signing maintenance contractors in and out at the start and
end of a visit, offering a toolbox talk at the commencement
of a visit, and providing keys and providing any specialist
equipment that is required
occupational health and safety: ensuring contractors have
appropriate certification; scheduling mandatory annual checks
(and repair or replacement if necessary of safety anchor points);
ensuring conditions are safe for maintenance staff to perform
their work; providing safety signage or other barriers to restrict
access during maintenance; and ensuring that staff understand
the process for reporting actual or potential hazards
informing other contractors who work on the building about
the roof, wall or facade, so that they do not inadvertently
damage the asset (for example, water service contractors
turning off water for a prolonged period)
Reactive maintenance was needed after a severe hail storm shredded succulent vegetation at The Venny, Kensington, in March 2010.
Image: PAD Creations
94
Maintenance
Maintenance
8.2 Maintenance tasks

Maintenance falls into a number of categories:
1.
Establishment maintenance occurs during the first

one to two years after installation and is undertaken
to fully realise the design intent and outcomes. For
vegetation, this includes tasks such as pruning, weed
control, and irrigation to ensure healthy and vigorous
plant growth.
2.
Routine or recurrent maintenance includes regular

works that are undertaken to ensure the roof, wall or
facade is maintained to a minimum or required standard
of appearance, functionality and safety. For vegetation, this
can include tasks such as weeding, pruning, removal of
leaf litter and, in some cases, mowing.
3.
Cyclic maintenance is scheduled interventions at

less frequent intervals that maintain infrastructure.
It includes maintenance of the underlying building
structure and of specific components of the
green roof, wall or facade system. This may include
infrequent pruning or other formative management
of woody vegetation, such as coppicing, or annual
treatment of decking or other hard landscape
elements to maintain their safety and functionality.
4.
Reactive and preventative maintenance is

undertaken when some component of the system
fails suddenly, or shows signs of imminent failure.
Failure may be due to a long-term problem that has
gone undetected (such as blocked drains by tree
roots), or sudden damage resulting from an extreme
weather event (such as stormwater incursion).
5.
Renovation maintenance includes works that change

the design intent. This may arise after a change of
ownership of a building which instigates a desire for
change, through to remediation of a design failure
(see The Venny case study).
Some typical maintenance activities for green roofs, walls

and facades are outlined in the table below. These are
intended as a general guide only: each site will have its
own specific requirements and some listed will be more
relevant and/or specific to a wall, roof or a facade.
Access for maintenance

Roofs that are not generally accessible to the building
owner or tenants may need to be accessed by ladder,
using ropes and harnesses or other fall arrest systems to
work safely. For small wall and facade installations, within
a few metres of the ground, a mobile work platform at
ground level is probably the most efficient solution for
access. However, ropes and roof-mounted attachments
may be required for larger areas or higher buildings.
Green walls and facades extending more than 10 metres
above ground level will usually be maintained from a
roof-mounted work platform. A hybrid living wall system
developed in Adelaide addressed maintenance access
with an inbuilt platform at each floor level that allowed
safe access for maintenance of the vegetation and for
other services such as window cleaning.
At The University of Melbournes Burnley Campus, vigorous

deciduous climbers such as Boston Ivy (Parthenocissus
tricuspidata) are pruned twice a year to control size and to
keep stems away from windows, flashings, drains and other
building fixtures
95
Maintenance
Maintenance
Table 12. Common maintenance tasks
Maintenance Objective
Task
Maintain planting design
Plant replacement, infill plantings
Maintain plant growth
Remove waste plant material (leaf litter, prunings, weeds), inspect for signs of pests
or disease and treat as needed, make seasonal adjustments to irrigation volume and
frequency as needed, ensure adequate nutrition levels for plants; inspect after severe
weather events (e.g. wind or heat) to look for signs of stress
Minimise weeds
Mulching, weed control
Manage lawns
Regular mowing, annual renovation
Maintain trees
Regular pruning, annual tree inspection, brace and support as needed
Maintain climbing plants
Annual or biannual pruning to maintain density and cover and to remove growth from
fixtures (windows, drains). Rejuvenate to renovate habit and growth
Rejuvenate climbing plants
Vigorous pruning to renew stems and encourage new basal growth (every 5-7 years)
Monitor plant performance
Maintain records of plant health, vigour and coverage, pest and disease impact
Maintain substrate
Top-up of growing substrate may be required due to wind, rain or animal activity (check
the depth of the growing substrate before any additions are made to ensure weight
loadings are not exceeded)
Maintain irrigation (and

fertigation) systems
Manually test and inspect the irrigation system regularly and monitor any automated
systems (check volume of irrigation delivered, its frequency, substrate moisture content,
and, for hydroponic green walls, nutrient levels in the water supply)
Monitor plant nutrition
Maintain a log of fertiliser additions and records of pH and electrical conductivity values
before and after addition of fertiliser
Maintain drainage
Ensure roof drains are clear and functioning, remove dirt, litter and other deposits from
drain inspection chambers, check plumbing hardware, check condition of filter sheet and
deeper layers if necessary
Maintain non-vegetated zones
Remove vegetation from perimeter zones and around other equipment and fixtures
Maintain wind protection

features
Check the condition and fit of protection systems
Maintain safety systems
Check safety anchor points for fall arrest systems, check access points, e.g. ladders and
stairways, check electrical safety of power points, lighting and irrigation control system
Maintain waterproofing
Inspect flashings over waterproofing membrane terminations, inspect wall fabric for any
damage from water, fertiliser or plants, conduct leak detection of waterproofing on a
green roof if possible
Maintain other hardscapes
Clean or oil decking or furniture, inspect green wall or facade support systems for any
loose attachments or fittings
96
Maintenance
Maintenance
Fire
Maintenance plans must ensure that the vegetation present on a green roof, wall or facade does not create fire hazards. Dead
or dry vegetation must be removed as part of regular maintenance. Fire resistance can be increased by installing breaks in the
vegetation or using plants with low biomass (such as native grass tussocks with a low amount of leaf matter). Green facades with
deciduous or evergreen climbers are unlikely to create a fire risk as long as dry leaf litter falls away cleanly and is removed during
routine maintenance. Vegetation on green walls that receives regular irrigation and maintenance does not pose a fire hazard.
8.3 Plant nutrition

An important element of maintenance is ensuring that plants
receive adequate nutrition. This section provides information on
nutrition for roofs and facades. Walls are not addressed here
because green wall installers will provide specific instructions for
meeting the nutrition requirements of the particular plants in the
particular wall. Fertilisers for green walls are delivered in liquid
form, via the irrigation system (see Chapter 6.3).
Facade greening planted in the ground in a good quality, sandy

loam topsoil should not require additional fertiliser. The addition
of composted organic matter once or twice a year to garden
beds where facade greening is planted will supply nutrients and
improve water retention. CRF suitable for the species planted may
be incorporated into the garden beds, if desired, according to the
rates recommended by the manufacturer.
In consultation with the designer and client, establish the lowest

appropriate application rate for controlled release fertilisers
(CRF). The aim is to provide sufficient nutrition for strong plant
performance while minimising nutrient loss into irrigation/
stormwater run-off. As such, fertiliser rates are usually significantly
lower than those recommended for garden or container plants.
Where the plantings are limited to succulents there may not be
any ongoing addition of fertiliser.
Visual inspection plays an important part in determining whether

plants are experiencing nutrient deficiencies (see Growing Media
for Ornamental Plants and Turf for further information).
CRF is the most suitable choice for plant nutrition in green roof
settings or green facades in containers. The fertiliser comes in
the form of water permeable resin granules or beads and is
applied on the substrate surface but should be raked or mixed
through, ensuring an even distribution. Each rain or irrigation event
dissolves a small amount of the inorganic nutrients stored in the
bead. If the roof or container is being irrigated from below (a subirrigation system) then it is important to mix the fertiliser well into
the substrate.
The elevated temperatures on a roof or facade can lead to
excessive fertiliser loss and damage plant growth. For Australian
natives on green roofs, low phosphorus CRF can be used at half to
quarter of the rate recommended for garden or container plants.
Liquid fertilisers are not suitable for routine use on green roofs,
as nutrients are more likely to leach out of the mix and leave via
stormwater run-off.
Monitoring of fertiliser levels

It is useful to undertake soil testing of pH and electrical
conductivity to establish the conditions under which plants were
started. Ongoing, strong plant growth and coverage is the best
sign that growing conditions are suitable. As long as there are no
problems with the performance of the plants, the manufacturers
recommendations for rate and frequency of fertiliser application
may be followed. If plants do not perform well, or there are any
signs of nutrient deficiency, a sample of growing substrate should
be collected for testing of pH and electrical conductivity (EC) or
total dissolved solids (TDS), following the same test procedure
as was used at planting. Additional fertiliser should be added
if EC or TDS results suggest nutrient levels are simply running
low. If possible this should be incorporated through the growing
substrate to ensure its even distribution, though this may be
difficult to achieve for green facade containers installed at elevation.
This guide has been developed

in collaboration with government,
industry and universities. It provides
advice specific to conditions in
Victoria, Australia. It is hoped that
this guide will help to increase
the number of high quality,
multifunctional green roofs, walls
and facades to make our cities
more liveable and sustainable.
Internal green wall at Mider Investments, South Melbourne, Image: Fytogreen
SECTION
04
Victorian
Case Studies
100
Case Study
Location
JJ Holland Park 85 Kensington
Road, Kensington,Victoria
Completion Date
September 2010
(remediation works July 2013)
Cost
$123,000
Area
The Venny Green Roof

Description
Introduction
The Venny green roof comprises a lower

flat roof, with planting designed around
three sections A, B, and C (Figure 1)
and an upper, sloping green (roof D),
a later addition to the original brief. The
green roof can be viewed from the ground,
access is only available for maintenance.
The upper roof contains an array of
photovoltaic cells (44m2), two solar hot
water panels and a roof ventilator, leaving
approximately 46m2 for planting.
The Venny is a community facility for

children from the Melbourne suburb of
Kensington and surrounding neighbourhoods.
Design of The Venny was commissioned
by the City of Melbourne, incorporating
the use of recycled shipping containers.
As protection was needed to insulate
the spaces below the metal containers,
a green roof was suggested as the most
appropriate solution. It was also anticipated
that the roof would expand the local
knowledge of green roof design, installation
and maintenance at a residential scale.
Figure 1: Schematic plan view of the Venny roof
108m2 lower roof, 103m2 upper

roof on a new building
The project was a joint venture between

the City of Melbourne, The University
of Melbourne and Melbourne Water. The
roof has also been a research site for The
University of Melbourne, with funding
provided through the Australian Research
Council.
Detailed design of the lower areas was
undertaken by The University of Melbourne
and the upper green roof was designed by
Junglefy Pty Ltd.
101
Case Study
Design and components
Maintenance
A ZinCo system was used for the

waterproofing and drainage components.
A low cost membrane material, Volclay
Swelltite, was used. The lower green
roof comprises a ZinCo system, including
a 25 mm drainage cell, and two different
mineral-based substrates developed by The
University of Melbourne. The upper roof
used an alternative system incorporating
a basal protection layer with irrigation
(capillary irrigation matting) and, originally, a
100 per cent coir media at 100 mm depth.
Galaku erosion control netting was used to
hold the plants in place on the upper roof.
Management and maintenance was

considered in the initial design, and a safe
maintenance access point was important.
A lockable alcove was designed with
a purpose-built ladder and signage to
comply with occupational health and safety
standards. Paths of chipped recycled brick
were incorporated into the initial design
of the lower roof to minimise the impact
of maintenance and research activities on
plants and green roof infrastructure. These
factors, combined with the specific species
selection of drought tolerant plants and a
close planting design, were considered to
culminate in a green roof that could be
safely managed, with low impact, and low
maintenance requirements.
Plants for the green roofs were researched

and selected by The University of
Melbourne, based around aesthetic
properties, drought tolerance and low
resource inputs (water, fertiliser and
maintenance). Most were succulents,
particularly sedums, aloes and related
species. They were planted at high densities
to provide rapid cover and discourage
weed infestation.
The upper roof has been designed to
hold a green roof with a saturated load
of 160kg/m2 (including all plants, substrate,
irrigation system and waterproofing). In
addition to the 160kg/m2 there has been an
additional live load allowance of 40kg/m2.
The first two years of maintenance and

management was undertaken by The
University of Melbourne, as part of its
research studies, and Junglefy Pty Ltd. A
comprehensive management plan was
devised by The University of Melbourne
and handed over to the City of Melbourne.
This was the first green roof that the City
of Melbournes landscape maintenance
team had experienced and some problems
did occur when the irrigation system failed
over summer. The maintenance visits also
became infrequent which meant that
the health of some of the species was
compromised. After approximately six
months maintenance by the City of
Melbourne the roof was evaluated and
it was determined that while the lower
green roof was satisfactory, the upper roof
had not performed well. The coir growing

media failed to support plants adequately
the only surviving species had drifted to the
base of the roof slope. While disappointing,
the substrate was used as a trial and the
substrate and plant replacement was not
an unexpected expense for the project.
Remediation of the upper green roof
took place in July 2013. The University of
Melbourne was contracted to develop a
lightweight, mineral substrate and complete
a planting design. Junglefy were re-engaged
to take the lead in the remediation works
including the removal and replacement
of the growing medium and the installation
of new plants.
New ZinCo products, specifically designed
for sloped roofs, were used, a back to base
alarm system for monitoring irrigation
was installed, and Junglefy has continued
ongoing maintenance of this space.
Roof A was planted with a mix of Australian and exotic herbaceous and succulent plant species
Plant species used on the

upper roof 2010
Lampranthus deltoides
Sedum xrubrotinctum
Sedum mexicanum
Sedum pachyphyllum
Sedum reflexum
102
Case Study
Costs - lower green roof
Costs - upper green roof
The lower green roof cost $69,070.

Specific costs of project components are
shown in the table.
The upper green roof cost $11,000,

including the waterproofing layer, growing
substrate, irrigation, plants and planting,
labour and materials.
Component
Cost
Shipping container
steel frame
Recycled
Drain pipe system
$5,000
Bentonite Liner
$16,000
Concrete Screen
$18,000
Zinco System
(Supply)
$7,150
Zinco System (Install)
$1,360
KISSS Below Flow

Flat irrigation and
associated controls
$6,330
Substrate growing
median & crushed
brick paths
$5,900
Coir Mulch Matting
$1,270
Plants (Supply)
$4,520
Plants (Install)
$3,540
Note: it would be unrealistic to expect

to replicate such a build for the same
price today. Junglefys involvement in
construction was undertaken at cost due
to its interest in developing this industry.
Remediation works in 2013 cost
approximately $43,000.
Results and reflections
The Venny has proven to be a pioneering

project that has provided a valuable
learning experience for the emerging
green roof industry. Those involved in
similar projects should invest in good
materials for waterproofing and drainage,
as well as consulting those with expertise
in design and application to ensure plants
are appropriate for the type of roof.
A consistent message in the reflections of
The Venny green roof partners was that
patience is required when undertaking
something that is untested: it is a collaborative
learning process through all stages from
design through to management.
According to The Venny manager, the

roof adds environmental, educational and
economic benefits to the building. As a
small-scale building the design could be
applied in a residential context.
Lessons learned included that:

the bentonite liner and concrete screed

on the lower roof, expensive items
which did not live up to expectation,
would be avoided in future
the use of 100 per cent coir as a
substrate on the upper roof would
be avoided (this was addressed in the
remediation)
the slope called for a water retention
layer (this was added in the
remediation in 2013).
Mixed plantings and non-vegetated zones on The Venny roof
Sedum xrubrotinctum surrounded by the larger, spreading

Carpobrotus modestus
103
Case Study
Location
8-10 Kavanagh Street,
Southbank,Victoria
Completion Date
2009
Cost
$350,000
Area
206m2 on a new building
The Triptych Green Wall

Description
Triptych Apartments include a large
hydroponic green wall on the buildings
exterior south-east facade, extending up
from the second level, above the footpath.
It is visible to all vehicular and pedestrian
passers-by, and is viewed by neighbouring
office and apartment buildings.
Introduction
Visible from the street, the green wall
feature was considered by the developer to
provide a wow-factor, setting the building
apart from other inner-city residences and
blending in with the leafy streetscape.
The purpose of the green wall was to:

obscure the view of the exterior of

the multi-level parking area
use foliage to soften the built
environment
provide habitat and increase diversity
through the use of native and exotic
plant species
utilise collected rainwater
The property was owned by the Stable

Group, and the project was completed by
Nettletontribe architects and green wall
specialists, Fytogreen.
Fytogreens concept drawing shows the arrangement of species in

swathes across the Triptych green wall

The wall includes 362 planting panels
measuring 100 cm x 500 cm x 15 cm
along with 44 planting panels measuring
75 cm x 50 cm x 15 cm. It is designed for
a weight loading of 80kg/m2 dead load.
A spray-on waterproofing material was
used. A root barrier layer was not required
because the air barrier between the wall
and the modular system allows for air
pruning. (Roots become exposed to the
air, which dehydrates them and stops
them growing further.) Polyurethane foam,
a Fytogreen patented product, with felt
wrapping was used as the growing medium.
The foam modules are held in a steel cage,
mounted on a wall using steel brackets.
This view of the established green wall shows how the concept was
translated into a lush, vegetated space
104
Case Study
Plant species used
Dianella Little Jess

Dianella Emerald Arch
Dianella Breeze
Lomandra Tanika
Lomandra Wingarra
Viola hederacea Native Violet
Rumohra adiantiformis Leatherleaf Fern
Nephrolepis obliterata Sword Fern
Asplenium bulbiferum
Mother Spleenwort
Correa Dusky Bells
Ficinia nodosa Knobby Club Rush
Orthrosanthus multiflorus Morning Iris
Campanula poscharskyana Serbian
Bellflower
Liriope muscari Evergreen Giant
Plectranthus ciliatus Spurflower
Aristea ecklonii Blue Star
Pachysandra terminalis Green Carpet
Sarcococca confusa Sweet Box
Liriope spicata Lilyturf
Arthropodium Parnell
Arthropodium Te Puna
Davalia tyermanii Bears Paw Fern
Schefflera aboricola
Dwarf Umbrella Tree
Strobilanthes anisophyllus Goldfussia
Erigeron karvinskianus Seaside Daisy
Plants are irrigated using a controlled

release dripper system that runs to each
separate module, using collected rainwater
supplemented with mains water as
required. Fertiliser is also delivered via the
irrigation drip system. The stainless steel
facia surrounding each panel guides any
excess moisture to a steel drip tray at the
base of the vertical garden.
Irrigation equipment includes a controller
for timed irrigation cycles; a fertigation
system for controlled fertiliser dosing
through the irrigation system; water meter;
pressure gauge; controlled volume drip
irrigation line; and water storage tanks,
filters and pumps.
Native and exotic plant species, chosen for
aesthetic appeal, durability and biodiversity,
are featured. The planting plan considered
the differing levels of sun and shade across
the wall surface, and the impact of plants
shading one another as they grew. At 15
plants per panel, a total of 5,958 plants was
required. For the planting stock, 140 mm
container specimens were grown in an
offsite greenhouse for eight to 12 weeks
before installation. The benefit of using
fully-grown plants is the immediate visual
impact when installed.
The swathes (planted sections of different
species) were specifically designed to
control lateral wind movement over the
host wall surface, either mitigating wind
damage or creating niches for species in
the leeward sides.
In addition to aesthetic appeal, plant
species were chosen to be hardy, low
maintenance and shade tolerant. Many
Acorus gramineus Green Acorus

Rosmarinus officinalis horizontalis
Prostrate Rosemary
Chlorophytum variegatum Spider Plant
Cerastium tomentosum
Snow-in-summer
Escallonia Newport Dwarf
Euphorbia Chameleon
Euphorbia Blackbird
Viola odorata Sweet Violet
The initial planning sketch by Fytogreen
of the species feature coloured foliage or

flowers throughout the year, contributing
to the beauty of the design.
Careful consideration was given to the
combination of species used, and their
placement in relation to each other. All
species were selected to offer cumulative
control of pests and disease spread,
wind, light and moisture, and to manage
competition between species. The longterm growth patterns and likely reaction
to the environment were also considered.
High foliage coverage was sought for visual
appeal and also to out-compete weeds.
Maintenance
By choosing species that respond well to
each other, the green wall requires less
maintenance than a more rigid design. The
owners favoured this approach because
it offered a long-term, adaptable and
sustainable solution.
Fytogreen is contracted to undertake the
maintenance. Maintenance is moderately
fluid, pending seasonal changes and the
clients aesthetic expectations. The Triptych
owners embraced natural aesthetic forms
and ongoing species self-adjusting, leading
to a less restrictive maintenance process.
Knuckle Boom lift access, requiring a
small team of horticulturists, is generally
conducted every three months.
Monthly checks, conducted by one person,
assess water supply, quality and general
garden condition.
105
Case Study
Cost
The green wall project cost $350,000.

This budget included a 12-month contract
with Fytogreen covering maintenance of
the green wall and defects liability. After
this time, the maintenance contracts were
negotiated between the parties and open
for tender.
Fytogreen reports that this is a statement

green wall that has proven to be functional
in terms of water usage, visual impact and
has assisted with the selling of apartments.
Using harvested rainwater from the
building the plants are thriving and habitat
is being created. Fytogreen notes the
visual amenity provided to all surrounding
parties, including passers-by.
The green wall at Triptych adds another element to the street level vegetation
Images courtesy of Fytgreen
In retrospect Fytogreen states it would

have changed only one thing, and that
was to have set up the wall to also be a
research space for vertical garden species.
Fytogreen concludes that this is a largescale green wall that puts Melbourne on
the map. As it is free to view to all passersby it provides inspiration to all to question
technology, property value and the impacts
of vegetation on built surfaces.
106
Case Study
Location
RMIT University city campus
124 La Trobe Street, Melbourne,
Victoria
Completion Date
2011
Cost
$230,000
RMIT University
Building 21 Green Facade
Description
The green facade was constructed on the

north and west-facing external walls of
Building 21, a 60-year-old brick building.
Planter boxes at the base of the facade
support plants that climb up a trellis
stretching the height of the wall. The wall
can be viewed by the general public and is
mostly seen by RMIT students and staff.
The facade includes the following elements:
Introduction
The RMIT University city campus in
Melbourne is a publicly accessible space
made up of historical and modern
buildings, interspersed with functional open
areas. With the completion of University
Lawn Precinct and the refurbishment of all
of the surrounding buildings, Building 21
needed a facelift as the last piece in the
precinct. A green facade was constructed
on the rear of the building.
The Building 21 green facade was a joint
project between RMIT University, Peter
Elliot Architecture and Urban Design,
engineers BHS Consultants, landscape
architects Rush Wright Associates and TJS
Services. The specific facade structure was
provided by Ronstan Tensile Architecture.
Area
122m2 on existing building
a Ronstan X-TEND mesh trellis

system in a diamond-shaped pattern.
The trellis system is secured in place
by steel framing at the top, bottom
and sides of the wall. There is a 40 cm
gap between the trellis system and
the brick facade of the building so no
root barrier or waterproofing layers
were needed
planter boxes, which are mounted
to the existing brick facade using a
galvanised steel frame which encases
the entire planter box. Zinc sheet
vertical cladding covers the front of
the boxes and extends down to hide
the drainage system below
The sides and base of each planter box

are lined with Atlantis 30 mm Flo-Cell
drainage cell and slotted Agridrain Pipe,
and then covered with 2 mm geotextile
Bidim A14G membrane. The bases are
lined with a 40 mm sheet of Hyrdocell
hydro foam.
A drip irrigation system is used, with a slotted
drainage pipe running along inside the base
of the planter boxes to provide drainage.
Hydrocell 40 extensive media, a lightweight
soil mix, was chosen to reduce stress on the
existing brick wall. The substrate was topped
with a 45 mm thick stone mulch layer to
provide protection from the elements.
1 Pre-construction
2 8 months post-construction
3 26 months post-construction
Images courtesy Ronstan
Tensile Architecture
107
Forty-nine individual 140 mm plants,

Kennedia rubicunda (Dusky Coral Pea),
were installed in the planter boxes.
Temporary bamboo supports were used
to help the plants grow up and onto the
trellis. Plastic clips were used at intervals of
40 cm to secure the climber to the trellis.
Provided by Ronstan, the clips are designed
to allow for the plants growth.
Maintenance
The design of the green facade included
maintenance requirements. The site can be
accessed with an elevated work platform.
The planter boxes are raised above
pedestrian level, but are low enough to be
accessed using a ladder.
The green facade requires a moderate
level of maintenance, contracted to the
universitys general landscaping contractor.
Regular maintenance tasks include:

Case Study
monthly inspection of irrigation

system function
twice yearly (spring and autumn)
pruning and retraining climbers
around windows
twice yearly (spring and autumn)
fertilisation, plus additional if required
monthly comprehensive visual
inspection
weekly general inspections (including
removal of rubbish)
Cost
The project cost $230,000, excluding
ongoing maintenance. Specific costs
of project components are detailed in
the table.

The architect believes that the building
now sits comfortably as a backdrop to
the University Lawn Precinct, with the
creeper-covered walls meshing into the
urban landscape. He notes the appearance
of the building has been successfully
transformed through the softening effect
of the creeper-covered wall. Initial plant
growth has exceeded expectations but will
need to be monitored to be maintained
into the future.
Item
Cost
Planter boxes
$80,000
Plants and substrate
$25,000
Plumbing and
irrigation
$25,000
Trellis system
$90,000
Access
equipment hire
$10,000
The ongoing level of required maintenance

can be carried out as part of general RMIT
landscaping. RMIT reports that no plants
have been removed or replaced to date,
due to adequate facade coverage.
The green facade is now a key element of the view from the University Lawn Precinct
108
Case Study
Location
Freshwater Place Apartments 1
Queensbridge Square, Southbank,
Victoria
Completion Date
2004
Cost
Undisclosed
Area
Freshwater Place Green Roof

Description
The green roof is an elevated landscape
located on top of the nine-storey car park.
It is made up of a series of garden mounds,
a grass lawn, storage sheds and planter
boxes for growing vegetables. A windbreak
wall was added to protect the site from
the strong southerly wind.
Introduction
Freshwater Place is a residential complex
containing 534 apartments, located on the
Southbank side of Melbournes Yarra River.
The aim of the project was to provide
residents with a functional outdoor space
that would enhance their inner-city lifestyle
and add value to the property. The green
roof is part of the communal facilities,
which include barbeque areas, pool, gym
and function spaces. Residents and their
guests have full access to the level 10

roof and it can be seen from most of the
apartments as they extend many floors
higher than the car park. Maintaining the
green roof s aesthetic appeal is the priority
for all maintenance activities.
The green roof was a collaborative
project between Bates Smart Architects,
Australand and Laurence Blyton Landscape
Architects. The green roof components
were installed by Fytogreen and are
maintained by Facility Management Victoria.

The roof was installed using the following
layers:

waterproofing spray-on layer, installed

by JA Dodds
waterproofing protection layer, lowdensity polyethylene (LDPE) foam
Flo-Cell drainage layer

Bidim geotextile layer
Fytogreen Hydrofoam hard foam
RG30
growing substrate
Vegetable planter boxes, provided by the

Little Veggie Patch Co, are made from
recycled apple crates. Measuring 1.2 m
along each side, and about 80 cm tall, the
boxes are anticipated to last more than 10
years. The vegetable crates are located on
the west side of the site and receive less
sunlight than the other sections of the roof.
There are 30 established trees growing in
the green roof garden beds, surrounded by
a range of shorter shrubs. The substrate in
these beds is 70 cm deep to accommodate
the trees root systems. Comparatively, the
substrate under the large lawn area is only 35
cm deep.The substrate mix used throughout
the site was prescribed by Fytogreen, and
109
Case Study
is made up of sand, organic material and

water retention flakes. A river stone mulch
layer sits on top of the substrate to reduce
evaporation, reduce weed growth and
stabilise the soil in the wind.
There is a mix of permanent green
elements, seasonal interest from foliage
and colourful flowers. There is also one
lemon tree on the roof, after a request
by a resident that it be planted. It is yet to
fruit, but is growing well.
Replacement species have been selected
from existing plants that have grown well.
The specific plant species used on the
Freshwater Place green roof are listed
in the table to the side. All species are
low maintenance, can be grown in most
climates and soils, are tolerant of drought
and wind, and prefer to be grown in full sun
to part shade. They can be grown in urban
areas where pollution levels may be high.
The green roof drains into a 160,000-litre
storage tank that sits beneath the paved
area. Rainwater is also collected into this
tank from other building surfaces. The
collected water is used for irrigating the
garden and can sustain the plants for up to
three weeks in the height of summer, and
as a result, potable water is rarely used.
A drip irrigation system was installed

beneath the substrate in the garden beds
as part of the initial construction, but this
system is no longer used. Although it was
functioning correctly, the system did not
allow for the different water requirements
of trees and other plants. In 2010, the
maintenance team installed separate drip
irrigation systems for the trees and shrubs,
which run along the surface of the soil.
The grass lawn is watered using automated
sprinklers.
The plants are monitored daily to ensure
that the irrigation is sufficient and to
identify problems before the plants
showed signs of distress.
In the initial design, five round plant rooms
on the roof were topped with vegetation
to provide residents in the apartments
above with a consistent green outlook
onto the green roof. Sloped at a slight
angle to allow for drainage, these roofs
were planted with succulents in a shallow
substrate made of fine stone aggregate.
Parts of these roofs became waterlogged
and caused some plants to fail, resulting in
patchy green coverage when viewed from
above (see image). Although the drainage
could have been repaired and the roofs
replanted, maintenance staff chose to not
replace the plants, leaving the area with
just the stones. This decision was made to
ensure that the residents had a pleasing
outlook onto the roof at all times.
Plant species used
Pyrus ussuriensis
Manchurian Pear cultivar
Dianella Little Jess
Juniperus sabina Savin Juniper
Liriope cultivars Lily Turf
Viola hederacea Native Violet
Viola labradorica Labrador Violet
Ixia cultivars Corn Lily
Ipheion uniflorum Spring Star
Freesia cultivars
Iris cultivars
Rahiolepis umbellata Yeddo Hawthorn
Pennisetum clandestinum Kikuyu
Trachelospermum jasminoides
Star Jasmine
Aerial view of the Freshwater Place green roof

after construction
110
Case Study
Maintenance
Although the green roof at Freshwater
Place has been designed to minimise
maintenance, there are ongoing challenges.
A different level of maintenance is required
for the intensive garden beds and the
extensive lawn area. For an annual fee of
$25,000, the maintenance is carried out
under contract and includes replacement
of plants. Maintenance activities include:
Irrigation
Three times per

week in summer;
varies for the
shrubs and trees.
Pruning
Annually for trees;

shrubs as required
Plant
evaluation
Weekly
Lawn
mowing
Weekly in spring;
fortnightly at other
times
Scarifying
the grass
Every three years
Fertilising
Monthly for turf;

plants every six
months; annually
for trees
Plant
renewal
As required
in winter
Cleaning &
monitoring
of hard
landscape
elements:
Weekly
Inspection
of irrigation
system
function:
Daily in summer,
monthly at other
times
A key challenge for maintaining the

green roof has been ensuring that plants
get enough water to maintain optimum
growth and to look healthy and visually
appealing. This requires regular monitoring,
so it is important that the maintenance
contractor understands the environment
and how it can change very quickly.
Originally, Tall Fescue grass was used as
lawn cover, but the maintenance team
found it difficult to keep it looking good
through water restrictions and the hot
summer months. At times security staff
hand-watered in summer to keep the
grass green. Following a review of plant
maintenance in 2007, the tall fescue was
replaced with Kikuyu grass, a species with
lower water requirements, and it has been
very successful.
Exposure to the elements has also been a
challenge, particularly for the maintenance
of the large Manchurian Pear trees. The
strong wind has caused them to grow
at an angle, particularly in the older tree
stock, due in part to the use of fully-grown
trees at installation, As a consequence,
the root systems did not establish in the
soil as well as they could had younger
plants been used. Their lack of stability
in the wind required the use of support
cables. Recently, some of these trees were
replaced with younger plants and these
have quickly grown to be equal in size to
the existing trees, and are far more stable.

Overall, the Freshwater Place management
team is extremely happy with the aesthetic
and social benefits of the green roof. The
useability of the space gives the building a
unique edge and adds value to the property.
The green roof is a well used space,
particularly in the warmer months of the
year. The barbeques are in constant use
throughout the summer and the lawn is
a popular place for picnics. The vegetable
gardens are maintained by residents, who
enjoy the social aspect of growing produce
together.
Reflecting on the lessons learned over the last
nine years, the management team has advice
for anyone considering a green roof project:
1.
Green roofs have their own

challenges due to the unusual nature
of the site, so it is best to keep the
design simple.
2.
Green roofs are not set and forget.

It takes some time to get the plants,
irrigation and maintenance right, so
be prepared to make adjustments as
you go along.
3.
Monitoring the green roof

components and plants is essential for
establishing a successful green roof.
The monitoring should be regular and
not reactive.
Maintenance processes are regularly

reviewed to ensure they are consistent
with the desired outcomes.
Manchurian Pear trees are a feature on the Freshwater Place green roof
111
Case Study
Location
290 Belmore Road, Balwyn,Victoria
Completion Date
December 2012
Cost
$306,000
Area
Minifie Park Green Roof

Description
The roof is on a one-storey building in a
park. There is no public access but the roof
slope of 2 to 3 degrees means it can be
viewed from ground level. The green roof
includes a range of indigenous plant species
to promote the use of local flora and
provide habitat opportunities for fauna.
Introduction
Minifie Park Early Learning Centre is a
council-owned, community-operated
childcare centre located in North Balwyn,
an eastern suburb of Melbourne. It was
built to replace an older building.
Council decided to include a green roof
as an integral part of the new facility. The
purpose of the green roof was to provide
thermal insulation and help the building
blend in to the surrounding parkland.
The project received funding from

Melbourne Water and the Victorian
Adaptation and Sustainability Partnership to
support the incorporation of water sensitive
urban design features into the building.
The building was designed by the
architectural firm FMSA and built by
Behmer and Wright. The green roof was
designed and constructed by Junglefy.

The roof has a weight loading of 170 kg/m2.
A gutter guard has been installed in the box
drains, and leaf traps in downpipes to prevent
them from blockage by pine needles from
an overhanging tree. There is 400 mm wide
unplanted perimeter zone to keep the areas
around drains clear of vegetation.
Kalzip aluminium standing seam roof
sheeting was used for the roof deck. It
The building sits low in a park, meaning the roof can be easily viewed from street level
was installed over a steel-framed portal

structure a building frame with pitched
rafters. The standing seam system was a
key element in Junglefys tender for the
work, because its successful use on green
roofs is well documented, and Kalzip was
prepared to provide a 10-year warranty
on the waterproofing. This is the first
Australian green roof installed over this
type of lightweight roofing system to
Junglefys knowledge. The Kalzip roof
system is intrinsically watertight so a
waterproofing layer or protection layers
were not installed.
The drainage layer was ZinCo FD40, with
water-retention capacity. A ZinCo Filter
Sheet SF was also installed.
The growing substrate was Junglefys
proprietary Victorian mineral mix. It was
delivered in 5,000 kg capacity bags, lifted
by crane and installed through a hose
112
Case Study
attachment, and applied 100 mm deep.

The large single substrate bag could
be moved around the roof and greatly
reduced the installation time compared to
using multiple smaller bags. The substrate
was covered with a layer of jute netting
to provide weed control and protection
from slipping due to gravity and wind
forces. Plants were installed through cuts
made in the netting. A layer of substrate
was installed over the top to reduce the
potential for wind uplift.
The Early Learning Centre has an additional
bare roof area of approximately 300 m2.
The green roof is irrigated with water
collected over all roofs. Captured water
is stored in an interconnected network of
six tanks, with a total capacity of 24,000
litres, in the ground level plant room at the
lowest point of the building. The modular
tank system offers adaptability for current
and future use: one or more tanks can be
removed for repair or replacement without
any need to interfere with the building
structure and surrounds.
The irrigation system has back to base
control with sensor-driven monitoring
from an inbuilt weather station enabling
irrigation cycles to be missed during rain
events exceeding a specified threshold.
The system used is standard for parks and
gardens irrigation throughout Boroondara.
Water is pumped up to the roof from
ground level and delivered to the plants
through a KISSS Below Flow Flat capillary
system. Initially, irrigation delivery was
patchy across the roof causing uneven
plant performance and the loss of a small
number of plants, but adjustments to the
system have resolved this issue.
The plant palette was a mix of lowgrowing Victorian perennial grass and herb
species typically found in grassy/creek-line
woodland (the likely original vegetation on
this site). The herbs flower in spring and
autumn, providing colour interest through
a significant part of the year. Proposed
additions include the planting of taller
grasses to conceal the ventilation shafts.
Junglefys custom-designed aluminium edge
restraints separated vegetated and nonvegetated areas of the roof.
Planting stock was contract-grown by

Australian Ecosystems, provided as
tubestock, and inspected at the nursery
prior to delivery. Planting took place in
November, after a delay. As a result, handwatering was necessary over summer, to
ensure the plants were well established.
Maintenance
Junglefy has maintained the roof since
planting. The intention had been that
roof management would move to the
City of Boroondara. However, due to
Junglefys experienced management and
competency to work at heights, they
have been sub-contracted by the Citys
Parks and Gardens team, and continue
to maintain the green roof on a monthly
basis. This arrangement has simplified
management for the City of Boroondara.
The potential for acidification of the growing
medium from the needles shed by a nearby
overhanging pine tree is a source for concern.
Performance evaluation of the green roof
plantings is being undertaken by the City
of Boroondara.
Plant nutrition is provided as eight to
nine-month low phosphorus controlledrelease fertiliser applied at half the
recommended rate.
Costs
Total cost was $306,000. This included:

design and preliminaries

$180,000
green roof installation and plants
$126,000
The total building cost was $3.5M.
Results and reflection

Insulation properties were a major driver
for the inclusion of a green roof in the
building design. An anecdotal story from
builder Behmer and Wrights site manager
suggests that the green roof contributes to
thermal comfort for users: after the green
roof substrate was installed in winter, the
builders elected to spend their lunchtimes
in the facility as they found it was warmer
than the site office.
Monitoring of energy consumption for

heating and cooling will reveal whether
usage is lower than would be predicted for
a building of this type without a green roof.
The City of Boroondara and the users
of the Minifie Park Early Learning Centre
feel very proud of the redevelopment and
its green roof. The positive experience at
Minifie Park has made Council enthusiastic
to pursue future green roof projects.
Council says that the local community has
responded well to the green roof, seeing
the views of vegetation as far superior to
a bare metal roof. The design objective
to create a connected visual experience
between the building and the park has
been met. The green roof demonstrates
that a modern building development can
be sympathetic to its surroundings.
Plant species used

Austrodanthonia racemosa
Slender Wallaby Grass
Austrodanthonia setacea
Bristly Wallaby Grass
Poa morrisii Velvet Tussock Grass
Poa morrisii Velvet Tussock Grass
Bulbine bulbosa Bulbine Lily
Chrysocephalum apiculatum
Common Everlasting
Chrysocephalum semipapposum
Clustered Everlasting
Dianella revoluta Black-anther Flax Lily
Einadia nutans Nodding Saltbush
Linum marginale Native Flax
113
Case Study
1 Sheets of drainage cells were cut to fit the width of the roof profile. Image: Junglefy
2 The unplanted perimeter zone prevents plant roots from growing into the drainage pipes
3 Native grasses on the green roof blend into the surrounding parklands and provide habitat
114
Case Study
Location
Lower Powlett Road,Wonthaggi,
Victoria
Completion Date
2012
Cost
$4,000,000
Victorian Desalination
Project Green Roof
Description
The Victorian Desalination Project
green roof is the largest in the southern
hemisphere. It covers a number of
buildings of the process plant, ranging
in pitch from 3.5 to 20 degrees. The
undulating slopes of the roof are designed
to limit visibility of the industrial buildings
from the surrounding public areas and link
to the nearby coastal landscape.
Introduction
The Victorian Desalination Plant provides
for desalinated water to be delivered
from the private sector to the State
Government owned water authorities.
The plant is capable of supplying up to 150
billion litres of water a year to Melbourne,
Geelong and via other connections to
South Gippsland towns.
The aesthetic focus of the project was

to soften the visual impact of the process
plant buildings. Several other objectives
were also considered in design of the
green roof, including, ecological restoration
of the area, thermal performance of the
building, minimising the noise impacts
from the desalination process plant and
protection of the roof from the harmful
effects of solar radiation.
The Victorian Governments private
sector partner, AquaSure, consists
of Suez Environnement, Degremont,
Thiess and Macquare Capital Group.
The Theiss Degremont Joint Venture
was the design and construct contractor
for AquaSure. The green roof design
delivery was provided by ASPECT Studios,
with technical design, installation and
maintenance by Fytogreen.
Graphic depiction of the design shows how the green roof blends into the surrounding environment
Area
26,000m2 on a new building

With a saturated dead load of 143kg/
m2 plus live load, the roof is designed for
maintenance access only.
The building is a steel frame structure with
a timber ply roof deck. Waterproofing layer
is Sika Sarnafil. A foam resin developed
by Fytogreen was used as an underlay,
trapping water and nutrients and helping
the plants to grow. The drainage layer is a
20 mm Atlantis Flo-Cell with a Bidim
A14 geofabric to filter sediment run-off.
The extensive green roof substrate mix
was provided by Fytogreen and installed
to a depth of 80 mm. The majority of the
roof was constructed on a slope of less
than 15 degrees and did not require any
sheer protection. However, about 650 m2
of the roof was installed on slopes greater
than 15 degrees and Geoweb Cellular
Confinement System was used to stabilise
115
Case Study
the substrate and vegetation. The 150 mm

deep Geoweb cells were installed over
four days, with anchoring tendons running
through every second row of cells to
secure the system in place.
Due to the strong winds to which the
green roof is exposed, a system of stainless
steel hold-down netting was required in
the areas subjected to the highest wind
speeds. These winds create a twin vortex
effect where the combined lateral forces
and vertical uplift would risk dislodging the
substrate ballast layer. The primary function
of the mesh was to mitigate the insurance
risk during establishment when the mulch
layer was exposed. As time goes on it is
expected that the plants will ameliorate
wind uplift.
A sub-soil irrigation system was designed
for the green roof by Netafim and
installed by Fytogreen. The automatic drip
system includes a weather monitoring
station to ensure irrigation frequency and
volume is appropriate. Data is collected
on the amount of rainfall and the level of
evaporation. Water for irrigation is captured
from a 3.7 ha collection area and stored
in a 0.5 megalitre pond. In addition to the
captured storm water, 600 litres of process
sampling water per hour is available from
the desalination process plant.
The Fytogreen design for the green
roof was carefully considered to ensure
consistency with the coastal character, and
to meet the ecological objectives of the
project. Species selection focused on plants
that are locally indigenous to the area using
seed that was collected within 40 km of
the site.
Given the sites exposure to the elements

in a windy and temperate coastal
environment, testing was undertaken prior
to construction to ensure that the species
chosen would thrive in the conditions.
Fytogreen established a test roof on a
nearby site in 2009 to determine which
species would respond well to the wind
and variable temperatures, and to test
planting patterns that would enhance the
health of the plants.
Plants are fertilised using Osmocote low
phosphorus 12 to 14-month controlled
release fertiliser. Application rates are
adjusted as deemed necessary.
Maintenance
Fytogreen has a five-year contract to carry
out any maintenance required for the
green roof. Given the high profile of the
project and the community expectations
around aesthetics, the contract specifies
standards for maintenance. This includes a
requirement that vegetation cover must be
at least 95 per cent, with no more than five
per cent weeds. Fytogreen visits the site
as required, to ensure these maintenance
obligations are met. Visual inspections
of plant health are important to ensure
irrigation and nutrient levels are adequate.
Plant species used
Acaena novae-zelandiae Bidgee-widgee

Actites megalocarpa Dune Thistle
Apium prostrata Sea Celery
Ficinia nodosa Knobby Club-rush
Carpobrotus rossii Pigface
Correa alba White Correa
Correa reflexa Native Fucshia
Dianella admixta Spreading Flax-lily
Dianella brevicaulis Coast Flax-lily
Dichondra repens Kidney Weed
Disphyma crassifolium ssp. clavellatum
Rounded Noon-flower
Gonocarpus tetragynus
Common Raspwort
Goodenia ovata Hop Goodenia
Lomandra longifolia Basket Grass
Olearia axillaris Coastal Daisybush
Rhagodia candolleana ssp. candolleana
Seaberry Saltbush
Senecio spathulatus Dune Groundsel
Stylidium graminifolium
Grass Triggerplant
Tetragonia implexicoma Bower Spinach
Threlkeldia diffusa Coastal Bonefruit
Ozothamnus turbinatus
Coast Everlasting
Chrysocephallum apiculatum
Common Everlasting
116
Case Study

The opportunity to develop an indigenous
plant palette for such a large scale green
roof has demonstrated the way the natural
ecology evolves and responds to the
site conditions and the development of
microclimates as the vegetation matures.
Some of the initial planting stock struggled
to survive the windy conditions on-site.
However, Fytogreen anticipates that the
existing vegetation will provide protection
for new plants that grow from self-sown
seed, allowing them to establish more
strongly on the roof.
Fytogreen points out that the

requirement for irrigation water should
not be underestimated, and it is important
to be mindful of the clients expectations
in terms of the roof s appearance. The
aesthetic value may become a higher
priority than designing for minimum
water use. Recovery of irrigation run-off
enables 80 per cent of the water to be
re-used and ensures that water sensitive
design principles are maintained without
compromising plant performance and
appearance.
The vast size of the green roof planted
with Australian natives leaves a positive
impression with all visitors to the site.
The inclusion of the green roof on the

Victorian Desalination Project was
an inspired gesture that added to the
acceptance of the project by the local
community and the wider public.
ASPECT Studios reflects that because
this roof was constructed in the absence
of a formed Australian green roof design
standard it is a testament to the innovation
and skill of the design and construction
team. Initially viewed as a risk, the green
roof has proven to be one of the most
successful elements of this challenging
project and represents the growth of the
green roof industry in Victoria.
1 Irrigation pipes are embedded in the upper level of the growing media, above filter sheet and drainage layers
2 Plants were propagated offsite and delivered to the green roof for installation
3 Plants were well established by December 2013
4 Non-vegetated zone around the edge of the roof
All images in this case study are courtesy of ASPECT Studios and Fytogreen
117
Case Study
Location
Burnley Campus,The University of
Melbourne , 500 Yarra Boulevard,
Richmond,Victoria
Completion Date
February 2013
Cost
$13, 930
Burnley Biodiversity
Green Roof
Description
The green roof is located above ground
floor offices on a concrete roof deck with
a 1 degree slope. The roof is accessible
only to authorised staff or students with
Working at Heights certification; however,
it can be viewed from the first floor
hallway window.
The Biodiversity Green Roof features:

Victorian grassland plant species

in a shallow scoria-based growing
substrate
a range of landscaping materials
(sand, gravel, ash, rubble) and features
(logs, rocks, hollow twigs, roof tiles,
terracotta pots) to create habitat
opportunities for birds, lizards, insects
and other invertebrates
a small ephemeral pond and shallow
creek bed, that are supplied by rainfall
run-off from the roof above
Introduction
The University of Melbourne has a campus
in Richmond, near the Yarra River, focusing
on horticultural research and education.
The main building was constructed
between 1946 and 1949 and is protected
by a Heritage Overlay, and the entire site is
listed on the Victorian Heritage Register.
The northern end of the roof of the
main building has been developed into
a Biodiversity Green Roof as part of the
larger scale Green Roofs Project, which

also includes a Demonstration Roof and
a Research Roof on the same building. A
design team from HASSELL worked with
the University to provide design solutions
to assemble the roofs. Junglefy constructed
the roofs. A planning consultant was hired
to navigate through the planning process
and clarify which permits were required.
The Biodiversity Green Roof was
developed as a part of the larger Burnley
Green Roofs Project to encompass
demonstration, education, extension and
research. The Biodiversity Green Roof
provides students and visitors to the
University with an example of the design
and features of a non-irrigated, shallow
depth green roof designed for habitat.

The roof has a weight loading of 150 kg/m2.
Replacement of waterproofing was
avoided by patch repair of existing
waterproofing: the estimated cost saving
was $2,000. Components include ZinCo
SSM45 protection mat and high-density
polyethylene (HDPE) root barrier, a ZinCo
FD40 drainage layer and ZinCo Filter
Sheet SF. A scoria-based growing substrate
was delivered by crane in 1 m3 bulker bags,
and installed to a depth of 100 mm.
A 400 mm wide unplanted perimeter
zone keeps the area around the edge of
the roof clear. Aluminium edge restraints
Area
49m2 on an existing building with
heritage considerations
separate vegetated and non-vegetated

areas of the roof. Scoria aggregate was
installed in the non-vegetated areas of the
green roof.
The Biodiversity Roof receives run-off
from two downpipes that drain the roof
area above it. One is directed into the
pond and ephemeral stream, the other
enters a buried drain pipe that travels
along the long axis of the roof. This allows
lateral seepage of water into the substrate,
and supports plant species with higher
water needs, such as Kangaroo Grass
(Themeda triandra). Drainage off the roof
is achieved through two drains on the
northern perimeter of the building.
There is no irrigation system on the
Biodiversity Roof. It is watered infrequently
by hand-held hose during hot weather or
prolonged periods without rain.
The plant palette consists of Victorian
perennial grasses, herbs, and one species
each of an orchid and a fern. These
species are typically found in grassland
and woodland, and some are known
sources of food and nectar for insects.
Plants provide colour and interest through
a significant part of the year. Tubestock
(grown in the Burnley campus nursery,
with a small number of plants purchased
from Victorian indigenous nurseries) was
planted in February 2013. The roof was
hand-watered through autumn to promote
establishment.
118
Case Study
Plant species used

Herbaceous perennial herbs
Grasses and
grass-like forms
Orchid
species
Fern species
Arthropodium milleflorum
Pale Vanilla Lily
Linum marginale
Native Flax
Austrodanthonia carphoides
Short Wallaby-grass
Microtis unifolia
Common
Onion-Orchid
Cheilanthes
austrotenuifolia
Green Rock Fern
Asperula conferta
Common Woodruff
Lobelia pratioides
Poison Lobelia
Austrostipa scabra
Velvet Tussock Grass
Brachyscome basaltica
Swamp Daisy
Marsilea drummondii
Common Nardoo
Chloris truncata
Windmill Grass
Brunonia australis
Blue Pincushion
Microseris lanceolata
Yam Daisy
Dichelachne crinita
Longhair Plumegrass
Bulbine bulbosa
Bulbine Lily
Pelargonium rodneyanum
Magenta Storksbill
Lepidosperma concavum
Sword-sedge
Calocephalus citreus
Lemon Beauty-heads
Podolepis jaceoides
Showy Podolepis
Lomandra filiformis
Wattle Mat-rush
Calotis anthemoides
Cut-leaf Burr-daisy
Ptilotus macrocephalus
Green Pussytails
Themeda triandra
Kangaroo Grass
Chrysocephalum apiculatum
Common Everlasting
Ptilotus macrocephalus
Green Pussytails
Cullen tenax
Emu Foot
Rumex dumosus
Wiry Dock
Dianella revoluta
Black-anther Flax Lily
Rutidosis leptorrynchoides
Button Wrinklewort
Eryngium ovinum
Blue Devil
Selliera radicans
Shiny Swamp-mat
Eryngium vesiculosum
Prickfoot
Senecio quadridentatus
Cotton Fireweed
Helichrysum rutidolepis
Pale Everlasting
Stylidium graminifolium
Grass Trigger-plant
Hypericum gramineum
Small St. Johns Wort
Veronica gracilis
Slender Speedwell
Leptorynchos squamatus
Scaly Buttons
Vittadinia cuneata
Woolly Vittadinia
Leucochrysum albicans var.

tricolor Hoary Sunray
Wahlenbergia communis
Tufted Bluebell
Scaly Buttons
(Leptorhynchos squamatus)
Hoary Sunray (Leucochrysum albicans var. tricolor)
Blue Pincushion (Brunonia australis) with

visiting Hoverfly
119
Case Study
Maintenance
Staff maintain the Biodiversity Green Roof:
this takes about one hour per month. A
photographic record of weed species is
maintained to monitor those that germinate
on the roof. Timely removal of these plants
before they set seed prevents them from
becoming more widespread. Plant nutrition
is provided as eight to nine-month low
phosphorus controlled-release fertiliser,
applied at half the recommended rate.
Component
Cost
Preliminary costs:
design, project
management, etc.
$3,000
Repairs to existing
waterproofing
$1,500
Protection Mat
SSM 45
$250
Root barrier
$100
The following table details outline the

indicative cost of the Biodiversity Green
Roof. As it was installed as part of the
larger Burnley Green Roofs Project, with
works carried out simultaneously (for
example, substrates for all green roofs
were lifted by crane on the same day),
there were economies of scale for design
and installation. However, for this case
study, costs are provided, in the table, for a
stand-alone design and build, as the scale
of this roof was small and simple in relation
to the overall Burnley project.
Aluminium retaining
edge (33 linear m)
$3,580
FD40 drainage
$1,100
Filter Sheet SF
$120
Scoria-based growing
substrate
(10 cm depth)
$680
Scoria aggregate
installed on nonvegetated perimeter
$350
Labour cost of
installation including
crane fees
$1,020
Labour cost of
installation including
crane fees
$630
Plant production/
purchase costs
$600
Materials collection
and planting
$1,000
Costs
Nine months after planting the vegetation

is still quite sparse, although this is likely
to fill in, particularly as the grasses selfsow over time. Plants were grazed by
possums living in a pair of Italian Cypress
trees (Cupressus sempervirens Swanes
Gold) that were growing adjacent to the
building. The trees were removed during
2013 because possum nesting and grazing
caused irreparable damage to the trees
canopies. The rooftop plants recovered
well over spring.
Australian ravens and magpies visit the
roof to bathe in the pond, and also bring
food to consume on the roof. Spiders have
colonised the tree debris, and an ant colony
has moved into the rocky substrate near the
end of the stream. Burnley staff members
have commented on their enjoyment of the
colourful grassland species planted outside
the first floor window.
Kangaroo Grass established strongly

on the Biodiversity Green Roof. Source:
Leanne Hanrahan
Bundles of sticks are installed amongst

the vegetation to provide homes for
native wildlife. Source: Leanne Hanrahan
120
Case Study
Location
Docklands Campus, Kangan
Institute, Harbour Esplanade,
Docklands,Victoria
Completion Date
November 2012
Cost
$56,000
Area
Kangan Institute Green Roof

Description
This water-efficient green roof is designed

as a space to provide amenity for staff.
The area is not open to the general public.
Decking and seating is provided. The roof
is built on a concrete roof deck with 1.5
degree slope, it is above the third storey.
The roof weight loading is 200 kg/m2. Roof

drainage is achieved through a series of infloor sumps, with overflow risers installed
along the bottom of the roof slope.
Introduction
The Kangan Institute Automotive Centre
of Excellence (ACE) is located in the
Batman Hill Precinct of Melbournes
Docklands. The building holds a 5 Star
Green Star rating. The building houses a
2,000 m area of automotive workshops,
and 1,200 m of specialised training and
office areas.
The green roof is located adjacent to the
administrative offices, and over the learning
suites, which will benefit from reduced
heat loads.
The green roof was designed by ASPECT
Studios, in collaboration with Gray Puksand
Architects. Robert Bird Group provided
structural and civil engineering services.
The green roof was installed on the
concrete roof deck of the new concreteframed building.
The drainage layer is Atlantis 20

mm Flo-Cell drainage cell, with flow
across the roof to perimeter drain. The
filter sheet is Bidim geotextile, Grade
A14. For waterproofing, Waterproofing
Technologies Enviro HP1200 was used.
This is a two-component, spray-applied,
flexible polyurethane membrane. A leak
detection system was not installed.
As HP1200 waterproofing treatment
is rated as root-resistant (through a
testing procedure specified and assessed
by CSIRO), a root barrier was not
required. Separation sheets of low-density
polyethylene (LDPE) were installed to
protect the waterproof membrane during
construction.
Stormwater run-off was captured to
irrigate the green roof, as well as toilet
flushing: one point was awarded under
Green Stars WAT-3 criterion for the
required measurable reduction (by 90
per cent) in potable water consumption
on the site from these initiatives.
Fytogreen Australia designed and
installed the irrigation system. Irrigation is

delivered through a Netafim sub-surface
dripper system. This is water-efficient,
programmable and automatic enabling the
duration and frequency of irrigation cycles
to be adjusted.
ASPECT Studios developed the planting
design, which consists of low water use
herbaceous and succulent perennials: all
have performed strongly.
Plant species used
Anigozanthus Ruby Velvet

Carpobrotus edulis
Crassula capitella Campfire
Dianella caerulea Cassa Blue
Dianella caerulea Little Jess
Lomandra longifolia Tanika
Poa poiformis Courtney
Sedum palmeri
121
Case Study
Maintenance
Establishment maintenance was provided

for eight weeks after planting. The green
roof was then managed by the Kangan
Institute maintenance team. Plant nutrition
is provided as 12 to 14-month low
phosphorus controlled-release fertiliser
applied at half the recommended rate.

The garden has suffered somewhat from a
lack of maintenance. A maintenance strategy
is now being developed. Bird control has
been needed as seagulls have been nesting
in the garden after being disrupted from
nesting elsewhere on the building.
1 Roof deck with waterproof membrane prior to flood testing. The raised strip is a major structural movement joint which required specific attention
to maintain waterproofing 2 Views of the green roof at planting 3 Views of the green roof 10 months later 4 Anigozanthos Ruby Velvet
contributes a striking element to the green roof planting scheme at Kangan Institute
All images in this case study are courtesy of ASPECT Studios and Fytogreen
122
Case Study
Location
131 Queen St Melbourne,Victoria
Completion Date
July 2010
Cost
$219,000
Area
200m2 on an existing building
Growing Up Rooftop Garden

Description
The roof space is surrounded by a 1.2 m
high balustrade above the 8th floor of the
building. The rooftop garden total area is
200 m2, with planter boxes occupying 48
m2, and a central hill area of 43.5 m2.
A trafficable zone expands and contracts
around a central landscaped hill to create
a number of gathering spaces of various
scales and orientations. Bound by edges
of seating and planting, inhabitants are
surrounded by greenery.
About half of the 131 Queen Street roof
area is occupied by plant and machinery: this
is screened and separated from the accessible
roof garden area by a picket fence.
An additional 38 m2 green roof space
(not publicly accessible) was installed
above the lift motor room. This is part
of an Australian Research Council
Linkage Project Grant carried out by
The University of Melbournes Green

Infrastructure Research Group, to
investigate the performance of plants
on green roofs in a variety of growing
substrates.
Introduction
131 Queen Street is managed by Quayles
Owners Corporation Managers. The
building was constructed in 1896 and the
tenants include a range of private and
public organisations. It was intended that
the rooftop garden be used by building
tenants for lunch and recreational breaks,
meetings, workshops and classes, as well as
special events.
The Growing Up roof was built after
the Committee for Melbourne ran a
design competition for a green roof. The
Committee identified three potential
CBD rooftops and ran the competition
to demonstrate how a vibrant, innovative
and contemporary urban green space

could be created on a rooftop. Safety,
maintainability, and durability were key
considerations for assessment of entries in
the design competition.
Bent Architecture won the design
competition with its Head for the Hill
submission, based on the roof at 131
Queen Street.
The builder was Better Projects Australia
and engineers were Clive Steele Partners.
The University of Melbourne provided
guidance on substrate and planting design.
The project budget was $200,000, with
additional in-kind support provided by
sponsors; for instance, VicUrban (the State
Governments former development agency,
now Places Victoria) provided a project
manager to oversee construction and
ensure that partners objectives for the
project were met.
Timber decking, mosaic seating and permeable paving treatments are some of the functional and decorative features used
123
Case Study

The roof s weight loading is for a dead
load of 300 kg/m2 and a live load 150 kg/
m2. Total carrying capacity is 100 people.
The weight loading precluded the original
design from being realised, which was
a hill with a large volume of soil and
a mature tree growing on it. Instead a
sculpture tree was constructed, centred
over a column, and covered with wisteria
to provide shade in summer and allow
sun penetration onto the roof in winter.
A hill was made from recycled, expanded
polystyrene covered with a small volume
of substrate and succulents.
Drainage outlets along perimeter walls
lead to concealed downpipes. The roof
deck is steel framed with precast concrete
roof slabs and sand cement screed over to
create fall from the roof to drainage outlets.
A new Polyseal Enviro 800 Pur Top-coat
polyurethane waterproofing membrane
was installed over the existing membrane.
This carries a seven-year warranty.
Elmich VersiCell structural (weight-
bearing) drainage modules were installed

underneath pervious paving material. The
open drainage layer allows free flow of
water through to the waterproofed roof
deck. No changes were made to the preexisting drainage points. ZinCo Filter Sheet
SF was used over the drainage modules.
The growing medium (saturated bulk
density 750 kg/m3) was mixed by Debco
to a recipe specified by The University of
Melbournes Green Infrastructure Research
Group. Growing medium is used at depths
of 200 mm in shallow planter boxes, and
400 mm in deep planter boxes. The same
growing medium is used on the hill at a
depth of 200 mm over most of its face,
although the depth increases to 400 mm
depth at the top and on the western face
of the hill, to allow for the expanding root
system of the Chinese Wisteria. The build
up of the hill is created from recycled
expanded polystyrene blocks, overlaid
with an Elmich VersiWeb 200 mm deep
cellular confinement system to contain the
growing substrate. The hill is covered with
geotextile, and plant root masses were
installed into slits cut into the fabric.
The substrate and plant selection was

made with consideration of the Growing
Up teams desire to install a sustainable
green roof that did not require irrigation.
However, after project handover, the
building owners installed a drip irrigation
system for use particularly during harsh
summer weather conditions. Captured
rainwater is supplied to the productive
garden and perimeter planters, but the hill
zone is flourishing without irrigation.
Plants were supplied in a range of sizes,
from tubestock, and 14 cm through to
30 cm containers from members of the
Nursery and Garden Industry Victoria.
The University of Melbournes Green
Infrastructure Research Group grew most
of the succulent plant species that were
installed as tubestock. A total of 1,664
plants were installed.
1 The Growing Up roof garden at completion

2 Two years later
3 Three years later
Images in this case study courtesy Diana Snape Photography, for Bent Architecture.
124
Case Study
Plant species used

Grass-like
Culinary herbs
Climbers
Succulents
Trees
Shrubs
Lomandra
confertifolia
Little Pal
Origanum vulgare
Oregano
Passiflora edulis
Passionfruit
Sedum
pachyphyllum
Citrus limon
Meyer Meyer
Lemon
Banksia
spinulosa
Birthday
Candles
Anigozanthos
flavidus
Kangaroo Paw
Rosmarinus officinalis
R. officinalis prostratus
Rosemary (upright and
prostrate forms)
Wisteria sinensis Chinese

Wisteria
Sedum
xrubrotinctum
Olea
europaea
European
Olive
Hairpin
Banksia
cultivar
Dianella tasmanica
Tasmanian Flax-lily
Thymus vulgaris
Common Thyme
Aphanopetalum resinosum
Gum Vine
Sedum mexicanum
Mexican
Stonecrop
Themeda australis
Kangaroo Grass
Salvia officinalis
Culinary Sage
Pandorea jasminoides Alba
Aloe Always Red

Aloe Gemini
P. jasminoides Lady Di
Bower Vine cultivars
Kleinia repens
Chalk Sticks
Clematis glycinoides Forest

Clematis
Lampranthus
deltoides
Maintenance
The garden is maintained once a
month by a horticulturalist, and the
building management team carries out
some maintenance in between these
scheduled visits.
Plant nutrition is provided as eight to ninemonth low phosphorus controlled-release
fertiliser, applied at half the recommended
rate, as required.

The rooftop has been popular and is used
throughout the year as a social space by
the building occupants. The rooftop can be
booked for functions and is open annually
to the public as part of The Committee for
Melbournes Melbourne Open House.
Substrate installation
Costs
Component
Cost
Timber and metal work (including planter boxes, seats,

pergola, roof lift, access ladder, fencing and sculpture)
$135,850
Building preparation works (including scaffold, handrail, crane)
$14,500
General construction items (including roof access anchors,

signage, light, power and plumbing and upgrades for Building
Code of Australia compliance)
$35,608
Permeable paving
$23,220
Ronstan cables
$2,000
Plants
$5,000
Rainwater tank & pump
$2,500
Elmich green roof system
in-kind*
Growing media
in-kind
Plants
in-kindn
Further structural rod & cable systems for green walls and landscaping and cable systems for
balustrades and railings were provided at cost price by Ronstan Tensile Architecture, a sponsor of
Growing Up
*The green roof system and labour for installation was provided as in-kind support by sponsor
Green Roof Technologies, this had an estimated value of $60,000
Provided as in-kind support by sponsor WeBlow
n
Provided by sponsors Proteaflora, Aloe-Aloe Horticulture, Merrywood Plants and Majestic Plants,
this had an estimated value of $8,500
Appendix A
126
Appendix
Appendix
Green roof growing substrates

The design of a green roof growing substrate must include
specification of the following physical properties, outlined in Table
13. Many of these measures are used in the development of
growing media for containers and landscaping soils, making this
information relevant to development and testing of growing media
for use with some green wall and facade systems. Referenced
standards used to develop this table are AS 3743 2003, Appendix
B, and the Singapore Centre for Urban Greenery and Ecology
Standards: these are listed in the References section. It is valuable
to obtain independent testing and verification of the properties of
substrate mixes on large scale commercial green roof projects.
Table 13. Properties that should be specified in growing substrates
Definition
What it means in relation to green

roof substrates
Unit of
measurement
Saturated
bulk density
The mass of a known volume of

a material under fully saturated
conditions
The maximum possible weight of the growing

substrate (assuming no ponding water sitting
above the top of the substrate) as it includes
the weight of the material and of water that
drained freely from it under test conditions. This
parameter is set by the roof weight loading.
g/cm3 or kg/m3
Air filled
porosity
(AFP)
The percentage of air held by a

known volume of fully saturated
growing substrate, just after it has
stopped draining. AFP is measured
by watering and draining a known
volume of substrate under a set of
standard conditions described in
AS 3743 2003, Appendix B.
Property
Water
holding
capacity
(WHC)
pH
Electrical
conductivity
(EC)
The total amount of water

a known volume of growing
substrate can hold after it has
been watered and drained under
standard conditions described in
AS 3743 2003, Appendix B.
The measure of the acidity or

basicity (alkalinity) of a solution,
expressed as the negative log
concentration of free hydrogen ion
(H+) it contains.
Determination of the ability of salts

dissolved in solution to conduct
electricity
AFP provides an indication of the likely aeration

of the growing substrate and flags any potential
for waterlogging, in conjunction with water
holding capacity (below)
% (of known
substrate volume)
AFP should be 10 - 20%

WHC indicates how well the growing substrate
retains water.
WHC should be >35% or greater for an
extensive green roof, and 45% for an intensive
green roof (up to a maximum of 65%); WHC
will vary inversely with AFP (above) and an
acceptable balance of the two must be achieved
Determination of pH of an aqueous extract of a
growing substrate indicates whether any nutrient
deficiencies are likely, as pH affects the availability
of the nutrient supply to plants. Most plants show
optimal growth in growing media with pH of 6
to 7.
Optimum pH range may vary with substrate
composition pH 6 to 7.5 for mineral mixes; pH
5.5 6.5 for organic mixes; pH 5.5 8.0 should
provide acceptable growth for most species.
An indication of the degree of salinity of a
growing substrate: high salt content can impair
plant growth.
Growing substrates should have EC of less than
2 dS/m
% (of known
substrate volume)
No unit; range
from 1 (acid) to 14
(alkaline, or basic)
Solutions with
pH below 4 are
extremely acid,
and solutions with
pH above 10 are
extremely alkaline
deciSiemens per
metre (dS/m) or
measure total
dissolved salts in
ppm
127
Appendix
Appendix
Table 13. Properties that should be specified in growing substrates (continued)

Property
Definition
The ability of growing media to

attract and hold positively charged
ions (cations) thus making them
available for plants to take up
Cation
exchange
capacity
(CEC)
What it means in relation to green

roof substrates
Unit of
measurement
Cations such as calcium, magnesium, potassium

and ammonium (a source of nitrogen) are
crucial for healthy plant growth. Decomposition
of organic materials such as pine bark and coir
increase the cation exchange capacity of growing
substrates. Colloidal materials such as clay also
provide CEC but these are usually present in very
low proportions in green roof growing mixes.
milliequivalents or
ppm
Analytical laboratories determine CEC, by

measuring the amounts of different exchangeable
cations in growing media.
Growing substrates should have CEC of 50 100
mEq/l
For an extensive green roof growing substrate
the infiltration rate should be 1.0 mm/min or 60
l/m2/h
A measure of how rapidly water

soaks into a growing substrate,
growing medium or soil
Infiltration
rate
mm/min or l/m2/h
For an intensive green roof, infiltration rate s

should be 0.6 mm/min or 36 l/m2/h
Australian Standards also specify testing requirements for growing

substrates and media to ensure they are not toxic to plant growth.
Green roof growing substrates are designed to have a mix of large
and medium-sized particles to create an open, porous structure
inside which smaller particles can fit. The sizes and proportions
of small particles and their packing inside the large pores make a
major contribution to the amount of water the mix can retain.
Water is held by capillarity between small, tightly packed particles

in the growing substrate, and it is this water that is available to
plants. A mix with a high proportion of fine particles will retain
more water than a mix composed of few fine particles. Figure 24
compares the general characteristics of growing substrates used
on deeper and shallower green roofs.
Figure 24. A comparison of growing substrates

Particle
size
coarse
fine
low
high
Air-filled
porosity
high
low
Nutrient
reserves
low
high
Water-holding
capacity
The report The Matter of Landscape: Sustainable Design Strategies

for RMIT City Campus provides further information on different
elements growing mediums and their properties.
A growing substrate designed for a shallow green roof (left hand side)
will be more open and free draining than a substrate designed for a
deeper green roof (right hand side). Because of the shallow depth of
some roofs, the risk of waterlogging is great. Waterlogging decreases
oxygen in the root zone, and limits plant growth. Diagram adapted
from Zinco.
There are no Australian specifications for the composition and physical

properties of green roof growing substrate, and often international
specifications are used or adapted. Table 14 outlines the properties
of green roof growing substrates as specified by Germanys FLL and
Singapores Centre for Urban Greenery and Ecology.
128
Appendix
Appendix
Table 14. Properties of green roof growing substrates

Extensive
Intensive
Clay and silt content
<15% by mass
<20% by mass
Proportion of particles
> 4mm in diameter
< 50% by mass
< 40% by mass
Organic matter
< 65 g/l (FLL)

10-25% (CUGE)
< 90 g/l (FLL)

510% (CUGE)
Settling
No more than 10% of nominal depth
Average of < 5 cm for substrates at least

50 cm deep
Water permeability
0.6 - 70 mm/min
0.3 - 30 mm/min
Water storage capacity
> 35% by volume
> 45% by volume

(maximum of 65%)
Air-filled porosity
> 10%
> 10%
pH
6.0 8.5
6.0 8.5
Total soluble salts
1.5 - 3.5 g/l
1.5 - 2.5 g/l
Table 15 shows a range of components commonly used in green

roof growing substrates and reasons for using them, along with
indications of their saturated and dry weights. This represents a
very small number of components that could be used in growing
mixes. Comparative values for topsoil and sand are also provided
for reference, but their high bulk density often limits or precludes
their use.
Table 15. Comparison of materials used in green roof growing substrates and their saturated bulk density
Component
Reason used
Saturated bulk
density (kg/m)
Dry bulk density

(kg/m)
Ash
Waste product
1160 1310
640 900
Organic materials (coir,

pine bark, compost)
Waste product, water

retention, CEC
930 1100
50 360
Crushed ceramics
(brick, roof tile)
Longevity, recycled
1090 1300
1640 1720
Scoria aggregate rock
Longevity
1290 1560
670 1000
Scoria non-descript
crushed rock (NDCR)
Longevity
1530 1730
1030 1270
Perlite
Light weight
500 800
40
Pumice
(Hekla, Iceland)
Longevity; porous and

light weight
540 753
260 490
Hydrocell
Inert, water-retention
660
27
Loamy topsoil
1700 2400
1000 1900
Sand
1800 2200
1440 1650
Water
1000
Burnley extensive green roof medium
1370
Material
Recycled waste
products
Quarried products
Inert volcanic
products
Synthetic
additives
850
Values compiled from Handreck and Black, University of Melbourne Green Roof Infrastructure Group research data, Weiler and Scholz Barth, Dunnett
(Small Green Roofs) and JEI International.
129
Appendix
Appendix
Glossary
Basal shoots Shoots arising from buds at the stem bases or
roots of a plant. Continued production of basal shoots through
rejuvenation pruning is important to promote coverage of the
lower areas of a green facade, as some climbing plant species
open up at the base over time.
Personal protective equipment Safety clothing, helmets,

gloves, dust masks or independently ventilated masks, goggles and
safety glasses; abbreviated as PPE.
Controlled release fertiliser Fertiliser composed of

inorganic cations and anions held within resin beads or prills.
Nutrients are released over time as water solubilises the ions.
Controlled release fertiliser, abbreviated CRF, is also known as
slow release fertiliser.
pH The measure of acidity or alkalinity of a solution, pH ranges

from 1 (acid) to 14 (alkaline). Optimal growth of most plant
species is obtained with growing media that have pH values of 6
to 7.
Crop factor A measure of water use by plants, taking into

account their leaf area. The crop factor increases as plants
increase in size and require more water to support their growth,
and also varies with the season. Water use by leafy plants is higher
when temperatures are warm and solar radiation is high.
Cultivar Cultivated variety of a plant that has been selected for
some special attribute. Cultivated varieties are indicated with a
name included inside a pair of apostrophes e.g. Achillea Walther
Funcke.
Dead load Permanent weight load imposed on a structure
by the combination of fixed elements and by the weight of the
structure itself. Measured in kilograms per square metre.
Petiole The stalk of a leaf.
Porosity The ratio of the volume of void spaces in a substrate

(or soil) to the total volume. Porous substrates allow water and air
to move through.
Potable water Water that is safe for humans to drink
Rhizome An underground stem, arising from the root mass
of a plant, that gives rise to roots and shoots at nodes, and the
production of genetically identical plants.
Saturated bulk density The mass of a known volume of a
material under fully saturated conditions, expressed in g/cm3 or
kg/m3.
EC Electrical conductivity, a measure of the ability of salts

dissolved in solution to conduct electricity. High salt content in
the growing medium can impair plant growth.
Stolons Stems arising from buds the base of a plant, that grow
horizontally at or just below the soil surface. Roots and shoots
(leaves) will develop at nodes on a stolon, to produce a series of
interconnected, genetically identical plants e.g. runners produced
by strawberry plants.
Evapotranspiration The combined loss of water from

transpiration by plants and evaporation of water from the growing
substrate and plant surface.
Total dissolved solids A measure of all inorganic and

organic substances contained in a solution, measured in parts per
million
Fertigation Delivery of water for irrigation containing

dissolved low level fertiliser, used in hydroponic growing systems.
Transpiration Water movement through a plant, from its

uptake by the roots through water conducting tissues, to its exit
through openings in leaves and stems.
Growing medium/substrate Materials that act as a soil

substitute, providing physical support to the root system of a plant,
and delivering water, oxygen and nutrients needed for growth.
Growing media includes potting mixes used for containers,
through to specially designed growing substrates composed of
largely inorganic materials designed for use on green roofs.
Landscape coefficient A factor that is used to calculate
the rate of water loss by evapotranspiration, based on the crop
factor, the density of planting, and microclimatic factors that affect
water loss from the plants and growing medium (e.g. the degree
of shade on a site).
Live load Temporary weight load imposed on a structure by
the addition of people and moveable items.
Water-holding capacity The total amount of water a

known volume of growing substrate can hold after it has been
watered and drained under standard conditions described in
Australian Standard 3743 2003, Appendix B. Water-holding
capacity is expressed as a percentage (of substrate volume),
abbreviated as WHC.
WSUD Water Sensitive Urban Design is the planning of water
use on a site to build landscapes that work with the natural water
cycle. It includes treatments that are designed to avoid, or at least
minimise, the environmental impacts of urbanisation, such as rain
gardens or biofiltration ponds that are important in cleaning urban
run-off.

Green Guide Growing

Uploaded by

Copyright:

Available Formats

Green Guide Growing

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Green Guide Growing

Uploaded by

Copyright:

Available Formats

February 2014

Sidonie co-founded Green Roofs Australasia, the peak body

Figure 1. Pressure builds over our cities

Figure 2. Vegetation can be added to a building

Frequently asked questions

Benefits of green roofs, walls and facades

Reducing the energy budget of a building

Figure 5. A comparison of thermal effects on a green roof under different types of

Table 1. Effect of a green facade on building thermal performance

Contribution to urban cooling

Managing stormwater volume

Figure 11. Rainfall retention on green roofs with different slopes

Improving stormwater quality

Table 2. Comparison of nitrogen (N) and phosphorus (P) content in rainwater

Table 3. Comparison of nitrogen (N) and phosphorus (P) content in rainwater

Urban air quality

Human health and wellbeing

Green roof research at the University of Melbourne

2.1 Climatic factors on-site

Table 4. Weight loadings for some representative climbing species

Figure 13. Different types of roof drains

2.4 Existing structure and size

Table 6. Site analysis requirements

3. Design and Planning

3.1 Design objectives

Green roofs for biodiversity

3.2 Planning for drainage and irrigation

3.9 Designing for plant establishment

4. Building and Installation - General Advice

4.1 Occupational Health and Safety

Figure 17. Occupational Health and Safety legislative framework in Victoria

4.2 Insurance and system warranties

4.3 Project completion

5. Building and Installation - Green Roofs

Figure 18. Layers of a green roofs

5.1 Roof deck

Table 10. Common waterproofing treatments

5.3 Protection layers

5.4 Drainage layer

Figure 19. Tree anchoring systems

5.8 Thermal insulation

Table 11. Irrigation methods for green roofs

5.11 Wind considerations

Figure 20. Layers of a sloped roof

5.13 Hard landscape elements

Figure 21. Functional elements on a green roof

Stages of construction: Building the City of Monash green roof

6. Building and Installation - Green Walls

6.1 Structures and components for green wall systems

Figure 22. Types of green wall configurations

7. Building and Installation - Green Facades

7.1 Wall protection and different facade treatments

7.2 Soils and growing substrates

8.1 Maintenance planning

Table 12. Common maintenance tasks

8.3 Plant nutrition

Victorian Case Studies

The Venny Green Roof

The Triptych Green Wall

RMIT University Building 21 Green Facade