RouterBOARD

951-2n
Quick Setup Guide and Warranty Information
Connecting
1. Connect your WAN cable to port 1, and LAN PCs to ports 2-5
2. Set LAN computer IP configuration to automatic (DHCP)
3. Default IP address from LAN/WLAN is 192.168.88.1, open this
address in your web browser to start configuration. The username is
admin and there is no password (Alternatives are SSH, Telnet or
Winbox tool)
4. Wireless AP mode is enabled by default, you can connect to the SSID
MikroTik. Log into your router and configure a WPA password to
secure your network

Powering
The device accepts powering from the power jack or from the first ethernet port (Passive PoE):

DC power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts 8-30V DC
The first ethernet port accepts passive Power over Ethernet accepts 8-30V DC

Under maximum load, the power consumption of this device is 3W

Booting process
Initial connection has to be done via the Ethernet cable. Open 192.168.88.1 in your web browser, and choose
Webfig for browser based configuration or Winbox for a Windows utility with the same functions. Username
is admin and there is no password. In case IP connection is not available, Winbox can be used to connect to the
MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button
of the device when starting it until the LED light turns off, and Metal will start to look for Netinstall servers.

Extension Slots and Ports

Five individual 10/100 Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X),
so you can use either straight or cross-over cables for connecting to other network devices. The First
Ethernet port accepts 8-30V DC powering from a passive PoE injector.
One Integrated Wireless 2.4GHz 802.11b/g/n, 1x1 MIMO with two onboard PIF antennas, max gain 1.5dBi

See www.routerboard.com for more information. Contact support@mikrotik.com

21-Aug-13

Buttons and Jumpers

RouterOS reset jumper hole (on the bottom of case, behind one of the rubber feet) resets RouterOS
software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example)
and boot the device. Hold screwdriver in place until RouterOS configuration is cleared.
RouterBOOT reset button (RESET, front panel) has two functions:
o Hold this button during boot time until LED light starts flashing,
release the button to reset RouterOS configuration (same result as with RouterOS reset hole)
o Hold this button during boot time longer, until LED turns off,
then release it to make the RouterBOARD look for Netinstall servers.

Operating System Support

Currently tested operating system is MikroTik RouterOS starting from version v5.15

Copyright and Trademarks.

Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be
reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,
RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks
appearing in this manual are the property of their respective holders.
Hardware. MikroTik warrants all RouterBOARD series equipment for the term one year from the shipping date to
be free of defects in materials and workmanship under normal use and service, except in case of damage caused
by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain,
fire or other acts of nature.
To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)
procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA
process.
1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company
regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your
equipment directly from MikroTik in Latvia.
2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for
RB1000 series.
3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the
sender at sender's cost.
RMA Instructions are located on our webpage here: http://rma.mikrotik.com
Manual. This manual is provided as is without a warranty of any kind, expressed or implied, including, but not
limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has
made every effort to ensure the accuracy of the contents of this manual, however, it is possible that it may
contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in
this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such
an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to
support@mikrotik.com

See www.routerboard.com for more information. Contact support@mikrotik.com

21-Aug-13

Federal Communication Commission Interference Statement (FCC ID:

TV7RB951-2N )
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the users authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other antenna or
transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to
general public. Under such configuration, the FCC radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas
in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use
of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules
CFR47 part 15.204. The installer should configure the output power level of antennas, according to country
regulations and per antenna type. Professional installation is required of equipment with connectors to ensure
compliance with health and safety issues.

See www.routerboard.com for more information. Contact support@mikrotik.com

21-Aug-13

CE Declaration of Conformity
Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/
[EN] English
[BG] Bulgarian
[CZ] Czech
[DK] Danish
[DE] German
[EE] Estonian
[GR] Greek
[ES] Spanish
[IT] Italian
[LV] Latvian
[LT] Lithuanian
[HU] Hungarian
[NL] Dutch
[PL] Polish
[PT] Portuguese
[RO] Romanian
[SK] Slovak
[SI] Slovenian
[FI] Finish
[SE] Swedish
[NO] Norwegian

Hereby, MIKROTKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
, MIKROTKLS SIA , ROUTERBOARD -
1999/5/EC.
MIKROTKLS SIA tmto prohlauje, e ROUTERBOARD spluje zkladn poadavky a vechna pslun ustanoveni Smrnice 1999/5/ES.
Undertegnede MIKROTKLS SIA erklrer herved, at flgende udstyr ROUTERBOARD overholder de vsentlige krav og vrige relevante krav i
direktiv 1999/5/EF.
Hiermit erklrt MIKROTKLS SIA dass sich das Gert ROUTERBOARD in bereinstimmung mit den grundlegenden Anforderungen und den
brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Kesolevaga kinnitab MIKROTKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele stetele.
MIKROTKLS SIA ROUTERBOARD
1999/5/
Por la presente, MIKROTKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la
Directiva 1999/5/EC.
Con la presente MIKROTKLS SIA dichiara che questo ROUTERBOARD conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Ar o MIKROTKLS SIA deklar, ka ROUTERBOARD atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem.
iuo MIKROTKLS SIA deklaruoja, kad is ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas
A MIKROTKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD tpus beren-dezs teljesti az alapvet kvetelmnyeket s ms 1999/5/EK
irnyelvben meghatrozott vonatkoz rendelkezseket.
Hierbij verklaart MIKROTKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentile eisen en de andere relevante
bepalin-gen van richtlijn 1999/5/EG.
Niniejszym MIKROTKLS SIA deklaruje e ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi waciwymi postanowieniami
Dyrektywy 1999/5/EC.
Eu, MIKROTKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provises relevantes da Directiva 1999/5/EC.
Prin prezenta, MIKROTKLS SIA declar c aparatul ROUTERBOARD este n conformitate cu cerinele eseniale i cu alte prevederi pertinente
ale Directivei 1999/5/CE..
MIKROTKLS SIA tmto vyhlasuje, e ROUTERBOARD spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES.
MIKROTKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi doloili direktive 1999/5/ES.
MIKROTKLS SIA vakuuttaa tten ett ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien
direktiivin muiden ehtojen mukainen.
Hrmed intygar MIKROTKLS SIA att denna RouterBOARD r i verensstmmelse med de vsentliga egenskapskrav och vriga relevanta be-
stmmelser som framgr av direktiv 1999/5/EG.
MIKROTKLS SIA Erklrer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF.

BG. : , . 192.168.88.1 , .
http://wiki.mikrotik.com CZ. Nvod k pouit: Pipojte napjec adaptr k zapnut pstroje. Otevete 192.168.88.1 ve webovm pro-
hlei pro konfiguraci produktu. Vce informac najdete v http://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strmadapteren for at tnde for enheden.
bn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur
d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans
http://wiki.mikrotik.com DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gert einzuschalten. ffnen Sie 192.168.88.1 in einem Web-Browser,
um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend: hendage toiteadapter seadme sissellitamiseks.
Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte el adaptador de
alimentacin para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Ms informacin en http://wiki.mikrotik.com
IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unit. Aprire 192.168.88.1 in un browser Web per configurare il prodotto.
Maggiori informazioni in http://wiki.mikrotik.com LV. Lietoanas instrukcija: Pievienojiet Strvas adapteri, lai ieslgtu ierci. Atvrt 192.168.88.1 ar interneta
prlku, lai konfigurtu produktu. Plaka informcija http://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapter junkite rengin.
interneto narykl 192.168.88.1 Atidarykite galite konfigruoti gamin. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Hasznlati utasts:
Csatlakoztassa a hlzati adaptert a kszlk bekapcsolshoz. Megnyitsa 192.168.88.1 egy webbngszben belltani a termket. Tbb informci
http://wiki.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product
te configureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsugi: Podcz adapter zasilania, aby wczy urzdzenie. Otwrz 192.168.88.1
w przegldarce internetowej, aby skonfigurowa urzdzenie. Wicej informacji w http://wiki.mikrotik.com PT. Manual de instrues: Conecte o adaptador
de alimentao para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informaes em
http://wiki.mikrotik.com RO. Instruciuni de utilizare : Conectai adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 ntr-un browser
web pentru a configura produsul. Mai multe informaii n http://wiki.mikrotik.com SK. Nvod na pouitie: Pripojte napjac adaptr k zapnutiu prstroja.
Otvorte 192.168.88.1 vo webovom prehliadai pre konfigurciu produktu. Viac informci njdete v http://wiki.mikrotik.com SI. Navodila: Prikljuite
napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Ve informacij v http://wiki.mikrotik.com FI. Kyttohje: Kytke
virtalhde plle laitteen. Avaa 192.168.88.1 in selaimen mritt tuotteen. Lis tietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut ntadap-
tern fr att sl p enheten. ppna 192.168.88.1 i en webblsare fr att konfigurera produkten. Mer information p http://wiki.mikrotik.com NO.
Bruksanvisningen: Koble strmadapteren for sl p enheten. pne 192.168.88.1 i en nettleser for konfigurere produktet. Mer informasjon p
http://wiki.mikrotik.com GR. : . 192.168.88.1
Web . http://wiki.mikrotik.com

See www.routerboard.com for more information. Contact support@mikrotik.com

21-Aug-13