Claa170ea07p y PDF
Claa170ea07p y PDF
Technical Specification
To :
Date : 2007/04/19
CPT TFT-LCD
CLAA 170EA07P
ACCEPTED BY
APPROVED BY
Joe Chou
CHECKED BY
PREPARED BY
Tristan Wang
TFT-LCD Product
Planning
Management General
Division
Doc. No:
CLAA170EA07PY-Ver1-20070214
Issue Date:
2007/04/19
CPT
1.OVERVIEW
CLAA170EA07P is 17.0 color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
composed of LCD panel, driver ICs, control circuit and backlight. By applying 8 bit digital data,
12801024, 16.7M-color images are displayed on the 17.0 diagonal screen. Input power voltage is 5.0V
for LCD driving.Inverter for backlight is not included in this module. General specification are
summarized in the following table:
ITEM
Display Area(mm)
Number of Pixels
Pixel Pitch(mm)
Color Pixel Arrangement
Display Mode
Number of Colors
Brightness(cd/m^2)
Viewing Angle
Surface Treatment
Power consumption(W)
Module Size(mm)
Module Weight(g)
Backlight Unit
CPT Confidential
SPECIFICATION
337.920(H)x270.336(V)
(17.0-inch diagonal)
1280(H)x1024(V)
0.264(H)x0.264(V)
RGB vertical stripe
normally white, TN
16.7M (6 Bit+Hi-FRC)
300 cd/m2(Typ.)(Center point, Lamp current=7.5 mA)
160 / 160(Typ.)
Anti-glare
23.7 (Typ.)
358.5(W)x296.5(H)x17.5(D)(max)
2200(typ)
CCFL, 4 tables, edge-light(top*2/bottom*2)
2/25
CPT
MIN.
0
MAX.
6
UNIT
V
Lamp Voltage
VL
590
832
Vrms
Lamp Current
ILO
mArms
Lamp Frequency
FL
VESDt
VESDc
Top
Tstg
TD
40
-200
-8000
0
-20
--
80
200
8000
50
60
1
kHz
V
V
sec
static electricity
Operation Temperature
Storage Temperature
Delayed Discharge Time
REMARK
*4). 7)
*5)
*1). 2). 3). 6)
*1). 2). 3)
*8)
[Note]
1).The relative temperature and humidity range are as below sketch, 90%RHMax.(Ta40).
2).The maximum wet bulb temperature 39(Ta40) and without dewing.
3).If you use the product in a environment which over the definition of temperature and humidity too
long to effect the result of eye-atching.
4).The life time of the lamp is relate to the current of the lamp, so please accronding to the
description of the (b) backlight on page 7.
5).Test Condition: IEC 1000-4-2
VESDt: Contact discharge to input connector; VESDC: Contact discharge to module
6).If you operate the product in normal temperature range, the center surface of panel should be under
60.
7).When lamp current is out of the absolute maximum range, the life will fall rapidly or shown
unusual sign.
IL min 2mA only for test only, but we cant guarantee the lifetime and performance.
8).Delay lighting testing needs the volt above start volagte Vrms.Before the procedure tube needs
typical lighting for 1 minute and stay in the temperature 252 for 24 hours and then testing in the
same condition in dark room .
CPT Confidential
3/25
CPT
CPT Confidential
4/25
CPT
3. ELECTRICAL CHARACTERISTICS
(1).TFT-LCD
Ta=25
ITEM
SYMBOL MIN
Power Supply Voltage for LCD
Vcc
4.5
Power Supply Current for LCD
Icc
Permissive Input Ripple Voltage
VRP
Differential impedance
Zm
90
Common
VCM
1.125
Mode Voltag
Differential
|VID|
250
Logic input voltage Input Voltage
LVDS:IN+IN- Threshold
VTH
Voltage(High)
Threshold
VTL
-100
Voltage(Low)
LCD Inrush Current
Inrush
Power consumption
P
[Note]
1).VCC-turn-on conditions:
0.5mst110ms
1 sect4
0t220ms
200mst5
0t350ms
200mst6
TYP
5.0
700
100
MAX
5.5
950
100
110
UNIT Remark
V
*1)
mA
*2)
mVp-p Vcc=5.0V
1.25
1.375
350
450
mV
100
mV
*3)
mV
3.5
3
4.75
A
W
Vin=5.0V
4.5V
4.5V
data
0.5V
0.5V
t1
t2
t3
VL
t5
t6
VCC-dip conditions:
(1) When 3.6VVcc(min)<4.5V: td10 ms
CPT Confidential
5/25
t4
0.5V
*4)
*2)
CPT
2).Typical current situation: 64 gray scale level,1280 line mode, VCC=5.0V, Fh=64Khz,Fv=60Hz,
Fclk=54 MHz.
3).LVDS Signal definition:
CPT Confidential
6/25
CPT
(2).Backlight
1.Electrical specification
ITEM
MAX
UNIT
REMARK
728.2
Vrms
IL=7.5mA
Ta=25
B/L Voltage
VL
B/L Current
B/L operating current
IL
ILO
7
3
7.5
7.5
8
8
mArms
mArms
WL
20.2
22.2
Inverter Frequency
FI
VS
45
50
65
1600
1450
kHz
Vrms
Vrms
*1) Ta=25
*1) Ta=25
IL=7.5mA
Ta=25
*2) Ta=25
Ta=0
Ta=25
ILO at 2.0 mA ILO at 3.0 mA ILO at 7.0 mA ILO at 7.5 mA ILO at 8.0 mA UNIT REMARK
Min. 40,000
Min. 40,000
Min. 30,000
hr
Continuous
Operation
*3)
Rated time
(turn on/off)
Min.100,000
time
*4)
CPT Confidential
7/25
CPT
DIVLCP0506D42
If the waveform of light up-driving is asymmetric, the distribution of mercury inside the lamp
tube will become unequally or will deplete the Ar gas in it. Then it may cause the abnormal
phenomenon of lighting-up. Therefore, designers have to try their best to forfill the conditions
under the inverter designing-stage as below:
The degrees of unbalance 10%
The ratio of wave height2 10%
1) Lamp Current measurement method ( The current meter is inserted in cold line)
CTL
CTH
CTL
CTH
INVERTER
LCD
Module
CTL
CTH
CTL
PowerSupply
CTH
2) a.Frequency in this range can mala the characterisitics of electric and optics maintain in +/- 10%
except hue.
b.If the lamp frequency can be maintain in 50~60KHz, the better charactristics of the electrical
and the optical can be presented.
c.If the operating frequency is 40~80 KHz, the life time and the reliability of the lamp will not be
affect.
d.Lamp frequency of inverter may produce interference with horizontal synchronous
frequency,and this may cause horizontal beat on the display.Therefore, please adjust lamp
CPT Confidential
8/25
CPT
CPT Confidential
9/25
CPT
CPT Confidential
CTL
10/25
CPT
5. INTERFACE TIMING
(1) Timing Specifications
ITEM
SYMBOL MIN
TYP
MAX
Frequency
fCLK
45
54
70
DCLK
14.3
18.5
22.2
Period
tCLK
Horizontal Active Time
tHA
640
640
640
Horizontal Blank Time
tHB
45
204
390
LCD
Timing
Horizontal Total Time
tH
685
844
1030
tVA
1024
1024
1024
DENA Vertical Active Time
Vertical Blank Time
tVB
12
42
376
Vertical Total Time
tV
1036
1066
1400
Vertical Frame Rate
50
Fr
60
75
[Note]
1) DENA should always be positive polarity as shown in the timing specification.
2) CLK INshould appear during all blanking period,
3) Using LVDS IC
Receiver
Transmitter
DS90C384MTD(NS)
DS90C383MTD(NS)
SN75LVDS82(TI)
SN75LVDS83(TI)
UNIT
MHz
ns
tCLK
tCLK
tCLK
tH
tH
tH
Hz
CPT Confidential
Require Signal
Pin No.
Power Supply for TTL Input
29
TTL Input (R7)
30
TTL Input (R5)
31
TTL Input (G0)
32
Ground pin for TTL
33
TTL Input (G1)
34
TTL Input (G2)
35
TTL Input (G6)
36
Power Supply for TTL Input
37
TTL Input (G7)
38
TTL Input (G3)
39
TTL Input (G4)
40
Ground pin for TTL
41
TTL Input (G5)
42
TTL Input (B0)
43
TTL Input (B6)
44
Power Supply for TTL Input
45
TTL Input (B7)
46
TTL Input (B1)
47
TTL Input (B2)
48
Ground pin for TTL
49
TTL Input (B3)
50
TTL Input (B4)
51
TTL Input (B5)
52
11/25
Pin Name
GND
D26
TxCLKIN
PWR DWN
PLL GND
PLL VCC
PLL GND
LVDS GND
TxOUT3+
TxOUT3TxCLKOUT+
TxCLKOUTTxOUT2+
TxOUT2LVDS GND
LVDS VCC
TxOUT1+
TxOUT1TxOUT0+
TxOUT0LVDS GND
D27
D0
D1
Require Signal
Ground pin for TTL
TTL Input(DE)
TTL Level clock Input
Power Down Input
Ground pin for PLL
Power Supply for PLL
Ground pin for PLL
Ground pin for LVDS
Positive LVDS differential data output 3
Negative LVDS differential data output 3
Positive LVDS differential clock output
Negative LVDS differential clock output
Positive LDVS differential data output 2
Negative LVDS differential data output 2
Ground pin for LVDS
Power Supply for LVDS
Positive LVDS differential data output 1
Negative LVDS differential data output 1
Positive LVDS differential data output 0
Negative LVDS differential data output 0
Ground pin for TTL
TTL Input (R6)
TTL Input (R0)
TTL Input (R1)
CPT
D23
VCC
D24
D25
b.Vertical Timing
CPT Confidential
12/25
53
54
55
56
GND
D2
D3
D4
CPT
*)DS90C383MTD
CPT Confidential
13/25
CPT
R DATA
R6 R5 R4 R3 R2 R1 R0
LSB
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 1
0 0 0 0 0 1 0
G7
MSB
0
0
1
0
1
0
1
1
0
0
0
G DATA
G6 G5 G4 G3 G2 G1 G0
LSB
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
B7
MSB
0
0
0
1
1
1
0
1
0
0
0
B DATA
B6 B5 B4 B3 B2 B1 B0
LSB
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
RED(254)
RED(255)
GREEN(0)
GREEN(1)
GREEN(2)
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
GREEN(254)
GREEN(255)
BLUE(0)
BLUE(1)
BLUE(2)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
BLUE(254)
BLUE(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
GREEN
BLUE
[Note]
1) Definition of gray scale: Color(n) : n indicates gray scale level.
Higher n means brighter level.
2) Data:1-High,0-Low.
3) This assignment is applied to both odd and even data.
CPT Confidential
14/25
CPT
D(2,1)
--
D(X,1)
--
D(1279,1)
D(1280,1)
D(1,2)
D(2,2)
--
D(X,2)
--
D(1279,2)
D(1280,2)
..
D(1,Y)
D(2,Y)
--
D(X,Y)
--
D(1279,Y) D(1280,Y)
..
--
D(X, 1023)
--
--
D(X, 1024)
--
|
|
D(1279,102 D(1280,102
3)
3)
D(1279,102 D(1280,102
4)
4)
CPT Confidential
15/25
CPT
6. BLOCK DIAGRAM
TFT-LCD Module
CN2
CN3
Source Driver
Gate Driver
Power Supply
Circuit
LCD Panel
1280 X 3 X 1024
CN4
CN5
CN2,4
1
2
CCFL
1
2
CN3,5
CPT Confidential
16/25
CPT
7. MECHANICAL SPECIFICATION
(1) Front side (Tolerance is 0.5mm unless noted)
Unit: mm
17/25
CPT
CPT Confidential
18/25
CPT
8. OPTICAL CHARACTERISTICS
Ta=25VCC=5.0V
ITEM
SYMBOL CONDITION
Contrast Ratio
Luminance(CEN)
9P Uniformity
Response Time
Crosstalk
Viewing Horizontal
Angle
Vertical
CR
L
L
Tr +Tf
CT
= 0
= 0
= 0
= 0
= 0
min
typ
max
UNIT
REMARK
550
250
75
-0
800
300
-5
--
---12
1
*1)
*2)
*2)
*4)
*5)
140
160
--
140
160
--
-cd/m2
%
ms
%
CR10
White
X
Y
0.283
0.299
0.313
0.329
0.343
0.359
Red
X
Y
(0.625)
(0.297)
(0.655)
(0.327)
(0.685)
(0.357)
(0.243)
(0.587)
(0.273)
(0.617)
(0.647)
(0.114)
(0.060)
(0.144)
(0.090)
(0.174)
(0.120)
(70)
2.0
(72)
2.2
-2.4
Color
Coordinates
Green
X
Y
Blue
X
Y
Gamut
Gamma
CG
= 0
= 0
VESA
Color
Coordinates
(0.303)
%
--
*3)
*2)
*6)
[Note]
All optical specification condition:
(1) Equipment: BM-5A(TOPCON) under the dark room condition( 2 view angle) after more than
30 minutes turning on the lamp.
(2) Condition: IL=7.5 (each lamp)mA, Inverter: SAMPO ( DIVLCP0506D42 ), Frequency=50kHz.
1).Defination of Contrast Ratio:
CR=ON (White) Luminance/OFF (Black) Luminance
2).Definition of Luminance and Luminance uniformity:
Center Luminance: measuring the luminance of the point no. 5
Average Luminance: measuring average luminance of points no.1-no.9
Uniformity: L=[L(Min)/L(Max)]100 %
CPT Confidential
19/25
CPT
Upper
Right
Left
Lower
White
90 %
90 %
Luminan
10 %
tr
Black
5) Definition of crosstalk:
CPT Confidential
10 %
20/25
tf
CPT
Pattern A
Pattern B
y =x-k
T
%
L
O
LOG
Gray level(LOG)
CPT Confidential
21/25
CONDITIONS
50; 90%RH; 240h
(No condensation)
60; 90%RH;48h
(No condensation)
50; 240h
60; 240h
0; 240h
-20; 240h
BETWEEN -20(1hr)AND 60(1hr); 100
CYCLES
CPT
CONDITIONS
Shock level:1470m/s^2(150G)
SHOCK
Waveform: half sinusoidal wave, 2ms
(NON-OPERATIO
Number of shocks: one shock input in each direction of three
N)
mutually perpendicular axes for a total of six shock inputs
Vibration level: 9.8m/s^2(1.0G) zero to peak
Waveform: sinusoidal
VIBRATION
Frequency range: 5 to 500 Hz
(NON-OPERATIO
Frequency sweep rate: 0.5 octave/min
N)
Duration: one sweep from 5 to 500Hz in each of three mutually
perpendicular axis(each x,y,z axis: 1 hour, total 3 hours)
(3) ESD
POSITION
Connector
Moudle
CONDITION
260HPa (30000 ft.)24 Hr
CPT Confidential
22/25
CPT
23/25
CPT
(3) PRECAUTFONSWITHELECTROSTATICS
1) This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be
affected by electrostatics. Please be careful with electrostatics by the way of your body
connecting to the ground and so on.
2) Please remove protection film very slowly on the surface of LCD module to prevent from
electrostatics occurrence.
(4) STORAGE PRECAUTIONS
1) When you store LCDs for a long time, it is recommended to keep the temperature between
0 ~40 without the exposure of sunlight and to keep the humidity less than 90%RH.
2) Please do not leave the LCDs in the environment of high humidity and high temperature such as
60 90%RH.
3) Please do not leave the LCDs in the environment of low temperature; below -20.
(5) SAFETY PRECAUTIONS
1) When you waste LCDS, it is recommended to crush damaged or unnecessary LCDs into pieces
and wash them off with solvents such as acetone and ethanol, which should later be burned.
2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off
thoroughly with soap and water.
(6) OTHERS
1) A strong incident light into LCD panel might cause display characteristics' changing inferior
because of polarizer film, color filter, and other materials becoming inferior. Please do not
expose LCD module direct sunlight Land strong UV rays.
2) Please pay attention to a panel side of LCD module not to contact with other materials in
preserving it alone.
3) For the. packaging box, please pay attention to the followings:
CPT Confidential
24/25
CPT
CPT Confidential
25/25