Professional Documents
Culture Documents
AS15G
AS15G
FEATURES Wide supply voltage range 6.5V ~ 18V Rail-to-rail output swing (The highest two
stage & lowest two stage)
GENERAL DESCRIPTION
The EC5575 is a 14+1 channel voltage buffers that buffers reference voltage for gamma correction in a thin film transistor liquid crystal display (TFT LCD). This device incorporating a Vcom amplifier circuits, four rail to rail buffer amplifier circuits (the highest two stage and lowest two stage) and 10 buffer amplifiers circuits. The EC5575 is available in a space saving 48-pin TQFP package, and the operating temperature is from 20C to +85C.
High slew rate 1V/s GBWP 1 MHz 2 MHz -3dB Bandwidth Large Vcom Drive Current: 100mA(Max) Ultra-small Package TQFP-48 APPLICATIONS TFT-LCD Reference Driver PIN ASSIGNMENT ( E Type )
Li 36 Mi Ni 37 Li 38 Mi Vcomi 39 Ni N.C 40 Comi N.C 41 N.C 42 VDD 43 Vss 44 VDD 45 Jo Vss 46 Ko Vcomo 47 Como Ii Ki 35 Ji 34 Ii 33 Hi 32 Vss 31
VDD 30
Gi 29
Fi 28
Ei 27
Di 26
Ci 25 24 Bi
Fi Gi Hi Bi Fo Mo No Ki Ho Ei Io Co Bo Ji Go Di Ao Ci
23
Ai
22 VDD Ai 21 Vss 20 Ao
Lo
19 Vss 18 Bo
Eo No 48 1 Mo 2 Lo 3 Ko 4 Jo 5 Io 6 Ho 7 Vss 8 VDD 9 Go 10 Fo 11 Eo 12 Do 13 Co
Ordering Information
Part No. Top Mark Package Description EC5575-F AS15-F TQFP48 14+1 lead-free EC5575-G AS15-G TQFP48 14+1 Green Package EC5575-FR AS15-F TQFP48 14+1 lead-free; (R) : Tape & reel EC5575-GR AS15-G TQFP48 14+1 Green Package; (R) : Tape & reel EC5575-HF AS15-HF TQFP48 14+1 lead-free ( H ) EC5575-HG AS15-HG TQFP48 14+1 Green Package ( H ) EC5575E2-F AS15E2-F TQFP48 14+1 (pin40 is Vcom-) lead-free EC5575E2-G AS15E2-G TQFP48 14 channel (pin40 is Vcom-)Green Package EC5575E2-HF AS15E2-HF TQFP48 14+1 (pin40 is Vcom-) lead-free ( H ) EC5575E2-HG AS15E2-HG TQFP48 14 channel (pin40 is Vcom-)Green Package (H) Note: (H): Exposed pad (3.05x3.05 mm) ; (R) : Tape & reel
Page 2 of 12
2007/09/12
Values beyond absolute maximum ratings may cause permanent damage to the device. These are stress ratings only; functional device operation is not implied. Exposure to AMR conditions for extended periods may affect device reliability.
Supply Voltage between VS+ and VS+18V Input Voltage (For rail-to-rail ) VS-0.5V, VS +0.5V Maximum Continuous Output Current (A ~ N uffers) 30mA Maximum Continuous Output Current(Com Buffer) 100mA Maximum Die Temperature +150C Storage Temperature Operating Temperature Lead Temperature ESD Voltage -65C to +150C -20C to +85C 260C 2kV
Important Note:
All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
ELECTRICAL CHARACTERISTICS
VS+= +5V, VS - = -5V, RL = 10k and CL = 10pF to 0V, TA = 25C unless otherwise specified.
Parameter Description Input Characteristics VOS Input Offset Voltage TCVOS IB RIN CIN VOL VOH VOL VOH ISC IOUT Average Offset Voltage Drift Input Bias Current Input Impedance Input Capacitance
Min
Typ 2 5 2 1 1.35
Max 12 50
Units mV V/C nA G pF
Output Characteristics Output Swing Low Output Swing High Output Swing Low Output Swing High Short Circuit Current Output Current ISC(Com) Short Circuit Current IOUT(Com) Output Current Power Supply Performance
PSRR IS IS(Com) Power Supply Rejection Ratio
IL= -5mA (A, B, M, N rail-to-rail Buffers) IL= 5mA (A, B, M, N rail-to-rail Buffers) 4.85 IL= -5mA (C ~ L Buffers) -3.5 IL= 5mA (C ~ L Buffers) 3.5
(A ~ N Buffers) (A ~ N Buffers) (Com Buffer) (Com Buffer)
-4.92 4.92
-4.85
V V V V mA mA mA mA
dB A mA
Supply Current (Per Amplifier) No Load (A ~ N Buffers) Supply Current (Com Buffer)
Dynamic Performance -4.0VVOUT4.0V, 20% to 80% SR Slew Rate [2] tS Settling to +0.1% (AV = +1) (AV = +1), VO=2V Step RL = 10K, CL = 10PF BW -3dB Bandwidth RL = 10K, CL = 10PF PM Phase Margin CS Channel Separation f = 1 MHz 1. Measured over operating temperature range 2. Slew rate is measured on rising and falling edges
1 5 2 60 75
V/s s MHz
Degrees
dB
Page 3 of 12
2007/09/12
Input Offset(mV)
Page 4 of 12
2007/09/12
Page 5 of 12
2007/09/12
Figure 2. Operation with Beyond-the Rails Input Power Dissipation The EC5575 is designed for maximum output current capability. Even though momentary output shorted to ground causes little damage to the device. For the high drive amplifier EC5575, it is possible to exceed the 'absolute-maximum junction temperature' under certain load current conditions. Therefore, it is important to calculate the maximum junction temperature for the application to determine if load conditions need to be modified for the amplifier to remain in the safe operating area. The maximum power dissipation allowed in a package is determined according to:
PDmax =
Figure 1. Operation with Rail-to-Rail Input and Output
TJmax - TAmax JA
Output Short Circuit Current Limit A +/-120mA short circuit current will be limited by the EC5575 if the output is directly shorted to the positive or the negative supply. For an indefinitely output short circuit, the power dissipation could easily increase such that the device may be damaged. The internal E-CMOS Corp. (www.ecmos.com.tw)
Where: TJmax = Maximum Junction Temperature TAmax= Maximum Ambient Temperature JA = Thermal Resistance of the Package
2007/09/12
Page 6 of 12
The maximum power dissipation actually produced by an IC is the total quiescent supply current times the total power supply voltage, plus the power in the IC due to the loads, or: PDmax =i[VS * ISmax + (VS+ VO) * IL] When sourcing, and PDmax = i[VS * ISmax + (VO VS-) * IL] When sinking. Where: i = 1 to 4 VS = Total Supply Voltage ISmax = Maximum Supply Current Per Amplifier VO = Maximum Output Voltage of the Application IL= Load current RL= Load Resistance = (VS+ VO)/IL = (VO VS-)/ IL A calculation for RL to prevent device from overheat can be easily solved by setting the two PDmax equations equal to each other.
Pin Count
TQFP-48 TQFP-48
ja (oC/W)
67 31
jc (C/W)
31 15 Normal EXPOSED PAD
1V Driving Capacitive Loads The EC5575 is designed to drive a wide range of capacitive loads. In addition, the output current handling capability of the device allows for good slewing characteristics even with large capacitive loads. The combination of these features make the EC5575 ideally for applications such as TFT LCD panel grayscale reference voltage buffers, ADC input amplifiers, etc. As load capacitance increases, however, the -3dB bandwidth of the device will decrease and the peaking increase. The amplifiers drive 10pF loads in parallel with10K. with just 1.5dB of peaking, and 100pF with 6.4dB of peaking. If less peaking is desired in these applications, a small series resistor (usually between 5 and 50 ) can be placed in series with the output. However, this will obviously reduce the gain slightly. Another method of reducing peaking is to add a "snubber" circuit at the output. A snubber is a shunt load consisting of a resistor in series with a capacitor. Values of 150 and 10nF are typical. The advantage of a snubber is that it improves the settling and overshooting performance
Page 7 of 12
2007/09/12
Page 8 of 12
2007/09/12
25 37
13
25 37
Page 9 of 12
2007/09/12
37
24
7.0 0.10
9.0 0.20
48
13
0.21 0.04
12
0.50
1.0 0.06
1.2 max.
0.15 0.05
0.6 0.15
3.5 o 3 o
1.00 BSC.
Page 10 of 12
2007/09/12
Page 11 of 12
2007/09/12
E-CMOS CORPORATION IC DATASHEET ADDRESS: NO.1, CREATION RD. 2ND, SCIENCE-BASED INDUSTRIAL PARK, HSIN-CHU 300, TAIWAN, R.O.C. WEBSITE: http://www.ecmos.com.tw E-MAIL: mailto:sales@ecmos.com.tw TEL: 886-3-5785888 FAX: 886-3-5783630
Page 12 of 12
2007/09/12