CA3160
CA3160
Features
MOSFET Input Stage Provides: - Very High ZI = 1.5T (1.5 x 1012) (Typ) - Very Low II . . . . . . . . . . . . . 5pA (Typ) at 15V Operation . . . . . . . . . . . . . . . . . . . . . . . 2pA (Typ) at 5V Operation Common-Mode Input Voltage Range Includes Negative Supply Rail; Input Terminals Can Be Swung 0.5V Below Negative Supply Rail CMOS Output Stage Permits Signal Swing to Either (or Both) Supply Rails
Applications
Ground Referenced Single Supply Amplifiers Fast Sample Hold Amplifiers Long Duration Timers/Monostables High Input Impedance Wideband Amplifiers Voltage Followers (e.g., Follower for Single Supply D/A Converter) Wien-Bridge Oscillators Voltage Controlled Oscillators Photo Diode Sensor Amplifiers
Pinout
CA3160 (PDIP) TOP VIEW
OFFSET NULL INV. INPUT NON-INV. INPUT V-
Ordering Information
PART NUMBER CA3160AE CA3160E TEMP. RANGE (oC) -55 to 125 -55 to 125 PACKAGE 8 Ld PDIP 8 Ld PDIP PKG. NO. E8.3 E8.3
1 2 3 4
7 6 5
NOTE: CA3160 Series devices have an on-chip frequency compensation network. Supplementary phase compensation or frequency roll-off (if desired) can be connected externally between Terminals 1 and 8.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002. All Rights Reserved
CA3160, CA3160A
Absolute Maximum Ratings Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . .+16V Differential Mode Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . .8V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . (V+ +8V) to (V- -0.5V) Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA Output Short Circuit Duration (Note 2). . . . . . . . . . . . . . . . Indefinite Operating Conditions Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Thermal Information
Thermal Resistance (Typical, Note 1) JA (oC/W) JC (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . 115 N/A Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
NOTES: 1. JA is measured with the component mounted on an evaluation PC board in free air. 2. Short Circuit may be applied to ground or to either supply.
Electrical Specifications
PARAMETER Input Offset Voltage Input Offset Current Input Current Large-Signal Voltage Gain
TA = 25oC, V+ = 15V, V- = 0V, Unless Otherwise Specified CA3160 SYMBOL |VIO| |IIO| II AOL TEST CONDITIONS VS = 7.5V VS = 7.5V VS = 7.5V VO = 10VP-P , RL = 2k MIN 50 94 TYP 6 0.5 5 320 110 90 -0.5 to 12 32 13.3 0.002 15 0 22 20 10 2 8 MAX 15 30 50 10 320 0.01 0.01 45 45 15 3 MIN 50 94 80 0 12 14.99 12 12 CA3160A TYP 2 0.5 5 320 110 95 -0.5 to 12 32 13.3 0.002 15 0 22 20 10 2 6 MAX 5 20 30 10 150 0.01 0.01 45 45 15 3 UNITS mV pA pA kV/V dB dB V V/V V V V V mA mA mA mA V/oC
Common-Mode Rejection Ratio Common-Mode Input-Voltage Range Power-Supply Rejection Ratio Maximum Output Voltage
IOM+ IOM-
I+
VIO/T
Electrical Specifications
PARAMETER
For Design Guidance, VSUPPLY = 7.5V, TA = 25oC, Unless Otherwise Specified CA3160 SYMBOL TEST CONDITIONS 10k Across Terminals 4 and 5 or Terminals 4 and 1 RI CI eN f = 1MHz BW = 0.2MHz RS = 1M RS = 10M TYP 22 1.5 4.3 40 50 72 30 CA3160A TYP 22 1.5 4.3 40 50 72 30 UNITS mV T pF V V nV/Hz nV/Hz
Input Offset Voltage Adjustment Range Input Resistance Input Capacitance Equivalent Input Noise Voltage
eN
RS = 100
1kHz 10kHz
CA3160, CA3160A
Electrical Specifications
PARAMETER Unity Gain Crossover Frequency Slew Rate Transient Response Rise and Fall Time Overshoot Settling Time For Design Guidance, VSUPPLY = 7.5V, TA = 25oC, Unless Otherwise Specified (Continued) CA3160 SYMBOL fT SR tr OS tS CL = 25pF, RL = 2k , (Voltage Follower) To <0.1%, VIN = 4VP-P CL = 25pF, RL = 2k , (Voltage Follower) TEST CONDITIONS TYP 4 10 0.09 10 1.8 CA3160A TYP 4 10 0.09 10 1.8 UNITS MHz V/s s % s
Electrical Specifications
PARAMETER Input Offset Voltage Input Offset Current Input Current Common-Mode Rejection Ratio Large Signal Voltage Gain
For Design Guidance, V+ = +5V, V- = 0V, TA = 25oC, Unless Otherwise Specified CA3160 SYMBOL VIO IIO Il CMRR AOL VO = 4VP-P , RL = 5k TEST CONDITIONS TYP 6 0.1 2 80 100 100 CA3160A TYP 2 0.1 2 90 100 100 0 to 2.8 300 500 200 UNITS mV pA pA dB kV/V dB V A A V/V
PSRR
VIO/V+
Block Diagram
7 200A 1.35mA 200A 8mA (NOTE 4) 0mA (NOTE 5) V+
NOTES: 4. Total supply voltage (for indicated voltage gains) = 15V with input terminals biased so that Terminal 6 potential is +7.5V above Terminal 4. 5. Total supply voltage (for indicated voltage gains) = 15V with output terminal driven to either supply rail.
BIAS CKT.
OUTPUT 6
V-
OFFSET NULL
Q1 D1 D2 D3 R1 40k R2 5k D4
Q2
Z1 8.3V
Q4
Q5
D6
D7
Q8 OUTPUT 6
Q7
R3 1k Q9
INV. INPUT
R5 1k
5 OFFSET NULL
8 STROBING
NOTE: Diodes D5 Through D7 Provide Gate Oxide Protection For MOSFET Input Stage.
Application Information
Circuit Description
Refer to the Block Diagram of the CA3160 series CMOS Operational Amplifiers. The input terminals may be operated down to 0.5V below the negative supply rail, and the output can be swung very close to either supply rail in many applications. Consequently, the CA3160 series circuits are ideal for single supply operation. Three class A amplifier stages, having the individual gain capability and current consumption shown in the Block Diagram provide the total gain of the CA3160. A biasing circuit provides two potentials for common use in the first and second stages. Terminals 8 and 1 can be used to supplement the internal phase compensation network if additional phase compensation or frequency roll-off is desired. Terminals 8 and 4 can also be used to strobe the output stage into a low quiescent current state. When Terminal 8 is tied to the negative supply rail (Terminal 4) by mechanical or electrical means, the output potential at Terminal 6 essentially rises to the positive supplyrail potential at Terminal 7. This condition of essentially zero current drain in the output stage under the strobed OFF condition can only be achieved when the ohmic load resistance presented to the amplifier is very high (e.g., when the amplifier output is used to drive MOS digital circuits in comparator applications). Input Stage - The circuit of the CA3160 is shown in the Schematic Diagram. It consists of a differential-input stage using PMOS field-effect transistors (Q6, Q7) working into a mirror-pair of bipolar transistors (Q9, Q10) functioning as load resistors together with resistors R3 through R6. The mirrorpair transistors also function as a differential-to-single-ended converter to provide base drive to the second-stage bipolar transistor (Q11). Offset nulling, when desired, can be effected by connecting a 100,000 potentiometer across Terminals 1 and 5 and the potentiometer slider arm to Terminal 4. Cascode-connected PMOS transistors Q2, Q4, are the constant-current source for the input stage. The biasing circuit for the constant-current source is subsequently described. The small diodes D5 through D7 provide gate-oxide protection against high-voltage transients, including static electricity during handling for Q6 and Q7. Second-Stage - Most of the voltage gain in the CA3160 is provided by the second amplifier stage, consisting of bipolar
CA3160, CA3160A
transistor Q11 and its cascode-connected load resistance provided by PMOS transistors Q3 and Q5. The source of bias potentials for these PMOS transistors is described later. Miller Effect compensation (roll off) is accomplished by means of the 30pF capacitor and 2k resistor connected between the base and collector of transistor Q11. These internal components provide sufficient compensation for unity gain operation in most applications. However, additional compensation, if desired, may be used between Terminals 1 and 8. Bias-Source Circuit - At total supply voltages, somewhat above 8.3V, resistor R2 and zener diode Z1 serve to establish a voltage of 8.3V across the series-connected circuit, consisting of resistor R1, diodes D1 through D4, and PMOS transistor Q1. A tap at the junction of resistor R1 and diode D4 provides a gate-bias potential of about 4.5V for PMOS transistors Q4 and Q5 with respect to Terminal 7. A potential of about 2.2V is developed across diode-connected PMOS transistor Q1 with respect to Terminal 7 to provide gate bias for PMOS transistors Q2 and Q3. It should be noted that Q1 is mirror-connected to both Q2 and Q3. Since transistors Q1, Q2, Q3 are designed to be identical, the approximately 200A current in Q1 establishes a similar current in Q2 and Q3 as constant-current sources for both the first and second amplifier stages, respectively. At total supply voltages somewhat less than 8.3V, zener diode Z1 becomes nonconductive and the potential, developed across series-connected R1, D1 - D4, and Q1, varies directly with variations in supply voltage. Consequently, the gate bias for Q4, Q5 and Q2, Q3 varies in accordance with supplyvoltage variations. This variation results in deterioration of the power-supply-rejection ratio (PSRR) at total supply voltages below 8.3V. Operation at total supply voltages below about 4.5V results in seriously degraded performance. Output Stage - The output stage consists of a drain-loaded inverting amplifier using CMOS transistors operating in the Class A mode. When operating into very high resistance loads, the output can be swung within millivolts of either supply rail. Because the output stage is a drain-loaded amplifier, its gain is dependent upon the load impedance. The transfer characteristics of the output stage for a load returned to the negative supply rail are shown in Figure 17. Typical op amp loads are readily driven by the output stage. Because largesignal excursions are non-linear, requiring feedback for good waveform reproduction, transient delays may be encountered. As a voltage follower, the amplifier can achieve 0.01% accuracy levels, including the negative supply rail.
Input Offset Voltage (VIO) Variation with DC Bias vs Device Operating Life
It is well known that the characteristics of a MOSFET device can change slightly when a DC gate-source bias potential is applied to the device for extended time periods. The magnitude of the change is increased at high temperatures. Users of the CA3160 should be alert to the possible impacts of this effect if the application of the device involves extended operation at high temperatures with a significant differential DC bias voltage applied across Terminals 2 and 3. Figure 25 shows typical data pertinent to shifts in offset voltage encountered with CA3160 devices in metal can packages during life testing. At lower temperatures (metal can and plastic) for example at 85oC, this change in voltage is considerably less. In typical linear applications where the differential voltage is small and symmetrical, these incremental changes are of about the same
Offset Nulling
Offset-voltage nulling is usually accomplished with a 100,000 potentiometer connected across Terminals 1 and 5 and with the potentiometer slider arm connected to Terminal 4. A fine offset-null adjustment usually can be effected with the slider arm positioned in the mid-point of the potentiometer's total range.
CA3160, CA3160A
magnitude as those encountered in an operational amplifier employing a bipolar transistor input stage. The 2V differential voltage example represents conditions when the amplifier output state is toggled, e.g., as in comparator applications. voltages. Figure 17 shows the voltage transfer characteristics of the output stage for several values of load resistance.
Wideband Noise
From the standpoint of low-noise performance considerations, the use of the CA3160 is most advantageous in applications where in the source resistance of the input signal is on the order of 1M or more. In this case, the total input-referred noise voltage is typically only 40V when the test circuit amplifier of Figure 2 is operated at a total supply voltage of 15V. This value of total input-referred noise remains essentially constant, even though the value of source resistance is raised by an order of magnitude. This characteristic is due to the fact that reactance of the input capacitance becomes a significant factor in shunting the source resistance. It should be noted, however, that for values of source resistance very much greater than 1M, the total noise voltage generated can be dominated by the thermal noise contributions of both the feedback and source resistors.
7 3 + Q8 CA3160
V+
RL 2
4 VNEGATIVE SUPPLY
FIGURE 1B. SINGLE POWER SUPPLY OPERATION FIGURE 1. CA3160 OUTPUT STAGE IN DUAL AND SINGLE POWER SUPPLY OPERATION
CA3160, CA3160A
+7.5V 0.01F 3 1M 2 7 + CA3160 6 4 0.01 F -7.5V BW (3dB) = 200kHz TOTAL NOISE VOLTAGE (INPUT REFERRED = 40V (TYP) 1k 30.1k NOISE VOLTAGE OUTPUT
RS
FIGURE 2. TEST CIRCUIT AMPLIFIER (30dB GAIN) USED FOR WIDEBAND NOISE MEASUREMENTS
2k
0.1F
FIGURE 3A.
Top Trace: Output Bottom Trace: Input FIGURE 3B. SMALL SIGNAL RESPONSE
Top Trace: Output Signal Center Trace: Difference Signal 5mV/Div. Bottom Trace: Input Signal FIGURE 3C. INPUT-OUTPUT DIFFERENCE SIGNAL SHOWING SETTLING TIME
FIGURE 4A.
Top Trace: Output Bottom Trace: Input FIGURE 4B. OUTPUT WAVEFORM WITH GROUND REFERENCE SINE WAVE INPUT
FIGURE 4C. OUTPUT SIGNAL WITH INPUT SIGNAL RAMPING FIGURE 4. SINGLE SUPPLY VOLTAGE FOLLOWER WITH ASSOCIATED WAVEFORMS. (E.G., FOR USE IN SINGLE SUPPLY D/A CONVERTER; SEE FIGURE 9 IN AN6080)
CA3160, CA3160A
10V LOGIC INPUTS +10.010V LSB 9 6 8 3 CD4007A SWITCHES 9 7 4 13 8 806K 1% 806K 1% VOLTAGE REGULATOR 2 CA3085 3 7 + 2F 25V 4 0.001F 6 1 8 22.1K 1% 1K REGULATED VOLTAGE ADJUST 3.83K 1% 1 5 402K 1% 200K 1% 12 13 8 100K 1% 806K 1% 7 10 2 CD4007A SWITCHES 1 5 1% 806K 1% 750K 1% 806K 1% 12 806K 13 8 (2) 806K 1% CD4007A SWITCHES 1 5 (4) 806K 1% (8) 806K 1% +15V PARALLELED RESISTORS OUTPUT 6 4 5 LOAD 100K OFFSET NULL 1 7 + CA3160 3 VOLTAGE FOLLOWER 2 10K 12 14 11 6 6 5 3 4 10 3 6 2 3 MSB 1 10
+15V
62 +10.010V
BIT 1 2 3 4 5 6-9
2K 0.1F
conditions such that EAVG = V1. This circuit condition is accomplished by feeding an output signal from Terminal 6 of A2 through R4, D4 to the inverting terminal (Terminal 2) of A1, thereby adjusting the multivibrator interval, T3.
Function Generator
A function generator having a wide tuning range is shown in Figure 9. The adjustment range, in excess of 1,000,000/1, is accomplished by a single potentiometer. Three operational amplifiers are utilized: a CA3160 as a voltage follower, a CA3080 as a high speed comparator, and a second CA3080A as a programmable current source. Three variable capacitors C1, C2, and C3 shape the triangular signal between 500kHz and 1MHz. Capacitors C4, C5, and the trimmer potentiometer in series with C5 maintain essentially constant (+10%) amplitude up to 1MHz.
CA3160, CA3160A
2N6385 POWER DARLINGTON 2 0.2F 2.4k 1W TURN ON DELAY 1 10k 1k OUTPUT 0V TO 35V AT 1A
3 40V INPUT +
100k
1.5k 1W
1k
1N914 2.2k 100F 25V + 7 + 5F 10 CA3086 11 2 2k 6 2N2102 9 7 6 3 5 4 1k 62k 5 1 12 14 13 50k 100k 10k 4.7k 4 8
10k + CA3160 3
2 8.2k
0.01F
Hum and Noise Output <250VRMS; Regulation (No Load to Full Load) <0.005%; Input Regulation <0.01%/V FIGURE 6. VOLTAGE REGULATOR CIRCUIT (0.1V TO 35V AT 1A)
T2 V +15V D1 T1 10K +15V 100K 3 R6 100K C1 500pF 2 D2 + MULTIVIBRATOR CA3130 7 +15V 0.1 F 6 R3 1M 4 C2 0.01F R1 182K R2 10K 3 2 EAVG = V T2/T1 T3 fO VCO CONTROL VOLTAGE (VI) (0V - 10V) (SENSITIVITY = 1kHz/V) 1M 0.01F R5 100K
7 6
0.01F
D3 D5
D4
R4 3K
D1 - D5 = 1N914
10
CA3160, CA3160A
BATTERY TEST OFF ON 3 POSITION SLIDE SWITCH + 500 F M 0-1mA 2.7k 6 4 5 1 300V 100V 30V 10V 100k ZERO ADJUST 9.1k SW1C 3V 1V 300mV 100mV 10k 30mV 10mV 100 900 9k 820 200 1V CAL. 3V CAL. 500 300V 100V 30V 10V 3V 1V 300mV 100mV 30mV 10mV SW1D
100M
1.02 M
10V
9.9k
3V 1V 300V 100V 30V 10V SW1B 3 22M 0.001F 2 +9V BATTERY 7 + CA3160 BATTERY
20pF
8.2k +7.5V VOLTAGE-CONTROLLED CURRENT SOURCE 7 3 1k 1k 2 2M SYMMETRY -7.5V 100k +7.5V + CA3080A 6 4 5 -7.5V 4.7k 10-80pF C2 6.2k 0.9 - 7pF C1
5 10k 2 7
4 - 60pF CA3160 C3 2 4
CA3080 6 -7.5V +
10k
50k C5 15 - 115pF
2-1N914
11
CA3160, CA3160A
NOTE: A square wave signal modulates the external sweeping input to produce 1Hz and 1MHz, showing the 1,000,000/1 frequency range of the Function Generator. FIGURE 9B. TWO-TONE OUTPUT SIGNAL FROM THE FUNCTION GENERATOR
NOTE: The bottom trace is the sweeping signal and the top trace is the actual generator output. The center trace displays the 1MHz signal via delayed oscilloscope triggering of the upper swept output signal. FIGURE 9C. TRIPLE-TRACE OF THE FUNCTION GENERATOR SWEEPING TO 1MHz
1N914
3 100 k
CA3160 + 4 6 2k
MULTIVIBRATOR
+15mV TO +10V
12
CA3160, CA3160A
Terminals 2 and 4 of the CA3160 at ground potential, the CA3160 input is operated in the guarded mode. Under this operating condition, even slight leakage resistance present between Terminals 3 and 2 or between Terminals 3 and 4 would result in zero voltage across this leakage resistance, thus substantially reducing the leakage current. If the CA3160 is operated with the same voltage on input Terminals 3 and 2 as on Terminal 4, a further reduction in the input current to the less than one picoampere level can be achieved as shown in Figure 23. To further enhance the stability of this circuit, the CA3160 can be operated with its output (Terminal 6) near ground, thus markedly reducing the dissipation by reducing the supply current to the device. The CA3140 stage serves as a X100 gain stage to provide the required plus and minus output swing for the meter and feedback network. A 100-to-1 voltage divider network consisting of a 9.9k resistor in series with a 100 resistor sets the voltage at the 10G resistor (in series with Terminal 3) to 30mV full-scale deflection. This 30mV signal results from 3V appearing at the top of the voltage divider network which also drives the meter circuitry. By utilizing a switching technique in the meter circuit and in the 9.9k and 100 network similar to that used in voltmeter circuit shown in Figure 8, a current range of 3pA to 1nA full scale can be handled with the single 10G resistor.
COMPARATOR OSCILLATOR
Top Trace: Staircase Output 2V Steps Center Trace: Comparator Bottom Trace: Oscillator FIGURE 10B. STAIRCASE GENERATOR WAVEFORM FIGURE 10. STAIRCASE GENERATOR CIRCUIT
Staircase Generator
Figure 10 shows a staircase generator circuit utilizing three CMOS operational amplifiers. Two CA3130s are used; one as a multivibrator, the other as a hysteresis switch. The third amplifier, a CA3160, is used as a linear staircase generator.
Picoammeter Circuit
Figure 11 is a current-to-voltage converter configuration utilizing a CA3160 and CA3140 to provide a picoampere meter for 13pA full scale meter deflection. By placing
10G
3 560k
-15V
-15V
FIGURE 11. CURRENT-TO-VOLTAGE CONVERTER TO PROVIDE A PICOAMMETER WITH 3pA FULL SCALE DEFLECTION
13
CA3160, CA3160A
+15V 100k +15V 2200pF 30pF 1M 3 + CA3160 2 6 8 4 5 1 100k OFFSET VOLTAGE ADJUST 9.1k 8.2k 0.1F 27k 500A STROBE INPUT 2k SAMPLE = 15V HOLD = 0V 5 DROOP ZERO ADJUST 39k 3 2 7 0.1F 0.1F 39k 7 6 100k 1M 3 0.1F 2 8.2 +15V
0.1F 7
1N914 +
CA3080A 4
CA3140 + 4 6
FIGURE 12A. SINGLE SUPPLY SAMPLE AND HOLD SYSTEM, INPUT 0V TO 10V
SAMPLED OUTPUT
INPUT SIGNAL
SAMPLING PULSES
SAMPLING PULSES
Top Trace: Sampled Output Center Trace: Input Signal Bottom Trace: Sampling Pulses FIGURE 12B. SAMPLE AND HOLD WAVEFORM
Top Trace: Sampled Output Center Trace: Input Signal Bottom Trace: Sampling Pulses FIGURE 12C. SAMPLE AND HOLD WAVEFORM
FIGURE 12. SINGLE SUPPLY SAMPLE AND HOLD SYSTEM, INPUT 0V TO 10V
hold mode. Even with 320mV at the amplifier bias circuit terminal (5) at least 1100pA of output current will be available.
14
CA3160, CA3160A
Operation with Output Stage Power Booster
R1 100k R3 51k C2 51pF 3 2 + CA3160 R2 100k C1 10-80 pF 6 4 2k 2-1N914 0.01F 680 f= 1 2 (R1 || R2) C1 R3 C2 500 7 +15V 0.1 F OUTPUT f = 100kHz 2% THD AT 1.1VP-P
The current sourcing and sinking capability of the CA3160 output stage is easily supplemented to provide power-boost capability. In the circuit of Figure 14, three CMOS transistorpairs in a single CA3600 lC array are shown parallel-connected with the output stage in the CA3160. In the Class A mode of CA3600E shown, a typical device consumes 20mA of supply current at 15V operation. This arrangement boosts the currenthandling capability of the CA3160 output stage by about 2.5X. The amplifier circuit in Figure 14 employs feedback to establish a closed-loop gain of 20dB. The typical largesignal-bandwidth (-3dB) is 190kHz.
+15V 0.01F 1M 1F CA3600 + 7 680k 3 INPUT 1F 2k 2 + CA3160 6 8 4 8 A = 20dB LARGE SIGNAL BW (-3dB) = 190kHz QN1 5 QN2 QN3 6 13 1 500F 3 10 12 50 100mW AT 10% THD QP1 QP2 QP3
14
11
7 20k
FIGURE 14. CMOS TRANSISTOR ARRAY (CA3600E) CONNECTED AS POWER BOOSTER IN THE OUTPUT STAGE OF THE CA3160
15
OL
150 200
60
40
CL = 30pF RL = 2k
20
0 101 102 103 104 105 106 FREQUENCY (Hz) 107 108
-50
50
100
TEMPERATURE (oC)
FIGURE 15. OPEN LOOP VOLTAGE GAIN AND PHASE SHIFT vs FREQUENCY
12.5
TA = 25oC RL = V- = 0
10.0
BALANCED VO = V+/2
7.5
5.0
HIGH VO = V+ OR LOW VO = V-
2.5
0 2.5 5 7.5 10 12.5 15 17.5 20 GATE VOLTAGE [TERMINALS 4 AND 8] (V) 22.5 6 8 10 12 14 16 18 POSITIVE SUPPLY VOLTAGE (V)
16
(Continued)
VOLTAGE DROP ACROSS PMOS OUTPUT STAGE TRANSISTOR (Q8) (V)
50 10
V- = 0V TA = 25oC
V+ = 15V 10V 5V
0.1
0.01
0.001 0.001
100
FIGURE 20. VOLTAGE ACROSS PMOS OUTPUT TRANSISTOR (Q8) vs LOAD CURRENT
1000 TA = 25oC VS = 7.5V
100 EN (nV/Hz) 10 0.01 1 0.01 0.1 1 10 100 1 101 MAGNITUDE OF LOAD CURRENT (mA) 102 103 FREQUENCY (Hz) 104 105 1
0.1
0.001 0.001
FIGURE 21. VOLTAGE ACROSS NMOS OUTPUT TRANSISTOR (Q12) vs LOAD CURRENT
17
(Continued)
4000
VS = 7.5V
1000 7.5 INPUT VOLTAGE (V) V+ 15V TO 5V 7 CA3160 3 2.5 VIN 4 8 0V TO V- -10V -1 0 1 2 3 4 5 6 INPUT CURRENT (pA) 7 6 INPUT CURRENT (pA)
100
5 PA
10
0 20 40 60 80 TEMPERATURE (oC)
7 OFFSET VOLTAGE SHIFT (mV) 6 5 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 4000 TIME (HOURS) DIFFERENTIAL DC VOLTAGE (ACROSS TERMINALS 2 AND 3) = 0V OUTPUT VOLTAGE = V+ / 2 DIFFERENTIAL DC VOLTAGE (ACROSS TERMINALS 2 AND 3) = 2V OUTPUT STAGE TOGGLED TA = 125oC FOR METAL CAN PACKAGES
18
MILLIMETERS MIN 0.39 2.93 0.356 1.15 0.204 9.01 0.13 7.62 6.10 MAX 5.33 4.95 0.558 1.77 0.355 10.16 8.25 7.11 NOTES 4 4 8, 10 5 5 6 5 6 7 4 9 Rev. 0 12/93
MIN 0.015 0.115 0.014 0.045 0.008 0.355 0.005 0.300 0.240
A A1 A2 B B1 C D D1 E
-C-
eA eC
C
C A B S
eB
NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the MO Series Symbol List in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
E1 e eA eB L N
2.93
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporations quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 19