Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Basic Glider Criteria Handbook

Download as pdf or txt
Download as pdf or txt
You are on page 1of 157
At a glance
Powered by AI
The document provides guidance for glider designers and operators to comply with airworthiness standards.

To provide guidance for glider designers, manufacturers and operators to comply with certification standards in addition to presenting acceptable compliance methods.

The Federal Aviation Agency's Flight Standards Service and the Soaring Society of America.

BASIC GLIDER CRITERIA

HANDBOOK

1962

Revision

Federal Aviation Agency


Flight Standards Service
Washington, D.C.

For sale by the Superintendent of Documents, U.S. Government Printing Office


Washington 25, D.C. - Price 75 cents

DEPOSITED BY THE
UNITED STATES OF AMERICA

12.-1

Preface
The purpose of the Basic Glider Criteria Handbook is to provide
individual glider designers, the glider industry, and glider operating
organizations with guidance material that augments the glider air
worthiness certification standards specified in Civil Air Eegulation
Part 5. Acceptable methods of showing compliance with the stand
Considerable material
ards are presented as compliance suggestions.
regarding common practices of construction and fabrication has been
included primarily for the information of novice builders and
designers, and should not be considered as the only satisfactory
practices.

This

edition incorporates minor revisions and corrections


dealing mainly with definitions of technical terms and symbols.
The content of the handbook remains unchanged.
The Basic Glider Criteria Handbook was prepared in the Federal
Aviation Agency, Flight Standards Service, by personnel of the
Acknowledgement is ex
Engineering and Manufacturing Division.
tended to the Soaring Society of America for their cooperation and
1962

advice.

in

utPOSlTEO 8Y THt
UNITED STATES OF AMERICA

Contents
Page

III

Preface
Introduction
Definitions

XIII

XV

Chapter I
Loads

Strength and deformations


Stiffness
Wing drag truss
Loads imparted by safety belts
Pilot and passenger loads
Local loads

1
1
1
2

2
2

Loading equilibrium
:
Flight loads

2
2

Design airspeeds
Load factors
Maneuvering load factors
Gust load factors

2
3

Factors
Symmetrical flight conditions (flaps retracted)
Basic flight envelopes
Symmetrical flight conditions (flaps or auxiliary devices in operation) . .
High-lift devices
Unsymmetrical flight conditions
Special flight conditions
Wing load distribution
Balancing loads
Control surface loads
Horizontal tail surfaces
Balancing
Maneuvering (horizontal surfaces)
Damping (horizontal stabilizer)
Loading for slab tail designs
Vertical tail surfaces
Maneuvering
Damping (vertical surfaces)
Gusts (vertical surfaces)
Ailerons
Maneuvering
Wing flaps
Special devices
Dive brakes
Control system loads
Elevator systems

3
5
5
5

10
10

H
13

13

20
23
28
28
29
29
30
31
31
31
31
31
31
31
32
32
33
33

CONTENTS Continued
Page

Rudder systems
Aileron systems
Flap and auxiliary control systems
Towing and launching (release mechanism) control systems
Ground loads
Level landing
Level landing with side load
Nose-down landing
Head-on landing
Wing-tip landing
Launching and towing loads
Loads on fittings
Wing truss strength
Multiplying factors of safety
Fittings
Castings

Parallel double wires

Wires at small angles

Double drag trusses


Torque tubes used as hinges
Control surface hinges and control system joints
Wire sizes
Wing lift trusses

34
34
34
35
35
35
36
37

38
39
40
41
41
41

43
43
43
43
43
44
44
44
44

Chapter 2
Proof of Structure

45
45
45
45
45

Determination of loadings
Control systems
Flight controls

Secondary controls
Fuselages

Weight distribution
Structural analysis as criteria of strength
Mechanical properties of materials
Proof of wings
Proof of control surfaces
Proof of control systems
Proof of landing gears
Shock absorption

Proof of fuselages
Combined structural analysis tests
Load tests
Special tests

System and component

tests

Test loads apparatus and methods


Methods of correcting to standard
Test procedures
Jigs
Loading schedule

45

45
46
46
46
47

47

48
48
49
49
50
50
50
51
53
53

53
53

Supports

54

VI

CONTENTS Continued
Page

Special procedure in limit load tests


Special procedure in ultimate load tests
Special procedures when ultimate load tests are conducted
stress analysis
Check of test structure
Test report
Wing tests
Rib tests
Selection of ribs
Wing of uniform chord
Tapered wing
Test loadings
Test methods
Wing proof and strength tests
Test loads
Test methods
General

Mounting
Chord component

54
54
55

55
57

57
57
57
57

57
60

60
60
60
60

60
61

Rigidity
Test report
Control surface tests

62
62

Tail

surface and aileron tests


Test loads
Kinds of tests
Load distribution-tail surfaces
Ailerons
Balance area
Test methods

Horns
Mounting
Fabric covering

62
62
62
62
62
62
62
62
62
62

67

Brace wires

67

Load application
Test report
Flap tests
Test methods and loads
Test report
Control system tests
Test loads

67
67
71
71
71
71
71

Operating test
Strength tests
Test methods
Method of load application

71
71
72
72

Application

74

Operation

test
Ultimate load test

Fuselage tests
Test loads

in lieu of

61

Deflections

Rigidity
Test report

54

74
74
74

74
75

75

VII

CONTENTS Continued
Page

Test methods

75
75
75
75
75
76
78
78
78
78
79

General

Bending test
Torsion test
Towing and launching loads
Test report
Flight load tests
Flutter and vibration prevention tests
Ground vibration tests
Simplified flutter criteria
Wing flutter criteria
Wing torsional stiffness
Aileron balance criterion
Free play of ailerons
Frequency of ailerons, dive brakes, or spoilers
Empennage flutter criteria
Elevator balance
Parallel axis criterion
Perpendicular axis criterion
Rudder balance
Tab flutter criteria
Balance weight attachment criteria
Flight flutter testing
Acceptability
Records
Test procedures

79
79

81
81
81
81
81
81

......
.
I

83
83
86
86
87
87
87

Chapter 3
Design, Construction and Fabrication
Processes
Wing design

Torsional stiffness
Wing design details.

Solid wood spars


Built-up wood spars
Splices in wood spars
Wood leading edge
Wood ribs

91

Wing spars

91

91
91

91
92
92

Trailing edges
Wing tips bows
External brace struts

Jury

89
89
89

95

95
95
95
96
96
97
97
99
99
100

struts

Wing fittings
Fabric covering
Metal covered wings
Control surfaces design
Control surface stops
Hinges

Installation
Elevators
Tabs

101
101

VIII

CONTENTS Continued
Page

Control systems design


Rigidity
Dual controls
Control system locks
Installation
Travel
Positioning

101
11
101
102
102
102
102

Centering
Stops
Hinges, bearings, and joints
Hinges
Bearings

102
102
102
102
103

Friction
Locking devices
Cockpit controls

103
103
103

Cables, pulleys and fairleads


Cables

103
103

Turnbuckles
Spring connecting links
Fairleads
Pulleys
Motions and clearances
Tension changes
Aerodynamic balancing

103
103
103
104
109
109
109

Creeping
Interference
Clearance
Nose wheel
Single cable controls
Spring devices
Flap controls
Tab controls

109
109
109
109
109
110
110
110

Position indicator
Reversibility
Wear and vibration
Degree of travel
Direction of operation
Landing gear design
Landing skids
Main skids
Shock absorption for skids
Skid design
Main gear

110
11O

HO
HO
110

111
111
111
111
111
111

Shock absorption
Wheel support structure
Brakes
Dual wheels
Fuselage design
Purpose
Nose
Landing gear
Ground angle and clearance

111
112
112
112
112

H2

112
112
112

IX

CONTENTS Continued
Page

Tail skid
Provisions for turn-over
Pilot and passenger compartments
Ventilation and visibility

112
112
113

H3

113
113
113

Seats

Pilot and passenger enclosures

Steel tube fuselages


General

H3

Load distribution
Diagonal

113
113

braces

Splices

H4
H4
H4

General

H4

Joints

Fairing
Plywood monocoque fuselages

114

Plywood sizes
Bulkheads
Curved monocoque type

H4

115

H5
H5

Rigidity

Concentrated loads
Crash protection
Tow cable release mechanisms

117

Chapter 4
H9

Equipment
Instruments and equipment
Contact (day) flight rules
Contact (night) flight rules
Instrument flight
Installation recommendations
Instruments
Airspeed indicator
Magnetic compass
Flight and navigation instruments

119

119

H9

120
120
120

120
120

Gyroscopic instruments
Safety equipment installation. Safety belts
Electrical equipment installation
Storage battery
Master switch
Circuit protective devices
Instrument lights
Position and anti-collision lights
Miscellaneous equipment installation
Seats

Flight Characteristics

120
120
120
120

i2l

121
121
121
121
121
121

Chapter 5
123

Controllability
Trim
Stability

123
123
123

CONTENTS Continued
Page

Stalls
Spins

124
124

Ground handling characteristics


Flutter and vibration
Flight tests
Test pilot qualifications
-Parachutes
Instrument calibration
Loading conditions
Single-place gliders
Two-place gliders
Two-place side-by-side

125
125
125
125
125
125
126
126
126

gliders

126

Ballast
Maximum airspeed
Airspeed indicator calibration
Operation limitations
Center of gravity limitations
Towing limitations
Airspeed limitations
Equipment limitations

Gliders With Power

126
127
127
127
127
127
127
128

Chapter 6

for Self Launching

Flight requirements
Structural requirements
Powerplant requirements

129
129
129
129

Scope and general design


Engines and propellers
Engines
Calibration test
Detonation test
Endurance test
Propellers
Propeller clearance
Fuel system
Arrangement
Fuel tanks
Fuel tank tests

129
130
130
130
130
130
130
131
131
131
131
131

Fuel tank installation


Fuel system lines and fittings
Fuel sumps
Fuel vents
Oil system
Oil tanks
Oil tank tests
Oil tank installation
Oil system lines and fittings
Oil breather lines

132
132
132
132
133
133
133
133
133
133

Cooling

133

Cooling test
Induction system
Induction system ducts

134
134
134

XI

CONTENTS Continued
Page

Induction system screens


Exhaust system
Exhaust manifold
Firewall and cowling

134
134

134

Firewalls
Firewall construction
Cowling
Retractable engine assembly
Power plant controls and accessories
Power plant controls
Throttle controls
Ignition switches
Mixture controls
Location
Markings
Construction
Movement
Accessories

Powerplant accessories
Equipment
Required basic equipment
Flight instruments
Powerplant instruments

135
135

135
135
135
135
135
135
135
136
136
136
136
136
136
136
136
136
136
137

Chapter 7
Miscellaneous Recommendations

139

General
Standard weights
Leveling means

139
139
139

XII

Introduction

The Basic Glider Criteria Handbook contains design recommenda


tions based on the present knowledge and development of glider
design. They may be used as the minimum standards for establish
ing the classifications and related airworthiness of both conventional
type gliders and those equipped with auxiliary powerplants.
New types of gliders and new materials and types of construction

may, however, incorporate features to which the recommendations


cannot be logically applied. In such cases, special consideration will
be given to the particular new problems involved.
In cases where deviation from the conventional is small, sufficient
evidence should be submitted to show that the proposed deviation
will not be detrimental to the airworthiness of the design. When the
deviation from the conventional is considerable, special recommen
dations covering the features in question should be obtained from
the Federal Aviation Agency.
Insofar as the recommendations are concerned, rotating wing, sea
plane and amphibian type gliders are considered unconventional.

Classification of Gliders
For the purpose of applying the recommendations, gliders are
classified on the basis of certain imposed operating limitations.

In

general, the various glider types can be classified as high per


formance or utility types.
A high performance or advanced type glider is especially designed
for the maximum performance within a selected range of conditions.
The utility type is a medium performance, nonacrobatic type of
glider designed for normal operations.
When doubt exists as to a particular glider's classification, the
basic flight envelope, together with a three-view drawing, should be
submitted to FAA so that a definite recommendation can be obtained.
(If acrobatics are contemplated, provisions should be made for in
stallation of parachutes, which are required for each occupant.)
Table 1-i
Glider Operating Limitations
Type of glider

High performance

Utility

"Never Exceed"

placard speed, m.p.h.

.90Vd (without
dive brakes).
.95Vd (with ap
propriate dive
1
brakes)
.90VC

1 See chapter 6, Airspeed

limitations.

Auto-winch tow

placard speed, m.p.h.

Airplane tow

Instrument
flying

.90V(

Permitted.

Permitted.'

Permitted-

Not

90V,
u

XIII

2 See chapter 4, Instrument flight.

per
mitted.

Glider Kits*

Gliders built from kits are eligible for FAA certification if sup
ported by a statement certifying that the glider was constructed in
accordance with FAA-approved drawings and the manufacturer's
manual of directions for building the glider ; and that the parts and
materials used, if other than those furnished with the kit, meet the
manufacturer's recommendations.
Also, the following inspections,
by FAA representative, and tests should be made.

Inspection for workmanship, materials and conformity prior


to installation of covering (plywood, metal, or fabric) on any
wing or control surface. (In general, any type of construc
tion may be "closed over" provided it is possible to conduct an
For ex
adequate inspection of critical parts subsequently.
ample, the interiors of monocoque construction should be in
spected prior to closing over unless adequate inspection open
ings are provided.)
A final inspection of the completed glider.
A check of flight characteristics.

Arrangement of Handbook
The material in Basic Glider Criteria Handbook has been arranged
so that the particular glider airworthiness recommendation is fol
lowed by the suggested methods for showing compliance. In cases
where methods for showing compliance are not needed, the airworthi
ness recommendation will have no accompanying guidance material.

Procedures and practices that assure safety equal to those listed


in this handbook will also be acceptable. Any provisions which are
shown to be inapplicable in a particular case will be modified upon
request and evaluation by the Federal Aviation Agency.
For further FAA guidance material on glider certificates, com
pliance procedures and related subjects, the following references are
listed :
Document

Technical Data Submittals


Inspection

and Tests

CAM

Design Changes

CAM
CAR

Repairs and Alterations


Foreign Imports
Identification and Marking
Flight Tests

CAM
CAM

1.73

1.68

1.10

1.25

1.30

5.14

CAM
CAM
CAR

1.60

10
1.100
1.15

Prior to beginning construction, it should be determined that the manufacturer


kit has obtained a type certificate for the prototype glider built from such a kit.

XIV

1.20

18
1

CAM
CAM

Type Certificates
Supplemental Type Certificates
Production Certificates

Section

CAM
CAM

Jjg

Subject

Airworthiness Certificates
Experimental Certificates
Restricted Certificates

of the

Definitions
TECHNICAL TERMS AND RELATED SYMBOLS
(For definitions

of nontechnical terms,

refer to Par. 1.1 of CAR Part 1)

Aerodynamic coefficients, CL, CM, Cp, et cetera. The coefficients


hereinafter specified are those of the "absolute" (nondimensional)
The subscripts
system adopted as standard in the United States.
N and C used herein refer respectively to directions normal to and
Other subscripts
parallel with the basic chord of the airfoil section.
have the usual significance. When applied to an entire wing or
surface, the coefficients represent average values and shall be properly
correlated with local conditions (wing load distribution) as required
in Chapter 1, p. 13. (See figs, i II, i
and i-IV.)

Air density, P. The mass density of the air through which the
glider is moving, in terms of the weight of a unit volume of air divided
by the acceleration due to gravity. The symbol denotes the mass
density of air at sea level under standard atmospheric conditions and
has a value of 0.002377 slugs per cubic foot. (See definition of
standard atmosphere.)
Balancing loads. Loads by which the glider is placed in a state of
equilibrium under the action of external forces resulting from speci
fied loading conditions. The state of equilibrium thus obtained may
be either real or fictitious.
Balancing loads may represent air loads,
inertia loads, or both.
Calibrated airspeed, CAS. Speed equal to the indicated airspeed
reading corrected for position and instrument error.
Design aircraft tow speed, V,a. The maximum indicated airspeed
at which the glider is to be towed by aircraft.
Design auto-winch tow speed, V,am- The maximum indicated air
speed at which the glider is assumed to be towed by automobile or
winch.
Design flap speed, Vf. The indicated airspeed at which maximum
operation of high-lift devices is chosen.
Design gliding speed, V,. The maximum indicated airspeed to be
used in the determination of gust loads.
Design gust velocity, U. A specific gust velocity assumed to act
normal to the flight path.
Design stalling speed, V,. The computed indicated airspeed in
unaccelerated flight based on the maximum lift coefficient of the wing
and the gross weight. When high-lift devices are in operation, the
corresponding stalling speed will be denoted by Ysf.

III

xv

cL

cR

Figures iII, i III and iIV.

Illustration of airfoil force coefficients.

Design wing area, S. The area enclosed by the projection of the


wing outline (including ailerons and flaps, but ignoring fairings and
fillets), on a surface containing the wing chords.
The outline is
assumed to extend through the fuselage to the plane of symmetry.
(See fig.

i-I.)

XVI

Design wing loading, s=W/S. The gross weight divided by the


design wing area.
(Area computed with wing flaps in retracted
position, if so equipped.)
Design dive speed, YD. The maximum indicated airspeed to be
used in the structural loading conditions and for which the glider is
demonstrated to be free from flutter or any other undesirable flight
characteristics. For utility category gliders VD shall not exceed Vf.
For high performance gliders, VD may exceed V, but shall not be
greater than 1.2 V.
Dynamic pressure, q. The kinetic energy of a unit volume of air.
= 3^ PV2 (in terms of true airspeed in feet per
second).
=
in
feet
terms
of
airspeed
equivalent
per second).
P0V2 (in
=
V2/39l pounds per square foot, when Vis miles per hour IAS.
Gross weight, W. The design maximum weight of the glider and
its contents, used for purposes of showing compliance with the speci
fied recommendations.

Indicated airspeed, IAS. Speed equal to the pitot static airspeed


indicator reading as installed without correction for system errors but
including sea level standard adiabatic compressible flow correction,
and instrument error.

Load factor or acceleration factor, n. The ratio of a force acting on a


mass to the weight of the mass.
When the force in question repre
sents the net external load acting on the glider in a given direction,
n represents the load factor or acceleration factor in that direction as
a multiple of the gravitational constant g.
Limit load. The maximum load anticipated in service.

Limit load

applied.
Never

test. A

exceed

speed,

static test in which the limit loads are properly


VOT. The maximum

indicated airspeed

for

which the glider is certificated for operation.


Primary structure. Those portions of the glider structure, the
failure of which would seriously endanger the airworthiness of the
glider.

Proof load. The prescribed externally-applied load, multiplied by


the proof factor (normally 1.0).
Standard atmosphere (standard air). Standard atmosphere refers
to that variation of air conditions with altitude which has been
adopted as standard in the United States.
(See NACA Technical
Report No. 218.)
Mean aerodynamic chord. The chord of an imaginary airfoil which
would have force vectors throughout the flight range identical with
those of the actual wing or wings.
Terminal velocity. The maximum speed obtainable in diving flight.
True airspeed, TAS. True airspeed of the glider relative to un
disturbed air.

xvn
657822O - 62 - 2

Ultimate factor of safety, j . A design factor used to provide for the


possibility of loads greater than those anticipated in normal conditions
of operation and for design uncertainties.

by shaded line

Figure iI. Typical design wing areas.

Ultimate load. The maximum load which the structure is required


It is obtained by multiplying the limit load by the
to support.
ultimate factor of safety.
Ultimate load test. A static test in which the ultimate loads are
properly applied. Loads should be supported for at least 3 seconds.

XVIII

Chapter

I LOADS

STRENGTH AND DEFORMATIONS

The primary structure should be capable of supporting the ultimate


loads determined by the loading conditions and ultimate factors of
safety specified herein, if the loads are properly applied and dis
tributed.
The structure must support these loads for a minimum
period of 3 seconds.
The primary structure should also be capable of supporting, without
detrimental permanent deformations, the limit loads of the loading
conditions specified, if the loads are properly distributed and applied.
In addition, temporary deformations that occur before the limit load
is reached should be such that repeated occurrence would not weaken
or damage the primary structure.

Compliance Suggestion

DETERMINATION OF DEFORMATION

Detrimental permanent deformations are usually considered as


those that correspond to stresses in excess of the yield stress.
The
yield is the stress at which the permanent strain is equal to 0.002
inches per inch from standard test specimens.

In determining permanent deformations from static

test results,
the effects of slippage or permanent deformation of the supporting
jig should be considered.

If

any deflections under load would change significantly the dis


tribution of external or internal loads, such distribution should be
taken into account.

The structure should

be capable of supporting limit


loads without suffering detrimental permanent deformations. At all
loads up to limit loads, the deformation should not interfere with
safe operation of the glider.
Wing drag truss. Fabric covered wing structures, having a canti
lever length of overhang such that the ratio of span overhang to the
chord at the root of the overhang is greater than 1.75, should have a
double system of internal drag trussing spaced as far apart as possible
or other means of providing equivalent torsional stiffness.
In the
former case, the counter wires should be of the same size as the drag
wires.
Stiffness.

Compliance Suggestion
CABLE

LIMITATIONS

Multistrand cables should not be used in drag trusses since they


stretch excessively.
Loads imparted by safety belts. Structures to which safety belts
are attached should be capable of withstanding the following ultimate
acceleration that occupants are assumed to be subjected to during
minor crash conditions :
Upward
4.5 g.
Forward

9.0 g.
3.0 g.

Sideward

If the belt is attached to the seat, the structural investigation


should be carried through to the primary structure. Also, the above
noted accelerations should be multiplied by a factor of 1.33 when
applied to the seat attachment to the structure.
Pilot and passenger loads. Pilot and passenger loads in the flight
conditions should be computed for a standard passenger weight of
A minimum ultimate factor of safety of 1.5 should be
170 pounds.
used in conjunction with the applicable acceleration or maneuvering
factor.
Local loads. -The primary structure should be designed to with
stand local loads caused by dead weights and control loads.
Baggage
and ballast compartments should be designed to withstand loads
corresponding to the maximum authorized capacity. Concentrated
(dead) weights include items such as batteries, radios, seats, et cetera.
Loading equilibrium. Unless provided for otherwise, the air and
ground loads should be placed in equilibrium with inertia forces,
considering all items of mass in the glider. All such loads may be
distributed in a manner conservatively approximating or closely
representing actual conditions.
FLIGHT LOADS
The airworthiness of a glider with respect to its strength under
flight loads usually is based on the airspeeds and accelerations (from
maneuvering or gusts) that can safely be developed in combination.
For certain types of gliders, the acceleration factors (specified in terms
of load factors) and gust velocities are arbitrarily specified and should
be used for these classes.
The airspeeds which can safely be devel
in
combination
with
the
oped
specified load factors and gusts should
be determined in accordance with the procedure specified, and they
should serve as a basis for restricting the operation of the glider in
flight.
Design airspeed. The design airspeeds should be selected so that
resulting operation limitations will be consistent with the type and
intended use of the glider. Minimum values for V, Vtaw and Vf are
specified in table 1-I.
2

Compliance Suggestion
DETERMINATION OF AIRSPEED

VALUES

The values of the design airspeeds in table 1-I are minimum values.

In certain cases it may be desirable to use larger values for high per
formance type gliders. In order to provide for a high auto-winch tow
placard speed, it may be advantageous to use a higher design gliding
speed.

Compliance Suggestion
USE OF K VALUES

The K values specified in table 1-I have been determined on the


basis of studies of the "cleanness" of current gliders. The values of

for high performance gliders have been set approximately H per


cent higher than the values of K for utility gliders since instrument

flying in high performance gliders is permitted and higher speeds are


These
apt to be encountered in recovery from inadvertent upsets.
attitudes are more likely to occur in instrument flying than in normal

Since these constants


operations under good weather conditions.
have been established on a simplified basis, it is possible that they
may lead to irrational values of V, when applied to particular cases.
In any event, it will be necessary to design high performance gliders
to a V greater than .40 times the terminal velocity or to design

utility gliders to a V, greater than

.36 times the

terminal velocity.

In

cases where the value of V is based on terminal velocity in accordance


with the above, calculations substantiating the terminal velocity

value should be submitted.

Load factors. The flight load factors specified should represent


wing load factors. The net load factor or acceleration factor should
be obtained by proper consideration of balancing loads acting on the

glider in the flight conditions specified in this chapter under "Maneuv


The net or dead weight load factors should be
ering load factors."
obtained from balancing computations such as are outlined under
"Balancing loads."
Maneuvering load factors. The limit maneuvering load factors
specified in table 1-I should be considered as minimum values unless

it can be proved that the glider embodies features of design which


make it impossible to develop such values in flight, in which case the
proven lower values may be used.

In

some cases

it may be advisable to use higher values,

higher auto-winch tow placard speed is desired.

as

when a

Gust load factors. The gust load factors should be computed on the
basis of a gust of the magnitude specified, acting normal to the flight
3

path. Proper allowance should be made for the effects of aspect


ratio on the slope of the lift curve. The following applies :

N = 1 +A n

where

+KUVm
575s

n = limit load factor increment


k =gust reduction factor (fig. 1-I)
7 = gust velocity, f.p.s.
V = indicated airspeed, m.p.h.
s =W/S, wing loading, p.s.f.
m = slope of lift curve, Cr, per radian corrected for aspect ratio, R.

u
<

NOTE:
bu

3
o

2
s =

K=\/2Sh

not exceed

W/S-WING LOADING, p.s.f.

Figure 11. Guft reduction factor.

1/2
1.0

(w/sr*

Factors of safety. A minimum

limit factor of safety of 1.0 and a


minimum ultimate factor of safety of 1.5 should be used unless other
Also, refer to p. 43 for multiplying factors of safety
wise specified.
required.
Table 1-1

Minimum Design Airspeeds and Minimum Limit Load Factors For the
Symmetrical Flight Conditions
High performance

Class of glider

Positive Auto-Winch
Tow
Load Factor.
Negative Maneuver Load FacFactor, n.
Negative Gust Load Factor 6_.

7.
8.
9.

10. Design

Dive Speed, Vp.

35(s)^

35(s)H.

1.67

5.33

Vsf

1.67 Vsf.

4.67.

Corresponding
(4).

-2.67

-2.33.

Corresponding to
24 f.p.s. ,rdown"
gust at V,.
Not to exceed 1,2 V,.

Corresponding to a 24
f.p.s. "down" gust
at V.
Not to exceed V,.

"

f^p.s.

to

> >

for

Utility

High performance

For gliders of very clean design


with cantilever wings.
For gliders of clean design having
single strut braced wings.
For gliders of the utility type hav
ing double strut braced wings

24

"up" gust at

The design gliding speed, V shall not be less than the design aircraft tow speed Vu.
conservative Interpolation of the value of
The following value of K should be used; however
particular design will be acceptable:
Glider configuration

to a
Corresponding
24 f.p.s. "up" gust
at V.

6.

K(s)H.

Positive Maneuver Load Fac


tor, n.
Positive Gust Load Factor *

5.

K(s)H

()

Design Gliding Speed 1


(V, m.p.h.).
Auto- Winch
Tow
3. Design
Speed, Vio, m.p.h.
4. Design Flap Speed Vf, m.p.h...

2.

Utility

61

55.

56

50.

51

46.

Positive Oust Load Factor: n=l+

n=l+

KUV.m
676a

K24V,m
676s
1

'

and open cockpit.

Positive Auto-Winch Tow Load Factor:

[^""'-e]

where s=des. wing loading, p.s.f.


e=unit wing weight, p.s.f.
V,.= Item of table 1-

Is

The factor 391 above


based on
value of 1.0 which experience indicates
likely to be reached when auto or winch towing the glider.
K24 V.m
Negative Oust Load Factor: n=l-

to be the maximum

value

676s

SYMMETRICAL

FLIGHT CONDITIONS

(Flaps Retracted)

is

Basic flight envelopes. The basic flight envelope or V-n diagram


locus of points representing the limit wing load factors and the
corresponding velocities for the particular design criteria.

Compliance Suggestion

DETERMINING FLIGHT

ENVELOPE

sample basic flight envelope is shown in fig. 1-II.


This envelope
has been constructed for a high performance sailplane of aero-

"clean" design, having


basic design values as follows:
dynamically

full cantilever wing, with

W/S=s=3.5 lbs. persq. ft.


R (Aspect Ratio) - 12

R of 12) =4.8 Cl per radian


(weight of wing) =1.5 lbs. per sq. ft.

m (Corrected to

with table 1-I, a value of K=61 was used so


that the minimum design gliding speed which was used was 61 Vs =
H4 m.p.h. (Vmn).
The corresponding placard "never exceed"
In this
speed would be .9x114 = 103 m.p.h.
(From fig. 1-I.)
particular case, however, it is assumed by the designer that a some
what higher placard "never exceed" speed is desirable so a design
Vs of 125 m.p.h. is selected making the corresponding placard speed
H2 m.p.h. (.9x125).
b. Plot the following equation to obtain line 1 of the positive
portion of the V-n diagram. (See fig. 1- II.)
_ V2CLmax where n = maximum possible positive limit wing
391 s
load factor at the speed V (m.p.h.).
c. Draw a vertical line through the velocity corresponding to V
(line 2 of fig. 1-II).
d. Plot the following equation to obtain line 3 of the negative
portion of the V-n diagram (see fig. 1-II) .
where n = maximum possible negative unit wing
_ V2
load factor at the speed V (m-p.h.). This is
391 s
based on a CL max. (dynamic) of 1.0 (negative).
e. When
applying the recommendations specified above, the
following procedure should be followed :
1. Draw a straight line (line 4 of fig. 1- III) from the point where
=
F 0, and n = l to the point where V = VC and n=the load factor
This will intersect line 2 at point E.
specified in item 6 of table 1-I.
2. Draw a horizontal line (line 5 of fig. 1-II) through the greatest
value of n specified in items 5 and 7 of table 1-I. This will intersect
line 1 at point C; and it will intersect line 4 at point D, providing the
positive gust load factor is greater than the maneuvering load factor.
If the maneuvering load factor is greater than the positive gust load
factor, line 5 will intersect witn line 2.
a.

In

Example

accordance

Item
Item

5.
6.

The specified maneuver load factor =5.33


The gust reduction factor from fig. 1-I is
s =3.5) so for this example:
n

1+

.685 x 24 x 125 x 4.8

575^5

on
nn
1+4-90=5.90
, .

.685

(for

Item

Vuuc =35 (3.5)% =65.5

7.

m.p.h.
4.75

The greatest positive load factor of items 5 and 7 above is 5.33 and it
therefore determines line 5 of the basic flight envelope of fig. 1-II.
It should be noted that the positive portion of the basic flight envelope
is represented by the points OCDEF of fig. l-II.

/. Draw

l-II)

from the point where


=
V=
V and n = the load factor
This will intersect line 2 at point 6.
specified in item 9 of table 1-I.
g. Draw a horizontal straight line (line 7 of fig. l-II) through the
negative value of n specified in item 8 of table 1-I. This will intersect
line 3 at point
and will intersect line 6 at point H providing the
a straight line (line 6 of fig.
0 and n = + 1 to the point where V

negative gust load factor is greater than the maneuvering load factor.
If the negative maneuvering load factor is greater than the negative
gust factor, line 7 will intersect with line 2.
Example

Item

8.

The specified maneuver load factor

Item

9.

The negative load factor due


follows

to

-2.67
down

gust is

as

.685 x 24 x 125 x 4.8


575 x 3.5

1-4.90=3.90

It

should be noted that the negative portion of the basic flight


envelope is represented by the points FGHJO of fig. l-II.

The glider need not be investigated for gust loads at speeds


higher than V. For Vd higher than V, in high performance gliders
only, but not to exceed 1.2 V the right hand corner of the V-n dia
h.

gram

need only be investigated for the maneuvering load factors.

This portion of the V-n diagram is established


1.

fig.
2.

l-II).

Draw a straight line (line


8 at

n =5.33 (point

K)

of fig.

l-II)

1.2 V0)

from point
of table 1-I).

(line

of

to intersect

(item 5
Draw a straight line (line 10 of fig. l-II) from point G to inter
sect line 8 at n=2.67 (point L) (item 8 of table 1-I).
This
additional portion of the V-n envelope is represented by the
points

i.

follows:

Draw a vertical line at VD max. (not to exceed

line

3.

as

In

EKLG.

general, an investigation of the following specific basic flight

conditions, which correspond to points on the basic flight envelope,

will insure satisfactory coverage of the critical loading conditions.


8

1.

Condition I. (Positive High Angle of Attack.)


This condition corresponds to point C on the basic flight
The aerodynamic characteristics C, CP. (or Cm),
envelope.
and C to be used in the investigation should be determined as
follows :
where nt =Wing load factor corresp. to pt. C
n nT8

Dynamic pressure corresp. to the


velocity Vr, which in turn corresp. to
point C.
=value corresp.
Ce = value corresp. to
to Cr as deter
Cn, as obtained
from the airfoil
mined from the air
characteristics
foil characteristics
qr =

CP.

or

Cm

curves.

curves.

Condition II. (Negative High Angle of Attack.)

This condition corresponds to point

envelope.
(a)
(b)
(c)

on the

basic

flight

a"II _nns
'

value corresp. to CnrI (may be assumed equal to zero


if positive) .
CP. or Cm value corresp. to CNn.
Ce =

-.16
CM

- MOMENT COEFFICIENT

OF BASIC WING

Figure 1III. Corrected moment coefficient for condition


9

ill;.

3.

III.

(Positive Low Angle of Attack.)


Condition
This condition corresponds to point E on the basic flight
envelope.

W CUI

-
9.111

qm=q,
Cc = value corresp. to CnlII (may be assumed equal to zero if
positive).
(c) CP. or Cm = value corresp. to CnrII
4. Condition IIIZ. (Modified Positive Low Angle of Attack.)
In order to cover the effects of limited use of the ailerons at V
on the wings and wing bracing, such structure should be investi
gated for the following:
(f>)

(b)

Ce =

(c)

Cm'

value corresp. to
CNrIIr
= value obtained from fig. 1-

III

is the value
need only be applied to that
corresp. to CNrII.
portion of the span incorporating ailerons, using the
basic value of Cm determined in Condition
over
the remainder of the span.

CJ

where

Cm

III

5.

Condition IV. (Negative Low angle of Attack.)


This condition corresponds to point G on the basic flight en
The aerodynamic characteristics should be determined
velope.
as follows :

W
(6)
(c)

Cnrv

iiv

value corresp. to CIV (may be equal to zero if positive)


CP. or Cm = value corresp. to (7/v.
Cc

SYMMETRICAL
High-lift

FLIGHT CONDITIONS

(Flaps or Auxiliary Devices in Operation)

When

flaps or other auxilliary high-lift devices


are installed on the wings, suitable provisions should be made to
devices.

account for their use in flight at the design flap speed Vf. Minimum
values of the design flap speed are specified in table 1-I. These
provisions should be based on the intended use of such devices.

Compliance Suggestion

INSTALLATIONS ON INTERNALLY BRACED

WINGS

For internally braced wings, the effects of trailing edge flaps on the

wing structure as a whole, can, in general, be satisfactorily accounted


for by modifying, when necessary, the basic flight conditions in the
following manner :
and IV
The average value of Cm' used in design Conditions
or
should equal
exceed the quantity :

III

10

where :

is the average moment coefficient about the aerodynamic


center (or at zero lift) for the airfoil section with flap com
Cmf

The average moment coefficient refers to a


pletely extended.
weighted average over the span when Cm is variable.
(The
is
wing area affected should be used in the weighting.)
Vf the
design speed with flaps extended.
V is the design gliding
and IV.
speed used in Conditions

III

Compliance Suggestion
COMPUTATIONS

NECESSARY

When the above provisions are made, no balancing computations


for the extended flap conditions need be submitted; hence these con
ditions can also be eliminated from the design of the horizontal tail
surfaces.

The foregoing interpretation applies to normal installations in


which the flap is inboard of the ailerons, or in which a full span
flap is used and the flap is intended for conventional use, i.e., the
relatively low speeds of approach and landing. For other arrange
ments it will be necessary to submit additional computations if it is
desired to prove that flap conditions are not critical.

In

all cases an investigation is required of the local wing structure


to which the flap is attached, using the flap design loads as deter

mined.

The strength of special wing ribs used with split flaps, and

the effect of flap control forces, should also be investigated.


Refer
ence should be made to current NACA reports for acceptable flap
data.

In

UNSYMMETRICAL

FLIGHT CONDITIONS

the required investigation for the effects of unsymmetrical flight


loads, the following assumptions should be made :

Modify Conditions

I and III (Chap.

pp. 9, 10) and the most critical


negative condition by assuming 100 percent of the air load to be
acting on one side of the glider and 40 percent on the other.
1,

Assume the moment of inertia of the entire glider is effective.

It will usually be convenient to separate the effects of the loads due


to linear accelerations from the loads due to torque (T). It may be
assumed that the stresses due to unsymmetrical loads can be obtained
by adding algebraically the stresses due to 70 percent of the normal
(symmetrical) loading to those determined by considering 30 percent
of the normal total load to be acting upward on one wing panel and
30 percent to be acting downward on the other. The unbalanced
moment or torque is caused by the differential of 60 percent of the
normal total load on one wing panel times the distance from the
longitudinal axis to the centroid of the load normally acting on the
panel.

(See fig.

1-IV.)

11

100%

_L_
NOTE:

ED

JlZft

d = centroid of loading.

100%

70%

70%

-30%

NOTE:
where:

T=.60xd
W=the normal

load on one panel .

Figure 1IV. Span load dislribulion

tor unsymmotrical night conditions.

The angular acceleration "a" resulting from the torque

be obtained as follows

"T" may

T_ (rad/sec.2)

the moment of inertia of the glider (and contents) about


the X, or longitudinal axis.
Iz is in mass units, and may
be computed in accordance with the procedure in NACA
Technical Note No. 575.
The torque T resisted by any portion of the glider may be obtained
from the following, assuming the angular acceleration to be constant
for all parts of the glider:
where Ix

when Ix

MN

dN2

Ia

where

(ft. lbs.)

MN =the mass of part

distance from the longi


tudinal axis to the CG of part

dN = the

iVin feet.
12

SPECIAL FLIGHT CONDITIONS

Wing load distribution. The limit air loads and inertia loads acting
on the wing structure should be distributed and applied in a manner
closely approximating the actual distribution in flight.

Compliance Suggestion

SPAN DISTRIBUTION

DETERMINATION

if

is,

(a) For wings having mean taper ratios equal to or greater than
.33, the span distribution should be determined as follows:
the zero
1. If the wing does not have aerodynamic twist (that

lift lines of all sections are parallel), the span distribution for

it

is

is

it

normal force coefficient (CN) should be assumed to vary in


accordance with figs. 1-V and 1-VI, which are assumed to
Each case should
represent two extreme cases of tip loading.
demonstrated that only one
critical.
be investigated, unless
will be acceptable to investigate
As an alternative method,
each design condition for only one span distribution using a
rational distribution, except in the case of the high-angle-ofattack condition which gives the maximum forward chord loads
(Condition I). For this condition the analysis should be made
for both the rational distribution and that given in fig. 1-V.

No

Figure 1V. Span distribution

tip loss.

"N

STATION WHERE
CHORD = DISTANCE
TO EXTREME TIP
Figure 1VI. Span distribution

tip loss.

and 1VI. Span distribution of CN for wings.

Figures 1

With

13

If the wing has aerodynamic twist, the span distribution should


be determined by the alternative method given in 1, above.
3. For these purposes, the mean taper ratio is defined as the ratio
2.

4.

of the tip chord (obtained by extending the leading and trailing


edges to the extreme wing tip) to the root chord (obtained by
extending the leading and trailing edges to the plane of sym
metry) .
Acceptable methods of determining a rational span distribution
are given in publication ANC-1 "Span wise Air Load Distribu
tion," and in NACA Technical Report Nos. 572, 585 and 606.

b. For all wings having mean taper ratios less than .33 the span
distribution should be determined by rational methods, unless it is
shown that a more severe distribution has been used. Acceptable
methods of determining rational span distribution are given in the
aforementioned documents of a, 4, above.

c.

When the normal force coefficient

is assumed to vary over the

span, the value used should be adjusted to give the same total normal
force as the design value of Cn acting uniformly over the span.

d. When figs. 1-V and 1-VI are used, the chord coefficient should be
assumed to be constant along the span.
e.

For wings having aerodynamic twist (not geometric twist), it is

very important that the effect of twist (wash-out) be considered in the


investigation of the wings for the negative conditions.

Compliance Suggestion
DETERMINING CHORD

DISTRIBUTION

The approximate method of chord loadings outlined under "Rib


Tests" in Chapter 2 for the testing of wing ribs is suitable for conven
tional two-spar construction if the rib forms a complete truss between
a.

An investigation of the actual chord


loading should be made in the case of stressed-skin wings if the longi
the leading and trailing edges.

In some cases
tudinal stiffeners are used to support direct air loads.
it is necessary to determine the actual distribution, not only for total
load but for each surface of the wing. If wind tunnel data are not
available, the methods outlined in

456, 631, and

NACA Reports Nos.

634 are suitable for this purpose.

383,

4H,

These methods

consist of determining the "basic" pressure distribution curve at the


"ideal" angle of attack and the "additional" pressure distribution
curve for the additional angle of attack. These curves can be coordi
nated with certain values of CL so that the final pressure distribution
curve can be obtained immediately for any CL.
Curves of this nature
for several widely used air foils can be obtained directly from the

NACA.

14

b. On high speed gliders the leading edge loads developed may be


exceptionally severe, particularly the "down" loads which are pro
duced by negative gusts when the glider is flying at the design gliding
The magnitude of such loads can be estimated without
speed.
determining the entire chord distribution by the method outlined in
NACA Keport No. 413.

When a design speed higher than required is used in connection


with wing flaps or other auxiliary devices it will be necessary to
determine the chord distribution over the entire airfoil. The effect
of any device which remains operative up to V, should be carefully
This applies particularly to auxiliary airfoils, spoilers,
investigated.
and fixed slots.
c.

Compliance Suggestion

DETERMINATION

OF RESULTANT

AIR FORCES

A general method is outlined below for determining the mean


effective value of the normal force coefficient, the average moment

coefficient, location of the mean aerodynamic center and value of the


mean aerodynamic chord. These factors are needed in order to
determine the balancing loads for various flight conditions. The
most general case will be considered, so that certain steps can be
omitted when simpler wing forms or span load distribution curves are
involved.

In

general, the summation of all forces acting on a wing can be


expressed as a single resultant force acting at a certain point. If the
a.

point is so chosen that, at constant dynamic pressure, the moment of


the air forces does not appreciably change with a change in the angle
of attack of the airfoil, the point can be considered as the mean aero
dynamic center of the wing. The resultant force can be resolved into
the normal and chord components and represented by the average
coefficient, CN and Cc, while the moment is represented by the average
moment coefficient, Cm, multiplied by a distance which can be con
sidered to be the mean aerodynamic chord. The values of the above
quantities and the location of the mean aerodynamic center will
depend on the plan-form of the wing and the type of span distribution
curve used.

b. For convenience and clarification, table 1-Ia has been developed


and the various curves obtained as a part of this method are illustrated
in figs. 1-VII, 1-VIII, and 1-IX. It should be particularly noted
that when the area under a curve is referred to, the area should be

expressed in terms of the product of the units (coordinates) to which


the curve is drawn. The procedure is as follows:
1.

Fig. 1-VII illustrates the actual wing planform, plotted to a


suitable scale. This should agree with the definition of design
wing area.
15

657822 O - 62 - 3

Table 1-Ia

Determination of Resultant Air Forces


Root

No.
(1)

Span=b

(2)

Chord=C

(3)

(4)

RC=(3) x (2)

(S)

RkC

(6)

(7)

R,Cx=(4)

(8)

C>=(2)

(9)

SEMI-SPAN

Tip

b = (4) x (1)

x (6)

Cm C>=(9) x (8)

(10)

MAC=
2.

span.

3.

4.

1-VII

(6), shows the variation of wing chord, C, with the


The values of C are entered in table 1-Ia as item (2).
The area of the figure should be accurately determined and
converted to the proper units. It should be one-half the value
of design wing area.

Fig.

Fig. 1-VII (c), represents an assumed span distribution curve.


The factor Rb represents the ratio of the actual C at any point
to the value of Co at the root of the wing. Values of Rb from
this curve are entered in table 1-Ia under item (3) .

1-VII

(d), is obtained by plotting RbC (item (4)) in table


The ordinates of this curve are proportional
to the actual force distribution over the span.
The area under

Fig.

1-Ia against span.

1-VII

(d) should be accurately determined and expressed


in the proper units. Kt) the ratio of the mean effective CN to
the value of Co (at the root), is obtained by dividing the area
curve

under curve 1-VII (d) by the area under curve 1-VII (6) , using
the same units of measurement for each area.
This value of
Kb is indicated by the dotted line on curve 1-VII (c) .

5.

To determine the location of the mean aerodynamic center along

1-VIII

The ordinates are obtained by


multiplying the ordinates of curve 1-VII (d) by their distance
along the span, as shown in item (5), of table 1-Ia. The area
under curve 1-VIII (a), divided by the area under curve 1-VII
the span, fig.

(d)

is drawn.

gives the distance from the wing root to the chord on which

This

the mean aerodynamic center of the wing panel is located.


distance is indicated on fig.

1-VII

16

(a) by the dimension

b.

6.

The locus of the aerodynamic centers of each individual wing

chord is plotted on fig. 1-VII (a) as the dotted line A-B. In


table 1-Ia the distance "x" from the base line O-E to the line
A-B is entered under item (6) .

Figure 1-VII.

7.

Determination of effective normal force coefficient.

1-VIII

is now plotted, using as ordinates the values of


R Cz obtained from item (7) of table 1-Ia. The area under
curve 1-VIII (6), divided by the area under curve 1-VII (d),
gives the distance of the mean aerodynamic center from the base

Fig.

line O-E in fig.


that figure.

1-VII

(a)

This distance is indicated

17

as x on

8.

If it

is assumed that the moment coefficient about the aerody


namic center of each individual chord is constant over the span,
the magnitude of the mean aerodynamic chord is determined
by means of fig. 1-VIII (c). The ordinates for this curve are

Figure 1

determined from item (8) of table 1-Ia. The area under curve
1-VIII (c), divided by the area under curve 1-VII (c), gives
the value of the mean aerodynamic chord. By way of illustra
tion, it is drawn on fig. 1-VII (a) , so that its aerodynamic center
coincides with the location of the mean aerodynamic center of
the wing panel.

(a)

Figure 1IX. Determination of mean effective moment coefficient.

9.

In

cases in which wing flaps or other auxiliary high-lift devices


are used over a portion of the span it is desirable to obtain the
mean effective moment coefficient.
This is the coefficient to

in connection with the mean


aerodynamic chord previously determined under the assump
tion of a uniform moment coefficient distribution.
In table
1-Ia under item (9) the local values of the moment coefficient
be used for balancing purposes

19

These are also


about the aerodynamic center are entered.
plotted as fig. 1-IX, a, to illustrate a type of distribution which
might exist.
10. Fig. 1-IX (b) is plotted from the values indicated under item
(10) of table 1-Ia. The area under this curve divided by the
area under curve 1-VIII (c) gives the mean effective value of
the moment coefficient for the entire wing panel.
11. In the case of twisted wings a different span distribution exists
for each angle of attack. The location of the resultant forces
can, however, be determined in the above manner for any
known span distribution.

BALANCING LOADS

The balancing loads referred to in this chapter should be computed


by a rational method or by a suitable arbitrary method.

Compliance Suggestion
METHOD OF ANALYSIS

a. The basic design conditions must be converted into conditions


representing the external loads applied to the glider before a complete

structural analysis can be made.


This process is commonly referred
to as "balancing" the glider and the final condition is referred to as a
condition of "equilibrium."
Actually, the glider is in equilibrium
only in steady unaccelerated (constant speed) flight; in accelerated
conditions both linear and angular accelerations change the velocity
and attitude of the glider. It is customary to represent a dynamic
condition, for structural purposes, as a static condition by the expedi
ent of assigning to each item of mass the increased force with which it
resists acceleration.
Thus, if the total load acting on the glider in a
certain direction is "n" times the total weight of the glider, each item
of mass in the glider is assumed to act on the glider structure in exactly
the opposite direction and with a force equal to "n" times its weight.
b. If then the resultant moment of the air forces acting on the glider
is not zero with respect to the center of gravity, an angular accelera
tion results.
An exact analysis would require the computation of
this angular acceleration and its application to each item of mass in
the glider.
In general, such an analysis is not necessary except in
certain cases for unsymmetrical flight conditions. The usual expedi
ent in the case of the symmetrical flight conditions is to eliminate the
effects of the unbalanced couple by applying a balancing load near the
tail of the glider in such a way that the moment of the total force
about the center of gravity is reduced to zero. This method is par
ticularly convenient, as the balancing tail load can then be thought
of either as an aerodynamic force from the tail surfaces or as a part of
a couple approximately representing the angular inertia forces of the
masses of and in the glider. Considering a gust condition, it is proba
20

ble that angular inertia forces initially resist most of the unbalanced
couple added by the gust, while in a more or less steady pull-up con
dition the balancing tail load may consist entirely of a balancing air
load from the tail surfaces.

Compliance Suggestion
BALANCING THE GLIDER

a.
1.

The following considerations are involved in balancing the glider:


It is assumed that the limit load factors specified for the basic

flight conditions Chap. 1, p. 9 are wing load factors. A solution


is therefore made for the net load factor acting on the whole
glider. The value so determined can then be used in connection
with each item of weight (or with each group of items) in analyz
For balancing purposes the net factor is
ing the fuselage.
assumed to act at the center of gravity of the glider.

a = angle of attack,

degrees (shown

gliding angle, degrees.

positive).

n = force/W (positive upward and rearward).


m = moment/W (positive clockwise
as shown).
X = horizontal distance from I (positive rearward).
h = vertical
distance from I (positive upward).

All distances are expressed in

terms

of

the

Figure 1X. Basic forces in flight conditions.

21

M.A.C.

it is possible for a load to be acting in the opposite


direction on the elevator, it is recommended that the center of

2. Assuming that

pressure of the horizontal tail be placed at 20 percent of the


mean chord of the entire tail surface.
This arbitrary location

may also be considered as the point of application of inertia


forces resulting from angular acceleration, thus simplifying the
balancing process.
3. In fig. 1-X the external forces are assumed to be acting at three
points only. The assumption can generally be made that the
When more accurate
fuselage drag acts at the center of gravity.
data are available, the resultant fuselage drag force can of course
be computed and applied at the proper point.
Where large
independent items having considerable drag are present it is
advisable to extend the arrangement of forces shown in fig. 1-X
to include the additional external forces.
6. As shown in fig. 1-X, a convenient reference axis is the basic
chord line of the mean aerodynamic wing chord. (The basic chord
line is usually specified along with the dimensions of the airfoil
section.) The determination of the size and location of the mean
aerodynamic chord is outlined in Chap. 1, p. 15.
c. A tabular form will simplify the computations required to obtain
the balancing loads for various flight conditions.
A typical form for
this purpose is shown in table 1- II on p. 80.
In using fig. 1-X and
the following assumptions and conventions should be
table 1employed

II
:

Careful attention should be paid to those footnotes of fig. 1-X


which pertain to the sign convention that has been adopted. If
known forces are opposite in direction from those shown in fig.
1-X, a negative sign should be prefixed before inserting in the
In particular, it should be noted that the verti
computations.
cal distance, h2, is negative when the wing aerodynamic center
is above the CG, and positive when the wing aerodynamic
The direction of unknown forces will
center is below the CG.
be indicated by the sign of the value obtained from the equa
tions.
A negative value of n3 will usually be determined from
For
the balancing process, indicating a down load on the tail.
conditions of positive acceleration the solution should give a
negative value for n2, as the inertia load will be acting down
ward. The convention for mi corresponds to that used for
when the value of CM
negative
moment coefficients; that
diving moment.
mi should also be negative, indicating
2. All distances should be divided by the mean aerodynamic chord
before being used in the computations.
3. The chord load acting at the tail surfaces may be neglected.
indicated
In table 1the computation of balancing loads
for typical flight conditions. The equations are based on the fact
that the use of the average force coefficients in connection with the

II

is

d.

is

is,

1.

22

design wing area, mean aerodynamic chord, and mean aerodynamic


center will give resultant forces and moments of the proper magnitude,
Provision is made in the table for obtaining
direction and location.
the balancing loads for different design weights. The table may be
expanded to include computations for several loading conditions,
special flight conditions, or conditions involving the use of auxiliary
devices.
It should be noted that a change in the location of the CG
will require a corresponding change in the values of x2 and hi on fig.
1-X. (Condition IV will usually result in the largest balancing tail

load.)

When the full-load center of gravity position varies appreciably


the glider should be balanced for both extreme positions unless
it is apparent that only one is critical. In general, only one
center of gravity need be considered for single-place gliders.
In special cases, it may also be necessary to check the balancing
tail loads required for the loading conditions which produce
the most forward and most rearward center of gravity positions
for which approval is desired.

The following explanatory notes refer by number to items appear


ing in table 1- II :
(4) The wing loadings should be based on the design wing area.
(5) ni = limit load factor required for the condition being in
vestigated. (See Chap. 1, p. 3, "Load factors" and Chap.
e.

p.8i.)
Determine Cc
1,

(8)

(10)
(12)

as specified

in Chap.

1,

p. 8i.

The value of CM is specified in Chap. 1, p. 8i.


See also Chap. 1, p. 15, in cases involving wing flaps.

The net tail load factor n is found by a summation of mo


ments about point (2) of fig.
equation is obtained:

na=(^)

'

1-X from which

the following

Note. The above explanatory notes apply only when the force
arrangement shown In figure 1-X is used.
a different distribu
tion of external loads or a different system of measuring dis
tances is employed, the computations should be correspondingly
modified.

If

In addition to

CONTROL

SURFACE LOADS

in the beginning of this


chapter, the primary structure should meet the requirements des
cribed herein to account for the loads acting on the control surfaces.
The following loading conditions include the application of balancing
loads derived from the symmetrical flight conditions and also cover
the flight loads specified

23

the possibility of loading the control surfaces in operating the glider


and by encountering gusts.
A minimum limit factor of safety of 1 .0
and a minimum ultimate factor of safety of 1.5 should be used unless

Also,
otherwise specified.
required in certain cases.

see table

for multiplying factors of safety

Compliance Suggestion

UNIT

AND CHORD

LOADING OF SURFACES

a. The recommendations for the design of control surfaces, as out


lined above, are based on the two separate functions of control sur
The requirements also are speci
faces : balancing and maneuvering.
fied to account for the effects of gust loads.

6. The average unit loading normal to any surface is determined


from the design gliding speed V as shown by figs. 1-XIII, 1 XIVi
and 1-XVI.
When dealing with tail surfaces, it is customary to
the
value
of the average unit loading for the entire surface,
specify
The total load, which
including both the fixed and movable surfaces.
is equal to the average unit loading multiplied by the area of the
entire surface, is then distributed so as to simulate the conditions
which exist in flight. In the case of ailerons, flaps or tabs, the value
of the average unit loading is usually determined only for the partic
ular surface, without reference to the surface to which it is attached.

The average unit loading is assumed to be constant over the


Also, as shown in figs. 1-XI, and 1-XII, the unit loading at
span.
the hinge line is constant over the span.
c.

Although there are no specific chord loading conditions for


control surfaces specified above, such surfaces should be designed to
withstand a reasonable amount of chord load in either direction.
A
total chord load equal to 20 percent of the maximum normal load may
be used as a separate design condition.
The distribution along the
Tests for
span may be made proportional to the chord, if desired.
this condition are not required unless the structure is such as to
indicate the advisability of such tests.
d.

24

25

26

27

HORIZONTAL

TAIL SURFACES

Balancing. The limit load acting on the horizontal tail surfaces


should not be less than the maximum balancing load obtained from
the loading conditions specified.
The load should be distributed in
The balancing loads apply only to the
accordance with fig. 1-XI.
horizontal tail surfaces as the ailerons and the vertical tail surfaces
are used only to a small extent for balancing purposes.
The chord distribution shown in fig. 1-XI is intended to simulate
a relatively high angle of attack condition for the stabilizer in which
very high unit loadings can be obtained near the leading edge.
Loads should also be determined for the most critical center of
gravity position of the glider.

Figure 1-XI.

"Balancing"

and "damping" tail load distribution.

(Horizontal surfaces). The minimum average limit


pressure specified in table 1-I should be applied in either direction
and distributed in accordance with fig. 1-XII.
Maneuvering.

Figure 1-XII.

"Maneuvering" fail load distribution.


28

Compliance Suggestion
DETERMINATION OF MANEUVER

LOAD

The recommendations above are intended to place the determina


tion of such loads on a speed versus force-coefficient basis, to
specify values which agree substantially with current practice,
and to provide for the effects of increasing glider speeds. The
method is designed for application to conventional gliders and, in
determining the maneuver loads, the type of service for which the
glider is to be used should be considered.

The values of the average unit loading specified represents loadings


which can be attained by deflecting the control surfaces.
Higher
values may be desirable in certain cases, depending on the purpose
of the glider.

shown in fig. 1-XII represents approxi


mately the type of loading obtained with the movable surface
deflected.
For tail surfaces, this type of loading is critical for the
movable surface and for the rear portion of the fixed surface.

The chord distribution

Damping (Horizontal stabilizer). The total limit load acting on the


fixed surface (stabilizer) in the maneuvering condition should be
applied in accordance with load distribution of fig. 1-XI acting in
either direction. The load acting on the movable surface in the
maneuvering condition may be neglected in determining the damping
loads.

Compliance Suggestion
DISTRIBUTION

OF DAMPING

LOAD

When a control surface is deflected suddenly the full maneuvering


load tends to build up immediately, after which the glider begins to
acquire an angular velocity. This angular motion causes the direction

of the relative airstream over the fixed surface to change, which


causes the air load on this surface to build up in a direction such as to
This load is concentrated
oppose the angular rotation of the glider.
near the leading edge of the fixed surface and is commonly referred to

This is considered as a supplementary con


The damping
dition based on the initial maneuvering condition.
load is closely related in magnitude to the initial maneuvering
load which produces it so that it is convenient to use the latter
as the damping load.

loading condition to determine the damping load on the fixed surface.


To avoid the necessity for a separate analysis for damping loads, the
In the
distribution is made the same as for the balancing loads.
case of the horizontal surfaces, the damping load therefore acts as a
minimum limit for the design of the fixed surface and need not be
investigated when the balancing load is critical.
29

Loading for slab tail designs. The maneuvering horizontal tail


loadings shown in fig. 1-XII are applicable to all movable tail sur
face configurations including the slab tail design.

tail load distribution

with fig. 1-XII(l).

Figure

In calculating

the load should be distributed

l-XII(l).

in accordance

Balancing lead distribution, Slab Tall.

the loads for slab tail designs, the effect of tabs,

used, should be accounted for.

distributions,

For the balancing

In addition

if

to the above flight load

should be made of the ground gust


condition imposed on the slab tail. This results in a high trailing
an investigation

30

edge load similar to that induced by reverse airflow on a wing.


(See
fig. 1-XII(3.) The design airspeed should be V = 10 VW/S + 10
m.p.h.; CL = -0.8.

Figure 1XIK3). Ground guir load distribution, Slob Tail.

VERTICAL TAIL SURFACES

Maneuvering. The minimum

average

limit pressure specified in

fig. 1-XIV should be applied in either direction and distributed in


accordance with fig. 1-XII. (Above comments for horizontal sur
faces also apply, in general, here.)
Damping (Vertical surfaces). The total limit load acting on the
fixed surface (fin) in the maneuvering condition should be applied in
accordance with the load distribution of fig. 1-XI acting in either
direction.
The load acting on the movable surface in the maneuver
ing condition may be neglected in determining the damping loads.
(Above comments for horizontal surfaces also apply, in general, here.)
Gusts (Vertical surfaces). The minimum average limit pressure
should not be less than that corresponding to a 15 f.p.s. sharp-edged
gust at the design gliding speed, V. The gust should be assumed to
act normal to the plane of symmetry in either direction. For the
purpose of determining the slope of the tail lift curve, the aspect
ratio should not be taken as less than 2.0. The chord distribution
should simulate that for a symmetrical airfoil, except that the dis
tribution of fig. 1-XI may be used where applicable.

AILERONS

Maneuvering. The minimum average limit pressure specified in


fig. 1-XVI should be applied in either direction and distributed in
accordance with fig. 1-XV.
Wing flaps. Wing flaps should be loaded in accordance with the
provisions under "High-lift devices" p. 10. In any case, the average
limit prssure should not be less than 9 p.s.f . and should be considered
uniformly distributed unless a more rational distribution is used.
31
657822 O - 62 - 4

Compliance Suggestion
FLAP

DESIGN

The critical loading is usually obtained when the flap is completely


The above recommendations apply only when the flaps
extended.

are not used at speeds above a certain predetermined design speed.


is required to inform the pilot of the speed which should

A placard

not be exceeded with flaps extended.


Reference should be made to
current NACA Reports and Notes for acceptable flap data.
(See
NACA Report No. 824 and Technical Note No. 690.)

Figure 1-XV.

Aileron load distribution.

Special devices. Special design recommendations should be ob


tained in connection with the design and analysis of surfaces equipped
with unconventional ailerons, auxiliary airfoils and similar devices.
Requests for special recommendations should be accompanied by
suitable drawings or sketches of the structure in question, together
with general information and an outline of the method by which it is
proposed to determine the structural loading conditions.

Compliance Suggestion
DESIGN

OF SPOILERS

In lieu of wind tunnel data, it

is recommended that the design of


spoilers and their attachment structures be premised on the limit

loading obtained from the following formula:


Wsp = .0052 Vsp2 Where Wsv =the limit loading, p.s.f.
Vsp = the IAS at which max. operation
of the spoilers is assumed, m.p.h.
It should be assumed that the load is uniformly distributed over the
surface.

Dive brakes. The operating mechanism and supporting structure


for dive brakes should be designed for critical loads occurring in the

brakes extended flight condition, with the brake configuration


When
any position, from fully retracted to fully extended.
32

in

an

automatic brake-limiting device is employed, these parts may be


designed for critical combinations of airspeed and brake position
Brake installations should be fitted with a
permitted by the device.
"lock open" device to maintain the unit in the extreme open position.
NACA Technical Memo No. 926 contains information on dive control
brakes.
(Wing flaps may be employed as dive brake units.)

CONTROL SYSTEM LOADS

All control systems should be designed using as a basis at least the


limit forces hereinafter specified, unless a more rational method is
used.
Unless otherwise specified, a minimum limit factor of safety
of 1.0 and a minimum ultimate factor of safety of 1.5 should be used.
See also table 1- III for multiplying factors of safety required in

certain cases. See chap. 2, p. 51, "System and Components Tests"


for the operation requirements for control systems. The forces in
the control system members, cables or push rods operating the mov
able surfaces should be computed and their effect on the rest of the
structure should be investigated and allowed for in the design of
such structure.

Compliance Suggestion

DETERMINATION OF LOADINGS
The control forces recommended are of an arbitrary nature; hence
In
they may prove to be somewhat irrational in certain cases.
general, however, they represent simplified requirements which will
If he so desires, the designer
result in satisfactory control systems.
may use a more rational loading for the design of the control system.
The following loadings are considered satisfactory. The control
systems may be designed for limit loads 25 percent greater than those
corresponding to the limit loads specified for the controlft surfaces to
which they are attached, assuming the movable surfaces to be in
that position which produces the greatest load in the control system
except that the loads should not be less than those listed below:
(a) Elevator: 75 lb. fore-and-aft
(6) Rudder: 100 lb. on one pedal only and
200 lb. on each pedal simultaneously
(c) Aileron: 50 lb. laterally or as part of a couple applied to the
control wheel
The control forces specified should be applied to the entire control
system, including the control surface horns. The multiplying factor
of safety of 1.15 need not be applied to the fittings in the control
system.

In applying

the recommendations for elevator


systems, a control force of 150 pounds should be assumed to act in
a fore-and-aft direction and should be applied at the grip of the
control stick, or should be equally divided between two diametrically
opposite points on the rim of the control wheel.

Elevator

systems.

33

Rudder

systems.

In applying the recommendations for rudder

systems, a control force of 150 pounds should be assumed to act in


a direction which will produce the greatest load in the control system

and should be applied at the point of contact of the pilot's feet with
As a separate condition, two forces of 200 pounds
magnitude should be assumed to act simultaneously at both points
of contact of the pilot's feet with the control pedal.
the control pedal.

systems. In applying the recommendations for control


loads, it should be assumed that the ailerons are loaded in

Aileron
system

opposite directions. A control force of 60 pounds should be assumed


to act as part of a couple equal to the specified force multiplied by
Suitable assumptions should be
the diameter of the control wheel.
made as to the distribution of the control force between the ailerons.

In regard to

distribution of the control force between


ailerons, the following assumptions are considered suitable:

the

the

For nondifferential ailerons,

75 percent of the stick force or


couple should be assumed to be resisted by a down aileron, the
remainder by the other aileron; also, as a separate condition,
50 percent should be assumed to be resisted by an up aileron,
the remainder by the other aileron.

For differential

percent of the stick force or


by each aileron in
either the up or down position, or rational assumptions based
on the geometry of the system should be made.
ailerons,

couple should be assumed

75

to be resisted

Flap and auxiliary control systems. In applying the recommenda

tions for control system loads, suitable minimum manual forces


should be assumed to act on flap control systems and other similar
controls.

Compliance Suggestion
MINIMUM LIMIT FORCES

It

is recommended that the following limit forces be used as mini


mum values for the design of flap and auxiliary control systems:
(1)

It

Flaps

50

(2) Spoilers
(3) Hand operated brakes
(4) Foot operated brakes

50
75
100

lb.*
lb.*
lb.*
lb.*

should be noted that the flap position that is most critical for
the flap proper may not be critical for the flap control mechanism
and supporting structure.
In doubtful cases the flap hinge moment
can be plotted as a function of flap angle for various angles of attack
The necessary characteristic curves should
within the design range.
be obtained from reliable wind tunnel tests.
The force used for the design of flap and spoiler control systems should not be less than
times the force corresponding to the limit load used for the design of the surfaces.

1.25

34

Towing and launching {release mechanism) control systems. In


applying the recommendations for control system loads, a control
force of 75 pounds should be assumed to act in a direction corres
ponding to that normally used by the pilot, and should be applied at
the grip of the control handle or lever.
To aid in assuring emergency release it is recommended that a
suitable placard or painted instruction be placed adjacent to the
glider release hook to indicate that tow rope size (strength) in excess
of the limit load of the release mechanism should not be used.
Also, for auto or winch towing, provisions should be made for a
back load trip release mechanism to preclude any possibility of
failure to release the towline.

GROUND LOADS

The following conditions represent the minimum amount of investi


gation recommended for conventional landing gear. For unconven
tional types, it may be advisable to investigate other landing attitudes,

depending on the arrangement and design of the landing gear mem


Consideration will be given to a reduction of the specified
limit load factors when it can be proven that the shock absorbing
system will positively limit the acceleration factor to a definite
lower value. A minimum limit factor of safety of 1.0 and a minimum
ultimate factor of safety of 1.5 should be used unless otherwise
Also, see table l-III, for multiplying factors of safety
specified.
required in certain cases.
bers.

Compliance Suggestion

CONVENTIONAL

LANDING GEARS

Insofar as the requirements of ground loads are concerned,


landing gears will be considered conventional if they consist of:

single wheel or double coaxial wheels located on the bottom


of the fuselage and directly below (or nearly so) the center of

gravity of the glider, together with auxiliary skids attached to


the bottom of the fuselage.
One auxiliary skid running from
the wheel forward to the nose, the other running aft to a point
The rear
below the wing trailing edge (approximately).
a
suitable
skid
be
or
auxiliary
replaced
supplemented by
may
tail skid (see fig. 1-XVII), or

single main skid on the bottom of the fuselage which extends


from the nose to a point below the wing trailing edge (approxi
This skid may be supplemented by a tail skid.
mately).
Note.

Wing tip

skids may be employed

if

desired.

Level landing. The glider should be assumed to make contact with


the ground while in a level attitude.
The basic vertical component
35

should be equal to the gross weight of the glider.


additional assumptions should be made:

The following

For wheel type landing gears, the minimum vertical limit

load factor should be 4.0. The resultant ground reaction


should pass through the center of the axle and should be
obtained by combining the vertical component with a rear
ward acting horizontal component equal to one-quarter of the
vertical component.
For skid type landing gears, the minimum vertical limit load
factor should be 5.0. The resultant ground reaction should
pass through the center of the skid's contact area, and should
be obtained by combining the vertical component with a
rearward acting horizontal component equal to one-half of
the vertical component.

Compliance Suggestion
DETERMINATION OF LOADING

The loading for this condition is illustrated in fig. 1-XVII. As it is


difficult to accurately define "level altitude," any approximately
level altitude with the tail well off the ground will be considered
satisfactory. If in the level landing condition the resultant load
does not pass through the center of gravity, it will generally be accept
able to apply a balancing couple composed of an upward force acting
near the nose of the fuselage and an equal downward force acting at
the same distance to the rear of the center of gravity.
These arbitrary
forces can be considered as approximately representing angular inertia
forces and may be divided between the nearest panel points, if desired.
These forces are illustrated in fig. 1-XVII (a) .
Level landing with side load. As a separate condition, a limit side
load equal to 0.167 times the limit vertical component should be
assumed to act at the center of the contact area of the tire or skid,
The side
together with the loads specified under "level landing."
load should be assumed to act in either direction normal to the plane
of symmetry.

Compliance Suggestion

DETERMINATION OF LOADING

The loading for this condition is shown in fig. 1-XVIII.


An
acceptable method of balancing externally applied rolling moments
about the longitudinal axis resulting from the side load is also shown
in fig. 1-XVIII (a). Forces resisting angular acceleration
are
The arbitrary location shown is
assumed to be applied by the wing.
based on the fact that the effectiveness of any item is proportional to
Balancing loads may be
its distance from the center of gravity.
assumed to be vertical, although they actually act normal to a radius
line through the center of gravity of the glider.
36

Nose-down landing. For this landing


assumptions should be made :

For Wheel

( a )

( b )

condition,

the

following

Type Landing Gears

For Skid Type Longing Gears

Figure 1XVII. Level landing.

For wheel type landing gears, the glider should be assumed to

make contact on the nose skid or wheel and the main wheel or
wheels.
The minimum limit resultant inertia force should act
at the center of gravity of the glider, should be equal to 4.0
times the weight, and should act forward and downward at an
The direction of ground
angle of 14 degrees with the vertical.
reactions at the contact points should be opposite to the
resultant inertia force.
37

For skid type landing gears, the glider should be assumed to be


nosed down 15 degrees.
The minimum limit, vertical com

ponent of the ground reaction should be equal to 5.0 times the


weight. The resultant ground reaction should pass through
the most forward point suitable for the application of oblique
loads, and should be obtained by combining the vertical com
ponent with a horizontal component equal to one-half of the
vertical component.

Note. These conditions are illustrated in figure 1-XIX.

C.G

1 .

HOR.

NOTE:

Pv=4w(LlMIT)
Ps=O.I67 Pv=0.67w(LIMlT)
P|=Pv2

(a)

HOP

NOTE:

PR'
(b)

PS2(LIMIT)

For Wheel Type Landing Gears

)
'ml

Pv =5w(LIMIT)

-1

PS=0.I67Pv =0.84w(LIMIT)

p|=Pv2+P| (LIMIT)

For Skid Type Landing Gears

Figure 1XVIII.

Level landing with tide lead.

Head-on landing. The forward portion of the fuselage should be


capable of resisting an ultimate load of 6.0 times the gross weight of
the glider acting aft through the foremost point(s) suitable for the
application of such a load. Partial failure of the structure under
38

these conditions is tenable provided that the specified

ultimate load

can be resisted without endangering the occupants, assuming safety


belts to be fastened.
(Also Chap. 3, p. 115.)
(Note the 6.0 factor
above is ultimate and not a limit load factor.)
Wing-tip landing. Suitable provisions should be made to provide
adequate structure to resist possible severe ground reactions at the
wing tips.

( a )

For Wheel

( b )

For

Figure 1XIX.

Type Landing Gears

Skid Type Landing Gears


Nose-down

39

landing.

Compliance Suggestion

It

LOADING CONDITIONS

may be assumed that a limit load of 150 pounds acts aft at the
point of contact of one wing tip, or wing skid, and the ground in a
direction parallel to the longitudinal axis. The unbalanced turning
moment may be assumed to be resisted by:
The methods shown in fig. 1-XX, or
The angular inertia of the glider.

ON TAIL SKID

(MOST FORWARD POINT


SUITABLE FOR THE APPLI
CATION OF SUCH A LOAD P)

NOTE:

37.5 b

Figure 1-XX. Wing tip landing.

LAUNCHING AND TOWING LOADS

The towing and launching fittings (and/or mechanisms) and that


portion of the structure ahead of the main wing fittings should be
checked as recommended below.
Holding fittings and the structures
40

to which they are attached also should be investigated for pertinent


loads. A minimum limit factor of safety of 1.0 and a minimum
ultimate factor of safety of 1.5 should be used unless otherwise speci
Also,

fied.

see

cases.

table 1-

III

for factors of safety required in certain

Loads on fittings. A limit load of 900 pounds or 2.0 times the gross
weight, whichever is greater, should be assumed to act in the following
separate cases :

Forward at the towing and launching fitting (or mechanism),

and aft at the rear holding fitting.

At

the towing and launching fitting and directed forward and


upward at the maximum angle which will afford adequate

it need not exceed an angle


with
of 30 degrees
the longitudinal axis.
At the towing and launching fitting, and directed forward and
downward at an angle of 75 degrees with the longitudinal axis.
At the towing and launching fitting, and directed forward and
sideward at an angle of 30 degrees with the longitudinal axis.
clearance with the glider; however,

The above loadings are shown in fig. 1-XXI. The effects of these
loads need not be investigated aft of the front wing spar.
Wing truss strength. Unless the strength of the wing in resisting
rearward acting chord loads is equal to or greater than the strength
in resisting forward acting chord loads, provisions should be made to
provide adequate strength of wing drag trusses to resist chord inertia
loads developed in glider launching and towing.

Compliance Suggestion
LOAD

It

can be assumed that a

FACTOR

limit rearward acting chord load factor of

3.0 is developed in shock cord/winch launches.

In addition

MULTIPLYING

FACTORS OF SAFETY

factors of safety specified for each


loading condition, the multiplying factors specified in table 1and the following paragraphs should be incorporated in the structure.
The total factor of safety required for any structural component or

part equals
in question
except that
indicated in

to the minimum

the minimum factor of safety for the loading condition

multiplied by the factors of safety hereinafter specified,


certain multiplying factors may be included in others, as
table 1-III. The use of a fitting factor is not considered

in cases wherein certain special factors are used, such


those covered by items la, 2, 6, 7 and 8 of table 1- III.

necessary

III

as

RELEASE MECH. OR
LAUNCHING HOOK

HOLDING FITTING FOR


SHOCK CORD LAUNCHING

(a)

Fittings. All fittings in the primary structure should incoporate


the multiplying factor of safety specified in table 1- III. For this
purpose, fittings are defined as parts used to connect one primary
member to another and should include the bearing of these parts on
the members thus connected.
Continuous joints in metal plating
and welded joints between primary structural members are not classi
fied as fittings.
(See Chap. 3.)

All
castings in the primary structure should incorporate
Castings.
a multiplying factor of safety not less than that specified in table

i-in.

Parallel double wires. When parallel double wires are used in wing

lift

trusses, each wire should incorporate a multiplying factor of


safety as specified in table 1- III.
Wires at small angles. Wire or tie-rod members of wing or tail
surface external bracing should incorporate a multiplying factor of
safety as follows:

L/2R

(except that

K =the
R

K shall

additional factor

not be less than 1.0), where

the reaction resisted by the wire in a direction normal to

the wing or tail surface plane, and

the load required in the wire to balance reaction R.


Table

l-III

Additional (Multiplying) Factors of Safety


Additional ultimate May be covered by
[actor of safety, ].
Item No.

Item

1.

1.15 la, 2, 4, 5,6, 7,

Fitting (except control system fittings).

la. Fittings at joints where nontapered pins or


bolts are removed during routine dis
2.

3.
4.
5.
6.
7.

8.
9.
10.

mantling
Castings
Parallel double wires in wing lift truss
Wires at small angles
Double drag truss wires
Torque tubes used as hinges
Control surface hinges 1
Control system joints 1
Wire sizes
Wing lift truss (when affected by landing
loads)

2.00

8,9

2.00
2.00
1.05

See p. 43
See p. 43

1.5
6.67
3.33

See p. 44

1 For bearing stresses only.


* Includes non-tapered pins and bolts which are removed during routine

1.20
dismantling.

Double drag trusses. Whenever double drag trussing is employed,

all drag wires should incorporate a multiplying factor of safety varying


linearly from 3.0, when the ratio of overhang to root chord of overhang

is 2.0 or greater, to 1.20 when such ratio is 1.0 or less, assuming an


equal division of drag load between the two systems.
43

Torques tubes used as hinges. When steel torques tubes are em

ployed in direct bearing against strap-type hinges they should incor


porate a multiplying factor of safety at the hinge point not less than
that specified in table 1-III. (Also, see Chap. 3.)

Control surface
surface hinges and control system joints.
hinges and control system joints subjected to angular motion, except
ing ball and roller bearings and AN standard parts used in cable
Control

control systems, should incorporate multiplying factors of safety not


less than those specified in table 1with respect to the ultimate
bearing strength of the softest material used for a bearing. For ball
or roller bearings a yield factor of safety of 1.0 with respect to the
manufacturer's non-Brinell rating is considered sufficient to provide
an adequate ultimate factor of safety.
Wire sizes. (See Chap. 3.)
Wing lift trusses. Lift wires should be in duplicate and when
landing loads are carried through a portion of the lift truss the lift
truss members so affected should incorporate a multiplying factor of
safety not less than that specified in table 1 III.

III

44

Chapter

2 PROOF OF STRUCTURE

Proof of compliance with the loading recommendations suggested in

consists of structural analyses, load tests, flight tests, refer


ences to previously approved structures, or combinations of the above.

Chapter

Any condition shown to be noncritical need not be further investi

Also, the glider applicant is free to develop and present any


gated.
method he chooses for showing compliance with the specified recom
mendations.

DETERMINATION

OF LOADINGS

CONTROL SYSTEMS

Flight controls. The minimum loads to be used for the design of


flight control systems are covered on pp. 33, 34.
Secondary controls. The minimum loads to be used for the design
of secondary control systems are covered on pp. 34, 35.

FUSELAGES

Weight

distribution. All major items of weight affecting the

should be distributed to
center of gravity of the
suitable vertical division
rules should be followed
ventional gliders.

The weight of an item located between two adjacent panel

points of the side trusses should be divided between those


panel points in inverse porportion to the distance from them
to the center of gravity of the item.
The weight of an item supported at three or more panel
points should be divided between those points by the aid of an
investigation and analysis of the method of support, if practi
cable.
Otherwise, a conservative distribution should be
assumed.

fuselage

convenient panel points so that the original


A
fuselage and its contents is maintained.
of loads should be included. The following
in computing the panel point loads for con

In all cases the moment of the partial panel loads due to any
item about an origin near the nose of the fuselage should be
equal to the moment of the item about that origin.
All loads may be assumed to lie in the plane of symmetry
and to be divided equally between the two vertical fuselage
trusses.

45

STRUCTURAL ANALYSIS AS CRITERIA OF STRENGTH


Structural analyses are considered criteria of complete proof of
strength only in the case of structural arrangements for which ex

perience has shown such analyses to be reliable. References should


be shown for all methods of analyses, formulas, theories and material
In some
properties which are not generally accepted as standard.

the acceptability of a structural analysis may depend


indicated excess strength incorporated in the structure.
cases

on the

Mechanical properties of materials. The structural analysis should


be based on the guaranteed minimum mechanical properties of the
materials specified on the drawings, except in cases where exact
mechanical properties of the materials used are determined.
The
effects of welding, brazing, form factors, stress concentrations, dis
continuities, cutouts, instability, redundancies, secondary bending,
joint slippage of wood beams, rigging, end fixity of columns, eccen
tricities, air loads on struts, and vibration shall be properly accounted
for when such factors are present to such an extent as to influence
the strength of the structure.

Compliance Suggestion

COMPUTING

OF LOADS AND

STRESSES

Acceptable methods for computing the allowable loads and stresses


corresponding to the minimum mechanical properties of various
materials are given in Bulletin ANC-5 "Strength of Metal Aircraft
Elements," obtainable from the Superintendent of Documents,
Washington, D. C.

PROOF OF WINGS
For proof of wings by structural analysis only,
Analysis as Criteria of Strength," p. 46.
Compliance Suggestion

see

"Structural

The following points should be considered in the wing analysis :


Joint slippage. When a joint in a wood beam is designed to
transmit bending from one section of the beam to another or
to the fuselage, the stresses in each part of the structure should
be calculated on the assumption that the joint is 100 percent
efficient and also under the assumption that the bending
moment transmitted by the joint is 75 percent of that obtained
under the assumption of perfect continuity.
Each part of
the structure should be designed to carry the most severe loads
determined from the above assumptions.
Bolt holes. In computing the area moment of inertia, et cetera,
of wood beams pierced by bolts, the diameter of the bolt hole
should be assumed to be 1/16-inch greater than the diameter of
the bolt.
46

Box beams. In computing the ability of box beams to resist


bending loads only that portion of the web with its grain parallel
to the beam axis and one-half of that portion of the web with its
grain at an angle of 45, to the beam, should be considered.
The more conservative method of neglecting the web entirely
maybe employed.
Drag trusses. Drag struts should be assumed to have an end
fixity, with a coefficient of 1.0, except in cases of unusually
rigid restraint, in which a coefficient of 1.5 may be used.

PROOF OF CONTROL

SURFACES

Suitable structural analyses of control surfaces will be accepted as


complete proof of compliance with the ultimate load requirements pro
vided that the surfaces are of conventional construction. However,
proof tests are required to prove compliance with yield requirements.
Inasmuch as many control surfaces do not lend themselves to rigorous
analysis, it is recommended that strength tests be considered for
proving compliance with the ultimate load requirements. The
analysis and tests should include the horns, and should demonstrate
compliance with multiplying factors of safety requirements con
tained in table 1- III.

Compliance Suggestion

In

DEFLECTION

OF HINGE POINTS

analyzing movable control surfaces supported at several hinge


points, care should be taken in the use of the "three moment" equa
In general, the assumption that the points of support lie in a
tions.
straight line will give misleading results.
When possible, the effects
of the deflection of the points of support should be approximated in
the analysis.

Compliance Suggestion
RIGGING LOADS

The effects of initial rigging loads on the final internal loads are
difficult to predict, but in certain cases may be serious enough to
warrant some investigation. Methods based on least work or deflec
tion theory offer the only "exact" solution. Approximate methods,

however, are satisfactory if based on rational or conservative over


lapping assumptions.

PROOF OF CONTROL

SYSTEMS

Structural analyses of control systems will be accepted as complete

proof of compliance with ultimate load requirements when the struc


ture conforms with conventional types for which reliable analytical
methods are available. Proof tests, however, are required to prove
compliance with yield load requirements.
47
657822 O - 62 - 5

Analysis or individual load tests should be conducted to demon


strate compliance with the multiplying factor of safety requirements
specified in Chap. 1 pertaining to control system joints subjected to
angular motion.
In addition to the proof tests and analyses, operation tests are also
required.

Compliance Suggestion
CRITICAL

LOADINGS

In some cases involving special leverage or gear arrangements, the


critical loading on the control system may not occur when the surface
is fully deflected.
For example, in the case of wing flaps, the most
critical load on the control system may be that corresponding to a
relatively small flap displacement even after proper allowance is
made for the change in hinge moment. This condition will occur
when the mechanical advantage of the system becomes small at small
The proof of control systems should include the
flap deflections.
most severe loading conditions for all parts of the system.
An investigation of the strength of a control system includes that
of the various fittings and brackets used for support. In particular,
the rigidity of the supporting structure is important especially in
ailerons, wing flap, and tab control systems.
PROOF OF LANDING GEARS
Structural analyses of landing gears will be accepted

as complete

proof of compliance with the load requirements when the structure


conforms with conventional types for which reliable analytical meth
ods are available.
For gliders, equipped with an auxiliary powerplant and conventional airplane type arrangement of main and tail
or main and nose wheels, compliance should be shown with the land
ing gear requirements of Civil Air Regulations Part 3.

Compliance Suggestion
WHEELS

AND TIRES

For wheel type landing gears, the approved wheel rating shall equal
or exceed the gross weight, if one main landing wheel is used, or
shall be half the gross weight if two main landing wheels are used.
When unrated wheels are employed, their ultimate strengths should
not be less than the ultimate loads to which they are subjected. Any
standard tire adaptable to the wheel will be considered acceptable.

SHOCK ABSORPTION
There are no definite recommendations regarding the energy
absorption characteristics of glider landing gears. On heavy gliders
either air wheels or shock absorbing skids should be used.
48

PROOF OF FUSELAGES

Proof of fuselages by structural analysis only should be in accord


ance with procedures described above.
PROOF OF FITTINGS AND PARTS
Compliance Suggestion
In the analysis of a fitting it is advisable to tabulate all the forces
which act on it for the various design conditions. This procedure will

reduce the chances of overlooking some combination of loads which


may be critical.
The additional ultimate factor of safety of 1.15 for fittings (table
1is to account for various factors such as stress concentrations,
eccentricity and uneven load distribution, which tend to decrease the
strength of the fitting.

III)

In

COMBINED STRUCTURAL ANALYSIS AND TESTS

certain cases it may be advisable to combine structural analysis


procedure with the results of load tests of portions of the structure
not subjected to accurate analysis.

Compliance Suggestion

Generally, structural analyses are considered satisfactory for show


ing compliance of conventional type structures with the ultimate
load requirements. However, certain 'limit load tests and operation
tests should be conducted in accordance with the procedures outlined
below. For unconventional type structures for which reliable stress
analysis methods have not yet been developed, it is usually necessary
to resort to combined analysis and limit load tests, or ultimate load
tests alone, to show compliance with the ultimate load requirements.
D-nose wing spars, fuselages, and wings of sheet-stringer construc
tion and structures which may be adversely affected by such factors
as cutouts and discontinuities, covering behavior including wrinkling,
shifting of neutral plane, changes in stress distribution, et cetera, are
considered as unconventional structures because they cannot be sub
stantiated by analysis methods alone.
Prior to deciding whether combined analysis and limit load tests or
ultimate tests alone are most practicable, it is recommended that
an investigation of the effort and cost involved be conducted. The
following points should be considered:
1.

Components which have been tested to their ultimate strengths


should not be in certificated gliders unless it can be shown that
no damage including detrimental permanent set has occurred
in any part of the structure or that such damage has been
properly repaired.
49

2.

3.

4.

Test results should be reduced to correspond to the minimum


mechanical properties of the materials used (which requires
additional tests).
In certain cases, the cost of preparing structural analyses may be
appreciably less than the cost of strength tests. This is especi
ally true when extra aircraft components, test jigs, et cetera,
must be constructed for test purposes and there are only a
relatively small number of gliders involved.
In certain cases, components of the gliders may be built suffi
ciently overstrength without excessive weight penalty, so that
tests of the particular component may be conducted without
When ultimate load tests are
causing failure or permanent set.
conducted, the stress analysis need include only the determina
tion of the external loads onto the structure or component.
Detailed stress analyses need not be prepared except for fittings.
However, if the strengths of the fittings are demonstrated by
static tests, the test loads should be equal in magnitude to the
fitting design load. Material variation factors need not be used
in fitting tests.

LOAD TESTS
Demonstration of compliance with structural loading recommenda
tions by means of load tests only is permissible provided that ultimate
and limit tests are conducted to demonstrate compliance.

Compliance Suggestion
STATIC

TESTING

In static testing of structural components,

no material correction

factor is required. However, care should be taken to see that the


strength of the component tested conservatively represents the
strength of subsequent similar components to be used on gliders to be
Included in the test report should be a
presented for certification.
statement certifying to this fact.

If load

SPECIAL TESTS

tests do not show compliance with the particular multiplying


factor of safety recommendations, the tests should be supplemented

by special tests or analyses


mendations.

to prove compliance with such recom

SYSTEM AND COMPONENT TESTS

Wing ribs. The strength of ribs should be demonstrated by static


tests to at least 125 percent of the ultimate loads for the critical load
ing conditions.
Control surfaces. Static tests of the control surfaces to limit loads
should be conducted.
50

Control systems. Static tests of the control systems to their limit


loads should be conducted. Also, operating tests of the control
systems loaded to 80 percent of their limit load values specified in
Chap. 1 should be conducted to show that the control systems will
operate properly when subjected to loads which simulate flight con

ditions.

towing release mechanisms. Static tests of the


and towing release mechanisms to their limit loads should

Launching

launching

and

be conducted.
be conducted

Also, operation tests of release mechanisms should


to show they will function properly when loaded
throughout the range from zero to 100 percent of the limit force values
These operational
specified in Chap. 1 for release mechanisms.
tests should include the back load trip release mechanism, if installed.
Hardware used in towlines should be of sufficient rigidity to avoid
distortion and possible malfunctioning or breakage after repeated
use.
The above recommendations concerning operation tests do not
apply to "open-hook" launching fittings used solely for shockcord
type launching apparatus. The strength of the control system
actuating the release mechanism is covered in Chap. 1 .

Compliance Suggestion
TEST

PROCEDURE

These operation tests should be conducted with the fuselage sup


ported and restrained in a manner which will avoid any excessive
"springing" of the fuselage nose sections when the test load is suddenly
released. Inasmuch as the purpose of the test is to demonstrate the
releasing characteristics of the mechanism under load, the fuselage
resisting loads may be applied at any convenient points on the fuselage
near the release mechanism location.
TEST LOADS, APPARATUS

AND METHODS

The determination of test loads, the apparatus used and the methods

of conducting the tests should be brought to the attention of the


regional office concerned prior to conduct of the tests.

Compliance Suggestion
ULTIMATE

LOAD AND DESTRUCTION

TESTS

An ultimate load test is used to determine the ability of the struc


ture to withstand its ultimate design load. For conventional type
structures, the stress analysis determines this satisfactorily but if the
structure is of an unconventional type, an analysis cannot be relied on.
In other cases, the manufacturer may not wish to submit a complete
stress analysis. Ultimate load tests are, therefore, recommended in
such cases as an available method for determining whether the struc
ture will fail before it reaches the required ultimate load.
51

When a static load test is carried to the point where the maximum
carrying capacity of the structure is reached, the test is usually
referred to as a destruction test. An ultimate load test is not neces
sarily a destruction test.

In cases wherein the strengths of structures are demonstrated by


ultimate load tests in lieu of stress analyses, the proposed test pro
gram should be submitted for verification before the tests are con
ducted. Particular items which should be given special consideration
in an ultimate load test are (1) the testing of all members, or portions
of the structure requiring excess factors of safety and (2) taking into
account the question of material variations from standard specifica
tions and possible discrepancies
between the test specimen and
drawings.
Compliance Suggestion
MATERIAL

TESTS

Standard properties. Drawings which are to be used as a basis for


a type certificate will specify certain minimum guaranteed material
properties, usually by reference to existing standard specifications.
It is not necessary that the glider applicant substantiate the strength
characteristics of standard materials if the purchasing invoices show
they are in accordance with standard specifications. In cases where
new or unconventional materials are used, special strength tests should
be conducted to establish guaranteed minimum properties suitable
for design.

Stress-strain diagrams. In general, the most useful data are ob


tained from a stress-strain diagram obtained in a tension test and
such diagrams should be obtained in all cases where new materials are
used.
This diagram permits the determination of the following
important characteristics :
1.

2.

Further information

3.

Ultimate tensile stress


Yield point in tension
Modulus of elasticity (E)

properties of materials, stressstrain diagrams, et cetera, can be obtained from ANC-5, materials
textbooks, et cetera.
Special materials

on

strength

tests. In

many cases, special tests should be


conducted to account for factors difficult to evaluate in a stress
analysis. The effects of welding after heat treatment are difficult to
predict in some cases. Stress-concentration caused by poor detail

will often reduce the allowable stresses considerably below


standard values.
Most metals show marked reductions in allowable
design

after being subjected to repetitive loadings even in cases


wherein the stresses are relatively low.

stresses

52

It

METHODS OF CORRECTING

TO STANDARD

is necessary to know the type of failure which is critical in order

that proper correction factors may be used to reduce the results to


For a "built-up" structure, failure can occur in many
standard.
In general, it is only necessary
different ways and at different places.
to derive correction factors for the particular portion and for the

particular mode of failure which occurred. When the total load


sustained is 15 percent greater than the "ultimate" load required, no

When the strengths


additional material corrections are necessary.
of fittings are demonstrated by ultimate load tests, material correc
tion factors are not considered necessary since the fitting design factor
of 1.15 is believed sufficient to cover it.
The material correction factor should be made by multiplying the
test load sustained at failure by the ratio of standard strength of the
material to the strength of a specimen taken from the structure.
The particular strength property involved will depend largely on the
mode of failure. In general, it is desirable to obtain a stress-strain
A chemical analysis might be
diagram for the material specimen.
advisable if there is doubt as to the actual material used in the test
structure.

Jigs. Tests of tail

TEST PROCEDURES

it

it

is

is

is,

surfaces, wings and similar components are


usually conducted by mounting the surface to be tested onto a speci
ally built jig or framework, using the regular attachment fittings of
the unit being tested.
The jig should conform to the glider structure
as far as possible.
In cases where the attachment of a component
to the fuselage involves the distribution of concentrated loads into a
thin-walled structure, it is highly desirable to test the surfaces while
attached to the actual structure or to the portion affected ; otherwise
the strength and rigidity of the jig will be imparted to the test thereby
leading to erroneous conclusions of excess strength. Special care
should be taken to obtain net deflections of the surface tested; that
the deflections of the jig should be deducted from the total deflection.
Loading schedule. loading schedule should be prepared. The
schedule shows the load distribution to be used and the values of the
loads to be applied at each stage of the loading process. When the load
to be applied by means of bags of shot or by weights,
usually
to
each
increment
of
in
advance
and
to
expedient
loading
weigh
assign
to marked space on the floor, so that no confusion will result.
The
loads can be divided into suitable increments of about one-sixth
(16.7 percent) of the ultimate load. In the usual case, such incre
ments will be one-fourth (25 percent) of the required "limit" load, so
that the limit value of test load will have been reached at the fourth
increment. The ultimate value of test load will then be reached at
the sixth increment.
After reaching the ultimate load, the size of
53

in
crement will produce H5 percent of the "ultimate" load. However,
if the structure should show signs of failing at any time, the loading
increments should be accordingly reduced so that the test loads will
exceed the failing load by as small a margin as possible.
Supports It is advisable to support the unit being tested by means
of jacks during the load application.
A safety framework or blocking
should be provided in all cases so that the structure will not deflect
too much after failure. This not only protects workmen and observ
ers but also permits an accurate determination of the point of initial
failure and may permit continuation of the test after local reinforce
ment if such is desirable.
Deflection sticks should be attached at
various points of the test specimen and a level should be provided for
reading the scales, which should preferably be graduated in tenths of
an inch. See figs. 2-I and 2-II.
Special procedure in limit load tests. At the start of the test, it is
advisable to apply at least a part of one increment and remove it
before measuring the initial positions of the deflection stations.
After each load increment is applied, the jacks should be lowered for
a period of at least 1 minute before deflection readings are taken.
When the total "limit" load has been loaded onto the structure and
readings have been obtained, the entire load should be removed,
The deflection readings at zero
preferably one increment at a time.
load should then be obtained.
Special procedure in ultimate load tests. The procedure outlined for
the limit load test described in the preceding paragraph should be
followed until the limit load test is completed.
It will be noted that
the ultimate load test, if conducted first, would not permit the deter
mination of the permanent set caused by the "limit" load. After
the limit load test, the loading should be continued beyond the limit
As the ultimate
load value in accordance with the loading schedule.
load is approached, the structure should be carefully observed and any
unusual behavior noted.
The increments should be reduced if any
If the structure should fail locally be
signs of failure are observed.
fore reaching ultimate, it is permissible to reinforce the failed portion.
When that is practicable, the test should then be resumed.
The
details of reinforcement should be carefully noted.
If the material
correction factors will be small, it is not necessary to proceed to the
H5 percent overload. If the test specimen cannot be used after
test, it is desirable to continue the test to destruction, that is; through
When failure begins during the lowering of the
to complete failure.
jacks, it is advisable to remove some of the load before completely
removing the support, in order that the minimum load causing failure
can be determined as closely as possible.
Special procedures when ultimate load tests are conducted in lieu of
stress analysis. In such cases the procedure is the same as for ulti
the increments should be reduced

so that the second additional

54

mate

load tests except that it will often be necessary to prove that


specified extra loads (higher factors of safety) can be carried by cer

tain

also

portions of the structure.

graphs

and

of
as

Additional design conditions may


Whenever possible, adequate photo
should be taken and samples of the material should be obtained

have to be investigated.

tested.

conformity check is made


Check of test structure. In most
the test specimen against the drawings and other design data used
a basis for certification.

z^

In the case of ultimate load tests in lieu of stress analysis, a particu


larly thorough conformity check is made. After the test, the portions
that failed usually are further checked for dimensions and strength
properties.

TYPICAL SECTION THROUGH WING


2/3

approx.

^Xmetal

OR WOOD
EXTENSION PIECE

>SV

'

1/3 c
approx .

Attached by CLIPS screwed or


1rivetted to the major structure
of the wing.

SUSPENDED
Figure 2I.

SCALE

Chordwise extension piece to magnify wing torsional deflect/on readings.

TEST REPORT

In all

cases the manufacturer making a test is required to submit


a complete report covering details of tests. The report should include

photographs or drawings of the test setup and the test specimen;


photographs of failed parts or sections; records of deflections and
readings taken; date of test; identification number of report; serial
and model number of glider and signature of responsible witnesses
In addition, the following points should be
and/or test personnel.
when
covered
applicable:

Substantiation by references or computations of the selection


of critical test conditions and loadings.
Loading schedule used in the test.

Description of test setup, with reference to drawing numbers.


Chronological account of the test procedure and events.

Deflection

deflections.

readings,

preferably

Disposition of tested structure.


55

in tabular

form.

Also jig

S3QinO

unBy

/diuoxj

jo *tn to .,0ul

uofpyp

Ol

IHOddflS

pjooq

WV38

1SNIV9V

WING TESTS
Rib

tests.

A. Selection of ribs.
1.

2.

3.

4.

Wing of uniform chord. At least two ribs should be tested


for each of the two loading conditions.
Tapered wing. Considerable judgment should be used.
Where a series of ribs of varying sizes is involved, the largest
rib of each series should be selected for testing.
Where tapered wings incorporate either two or three similar
series of ribs, if two series are used, the tests should be made
on two each of the largest rib in each series, or a total of four
ribs. If there are three series, it would probably be sufficient
to test two identical ribs of the largest size used and one each
of the largest, in each of the other series.
Usually, no more than a total of four ribs need be tested.
However, in all cases, it is essential that representative ribs
be tested.

B. Test loadings.
1.

2.

The rib tests should at least cover the positive high angle of
attack condition (Condition I) and a medium angle of attack
condition. The total load to be carried by each rib should
equal 125 percent of the ultimate air load over the area sup
ported by the rib. For the medium angle of attack condi
tion, the load factor should be taken as the average of the
ultimate load factor for Conditions I and III.
The leading edge portion of the rib may be very severely
loaded in Conditions
and IV. An investigation of the maxi
mum down loads on this portion should be made when V
exceeds 125 m.p.h.
If this is not applicable, it should be
demonstrated that the rib structure ahead of the front spar
is strong enough to withstand its portion of the test load
acting in the reverse direction. A test for this condition
usually is advisable in the case of a rib which appears to be

II

weak.

3.

The following loadings are recommended for two-spar wing


construction when the rib forms a complete truss between
the leading and trailing edges.
a. For the high angle of attack flight condition, ribs of
chord length greater than 60 inches should be subjected
to 16 equal loads at the load points given in tables 2-IV
or 2-V. In order to determine which set of load points
is applicable to the particular airfoil used, it is first neces
sary to determine the following airfoil characteristics:
classification this is
(1) PD
(Pressure Distribution)
expressed by a capital letter followed by a two digit
57

For the
cetera.
present purpose, only the number portion of the classi
fication need be considered.

about the aerodynamic


(2) Cmttc moment coefficient
number such

as

10,

11,

12, et

center.

(This is necessary only


(3) Camber in percent chord.
in the case of airfoils having a 12 pressure distribution

b.

classification.)
These characteristics are readily obtainable for most air
Technical Reports Nos. 610 and
foils from N.A.C.A.
For airfoils in the 10 or 11 classification, the load
628.
points should be taken from table 2-IV, using the fine
corresponding to the Cmtte value of the airfoil.
(Table
2-IV should also be used for ribloading points in cases
where the P.D. classification is not available, or in cases
where the designer does not wish to determine it.)
For
airfoils in the 12 classification, the load points should be
taken from table 2-V, using the line corresponding to the
In cases where the
Cmac, and the camber of the airfoil.
actual position of load number 1 is less than
inch from
the leading edge, loads 1 and 2 may be combined into a
single load (of twice the unit value) and applied at their
centroid. For ribs having a chord of less than 60 inches,
8 equal loads may be used, their arrangement being such
as to produce shears and moments of the same magnitude
as would be produced by the application of 16 equal loads
at the locations specified above.
For the medium angle of attack condition 16 equal loads
should be used on ribs of chord of 60 inches or greater, 8
In either case
equal loads for chords less than 60 inches.
the total load should be computed as specified.
When
16 loads are used, they should be applied at 8.34, 15.22,
19.74, 23.36, 26.60, 29.86, 33.28, 36.90, 40.72, 44.76, 49.22,
54.08, 59.50, 65.80, 73.54, and 85.70 percent of the chord.

When

loads are used they shall be

comparable results.

4.

6.

as to give

When the lacing cord for attaching the fabric passes entirely
around the rib, all of the load should be applied on the bottom

chord.

5.

so arranged

When the covering is to be attached separately to the two


chords of the rib, the loading specified in paragraph c below
should be modified so that approximately 75 percent of the
ultimate load is on the top chord and 50 percent on the
bottom, the total load being 125 percent of the ultimate load.
The aforementioned load distribution also is applicable for
ribs attached directly to the spar of single spar wings.
58

>

Co

a,

>

S
n

a
c

_,2
<

OS

c o o

Sag

il

59

ft,

chord
O

CN

eo

If

28.9

34.3

41.0

49.0

72.0

90.0

11.3

14.

17.5

21.3

25.5

30.5

36.2

43.2

51.

72.0

90.0

f-

11.0

13.5

16.4

19.7

23.6

28.0

33.5

39.7

47.7

72.0

CO
OS

12.0

14.7

17.9

21.5

25.6

30.1

36.6

41.8

49.7

72.0

CO

o>

24.4

00

20.1

CO

16.3

00

o
o
Oi

(N

O
US

13.1

oo

lO
cd

10.4

CO

>o

Ob
,^

00
tri

O)
c*i

CO
CN

CO

oi

-. 02 to -. 0399

o
pi

0.00 to -. 0199

00

3.0 or greater

00

-. 02 to -. 0399

CO
ci

00 to -. 0199

0.

0.0 to 2.9

CN

Camber

ointsin percen

Load

PD
Classification

Eh<

90.0

C. Test methods.

The ribs should be attached to short spar sections to simulate


conditions in the actual glider. The spar sections should be
supported in such a manner that they will not prevent free
It is satisfactory to mount the spars so
deflection of the rib.
that their edges rest directly on the supporting structure but
they must not be restrained from rolling or twisting. See

fig.

Standard procedure.

2-III.

To simulate the lateral bracing effect given a rib in the actual


wing assembly, it is permissible to employ vertical guide blocks

These guide
along the sides of ribs which are tested singly.
blocks should leave the ribs free to deflect in the direction in
which the load is being applied, should have faces bearing
against the rib which are not wider than 3^-inch, and, for metal
covered wings, should be spaced at least 8 inches apart. For
fabric covered wings these lateral supports should not be closer
than twice the stitch spacing, or the length of the individual
In
rib chord members, or 8 inches, whichever is the greater.
any case, the lateral supports should simulate, as slosely as
practicable, the actual conditions represented in the glider.
In order to avoid local failures of a type not likely to be en
countered in flight, it is permissible to use small blocks not
more than 1-inch long to distribute the load at the loading
points.

WING PROOF AND STRENGTH TESTS


A. Test loads. The loads to be used and their distribution over

the wing will depend upon the particular condition for which the
test is conducted.
In general, when tests are made to prove
the strength of the entire wing, four tests should be conducted
corresponding to the four basic flying conditions of positive
high angle of attack, negative high angle of attack, positive
low angle of attack, and negative low angle of attack. In some
cases, involving cantilever wings, the wings are sufficiently
symmetrical structure wise that only those tests involving the
maximum loadings in the positive direction need be conducted.
B. Test methods.
1 . General. The procedure outlined elsewhere for the prepara
tion of the manufacturer's test report is also applicable to
reports of wing tests.
2. Mounting. For the tests, the wing will usually be mounted
The method of attachment should simulate the
on a jig.

method of attachment in the actual glider. In particular,


the method of attachment should be such that the strength
and rigidity of the jig is not imparted to the wing thereby
leading to erroneous conclusions regarding the strength of
the wing adjacent to the attachment fittings.
See figs.
2-I V through 2-XI.
60

3. Chord component. Usually, the chord of the wing will not


be horizontal but will be inclined so the load laid on the

The angle of inclina


wing will also load the drag system.
tion will be such as to produce the correct chord component
as determined from the stress analysis.
4. Deflections. Numerous deflection measurements should be
taken along the span either at the leading and trailing edges
The points of support should
or at the front and rear spars.
be observed also to see whether or not they move under load.
Measurements should be made at each increment of load
and these values should later be plotted in curve form in the
manufacturer's report, to show the elastic behavior of the
wing under load.

SECTION A - A
Figure 2 III. Example of setup for test of wing ribs.

61

C.

Rigidity. At present,

established

the Federal Aviation Agency has no


criteria for permissible bending deflection in wings.

D. Test report. The manufacturer's report should include all


items peculiar to his particular test, such as computations show
ing the chord component of the test loads and curves of deflec
tions along the span.
The bending deflections should be separ
ated from the torsional deflections and separate curves should
be plotted for each.

CONTROL SURFACE TESTS


Tail surface and aileron tests.
A. Test loads.
1. Kinds of tests. Tests on tail surfaces and ailerons may be
either limit load tests or ultimate tests. In either case, the
2.

3.

loading distribution itself (not the total load) is the same.


Load distribution-tail surfaces. The horizontal and vertical
tail surfaces should be tested for both of the conditions
illustrated in figs. 1-XI, and 1-XII. The magnitude of the
load in each case depends upon which of the specified condi
tions is critical.

Ailerons. Ailerons should be tested for the load distribu


tion shown in fig. 1-XV.

4. Balance area. The

ordinate of the loading curve at the hinge


line is constant over the span.
It is not affected by the chord
of the movable surface.
The unit loading on the balance
area, if any, is the same as at the hinge line as shown in
figs.

1-XII

B. Test methods

and

1-XV.

(see figs.

2-XIII

and

2-XIV.)

1.

Horns. Control

2.

of flexible cables, unless the test is purely a control system


test.
Cable usually stretches excessively, and the resultant
angular deflection of the control surface may disturb the
position of the loading bags or possibly cause them to tumble
onto the floor.
Mounting. The control surfaces may be mounted on the

surface tests should include the horn of the


arm to which the control system is attached.
Control sur
face horns should be rigidly held by tubes or straps instead

glider provided that cables are eliminated and that the fuse
lage or wing is either supported rigidly or its movement at the
attachment fittings of the control surfaces is accurately
measured.
If the surfaces are mounted on a jig, the jig
should be so constructed as to simulate the attachment condi
tions applying in the glider.
62

SlHOINdfl

oi

v
ajn6jj

w-Z

QNV

dnjas

SXNVId

Aiddv

i<y jsa/ jo ajajduio]

Ol

lN3A3>ld

avoi

6uim

puo S|i juauiipojjo

o/ ai/|

-sSD/asnj

64

65

66

Fabric covering. When the unit tested is a fabric covered


surface, the fabric should be installed as for service except
that only the primer coats of dope should be applied, in order
to leave the covering slack.
The load should be applied
The final coats of dope can be
directly to the covering.
applied subsequent to the tests.
which total
load is based

Span upon

4
_.nti-

--.-in:

-It---

iH

-2SNOTE

a = Nose rib
b = Nose former

2S = Length of test assembly


TEST ASSEMBLY

FOR LEADING EDGE

HAVING ALTERNATE

NOSE

RIBS

AND NOSE FORMERS


Figure 2-IX.

Test attembly

so

6.

During

the test all brace wires must be rigged


that they are at least as tight as they would ordinarily be
in service.
If any wires become slack during the test, that
fact should be noted in the report and a statement given
concerning the approximate load at which it occurred.
Load application. The test load can usually best be applied
by means of bags of sand or lead shot, so distributed as to
represent the required loading.
In the case of a test for the so-called "balancing" condition,
it should be noted that all the load acts in one direction on

4. Brace wires.

5.

tor leading edge having alternate note ribs and nose formers.

the fixed surface.

C. Test report. In all cases the manufacturer making a test is


required to submit a complete report covering details of tests.

The report should include photographs or drawings of the test


setup and the test specimen; photographs of failed parts or
sections; records of deflections and readings taken; date of test;
67

Figure 2X. Typical $etop for tett of a box type wing beam and lit attachment to the tutelage.

68

69

70

identification number of report; serial and model number of


glider and signature of responsible witnesses and/or test per
sonnel.
In addition, the following points should be covered
when applicable :
1 . Substantiation by references or computations of the selection
of critical test conditions and loadings.
2. Loading schedule used in the test.
3. Description of test setup, with reference to drawing numbers.

Flap
A.

B.

tests.

Test methods and loads.


Wing flaps should usually be tested on a jig because of the
difficulty of mounting a complete wing and flap assembly in
the inverted position.
In all cases, however, the test should
include the supporting brackets and their means of attach
ment to the wing. The test will be similar to that for an
aileron or elevator except that the load distribution over the
surface will usually be uniform instead of decreasing toward
the trailing edge, as is the case for the ailerons, rudder and the
elevator.
If it is necessary or advisable to test the flap sup
as
in the wing, that may be done, without
installed
ports
inverting the wing, by running cables from the flap hinges up
and over pulleys to a loading platform.
Test report. In all cases the manufacturer making a test is
required to submit a complete report covering details of tests.
The report should include photographs of drawings of the test
setup and the test specimen; photographs of failed parts or
sections; records of deflections and readings taken; date of
test; identification number of report; serial and model number
of glider and signature of responsible witnesses and/or test
In addition, the following points should be covered
personnel.
when applicable :
1. Substantiation
by references or computations of the selec
tion of critical test conditions and loadings.
2. Loading schedule used in the test.
3.

Description of test setup, with reference to drawing numbers.

Control system tests.

A. Test
1.

loads.

Operating test. The controls should be operated from the


pilot's seat when the system is sustaining the "limit" loads
specified in Chap.

2.

1.

Strength tests. The test loads used in a limit load test or an

ultimate test are premised either on the control surface design


loads or on the control system design loads depending on the
particular limiting conditions. This is explained in Chap. 1.
71

B. Test methods.
1.

Method of load application. A control system test should be


conducted only upon a fully installed system in the actual
aircraft. The load may be applied in either of the following

ways:
(a) The control system for the main surfaces may be rigidly
secured at the normal point of contact with the pilot's
hand or foot and the surfaces are then loaded.
This
method has the disadvantage that stretching of the con
trol system cables may result in movement of the sur
faces thereby causing the loading bags to shift in position
or possibly tumble onto the floor. The control systems
for adjustment devices such as the stabilizer and the
trailing edge tabs, and wing flaps are usually of irreversi
ble type such that no additional fixation should be neces
sary during the tests. The type of blocking used at the
control wheel, the control stick, or the rudder pedal
should be such that it can readily be removed and
replaced with the system under load, and so that when
removed it will not interfere with limited movement of
the controls.
Simple blocking of the control stick and
tying the rudder pedal in position by a wire or cable,
are usually satisfactory methods of accomplishing this.

STABILIZER

RIB.

REAR

SHEAR WEB

SHORT SECTION
OF STABILIZER

TEST

ASSEMBLY

CANTI LEVERED
FROM

WEIGHTS

FIXTURE

Figure 2XIII. Typical teft of a contro/ surface hinge bracket and lit attachment to wing.

72

o
LL.

LU
I

73

(b)

2.

3.

The control system for the main surfaces may be secured

as in (a) and the load applied to the control surface


horns or other outer extremities of the system by the use
of cables leading over pulleys to a loading platform.

Application. The test loads should be applied, if practicable,


under conditions which produce the most critical loads in
For instance, push-pull tubes should be loaded
the system.
Also, brackets and
in compression rather than tension.
fittings should be loaded under the most critical conditions
if there exists a variation in strength or loading throughout
the range of movement of the control system.

Operation test. The purpose of the operating test is to deter


mine that the controls and their attachment fittings are free

from binding, jamming or excessive friction or deflection at


the specified operating test loads.

4. Ultimate load test. The purpose of a control system ultimate


test is to ascertain that all parts of the system have sufficient

Ultimate load tests should


strength and rigidity for service.
be conducted when the combination of stress analyses and
limit load tests are not considered satisfactory criteria of
strength. During the ultimate load test the loads should be
carried to the limit load values and then removed to make
sure that no undue permanent deflections up to the limit
load values are within the elastic limit of the materials used
in detail parts of the system.

C.

Rigidity. Extra-flexible cable as used in control systems


sometimes will stretch a relatively large amount when sub
jected to its limit or ultimate loads even though of adequate

size and prestretched. Although not particularly desirable this


does not impair the airworthiness of a system unless the deflec

tion is excessive.

D. Test report. In all cases the manufacturer making a test is


required to submit a complete report covering details of tests.
The report should include photographs or drawings of the test
photographs of failed parts or
sections; records of deflections and readings taken; date of test;
identification number of report; serial and model number of
setup

and

the test specimen;

glider and signature of responsible witnesses and/or test per


In addition, the following points should be covered
sonnel.
when applicable
1.

2.
3.

Substantiation by references or computations of the selection


of critical test conditions and loadings.
Loading schedule used in the test.
Description of test setup, with reference to drawing numbers.
74

Fuselage tests.
A.. Test loads.
1.

is,

2.

The test loads for a fuselage usually comprise the torsion and
bending loads corresponding to the "ultimate" or "limit"
loads for the tail surface structure.
The horizontal tail
surfaces, being symmetrically placed, introduce straight
bending loads in the fuselage structure which during the
tests are resisted by the wing reactions and the weights for
ward of the center of gravity.
The loads from the vertical
tail cause a bending moment which during the tests is
resisted by the wing reactions. For the landing conditions
the fuselage will be loaded by inertia loads and the landing
gear (wheel or skid) reactions.
Two separate tests should be conducted, one for each type of
loading. For the bending test the loads are so chosen and
placed, if possible, as to represent the most severe loading
If the
condition or conditions for all parts of the fuselage.
upper part of the fuselage appears to be weak, it should be
tested for upward acting tail loads.
Usually, however, the
downward acting loads are critical. For the torsion test
the fin and
there is only one condition to consider, that
rudder load.

Test methods.

General. The

is

1.

general structural test procedure outlined


elsewhere can also apply to fuselage tests.
mounted
2. Bending test. For the bending test the fuselage

if

is

is

in horizontal position and


held in place only by its wing
either right side up or upside
attachment fittings. It
down depending upon the loading conditions. Tail surface
loads are applied through the stabilizer attachment fittings
and loads representing weights in the fuselage,
used, are
laid inside or suspended at their proper locations along the
fuselage.

mounted
Torsion test. For the torsion test the fuselage
on its side, with the longitudinal axis horizontal, and held
in place
only by the wing attachment fittings. If the fin
on the fuselage, the test load
laid directly on
distributed
so as to locate the center of pressure of the load in its proper
Otherwise, some means of applying the correct
place.
torsion, shear and bending loads through the fin attachment
Unless the fin
of cantilever con
fittings must be devised.
will be necessary for this test to have both the
struction
fin and stabilizer mounted on the fuselage.
See fig. 2-XII.
states that
un
Towing and launching loads. Chap.
to
and
loads
aft
investigate
launching
towing
of
necessary
However, in testing for these conditions,
the front spar.
loads must be applied at points aft of the rear spar to resist
75

is

it

4.

it

is

is

it,

is

is

3.

the test load on the towing hook. Care should be taken in


testing for these conditions to guard against overloading such
For instance, if the side load is
portions of the fuselage.

resisted only by the front strut fitting and the tail post, the
loading in the rear part of the fuselage might be higher than

The solution in
the design load and failure would occur.
this case would be to apply a moment at the wing-root fittings
and at the strut points as well as at the tail, each of which
would be less than the ultimate loads for which the fuselage

is designed.

In actual flight,

5.

the loads on the tow line, especially side

by inertia loads as well as by air loads.


Accordingly, this should be given careful consideration in
determining the magnitude and location of the fuselage test
For example, much of the side load will be resisted
reactions.
inertia
of the wing, through the wing-root fittings,
by the
while the vertical components of the towing loads will be
resisted mainly by the inertia of the various items of mass
in the fuselage, the loads being applied through their points
of attachment to the fuselage.
Reference is made in Chap. 1 to the resultant effects on the
strength of the wing root fittings and adjacent structure
from unsymmetrical loads.
The comments of the preceding section regarding testing
for towing loads apply also to landing gear static tests. Care
should be exercised so that no part of the fuselage is over
loaded locally at points where high loads would not normally
be expected during actual landings.
Deflection readings should be taken at each
Deflections.
increment of load, at various strategic locations, including
the wing attachment fittings, the rear end of the fuselage
and, for the torsion test, the tip of the fin.

loads,

are resisted

C. Test report. In all cases the manufacturer making a test is

required to submit a complete report covering details of tests.


The report should include photographs or drawings of the test
setup and the test specimen; photographs of failed parts or
sections; records of deflections and readings taken; date of test;
identification number of report; serial and model number of
glider and signature of responsible witnesses and/or test per
sonnel.

In addition,

when applicable

the following

points should be covered

by references or computations of the selec


tion of critical test conditions and loadings.
(b) Loading schedule used in the test.
(c) Description of test setup, with reference to drawing numbers.
(a) Substantiation

76

77

FLIGHT LOAD TESTS

In

general,

the demonstration of strength by means of flight load

tests is not recommended.

Any proposals for such tests should

brought to the attention of the regional

study and recommendations.

office concerned

be

for special

FLUTTER AND VIBRATION


Flutter and vibration prevention tests. Wings, tail, control surfaces,
tabs, wing spoilers, and dive brakes should be demonstrated to be free

from flutter at all airspeeds and altitudes within the design speed range
Freedom from flutter may be demonstrated either by a
up to VD.
formal flutter analysis, by compliance with acceptable simplified
flutter prevention criteria or by an acceptable flight flutter test.
Ground vibration tests. The natural frequencies

of all main struc


tural components should be determined by ground vibration tests.
These tests should determine at least the following resonant modes of
vibration: Wing first symmetrical and unsymmetrical bending and
wing torsion, symmetrical rotation of ailerons about their hinge lines,
wing spoiler rotation about its hinge line, dive brake rotation about
its hinge line, fuselage torsion, fuselage side bending, fuselage vertical
bending, fin bending, stabilizer bending, rotation of tabs about their
hinge lines.

Simplified flutter criteria. Studies have indicated that for a con


ventional airfoil in which the center of gravity of the airfoil section
is not too far back, wing flutter could be prevented by designing for a
certain degree of wing torsional rigidity and by control surface

dynamic balance, whereas empennage flutter could be prevented by


providing a degree of control surface dynamic balance.
Satisfactory
rational analytic methods have been available for a number of years
which would permit an engineer to carry through computations to

determine the flutter stability of a specific design.


In view of the
fact that flutter is an aeroelastic phenomenon which is caused by a
combination of aerodynamic, inertia and elastic effects, any criteria
which does not consider all three effects is bound to have severe limi
tations. That this is so is evidenced by the fact that in almost all
cases where rational analyses have been carried through for specific
designs

it has been found that the balance requirements specified by

the simple criteria have been too severe.

Although a rational flutter


of the simplified criteria contained

analysis is to be preferred to the use


herein (since in most cases a better design may be achieved by reduc
ing or eliminating the need for nonstructural balance weights), the
application of these criteria to conventional aircraft is believed to be
adequate

to insure freedom from flutter.


78

WING FLUTTER CRITERIA


The following wing flutter criteria should be applicable to all con

ventional gliders which do not have large mass concentrations on the


wings.

Wing torsional stiffness. The wing torsional flexibility factor


F defined below should be equal to or less than 200

Where:

W'

F-feC'rfs

8,

Wing twist at station i, per unit torsional moment


applied at a wing station outboard of the end of
the aileron.

(radians/ft.-lb.)
chord
at station i, (ft.)
Wing
length
Ct
=
ds
Increment of span (ft.)
Vo=Design dive speed mph (IAS)
=

Integration to extend over the aileron span only. The value of the
above integral can be obtained either by dividing the wing into a
finite number of spanwise increments AS over the aileron span and
summing the values of QtCfAS or by plotting the variation of
over the aileron span and determining the area under the resulting
curve.

In order

the wing flexibility factor F, a pure torsional


be
couple should
applied near the wing tip (outboard of the end of the
aileron span) and the resulting angular deflection at selected intervals
to determine

The test can best be performed by apply


along the span measured.
ing simultaneously equal and opposite torques on each side of the
glider and measuring the torsional deflection with respect to the glider
The twist in radians per unit torsional moment in ft.-lbs.
center line.
should then be determined.
If the aileron portion of the wing is
divided into four spanwise elements and the deflection determined at
the midpoint of each element the flexibility factor F can be deter
mined by completing a table similar to table 2-I. Fig. 2-XV illus
trates a typical setup for the determination of the parameters C
and

AS.

Aileron balance criterion. The dynamic balance coefficient


should not be greater than the value obtained from fig.
2-XVI wherein
is referred to the wing fundamental
line
and
the
aileron hinge line. If no knowledge
node
bending
exists of the location of the bending node line the axis parallel
to the fuselage center line at the juncture of the wing and
fuselage center line at the juncture of the wing and fuselage

K/I

K/I

can be used.

Wherein:

K= product

of inertia

/=mass moment of inertia of aileron


hinge line

79
657822 O - 62 - 7

about its

TABLE
(3)

(4)

(5)

AS

C2

ft

ft

ft*

rod

(2)

(1)

STATION

ft

(6)

0C2aS
lb

1
2
3

4
F=

Z column

(6)

Figure 2 -XV.

l-II

Table

FLIGHT CONDITION

(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)

(H)
(12)
(13)
(14)
(15)

Item

No.

W = design weight, pounds

V = velocity m,.p.h
q = .00256 VJ = .00256
s=(l)/S

(2)1

q/s= (3)/(4)
m = limit wing load factor
Cat

C,

n* = (8) x (5)

Cm
mr = (10) x (5)
113= tail load factor

02=

-(6) -(12)

n* =
(9)
T= (1) x (12).

80

Ii

II

III

nil

IV

Free play of ailerons. The total free play at the aileron edge
of each aileron, when the other aileron is clamped to the wing
should not exceed 2.5 percent of the aileron chord aft of the
hinge line at the station where the free play is measured.

Frequency of ailerons, dive brakes, or spoilers. The frequency


of the ailerons rotating symmetrically about their hinge lines
(both ailerons moving together) should be at least 1.5 times
the frequency of the fundamental symmetrical wing bending
frequency. The frequency of rotation of dive brakes and/or
wing spoilers about their hinge line, for any position from
closed to open, should be at least 2 times the wing torsion
frequency.

EMPENNAGE

FLUTTER CRITERIA

The following empennage flutter criteria are applicable only if the


empennage configuration is conventional and consists of a single verti
cal fin and rudder and a fixed horizontal stabilizer and elevators.
1. Elevator balance. Each elevator should be dynamically balanced
to preclude the parallel axis flutter (fuselage vertical bending-symmetric elevator rotation) as well as perpendicular axis flutter (fuselage
If, however, the anti
torsion antisymmetric elevator rotation).
symmetric elevator frequency is greater than 1.5 times the fuselage
torsional frequency the perpendicular axis criterion need not apply.
a. Parallel axis criterion. The balance parameter y as obtained
from fig. 2-XVII should not be exceeded. In fig. 2-XVII the
balance parameter y and the flutter speed parameter Vf are
defined as:

bSff

Where

Sp = Elevator

/
6

static balance about hinge line (ft.-lbs.)


Elevator mass moment of inertia about the hinge
line (lb.-ft.2)
=Semichord of the horizontal tail measured at the
midspan station (ft.)

VD-(m.p.h.)

Fuselage vertical bending frequency (c.p.m.)


b. Perpendicular axis criterion. Need not apply if the antisym
metric elevator frequency is greater than 1.5 times the fuselage
torsion frequency. For each elevator the balance parameter X
as obtained from fig. 2-XVIII should not be exceeded.
In
X
the
flutter
2-XVIII
the
and
balance parameter
speed para
fig.
meter Vf are defined as :
fh

Vf

bja
81

82

Where

of horizontal tail (ft.)


Semichord of horizontal tail at midspan station (ft.)
K = Elevator product of inertia referred to stabilizer
center line and elevator hinge line (lb.-ft-2)
= Elevator mass moment of inertia about the elevator
Semispan

b =

fa

hinge (lb.-ft.2)

Fuselage torsional frequency (c.p.m.)

2. Rudder balance. The value of 7 as obtained from fig. 2-XVII


and the value X as obtained from fig. 2-XVIII should not be exceeded ;
bK and :
where in figs. 2-XVII and 2-XVIII,
bSp, .

y=~X=ST

Distance from fuselage torsion axis to tip of fin (ft.)


Semichord of vertical tail measured at the 70-percent

b =

span

position (ft.)
of inertia of rudder referred to the fuselage torsion
axis and the rudder hinge line (lb.-ft.2)
= Fuselage torsional frequency (c.p.m.)
= Fuselage side bending frequency (c.p.m.)
= Rudder static balance about hinge line
(lb.-ft.)

K = Product
fa
/,
Sp

Mass moment of inertia of the rudder about hinge


(lb.-ft.2).

All reversible

line

TAB FLUTTER CRITERIA


tabs should be 100 percent statically mass balanced

about the tab hinge line. Tabs are considered to be irreversible and
need not be mass balanced if they meet the following criteria:
1.

For any position of the control surface and tab, no appreciable


deflection of the tab can be produced by means of a moment

applied directly to the tab, when the control surface is held in


a fixed position and the pilots tab controls are restrained.

2.

The total free play at the tab trailing edge should be less than
2.5 percent of the tab chord aft of the hinge line, at the station
where the play is measured.

3.

The tab natural frequency should be equal to or exceed the


value given by the lower of the following two criteria

S,

48FD
^ f'=~cfs~e
,

>

or

(b)

C'P"m'

2,000 c.p.m. for gliders

less than 200 m.p.h.

Thus for a glider with

having a design speed of

than 200 m.p.h. if (a)


above gave a value in excess of 2,000 c.p.m. it would only be necessary
to show a frequency of 2,000 c.p.m. for the frequency criterion.
a design speed less

83

84

85

Where:

/, = lowest

natural frequency of the tab as installed in the


glider (c.p.m.) either tab rotation about the hinge
line or tab torsion whichever is lower.

Ce

- Chord

of movable control surface aft of the hinge line,


at the tab midspan position (ft.) .

S, -Span of tab (ft.)


Se

- Span

of movable control surface to which tab is at


tached (both sides of elevator, each aileron and rudder)
(ft.)

Particular care should be taken in the detail design to minimize the

possibility of fatigue failures which might allow the tab to become free
and nutter violently.

Balance weight attachment criteria. Balance weights should be dis


tributed along the span of the control surface so that the static unbal
However,
ance of each spanwise element is approximately uniform.
where a single external concentrated balance weight is attached to a
control surface of high torsional rigidity the natural frequency of the
balance weight attachment should be at least 50 percent above the high
est frequency of the fixed surface with which the control surface may

For example the aileron balance weight


in a nutter mode.
frequency should be at least 50 percent above the wing fundamental
couple

torsional frequency. The balance weight supporting structure should


be designed for a limit load of 24g normal to the plane of the surface
and 12g in the other mutually perpendicular directions.

It

K/I
K

can
should be noted that the dynamic balance coefficient
and
or (3) reducing
be reduced by (1) reducing K, (2) increasing
/.
Since
an
increase
in
results
in
a
reduced
control
sur
increasing
face natural frequency with possible adverse flutter effects, the
primary purpose of ballast weights used to reduce K/I, should be to

decrease the product of inertia

ment of inertia

/.

K and

not to increase the mass mo

Flight flutter testing. Various procedures are available for demon


strating freedom from flutter, namely: Performance of a flutter
analysis, application of the simplified criteria as discussed above,
when applicable, and performance of a flight flutter test by the
It is not recommended that flight flutter tests be used as
applicant.

procedure for substantiating freedom from flutter. The


performance of a flutter analysis or the application of the simplified
flutter criteria are considered preferred procedures due to the hazards
It is recommended that flight flutter
involved in flight flutter tests.
a general

tests be performed only when allied investigations or engineering


evaluations give some assurance that the tests may be performed
86

safely. A flight flutter test program may involve flutter substantia


tion of two or more control surfaces whose static unbalance values are
in excess of the allowable values in the simplified flutter criteria.
As a precautionary procedure, it is recommended that tests be per
formed for one surface at a time with the remaining unsubstantiated
control surfaces balanced to at least the degree indicated necessary
by the simplified flutter criteria.

(a) Acceptability. Flight flutter tests


stantiation of freedom from flutter when
such tests that proper and adequate

will be acceptable

it

as sub

can be demonstrated by

attempts to induce flutter have

been made within the speed range up to VD, and the vibratory response

of the structure during the tests indicates freedom from flutter.


(b) Records.

Flight recording instrumentation of either the elec

trical or photographic type should be installed to provide a perma


nent record of the control surface and/or fixed surface response to the
applied flutter exciting forces, as well as a record of the associated test
airspeed.
(c)

Test procedure. The following is an outline of an acceptable

(1)

The tests should cover the flight speed range with excitation

procedure for demonstrating freedom from flutter by flight tests in


which rapid control surface deflections are applied to induce flutter:
applied at small incremental increases of airspeed up to VD.
The incremental speed increases between 0.8 VD and VD should

not be more than 5 m.p.h. At lower flight speeds, larger


increments of airspeed may be used.

The controls should be deflected to attempt to excite flutter

(2)

follows

(3)

as

Aileron control to induce wing and aileron flutter.

Kudder control to induce rudder and vertical tail flutter.

Elevator control to induce elevator and horizontal tail flutter,


and symmetric wing flutter.

Control surface to which the tab is attached to induce tab


flutter.
Attempts to induce flutter should be made by abrupt rotational
These deflections
deflections of the respective control surfaces.
should be obtained by striking the corresponding control with
the free hand, or foot, and

the disturbed control should be

allowed to stabilize without restraint by the pilot. The force


applied should be sufficient to produce an impulsive deflection
of the control surface of at least 3 degrees.

(4)

At

attempts to induce flutter should


be made for each of the surfaces being investigated.
each test speed, at least

87

A permanent record* at

(5)

each test speed should be obtained as


follows:
In flutter tests of the rudder, elevator and tab surfaces; a time
history of the control surface rotational deflection, and the
associated airspeed.
In flutter tests of the wing and aileron; a time history of the
aileron rotational deflection, a time history of the wing vibra

tory response, and the associated test airspeed.


(6) The tests should consider significant variations in mass and
rigidity values which might be expected in service. The aileron
and tab control systems should be freed to the extent necessary
to be representative of what might be expected in service.
The
tests should be conducted at altitudes of approximately
(7)
50 to 75 percent of the maximum operating altitude.
The
vibration survey should be conducted prior to performing
(8)
The structural frequency and vibration
the flight flutter tests.
mode data should be evaluated to determine what structural
modes are most likely to be flutter critical.
(9) The resulting oscillations of the wing and/or control surfaces
in response to the excitation applied shall be damped with no
tendencies to persist at any test speed.

These data can be obtained by installing a control


surface position indi
cating device at the control surface, a vibration pickup in the vicinity of one
wing tip to detect the wing response, and a suitable pressure transducer con
system to measure the airspeed with the
nected to the aircraft's pitot-static
electrical signals from these instruments connected to a recording oscillograph.
Alternatively, photographic
methods using cameras may also be used for
However, the photographic
recording the flight test data.
records obtained
should be of a nature that will permit satisfactory evaluation of the degree of
of
control surface deflection applied, the flutter stability and a correlation
the airspeed record with the associated flutter test point.

88

Chapter

3 DESIGN, CONSTRUCTION AND


FABRICATION

The primary structure should not incorporate design details which


has shown to be unreliable or otherwise unsatisfactory.
The suitability of all design details should be firmly established.
Products such as bolts, pins, screws, tie-rods, wires, terminals, et
cetera, used in the primary structure should be of aircraft standards
as established by the SAE or as established by government aircraft
standards and specifications or TSO's.
Strength values contained in
experience

MIL-HDBK-5, ANC-18, andMIL-HDBK-17,

and

ANC-23 Part

II,

should be used unless shown to be inapplicable in a particular case. The


primary structure should be made from materials which experience or
conclusive tests have proved to be uniform in quality and strength and to
The methods of fabrica
be otherwise suitable for glider construction.
tion employed in constructing the primary structure should be such
as to produce a uniformly sound structure which should also be reliable
with respect to maintenance of the original strength under reasonable
service conditions.
The workmanship of the primary structure
should be of sufficiently high grade to insure proper continued func
tioning of all parts. All members of the structure should be suitably
protected against deterioration or loss of strength in service due to
weathering, corrosion, abrasions and other causes. Adequate provi
sion for ventilation and drainage of all parts of the structure should
be made.
(See also FAA Technical Manual No. 103 "Aircraft De
sign Through Service Experience.")
PROCESSES

Detailed information on assembly processes will be found in CAM


18, "Maintenance, Repair and Alteration of Airframes, Powerplants,
Propellers and Appliances," available from the Government Printing
Bulletin ANC-19, "Wood Aircraft Inspec
Office, Washington, D.C.
tion and Fabrication" also includes detailed information on the
properties and fabrication techniques of various woods and wood
materials and associated data on aircraft glues.

The more elementary

WING DESIGN

types of gliders usually call for inexpensive


construction,
with
parts which are easy to construct and
simple
wing
Typical construction of this type is the two-spar wing
assemble.
89

if

is

is

is

is

it

if

is

it,

14

if

is

is

is

if

is

is,

having a drag truss composed of fore and aft drag struts and single
Where double drag wires, that
top and
drag and antidrag wires.
bottom drag wires, are employed, the torsional stiffness of the wing
single drag wires are employed.
greater than
If the general planform of the wing rectangular, and the spars
For instance, in the
are parallel, construction
relatively simple.
layout of fittings, most of the angles would be right angles, and the
problems of load determination would be two dimensional. In
wings with rectangular planform, most of the ribs would be of identi
In contrast, the general planform of the wing
cal construction.
tapered, then the construction becomes more complicated, as evi
denced by the fact that the spars would necessarily taper in depth and
each rib would be different due to the effect of taper. However,
there are many advantages to the tapered wings.
Usually, they are
more efficient structurally and aerodynamically.
The wing struc
tures of most gliders of advanced design are currently comprised of
D-nose and special drag strut intersecting the main
single spar with
The single spar with D-nose type
spar at about the
-span point.
of construction requires careful workmanship, especially in laminating
the spar and in attaching the nose cover over the supporting noseribs.
The single spar D-nose type of wing construction lends itself to
metal as well as wood construction.
Metal has the disadvantages
and the
that special skill, tools and machines are required to work
that
the
structure
not
fact
usually
highly enough loaded to permit
Also, metal working tools and
the most efficient use of the material.
are
more
than
wood
machinery
working tools and machin
expensive
The minimum gauges of material usable from the standpoint of
ery.
handling, workability, and corrosion resistance and, in some cases,
the minimum gauges available commercially, often exceed that needed
of metal
to carry the design loads.
Consequently, the structure
particular wing of relatively small
may be somewhat heavy. For
thickness, but having
high aspect ratio and high design loading,
probable that metal construction would be as light and efficient as
wood.
Particular care must be used in the design of the wing-to-fuselage
attachment fittings of single-spar wings.
In some cases secondary
member run back from the spar at an angle connecting into the rear
chordal point corresponding approximately to the
root fitting at
rear spar position in
carried
two-spar wing. The nose covering
back to this member; to give structural stability, two pins at the root,
one forward, and one aft are necessary for an externally braced wing.
Full cantilever wings require horizontal pins at the top and bottom
of the spar, or one vertical pin full depth at this point, and another
pin aft to take out the drag and torsion reactions. Some wings have
another pin at the leading edge to increase the rigidity, but this
not
90

in order to get a rigid structure. It is desirable that the


two lower horizontal pins be in line fore and aft so when the third
pin or strut is removed the wing will hinge down for ease of assembly
or knock-down; otherwise critical loads may be imposed on the fittings
due to the dead weight of the wing.
Torsional stiffness. It is essential that the wing structure have
adequate torsional stiffness in order to insure freedom from flutter
and other undesirable characteristics. In contrast to metal or ply
wood covered wings, fabric covered wings usually lack torsional
necessary

rigidity.

Wing design details. Wing spars. Provision should be made to


reinforce wing beams against torsional failure, especially at the point
of attachment of lift struts, brace wires and aileron hinge brackets.
Solid wood spars. Solid wood spars should be made of Grade A
They may be tapered in depth or thickness, but should not
spruce.
be thinner than
-inch at any point.
Built-up wood spars. Of the built-up types of spars, the ibox with
smooth plywood faces with single upper and lower flanges is the most
convenient for attaching ribs. It has half as many flanges to make as
the "I" type.
In either type, blocking must be provided at all
points where fittings are attached.
Blocking should be tapered off
at the ends to avoid concentration of stress in the flanges.
Inter
mediate verticals are provided in some cases to increase the allowable
stress in the webs.
These verticals need not be filleted at the ends
unless they also carry a concentrated load to be distributed into the
On box spars the attached rib vertical sprovide this
spar web.
stiffening effect on the webs. CAM 18 shows details of spar con
struction.

Top and bottom spar flanges are usually proportioned according


to the relative magnitudes of the critical bending loads in each direc
tion such that the corresponding margins of safety will be approxi

mately equal.
Spar webs are usually made of spruce, mahogany, or birch plywood.
These are usually of three-ply construction, but special two-ply and
45-degree constructions are available in spruce and mahogany,
providing somewhat higher allowable stresses. The face grains of
3-ply should be laid vertically on the spar.
Splices should be vertical,
over
a
preferably
stiffener.
Laminated spars may be spliced in either plane, and splices in the
various laminations should be spaced well apart. Splices in solid
spars, if any, should be in the vertical plane, as shown in CAM 18.
Splices in wood spars. Splices in structural wood members when
The surfaces should
necessary should have a 12 to 1 slope or greater.
be fitted for perfect uniform contact before gluing. Accordingly, the
surfaces preferably should be formed with a planer.
The dimensions
91

Care
and type of splice should be similar to those given in CAM 18.
should be taken in clamping glued splices to use thick "cushion"
blocks of the proper slope and size so as to produce clamping action
perpendicular to the line of the splice, uniformly distributed, and not
A finished splice
such that the pieces tend to slip past each other.
in wood or plywood should show no change in cross section at the

splice.
Wood leading edge. Ordinarily 3-ply plywood leading edge material
The best arrangement, however,
is laid with the face-grain spanwise.

is to use material having face-plies at 45 degrees, center-ply running


In any case, the material must be securely fastened at
spanwise.
each rib in order to develop its full strength.
Splices in the nose
A minimum thickness of Kcovering should be made over a rib.
inch for spruce or mahogany leading edge material is recommended.
On designs where the leading edge covering comes to the spar, the
latter can be built full depth of the wing, with a saving of weight over
the type which is run under the rib cap strips and then built up flush
with spacer strips between ribs. The nose cover serves to gusset
the nose ribs to the spar, and an additional gusset with face grains
running chordwise should be provided to attach the cantilevered tail
ribs. Sufficient glued area must be provided to the face of the spar
A smoother covering can
to carry the vertical shear from the ribs.
be obtained by scalloping the leading edge covering back past the
spar between ribs, to keep the fabric from pulling abruptly over the
sharp edge of the spar.
Wood ribs. Rib spacing under a stressed torsion-nose depends on
the thickness of the plywood and the curvature.
Usual practice
is about 6-inch spacing with 12-inch spacing for tail ribs.
This can
be increased where the limit stress is very low, but sufficient ribs
should be provided to hold the surface true and prevent "oil canning."
Roughly, the maximum spacing for nose ribs should not be greater
than the nose-rib chord, preferably less.
It is recommended that a leading edge spanwise strip be provided
under the cover for support and for drag load in the single-spar wing.
The greatest cross sectional dimension of the strip should be fore
and aft.
Nose ribs should be stiff enough to allow the nose covering to be
The lightest practical method of
clamped down hard for gluing.
getting the required stiffness is to build the rib up out of approxi
mately square materials and carry the joint gussets the full length of
the cap strips so as to increase the bending stiffness of the caps
Nose-rib caps must be heavier in order to avoid
between supports.
splitting when the covering is to be nailed on than when the glue
work is only clamped.
End ribs and corner ribs should be braced or specially designed to
A double set of ribs
provide stiffness against fabric tension loads.
92

GUSSETS

PLYWOOD -FULL LENGTH

STRAIGHTEN AT
Figure 31. Trailing edge constructions.

93

RIBS

94

two or three inches apart and connected with a plywood cap top and
bottom is effective, or a rib with members four or five times normal
width will usually provide the necessary stiffness.
Trailing edges. Typical laminated trailing edges are shown in
Bent-up metal trailing edges are also used, but are more
fig. 3-I.
difficult to attach satisfactorily to the ribs. In any case, trailing
edges must be strong enough to withstand considerable rough handling
when setting up the glider.
Wing tip bows. Wing tip bows are frequently made of wood,
laminated, or steel tubing attached by welded clips bolted to the spars.
The lower surface of tips should be covered with metal or plywood for
protection.
External brace struts.
Struts may be wood, or metal tubing, either round with fairing
or streamlined in shape.
Material is either steel or aluminum
alloy.
The wooden struts are usually tapered and are made up solid
and of square or rectangular section with plywood fairing.
The end fittings must be carefully designed to transmit the
tension loads into the wood portion.
Steel struts usually have the end fittings welded on so that
However, in
the load is carried through the weld in shear.
the case of aluminum alloy struts the fittings are riveted or
bolted onto the end of the strut. A typical end fitting for a
streamline steel strut is shown in fig. 3-I. For a single
strut, it is desirable to provide universal end fittings similar
to fig.

3-II,

b.

Care should be taken in the design of the attachment of struts


and wires to avoid eccentric loads tending to roll the spar or
bend it in the weak direction. This can be avoided on twospar wings by providing a deep drag strut near the strut point
On single-spar wings it is
capable of stabilizing the spars.
desirable to keep the strut axis under the spar axis.
In connection with single-apar braced wings employing air
foils which have a large center of pressure travel, it is desirable
to provide for some freedom at the strut attachment to allow
for flexing of the wing without straining or introducing danger
A serious secondary load
ous secondary loads into the strut.
could be imposed on the strut when flying at a low angle of
attack into a "down" gust unless the wing is exceptionally
rigid or freedom to flex is provided by means similar to a
Ball and socket joints are difficult to design
universal joint.
and are not recommended.
Jury struts. When clamps are used for the attachment of jury to
lift struts, the design should be such as to prevent misalignment or
local crushing of the lift strut.

95

I
657822 O - 62 - 8

Wing fittings. In designing wing-root fittings, care should be taken


to box or brace the extending flat ears at the attachment bolts or
pins so that the drag loads will not induce appreciable
bending
stresses in the ears.
This also applies to fittings at strut, or wire
attachment fittings that may have side load components as well as
This can usually be accomplished
compression and tension loads.
by welding on a shear plate to form a three-sided box, or by bracing
with an external web on one or more sides of the fitting.
If clevis
are
in
used
place of bolts to connect the two parts of a fitting,
pins
the fitting should be designed accordingly.
Particular care should
be made to provide the extra rigidity in fittings that would normally
be provided by the clamping action of bolts and nuts.
It should be
pointed out that the load distribution in a particular fitting may
differ when the attaching bolts and nuts are replaced by clevis pins
and safety pins.
Bolts for attaching fittings to spars are passed directly through the
spar, or through suitable bushings which have for their purpose to
increase the bearing area in the wood.
Care should be taken not to
weaken the spar by too close spacing of bolts, or reduction of the
effective section moment of inertia below the critical value. If
necessary, the spar can be padded out locally by laminating to in
Ash or maple is sometimes used for this when
crease the spar width.
the stress is high as it gives greater bearing strength under the bolts
Unless ash or maple is used under fittings, soft wood should always be
built up locally with a layer of birch plywood to prevent crushing
under the fittings and bolts, and to prevent splitting of the spar.
Care should be taken to have all bolts in wood spars stressed only
axially and/or in shear, wherever possible, as bending on a bolt is
Bolts passing through wood should
more likely to split the wood.
always be provided with the large bearing washers where there is no
For grouped bolts, it is desirable to
fitting to serve this purpose.
on
the
back
side to distribute the load over a
a
plate
single
provide
large area, rather than to provide separate washers for each bolt.
Examples of good and bad fitting designs are given in fig. 3-VII.
Fabric covering.
The fabric should be well finished with dope to provide a
smooth surface essential to high performance.
A
rough surface is conducive to high skin-friction drag. Since

the drag of a well designed high performance glider is mostly


of this type and form drag is reduced to a minimum, it is
important to get the best surface finish possible.
All handholes through the fabric and holes where controls,
et cetera, enter should be properly reinforced by inspection
rings or frames.
When covering a wing with fabric, it is common practice to
pass the fabric around the leading edge.
96

Metal covered wings. Metal covered wings should be free from


buckling or wrinkling of the metal covering.
Deflections or deforma
tions at low load factors which may result in fatigue failures also
should be avoided.
CONTROL SURFACES

DESIGN

a. Trailing edges of control surfaces should be as substantial as the


trailing edges of wings. They should hold their shape when sub
jected to fabric tension loads.
The covering of control surfaces should be provided with holes
drainage and "breathing."

6.

for

An improvement in control and reduction in drag can be accomp


lished by covering the gap between control surfaces. Thin metal or
c.

celluloid on the outside of the gap, or fabric inside, is frequently used


for this purpose. On some designs a circular leading edge on the
moving surface fits snugly into the other surface so that the resulting
small gap needs no other seal. Care should be taken that the gap
covers do not obstruct free drainage, or create undue friction, and that
interference cannot occur.
d. The stabilizer on experimental designs should be arranged so

that the incidence can be changed if necessary to obtain the proper


balance.

e. On wings which have no means of adjustment for twist, a small


metal tab fastened to the trailing edge of one aileron can be bent as
In extreme cases this may be
necessary to trim the wing laterally.
necessary on the rudder also.

/. If

the elevator is unusually low so that it drags in high grass, it


be advisable to cover it with the heavier Grade A fabric instead

may
of the light glider fabric.

g. The leading edge of wood fins and stabilizers usually is covered


with plywood to hold the airfoil contour. Spars may be built up or

solid.

ribs

Ribs are trussed as in wings unless the surface is thin, then


built with solid plywood webs.

are usually

i.

is

is

1/4

h. Wood tail ribs are trussed in the usual way with diagonals in
compression under normal flight. A minimum practical size for caps
and diagonals is about %6 by
When
inches, when using gussets.
the trussing
glued directly to the caps without gussets the material
must be wider and thinner to provide sufficient gluing area. All
joints should be made as concentric as practical.

It will

be found very convenient for construction purposes

to

design the wood wing ribs and aileron or flap ribs together so that the
two surfaces can be built up as unit with their respective spars in
place and parted after completion. This avoids tedious lining up and

independent jigging.

97

GOOD

POOR

PLYWOOD

POOR

GOOD

HINGE
Figure 3 I II.

Typical finings.

98

j.

Special care should be taken to provide sufficient strength to


carry concentrated loads from aileron and flap hinges into the main
A separate structure is usually not necessary to carry
structure.
these loads, but the ribs at these points should be somewhat oversize
with respect to the hinge reactions because of the redundancy be
tween aileron and wing structure. The control horn reactions in a
fore and aft direction also should be considered.
It is desirable to
have the control horn at a hinge so that the control load can be
reacted through the hinge without bending the beam in the control
surface.
This also eliminates undesirable flexibility in the control
system.
k. Control surface horns are generally constructed of plywood or
metal, preferably the latter. They should be attached to the control
surface spars near a hinge to avoid bending the spar, and in such a
manner as to distribute the loads into the spar without tending to
split it.
I. Aileron and flap surfaces, as well as tail surfaces, are designed to
carry the loads from the control horn either by adopting a torsiontube construction, or using diagonal ribs. The first method is carried
out by boxing in the leading edge of the surface with plywood, provid
ing cap strips at the corners of the box for gluing. In the latter
method, the surface ribs are laid out in a continuous zigzag truss from
the horn.
m. Long ailerons often have two control horns in order to provide
extra torsional stiffness and keep the surface from feeling "rubbery"

underload.

n. Although many high performance ships have continued to use


external control surface horns, it is believed that internal horns are a
worthwhile attempt to reduce drag.
Control surface stops. Stops are advisable for all control surfaces,
particularly adjustable stabilizers and elevator trailing edge tab
systems. For these, the stops should be positioned so as to limit the
travel to the approved range. In general, stops are advisable for all
surfaces in order to avoid interferences and possible damage to the
parts concerned, particularly in the case of large surfaces where the
deflections in the control system may permit the surface to exceed the
design range of travel. Stops should be installed at the control
systems in the cockpit and also at the control surfaces.
Hinges.
a. Hinges of the strap type bearing directly on torque tubes are
advisable only in the case of steel torque tubes which have a multiply
ing factor of safety as specified in Chap. 1. In other cases sleeves of
suitable material should be provided for bearing surfaces.
b. Clevis pins may be used as hinge pins provided that they are
made of suitable material and are properly locked.
c. The following points have been found of importance in connec

tion with hinges

99

1.

2.

Provisions for lubrication should be made if self-lubricated


or sealed bearings are not used.
The effects of deflection of the surfaces, such as in bending,
should be allowed for, particularly with respect to misalign
This may also influence spacing of the
ment of the hinges.
hinges.

3.

4.

is

it

is

is,

5.

Sufficient restraint should be provided in one or more brackets


to withstand forces parallel to the hinge center line. Rudders,
for instance, may be subjected to high vertical accelerations in
ground operation.
Hinges welded to elevator torque tubes or similar components
may prove difficult to align unless kept reasonably short and
welded in place in accurate jigs.
In
Piano type hinges are acceptable with certain restrictions.
the
general, only the "closed" type should be used, that
means.
hinge leaf should fold back under the attachment
The attachment should be made with some means other than
wood screws, and this attachment should be as close as possible
to the hinge line to reduce flexibility.
Piano hinges should
not be used at points of high loading, such as exist at control
Due
horns, unless the reaction
satisfactorily distributed.
worn hinge wire,
to the difficulty in inspecting or replacing
better to use several short lengths than one long hinge.

is

b.

is

is

is

Installation.
no
a. Movable tail surfaces should be so installed that there
when
one
interference between the surface or their bracing
any
held in its extreme position and any other
operated through its
full angular movement.
It very important that control surfaces have sufficient torsional
No specific limits of permissible maximum deflection of the
rigidity.
surface alone are offered, since these may vary widely with the type,
size and construction of the surface.
However, the behavior of the
surface during proof tests should be closely observed.
In addition
the effect of the control system "stretch" on the total surface deflection
under limit maneuvering loads should be considered from the stand
point of "surface usefulness."

d.

is

is

is

c. Clearances,
both linear and angular, should be sufficient to
prevent jamming due to deflections or to wedging by foreign objects,
common practice in the design stage
particularly safety pins. It
to incorporate an angular clearance of degrees beyond the full travel
limit.
Surfaces and their bracing should have sufficient ground
clearance to avoid damage in operation, or when one wing tip
rest
ing on the ground.
External wire bracing on tails
subject to vibration and the
of
the
wire
and
end
connections
should be such as to
assembly
design

100

withstand this condition. Leading edges and struts should have


adequate strength to withstand handling loads if handles or grips are
not provided.
e. Direct welding of control horns to torque tubes (without the use
of a sleeve) should be done only when a large excess of strength is
indicated.
Elevators.
a. When separate elevators are installed they should be rigidly
interconnected.
b. When dihedral is incorporated in the horizontal tail the universal
connection between the elevator sections should be rugged and free
from play.
Tabs.
a. Control surface trailing-edge tabs should be statically balanced
about their hinge lines, unless an irreversible nonflexible tab control
system is used. The installation should be such as to prevent develop
ment of any free motion of the tab.
6. If trailing-edge tabs are installed, care should be taken in propor
tioning areas and relative movements so that the main surface is not
aerodynamically overbalanced at any time.
c. Minimum deflections and play are of primary importance in
the installation of tabs. Strength of the surface and anchorages
should be sufficient to prevent damage or misalignment from handling,
particularly thin sheet tabs which are set by bending to the proper
position.
CONTROL SYSTEMS DESIGN

Rigidity. It is

that control systems, when subjected


to limit load and operation tests, indicate no signs of excessive deflec
tion or permanent set. In order to insure that the surfaces to which
the control system attaches will retain their effectiveness in flight, the
deflection in the system should be restricted to a reasonable limit.
As a guide for conventional control systems, the average angular
deflection of the surface, when both the control system and surface are
subjected to limit loads as computed for the maneuvering condition
neglecting the minimum limit control force but including tab effects,
should not exceed approximately one-half of the angular throw from
neutral to the extreme position.
b. Dual controls. Dual control systems should be checked for the
This may be critical
effects of opposite loads on the wheel or stick.
for some members such as aileron bell crank mountings as an "open"
no return except through the balance cable between
system, that
In addition, the deflections resulting from this long load
the ailerons.
path may slack off the direct connection sufficiently to cause jamming
of cables or chains unless smooth close-fitting guards and fair leads
essential

is,

a.

are used.

101

Control system locks. When a device is provided for locking a


control surface while the aircraft is on the ground or water, compli
c.

ance with the following requirements should be shown :


1. The locking device should be so installed as to positively pre

2.

vent taxiing or taking off, either intentionally or inadvertently,


while the lock is engaged.
Means should be provided to preclude the possibility of the
lock becoming engaged during nights.

Installation.
The predominating type of cockpit controls is the stick and pedal
Wheel control is sometimes used for high performance
system.
gliders with restricted cockpit size.
a. Travel. It is suggested that the total travel at the top of the
stick should be approximately 12 inches or more in both planes to
avoid undue sensitivity of the elevators and provide sufficient leverage
on the aileron. When a wheel control is used the angular motion
should be not less than 60 degrees either side of neutral.
Rudder
pedals should have at least 2 inches travel either way.
b. Positioning. In the layout and positioning of a control con
sideration should be given to its relative importance and to its con
venient placement for the usual sequence of operations. Thus for
landing, it is desirable that flap control and brakes be operable without
Likewise, secondary controls
changing hands on the wheel or stick.
should be so located that the possibility of accidental or mistaken
operation is remote.
c. Centering. A point sometimes overlooked is the effect of the
weight of a control member or of a pilot's arm or leg on the centering
characteristics of the control.

All control

Stops.

systems should be provided with stops that posi


limit
the
tively
Stops
range of motion of the control surfaces.
a.

should be capable of withstanding the loads corresponding to the


design conditions for the control system.
6. Although the location of stops within the control system is not
specified, they should preferably be located close to the operating
force in order to avoid a "springy" control. Additional stops also
should be installed at the surfaces.
Stops should be adjustable where
production tolerances are such as to result in appreciable variation in
range of motion.
Hinges, bearings, and joints.
a. Hinges. Control surface hinges of aircraft standard normally
In general, hinge pins should be
are available at the supply houses.
in
or
more
diameter.
If
clevis
inch
pins are used, a washer should
%
Standard A-N bolts or clevis bolts
be placed under the cotter pin.
are preferable to clevis pins in the rotating joints of hinges or controls.
102

b. Bearings. Bearings should be arranged so that they can be


readily inspected and lubricated.
c. Friction. Excessive friction should be especially avoided in the
aileron control systems of large high performance gliders. This may
sometimes dictate the use of special anti-friction bearings at heavily
loaded pivots.
d. Locking devices. Bolts, straight pins, taper pins, studs, and other
fastening means should be secured with approved locking devices.
The assembly of universal, and ball and socket joints should be in
sured by positive locking means, rather than by springs.
Woodruff
keys should not be used in tubing unless provision is made against the
key dropping through an oversize or worn seat.
e. Cockpit controls. Stick pivots and other similar joints in the
control system that tend to wear rapidly should be constructed with
a spacer tube on the through bolt to take the wear in the bearing
and allow the bolt to be clamped down tight. See fig. 3-IV.
Cables, pulleys and fairleads.
a. Cables. Control cables should be of the 6 x 19 or 7 x 19 extraflexible type, except that 6 x 7 or 7 x 7 flexible cable is acceptable in
the %2 inch diameter size and smaller. For properties see table
The 7x7 construction is found satisfactory
8.212 of MIL-HDBK-5.
where slight cable bends around pulleys of only 30 or less are en
Cable and splices should be made by an approved tuck
countered.
method such as that of the Army and Navy, except that standard
served and soldered splices are acceptable for cables not over %2 inch
in diameter. However, cables of other sizes with served and soldered
fastenings will be satisfactory provided they are not stressed above
50 percent of their rated strength. Approved swaged type terminals
Dimensions for approved splices are given in
are also acceptable.
fig 3-V. It should be noted that cable sizes are governed by deflec
tion conditions as well as by strength requirements, particularly when
a long cable is used. Some acceptable types of cable joints are given

in

fig. 3-VI.
b. Turnbuckles.

Turnbuckles should

be located so as to be accessi

ble for adjustment and preferably not in the center of long unsup
ported spans where they can slap around too freely. Examples of
turnbuckle installations are given in fig. 3-VII.
c. Spring connecting links. Spring type connecting links for chains
have not been found to be entirely satisfactory in service. It is
advisable that a more reliable means, such as peening or cotter pins,

be employed.
d. Fairleads. Fairleads of non-metalic material, such as the phen
olic plastic compounds, should be used to prevent cables, chains and
links from chafing or slapping against parts of the glider, but should
not be used to replace pulleys as a direction-changing means. How
ever, where the cable load is small, and the location is open to easy
103

visual inspection, direction changes (through fairleads) not exceeding


A somewhat greater
3 are satisfactory in primary control systems.
value may be used in secondary control systems.

Pulleys. Standard pulleys of the A-N type usually are lighter


than metal pulleys. Pulleys that carry a 180-degree wire bend should
be carefully mounted so that there is no danger of their leaning over
e.

They should also line up accurately with


the plane of the cables or the flanges will wear out quickly.
See
and binding under load.

fig.

3-VIII.

located that

jam it.

All pulleys should

be provided with annular guards so

slack wire cannot get off the pulley in any manner and

ADJUSTABLE, FORE AND AFT, BY PILOT

Figure 3 IV. Adjustable elevator bung**, control system details.

104

(a)

SERVED AND

( b

TUCK SPLICE

DIMENSIONS

AFTER STRETCHING

n/2 :/8

2 1/16

3/32

9/16

!?/8

15/8

:$/8

3/16

:?/2

5/8

t/2

1/16

:?/2

5/32

H/16

Figure 3-V.

!/8

2
2

:?/8

1/8

3/8

+0
- 3/8

!/8

Standard cable splice ends.

105

?/2

-1/8

9/'6

1/16

DIA. OF CABLE

SPLICE

SOLDERED

106

(3)

(4)

GOOD

GOOD

HEXAGONAL
CLEVIS
Figure 3VII. Turnbuckle installations.

107

BOLT

OR

Figure 3VIII.

ConfroZ-pulley

108

brackets.

Motions and clearances.

Tension changes. The movements of horns, cables and other


components with respect to each other should be such that there is
Eleva
no excessive change in system tension throughout the range.
tors mounted on adjustable stabilizers, in particular, should be
checked for this possibility.
Pulley guards should be close fitting
to prevent jamming from slack cables since wide temperature varia
tions may cause rigging loads to vary appreciably.
b. Aerodynamic balancing. When using extreme values of differ
ential motion in the aileron control system or a high degree of aero
dynamic balance of the ailerons, the friction in the system must be
kept low; otherwise the ailerons will not return to neutral and the
This is
lateral stability characteristics will be adversely affected.
particularly true when the ailerons are depressed as part of a flap
system, in which case there may even be definite over-balance effects.
c. Creeping. Adjustable stabilizer controls should be free from
When adjustment is secured by means of a
"creeping" tendencies.
screw or worm, the lead angle should not exceed 4 degrees unless addi
tional friction, a detent, or equivalent means is used. In general,
some forms of irreversible mechanism should be incorporated in the
system, particularly if the stabilizer is hinged near the trailing edge.
d. Interference. Proper precautions should be taken with respect
to control systems to eliminate the possibility of jamming, interfer
ence from cargo, passengers or loose objects, and chafing or slapping
of cables against parts of the glider. All pulleys should be provided
with satisfactory guards. A control column or stick located between
a pilot and a passenger should not be used unless a throwover type
of wheel control is incorporated. The cockpit controls should be
protected by a flexible boot or similar means, if necessary, to preclude
any possibility of any objects becoming fouled in the air controls.
e. Clearance. At the control surfaces themselves ample clearances
(5) should be left beyond the normal deflections, to prevent inter
ferences and possible damage when the surface is slammed over by
wind on the ground.
f . Nose wheel. It is essential when a nose wheel steering system is
interconnected with the flight controls that care be taken to prevent
excessive loads from the nose wheel over-stressing the flight control
system. This objective may be attained by springs, a weak link, or
equivalent means incorporated in the nose wheel portion of the control
system.
Single cable controls. Single cable controls refer to those systems
which do not have a positive return for the surface or device being
In general, service experience shows that their use has
controlled.
been satisfactory.
Rudder control systems without a balance cable
at the pedals are considered satisfactory if some means such as a
a.

109

spring is used to maintain cable tension and to hold the pedals in the
proper position. If should be noted that it is not the intent of the
specified requirement to require a duplication of cables performing
the same function.
Spring devices. The use of springs in the control system either as a
return mechanism or as an auxiliary mechanism for assisting the pilot
(bungee device) is discouraged except under the following conditions :
a. The glider should be satisfactorily maneuverable and controllable
and free from nutter under all conditions with and without the use of
the spring device.
b. In all cases the spring mechanism should be of a type and design
which can be demonstrated to be satisfactory by actual flight tests.
c. Rubber cord should not be used for this purpose.

Flap controls.

The flap operating mechanism should be such as to prevent


sudden inadvertent or automatic opening of the flap at speeds above
the design speed for the extended flap conditions.
Means should be
provided to retain flaps in their fully retracted position and to in"
dicate such position to the pilot.
a.

Undesirable flight characteristics, such as loss of lift and conse


quent settling, may result from too rapid operation of flaps which
give appreciable lift. When the prime function of the flap is to act
as a brake, however, slow operation is not so important.
When
flaps extend over a large portion of the span, the control and means of
interconnection should be such as to insure that the flaps on both
sides function simultaneously.
b.

Tab controls.

a.

Position indicator. When adjustable elevator tabs are used for

the purpose of trimming the glider, a tab position indicator should


be installed and means should be provided for indicating to the pilot

of adjustment suitable for safe takeoff and the directions of


motion of the control for nose-up and nose-down motions of the glider.
a range

Reversibility. Tab controls should be irreversible and nonflexible, unless the tab is statically balanced about its hinge line.
b.

Wear and vibration. In addition the the air loads, consideration


should be given in the design to the lapping effect of dust and grease
on fine threads, deflections of the tab due to the small effective arm
of the horn or equivalent member, and vibration common to the trail
ing edge portion of most movable surfaces.
c.

Degree of travel. It is advisable to avoid a tab control with small


travel because of the resulting abrupt action of the tab.
d.

Direction of operation. Proper precautions should be taken


against the possibility of inadvertent or abrupt tab operation and
operation in the wrong direction.
a.

110

LANDING GEAR DESIGN

a. It is undesirable and unnecessary to mount wheels on an external


landing gear structure as is done on power planes for ground clearance.
One landing wheel located near the center of gravity (preferably aft)
supplemented by a nose skid and either a tail skid or a skid directly
aft of the wheel is customary. Some designs dispense entirely with
the wheel, and use skids only.
b. A tail-skid may be desirable on some designs to protect the bot
tom of the fuselage and rudder. If the skid takes much shock on
takeoff or landing, the spring leaf type is desirable.
Landing skids.
a. Main skids. Landing skids of ash or similar material are used
on most gliders to take and distribute nose-down landing loads.
Skids must be sprung by rubber blocking or other means when pneu
matic wheels are not provided to absorb the major part of the shock.
Even with wheels, the skid is often sprung.
"rubber doughnuts"
b. Shock absorption for skids. Whether
blocks, tennis balls, or other springing is supplied, there should be
two or more points of support besides the front anchorage, capable
of taking side as well as direct vertical length into the fuselage by
means of a flexible boot.
c. Skid design. Skids should be reasonably easy to replace especi
ally on gliders not provided with a wheel. A minimum size of Y2 x 2
inches is recommended.
For use on coarse-surfaced
airports, a
metal-faced skid should be used.

MAIN GEAR

The wheels of the main landing gear are most satisfactory for all
varieties of operations if located close underneath the average CG
of the glider. This enables the pilot to hold the tail either high or
When braking, the nose bears on the ground
low as may be desired.
and helps to slow the glider down as well as to kill the lift on the wings.
The attitude of the glider when held over on the nose should not allow
the tail to rise higher than necessary to kill most of the wing lift, as
it would turn over more easily in a tail wind.
Shock absorption.

a. The wheel should be located so as to project enough below the


forward skid so that practically full tire deflection is available at a
More than this amount is undesirable
speed slightly above the stall.
if the skid is to protect the tire from rough obstructions.
b. When using a small wheel, with limited tire deflection for shock
absorption, it is desirable to spring the skid. Large wheels can take
all the loads.
Wheels and tires need not be of special glider type,
unless a wheel or tire failure will prove dangerous to the particular
glider in question.

657822 O - 62 - 9

Ill

e. Regardless of the type or extent of the shock absorbing qualities


of the glider, it is advisable, from service considerations, to design a
weak and easily replaceable part into the system, the partial failure
Such
of which will not damage the remaining landing gear structure.
procedure will prevent unduly high stresses from being transmitted
to the main fuselage or wing structure, and will greatly simplify
repairs.
Wheel support structure. The wheel support structure should be
Otherwise
kept as independent as possible of the lift truss system.
an incipient or unnoticed failure in the wheel or attachment from a
bad landing might cause a failure of the lift truss system in flight.
Brakes. Brakes on landing wheels are necessary to give control
over the landing run, such as when landing down wind or down hill.
Glider type brakes built into the wheel are available on some size
wheels which might be suitable for the heavy two-seaters. For
smaller and lighter wheels, a simple brake consisting of a shoe of metal
or composition materials pressed down on the circumference of the
A control wire is carried forward from the brake
tire is satisfactory.
to a handle in the pilot's cockpit.
Dual wheels. Although not as common, landing wheels are some
times used in pairs. If spaced so that the CG of the glider cannot
fall outside of the wheel base, the glider will not lie on the wing tip
as with a single wheel.

Purpose. The

FUSELAGE DESIGN

fuselage is designed to carry the pilot, support


surfaces
and
the tail
landing gear with as little weight and drag as is
consistent with the general purpose of the glider.
a.

The

nose of the fuselage should be made sufficiently


strong to give the pilot reasonable protection in case of a crash, as well
as carry the launching and towing loads from the towing hook.
c. Landing gear. The landing wheel and skid, if any, should be
well supported structurally.
The former should be boxed around
mud
or
sand
cannot
so that snow,
pack into the interior of the fuselage.
d. Ground angle and clearance. The bottom of the fuselage aft
of the wheel should provide sufficient ground angle and clearance so
that the wing can be held at a high enough angle of attack for takeoff
An angle on the wing of at least 10 or 12 degrees is
and landing.
advisable, part of which can be provided by setting the wing at an
angle of incidence on the fuselage.
e. Tail skid. The tail end should be provided with a skid or so
arranged that the bottom of the rudder is protected from obstructions
when landing.
f. Provisions for turn-over. The fuselage and cabins should be
designed to protect the passengers and crew in the event of a complete
turnover and adequate provision should be made to permit egress of
passengers and crew in such event.
b. Nose.

112

Pilot and passenger compartments.

a. Ventilation and visibility. The pilots compartment should be


so constructed as to afford suitable ventilation and adequate vision

to the pilot under normal flying conditions.

In cabin gliders

the

windows should be so arranged that they may be readily cleaned or


easily opened in flight to provide forward vision for the pilot.
b. Seats. Seats for passengers should be securely fastened in place
in both open and closed gliders, whether or not the safety belt load
is transmitted through the seat. (See the applicable TSO for safety
belt requirements.) Consideration should be given in the seat
installation, to the fact that under some types of operations para
chutes will be required. Provisions therefor should be made for
Shoulder harness may also be necessary in certain
parachutes.
operations.
c. Pilot and passenger enclosures. Removable "scoops" around the
pilot should be securely attached to carry the air loads encountered at
the maximum gliding speed, but must be easy to release and push off'
in case the pilot has to bail out. They should be so designed that their
removal in flight at high speeds will not injure or inconvenience the
pilot or passengers, or block the exits. The nose may be built up
around the pilot and only a local portion be removable. Sufficient
room should be provided for exit wearing the type parachute for which
the seat is designed. A clear fore and aft opening of not less than 24
The above recommendations also apply to the
inches is desirable.
hinged, sliding or removable canopy types of enclosures.
Steel tube fuselages.
a. General.- Steel fuselages are built up by welding round or square
tubing into a rigid truss structure. Sections through the fuselage

are usually combinations of rectangular, triangular, and diamond


shape. The basic shape is extended up to carry the wing and down
for the wheel and landing skid. The portion forward of the wing is
frequently cantilevered out under the pilot, the top and side fairing
being removable as a whole for exit.
b. Load distribution. Loads from the pilot's seat, belt, wing, and
strut attachments, wheel and tail surfaces should be properly dis
tributed into the fuselage trussing. Eccentricities and bending of the
truss members should be avoided wherever possible.
Usually, the
stress analysis can be simplified by elimination of redundant members.
c. Diagonal braces. Diagonal braces are necessary for stability
in rectangular or diamond shaped bulkheads having unsymmetrical
loads applied on them. Where one side of a rectangular truss is
broken, as for a cockpit opening, the adjacent bulkheads usually
require a diagonal to carry the shear around the open rectangle.
This
is not necessary when an extra over or under truss serves the same
Many gliders have an extra bottom "V" structure which
purpose.
serves to support the skid and wheel under the main structure. It is
113

not necessary that all the bulkheads in a rectangular fuselage have a


diagonal, but an occasional diagonal between the tail and rear wing
attachment bulkhead will increase the torsional rigidity and provide
means for transferring the load if a member is damaged.
d. Joints. Wherever, possible joints should be designed for sim
plicity. Wherever possible, not over six members should intersect at
a joint. This is to reduce the likelihood of strain cracks after welding.
Joints must not be butted square unless there is no possibility of
tension or bending in the member.
On members designed for tension
rather than for column loads, it is beneficial to make the end joints at
a flat angle to the tube axis so as to develop the full tensile capacity of
the member.
the
e. Splices. Splices in tubing should be made by telescoping,
to
tube
cut
at
an
at
an
of
20
30
outer
being
angle or by butting
angle
degrees to the tube axis and supporting with an inserted sleeve.
External sleeves may also be used. All welds should be at an angle
rather than straight around the tube, unless the member is loaded in
pure torsion only.
f. Fairing. Truss fuselages can be faired out for better shape
which results in lower aerodynamic drag.
Strips of wood, tubing,
These members
or aluminum alloy sections are used for this purpose.
should be strong enough to resist the fabric tension and handling loads.
The fairing strips are supported by clips on the structure or plywood
formers built out from the bulkheads.
Plywood monocoque fuselages.
a. General. Plywood monocoque fuselages are either of simplified
type with fiat faces, or of full curved form. The latter type has the
The simple type is built up on four
best aerodynamic efficiency.
main longerons with flat sides. The top "deck" is flat, round, or
"V" shaped, faired down to the tail from the neck carrying the wing.
The bottom surface is carried down in "V" shape to support the keel
son above the landing skid.
Pneumatic wheels are carried between
main fuselage bulkheads, and recessed up into the fuselage body.
Since the skids are usually sprung on rubber or other means for shock
absorption, heavier bulkheads are provided locally to carry the loads
into the main fuselage shell.
b. Plywood sizes. In general, the lightest practical sizes of ply
wood will be thick enough to carry the design shear loads in the side
Diagonals may be
panels so that diagonals will not be required.
needed at panels where the external loads are high as between the
main wing bulkheads, and in the pilot's bay. A minimum thickness
of 1 mm. for birch and %4 inch for spruce or mahogany is recommended
for fuselage covering.
c. Bulkheads. The bulkheads in this type of fuselage can be made
of straight struts fastened at the corners by blocking notched for the
longerons and gusseted with plywood.
114

Curved monocoque type. The curved monocoque type of construc


tion necessitates laying the plywood on in smaller panels where there is
compound curvature. Longitudinal plywood seams should be sup
d.

ported by light internal stiff eners. These may run through the bulk
heads and serve also as longerons, or be laid only in between as local
The rear part of curved fuselages is often
(intercostal) stiffeners.
made straight conical with oval sections so that there is curvature in
only one plane. The plywood then may be laid in long lengthwise
panels.
e. Rigidity.- Care should be taken that the minimum section just
forward of the fin attachment is not so small as to be too flexible
under torsional loads from the vertical tail surfaces, causing flutter
in rough air or at high speed. This precaution also applies to all
kinds of fuselages in which the rear part is necked down to form a long
thin "boom."
In such cases the stiffness in bending about both axes
is important.
No definite limits for rigidity can be set down; how
ever, the natural periods of vibration in torsion and both bending
directions should all be of different periods to prevent interaction.
These vibration rates can be measured on the ground by vibration
tests conducted with the glider on the ground.
f . Concentrated loads. The loads from main fittings should be well
distributed to the bulkheads by means of suitable blocking. Birch
plywood or ash pads should be provided under fittings. Wood corner
blocks which carry shear through the glue joint should be laminated
pie-fashion if necessary to avoid gluing at an angle of more than 30
Butt glue joints on end grain will not
degrees off the grain direction.
carry shear or tension loads. For various methods of installing
corner blocks, see fig. 3-IX.
Crash protection.
a. General. The fuselage should be designed to give reasonable
assurance that each occupant provided with the proper belts and
harness will not suffer serious injury during minor crash conditions as
a result of contact of any vulnerable part of his body with any pene
trating or relatively solid object.
If the characteristics of the glider make a turnover reasonably
probable, the fuselage, in combination with other portions of the
structure, should be designed to afford protection of the occupants in
a complete turnover.

Compliance Suggestion
PERSONNEL

COMPARTMENT

Relatively rigid structural members

or rigid mounted items of


equipment which might be struck by the head, arm, knees, et cetera,
should be padded.
Padding preferably should be of foam polystryrene or unicellular polyvinal chloride material rather than ordin
ary foam or sponge rubber, which are ineffective. Heavy transversal
115

(b)

FOOTING ON BUTTED
STRUTS - COMPRESSION

Figure 3 IX. Installation of corner blocks.

or other structure behind a light weight instrument panel


should be positioned several inches behind the ductile skirt of the
instrument panel.
The backs of forward positioned seats in tandem
gliders, often bearing solid tubing members in the backrest, should
be designed to pivot forward so that the occupant in the rear seat
braces

116

would not contact the solid member due to the body pivoting about
There should be a similar clearance for the front occu
the seatbelt.
Instrument
panels should be smooth, with top edge curved in
pant.
It is preferred that openings for instruments
a substantial radius.
should have beveled instead of sharp edges. Also, seats should be
adequate to withstand downward loads without failure of the seat
or injury to the pilot.
Control wheels and control sticks should be
free of sharp edges, hooks or projections which might cause injury in
a minor accident.

Compliance Suggestion
NOSE STRUCTURE

As far

practicable, the nose structure ahead of the cockpit should


be designed to progressively collapse from the extreme nose towards
The structure should be progressively
the rear, upon head-on impact.
Such shock absorption
stronger from the nose towards the rear.
minimizes the effects of sudden deceleration encountered in a head-on
impact.
as

TOW CABLE RELEASE MECHANISMS

Operation tests on cable release mechanisms are covered in Chap. 2.


Also, Chap. 1 covers limit loads to be applied to the operating handle.
Releases should be designed to accommodate towline rings having a
minimum diameter of 1^ inches except in cases of special design.
The following precautions should be observed :
a. It should be impossible for bolts, lugs, or other projections on the
mechanism itself, or the structure surrounding the mechanism, to
foul the towline or towline parachute under any conditions. If a
special fitting is supplied to carry the parachute, it should be so
located that the parachute cannot become entangled on the lift
struts or wires.
The forward end of the nose skid should be so con
as
structed
to prohibit fouling between it and the towline and/or
parachute.
b. The operating handle in the cockpit
should be so located,
designed, and placarded that it cannot be confused with the spoiler,
brake or other control handles.
c. Cables or wires used to operate the release should be protected
from wear and abrasion due to normal operation, and from possible
When
damage caused by occupants in entering or leaving the glider.
fixed or flexible tubing is used for cable or wire guides, there should be
sufficient protection and drainage to prevent the formation of ice
inside the tube.

117

Chapter

4 EQUIPMENT

The equipment installed should be consistent with the type of


The requirements speci
operation for which certification is sought.
Addi
fied in this section are basic equipment recommendations.
tional equipment should be installed for special cases if necessary or
if specified in other sections of the Civil Air Regulations, such as
CAR, Part 43 for instrument requirements.
Each item of equipment specified for gliders should be of satisfactory
It should be properly installed and should function
type and design.
Items of equipment for which approval is required
satisfactorily.
should have been certificated in accordance with the provisions of
previous regulations, or they should show compliance with pertinent
Technical Standard Orders.

INSTRUMENTS AND EQUIPMENT


The following equipment for gliders with Standard Airworthiness
Certificates should be installed for the particular category of operation
specified. (For required instruments refer to Section 43.30 of CAR

Part 43.)
a.

Contact (day) flight rules.


1.

2.
3.
4.

Instruments listed in

CAR

43.30 (a), as applicable.

Approved safety belts for passengers and pilot (s).


Log-book.
Such instructions should be in the
Rigging instructions.
form of a sketch, or listed data, and should include sufficient
information to facilitate proper rigging of wings, control
systems, et cetera.

Note. Items 3 and 4 need not be carried in the glider.

b. Contact (night) flight rules.


1.

2.
3.
4.
5.

Equipment specified in paragraph a, above, and instruments


listed in CAR 43.30 (b) as applicable.
Forward and rear position lights.
Adequate source and supply of electrical energy for the instru
ments, electrical and radio equipment installed.
suitable dimming means.
fuses are used, one spare of each rating should be carried.

Instrument lights, incorporating

If

119

c.

Instrument flight.
1. Equipment specified in paragraphs a and b of above except
item b, 2, and instruments listed in CAR 43.30 (c) as ap
plicable.
2. Two-way radio communications system appropriate to the
available ground facilities.
3. Generator or battery of adequate capacity for powered gliders ;
battery or air pressure system for nonpowered gliders.

INSTALLATION

RECOMMENDATIONS

The following recommendations apply to the installation of specific


items of equipment:

INSTRUMENTS
The following recommendations are considered applicable to the
installation of instruments when such instruments are required for
particular operations.
Airspeed indicator. This instrument should be so installed as to
indicate true airspeed at sea level with maximum practicable accuracy,
but in no event should the instrument error be more than plus or
minus 5 miles per hour at speeds between the auto-winch tow placard
speed and the maximum certified speed.
Magnetic compass. This instrument should be compensated so that
the deviation in level flight does not exceed 10 degrees on any heading.
A suitable calibration placard should be provided and should be
located where it is not seriously affected by electrical disturbances
and magnetic influences.
Flight and navigation instruments. Flight and navigation instru
ments for use by the pilot should be so installed as to be easily visible
to him with the minimum practicable deviation for his normal posi
tion and line of vision when he is looking out and forward along the
flight path.
Gyroscopic instruments. All gyroscopic instruments installed in
gliders intended for operation under instrument flight rules should
derive their energy from a power source of sufficient capacity to
maintain their required accuracy in accordance with the manufac
turers' recommendations.
Safety equipment installation Safety belts. Safety belts should be
so attached that no part of the anchorage will fair at a load lower than
that corresponding with the ultimate load factors equal to those
specified in Chap. 1, multiplied, by a factor of 1.33.

EQUIPMENT INSTALLATION
Electrical equipment, if installed, should be free from hazards in
ELECTRICAL

in their method of operation and in their effects on other


parts of the glider. Items of equipment which are essential to the
themselves,

120

safe operation of the glider should be designed and installed to insure


that they will perform their intended functions reliably during all
reasonably foreseeable operating conditions.
batteries should be
Storage
battery. The capacity of storage
sufficient to supply all connected loads in probable combinations and

for probable durations. If corrosive electrolyte can be spilled during


flight or during servicing, means should be provided to prevent hazard

ous corrosive effects on adjacent glider structure or equipment.


Master switch. If electrical equipment is installed, a master switch
should be provided which will disconnect the storage battery from all
loads at a point adjacent to the battery.
Circuit protective devices. Protective devices (fuses or circuit

breakers) should be installed in the circuits to all electrical equipment.


Protective devices in circuits essential to safety in flight should be
accessible and identified so that they may be reset (or replaced, in
the case of fuses) during flight. Sufficient spare fuses should be
Circuit breakers should be of the tipprovided for this purpose.
free type.
Instrument lights. Instrument lights, when required, should pro
vide sufficient illumination to make all instruments and controls
The lights should be installed in such manner that
easily readable.
direct rays or bright reflections are shielded from the pilot's eyes.
Position and anti-collision lights. Position lights and anti-collision
lights, when required, should conform to the standards in CAR
3.700 to 3.705.

MISCELLANEOUS

Seats. Seats or

EQUIPMENT

INSTALLATION

chairs, even though adjustable, should be securely


fastened in place, whether or not the safety belt load is transmitted
through the seat.

121

Chapter

5 FLIGHT CHARACTERISTICS

The following recommendations are for gliders for which a type


The glider should meet the
inspection authorization has been issued.
recommendations set forth below under all critical combinations of
weight and center-of-gravity positions within the range of each for
which certification is sought.
Controllability. It should be possible, under all conditions of
operation probable for the type, to make a smooth transition from
one flight condition to another, including turns and slips without
requiring an exceptional degree of skill, alertness or strength on the
part of the pilot and without danger of exceeding the limit load factor.
Trim. The means used for trimming should be such that after
being trimmed and without further pressure upon, or movement of,
either the primary control or its corresponding trim control, the glider
will maintain (1) lateral and directional trim in unaccelerated forward
flight at the speed for minimum sink, (2) longitudinal trim within a
speed range from 1.1 V, to 1.6 V,.
Stability. The glider should be longitudinally, directionally and
laterally stable when trimmed within the speed range specified above.
Suitable stability and control "feel" (static stability) should be
required in other conditions normally encountered in service if flight
When
tests show such stability to be necessary for safe operation.
trimmed, as indicated in the previous paragraph the characteristics
of the control forces and the friction within the control system should
be such that :
a. A pull on the longitudinal control should be required to obtain
and maintain speeds below the specified trim speed and a push re
quired to obtain and maintain speeds above the specified trim speed.
This should be set at any speed which can be obtained without exces
sive control force except that such speeds need not be greater than the
appropriate maximum permissible speed or less than the minimum
speed in steady and stall flight.
b. The airspeed should return to within 10 percent or 5 m.p.h. of
the original trim speed, whichever is greater, when the control force
is slowly released from any speed within the limits defined in para
graph a, above.
c. Any short period oscillations occurring between stalling speed
and maximum permissible speed should be heavily damped when
primary controls are (1) free, and (2) in a fixed position.
123

the aileron and rudder control


d. In straight steady sideslips
movement and force increase steadily, but not necessarily in constant
At greater angles
proportions, as the angle of sideslip is increased.
of sideslip up to that at which full rudder-control is employed, the
rudder pedal forces should not reverse.

Compliance Suggestion
STABILITY

AND CONTROL SPEEDS

Although
Stability will be measured in the free-control condition.
stability and trim are closely connected, they should not be confused.
If forces are present
A nose-heavy glider is not necessarily unstable.
which tend to make the glider assume some speed at which it is
If it actually attains this speed
balanced it will be statically stable.
and ceases to oscillate, it is both dynamically and statically stable.
If the craft is stable but extremely nose heavy the speed at which
it will cease to oscillate in the free control condition may be higher
than the placard gliding speed, or the oscillations involved may
result in a speed higher than the placard speed.
Normal flight conditions as used herein refer to normal maneuvers
and speeds between V, and VD (placard).
Stalls. Stall demonstrations should be conducted by reducing the
speed at approximately one m.p.h. per sec. until a stall results as
evidenced by an uncontrollable downward pitching motion of the
It should
glider, or, until the longitudinal control reaches the stop.
be possible to prevent more than 15 roll or yaw by normal use of the
controls during recovery, and there should be no uncontrollable
tendency for the glider to spin.
When stalled during a coordinated 30 banked turn it should be
possible to recover to normal level flight without encountering an
excessive loss of altitude, uncontrollable rolling characteristics or
uncontrollable spinning tendencies.
Spins. Spin demonstrations should include recovery from three
turn spins conducted with (1) controls held in the position normal for
spins; (2) with controls crossed; and (3) with ailerons applied in the
direction of rotation.
It should be possible to recover from such
spins in not more than one turn by applying the controls in a manner
normal for recovery and without exceeding either the limiting air
speed or the limiting positive maneuvering load factor for the glider.
It should not be possible to obtain uncontrollable spins by any possible
use or position of the controls.

Compliance Suggestion
SPIN

CHARACTERISTICS

a. In some cases, gliders are designed purposely with the ability


to spin, since this would offer a means of making a safe exit from
turbulence ; however, the use of dive brakes or spoilers may eliminate
the necessity for such a maneuver.
124

Gliders should have good control below the stall speed. There
should be no tendency to fall off to one side after an accidental stall
in straight flight. If such tendency exists, it should be possible to
prevent it by normal use of the controls.
c. Gliders that will not spin may fall into a spiral dive.
Since the
speed in this maneuver is not limited as it is in the spin, the results
may be serious. High performance gliders, due to their clean design,
may build up dangerous speeds in spiral dives with great rapidity.
Hence, there should be adequate control to recover from this condi
tion, as well as to prevent it.
Ground handling characteristics. All gliders should be readily
controllable during takeoffs with all launching methods approved for
the type. There should be no uncontrollable ground looping or
porpoising tendency during landing.
Flutter and vibration. All parts of the glider should be demonstrated
to be free from nutter and excessive vibration at all speeds up to at
least the minimum value of VD permitted for which compliance with
structural loading requirement has been proved.
6.

Compliance Suggestion

Tail buffeting at

TAIL

BUFFETING

speeds close to the stall or in turns in the low


not be considered objectionable, provided that it

speed range will


does not occur regularly at speeds normally used, and further pro
vided that its magnitude is small and not detrimental.

FLIGHT TESTS
Compliance with the foregoing flight recommendations should be
demonstrated by means of suitable flight test of the glider.
Test pilot qualifications. The applicant should provide a person
holding an appropriate airman certificate to make the flight test,
but the FAA representative may pilot the glider during such parts of
the tests as he may deem advisable.
Parachutes. Parachutes should be worn by members of the flight
test crew when deemed necessary by the FAA representative.
Instrument calibration. The applicant should submit a report
overing all the computations and tests required in connection with
calibration of flight instruments. The FAA representative will
conduct any tests which appear to him to be necessary in order to
check the calibration report or to determine the airworthiness of the
glider.

Compliance Suggestion

In

INSTRUMENT

CALIBRATION

the average glider flight test, the only instrument that must be
It must be possible
accurately calibrated is the airspeed indicator.
125

to accurately determine

the readings at the placard VD, Vuw, V,f and

V,.
Loading conditions. The loading conditions used in flight tests
should be such as to cover a normally expected range of loads and CG
positions, and will be those for which the glider will be certified.

Compliance Suggestion
TEST

CONDITIONS

a.

In flight testing two-place

6.

In

the weight of the passenger


and equipment should be simulated by ballast such that the normal
loading conditions are represented as closely as possible.
cases where

extreme aft

gliders,

the pilot is too heavy to make flight tests at

CG positions, such as might be encountered in a single-

place ship with a light pilot, dumpable ballast may be added to the
Since this
tail, provided the allowable gross weight is not exceeded.

procedure may cause the glider to enter a flat spin, extreme caution
should be observed.
c. Tests will be considered unsatisfactory if tail heaviness or un
favorable spinning characteristics are evident. Tests should include
CG positions resulting from the following loading conditions:
1.

Single-place

rearmost position.

gliders.

Pilot weight

100

lbs., all equipment

in

Two-place gliders. 100-lb. person in front seat, 220-lb. person


in rear seat and all equipment in rearmost position.
(It is assumed
that the rear seat is aft of the eg.)
2.

side-by-side gliders. Same as 1, except that the CG


position should be satisfactory with a 100-lb. pilot and a 100-lb.
If the above condi
passenger without the use of removable ballast.
3.

Two-place

tions cannot be met, the glider should be placarded to prevent an


unfavorable combination of pilot and passenger weights.
Ballast. Ballast may be used to comply with performance recom
mendations for longitudinal stability and balance provided that the
place for carrying such ballast is properly designed for the weights
involved and adequate means are provided for securing the ballast
and for informing operating personnel of its proper use. In cases
where ballast is permanently installed, it should be plainly marked,
"Do Not Remove."

Compliance Suggestion
USE

OF WEIGHTS

Use of weights for balancing is not recommended except in the


case of two-place gliders when the absence of a passenger will cause
In such cases a standard
the CG to fall outside the certified limits.
weight or set of weights should be supplied with the glider. A
standard means of installation of these weights should be provided
and plainly marked.
126

Maximum airspeed. The flight tests should include steady flight

at the design dive speed (VD) for which compliance with the struc

tural loading requirement

has been proved, except that the speed


need not exceed the value of VD specified.
When high-lift devices
having nonautomatic operation are employed, the tests should also

include steady flight at the design flap speed Vf, except that they need
not involve speeds in excess of 1.67 Vsf. In cases where the high-

lift

devices are automatically operated, the tests should cover the


range of speeds within which the devices are operative.
Airspeed indicator calibration. The airspeed indicator, of the glider
type, should be calibrated in flight unless the instrument is satisfac
torily calibrated by other means and properly located on the glider.
A satisfactory method of calibration should be used.

Compliance Suggestion

In

INSTALLATION CALIBRATION

calibrating the airspeed indicator installation it is important to


have available for computation purposes, the winds aloft, the pressure
The above values
altitude and the free air temperature records.
should be used in conjunction with any of the acceptable calibration
methods described in the following :
a. A free flight over a measured speed course of at least one mile
suitable markers of which should be easily visible to enable observa
tions to be made from the aircraft.
b. A free flight utilizing a trailing pitot-static tube bomb installa
tion connected to a master airspeed indicator, the indications of which
can be used to form a basis for comparison.

OPERATION

LIMITATIONS

Center of gravity limitations. The maximum variation in the loca


tion of the center of gravity for which the glider is certificated to be

Suitable loading charts or schedules


airworthy should be established.
should be provided when necessary to assure that the glider is always
properly loaded.
Towing limitations. Gliders not aircraft towed during official
A suitable placard
flight tests should not be aircraft towed in service.
be
to
so
inform
should
provided
operating personnel.
Airspeed limitations. The maximum certified airspeed {VNE) shall
be limited to .90 VD unless dive brakes are installed which will limit
the terminal velocity of the glider to the VNB speed selected by the
The maximum
designer in which case VNB shall not exceed .95 VD.
certified auto-winch tow speed should be limited to a value of at least
5 m.p.h. less than either the design automobile-winch tow speed (Vum)
or the maximum value attained in the official flight tests, whichever is
lower. The maximum certified aircraft tow speed should be limited
127
657822 O - 62 - 10

to a value of at least

10 percent less than either the design dive


speed (VD) or the maximum speed attained in the official flight tests,
whichever is lower. The maximum certified speed for the operation

of high lift devices should be limited to 5 m.p.h. less than either the
design flap speed (Vf) or the maximum value attained in the official
flight tests, whichever is lower. Means should be provided to affect
such limitations or suitable placards should be used to inform the
operating personnel thereof.
Equipment limitations. Gliders which are not equipped as specified
in Chap. 4 should not be used for any type of operation other than
visual-contact day flying. A suitable placard should be provided
to inform the operating personnel of these limitations.

128

Chapter

6 GLIDERS WITH POWER FOR


SELF-LAUNCHING

The requirements of this chapter are applicable to gliders with


power for self-launching, based upon the premise that power is in
tended to be used for takeoff, climb and intermittent use thereafter.
Flight requirements. The applicable flight and operational limita
tion requirements of either CAR 3, Acrobatic Category, or the flight
and operational limitation recommendations contained herein are
acceptable, provided that a glider with power for self -launching should
meet the additional following conditions at the most critical loading
and include the following information :
a. Power-of condition. It should be demonstrated that the glider
has a rate of sink not in excess of 5 ft./sec.
b. Power-on condition. It should be demonstrated that the glider
has with take-off power at sea level; (1) a rate of climb not less than
200 ft./min., and (2) an angle of climb of at least 1:17.
c. Airspeed and other information. A placard or other suitable
marking should be permanently affixed in easy view of the pilot which
contains the following information:
1. Best airspeed -m.p.h. for climb (speed at which the best rate
of climb was determined) .
2. Best airspeed m.p.h. for obstacle clearance (speed at which
the best angle of climb was determined) .
3. Best airspeed m.p.h. for minimum sinks (speed at which the
minimum rate of sink was determined with full load).
4. Fuel consumption at m.c.p. gal./hr.
Structural requirement. The applicable structural requirements of
either CAR 3, Acrobatic Category or the structural recommendations
in the handbook are acceptable.
Powerplant requirements. The following requirements are applica
ble to all gliders having a powerplant for self -launching:
Scope and general design. The powerplant installation should be
considered to include all components of the powered glider that are
It should also be considered to include all
necessary for propulsion.
components which affect their safety of operation between normal
inspections or overhaul periods.
a. Reciprocating engine installations should comply with the pro
visions of this subpart and such other requirements as may be deemed
necessary by the Federal Aviation Agency.
129

6. All components of the powerplant installation should be con


structed, arranged and installed in a manner which will assure their
continued safe operation between normal inspections or overhaul

periods.

Accessibility should be provided to permit such inspection


maintenance as is necessary to assure continued airworthiness.

and

interconnections should be provided to prevent

the

c.

d.

Electrical

existence of differences of potential between major components of the


powerplant installation and other major portions of the glider which
are electrically conductive.

Engines. All

ENGINES AND PROPELLERS

engines, including all essential accessories, should be


subjected to the block tests and inspections prescribed in the following
subparagraphs.
test. The engine

should be subjected to such calibra


tion tests as are necessary to establish its power characteristics and
the conditions for the endurance test specified in the following sub
paragraphs. The results of the power characteristics calibration
tests should constitute the basis for establishing the characteristics
of the engine over its entire operating range of crankshaft rotational
speeds, manifold pressures, fuel/air mixture settings and altitude.
Power ratings should be based upon standard atmospheric conditions.
a.

Calibration

b. Detonation test. A test should be conducted to establish

that the

engine can function without detonation throughout its range of in

tended conditions of operation, using the lowest grade of fuel specified'

Endurance

test. The endurance

test of an engine with a represen


tative propeller should include a total of 50 hours of operation and
shall consist of the following: The runs should be performed in such
periods and order as are found appropriate by the Federal Aviation
During the endurance test the engine
Agency for the specific engine.
c.

power and crankshaft rotational speed shall be controlled within 3


percent of the specified values.
1.

2.
3.

A one-hour run should

be conducted, consisting of alternate

periods of five (5) minutes at take-off power and speed and 25


minutes at maximum continuous power and speed.
At the end of the one-hour period, the engine will be stopped
and cooled for a (30) thirty-minute period.
The procedures outlined in sections (1) and

be alternately continued

(2)

above will

until the engine has accumulated

total of fifty (50) operating hours.

Propellers. Propellers installed in certificated powered gliders


should be a type which will properly restrain the engine to a speed not
130

exceeding its maximum permissible takeoff speed during takeoff and

initial climb at best-rate-of-climb speed with the engine operating at


full throttle or the throttle setting corresponding to maximum permis

sible takeoff manifold pressure.


A propeller may be approved as a part of the installation

if it satis

factorily withstands the following test.


a. Fixed-pitch wood propellers of a particular pitch, diameter, and
manufacture should withstand without failure two (2) hours of opera
tion at takeoff r.p.m.
metal propellers and adjustable-pitch propellers
b. Fixed-pitch
be
should
subjected to such additional tests as may be required by the
Federal Aviation Agency.
Propeller clearance.
a. Ground clearance should be not less than 7 inches in taxi and
takeoff attitudes.
b. One-inch radial clearance between the blade tips and -the glider
structure, or whatever additional radial clearance is necessary to
preclude harmful vibration of the propeller or glider.
should be provided between any
c. Adequate positive clearance
other rotating parts of the propeller and stationary portions of the
glider.
FUEL SYSTEM

The fuel system should be constructed and arranged in a manner to


assure the provision of fuel to each engine at a flow rate and pressure
adequate for proper engine functioning under all normal conditions

for which engine operation is intended.


Arrangement. Fuel systems should be arranged as to permit any
one fuel pump to draw fuel from only one tank at at ime.
Gravity

feed systems should not supply fuel to any one engine from more than
one tank at a time unless the airspaces are interconnected in such a
manner as to assure that all interconnected tanks feed equally.

Fuel tanks. Fuel tanks should be capable of withstanding, without


failure, any vibration, inertia, fluid, or structural loads to which they
may be subjected in operation. Flexible fuel tank liners should be of
an acceptable type.
Fuel tank tests. Fuel tanks should be capable of withstanding the
following pressure and vibration tests without failure of leakage.
a. Conventional metal tanks and nonmetallic tanks whose walls
are not supported by the glider structure: A pressure of 3.5 p.s.i. for
the first tank of a specific design.
Nonmetallic tanks, the walls of which are supported by the glider
Tanks constructed of an acceptable basic tank material
structure.
and type of construction and with actual or simulated support condi
tions should be subjected to a pressure of 2 p.s.i. for the first tank of a
b.

specific design.

131

e.

Fuel tanks which are subject to engine vibration shall, together

with supports, be subjected to the following vibration test when


The tank
mounted in a manner simulating the actual installation.
a
should
for
25
hours
at
total
be vibrated
assembly
amplitude of not
The frequency of
less than Hj of an inch while filled % full of water.
should
be
of
the
rated
takeoff
vibration
90 percent
speed of the engine
unless some other frequency within the normal operating range of
speeds of the engine is more critical, in which case the latter speed
shall be employed and the time of the test shall be adjusted to accomp
lish the same number of vibration cycles.
Fuel tank installation.

a.

The method of supporting the tanks should not be such as to

concentrate the loads resulting from the weight of the fuel in the
tanks. Materials employed for supporting, or padding the support
ing members of the tank should be nonabsorbent or shall be treated
to prevent absorption of fuel.

Fuel tank compartments should be ventilated and drained to


prevent accumulation of flammable fluids or vapors. Compartments
adjacent to the tanks should be treated in a like manner.
c. Fuel tanks should not be located on the engine side of the firewall.
Not less than 3^-inch of clear airspace should be provided between
the fuel tank and the firewall.
d. Fuel tank capacity should not exceed 5 gallons.
Tanks may be
installed in personnel compartments if adequate ventilation and drain
age are provided and it can be demonstrated that the location of the
tank will in no way interfere with the operation of any part of the
In all other
glider or the normal movements of light personnel.
cases, fuel tanks should be isolated from personnel compartments by
means of fume and fuelproof enclosures.
Fuel system lines and fittings. Fuel lines should be installed and
supported in a manner which will prevent excessive vibration and will
be adequate to withstand loads due to fuel pressure and accelerated
flight conditions. Lines which are connected to components of the
glider between which relative motion might exist should incorporate
provisions for flexibility.
Flexible hose should be of an acceptable
type.
Fuel sumps. Each fuel tank should be provided with a drainable
sump having a capacity of not less than 0.10 percent of the tank
capacity or %t gallon, whichever is the greater.
It should be accept
able to dispense with the sump if the fuel system is provided with a
sediment bowl permitting ground inspection and drainage.
The
capacity of the sediment chamber should not be less than one (1)
b.

ounce.

Fuel vents. Fuel tanks should be vented from the top portion of
the tank.
Vent outlets should be located and constructed as to
132

minimize the possibility of the vent icing or becoming obstructed


by other foreign matter and shall discharge clear of the glider. Fuel
should not siphon or drain from the vent during normal operation or
when the engine is in the fully retracted position.

OIL SYSTEM
Each engine should be provided with an independent oil system
capable of supplying the engine with an ample quantity of oil at a
temperature not exceeding the maximum which has been established
as safe for continuous operation except that two-cycle engines using
a single tank to supply a fuel/oil mixture to the engine need not com
ply with this section.
Oil tanks. Oil tanks shall be capable of withstanding without
failure any vibration, inertia, fluid, or structural loads to which they
Flexible oil tank liners shall be of an
may be subjected in operation.
acceptable type.
Oil tank tests.
a. Oil tanks should be subjected to the same tests as fuel tanks
except pressure test at 5 p.s.i.

b. For a two-cycle engine using a common tank to supply a fuel/oil


mixture to the engine, the pressures applicable to fuel tank installa
tion should apply.
Oil tank installation. Oil tank installation should comply with the
requirements of fuel tank installations.
Oil system lines and fittings. Oil system lines should comply with
the same installation requirements as used for the fuel system lines
and fittings except that the inside diameter of the engine oil inlet
and outlet lines should not be less than the diameter of the correspond
ing engine oil pump inlet and outlet.
Oil breather lines.
a. Engine breather lines should be arranged so that condensed
water vapor which might freeze and obstruct the line cannot accumu
late at any point.
b. Breathers should discharge in a location which will not constitute
a fire hazard in case foaming occurs and so that oil emitted from the
line will not impinge on the pilot's windshield.
The breather should
not discharge into the engine air induction system.
Drainage through
the breather should not be possible when engine is fully retracted.

COOLING

The powerplant cooling provision should be capable of maintaining


the temperature of all powerplant components, engine parts and en
gine fluids (oil and coolant), at or below the maximum established
safe values under critical conditions of ground, takeoff, and climb
operation.
133

test. The

cooling test to determine that the maximum


which
the
engine can withstand will not be exceeded
temperatures
should be conducted by starting and running the engines on the ground
until normal engine warmup temperature has been stabilized. The
glider shall then proceed with normal takeoff and climb at bestrate-of-climb speed. The power used should be takeoff power and
Cooling

power and speed. The climb


should continue for approximately 5 minutes after the temperature
peak or dropoff, to assure that stabilization had been reached.
speed

and

maximum

continuous

INDUCTION SYSTEM
The engine air induction system should permit supplying an ade
quate quantity of air to the engine under all conditions of operation.

Induction system ducts. Induction system ducts should be pro


vided with drains which will prevent the accumulation of fuel or
moisture in all normal ground and flight attitudes. Drains should
not discharge in a location which will constitute a fire hazard. Ducts
which are connected to components of the glider between which rela
tive motion may exist should incorporate provisions for flexibility.
Induction

system screens.

Where induction system screens or filters

they should be located upstream from the carburetor.


should not be possible for fuel to impinge upon the screen.

are employed,

It

EXHAUST SYSTEM
The exhaust system should be constructed and arranged in such a
manner as to assure the safe disposal of exhaust gases without the
existence of a fire hazard or contamination of the air in personnel
compartments with carbon monoxide.
Unless other suitable pre
cautions are taken, all exhaust system components should be separ
ated from adjacent flammable portions of the glider by means of
Exhaust gases should not be discharged within
fireproof shields.

proximity of any fuel or oil system drains. All exhaust


system components should be ventilated to prevent the existence of
points of excessively high temperature.
dangerous

Exhaust manifold. Exhaust manifolds should be made of fireproof,


corrosion-resistant materials, and shall incorporate provisions to
prevent failure due to their expansion when heated to operating tem
Exhaust manifolds should be supported in a manner
peratures.
adequate

to withstand all vibration and inertia loads to which they

might be subjected in operation.

Portions of the manifold which


are connected to components between which relative motion might
exist should incorporate provisions for flexibility.
134

FIREWALL AND COWLING

Firewalls. All engines, fuel burning heaters, and other combustion


equipment which are intended for operation during takeoff or flight
should be isolated from the remainder of the glider by means of fire
walls, shrouds, or other equivalent means.

Firewall construction.
a. Firewalls and shrouds should be constructed in such a manner

that no hazardous quantity of liquids, gases, or flame could pass from


the engine compartment to other portions of the glider.
b. Firewalls and shrouds should be constructed of fireproof material
and protected against corrosion.
c. Where the engine, during operation, is situated so that the proba
ble path of an engine fire would not contact the glider structure, fire
walls and shrouds may be constructed of fire-resistant materials.

Cowling.
a. Cowling should be constructed and supported in such a manner
as to be capable of resisting all vibration, inertia, and air loads to
Provision should be made to
which it may normally be subjected.
permit rapid and complete drainage of all portions of the cowling
in all normal ground and flight attitudes. Drains must not discharge
in locations constituting a fire hazard.
All
b. Cowling should be constructed of fire-resistant material.
portions of the glider lying behind openings in the engine compart
ment cowling should also be constructed of fire-resistant materials for
a distance of at least 24 inches aft of such openings.
Portions of
cowling which are subjected to high temperature due to proximity to
exhaust system ports or exhaust gas impingement should be con
structed of fireproof material.
Retractable engine assembly.

which retract into any part of the glider


should be installed in such a manner as to avoid the possibility of fire
occurring or other hazardous effects due to residual heat, with the
engine in the retracted position.
b. Fuel or oil should not drain from the engine, its components,
or
items of equipment installed on the engine assembly when the engine
assembly is in the retracted position.
a. Engine

assemblies

POWER PLANT CONTROLS AND ACCESSORIES


Power plant controls.
a.

Throttle controls. A throttle control should be provided to give

independent control for each engine.


Throttle controls should afford
a positive and immediately responsive means of controlling the engine.
b. Ignition switches. Ignition switches should provide control for
each ignition circuit on each engine.
135

Mixture controls. If mixture controls are provided, a separate


The controls should be
control should be provided for each engine.
grouped and arranged in such a manner as to permit both separate
and simultaneous control of all engines.
Location. All powerplant controls should be located so as to pro
vide convenience in operation including provisions to prevent inad
vertent operation. The controls should be located and arranged so
that when the pilot is seated it will be readily possible for him to obtain
full and unrestricted movement of each control without interference
from either his clothing or the cockpit structure.
Markings. All powerplant controls should be plainly marked as to
their function and method of operation. Controls for fuel tank selec
tor valve should be marked to indicate the position corresponding to
each tank and to all existing cross feed positions.
When more than
one fuel tank is provided, and if safe operation depends upon the use
of tanks in a specific sequence, the fuel tank selector controls should
be marked adjacent to or on the control to indicate to the pilot the
order in which the tanks must be used.
Construction. Controls should maintain any necessary position
without constant attention by the flight personnel and shall not tend
Flexible controls should
to creep due to control loads or vibration.
be of an acceptable type. Controls should have adequate strength
and rigidity to withstand loads without failure or excessive deflection.
Movement. The direction of movement of controls should be as
follows :
a. Throttle: Forward to increase forward thrust.
b. Propeller: Forward to increase r.p.m.
c. Mixture : Forward or upward for rich.
c.

ACCESSORIES

Powerplant accessories. Engine-driven

accessories should be of a
for
on
the
satisfactory
installation
type
engine involved and shall
utilize the provisions made on the engine for the mounting of such
units. Items of electrical equipment subject to arcing or sparking
should be installed so as to minimize the possibility of their contact
with any flammable fluids or vapors which might be present in a free
state.

EQUIPMENT
Required

basic equipment.

The following table

equipment required for type and


glider:
Flight instruments.
a.
b.
c.

Airspeed indicator.
Altimeter.

Magnetic direction indicator.


136

shows

the basic

airworthiness certification of

Powerplant instruments. For each engine or tank.


a. Tachometer.
b. Fuel quantity indicator.
c. Oil temperature indicator (not for two-cycle engines).
d. Oil pressure indicator (not for two-cycle engines) .
e. Powerplant instrument lines carrying flammable fluids or gases
under pressure should be provided with restricted orifices or other
safety devices at the source of the pressure to prevent escape of
excessive fluid or gas in case of line failure.

137

7 MISCELLANEOUS

Chapter

RECOMMENDATIONS
GENERAL

Standard weights. In computing

values should be used

Pilot and passengers

(Also

see

weights

Chap. 6.)

Parachutes
Water

the following standard


170 lbs. per person

20 lbs. each

8.5 lbs. per gallon

Adequate means should be provided for determin


Leveling means.
ing when the glider is in a level position.

It is most advisable to

provide a leveling means in order that rigging


may be checked, and so that necessary load tests may be conducted.
There is no standard definition of level position for gliders.
However,
any arbitrary reference may be used, such as a longeron or a line be
All rigging instructions
tween bolt holes in one wing root fitting.
should require only the more common and inexpensive measuring
devices, such as straight edges, ordinary scales, and spirit levels.
Only reasonable accuracy in any measurement normally is necessary.

139
U. S. GOVERNMENT

PRINTING OFFICE : 1962 O - 657822

l25r,R3 20 t3

BN

6333

You might also like