Philips TDA9874 PDF
Philips TDA9874 PDF
Philips TDA9874 PDF
DATA SHEET
TDA9874A
Digital TV sound
demodulator/decoder
Preliminary specification
File under Integrated Circuits, IC02
1999 Dec 03
Philips Semiconductors
Preliminary specification
FEATURES
GENERAL DESCRIPTION
2.1
Supported standards
ORDERING INFORMATION
BLOCK DIAGRAM
PINNING
FUNCTIONAL DESCRIPTION
6.1
6.2
6.3
LIMITING VALUES
THERMAL CHARACTERISTICS
CHARACTERISTICS
10
I2C-BUS CONTROL
10.1
10.2
10.3
10.4
Introduction
Power-up state
Slave receiver mode
Slave transmitter mode
11
I2S-BUS DESCRIPTION
12
EXTERNAL COMPONENTS
13
PACKAGE OUTLINES
14
SOLDERING
14.1
14.2
14.3
14.4
Introduction
Through-hole mount packages
Surface mount packages
Suitability of IC packages for wave, reflow and
dipping soldering methods
15
DEFINITIONS
16
17
1999 Dec 03
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
FEATURES
2.1
Supported standards
Standby mode
Automatic output selection for TV applications.
1999 Dec 03
GENERAL DESCRIPTION
Philips Semiconductors
Preliminary specification
TDA9874A
STANDARD
CARRIER
FREQUENCY
(MHz)
FM DEVIATION (kHz)
NOM.
MAX.
OVER.
MODULATION
SC1
mono
4.5
15
25
50
A2
4.5/4.724
15
25
50
2(L + R)
B/G
A2
5.5/5.742
27
50
80
2(L
mono
6.0
27
50
80
A2
6.5/6.742
27
50
80
I
D/K (2)
D/K (1)
A2
6.5/6.258
D/K (3)
A2
6.5/5.742
Table 2
27
50
27
50
SC2
BANDWIDTH/
DE-EMPHASIS
(kHz/s)
mono
1
2(L R)
+ R)
15/75
15/75 (Korea)
15/50
mono
15/50
2(L + R)
15/50
80
2(L
+ R)
15/50
80
2(L
+ R)
15/50
A2; A2*
A2+ (KOREA)
Pilot frequency
line frequency
117.5 Hz = --------------------------------------133
line frequency
149.9 Hz = --------------------------------------105
line frequency
274.1 Hz = --------------------------------------57
line frequency
276.0 Hz = --------------------------------------57
AM modulation depth
50%
50%
2.1.2
Table 3
STANDARD
FREQUENCY
TYPE
(MHz)
DEVIATION
(kHz)
INDEX (%)
NOM.
MAX.
NOM.
MAX.
SC2
DEROLLNICAM
(MHz)
EMPHASIS OFF (%) CODING
NICAM
B/G
5.5
FM
27
50
5.85
J17
40
note 1
6.0
FM
27
50
6.552
J17
100
note 1
D/K
6.5
FM
27
50
5.85
J17
40
note 2
6.5
AM
54
100
5.85
J17
40
note 1
Notes
1. See EBU NICAM 728 specification or equivalent specification.
2. Not yet officially defined.
1999 Dec 03
Philips Semiconductors
Preliminary specification
TDA9874A
SATELLITE SYSTEMS
An important specification for satellite TV reception is the Astra specification. The TDA9874A is suitable for the reception
of Astra and other satellite signals, with sound carrier frequencies from 4 to 9.2 MHz.
Table 4
FM satellite sound
CARRIER TYPE
Main
Sub
CARRIER
FREQUENCY
(MHz)
MODULATION
INDEX
MAXIMUM
FM DEVIATION
(kHz)
MODULATION
BANDWIDTH/
DE-EMPHASIS
(kHz/s)
6.50(1)
0.26
85(2)
mono
15/50(1)
50
m/st/d(3)
15/adaptive(4)
7.02/7.20
0.15
7.38/7.56
7.74/7.92
8.10/8.28
Notes
1. For other satellite systems, frequencies of e.g. 5.80, 6.60 or 6.65 MHz can also be received. A de-emphasis of 60 s,
or in accordance with J17, is available.
2. Main channels with high deviation can also be handled.
3. m/st/d = mono or stereo or dual language sound.
4. Adaptive de-emphasis is compatible to transmitter specification.
3
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
DESCRIPTION
VERSION
TDA9874APS
SDIP42
SOT270-1
TDA9874AH
QFP44
SOT205-1
1999 Dec 03
Philips Semiconductors
Preliminary specification
TDA9874A
BLOCK DIAGRAM
SIF2
SIF1
27 (23)
P1
P2
ADDR1
ADDR2
SCL
SDA
29 (25)
41 (37)
(21) 25
4 (42)
(20) 24
18 (13)
23 (19)
I2C-BUS
INTERFACE
INPUT SWITCH
AGC, ADC
33 (29)
34 (30)
IDENTIFICATION
SUPPLY
SIF
FM/AM
DEMODULATION
(28) 32
(27) 31
(24) 28
(18) 22
(10) 15
NICAM
DEMODULATION
(12) 17
(8)
XTALI
XTALO
SYSCLK
20 (15)
19 (14)
(7) 13
NICAM
DECODER
DEMATRIX
CLOCK
38 (34)
(6) 12
(5) 11
DIGITAL
SUPPLY
PEAK
DETECTION
(35) 39
(36) 40
2-CHANNEL
ANALOG/
SATELLITE
DECODER
(26) 30
LEVEL
ADJUST
(3) 9
SDO
WS
SCK
SUPPLY
DACs
OPAMPS
35 (31)
36 (32)
37 (33)
I2S-BUS
INTERFACE
POST FILTER
3 DACs
DIGITAL
SELECTOR
REFERENCE
TEST2
TP1
TP2
TP3
(44) 6
(41) 3
(39) 1
TDA9874APS
(TDA9874AH)
TEST1
(4) 10
ANALOG
CROSSBAR
SWITCH
(40) 2
(38) 42
26 (22)
21 (17)
16 (11)
MONO
CHANNEL
OUTPUT
BUFFERS
TEST
14 (9)
(16)
5 (43)
2-CHANNEL
OUTPUT
BUFFERS
7 (1)
8 (2)
MHB584
OUTM
1999 Dec 03
OUTL
OUTR
VDEC
VSSA2
VDDA3
VSSA3
Vref1
Iref
NICAM
PCLK
n.c.
VSSD2
VDDD1
VSSD1
VDDD3
VSSD3
CRESET
VDDA1
VSSA1
VSSA4
Vref 2
EXTIR
EXTIL
MONOIN
Philips Semiconductors
Preliminary specification
TDA9874A
PINNING
PIN
SYMBOL
DESCRIPTION
SDIP42
QFP44
EXTIR
39
EXTIL
40
Vref2
41
P2
42
OUTM
43
VSSA4
44
OUTL
OUTR
VDDA1
VSSA1
10
VSSD1
11
VDDD1
12
VSSD2
13
n.c.
not connected
TP2
14
NICAM
15
10
TP1
16
11
PCLK
17
12
ADDR1
18
13
XTALO
19
14
XTALI
20
15
TP3
16
TEST2
21
17
Iref
22
18
ADDR2
23
19
VSSA2
24
20
VDEC
25
21
TEST1
26
22
SIF2
27
23
sound IF input 2
Vref1
28
24
SIF1
29
25
sound IF input 1
CRESET
30
26
VSSA3
31
27
VDDA3
32
28
SCL
33
29
SDA
34
30
SDO
35
31
WS
36
32
1999 Dec 03
Philips Semiconductors
Preliminary specification
TDA9874A
PIN
SYMBOL
DESCRIPTION
SDIP42
QFP44
SCK
37
33
SYSCLK
38
34
VDDD3
39
35
VSSD3
40
36
P1
41
37
MONOIN
42
38
handbook, halfpage
EXTIR
42 MONOIN
EXTIL
41 P1
Vref2
40 VSSD3
P2
39 VDDD3
OUTM
38 SYSCLK
VSSA4
37 SCK
OUTL
36 WS
OUTR
35 SDO
VDDA1
34 SDA
VSSA1 10
33 SCL
31 VSSA3
VSSD2 13
30 CRESET
TP2 14
29 SIF1
NICAM 15
28 Vref1
TP1 16
27 SIF2
PCLK 17
26 TEST1
ADDR1 18
25 VDEC
XTALO 19
24 VSSA2
XTALI 20
23 ADDR2
22 Iref
TEST2 21
MHB585
1999 Dec 03
Philips Semiconductors
Preliminary specification
34 SYSCLK
35 VDDD3
36 VSSD3
37 P1
TDA9874A
38 MONOIN
39 EXTIR
40 EXTIL
41 Vref2
42 P2
44 VSSA4
43 OUTM
OUTL 1
33 SCK
OUTR 2
32 WS
VDDA1 3
31 SDO
VSSA1 4
30 SDA
VSSD1 5
29 SCL
VDDD1 6
28 VDDA3
TDA9874AH
VSSD2 7
27 VSSA3
TEST1 22
VDEC 21
VSSA2 20
ADDR2 19
23 SIF2
Iref 18
TP1 11
TEST2 17
24 Vref1
TP3 16
NICAM 10
XTALI 15
25 SIF1
XTALO 14
TP2 9
ADDR1 13
26 CRESET
PCLK 12
n.c. 8
MHB586
FUNCTIONAL DESCRIPTION
6.1
6.1.1
6.1.3
SIF INPUT
Two input pins are provided, SIF1 and SIF2. For higher
SIF signal levels the SIF input can be attenuated with an
internal switchable 10 dB resistor divider. As no specific
filters are integrated, both inputs have the same
specification giving flexibility in application. The selected
signal is passed through an AGC circuit and then digitized
by an 8-bit ADC operating at 24.576 MHz.
6.1.2
MIXER
AGC
6.1.4
FM AND AM DEMODULATION
Philips Semiconductors
Preliminary specification
The status of the NICAM decoder can be read out from the
NICAM status register by the user (see Section 10.4.2).
The OSB bit indicates that the decoder has locked to the
NICAM data. The VDSP bit indicates that the decoder has
locked to the NICAM data and that the data is valid sound
data. The C4 bit indicates that the sound conveyed by the
FM mono channel is identical to the sound conveyed by
the NICAM channel.
FM DECODING
FM IDENTIFICATION
6.1.9
NICAM DEMODULATION
NICAM DECODING
1999 Dec 03
NICAM AUTO-MUTE
TDA9874A
10
Philips Semiconductors
Preliminary specification
CRYSTAL OSCILLATOR
TEST PINS
TDA9874A
V
handbook, halfpage
5
MHB587
1.5
reset active
guaranteed
t
6.2
POWER-ON RESET
6.2.1
6.2.2
NICAM PATH
6.2.3
1999 Dec 03
NICAM AUTO-MUTE
11
Philips Semiconductors
Preliminary specification
6.2.7
FM (AM) PATH
6.2.8
MONITOR
6.2.9
GENERAL
1999 Dec 03
6.2.6
6.2.5
TDA9874A
12
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
FIXED
DE-EMPHASIS
NICAM
stereo DACs
LEVEL
ADJUST
DIGITAL
CROSSBAR
SELECT
mono DAC
LEVEL
ADJUST
13
FM
DC
FILTER
ADAPTIVE
DE-EMPHASIS
FIXED
DE-EMPHASIS
2-CHANNEL
DECODER
LEVEL
ADJUST
MATRIX
I2S-bus
MONITOR
I2C-bus
Philips Semiconductors
LEVEL
ADJUST
1999 Dec 03
LEVEL
ADJUST
MHB588
Preliminary specification
TDA9874A
Philips Semiconductors
Preliminary specification
6.3.2
6.3.1
TDA9874A
EXTERNAL AND MONO INPUTS
6.3.3
AUDIO DACS
6.3.4
Table 5
6.3.5
MATRIX OUTPUT
MODE
L OUTPUT
R OUTPUT
L input
R input
R input
L input
L input
L input
R input
R input
source select
STANDBY MODE
matrix
mono (AM)
EXTIL
OUTL
EXTIR
DACL
OUTR
DACR
OUTM
DACM
MHB589
1999 Dec 03
14
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
NICAM
NICAM
DEMODULATOR
NICAM
DECODER
LEVEL
ADJUST
LEVEL
ADJUST
DE-EMPHASIS
15
DIGITAL
CROSSBAR
SELECT
FM/AM
FM/AM
DEMODULATOR
ADAPTIVE
DE-EMPHASIS
FIXED
DE-EMPHASIS
2-CHANNEL
DECODER
LEVEL
ADJUST
DACs
MATRIX
BUFFER
STEREO
OUTPUT
MATRIX
BUFFER
MONO
OUTPUT
MATRIX
LEVEL
ADJUST
I2S-bus
AVL
Philips Semiconductors
ANALOG
CROSSBAR
SWITCH
external
1999 Dec 03
mono
MHB590
Preliminary specification
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
7 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
VDDx
DC supply voltage
0.5
+6.5
VDDx
550
mV
IIK
10
mA
IOK
Vo < 0.5 V or
Vo > VDD + 0.5 V
20
mA
IO
20
mA
96
mA
IDDA, ISSA
50
mA
Ilu(prot)
100
mA
P/out
100
mW
Ptot
0.75
Tstg
storage temperature
55
+125
Tamb
ambient temperature
20
+70
Ves
electrostatic handling
note 1
2000
note 2
200
Notes
1. Human body model: C = 100 pF; R = 1.5 k.
2. Machine model: C = 200 pF; L = 0.75 H; R = 0 .
8
THERMAL CHARACTERISTICS
SYMBOL
Rth(j-a)
PARAMETER
CONDITIONS
1999 Dec 03
in free air
16
VALUE
UNIT
70
K/W
Philips Semiconductors
Preliminary specification
TDA9874A
9 CHARACTERISTICS
VDD = 5 V; Tamb = 25 C; settings in accordance with B/G standard; FM deviation 50 kHz; fmod = 1 kHz; FM sound
parameters in accordance with system A2; NICAM in accordance with EBU NICAM 728 specification; 1 k
measurement source resistance for AF inputs; VSIF = 300 mV (p-p); AGCOFF = 0; AGCSLOW = 1; level and gain
settings according to note 1 with external components of Fig.9; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Digital supplies
VDDD1
4.5
5.0
5.5
VSSD1
0.0
IDDD1
VDDD1 = 5.5 V
40
59
74
mA
VDDD1 = 5.0 V
42
59
75
mA
0.0
VSSD2
VDDD3
4.5
5.0
5.5
VSSD3
0.0
IDDD3
17
21
mA
16
20
mA
4.0
4.5
5.0
5.5
VSSA3
0.0
IDDA3
VDDA3 = 5.5 V
24
32
40
mA
VDDA3 = 5.0 V
24
32
40
mA
VDEC1
3.3
VSSA2
0.0
Vref1
Iref1(sink)
200
4.5
5.0
5.5
VSSA1
0.0
IDDA1
10
mA
10
mA
VSSA4
0.0
Vref2
50
20
VDDA1 = 5.5 V
VDDA1 = 5.0 V
17
Philips Semiconductors
Preliminary specification
SYMBOL
PARAMETER
TDA9874A
CONDITIONS
MIN.
TYP.
MAX.
UNIT
20
0.3VDDD V
CMOS level input, high drive, pull-down (pins TEST1, TEST2, TP1 and TP2)
VIL
VIH
0.7VDDD
Ci
input capacitance
10
pF
Zi
input impedance
50
0.3VDDD V
VIH
0.7VDDD
Vhys
hysteresis voltage
1.3
Ci
input capacitance
10
pF
Zi
input impedance
50
0.3VDDD V
INPUTS/OUTPUTS
I2C-bus level input with Schmitt trigger, open-drain output stage (pins SCL and SDA)
VIL
VIH
0.7VDDD
Vhys
hysteresis voltage
0.05VDDD
ILI
10
Ci
input capacitance
10
pF
VOL
0.6
CL
load capacitance
400
pF
TTL/CMOS level, high drive, 4 mA 3-state output stage, pull-up (pins PCLK, NICAM, ADDR1, ADDR2, P1, P2, SCK,
WS and SDO)
0.8
2.0
input capacitance
10
pF
IOL = 3 mA
0.4
IOH = 3 mA
2.4
CL
load capacitance
active pull-up
100
pF
Zi
input impedance
50
0.3VDDD V
VIL
VIH
Ci
VOL
VOH
OUTPUTS
IOL = 2 mA
IOH = 2 mA
VOH
CL
load capacitance
ILO(Z)
1999 Dec 03
Vi = 0 to VDDD
18
0.7VDDD
100
pF
10
Philips Semiconductors
Preliminary specification
SYMBOL
PARAMETER
TDA9874A
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VSIF(min)(p-p)
941
mV
2976
mV
59
mV
188
mV
24
dB
9.2
MHz
10
7.5
11
pF
AGC
AGC range
fi
input frequency
Ri
input resistance
Ci
input capacitance
fFM
FM deviation
100
kHz
fFM(FS)
kHz
fFM(max)
kHz
C/NFM
FM carrier-to-noise ratio
77
C/NN
66
ct
crosstalk attenuation
SIF1 to SIF2
fi = 4 to 9.2 MHz
50
dB
400
500
600
mV
AGCLEV = 0
dB
------Hz
dB
------Hz
Demodulator performance
Vo(nom)(rms)
note 1
THD + N
0.3
0.5
0.1
0.3
1999 Dec 03
19
Philips Semiconductors
Preliminary specification
SYMBOL
S/N
B(3dB)
PARAMETER
signal-to-noise ratio
3 dB bandwidth
TDA9874A
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Vo = 1 V (RMS);
CCIR468-2; quasi peak
SC1 from FM source to
any output
64
70
dB
60
66
dB
62
68
dB
NICAM source
14.5
15
kHz
14.5
15
kHz
fresp
frequency response
20 Hz to 14 kHz
+1
dB
cd(dual)
note 3
65
70
dB
cs(stereo)
note 4
40
AM
AM suppression for FM
dmAM
AM demodulation
45
dB
dB
36
45
dB
25
50
75
C/Npilot(ident)
27
hys(tun)
hysteresis
dB
fident
identification window
slow mode
116.85
118.12
Hz
medium mode
116.11
118.89
Hz
fast mode
114.65
120.46
Hz
slow mode
273.44
274.81
Hz
medium mode
272.07
276.20
Hz
dB
------Hz
B/G stereo
B/G dual
270.73
277.60
Hz
slow mode
medium mode
fast mode
0.5
fast mode
ton(ident)
1999 Dec 03
20
Philips Semiconductors
Preliminary specification
SYMBOL
toff(ident)
PARAMETER
total identification time off
TDA9874A
CONDITIONS
MIN.
TYP.
MAX.
UNIT
slow mode
medium mode
fast mode
0.5
note 1
500
mV
Vi(cl)(rms)
1250
1400
mV
Ri
input resistance
note 5
28
35
42
THD < 3%
1400
mV
Ro
output resistance
150
250
375
RL(AC)
AC load resistor
10
RL(DC)
DC load resistor
10
Co(L)
10
12
nF
Voffset(DC)
30
70
mV
mute
mute suppression
80
dB
Bline
bandwidth
20
kHz
Gro
dB
PSRR
fripple = 70 Hz;
Vripple = 100 mV (peak);
CVref = 47 F; signal from
I2S-bus
40
45
dB
Audio performance
THD + N
Vin/out = 1 V (RMS);
fi = 1 kHz; bandwidth
20 Hz to 20 kHz; from
external/mono input to
output copy
0.1
0.3
S/N
signal-to-noise ratio
reference voltage
V0 = 1.4 V (RMS);
fi = 1 kHz; CCIR468-2;
quasi peak; from external or
mono input to output copy
78
90
dB
ct
crosstalk attenuation
70
dB
cs
channel separation
65
dB
60
dB
1999 Dec 03
21
Philips Semiconductors
Preliminary specification
SYMBOL
PARAMETER
TDA9874A
CONDITIONS
MIN.
TYP.
MAX.
UNIT
crystal frequency
24.576
MHz
CL
load capacitance
20
pF
C1
series capacitance
20
fF
C0
parallel capacitance
pF
pull
pulling sensitivity
CL changed from
18 to 16 pF
25
RR
at nominal frequency
30
RN
2RR
temperature range
20
+25
+70
XJ
adjustment tolerance
30
106
XD
drift
30
106
XA
ageing
note 6
10
----------pF
10
----------year
Notes
1. Definition of levels and level setting:
a) The full-scale level for analog audio signals is VFS = 1.4 V (RMS). The nominal level at the digital crossbar switch
is defined at 15 dB (FS).
b) Nominal audio input levels: external, mono: 500 mV; 9 dB (FS).
2. Audio performance is limited by the dynamic range of the NICAM 728 system. Due to companding, the quantization
noise is never lower than 62 dB with respect to the input level.
3. FM source; in dual mode only A (respectively B) signal modulated; measured at B (respectively A) channel output;
Vo = 1 V (RMS) of modulated channel.
4. FM source; in stereo mode only L (respectively R) signal modulated; measured at R (respectively L) channel output;
Vo = 1 V (RMS) of modulated channel.
5. If the supply voltage for the TDA9874A is switched off, because of the ESD protection circuitry, all audio input pins
are short-circuited.
6. The Philips crystal (order number 9922 520 20106) is suitable for this application.
1999 Dec 03
22
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
TRANSMITTER NOMINAL
MODULATION DEPTH
NOMINAL LEVEL AT
DEMODULATOR OUTPUT
LEVEL
ADJUSTMENT
SETTING
FM
15 kHz deviation
M standard
24 dB (FS)
+9 dB
FM
B/G, D/K, I
standard
27 kHz deviation
19 dB (FS)
+4 dB
AM
L/L accent
standard
54%
19 dB (FS)
+4 dB
NICAM
B/G, D/K,
L standard
11.2 dB (FS)
18 dB (FS)
+3 dB
NICAM
I standard
15.8 dB (FS)
23 dB (FS)
+8 dB
23
NOMINAL LEVEL
AT CROSSBAR
DAC GAIN
SETTING
NOMINAL OUTPUT
VOLTAGE VO
15 dB (FS)
(spread of 0.5 dB
due to different
transmitter
references)
+6 dB
500 mV (RMS)
MAXIMUM LEVEL
AT CROSSBAR
DAC GAIN
SETTING
MAXIMUM OUTPUT
VOLTAGE VO
9 dB (FS)
+6 dB
1 V (RMS)
TRANSMITTER
MAXIMUM MODULATION
DEPTH
NOMINAL LEVEL AT
DEMODULATOR OUTPUT
LEVEL
ADJUSTMENT
SETTING
SAT FM
stereo
50 kHz deviation
13 dB (FS)
+4 dB
SAT FM
mono
85 kHz deviation
9 dB (FS)
0 dB
Philips Semiconductors
SOURCE
1999 Dec 03
Preliminary specification
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
10 I2C-BUS CONTROL
10.2
10.1
Introduction
Power-up state
AGC on
SIF 10 dB attenuator off
Small hysteresis.
Demodulators for both sound carriers set to FM with:
Identification for B/G, D/K, identification mode slow
Level adjustment set to 0 dB
De-emphasis 50 s
Dematrix set to mono
ADDR1
A6
A5
A4
A3
A2
A1
A0
1999 Dec 03
24
Philips Semiconductors
Preliminary specification
TDA9874A
SLAVE ADDRESS
0 A
SUBADDRESS
DATA
A/NA
A/NA
FUNCTION
START condition
SLAVE ADDRESS
acknowledge
SUBADDRESS
DATA
A/NA
STOP condition
SLAVE ADDRESS
10.3.1
0 A
SUBADDRESS
DATA BYTE A
n data bytes with auto-increment of
subaddresses
DATA
The TDA9874A can be programmed in the same way as its predecessor (TDA9874H) using the subaddresses 0 to 24
or by using ESP.
1999 Dec 03
25
Philips Semiconductors
Preliminary specification
10.3.1.2
TDA9874A
NAME
AGCCGR
set AGCGR = 20H for using the 10 dB attenuator at the SIF input, otherwise write a 00H to
this register
GCONR
select the chosen SIF input pin by writing data to bit SIFSEL (bit 0) and choose the AGC
decay time corresponding to your application by writing the appropriate data to bit
AGCSLOW (bit 2)
MSR
3 to 10
11
FMMR
12
C1OLAR
see Table 38
13
C2OLAR
see Table 39
14
NCONR
15
NOLAR
see Table 42
16
NLELR
set NLELR = 14H (default setting after Power-on reset) if no other value is chosen
17
NUELR
set NUELR = 50H (default setting after Power-on reset) if no other value is chosen
18
AMCONR
19
SDACOSR
Set SDACOSR = 81H to select +6 dB gain (see Table 48) and NICAM or FM output.
20
AOSR
To select an internal source set AOSR = 80H to select dual A or set AOSR = C0H to select
dual B (if dual mode is transmitted) to all analog outputs. For selecting an external source
see Section 10.3.18.
21
DAICONR
use only for I2S-bus output, see detailed description in Section 10.3.19
22
I2SOSR
use only for I2S-bus output, see detailed description in Section 10.3.20
23
I2SOLAR
use only for I2S-bus output, see detailed description in Section 10.3.21
24
MDACOSR Set MDACOSR = 82H to select dual A or set MDACOSR = 83H to select dual B (if dual
mode is transmitted) to all analog outputs. For selecting an external source see
Section 10.3.22.
255
ESP
1999 Dec 03
26
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
27
AGCLEV
B4
B3
B2
B1
B0
P2OUT
P1OUT
STDBY
INIT
CLRPFR
AGCSLOW
AGCOFF
SIFSEL
general configuration
PEAK
MCSM1
MCSM0
MSS1
MSS0
B7
B6
B5
B4
B3
B2
B1
B0
carrier 1 frequency;
MS part
B7
B6
B5
B4
B3
B2
B1
B0
carrier 1 frequency
B7
B6
B5
B4
B3
B2
B1
B0
carrier 1 frequency;
LS part
B7
B6
B5
B4
B3
B2
B1
B0
carrier 2 frequency;
MS part
B7
B6
B5
B4
B3
B2
B1
B0
carrier 2 frequency
B7
B5
B5
B4
B3
B2
B1
B0
carrier 2 frequency;
LS part
IDMOD1
IDMOD0
IDAREA
FILTBW1
10
ADEEM2
FMDSC23
11
IDSWFM
12
13
14
FUNCTION
DCXOPULL DCXOTEST
FMDSC22 FMDSC21
CH2MOD1 CH2MOD0
monitor select
FILTBW0
CH1MODE demodulator
configuration
FMDSC11 FM de-emphasis
ADEEM1
FMDSC13
FMDSC12
FDMS2
FDMS1
FDMS0
B4
B3
B2
B1
B0
B4
B3
B2
B1
B0
DOUTEN
AMSEL
NDEEM
AMUTE
NICAM configuration
Philips Semiconductors
DATA
SUBADDRESS
(DECIMAL)
1999 Dec 03
FM dematrix
B4
B3
B2
B1
B0
16
B7
B6
B5
B4
B3
B2
B1
B0
TDA9874A
Preliminary specification
15
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
17
18
FUNCTION
6
B7
B6
B5
B4
B3
MUTI2S
B2
B1
B0
19
SDGS1
AVL1
AVL0
SDGS0
20
TVSM
CSM2
CSM1
CSM0
MOS1
MOS0
SSS1
SSS0
21
SYSCL1
SYSCL0
SYSOUT
I2SFORM
IS2OUT
22
TVSMIIS
ICSM2
ICSM1
ICSM0
ISS1
ISS0
23
B3
B2
B1
B0
B0
24
MDGS1
MDGS0
MDOS1
MDOS0
25
255
FILTBW1
FILTBW0
IDMOD1
IDMOD0
EPB3
EPB2
EPB1
EPB0
MUTSOUT MUTMOUT
0
SDOS1
SDOS0
Philips Semiconductors
28
1999 Dec 03
DATA
SUBADDRESS
(DECIMAL)
Preliminary specification
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
If the Automatic Gain Control (AGC) function is switched off in the general configuration register (see Section 10.3.3) the
contents of this register defines a fixed gain of the SIF input stage. The input voltages given are meant to generate a
nearly full-scale output from the SIF ADC. If the AGC is on, the AGC gain setting is ignored. After switching off the AGC
function, the latest gain control setting is copied to the AGC gain register. If the AGC input level shift bit (AGCLEV) is set
to HIGH the input signal is scaled with 10 dB. The AGCLEV bit is also active if the AGC function is enabled.
The default setting after power-on reset is 0000 0000.
In Table 16 the stated step number corresponds with the SIF level read from subaddress 7 (see Section 10.4.6); the input
voltages should be considered as approximate target values.
Table 14 AGC gain register (subaddress 0)
7
AGCLEV
AGCB4
AGCB3
AGCB2
AGCB1
AGCB0
NAME
AGCLEV
AGCB4
AGCB3
AGCB2
AGCB1
AGCB0
1999 Dec 03
DESCRIPTION
If the AGC input level shift bit AGCLEV is set to HIGH the input signal is scaled with
10 dB. The AGCLEV bit is also active if the automatic gain function is enabled.
If the automatic gain control function is switched off in the general configuration register,
the contents of this register will define a fixed gain of the AGC stage.
29
Philips Semiconductors
Preliminary specification
TDA9874A
AGCLEV
AGCB4
AGCB3
AGCB2
AGCB1
0/1
0.0
333/1052
0/1
0.8
304/963
0/1
1.5
278/881
0/1
2.3
255/806
0/1
3.1
233/737
0/1
3.9
213/674
0/1
4.6
195/617
0/1
5.4
178/564
0/1
6.2
163/516
0/1
7.0
149/472
0/1
7.7
136/432
0/1
8.5
125/395
0/1
9.3
114/361
0/1
10.1
104/330
0/1
10.8
96/302
0/1
11.6
87/276
0/1
12.4
80/253
0/1
13.2
73/231
0/1
13.9
67/212
0/1
14.7
61/194
0/1
15.5
56/177
0/1
16.3
51/162
0/1
17.0
47/148
0/1
17.8
43/135
0/1
18.6
39/124
0/1
19.4
36/113
0/1
20.1
33/104
0/1
20.9
30/95
0/1
21.7
27/87
0/1
22.5
25/79
0/1
23.2
23/73
0/1
24.0
21/66
1999 Dec 03
30
AGC GAIN
MAX. SIF INPUT
(dB)
VOLTAGE
(mV; RMS)
AGCB0
Philips Semiconductors
Preliminary specification
TDA9874A
P2OUT
P1OUT
STDBY
INIT
CLRPFR
AGCSLOW
AGCOFF
SIFSEL
SYMBOL
DESCRIPTION
P2OUT
P1OUT
General purpose I/O pins 1 and 2: these bits control the general purpose input/output
pins. The contents of these bits is written directly to the corresponding pins. If an input is
desired, the bits must be set HIGH to allow the pins to be pulled LOW externally. Input
from the pins is reflected in the device status register (see Section 10.4.1). P1OUT is
recommended to be used for switching an SIF trap for the adjacent picture carrier in
designs that employ such a trap.
STDBY
Standby mode on/off: when STDBY = 1 the TDA9874A is set to the standby mode.
Most functions are disabled and power dissipation is somewhat reduced. When
STDBY = 0, the TDA9874A is in its normal mode of operation. On return from standby
mode, the device is in its Power-on reset mode and needs to be reinitialized with data
defined by the user.
INIT
CLRPFR
Clear power failure register: when CLRPFR = 1 it resets the clear power failure
register. This bit is automatically reset to CLRPFR = 0 after bit PFR in the device status
register has been read.
AGCSLOW
AGC decay time: when AGCSLOW = 1 a longer decay time and larger hysteresis are
selected for input signals with strong video modulation (conventional intercarrier). This
bit has only an effect, when bit AGCOFF = 0. When AGCSLOW = 0, it selects normal
attack and decay times for the AGC and a small hysteresis.
AGCOFF
AGC on/off: when AGCOFF = 1 it forces the AGC block to a fixed gain as defined in the
AGC gain register (see Section 10.3.2). When AGCOFF = 0, the AGC function is
enabled and the contents of the AGC gain register are ignored.
SIFSEL
1999 Dec 03
SIF input select: when SIFSEL = 1 it selects pin SIF2 for input (recommended for
satellite tuner). When SIFSEL = 0, pin SIF1 (recommended for terrestrial TV) is
selected.
31
Philips Semiconductors
Preliminary specification
TDA9874A
This register is used to define the signal source (the level of which is to be monitored) and the signal channel. Data can
be monitored e.g. before or after the DC filter at the FM/AM demodulator outputs. The peak level of signals can also be
observed. The last available data sample can be read out in the I2C-bus slave transmitter mode (see Section 10.4.5).
Phase means the differentiated phase output of the FM demodulator and is provided when the demodulator operates in
FM mode. The magnitude is supplied in AM mode.
The default setting after power-on reset is 0000 0000.
Table 19 Monitor select register (subaddress 2)
7
PEAK
MCSM1
MCSM0
MSS1
MSS0
SYMBOL
DESCRIPTION
PEAK
Peak level select: when PEAK = 1 it selects the rectified peak level of a source to be
monitored. Peak level value is reset to logic 0 after read-out (see read registers
5 and 6). After changing the monitor signal source for peak calculation it is advisable to
ignore the first read-out value due to stored data from previous calculations.
MCSM1
MCSM0
MSS1
MSS0
MCSM0
0
1
1999 Dec 03
SIGNAL CHANNEL
MSS1
MSS0
CH1 + CH2
-----------------------------2
DC output of FM/AM
demodulator
CH1
CH2
magnitude/phase output
of FM/AM demodulator
32
SIGNAL SOURCE
Philips Semiconductors
Preliminary specification
TDA9874A
where:
data = 24-bit frequency control word
f mix
24
data = -------- 2
f clk
B7
B6
B5
B4
B3
B2
B1
B0
B7
B6
B5
B4
B3
B2
B1
B0
B7
B6
B5
B4
B3
B2
B1
B0
10.3.6
This register should not be used when applying ESP. The format is the same as for sound carrier 1, except
subaddresses 6 to 8 are used. Subaddress 6 holds the high byte.
If the C2FR is used, it will be for either the second FM sound carrier of a terrestrial or satellite FM program or the NICAM
sound carrier.
1999 Dec 03
33
Philips Semiconductors
Preliminary specification
TDA9874A
This register should not be used when applying ESP. The default setting after power-on reset is 0000 0000.
Table 26 Demodulator configuration register (subaddress 9)
7
IDMOD1
IDMOD0
IDAREA
FILTBW1
CH2MOD1
CH2MOD0
FILTBW0
CH1MODE
SYMBOL
DESCRIPTION
IDMOD1
IDMOD0
IDAREA
FILTBW1
CH2MOD1
CH2MOD0
FILTBW0
CH1MODE
Identification mode for FM sound: these bits define the integrator time of the FM
identification. A valid result may be expected after twice this time has expired, at the
latest. The longer the time, the more reliable the identification; see Table 28.
Channel 2 receive mode: these bits control the hardware for the second sound carrier
in accordance with Table 29. The NICAM mode employs a wider bandwidth of the
decimation filters than the FM mode.
selects filter bandwidth in accordance with Table 30
Channel 1 receive mode: when CH1MODE = 1 it selects the hardware for the first
sound carrier to operate in AM mode. When CH1MODE = 0 the FM mode is assumed.
This applies to both terrestrial and satellite FM reception.
IDMOD0
IDENTIFICATION MODE
slow
medium
fast
CH2MOD0
FM
AM
NICAM
1999 Dec 03
CHANNEL 2
34
Philips Semiconductors
Preliminary specification
TDA9874A
FILTBW0
FILTER MODES
CHANNEL 1
CHANNEL 2
narrow
narrow
extra wide
narrow
medium
medium
wide
wide
Note
1. It is recommended to switch the FM sound mode identification off whenever the received program is not a terrestrial
2-carrier sound. Switching the identification off will reset the associated hardware to a defined state.
10.3.8
This register should not be used when applying ESP. This register is used to select the proper de-emphasis
characteristics as appropriate for the standard of the received carrier. Bits 3 to 0 apply to sound carrier 1, bits 7 to 4 apply
to sound carrier 2. In the event of A2 reception, both groups must be set to the same characteristics.
The default setting after power-on reset is 0000 0000.
Table 31 FM De-emphasis register (subaddress 10)
7
ADEEM2
FMDSC23
FMDSC22
FMDSC21
ADEEM1
FMDSC13
FMDSC12
FMDSC11
SYMBOL
DESCRIPTION
ADEEM2
FMDSC23
FMDSC22
FM de-emphasis: the state of these 3 bits determines the FM de-emphasis for sound
carrier 2; see Table 33.
FMDSC21
ADEEM1
FMDSC13
FMDSC12
FM de-emphasis: the state of these 3 bits determines the FM de-emphasis for sound
carrier 1; see Table 33.
FMDSC11
1999 Dec 03
35
Philips Semiconductors
Preliminary specification
TDA9874A
Table 33 De-emphasis
FMDSC23; FMDSC13
FMDSC22; FMDSC12
FMDSC21;FMDSC11
DE-EMPHASIS(1)
50 s
60 s
75 s
J17(2)
off
Notes
1. The FM de-emphasis gain is 0 dB at 40 Hz.
2. Not used in any known terrestrial TV sound standard. NICAM de-emphasis is selected in the NICAM configuration
register; see Table 41.
10.3.9
This register is used to select the proper dematrixing characteristics as appropriate for the standard of the received
carrier and the related sound mode identification. For the dematrixing, it is assumed that the output from sound carrier 1
is on channel 1 input. Bits 3 to 6 are not used.
The default setting after power-on reset is 0000 0000.
Table 34 FM dematrix register (subaddress 11)
7
IDSWFM
FDMS2
FDMS1
FDMS0
SYMBOL
DESCRIPTION
IDSWFM
FDMS2
FDMS1
FDMS0
1999 Dec 03
Dematrixing characteristics select: the state of these 3 bits select the dematrixing
characteristics; see Table 36
36
Philips Semiconductors
Preliminary specification
TDA9874A
FDMS1
FDMS0
L OUTPUT
R OUTPUT
MODE
CH1
CH1
mono 1
CH2
CH2
mono 2
CH1
CH2
dual
CH2
CH1
dual swapped
2CH1 CH2
CH2
stereo Europe
CH1 + CH2
-----------------------------2
CH1 CH2
-----------------------------2
CH1 + CH2
CH1 CH2
stereo Korea 6 dB
stereo Korea
1999 Dec 03
L OUTPUT
R OUTPUT
CH1
CH1
Europe
2CH1 CH2
CH2
Korea
CH1 + CH2
CH1 CH2
CH1
CH2
37
Philips Semiconductors
Preliminary specification
TDA9874A
+15
+14
+13
+12
+11
+10
+9
+8
+7
+6
+5
+4
+3
+2
+1
not defined
10
11
12
13
14
15
1999 Dec 03
38
Philips Semiconductors
Preliminary specification
TDA9874A
+15
+14
+13
+12
+11
+10
+9
+8
+7
+6
+5
+4
+3
+2
+1
not defined
10
11
12
13
14
15
1999 Dec 03
39
Philips Semiconductors
Preliminary specification
TDA9874A
DCXOPULL
DCXOTEST
DOUTEN
AMSEL
NDEEM
AMUTE
SYMBOL
DESCRIPTION
DCXOPULL DCXO frequency select: selects DCXO lower or upper test frequency during DCXO
test mode. When DCXOPULL = 1 it sets the DCXO to the lower DCXO frequency. When
DCXOPULL = 0 it sets the DCXO to its higher frequency.
DCXOTEST DCXO test mode enable: when DCXOTEST = 1 it enables the DCXO test mode
(available only during FM mode). In this mode frequency pulling via DCXOPULL is
enabled. When DCXOTEST = 0 it enables normal operation.
DOUTEN
AMSEL
Auto-mute select: when AMSEL = 1 the auto-mute will switch between NICAM sound
and the analog mono input. This bit only has an effect when the auto-mute function is
enabled and when the DAC has been selected in the analog output select register
(see Section 10.3.18). When AMSEL = 0, the auto-mute will switch between NICAM
sound and the sound on the first sound carrier (i.e. FM mono or AM).
NDEEM
De-emphasis on/off: when NDEEM = 1 it switches the NICAM J17 de-emphasis off.
When NDEEM = 0 it switches the NICAM J17 de-emphasis on.
AMUTE
Auto-muting on/off: when AMUTE = 1 automatic muting is disabled. This bit only has
an effect when the second sound carrier is set to NICAM. When AMUTE = 0 it enables
the automatic switching between NICAM and the program on the first sound carrier (i.e.
FM mono or AM), depending on the NICAM bit error rate. The FM dematrix should be
set to the mono position or IDSWFM (subaddress 11) should be set.
Notes
1. The decision of whether auto-muting is permitted will be taken by the controlling microprocessor based on
information contained in the TDA9874As status registers. Thus, it depends on the strategy implemented in the
software whether the auto-mute function is in accordance with NICAM 728 ETS Revised for Data Applications or
any other preference.
2. The NICAM de-emphasis gain is 0 dB at 40 Hz.
3. The AMSEL bit has only an effect on the analog sound outputs (OUTL, OUTR and OUTM). With regard to the digital
sound output (I2S-bus), the auto-mute will only switch between NICAM and the first sound carrier.
4. The DCXO test mode is intended for checking the DCXO control range with the actually used PCB layout and crystal
type. During normal operation, the DCXO test mode should not be used.
1999 Dec 03
40
Philips Semiconductors
Preliminary specification
TDA9874A
+15
+14
+13
+12
+11
+10
+9
+8
+7
+6
+5
+4
+3
+2
+1
not defined
10
11
12
13
14
15
1999 Dec 03
41
Philips Semiconductors
Preliminary specification
B7
B6
B5
B4
B3
B2
B1
B0
TDA9874A
B7
B6
B5
B4
B3
B2
B1
B0
MUTI2S
MUTSOUT
MUTMOUT
SYMBOL
DESCRIPTION
MUTI2S
MUTSOUT
MUTMOUT
1999 Dec 03
42
Philips Semiconductors
Preliminary specification
TDA9874A
Table 49 AVL control mode
AVL1
AVL0
off or reset
short decay (2 s)
medium decay (4 s)
long decay (8 s)
AVL MODE
SDOS1
SDOS0
RIGHT
FM/AM
FM/AM
NICAM left
NICAM right
FM/AM
NICAM M1
FM/AM
NICAM M2
SDGS1 0
AVL
1
AVL
0
L+R
The -------------- position of the matrix applies only to the DAC
2
outputs, it is not available for analog input signals.
SDGS1
SDGS0
DAC GAIN
(dB)
1999 Dec 03
43
Philips Semiconductors
Preliminary specification
TDA9874A
TVSM
CSM2
CSM1
CSM0
MOS1
MOS0
SSS1
SSS0
SYMBOL
DESCRIPTION
TVSM
Auto-select function: for TV applications, only in combination with IDSWFM set HIGH.
If set HIGH switches the matrix automatically depending on the IDSTE, IDDUA bits for
FM and the S/MB, D/SB bits for NICAM (see Sections 10.4.1 and 10.4.2).
CSM2
CSM1
Output channel selection mode, stereo output: these 3 bits select the output
channel selection mode; see Table 53
CSM0
MOS1
MOS0
SSS1
SSS0
Signal source for mono output: these 2 bits select the signal source for the mono
output; see Table 54
Signal source for stereo output: these 2 bits select the signal source for the stereo
output; see Table 55
Table 53 Output channel selection mode for stereo output (TVSM = LOW)
CSM2
CSM1
CSM0
L OUTPUT
R OUTPUT
REMARK
L input
R input
L input
L input
R input
R input
R input
L input
L+R
-------------2
L+R
-------------2
MOS0
SIGNAL SOURCE
mono DAC
external input L
external input R
mono input
1999 Dec 03
SSS1
SSS0
DAC
reserved
external input
mono input
44
SIGNAL SOURCE
Philips Semiconductors
Preliminary specification
TDA9874A
Table 56 Auto-select function (TVSM = HIGH and IDSWFM = HIGH): FM mode/NICAM mode for stereo DAC
OUTPUT CHANNEL SELECTION
MODE
CSM2
AUTO-MUTE = HIGH
AND CH2MOD = 10
CSM1
CSM0
MONO
STEREO
DUAL
X(1)
M/M
L/R
A/A
FM/AM: M/M
M/M
L/R
B/B
FM/AM: M/M
Note
1. X = dont care.
Signal source selection bits SDOS1 and SDOS0 must be set to 0X for FM mode (including FM mode by switching if
auto-mute select is set LOW) or 01 for NICAM mode, when using the auto-select function.
10.3.19 DIGITAL AUDIO INTERFACE CONFIGURATION REGISTER (DAICONR)
The default setting after Power-on reset is 00000000.
Table 57 Digital Audio Interface Configuration Register (subaddress 21)
7
SYSCL1
SYSCL0
SYSOUT
I2SFORM
I2SOUT
SYMBOL
DESCRIPTION
these 3 bits are not used and should be set to logic 0
SYSCL1
SYSCL0
SYSOUT
System clock output on/off: when SYSOUT = 1 it enables the output of a system (or
master) clock signal at pin SYSCLK. When SYSOUT = 0, the output will be off, thereby
improving EMC performance.
I2SFORM
I2SOUT
I2S-bus output on/off: when I2SOUT = 1 it enables the output of serial audio data
(2 pins) plus serial bit clock and word select in a format determined by the I2SFORM bit.
The TDA9874A then is an I2S-bus master. When I2SOUT = 0, the outputs mentioned
will be 3-stated, thereby improving EMC performance.
System clock frequency select: these 2 bits select the frequency of the system clock;
see Table 59
1999 Dec 03
SYSCL0
SYSCLK OUTPUT
FREQUENCY
(MHz)
256fs
8.192
384fs
12.288
512fs
16.384
768fs
24.576
45
Philips Semiconductors
Preliminary specification
TDA9874A
TVSMIIS
ICSM2
ICSM1
ICSM0
ISS1
ISS0
SYMBOL
DESCRIPTION
TVSMIIS
Auto-select function: for TV applications, only in combination with IDSWFM set HIGH.
If set HIGH switches the matrix automatically depending on the IDSTE, IDDUA bits for
FM and the S/MB, D/SB bits for NICAM in transmitters subaddresses 0 and 1
(see Sections 10.4.1 and 10.4.2).
ICSM2
ICSM1
ICSM0
ISS1
ISS0
1999 Dec 03
Output channel selection mode: these 3 bits select the output channel selection
mode; see Table 62
46
Philips Semiconductors
Preliminary specification
TDA9874A
Table 62 Mode of the digital matrix for signal selection (TVSMIIS = LOW)
ICSM2
ICSM1
ICSM0
L OUTPUT
R OUTPUT
REMARK
L input
R input
L input
L input
R input
R input
R input
L input
L+R
-------------2
L+R
-------------2
not allowed
during use of high
deviation mode
ISS0
LEFT
RIGHT
FM/AM left
FM/AM right
NICAM left
NICAM right
FM/AM
NICAM M1
FM/AM
NICAM M2
Note
1. The auto-select function is available only if ISS1 and ISS0 are set to 00 or 01.
Table 64 Auto-select function (TVSMIIS = HIGH and IDSWFM = HIGH): FM mode/NICAM mode for I2S-bus output
I2S-BUS OUTPUT
ICSM1
ICSM0
MONO
STEREO
DUAL
X(1)
M/M
L/R
A/A
FM/AM: M/M
M/M
L/R
B/B
FM/AM: M/M
ICSM2
Note
1. X = dont care.
1999 Dec 03
47
Philips Semiconductors
Preliminary specification
TDA9874A
+15
+14
+13
+12
+11
+10
+9
+8
+7
+6
+5
+4
+3
+2
+1
not defined
10
11
12
13
14
15
1999 Dec 03
48
Philips Semiconductors
Preliminary specification
TDA9874A
The level adjustment for an FM source is determined by
the Channel 1 output level adjustment register
(subaddress 12) for mono/dual A, or by the Channel 2
output level adjustment register (subaddress 13) for
dual B, or by the NICAM output level adjustment register
(subaddress 15) if a NICAM source is selected.
L+R
In stereo mode -------------- is chosen automatically. Selecting
2
Language B (MDOS1, MDOS0 = 01 or 11) will only show
effect, while a dual transmission via FM A2 or NICAM is
being received.
MDGS1
MDGS0
MDOS1
MDOS0
MDGS0
MDOS1
MDOS0
L+R
FM/AM -------------- or mono/dual A
2
L+R
NICAM -------------- or mono/dual A
2
1999 Dec 03
49
Philips Semiconductors
Preliminary specification
TDA9874A
If ESP is not used, the ESP register should not be
accessed in the refresh routine.
FILTBW1
FILTBW0
IDMOD1
IDMOD0
EPB3
EPB2
EPB1
EPB0
EPB2
EPB1
EPB0
NUMBER
NAME
A2, B/G
A2, M (Korea)
NICAM, I
NICAM, B/G
NICAM, D/K
NICAM, L
reserved
10
reserved
11
reserved
12
13
reserved
14
reserved
15
reserved
1999 Dec 03
50
Philips Semiconductors
Preliminary specification
TDA9874A
As a slave transmitter, the TDA9874A provides 12 registers with status information and data, a part of which is for Philips
internal purposes only. Each register is accessed by means of a subaddress.
Detailed descriptions of the slave transmitter registers are given in Sections 10.4.1 to 10.4.9.
Reading of data can start at any valid subaddress. It is allowed to read more than 1 data byte per transmission from the
TDA9874A. In this case, the subaddress is automatically incremented after each data byte, resulting in reading the
sequence of data bytes from successive register locations, starting at SUBADDRESS.
Each data byte in a read sequence, except for the last one, is acknowledged with Am. The subaddresses wrap around
from decimal 255 to 0. If an attempt is made to read from a non-existing subaddress, the device will send a data pattern
of all ones, i.e. FF in hexadecimal notation.
Table 71 General format for reading data from the TDA9874A
S SLAVE ADDRESS 0 A SUBADDRESS A Sr SLAVE ADDRESS 1 A
DATA
NAm P
FUNCTION
START condition
SLAVE ADDRESS
SUBADDRESS
Sr
DATA
NAm
Am
STOP condition
1999 Dec 03
51
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
P2IN
P1IN
RSSF
AMSTAT
VDSP
IDDUA
IDSTE
PFR
C4
C3
C2
C1
OSB
CFC
S/MB
D/SB
NICAM status
B7
B6
B5
B4
B3
B2
B1
B0
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
OVW
SAD
CI1
CI2
AD10
AD9
AD8
B7
B6
B5
B4
B3
B2
B1
B0
B7
B6
B5
B4
B3
B2
B1
B0
FUNCTION
0
IDPILOT
B4
B3
B2
B1
B0
SIF level
252
B7
B6
B5
B4
B3
B2
B1
B0
test register 2
253
B7
B6
B5
B4
B3
B2
B1
B0
test register 1
254
B7
B6
B5
B4
B3
B2
B1
B0
255
B7
B6
B5
B4
B3
B2
B1
B0
52
Note
1. Registers from subaddress 252 to 255 are for Philips internal purposes only. They are considered as a set of registers for the identification of
individual members and some key parameters in a family of devices.
Philips Semiconductors
DATA
SUBADDRESS
(DECIMAL)(1)
1999 Dec 03
Preliminary specification
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
P2IN
P1IN
RSSF
AMSTAT
VDSP
IDDUA
IDSTE
PFR
SYMBOL
DESCRIPTION
P2IN
Input from Port 2: this bit reflects the status of the P2 general purpose port pin;
see Section 10.3.3. If P2IN = 1, then the P2 general purpose port pin is HIGH.
If P2IN = 0, then the P2 general purpose port pin is LOW.
P1IN
Input from Port 1: this bit reflects the status of the P1 general purpose port pin;
see Section 10.3.3. If P1IN = 1, then the P1 general purpose port pin is HIGH.
If P1IN = 0, then the P1 general purpose port pin is LOW.
RSSF
Reserve Sound Switching Flag: when RSSF = 1, this bit is a copy of the C4 bit in the
NICAM status register (see Section 10.4.2). It indicates that the FM (or AM for
standard L) sound matches the digital transmission and auto-muting should be enabled.
When RSSF = 0, auto-muting should be disabled, as analog and digital sound are
different.
AMSTAT
VDSP
IDDUA
IDSTE
PFR
Power failure register: the power supply for the digital part of the device (VDDD1) has
temporarily been lower than the specified lower limit. If this is detected an initialization of
the device has to be carried out to ensure reliable operation.
Auto-mute Status: if this bit is HIGH, it indicates that the auto-muting function has
switched from NICAM to the program of the first sound carrier (i.e. FM mono or AM in
NICAM L systems)
10.4.2
C4
C3
C2
C1
OSB
CFC
S/MB
D/SB
1999 Dec 03
53
Philips Semiconductors
Preliminary specification
TDA9874A
SYMBOL
DESCRIPTION
C4
C3
C2
C1
OSB
Synchronization bit: when OSB = 1, it indicates that the device has both frame and C0
(16 frame) synchronization. When OSB = 0, it indicates that the audio output from the
NICAM part is digital silence.
CFC
S/MB
D/SB
Identification of NICAM dual mono: when D/SB = 1, it indicates dual mono mode.
NICAM application control bits: these bits correspond to the control bits C1 to C4 in
the NICAM transmission.
Notes
1. The TDA9874A does not support the extended control modes. Therefore, the program of the first sound carrier
(i.e. FM mono or AM) is selected for reproduction in case bit C3 is set HIGH, independent of bit AMUTE in the NICAM
configuration register being set or not.
2. When a NICAM transmitter is switched off, the device will lose synchronization. In that case the program of the first
sound carrier is selected for reproduction, independent of bit AMUTE being set or not.
NICAM ERROR COUNT REGISTER (NIECR)
10.4.3
Bits B7 to B0 contain the number of errors occurring in the previous 128 ms period. The register is updated every
128 ms.
Table 79 NICAM error count register (subaddress 2)
7
B7
B6
B5
B4
B3
B2
B1
B0
10.4.4
The contents of these two registers provide information on the additional data bits. AD byte 0 is stored at subaddress 3.
Table 80 Data register 1 (subaddress 3)
7
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
SYMBOL
7 to 0
AD7 to AD0
DESCRIPTION
The lower 8 bits of the additional data word.
OVW
SAD
CI1
CI2
AD10
AD9
AD8
1999 Dec 03
54
Philips Semiconductors
Preliminary specification
TDA9874A
SYMBOL
DESCRIPTION
OVW
If this bit is HIGH, new additional data bits are written to the IC without the previous bits
being read.
SAD
When SAD = 1, new additional data is written into the IC. This bit is reset when the
additional data bits are read.
10.4.5
CI1
CI2
AD10
AD9
AD8
B7(1)
B6
B5
B4
B3
B2
B1
B0
IDPILOT
B4
B3
B2
B1
B0
BIT
SYMBOL
DESCRIPTION
IDPILOT
B4
Note
1. B7 is the most significant bit or sign bit of the word.
Table 85 Level read-out register B (subaddress 6)
7
B7
6
B6
5
B5
4
B4
3
B3
2
B2
B3
B1
B0(1)
B2
B1
B0
Note
1. B0 is the least significant bit of the word.
Note
10.4.6
1999 Dec 03
55
Philips Semiconductors
Preliminary specification
11 I2S-BUS DESCRIPTION
B7
B6
B5
B4
B3
B2
B1
B0
10.4.8
B7
B6
B5
B4
B3
B2
B1
B0
10.4.9
B7
B6
B5
B4
B3
B2
B1
B0
B7
B6
B5
B4
B3
B2
B1
B0
1999 Dec 03
TDA9874A
56
Philips Semiconductors
Preliminary specification
TDA9874A
SCK
WS
SDO
LSB
MSB
LSB
MSB
MGK759
one sample
a. MSB-aligned format.
SCK
WS
SDO
LSB
MSB
LSB
MSB
MGK758
one sample
b. I2S-bus format.
1999 Dec 03
57
Philips Semiconductors
Preliminary specification
TDA9874A
12 EXTERNAL COMPONENTS
handbook, full pagewidth
470 nF
EXTIR
42
MONOIN
470 nF
470 nF
47 F
EXTIL
Vref2
P2
2.2 F
OUTM
10
nF
2.2 F
OUTL
40
39
38
37
36
OUTR
35
34
10
nF
10
VDDA1
470
nF V
SSA1
VSSD1
VSSD3
Lx (2)
VDDD3
470 nF
3.3
+5 V
SYSCLK
SCK
WS
I2S-bus
SDO
SDA
I2C-bus
33
10
11
TDA9874APS
32
SCL
10
VDDA3
+5 V
470 nF
470
nF
+5 V
41
10
nF
2.2 F
+5 V
VSSA4
P1
VDDD1
Lx (2)
VSSD2
TP2
(1)
NICAM
TP1
(1)
PCLK
ADDR1
XTALO
24.576
MHz
XTALI
TEST2
(1)
12
31
13
30
14
29
VSSA3
CRESET
SIF1
28
15
Vref1
SIF2
16
27
17
26
18
25
19
24
20
23
21
22
1 F
47 pF
50
100 nF
47 pF
50
TEST1
(1)
VDEC
decoupling
capacitor
470 nF
VSSA2
ADDR2
Iref
8.2 k
MHB591
All analog and digital supply ground pins are connected internally and should be connected via a massive external ground plate.
(1) TP1, TP2, TEST1 and TEST2 should be connected to VSSD during normal operation.
(2) Lx: ferrite bead, e.g. BLM 31A601S (Murata).
1999 Dec 03
58
Philips Semiconductors
Preliminary specification
TDA9874A
+5 V
OUTL
42
41
470
nF
40
39
38
VDDD3
VSSD3
37
SYSCLK
Lx (2)
P1
EXTIR
EXTIL
Vref2
P2
43
470
nF
36
35
34
33
32
31
30
29
SCK
10
nF
2.2 F
+5 V
OUTM
VSSA4
44
2.2 F
470
nF
MONOIN
47
F
2.2 F
3.3
470
nF
OUTR
10
nF
10
VDDA1
470
nF V
SSA1
WS
I2S-bus
SDO
SDA
I2C-bus
VSSD1
470
nF
+5 V
VDDD1
Lx (2)
28
TP2
(1)
NICAM
27
26
25
10
24
11
23
VSSA3
CRESET
SIF1
TP1
(1)
21
Vref1
SIF2
470 nF
8.2 k
24.576
MHz
(1)
decoupling
capacitor
(1)
MHB592
All analog and digital supply ground pins are connected internally and should be connected via a massive external ground plate.
(1) TP1, TP2, TP3, TEST1 and TEST2 should be connected to VSSD during normal operation.
(2) Lx: ferrite bead, e.g. BLM 31A601S (Murata).
1999 Dec 03
59
1 F
47 pF
100 nF
50
47 pF
50
22
TEST1
20
VDEC
19
VSSA2
18
ADDR2
17
Iref
16
TEST2
15
TP3
14
XTALI
13
XTALO
PCLK
12
ADDR1
(1)
+5 V
470 nF
VSSD2
n.c.
10
VDDA3
TDA9874AH
SCL
Philips Semiconductors
Preliminary specification
TDA9874A
13 PACKAGE OUTLINES
seating plane
SOT270-1
ME
A2
A1
c
e
b1
(e 1)
w M
MH
b
22
42
pin 1 index
E
21
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
min.
A2
max.
b1
D (1)
E (1)
e1
ME
MH
Z (1)
max.
mm
5.08
0.51
4.0
1.3
0.8
0.53
0.40
0.32
0.23
38.9
38.4
14.0
13.7
1.778
15.24
3.2
2.9
15.80
15.24
17.15
15.90
0.18
1.73
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
90-02-13
95-02-04
SOT270-1
1999 Dec 03
EUROPEAN
PROJECTION
60
Philips Semiconductors
Preliminary specification
TDA9874A
QFP44: plastic quad flat package; 44 leads (lead length 2.35 mm); body 14 x 14 x 2.2 mm
SOT205-1
c
y
X
33
23
34
22
ZE
e
E HE
A2
(A 3)
A1
wM
bp
Lp
pin 1 index
44
12
detail X
1
11
ZD
v M A
wM
bp
D
HD
v M B
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
D (1)
E (1)
HD
HE
Lp
mm
2.60
0.25
0.05
2.3
2.1
0.25
0.50
0.35
0.25
0.14
14.1
13.9
14.1
13.9
19.2
18.2
19.2
18.2
2.35
2.0
1.2
0.3
0.15
0.1
Z D (1) Z E (1)
2.4
1.8
2.4
1.8
7
0o
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
SOT205-1
133E01A
1999 Dec 03
JEDEC
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
95-02-04
97-08-01
61
Philips Semiconductors
Preliminary specification
14 SOLDERING
14.1
Introduction
14.3.2
14.2.1
MANUAL SOLDERING
14.3.3
MANUAL SOLDERING
1999 Dec 03
WAVE SOLDERING
TDA9874A
Philips Semiconductors
Preliminary specification
TDA9874A
PACKAGE
WAVE
suitable(2)
Surface mount
REFLOW(1)
DIPPING
suitable
BGA, SQFP
not suitable
suitable
not suitable(3)
suitable
PLCC(4),
suitable
SO, SOJ
suitable
not
recommended(4)(5)
suitable
not
recommended(6)
suitable
Notes
1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum
temperature (with respect to time) and body size of the package, there is a risk that internal or external package
cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the
Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods.
2. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.
3. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink
(at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version).
4. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction.
The package footprint must incorporate solder thieves downstream and at the side corners.
5. Wave soldering is only suitable for LQFP, QFP and TQFP packages with a pitch (e) equal to or larger than 0.8 mm;
it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
6. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is
definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
1999 Dec 03
63
Philips Semiconductors
Preliminary specification
TDA9874A
15 DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
16 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
17 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1999 Dec 03
64
Philips Semiconductors
Preliminary specification
1999 Dec 03
65
TDA9874A
Philips Semiconductors
Preliminary specification
1999 Dec 03
66
TDA9874A
Philips Semiconductors
Preliminary specification
1999 Dec 03
67
TDA9874A
Internet: http://www.semiconductors.philips.com
SCA 68
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
545004/01/pp68
Dec 03