Professional Documents
Culture Documents
Spreader Bar With Lugs
Spreader Bar With Lugs
htm
HELP FILE FOR: DESIGN PROGRAM FOR SPREADER BARS WITH LUGS TOP AND BOTTOM:
DEFINITION:
This program can be used to design spreader bars fabricated from structural members such as pipe, square tube or beams
(beams that are non-compact/compact with their lengths less than Lu). It is left to the user to verify that any beam
selected meets the non-compact, compact and Lu criteria as presented in the appendix below. These are spreader
bars that have two lugs located above the structural member and two or more lugs located below the structural member. It
is also applicable to spreader bars where the CG of the load does not hang under the center of the bar. In this case, the CG
will be located on a point on the bar that is defined by a vertical plumb line that runs down from the hook thru the CG of
the load. Again, this is not necessarily the center of the bar.
This program can also be used to design spreader bars that have the top lug holes located on the centerline of the bar, ie,
Versa Bars, etc. In this case, set the vertical distance from the centerline of the bar to the centerline of the top lug holes to
zero.
PROGRAM OBJECTIVE:
The objective of this program is to help the spreader bar designer develop a design that is efficient and safe. It can also
be used to check the design of an existing spreader bar. The output information conforms to the requirements of AISC
and ASME B30.20. The program also provides the tensions for the lifting slings and their lengths, i.e., the rigging hook
up.
Refer to the examples at the end of this help file for design tips.
PRE-DESIGNED LIFTING LUG DETAILS:
Details for pre-designed lifting lugs can be found by clicking on the Lug button on the input/output screen of the program.
WHAT THE PROGRAM DOES NOT DO:
This program does not design the lifting lugs or size the welds to connect the lugs to the spreader bar. The lugs and welds
must be designed using one of the lug design programs in the same design section of this website. One lug program
designs pad eye type lifting lugs and the other one designs plate type lifting lugs.
It is recommended that the lugs be designed before the spreader bar is designed so that the distance from the centerline of
the top lugs to the centerline of the spreader bar will be known. Otherwise, a conservative guess will have to be made
and latter verified. See Quiz 26 for a sample lug design.
It is recommended that lifting lugs similar to the ones shown in the elevation view, the sketch below or the photo be
used. By slotting the pipe, square tube or beam flanges, the lugs can be inserted into the slots and welded on with fillet
welds. Usually a fillet weld smaller than the thickness of the pipe wall, square tube wall or the flange/web of the beam
can be used, which will be much smaller than butt welds required to attach the same capacity pad eye lugs. Attaching the
lugs in this fashion is much safer than using pad eye lugs with butt welds.
1 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
. Note the dashed lines in the sketch above, which indicate lines of force from the slings. When these lines meet at the
centerline of the spreader bar, there is zero moment in the spreader bar due to the influence of the slings.
Note that there are two top lugs in the photo, one on either side of the beam web
ASME B30.20 requires that all spreader bars be marked with the Manufacturers name, the serial number of the bar, the
weight of the bar and the rated load. It is recommended that the rated load be based on a specific sling angle and that
sling angle be listed as the fifth item on the tag.
UNITS CONVERSIONS:
To convert from kips to metric tons (Te), divide the kips by 2.2046
To convert from pound/feet to kg/m, multiply the lb/feet by 1.4882
To convert from kip-in. to Te-cm, multiply the kip-in. by 1.1521
To convert from ksi to Te/cm^2, divide the ksi by 14.2231
To convert from inches to centimeters, multiply the inches by 2.54
To convert from in^2 to cm^2, multiply the in^2 by 6.45
To convert from in^3 to cm^3, multiply the in^3 by 16.39
To convert from in^4 to cm^4, multiply the in^4 by 41.62
TOTAL LOAD:
2 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
The total load is the combined weight of the load and any items that might be included for erection, i.e., trays, insulation,
piping, platforms & ladders, fire proofing, weight contingency, rigging, etc. It is input as either kips (1 kip = 1,000 lbs.)
or metric tons (Te).
ANGLE OF THE LEFT SLING:
When the CG of the load does not hang under the center of the spreader bar, different lengths of slings must be used to
keep the hook centered over the CG. Use the smaller of the two sling angles for the input value for the left sling. It is
recommended that all sling angles be kept at 60 degrees or greater. The program will calculate the angle of the right sling.
HORIZONTAL DISTANCE, BEARING TO BEARING ON DUPLEX CRANE HOOK.
This horizontal distance is measured from the center of the bearing area on one prong to the center of the other prong. If
a load block with a single hook is being used, enter zero for this value. See the elevation view of the spreader bar and
rigging.
LENGTH OF THE SPREADER BAR, overall:
The overall length of the spreader bar is measured from one end of the spreader bar to the other end. This distance is
only used in figuring the bending in the spreader bar due to its own weight.
STRUCTURAL MEMBERS:
In using this program, only the following structural shapes can be used as the main horizontal member for a spreader bar:
a.
b.
c.
Pipe
Square tubing
Beams, non-compact or compact whose lengths are less than Lu. It is left to the user to determine if the beam
being considered is non-compact or compact and its length is less than Lu. See explanation of Lu in appendix
below
The properties of some structural shapes are included in the lookup table in the program. The user can select a structural
shape and the properties will be imported into the appropriate fields of the program.
Note: The Lu of the beams listed in the lookup table is based on a Yield Stress (Fy) of 36 ksi. See Lu below on how to
treat Lu for a 50 ksi beam.
If a structural shape is not listed that the user would like to consider, then the user can click on the SHAPES button, input
the shape description, for example Beam W12x64, and then input its properties directly into the fields of the program.
The American Institute of Steel Construction (AISC) lists all available shapes and their ENGLISH units. For structural
shapes with properties listed in METRIC units, the user will have to refer to other sources.
3 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
A minimum impact factor of 1.80 should be used for new design in order to conform to ASME B30.20, which limits
stresses to .33*Fy. By using 1.80, the allowable stresses can be used as printed in the AISC Manual.
The program allows a variable impact factor to be used so that when checking an existing design, the impact factor can
be determined that was used to calculate the stated allowable load for the spreader bar. If the impact factor turns out to be
less than 1.8, the program user will then have to make a decision as to the structural integrity of the spreader bar based on
the actual impact factor, its application and the risk involved.
The impact factor is limited to 1.25 or greater. If an impact factor less than 1.25 is used, the program shows error in all
of the output fields and a message is displayed stating that the impact factor is less than 1.25.
The impact factor is included in the output value for the combined stress check. It is not included in any other output
values.
Lu: (For Beams Only)
The program checks Lu against the distance between the top lugs and against the distance between the bottom lugs. The
program considers the largest of these distances the length of the spreader bar, not the overall length. If Lu is less than
either of these distances, the program shows error in all of the output fields and a message is displayed showing the
length compared and asks the user to select a beam with a larger Lu.
For the beams in the lookup table, Lu is based on a Yield Stress (Fy) of 36 ksi. If the program user wants to use a 50-ksi
beam, the properties in the look up table are still applicable. The user only needs to enter the correct Lu for 50 ksi, and
change the Fy field to read 50 ksi, i.e., for a W18 x 119, Lu = 29.1 for Fy = 36 ksi, but Lu = 21.0 for Fy = 50 ksi.
DISTANCE FROM THE CG TO THE TOP LEFT LUG FOR ZERO MOMENT DUE TO ANGLE OF TOP LEFT
SLING:
The program calculates this distance by using the left sling angle entered and it can be used to locate the left top lug. The
user can input the distance back in to the program so that the extended line of the sling angle will intersect the horizontal
centerline of the spreader bar above the vertical centerline of the lower left lug, thus ensuring that there is zero moment in
the spreader bar from the influence of the sling.
DISTANCE FROM THE CG TO THE TOP RIGHT LUG FOR ZERO MOMENT DUE TO ANGLE OF TOP RIGHT
SLING:
The program calculates this distance by using the right sling angle and it can be used to locate the top right lug. The user
can input it back in to the program so that the extended line of the sling angle will intersect the horizontal centerline of
the spreader bar above the vertical centerline of the lower right lug, thus ensuring that there is zero moment in the
spreader bar from the influence of the sling.
KL/R:
The program uses a slenderness ratio (kl/r) equal to a maximum of 120. If this maximum is exceeded, error will show
in all of the output fields. A message will be displayed that asks the user to increase the member size in order to reduce
the kl/r down below 120.
The length of the spreader bar (l) used to calculate kl/r is the distance between the top lug holes or the distance between
the bottom lug holes, which ever is the greater distance.
MOMENT DUE TO THE COMPRESSIVE FORCE IN THE SPREADER BAR AND THE OFFSET OF THE TOP
LUGS:
This moment can be negative or positive. A negative value indicated that the spreader bar is being bowed up at the
centerline. The user can use this negative value to good use by balancing out the positive moments of the other bending
moments, so that the net bending moment can be zero or slightly negative. This provides the maximum capacity for the
spreader bar. See examples 2 & 4.
A negative moment occurs when the sling angles are higher than the ones that cause zero bending moment in the spreader
bar.
NET BENDING MOMENT IN THE BAR:
4 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
The net bending moment can also be negative or positive for the same reason as given above.
AXIAL AND BENDING STRESSES:
The program checks the actual axial stress (fa) against the allowable axial stress (Fa). If fa > Fa, then error will show in all of
the output fields. A message is displayed, asking the user to reduce this stress. It makes the same check for the bending stress.
5 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
these values for the same dimensions back into the input section and note that the moment due to the compression force
changes from 248.14 Te-cm to 16.88 Te-cm and the combined stress check changes from 0.92 to 0.71.
Next change the angle of the left sling from 68 degrees to 69 degrees and note that the moment due to the compression
force changes to 89.53 Te-cm and the combined stress check changes to 0.58. The negative 89.53 indicates that the
spreader bar is being bowed up in the center and this moment is counteracting the moment due to the weight of the
spreader bar. The net moment is now 24.22 Te-cm.
Now change the pipe size from a 45.72 x 0.953 wall to a 35.56 x 0.953 wall and note that the combined stress is 0.80.
Therefore, a pipe size of 35.56 x 0.953 would also work after fine-tuning the design per the above paragraph.
Now change the pipe size back to a 45.72 x 0.953 and increase the load to 498.96 Te and note that the combined stress
check is 0.99. An increase in load capacity of 498.96/294.84 = 169 %
APPENDIX:
This appendix contains reference material from the American Institute of Steel Construction (AISC) giving the definition of
compact beams, non-compact beams and beams with lengths equal to but not greater than Lu where Lu is the maximum
unbraced length of the compression flange at which the allowable bending stress may be taken at 0.6*Fy.
The example used is a W14 x 82 wide flange beam where:
Rt = 2.74 inches
Lu
Lu = 28.1 feet
Compact beam
Non-compact beam
Limiting W/t ratios
Rt
Formulas F1-6 & 8
Rt
6 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
7 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
8 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
9 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
10 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
11 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
12 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
13 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
14 of 15
3/13/2013 2:39 PM
http://www.maximumreach.com/SB1Help14Sep06.htm
15 of 15
3/13/2013 2:39 PM