CASEIN PRODUCTS

Casein is the principal protein found in cows milk from which it has been extracted
commercially for most of the 20th century. It is responsible for the white, opaque
appearance of milk in which it is combined with calcium and phosphorus as clusters of
casein molecules, called micelles.
The major uses of casein until the 1960s were in technical, non-food applications such as
adhesives for wood, in paper coating, leather finishing and in synthetic fibres, as well as
plastics for buttons, buckles etc. During the past 30 years, however, the principal use of
casein products has been as an ingredient in foods to enhance their physical (so-called
functional) properties, such as whipping and foaming, water binding and thickening,
emulsification and texture, and to improve their nutrition.
In New Zealand, casein is precipitated from the skim milk that is produced after
centrifugal separation of whole milk. The skim milk may be acidified to produce acid
casein or treated with an enzyme, resulting in the so-called rennet casein. The precipitated
casein curd is separated from the whey, washed and dried. Water-soluble derivatives of
acid caseins, produced by reaction with alkalis, are called caseinates.

INTRODUCTION
The amount of casein in cows whole milk varies according to the breed of cow and stage of
lactation, but is generally in the range 24-29 g L-1. Casein contains 0.7-0.9% phosphorus,
covalently bound to the protein by a serine ester linkage. Casein is consequently known as a
phospho-protein. All the amino acids that are essential to man are present in casein in high
proportions, with the possible exception of cysteine. Thus, casein may be considered as a
highly nutritious protein.
Casein exists in milk in complex groups of molecules (sometimes referred to as calcium
phospho-caseinate) that are called micelles. The micelles consist of casein molecules,
calcium, inorganic phosphate and citrate ions, and have a typical molecular weight of several
hundred million. In terms of physical chemistry, the casein micelles may be considered to
exist in milk as a very stable colloidal dispersion. The caseins, as proteins, are made up of
many hundreds of individual amino acids, each of which may have a positive or a negative
charge, depending on the pH of the [milk] system. At some pH value, all the positive charges
and all the negative charges on the [casein] protein will be in balance, so that the net charge
on the protein will be zero. That pH value is known as the isoelectric point (IEP) of the
protein and is generally the pH at which the protein is least soluble. For casein, the IEP is
approximately 4.6 and it is the pH value at which acid casein is precipitated. In milk, which
has a pH of about 6.6, the casein micelles have a net negative charge and are quite stable.
Although casein has been shown to consist of several individual casein components, referred
to as s1-, s2-, - and -casein, each having slightly different properties (which are caused
by small variations in their amino acid content), only the commercial product, which contains
all of these components, is considered in this article.

III-Dairy-E-Casein-1

EXTRACTION OF CASEIN FROM MILK

Separation
Casein is extracted from milk using the processes outlined in Figures 1 and 2. Whole cows
milk (with a typical fat content of 4.65% - see Figure 1 in the introductory article) is first
separated by means of centrifuges that produce cream (for the manufacture of butter or other
milkfat products - see the article on milkfat products) and skim milk. Skim milk can thus be
considered as the raw material from which casein products are made.
Precipitation
The operations involved in the precipitation of casein in New Zealand are shown in Figure 1.
Precipitation by means of acidification can be considered in terms of simple chemistry as
follows, R being the casein protein:
H2N-R-COO- + H+
casein micelle
(pH = 6.6)
Colloidal dispersion

H3N-R-COOacid casein
(pH = 4.6)
Insoluble particles

In the case of enzyme coagulation of casein, there is no change in the pH of the milk. Instead,
the addition of a specific enzyme, chymosin, which is found in the stomach of newborn
calves, specifically cleaves a highly charged portion from the -casein, called
glycomacropeptide. That action causes the remainder of the -casein (now called para-casein) to lose its considerable power in stabilising the micelles in milk, and the result is the
formation of a three-dimensional gel network or clot of the casein in the presence of calcium
ions. This reaction is essential in the manufacture of virtually all cheese types and in the
production of rennet casein.
Wet-processing operations
When the casein has been precipitated, the mixture is heated (a process known in the dairy
industry as cooking). Heating of the precipitated casein causes the particles to shrink and
expel moisture (whey) (rather like a sponge), and also to agglomerate together to form
clumps of curd. The curd is then separated from the whey and washed several times with
water in vats prior to mechanical dewatering by pressing or centrifuging.
Drying and dry processing of casein
The dewatered curd, with a moisture content of about 55%, is dried by means of hot air using
either fluidised bed driers with multiple decks or pneumatic-conveying ring driers to produce
a dry casein having a moisture content of 10-12%. The warm, unmilled casein is then
subjected to several dry processing steps (Figure 2), including cooling (usually by air
conveying), tempering or conditioning to ensure that moisture is distributed evenly
between large and small particles, milling, sifting (to produce coarse, medium and fine mesh
particles), blending (to ensure uniformity) and bagging. The 25 kg bags of casein are placed
on pallets and stored ready for shipping.

III-Dairy-E-Casein-2

WHOLE MILK separation CREAM

CALF RENNET

SKIM MILK

LACTIC STARTER

pasteurisation

inoculation

inoculatinon

incubation

clotting

HYDROCHLORIC
OR SULPHURIC
ACID

precipitation

coagulation

'cooking'

'cooking'

'cooking'

RENNET
CASEIN CURD

MINERAL ACID
CASEIN CURD

LACTIC ACID
CASEIN CURD

RENNET
CASEIN WHEY
(pH 6.6)

MINERAL ACID
CASEIN WHEY
(pH 4.6)

LACTIC ACID
CASEIN WHEY
(pH 4.6)

Figure 1 - Processing steps involved in the precipitation of acid and rennet caseins from milk.

III-Dairy-E-Casein-3

CASEIN CURD + WHEY

WHEY

separation

CASEIN CURD

washing

WATER

DEWATERED CASEIN CURD

COOL AIR + MOISTURE

drying

HOT AIR

COOL AIR

CASEIN

tempering

milling

sieving

blending

sampling

bagging

BAGS (capacity 25 kg)

storage
Figure 2 -

III-Dairy-E-Casein-4

Processing operations in the washing and drying of caseins.

Types of casein
As indicated above, two basic types of casein - acid and rennet - are produced in New Zealand.
They are named in accordance with the coagulating agent employed. Three types of acid casein
are made commercially: lactic, hydrochloric and sulphuric acid caseins. In New Zealand, lactic
acid casein has been the most common casein product, although larger quantities of sulphuric
acid casein have been produced in recent years. In Australia and Europe, the most common
precipitant for acid casein is hydrochloric acid, which is a by-product of the chemical industry
and hence is relatively cheap. In New Zealand, however, which has a very small chemical
industry, hydrochloric acid is relatively expensive. On the other hand, sulphuric acid is relatively
cheap, being produced in comparatively large quantities by the fertiliser industry for use in the
manufacture of superphosphate. Consequently, virtually all mineral acid casein made in New
Zealand is precipitated using sulphuric acid. The properties of the different types of acid casein
are very similar and, for most applications, the acid caseins can be used interchangeably.
For the manufacture of rennet casein, several different coagulants are now available. These
include chymosin (previously known as rennet or rennet extract), the milk-clotting enzyme
extracted from the stomachs of young calves, and a number of so-called microbial rennets, which
are enzymes that have been produced by means of microbial fermentation techniques. The
caseins produced using any of these enzyme preparations are all known as rennet casein, and all
have similar properties. However, their properties are noticeably different from those of acid
casein.
Acid casein manufacture
Figure 1 outlines the steps involved in the precipitation of the acid caseins.
Lactic acid casein
For the manufacture of lactic acid casein, skim milk (pH 6.6) is first pasteurised (72oC for 15 s).
It is then cooled to setting temperature (22-26oC) and inoculated with several strains of lactic
acid-producing bacteria, known as starters (e.g. Lactococcus lactis sub-species cremoris, 0.10.2% of milk volume). The milk is incubated, without agitation, in large silos (each with a
capacity of up to 250 000 L) for a period of 14-16 h. During this period, some of the lactose in
the milk is converted to lactic acid by the starter (shown by a simple equation in Figure 3) and
the pH is reduced to about 4.6, causing coagulation of the casein (and the milk). This takes the
form of a soft gel and is generally referred to in the industry as coagulum or coag.
The fermentation of lactose to lactic acid in the manufacture of lactic acid casein is not as simple
as that shown in Figure 3, however, and a number of other compounds are produced as well, e.g.
diacetyl (CH3COCOCH3), acetoin (CH3CHOHCOCH3) and benzoin (C6H5COCHOHC6H5).
These are present in relatively small amounts and do not generally present any serious problems.
After the pH of the milk has reached 4.6-4.7, the coagulum is cooked (i.e. heated), usually by
means of a combination of indirect heating (through a heat exchanger) and steam injection, to a
temperature of 50-55oC. After a brief period of residence in a cooking line and acidulation
vat, the resultant curd is separated from the whey, washed and dried, as outlined above.

III-Dairy-E-Casein-5

C12H22O11 + H2O
Lactose
Figure 3 -

4 CH3CH(OH)COOH
Lactic acid

Simple equation showing the conversion of lactose to lactic acid.

Mineral acid casein

For the precipitation of mineral acid casein, pasteurised skim milk at a pH of 6.6 is mixed
thoroughly with dilute (0.25 mol L-1) acid at a temperature of about 20oC to a pH of
approximately 4.6. In this case, because of the very vigorous agitation and the short mixing
time, the casein is precipitated as very fine, individual particles in a liquid serum (whey),
unlike the gel/coagulum formed in lactic acid casein manufacture. The acidified milk mixture
is then cooked and processed further in a manner similar to that described for the production
of lactic acid casein.
Rennet casein manufacture
When rennet casein is made, the skim milk is not acidified. Hence, the pH remains at 6.6
throughout the manufacturing process. Following pasteurisation of the skim milk, it is cooled
to a setting temperature of about 29oC, and calf rennet or microbial rennet is added (ratio by
volume: 1 of rennet to about 7000 of skim milk) and mixed in thoroughly (Figure 1). During
the first stage of renneting, the enzyme specifically cleaves one of the bonds in -casein,
releasing part of the protein chain that is commonly referred to as glycomacropeptide. This
action destabilises the casein micelles and, in the second stage of the reaction, they form a
three-dimensional clot with some of the calcium ions that are present in the milk. The
renneting process usually takes place in a period of 20-40 min under the conditions (pH and
temperature) described above. The clotted milk may then be cooked and the casein processed
in a manner similar to that described for lactic acid casein.
Yield
The yield of commercial casein is about 3 kg/100 kg skim milk.
MANUFACTURE OF CASEINATES
Caseinates may be produced by reaction under aqueous conditions of acid casein curd or dry
acid casein with any one of several different dilute alkalis, as outlined in Figures 4 and 5.
+

H3N-R-COO- + OHacid casein

(pH = 4.6)
Insoluble particles

Figure 4 -

H2N-R-COO- + H2O
caseinate
(pH = 6.6)
Solution (Na, K or NH4 caseinates); or
Colloidal dispersion (Ca caseinate)

Simple equation showing the neutralisation of acid casein with

alkali (where R represents casein protein).

The resulting homogeneous solution may be spray dried to produce a caseinate powder
having a moisture content of 3-6%, depending on the manufacturing conditions and customer
requirements.

III-Dairy-E-Casein-6

Spray-dried sodium caseinate

The most common alkali used in the manufacture of spray dried sodium caseinate is sodium
hydroxide. It is mixed (as an aqueous solution with a typical concentration of 2.5 M) with a
slurry of the casein curd or powder in water. The usual amount of sodium hydroxide needed
is about 2% (w/w) of the casein solids.
The casein curd is milled (Figure 5) using one or more colloid mills to reduce the size of the
individual particles so that they will dissolve rapidly, and is then mixed with the alkali using
high shear. In producing solutions of sodium caseinate for spray drying, it is important to
achieve the maximum possible concentration of solids for economic reasons, as the more
water there is to evaporate, the higher is the energy cost. Concentrated solutions of sodium
caseinate (> 15% solids), however, are very viscous, and require powerful agitators and
pumps for mixing and fluid transfer. The use of high temperatures (60-95oC) during the later
dissolving stages is of practical benefit, as the viscosity of sodium caseinate solutions
decreases with temperature. However, there is still a delicate balance between what is
mechanically achievable and what is economically practicable during the commercial
production of sodium caseinate.
Other caseinates
The manufacture of potassium and ammonium caseinates is very similar to that of sodium
caseinate, although, in the case of ammonium caseinate, a lot of the ammonia is evaporated
from the solution during the drying process. A solution of sodium caseinate, like those of
potassium and ammonium caseinates, has a straw-like colour and is completely different in
appearance from milk. Solutions of calcium caseinate, on the other hand, are very white and
opaque - even whiter than milk, and they are less viscous than solutions of the other
caseinates. Calcium caseinate solutions are produced by adding a slurry of lime (calcium
hydroxide) in water to a casein curd-water mixture and reacting the combined slurries at a
relatively low temperature (< 45oC) until the neutralisation reaction is completed. Use of
higher temperatures before neutralisation is completed is likely to result in precipitation or
coagulation of the partly reacted calcium caseinate, with probable dumping of the contents of
the reaction vessel.
All caseinate powders have a white appearance.
COMPOSITION OF CASEIN PRODUCTS
The typical composition of well-washed acid casein is shown in Table 1. As noted earlier,
when the same manufacturing operations are used, the caseins produced from lactic,
sulphuric or hydrochloric acid precipitation are almost indistinguishable from one another.
Table 1 also shows that rennet casein differs from acid casein particularly in ash content and
in the pH of a water extract. During the acidification process in the manufacture of acid
casein, the calcium and inorganic phosphate (that are associated with the casein micelle in
milk) are dissolved and leached from the curd leaving only the organic phosphorus and a
small residue of calcium. Rennet casein contains about 3% calcium and approximately 1.4%
phosphorus.

III-Dairy-E-Casein-7

ACID CASEIN CURD

(or DRY ACID CASEIN)
mixing

WATER

DILUTE ALKALIa

wet milling

mixing

dissolving

HEAT (steam or hot water)

COOL + MOISTURE

spray drying

HOT AIR

BAGS (capacity 20 kg)

blending

sampling

bagging

storage

Figure 5 -

Processing steps involved in the manufacture of sodium caseinate from

acid casein curd or dry acid casein (Notea: in this case, sodium alkali
would be used.).

The composition of sodium and calcium caseinates is also shown in Table 1. As they are
spray-dried products, their moisture content is much lower than that of the caseins, and their
protein content is consequently higher. With a pH generally in the range 6.5-7.0, sodium
caseinate will usually contain 1.2-1.4% sodium, whereas the calcium content of calcium
caseinate is generally in the range 1.3-1.6%.

III-Dairy-E-Casein-8

Table 1 Component

Composition of casein and caseinates

Acid
casein

Rennet
casein

Sodium
caseinate

Calcium
caseinate

Moisture (%)

11.4

11.4

3.8

3.8

Protein (%)

85.4

79.9

91.4

91.2

Ash (%)

1.8

7.8

3.6

3.8

Lactose (%)

0.1

0.1

0.1

0.1

Fat (%)

1.3

0.8

1.1

1.1

Sodium (%)

< 0.1

< 0.1

1.2-1.4

< 0.1

Calcium (%)

0.1

2.6-3.0

0.1

1.3-1.6

pH

4.6-5.4

7.3-7.7

6.5-6.9

6.8-7.0

pH of whey
after separation
of curd

4.3-4.6

6.5-6.7

100

90-98

Solubility in
water (%)

PROPERTIES OF CASEIN PRODUCTS

Solubility
Acid and rennet casein are insoluble in water. Virtually all applications of casein products
require them to be dissolved first. Consequently, before use, acid casein must be dissolved
using an alkali to produce a solution with a pH of 6.5 or higher. The caseinates mentioned in
the previous sections are used for food and pharmaceutical applications. For non-food,
technical applications, acid casein may be dissolved in other alkalis such as borax or
ammonia, usually to a somewhat higher pH (7.5-9.5, or higher) than that used for edible
applications.
Water absorption and viscosity
Casein products can absorb substantial amounts of water, so they can modify the texture of
dough or baked products, serve as the matrix former in cheese-type products, produce
specialised plastic materials, or increase the consistency of solutions such as soups. They are
good film-formers and find use in whipping and foaming applications, and in emulsions of
fats or oils in water.

III-Dairy-E-Casein-9

Nutrition
The nutritional quality of a protein is determined primarily by its essential amino acid
content. For adult man, eight amino acids are essential, i.e. they must be supplied in the diet.
These are isoleucine, leucine, lysine, methionine, phenylalanine, threonine, tryptophan and
valine; the infant requires histidine as well. In comparison with an ideal reference protein
composition that was developed by the FAO in 1973, casein contains an adequate supply of
all the essential amino acids with the possible exception of the sulphur-containing amino
acids methionine and cysteine.
FOOD USES OF CASEIN PRODUCTS
The uses of casein products in foods are summarised in Table 2.
Table 2 -

Edible applications of casein products

Bakery
Coffee whiteners and creamers
Cultured milk products, yoghurt etc.
spreads
Ice cream and frozen desserts
Instant breakfasts and beverages
Nutritional food bars
Pharmaceuticals
Sports drinks

Cheese products
Confectionery
High fat powders, shortenings and
Infant foods
Meat products
Pasta
Soups and gravies
Whipped toppings

Casein is generally not consumed as a food on its own. Casein products are used mainly as
ingredients in foods for the purpose of either modifying the physical properties of that food
product or providing nutritional supplementation to it. As a consequence, they usually form a
relatively minor proportion of the food. The function and use level of casein in the different
food product groups listed in Table 2 are shown in Table 3.
TECHNICAL (NON-FOOD) USES OF CASEIN PRODUCTS
Casein has been used commercially in non-food technical applications since the mid-19th
century, initially in adhesives and water-based paints. These applications have multiplied
during the 20th century and a list of current use categories is shown in Table 4.

III-Dairy-E-Casein-10

Table 3 -

Function and use level of casein products in foods

Food category

Casein product

Use levelb

Function

Baked products

Casein, caseinates

1-25%

Nutrition, water binding

Cheese products

Rennet casein, acid

casein, caseinates

2-25%

Fat and water binding,

texture, matrix formation

Coffee whiteners

Sodium caseinate

1-10%

Fat emulsification

Confectionery

Caseinates (whole
and hydrolysed)

1-25%

Texture

Cultured products

Sodium caseinate

2-3%

Fat emulsifier, stabiliser

High fat powders

Sodium caseinate

up to 10%

Fat emulsifier

Ice cream

Sodium caseinate

1-5%

Texture, stabiliser

Infant foods

Whole or
hydrolysed caseina

1-25%

Nutrition

Instant breakfasts
and beverages

Sodium caseinate

2-30%

Nutrition

Meat products

Sodium caseinate

3-20%

Nutrition, fat emulsifier,

water binding, texture

Nutritional food
bars

Casein, caseinates

10-20%

Nutrition, texture

Pasta and snacks

Casein, caseinates

5-20%

Nutrition, texture

Pharmaceuticals

Casein, caseinates,
hydrolysed casein

5-95%

Nutrition

Soups and gravies

Sodium caseinate

5-20%

Nutrition, thickener

Sports drinks

Sodium caseinate

2-10%

Nutrition

Whipped toppings

Sodium caseinate

5-10%

Film former, fat emulsifier,

stabiliser, bodying agent

Notea: Hydrolysed casein (hydrolysates) is derived from whole casein by reacting it in

solution with a proteolytic enzyme. Hydrolysates are generally used in nutritional,
pharmaceutical or medical applications where the whole protein is not readily
digestible.
Noteb: Typical or estimated values.

III-Dairy-E-Casein-11

Table 4 -

Technical uses of casein

Acid casein

Rennet casein

Adhesive for wood, e.g. plywood;

adhesive for foil laminates and paper
Coatings for paper and cardboard
Horticultural spreaders

Plastics in the form of buttons, buckles,

imitation tortoiseshell (combs and
hairclips), imitation ivory (knife handles
and piano keys), fountain pen barrels,
shoehorns, dominoes, novelties

Joint cements in wallboard

Leather tanning
Paints
Photo-resist
Stock foods
Synthetic fibres
Textile sizing

GLOSSARY
acidulation

A period of time (5-10 minutes) when the mixture of

cooked casein curd and whey is gently stirred in a vat
before separation of curd and whey for further
processing.

blending

Mixing of milled and sifted dry casein particles to

achieve uniformity in composition and properties prior
to bagging and storage.

S1-casein, -casein, -casein

Fractions of whole casein that have very slight

differences in amino acid composition.

caseinate

The water-soluble, neutralised (salt) form of acid

casein. The most common are sodium and calcium
caseinates.

chymosin

The more scientifically correct name for rennet.

coagulum/"coag"

A term describing the gel formed in milk after its

acidification to pH ca. 4.6 using lactic starter bacteria.

colloid mill

A powerful mill with very fine tolerances used for wetmilling of aqueous slurries of casein curd.

III-Dairy-E-Casein-12

cooking

The heating of coagulated or clotted or acidified milk,

usually by steam injection or by means of a heat
exchanger.

dewatering

Separation of casein curd and wash water, often by

meachanical means.

glycomacropeptide

The fragment (or peptide) that is split off the casein

during the action of rennet (or chymosin).

para--casein

The casein remaining after the action of rennet or

chymosin.

proteolytic

Causing breakdown of protein bonds.

rennet

A proteolytic enzyme found in the fourth stomach of a

young calf. It is used in the manufacture of cheese and
rennet casein, when it splits off a small fragment
(known as glycomacropeptide) from the casein.

starter

A culture of several defined strains of bacteria that are

added to milk to convert some of the lactose (milk
sugar) to lactic acid during the manufacture of cheese
and lactic acid casein.

tempering

A period of time when casein from the drier is mixed

and held in storage bins to allow time for the
equilibration of moisture among all the particles.

Written by C. R. Southward (Consumer and Applications Science Section, New Zealand

Dairy Research Institute).

III-Dairy-E-Casein-13