C8051F930 Gdi

C8051F930-GDI
Tested Single/Dual Battery, 0.93.6 V, 64 kB Flash,

SmaRTClock, 10-Bit ADC MCU Die in Wafer Form
Supply Voltage 0.9 to 3.6 V
- One-Cell Mode supports 0.9 to 1.8 V operation
- Two-Cell Mode supports 1.8 to 3.6 V operation
- Built-in dc-dc converter with 1.8 to 3.3 V output for
sectors--1024 bytes are reserved in the 64 kB

devices
use in one-cell mode

Built-in LDO regulator allows a high analog supply
voltage and low digital core voltage
2 built-in supply monitors (brownout detectors)
Digital Peripherals
- 24 port I/O; All 5 V tolerant with high sink current
10-Bit Analog to Digital Converter

- 1LSB INL; no missing codes
- Programmable throughput up to 300 ksps
- 23 external inputs
- On-Chip Voltage Reference
- On-Chip PGA allows measuring voltages up to twice
the reference voltage

16-bit Auto-Averaging Accumulator with Burst Mode
provides increased ADC resolution
Data dependent windowed interrupt generator
Built-in temperature sensor
Two Comparators
- Programmable hysteresis and response time
- Configurable as wake-up or reset source
- 23 Capacitive Touch Sense inputs
6-Bit Programmable Current Reference
- Up to 500 A. Can be used as a bias or for generating a custom reference voltage
ports UART operation; 20 MHz low power oscillator

requires very little bias current
External oscillator: Crystal, RC, C, or CMOS Clock
SmaRT Clock oscillator: 32 kHz Crystal or internal
self-oscillate mode
Can switch between clock sources on-the-fly; useful
in implementing various power saving modes
Temperature range: 40 to +85 oC

Full Technical Data Sheet
- C8051F93x-C8051F92x
On-Chip Debug
- On-chip debug circuitry facilitates full-speed, nonintrusive in-system debug (no emulator required)
- Provides breakpoints, single stepping

- Inspect/modify memory and registers
- Complete development kit
High-Speed 8051 C Core
- Pipelined instruction architecture; executes 70% of
-
Clock Sources
- Internal oscillators: 24.5 MHz, 2% accuracy sup-
instructions in 1 to 2 system clocks

25 MIPS throughput with 25 MHz clock
Expanded interrupt handler
ANALOG
PERIPHERALS
A
M
U
X
10-bit
300 ksps
ADC
TEMP
SENSOR
VREF
VREG
IREF
VOLTAGE
COMPARATORS
DIGITAL I/O
UART
SMBus
2 x SPI
PCA
Timer 0
Timer 1
Timer 2
Timer 3
CRC
CROSSBAR
and programmable drive strength

Hardware SMBusTM (I2C Compatible), 2 x SPITM,
and UART serial ports available concurrently
Four general purpose 16-bit counter/timer array with
six capture/compare modules and watchdog timer
Hardware SmaRTClock operates down to 0.9V and
requires less than 0.5 A supply current
EMIF
Memory
- 4352 bytes internal data RAM (256+4096)
- 64 kB Flash; In-system programmable in 1024-byte
Port 0
Port 1
Port 2
24.5 MHz PRECISION

INTERNAL OSCILLATOR
20 MHz LOW POWER

INTERNAL OSCILLATOR
External Oscillator
HARDWARE SmaRTClock
HIGH-SPEED CONTROLLER CORE

64 kB
ISP FLASH
FLEXIBLE
INTERRUPTS
Rev. 1.3 11/13
8051 CPU
(25 MIPS)
DEBUG
CIRCUITRY
4352 B
SRAM
POR
WDT
Copyright 2013 by Silicon Laboratories
C8051F930-GDI
UART
Enhanced SPI
Timers (16-bit)
Programmable Counter Array
Digital Port I/Os
C8051F930-G-G1DI 25
64 4352
1
1
2
4
24
28.54 mil /
725 m
(no backgrind)
C8051F930-G-GDI
64 4352
1
1
2
4
24
12 mil
(backgrind)
25
*Note: 1024 bytes reserved for factory use.
Rev. 1.3
Wafer Thickness
Lead-free (RoHS Compliant)
Analog Comparators
Temperature Sensor
Internal Voltage Reference
Programmable Current Reference
10-bit 300ksps ADC
SmaRTClock Real Time Clock
RAM (Bytes)
Flash Memory (kB)
MIPS (Peak)
SMBus/I2C
Ordering Part Number
C8051F930-GDI
1. Ordering Information
Table 1.1. Product Selection Guide
C8051F930-GDI
2. Pin Definitions
Table 2.1. Pin Definitions for the C8051F930-GDI
Name
Physical
Pad
Number
Type
Description
VBAT
P In
Battery Supply Voltage. Must be 0.9 to 1.8 V in single-cell battery

mode and 1.8 to 3.6 V in dual-cell battery mode.
VDD /
P In
Power Supply Voltage. Must be 1.8 to 3.6 V. This supply voltage is

not required in low power sleep mode. This voltage must always be >
VBAT.
P Out
Positive output of the dc-dc converter. In single-cell battery mode, a

1uF ceramic capacitor is required between DC+ and DC. This pin
can supply power to external devices when operating in single-cell
battery mode.
P In
DC-DC converter return current path. In single-cell battery mode, this

pin is typically not connected to ground.
DC+
DC /
GND
In dual-cell battery mode, this pin must be connected directly to

ground.
Required Ground.
GND
DCEN
P In
G
RST/
C2CK
P2.7/
C2D
DC-DC Enable Pin. In single-cell battery mode, this pin must be connected to VBAT through a 0.68 H inductor.
In dual-cell battery mode, this pin must be connected directly to
ground.
D I/O
Device Reset. Open-drain output of internal POR or VDD monitor. An

external source can initiate a system reset by driving this pin low for
at least 15 s. A 1 k to 5 k pullup to VDD is recommended. See
Reset Sources section of the C8051F93x-C8051F92x data sheet for
a complete description.
D I/O
Clock signal for the C2 Debug Interface.
D I/O
Port 2.7. This pin can only be used as GPIO. The Crossbar cannot
route signals to this pin and it cannot be configured as an analog
input. See Port I/O section the C8051F93x-C8051F92x data sheet
for a complete description.
D I/O
Bi-directional data signal for the C2 Debug Interface.

SmaRTClock Oscillator Crystal Input.
XTAL3
11
A In
XTAL4
10
A Out
SmaRTClock Oscillator Crystal Output.
Rev. 1.3
C8051F930-GDI
Table 2.1. Pin Definitions for the C8051F930-GDI (Continued)
Name
Physical
Pad
Number
P0.0
39
VREF
P0.1
Type
D I/O or Port 0.0. See Port I/O section of the C8051F93x-C8051F92x data
A In
sheet for a complete description.
A In
A Out
38
AGND
Description
External VREF Input.

Internal VREF Output. External VREF decoupling capacitors are recommended. See ADC0 section of the C8051F93x-C8051F92x data
sheet for details.
A In
G
Optional Analog Ground. See ADC0 section of the C8051F93xC8051F92x data sheet for details.
P0.2
33
XTAL1
A In
A In
External Clock Input. This pin is the external oscillator return for a
crystal or resonator. See Oscillator section of the C8051F93xC8051F92x data sheet for a complete description.
P0.3
32
XTAL2
A In
A Out
D In
A In
P0.4
TX
31
External Clock Output. This pin is the excitation driver for an external
crystal or resonator.
External Clock Input. This pin is the external clock input in external
CMOS clock mode.
External Clock Input. This pin is the external clock input in capacitor
or RC oscillator configurations.
See Oscillator section of the C8051F93x-C8051F92x data sheet for
complete details.
A In
D Out
UART TX Pin. See Port I/O section of the C8051F93x-C8051F92x
data sheet for a complete description.
Rev. 1.3
C8051F930-GDI
Name
Physical
Pad
Number
P0.5
30
RX
Type
Description
A In
D In
UART RX Pin. See Port I/O section of the C8051F93x-C8051F92x
data sheet for a complete description.
P0.6
29
CNVSTR
A In
D In
External Convert Start Input for ADC0. See ADC0 section of the
C8051F93x-C8051F92x data sheet for a complete description.
P0.7
28
A In
A Out
IREF0 Output. See IREF section of the C8051F93x-C8051F92x data
sheet for complete description.
27
A In
sheet for a complete description. May also be used as SCK for SPI1.
IREF0
P1.0
AD0
P1.1
D I/O
26
A In
May also be used as MISO for SPI1.
D I/O
Address/Data 1.
25
A In
May also be used as MOSI for SPI1.
D I/O
Address/Data 2.
24
A In
May also be used as NSS for SPI1.
D I/O
Address/Data 3.
21
A In
AD1
P1.2
AD2
P1.3
AD3
P1.4
AD4
Address/Data 0.
D I/O
Address/Data 4.
Rev. 1.3
C8051F930-GDI
Name
Physical
Pad
Number
P1.5
20
AD5
Type
Description
A In
D I/O
Address/Data 5.
P1.6
19
AD6
A In
D I/O
Address/Data 6.
P1.7
18
AD7
A In
D I/O
Address/Data 7.
P2.0
17
AD8
A In
D I/O
Address/Data 8.
P2.1
16
AD9
A In
D I/O
Address/Data 9.
P2.2
15
AD10
A In
D I/O
Address/Data 10.
P2.3
14
A In
D I/O
AD11
Address/Data 11.
P2.4
ALE
13
A In
DO
Address Latch Enable.
Rev. 1.3
C8051F930-GDI
Name
Physical
Pad
Number
P2.5
12
RD
P2.6
WR
Type
A In
DO
Description
Read Strobe.
A In
DO
Write Strobe.
Rev. 1.3
C8051F930-GDI
3. Bonding Instructions
Table 3.1. Bond Pad Coordinates (Relative to Center of Die)
Physical Pad
Number
Example Package
Pin Number
(QFN-32)
Package Pin Name
Physical Pad X
(m)
Physical Pad Y
(m)
Reserved*
1013
614
DC/GND
1013
494
GND
1013
247
VDD/DC+
1013
92
DCEN
1013
91
VBAT
1013
315
RST/C2CK
1013
626
P2.7/C2D
1013
810
P2.6/WR
810
1013
10
XTAL4
525
1013
11
10
XTAL3
303
1013
12
11
P2.5/RD
54
1013
13
12
P2.4/ALE
130
1013
14
13
P2.3/AD11
286
1013
15
14
P2.2/AD10
470
1013
16
15
P2.1/AD9
626
1013
17
16
P2.0/AD8
810
1013
18
17
P1.7/AD7
1013
810
19
18
P1.6/AD6
1013
626
20
19
P1.5/AD5
1013
470
21
20
P1.4/AD4
1013
286
22
Reserved*
1013
174
23
Reserved*
1014
94
24
21
P1.3/AD3
1013
137
*Note: Pins marked Reserved should not be connected.
Rev. 1.3
C8051F930-GDI
Table 3.1. Bond Pad Coordinates (Relative to Center of Die) (Continued)
Physical Pad
Number
Example Package
Pin Number
(QFN-32)
Package Pin Name
Physical Pad X
(m)
Physical Pad Y
(m)
25
22
P1.2/AD2
1013
279
26
23
P1.1/AD1
1013
477
27
24
P1.0/AD0
1013
619
28
25
P0.7/IREF0
1013
817
29
26
P0.6/CNVSTR
817
1013
30
27
P0.5/RX
619
1013
31
28
P0.4/TX
477
1013
32
29
P0.3/XTAL2
279
1013
33
30
P0.2/XTAL1
137
1013
34
Reserved*
1013
35
Reserved*
97
1013
36
Reserved*
413
1013
37
Reserved*
503
1013
38
31
P0.1/AGND
626
1013
39
32
P0.0/VREF
810
1013
*Note: Pins marked Reserved should not be connected.
Rev. 1.3
C8051F930-GDI
C8051F930G
Figure 3.1. Example Die Bonding (QFN-32)
10
Rev. 1.3
C8051F930-GDI
Table 3.2. Wafer and Die Information
C8051F930G
Wafer ID
8 in
Wafer Dimensions
2.28 mm x 2.28 mm
Die Dimensions
12 mil 1 mil
Wafer Thickness (with backgrind)
28.54 mil 1 mil, 725 m
Wafer Thickness (no backgrind)

Wafer Identification
Notch
Scribe Line Width
80 m
Contact Sales for info
Die Per Wafer*

Passivation
Standard
Wafer Packaging Detail
Wafer Jar
Bond Pad Dimensions
60 m x 60 m
Maximum Processing Temperature
250 C
Electronic Die Map Format
.txt
Bond Pad Pitch Minimum
142 m
*Note: This is the Expected Known Good Die yielded per wafer and represents
the batch order quantity (one wafer).
Rev. 1.3
11
C8051F930-GDI
4. Wafer Storage Guidelines
It is necessary to conform to appropriate wafer storage practices to avoid product degradation or contamination.
Wafers
may be stored for up to 18 months in the original packaging supplied by Silicon Labs.
must be stored at a temperature of 1824 C.
Wafers must be stored in a humidity-controlled environment with a relative humidity of <30%.
Wafers should be stored in a clean, dry, inert atmosphere (e.g. nitrogen or clean, dry air).
Wafers
12
Rev. 1.3
C8051F930-GDI
5. Failure Analysis (FA) Guidelines
Certain conditions must be met for Silicon Laboratories to perform Failure Analysis on devices sold in
wafer form.
In
order to conduct failure analysis on a device in a customer-provided package, Silicon

Laboratories must be provided with die assembled in an industry standard package that is pin
compatible with existing packages Silicon Laboratories offers for the device. Initial response time
for FA requests that meet this requirements will follow the standard FA guidelines for packaged
parts.
If retest of the entire wafer is requested, Silicon Laboratories must be provided with the whole
wafer. Silicon Laboratories cannot retest any wafers that have been sawed, diced, backgrind or
are on tape. Initial response time for FA requests that meet this requirements will be three weeks.
Rev. 1.3
13
C8051F930-GDI
DOCUMENT CHANGE LIST
Revision 1.1 to Revision 1.2
Changed Wafer Packaging Detail to Wafer Jar

in Table 3.2 on page 11.
Revision 1.2 to Revision 1.3
Replaced C8051F930-GDI with C8051F930-G-GDI (except in title).

Updated Table 1.1 on page 2 with C8051F930-G-G1DI row.
Updated label on Figure 3.1 on page 10 to C8051F930G.
Updated Table 3.2 on page 11.
Added Failure Analysis (FA) Guidelines on page 13.
14
Rev. 1.3
Simplicity Studio
One-click access to MCU and
wireless tools, documentation,
software, source code libraries &
more. Available for Windows,
Mac and Linux!
IoT Portfolio
www.silabs.com/IoT
SW/HW
Quality
Support and Community
www.silabs.com/simplicity
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the worlds most energy friendly microcontrollers", Ember, EZLink, EZMac, EZRadio, EZRadioPRO, DSPLL, ISOmodem , Precision32, ProSLIC, SiPHY,
USBXpress and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.

400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com

C8051F930 Gdi

Uploaded by

Copyright:

Available Formats

C8051F930 Gdi

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C8051F930 Gdi

Uploaded by

Copyright:

Available Formats

C8051F930-GDI

Tested Single/Dual Battery, 0.93.6 V, 64 kB Flash,

sectors--1024 bytes are reserved in the 64 kB

use in one-cell mode

10-Bit Analog to Digital Converter

the reference voltage

ports UART operation; 20 MHz low power oscillator

Temperature range: 40 to +85 oC

- Provides breakpoints, single stepping

instructions in 1 to 2 system clocks

and programmable drive strength

24.5 MHz PRECISION

20 MHz LOW POWER

HIGH-SPEED CONTROLLER CORE

Rev. 1.3 11/13

Copyright 2013 by Silicon Laboratories

*Note: 1024 bytes reserved for factory use.

Lead-free (RoHS Compliant)

Internal Voltage Reference

Programmable Current Reference

10-bit 300ksps ADC

SmaRTClock Real Time Clock

Flash Memory (kB)

Ordering Part Number

Battery Supply Voltage. Must be 0.9 to 1.8 V in single-cell battery

Power Supply Voltage. Must be 1.8 to 3.6 V. This supply voltage is

Positive output of the dc-dc converter. In single-cell battery mode, a

DC-DC converter return current path. In single-cell battery mode, this

In dual-cell battery mode, this pin must be connected directly to

Device Reset. Open-drain output of internal POR or VDD monitor. An

Clock signal for the C2 Debug Interface.

Bi-directional data signal for the C2 Debug Interface.

SmaRTClock Oscillator Crystal Output.

External VREF Input.

Address Latch Enable.

Package Pin Name

*Note: Pins marked Reserved should not be connected.

Package Pin Name

*Note: Pins marked Reserved should not be connected.

Figure 3.1. Example Die Bonding (QFN-32)

Wafer Thickness (with backgrind)

28.54 mil 1 mil, 725 m

Wafer Thickness (no backgrind)

Scribe Line Width

Die Per Wafer*

Wafer Packaging Detail

Bond Pad Dimensions

Maximum Processing Temperature

Electronic Die Map Format

Bond Pad Pitch Minimum

order to conduct failure analysis on a device in a customer-provided package, Silicon

Changed Wafer Packaging Detail to Wafer Jar

Revision 1.2 to Revision 1.3

Replaced C8051F930-GDI with C8051F930-G-GDI (except in title).

Support and Community

Silicon Laboratories Inc.

You might also like