MK7A25P

8Bit Microcontroller with 10bit ADC

General Description
The MK7A25P is an 8 bit RISC high performance microcontroller with 10bit A/D converter. It is equipped
with 2K word OTP(One Time Programmable) ROM, 128 Bytes RAM, Timer/Counter, Capture, Interrupt,
LVR(Low Voltage Reset), I/O ports and PWM output in a single chip.

1. Feature
ROM size: 2K x 16 bits
RAM: 37 x 8 bits(Special Purpose Register)
+ 128 x 8 (General Purpose Register)
STACK: 8 Levels
One instruction build by two systems clock.
Reset mode:
(a) Power-On reset
(b) Low voltage reset
(c) RESETB/PC1 (if be set as reset pin) input
a negative pulse.
(d) Watchdog timer count overflow reset
Dual Clock Mode
- External RC or Crystal oscillator
- Internal 4MHz RC oscillator
Timer/counter: 3 units.
- TM1: 16-bit, capture & Timer.
- TM2: 8-bit, PWM (period) & Timer.
- TM3: 8-bit, PWM (duty) & Timer.
- TO : TM2(PWM) clock out
Watchdog Timer: On chip WDT is based on
an internal RC oscillator (for WDT used
only). Have 8 period can be selected. User
can extend the WDT overflow period by
using prescaler.
Interrupt events:
(a) External interrupt (PA7~PA0).
(b) Internal timer/event counter interrupt
(TM1~TM3).
(c) ADC end of conversion interrupt
I/O port: 16 pins
PWM: one channel
ADC: max 10(6+4)-bit and 4 channels, at least
10-bit resolution. It can use at converter mode
or compare mode
Wake-up mode:
1. Port A (PA7~PA0) pin change wakeup
2. i_WDT wakeup
Different Package Type:
MK7A25PD20C: 20 pin DIP
MK7A25PS20C: 20 pin SOP
MK7A25PD18C: 18 pin DIP
MK7A25PS18C: 18 pin SOP
MK7A25PD14C: 14 pin DIP
MK7A25PS14C: 14 pin SOP









MK7A25P

2010/09/13 Rev.06

2

2. Block Diagram



CPU
CORE
ROM
2K x 16 bit
RAM
128
Bytes
RESET
OSC
Clock &
Timer
I/ O Port
PWM output
Watchdog
Timer
RESET
OSC1
OSC2
PA 0 ~7
PB 0 ~3
VDD
GND
A/D Converter
PWM
EXT_CLK
STACK
& PC
TO

MK7A25P

2010/09/13 Rev.06

3

3. Pin Definition & Pad Assignment


PA 3 / TO
PA 2
PA 1
PA 4 / EXT_
CLK
PA 5
PA 6
PA 7 PA 0
OSC 2 / PC 3 PB 3 / AN 3
PWM_OPT/PB 2 / AN 2
PB 1 / AN 1
PB 0 / AN 0
VSS
OSC1 / PC 2
RESETB / PC 1
VDD
PWM / PC 0
1
2
3
4
6
7
8
9
10
20
19
18
17
15
14
13
12
11
PC 5 5 PC 4 16
PDIP 20 or SOP20
PA 3 / TO
PA 2
PA 1
PA 4 / EXT _
CLK
PA 5
PA 6
PA 7 PA 0
OSC2 / PC 3 PB 3 / AN 3
PWM_OPT/PB 2 / AN 2
PB 1 / AN 1
PB 0 / AN 0
VSS
OSC1 / PC 2
RESETB / PC 1
VDD
PWM / PC 0
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
PDIP 18 or SOP18
PA 4 / EXT _
CLK
PA 5
OSC 2 / PC 3
OSC1 / PC 2
VDD
PWM_OPT/PB 2 / AN 2
PB 1 / AN 1
PB 0 / AN 0
VSS
RESETB / PC 1
PWM / PC 0
1
2
3
4
5
6
7
14
13
12
11
10
9
8
PA 3 / TO
PA 2
PB 3 / AN 3
PDIP 14 or SOP14


MK7A25P

2010/09/13 Rev.06

4

4. PIN Description

Pin name I/O Pin
type
Description
PA0~2
PA5~7
I/O D
1. I/O port (Pull-up option with Input mode)
2. Wake-up on pin change (option)
3. External interrupt input (option)
PA3/TO I/O D
1. I/O port (Pull-up option with Input mode)
2. Wake -up on pin change (option)
3. External interrupt input (option)
4. TO clock out
PA4/EXT_CLK I/O D
1. I/O port (Pull-up option with Input mode)
2. EXT_CLK clock input (or capture input)
3. Wake -up on pin change (option)
4. External interrupt input (option)
PB3/AN3 I/O A
PB1/AN1 I/O A
PB0/AN0 I/O A
1. I/O port (Pull-up option with Input mode)
2. Analog input
PWM_OPT/PB2/AN
2
I/O A
1. I/O port (Pull-up option with Input mode)
2. Analog input
3. PWM option output, when PWM_OPT($1DH)set to 1.
PWM/PC0 I/O D
4. I/O port (Pull-up option with Input mode)
5. PWM output , when PWM_OPT($1DH)reset to 0(init)
RESETB/PC1 I B
1. Reset pin
2. Input port
OSC1/PC2 I, I/O C
1. Oscillator input
2. I/O port (Pull-up option with Input mode)
OSC2/PC3 O, I/O C
1. Oscillator output
2. I/O port (Pull-up option with Input mode)
PC4~PC5 I/O D
1. I/O port (Pull-up option with Input mode)
2. The initial state pull_up(UC5,UC4) is enable.
VDD P Power input
VSS P Ground input




MK7A25P

2010/09/13 Rev.06

5
4.1 PIN Circuit


VDD
VDD
I/O
Data
Pull-high enable
Output disable
(input mode)
Long channel
Digital input
Pin circuit Type A
Analog enable
Analog enable
Analog enable
Analog input








in
Pin circuit Type B




MK7A25P

2010/09/13 Rev.06

6

VDD
VDD
I/O
Data
Pull-high enable
Output disable
(input mode)
Long channel
Digital input
Pin circuit Type C
crystal enable
crystal enable
crystal enable



VDD
VDD
I/O
Data
Pull-high
enable
Output disable
(input mode)
Long channel
Digital
input
Pin circuit Type D











MK7A25P

2010/09/13 Rev.06

7
5. Memory Map

The MK7A25P have two kinds of memory which are ROM (program memory) and RAM (data memory). The
ROM is used to store the program, table and interrupt vectors. It is continuous 2048 X 16bits and dont need to
switch bank. The RAM is 165(37+128) X 8 bits that include special function register and general-purpose RAM.

5.1 Program Memory (ROM)
Instruction and table are stored at this area. There is only one interrupt vector existed which means all the
interrupt occurred would jump to the same vector. Programmer should use interrupt flag to judge what kind of
interrupt is occurred. The program counter (PC) is 11 bit which can directly address all the 2048 x 16 location.
Look-up table can be put at anywhere of ROM.
The RESET vector is located at 000H and Interrupt vector is at 004H. The map is as below:

RESET VECTOR
INTERRUPT VECTOR
000H
004H
7FFH
PC (11bit)
STACK Level 1
STACK Level 2
STACK Level 3
STACK Level 4
STACK Level 5
STACK Level 6
STACK Level 7
STACK Level 8



5.2 Data Memory (RAM)
The total RAM volume are 165x8bits which includes two kinds of register group. One is 1288 bits general
purpose RAM, the other is special purpose register that are 378 bits. Every byte of special purpose register
stored controls data or operations data.
The data memory map is as below:

MK7A25P

2010/09/13 Rev.06

8
Special Purpose
Register
00H
3FH
40H
BFH
General Purpose
RAM

5.2.1 Special Purpose Register
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
CONFIG_L RST_DEF -- -- WDTE CPRT INRC FOSC1 FOSC0
CONFIG_H ADJ6 ADJ5 ADJ4 ADJ3 ADJ2 ADJ1 ADJ0 RTCEN
INDF $00 A7 A6 A5 A4 A3 A2 A1 A0
PCL $01 A7 A6 A5 A4 A3 A2 A1 A0
PCH $02 -- -- -- -- -- A10 A9 A8
STATUS $03 -- -- --
TO PD
Z DC C
FSR $04 D7 D6 D5 D4 D3 D2 D1 D0
I/O PAD & Control
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PA_DIR $05 IOA7 IOA6 IOA5 IOA4 IOA3 CA2 IOA1 IOA0
PA_DAT $06 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0
PB_DIR $07 -- -- -- -- IOB3 IOB2 IOB1 IOB0
PB_DAT $08 -- -- -- -- DB3 DB2 DB1 DB0
PC_DIR $09 -- -- IOC5 IOC4 IOC3 IOC2 -- IOC0
PC_DAT $0A -- -- DC5 DC4 DC3 DC2 DC1 DC0
Timer 1: 16-bit (Timer & capture)
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM1_CTL1 $13 TM1_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
TM1_CTL2 $1F E_CLR -- -- -- -- -- -- --
CLR_CNT $21 CLR_CNT

MK7A25P

2010/09/13 Rev.06

9
TM1L_LA $14 D7 D6 D5 D4 D3 D2 D1 D0
TM1H_LA $15 D7 D6 D5 D4 D3 D2 D1 D0
TM1L_CNT $16 D7 D6 D5 D4 D3 D2 D1 D0
TM1H_CNT $17 D7 D6 D5 D4 D3 D2 D1 D0
Timer 2: 8-bit, PWM (period) & Timer
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM2_CTL1 $18 TM2_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
TM2_CTL2 $19 MOD PWM_OS TO_E -- POS3 POS2 POS1 POS0
TM2_LA $1A D7 D6 D5 D4 D3 D2 D1 D0
TM2_CNT $1C D7 D6 D5 D4 D3 D2 D1 D0
Timer 3: 8-bit, PWM (duty) & Timer
Name Addr Bit 7 Bit 6 Bit 5
Bit
4
Bit 3 Bit 2 Bit 1 Bit 0
PWM_OPT $1D PWM_OPT -- -- -- -- -- -- --
TM3_CTL $1E TM3_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
TM3_LA $20 D7 D6 D5 D4 D3 D2 D1 D0
TM3_CNT $22 D7 D6 D5 D4 D3 D2 D1 D0
IRQ
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
IRQM $25 INTM ADCM -- PAM TM3M TM2M/PWM TM1M/CPT --
IRQF $26 -- ADCF -- PAF TM3F TM2F/PWM TM1F/CPT --
ADC control
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_CTL1 $29 EN -- MODE -- -- -- CHSEL1 CHSEL0
AD_CTL2 $2A RSUT -- -- -- -- -- CKSEL1 CKSEL0
AD_CTL3 $2B -- -- -- -- -- PBSEL2 PBSEL1 PBSEL0
AD_DAT_L $2C D1 D0 -- -- -- -- -- --
AD_DAT_H $2D D9 D8 D7 D6 D5 D4 D3 D2
Other
Name Addr Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PA_PLU $31 UA7 UA6 UA5 UA4 UA3 UA2 UA1 UA0
PB_PLU $33 -- -- -- -- UB3 UB2 UB1 UB0
PC_PLU $35 -- -- UC5 UC4 UC3 UC2 -- UC0
WAKEUP $3A EN7 EN6 EN5 EN4 EN3 EN2 EN1 EN0
WDT_CTL $3D WDTEN i_WDT i_STAB -- -- PRE2 PRE1 PRE0

MK7A25P

2010/09/13 Rev.06

10
TAB_BNK $3E -- -- -- -- -- BNK2 BNK1 BNK0
SYS_CTL $3F CLKS -- -- -- -- -- STP1 STP0
<Note> : mean no use.

5.2.2 Configure Register
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
CONFIG_L RST_DEF -- -- WDTE CPRT INRC FOSC1 FOSC0
- Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
CONFIG_H ADJ6 ADJ5 ADJ4 ADJ3 ADJ2 ADJ1 ADJ0 EXT_CLK
Bit15~9 (ADJ6~0): Used to calibrated internal RC oscillator.
Bit8 (EXT_CLK): EXT_CLK input
0: EXT_CLK (PA4) pin is normal I/O pin
1: EXT_CLK (PA4) pin is timer source input & PA4 input
Bit7 (RST_DEF): RESETB pin define
0: RESETB is normal input pin
1: RESETB is system reset pin
Bit4 (WDTE): Watchdog timer enable/disable
0: WDT disable
1: WDT enable
Bit3 (CPRT): ROM Code Protection bit
0: ON
1: OFF

MK7A25P

2010/09/13 Rev.06

11

Bit2~0 (INRC, FOSC1~0): OSC type and system clock select
Bit2 Bit1 Bit0
INRC FOSC1 FOSC0
OSC Type Resonance Frequency
0 0 0 LS (low speed) System clock=32~200KHz
0 0 1 NS (Normal speed) System clock=200K~10MHz
0 1 0 HS (high speed) System clock=10~20MHz
0 1 1 External RC System clock=32K ~ 10MHz
1 0 0 LS &Internal RC
1. Dual clock mode LS & 4MHz
2. Initial system clock=4MHz
1 0 1 NS &Internal RC
1. Dual clock mode NS & 4MHz
2. Initial system clock=4MHz
1 1 0 HS &

Internal RC
1. Dual clock mode HS & 4MHz
2. Initial system clock=4MHz
1 1 1 Internal RC
1. System clock=4MHz
2. OSC1 & OSC2 work as I/O ports

6. Function Descriptions
This device provide many functions that are Timer, WDT, PWM, ADC, Capture, Interrupt, Table location, Reset,
Program Counter and STATUS register. We would like to describe in detail.
6.1 I/O Port
There are 3 I/O ports to input or output data, each port has different function. The port A can be external
interrupt, EXT_CLK clock input or capture input by register option. The port B can be analog input of ADC
function. The port C can be external RC oscillator input, system reset input (reset function) or output of PWM
function.
6.1.1 Port A
There are 3 registers to set the 8 I/O ports which are PA_DIR, PA_DAT, PA_PLU. Each pin of Port A can be
external interrupt input or normal I/O. To know how to set these pins as external interrupt, please refer to
Chapter 6.7. Pin PA4 has multiple functions. User should define it at Configure Register bit 8 at first.
A. PA_DIR($05H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PA_DIR IOA7 IOA6 IOA5 IOA4 IOA3 IOA2 IOA1 IOA0
Bit7~0 (IOA7~0): To define each pin is input port or output port
0: Output.
1: Input.


MK7A25P

2010/09/13 Rev.06

12

B. PA
_
DAT($06H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PA_DAT DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0
Bit7~0 (DA7~0): Data buffer
C. PA_PLU($31H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PA_PLU UA7 UA6 UA5 UA4 UA3 UA2 UA1 UA0
Bit7~0 (UA7~0): Pull up enables/disable
0: Pull-up disable.
1: Pull-up enable.
6.1.2 Port B
There are 3 registers to set the 4 I/O ports which are PB_DIR, PB_DAT, PB_PLU. Each pin of Port B can be set
as ADC analog single input or normal I/O. PB2/ PWM_OPT can be set as PWM output(the PC0 is normal
I/O).To know how to use ADC function, please refer to Chapter 6.8. User can set Pull up while Port B is set as
input mode.
A. PB_DIR($07H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PB_DIR -- -- -- -- IOB3 IOB2 IOB1 IOB0
Bit3~0 (IOB3~0): To define each pin is input port or output port
0: Output.
1: Input.
B. PB
_
DAT($08H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PB_DAT -- -- -- -- DB3 DB2 DB1 DB0
Bit3~0 (DB3~0): Data buffer
C. PB_PLU($33H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PB_PLU -- -- -- -- UB3 UB2 UB1 UB0
Bit3~0 (UB3~0): Pull up enable/disable.
0: Pull-up disable.
1: Pull-up enable.
6.1.3 Port C
There are 3 registers to set the 6 I/O ports which are PC_DIR, PC_DAT, PC_PLU. PC0 (PWM) can be set as
PWM output(the PB2 is normal I/O). To know how to use PWM, please refer to Chapter 6.3. User can set Pull
up while PC3, PC2, PC0 are set as input mode. PC1 (RESETB) can be set as system-reset(Low level voltage
reset) single input pin by CONFIG register. Normally, PC2 (OSC1) and PC3 (OSC2) is external oscillator pin,

MK7A25P

2010/09/13 Rev.06

13
only when internal RC mode is selected, PC2 and PC3 can be normal I/O pin.
A. PC
_
DIR($09H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PC_DIR -- -- IOC5 IOC4 IOC3 IOC2 -- IOC0
Bit5, 4, 3, 2, 0 (IOC5, 4, 3, 2, 0): To define each pin is input port or output port
0: Output.
1: Input.
<Note> IOC1 is input only.
B. PC_DAT($0AH):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PC_DAT -- -- DC5 DC4 DC3 DC2 DC1 DC0
Bit5, 4, 3, 2, 0 (DC5, 4, 3, 2, 0): Data buffer
<Note> 1. DC1 is input data only
C. PC_PLU($35H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PC_PLU -- -- UC5 UC4 UC3 UC2 -- UC0
Bit5, 4, 3, 2, 0 (UC5, 4, 3, 2, 0): Pull up enable/disable.
0: Pull-up disable.
1: Pull-up enable.
Bit5, 4 (UC5, 4): Pull up is enable in the initial state.
6.2 Timer/Event Counter (TM1, TM2, TM3)
The MK7A25P provide 3 countdown timers/counters and 1 watchdog timer. Clock source of counters can be
system clock or external clock by setting each timer control register. TM1 is a 16 bits counter, TM2 and TM3
are 8 bit counter. All these timers have auto reload function, TM1 has capture function and TM2/TM3 can be
cascaded to do PWM function. The detailed registers setting and block diagram are as below.


Prescaler MUX Counter Register
Latch Buffer
Clock Source Select
EXT_CLK
Crystal mode
OSC1 & 2
RC mode
OSC1 & 2
System
clock
Timer reload Capture counter latch
IRQ
Instruction read out



MK7A25P

2010/09/13 Rev.06

14
6.2.1 TM1
TM1 is a 16 bit timer/counter. There are 5 register to set its attributes. To know how to use TM1 Capture
function, please refer to Chapter 6.4.

A.TM1_CTL1 ($13H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM1_CTL1 TM1_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
Bit7 (TM1_EN): Timer1(TM1) enable/disable.
0: TM1 disable.
1: TM1 enable.
Bit6 (WR_CNT): Latch buffer data write to counter register enable/disable.
0: Latch buffer data write to counter register disable.
1: Latch buffer data write to counter register enable
<Note> This bit is set only in the initial state of new timer/counter data to let latch buffer data write to
counter register. When timer is overflow, the latch buffer data would auto reload into counter
register. User doesnt need set again. It has no relation with this bit status.
Bit5~4 (SUR1~0): TM1 clock source selection bits
Bit5 Bit4
SUR1 SUR0
TM1 clock source
0 0 EXT_CLK (PA4)
0 1 Crystal mode OSC1
1 0 RC mode (Ext. & Internal RC) OSC1
1 1 Clock source is system clock and capture input is PA4
<Note> SUR1~0 define TM1 clock source. If TM1 is used in capture function, then SUR1~0 must set to
(1,1) which can record the count from PA4 pin and the clock source is system clock. When capture
is performed, the counter data of TM1 will be latched at TM1L_LA and TM1H_LA
Bit3 (EDGE): TM1 clock source edge control bit
When TM1 use in Timer mode:
0: increment when LH on clock
1: increment when HL on clock
When TM1 use in Capture mode:
0: To save TM1 counter register to latch buffer when EXT_CLK (PA4) LH
1: To save TM1 counter register to latch buffer when EXT_CLK (PA4) HL




MK7A25P

2010/09/13 Rev.06

15

Bit2~0 (PRE2~0): Set TM1 prescaler rate (Timer & capture)
Bit2 Bit1 Bit0
PRE2 PRE1 PRE0
TMR1 Prescaler rate
0 0 0 1:1
0 0 1 1:2
0 1 0 1:4
0 1 1 1:8
1 0 0 1:16
1 0 1 1:32
1 1 0 1:64
1 1 1 1:128

B. TM1_CTL2 ($1FH):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM1_CTL2 ENC -- -- -- -- -- -- --
Bit7 (TM1_CTL1): Capture counter auto clear.
0: Auto clear counter.(hardware)
1: Clear counter by software.(to set CLR_CNT)
C. CLR_CNT ($21H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
CLR_CNT CLR_CNT -- -- -- -- -- -- --
Write this register to clear capture counter. This is edge trigger, so write 0 or 1 are the same.
<Note> If TM1_CTL2 Bit 7 is set to 1 and CLR_CNT doesnt write data, then the counter will be kept instead of
clear to 0.
D. TM1L_LA/TM1H_LA and TM1L_CNT/TM1H_CNT Register ($14H, 15H, 16H, 17H)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM1L_LA D7 D6 D5 D4 D3 D2 D1 D0
TM1H_LA D7 D6 D5 D4 D3 D2 D1 D0
TM1L_CNT D7 D6 D5 D4 D3 D2 D1 D0
TM1H_CNT D7 D6 D5 D4 D3 D2 D1 D0
<Note> TM1L_CNT & TM1H_CNT two register are read only
6.2.2 TM2 (or PWM period)
TM2

is an 8-bit timer/counter. There are 4 registers to set its attribute. The TM2

can be used as PWM period
with TM3 to do PWM waveform.



MK7A25P

2010/09/13 Rev.06

16
A.TM2_CTL1 ($18H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM2_CTL1 TM2_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
Bit7 (TM2_EN): Timer2(TM2)

enable/disable.
0: TM2 disable.
1: TM2 enable.
Bit6 (WR_CNT): Latch buffer data write to counter register enable/disable.
0: Latch buffer data write to counter register disable.
1: Latch buffer data write to counter register enable
<Note> This bit is set only in the initial state of new timer/counter data to let latch buffer data write to
counter register. When timer is overflow, the latch buffer data would auto reload into counter
register. User doesnt need set again. It has no relation with this bit status.

Bit5~4 (SUR1~0): TM2 clock source selection bits
Bit5 Bit4
SUR1 SUR0
TM2 clock source
0 0 EXT_CLK (PA4)
0 1 Crystal mode OSC1
1 0 RC mode (Ext. & Internal RC) OSC1
1 1 Dont use
Bit3 (EDGE): TM2 clock source edge control bit
0: increment when LH on clock
1: increment when HL on clock
Bit2~0 (PRE2~0): Set TM2 prescaler rate
Bit2 Bit1 Bit0
PRE2 PRE1 PRE0
TM2 Prescaler rate
0 0 0 1:1
0 0 1 1:2
0 1 0 1:4
0 1 1 1:8
1 0 0 1:16
1 0 1 1:32
1 1 0 1:64
1 1 1 1:128




MK7A25P

2010/09/13 Rev.06

17
B.TM2_CTL2 ($19H):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM2_CTL2 MOD PWM_OS TO_E -- POS3 POS2 POS1 POS0
Bit7 (MOD): Mode select bit.
0: TM2 work in Timer mode.
1: TM2 work in PWM mode
Bit6 (PWM_OS): Output state of PWM select bit.
0: The initial output state is H, this will change to L when TM3 timer overflow.
1: The initial output state is L, this will change to H when TM3 timer overflow.
Bit5(TO_E) : The Timer out(TO) enable/disable (pin shared with PA3)
0: Set this pin is PA3 normal I/O pin
1: Set this pin is TO (Timer output pin, frequency is TM2(PWM) counter frequency /2)
<Note> Before TO signal output, the PA3 must set as output port.

Bit3~0 (POS3~0): PWM Poscaler selection bits (Only active in PWM mode)
Bit3 Bit2 Bit1 Bit0
POS3 POS2 POS1 POS0
PWM Poscaler rate
0 0 0 0 1:1
0 0 0 1 1:2
0 0 1 0 1:3
.
.
.
.
.
.
.
.
.
.
1 1 1 0 1:15
1 1 1 1 1:16
These bits control how many times of PWM waveform output will service a PWM interrupt.
C. TM2_LA & TM2_CNT ($1AH, 1CH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM2_LA D7 D6 D5 D4 D3 D2 D1 D0
TM2_CNT D7 D6 D5 D4 D3 D2 D1 D0
<Note> TM2_CNT register is read only








MK7A25P

2010/09/13 Rev.06

18

6.2.3 TM3 (or PWM duty)
TMR3 is an 8-bits timer/counter. There are 4 registers to set its attribute.. TMR3 can be used as PWM duty
control with TM2 to do PWM waveform.
A.PWM_OPT ($1DH):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PWM_OPT PWM_OPT -- -- -- -- -- -- --
Bit7 (PWM_OPT): PWM output pin select .
0 : pwm output from PC0 (init) .
1 : pwm output from PB2 .

B.TM3_CTL ($1EH):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM3_CTL TMR3_EN WR_CNT SUR1 SUR0 EDGE PRE2 PRE1 PRE0
Bit7 (TM3_EN): TMR3 enable bit.
0: TM3 disable.
1: TM3 enable.
<Note> When TM2_CTL2 is set to PWM mode, this bit will be inhibited. The TM3 became duty counter of
PWM waveform.
Bit6 (WR_CNT): Latch buffer data write to counter register enable/disable.
0: Latch buffer data write to counter register disable.
1: Latch buffer data write to counter register enable
<Note> This bit is set only in the initial state of new timer/counter data to let latch buffer data write to
counter register. When timer is overflow, the latch buffer data would auto reload into counter
register. User doesnt need set again. It has no relation with this bit status.
Bit5~4 (SUR1~0): TM3 clock source selection bits
Bit5 Bit4
SUR1 SUR0
TM3 clock source
0 0 EXT_CLK (PA4)
0 1 Crystal mode OSC1
1 0 RC mode (Ext. & Internal RC) OSC1
1 1 Dont use
Bit3 (EDGE): TM3 clock source edge control bit
0: increment when LH on clock
1: increment when HL on clock




MK7A25P

2010/09/13 Rev.06

19


Bit2~0 (PRE2~0): Prescaler assignment bit.
Bit2 Bit1 Bit0
PRE2 PRE1 PRE0
TM3 Prescaler rate
0 0 0 1:1
0 0 1 1:2
0 1 0 1:4
0 1 1 1:8
1 0 0 1:16
1 0 1 1:32
1 1 0 1:64
1 1 1 1:128


C. TM3_LA & TM3_CNT ($20H,22H)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TM3_LA D7 D6 D5 D4 D3 D2 D1 D0
TM3_CNT D7 D6 D5 D4 D3 D2 D1 D0
<Note> TM3_CNT register is read only

MK7A25P

2010/09/13 Rev.06

20
6.3 PWM (Pulse Width Modulation)
PWM waveform is composed of TM2 (period) and TM3(duty). These two timers can be used as general
purpose time or PWM waveform counter by setting register. The setting flow is as following example.
Example:
ORG 000H
LGOTO MAIN ; Jump to main program.
ORG 004H ; Interrupt program start vector.
BC IRQF,b2 ; Clear PWM interrupt flag
; Users Interrupt program
RETI
ORG 050H
MAIN:
MOVLA B'XXXXXXX0' ; PC0 (PWM) has set to output.
MOVAM PC_DIR ; Set PC out
MOVLA B'01010000'
MOVAM TM2_CTL1 ; Set TM2 to Auto write and clock source is Crystal mode
OSC1.
MOVLA B'10000000'
MOVAM TM2_CTL2 ; Set TM2 to PWM mode and POS is1:1.
MOVLA 0AH ;The period is 0AH
MOVAM TM2_LA ; Set TM2_LA =0AH, WR_CNT bit=1, data will write to
TM2_CNT
MOVLA B'01010000'
MOVAM TM3_CTL ; Set TM3 WR_CNT=1 and clock source is Crystal mode
OSC1.
MOVLA 05H ;The duty is 05H
MOVAM TM3_LA ; Set TM3_LA =05H, WR_CNT bit=1, data will write to
TM3_CNT
CLR IRQF ; Before enable IRQM, have to clear IRQF.
MOVLA B'10000100'
MOVAM IRQM ; Enable INTM & TM2M interrupt.
BC TM2_CTL1,b6 ; TM2 WR_CNT=0
BC TM3_CTL ,b6 ; TM3 WR_CNT=0
BS TM2_CTL1,b7 ; Enable PWM, PC0 start output.




MK7A25P

2010/09/13 Rev.06

21
System Cl ock
PC0
TM3 counter (Duty)
TM2 counter (Peri od)
(n+1)
(N+1)
(n+1) (n+1)
(N+1)


6.4 Capture
The capture function provides waveform measurement. The setting flow is as blow:
(a) User should set CONFIG register at first, setting EXT_CLK (bit 8) to 1, let PA4 as capture input pin.
(b) Set TM1 prescaler rate and capture condition (polarity and edge). Then enable capture interrupt.
(c) Capture interrupt is occurred. The length of captured waveform will be latched at TM1L_LA and
TM1H_LA.
Example1: Capture a cycle (two rising edge) and use interrupt (ENC=0, auto clear counter)
ORG 000H
LGOTO MAIN ; Jump to main program.
ORG 004H ; Interrupt program start vector.
BC IRQF,b1 ; Clear TM1 interrupt flag
COM TM1L_LA,a ;Read low-byte data (FFH - low register data)
MOVAM 40H ;Save data to RAM
COM TM1H_LA,a ;Read high-byte data (FFH high register data)
MOVAM 41H ;Save data to RAM
MOV TM1H_LA,a

RETI
ORG 050H
MAIN:
MOVLA B'XXX1XXXX'
MOVAM PA_DIR ;set PA4 INPUT
MOVLA B'00110001'
MOVAM TM1_CTL1 ; Capture mode enable, TM1 Prescaler rate 1:2.
CLR IRQF ; Before enable IRQM, have to clear IRQF.
MOVLA B'10000010'
MOVAM IRQM ; Interrupt function enable, TM1 Interrupt enable.
BS TM1_CTL1,b7 ; Start Capture function.


PWM waveform

MK7A25P

2010/09/13 Rev.06

22
System Cl ock
PA4
TM1 counter
t

Example2: Capture a cycle (two rising edge) without using interrupt (ENC=0, auto clear counter)
MOVLA B'XXX1XXXX'
MOVAM PA_DIR ;set PA4 INPUT
CLR IRQF
MOVLA B'10110000'
MOVAM TM1_CTL1 ; Capture mode enable, TM1 Prescaler rate 1:1.

Loop: ; A waiting for Capture Flag enable loop.
BTSC IRQF,b1 ; Consider this bit to know Flag is set or not.
LGOTO Cap_part ; If Flag is 1 then jump to read preload register
LGOTO Loop ; If Flag is 0 then jump to Loop
Cap_part: ; Read preload register after Captured
CLR IRQF
COM TM1L_LA,a ; Read low-byte data (FFH - low register data)
MOVAM 40H ; Save data to RAM
COM TM1H_LA,a ; Read high-byte data (FFH - high register data)
MOVAM 41H ; Save data to RAM
LGOTO Loop

Example3: Capture a pulse width and use interrupt (ENC=0, auto clear counter)
ORG 000H
LGOTO MAIN
ORG 004H
BC IRQF,b1 ; Clear TM1 interrupt flag
BTSC TM1_CTL1,b3 ; Consider this bit to know which edge is happen.
LGOTO Fall_edge ; If now is rise edge interrupt, jump to Fall_edge part to set
control register to measure rise-fall edge length. If now is fall
edge interrupt, read data.
BS TM1_CTL1,b3

RETI
Fall_edge:
BC TM1_CTL1,b3 ; Set control register to capture interrupt happen at PA4

MK7A25P

2010/09/13 Rev.06

23
rise-edge.
COM TM1L_LA,a ; Read low-byte data (FFH - low register data)
MOVAM 40H ; Save data to RAM
COM TM1H_LA,a ; Read high-byte data (FFH - high register data)
MOVAM 41H ; Save data to RAM
RETI
ORG 050H
MAIN:
MOVLA B'XXX1XXXX'
MOVAM PA_DIR ;set PA4 INPUT
MOVLA B'00110000'
MOVAM TM1_CTL1 ; Capture mode enable. Capture interrupt service at PA4 rise
edge. TM1 Prescaler rate 1:1.
CLR IRQF ; Before enable IRQM, have to clear IRQF.
MOVLA B'10000010'
MOVAM IRQM ; Interrupt Function enable, TM1 Interrupt enable
BS TM1_CTL1,b7
; Users program
System Cl ock
PA4
TM1 counter
t


Example1: Capture a cycle (one rising edge) and use interrupt (ENC=1, clear counter by software)
ORG 000H
LGOTO MAIN ; Jump to main program.

ORG 004H ; Interrupt program start vector.
BC IRQF,b1 ; Clear TM1 interrupt flag
MOV TM1H_LA,a ;Read high-byte data
SUB OLD_HDATA,a ;Old_hdata New_hdata(a)
MOVAM SUM_H ;Save high byte length
SUB LENGTH,a ;Check high_byte length =set value ?(check bounce)
BTSS STATUS,b2 ;Yes : complete , No= continue counter
LGOTO INTR
MOV TM1L_LA,a ;Read low-byte data
SUB OLD_LDATA,a ;Old_ldata New_ldata(a)

MK7A25P

2010/09/13 Rev.06

24
MOVAM SUM_L ;Save low byte length
BTSS STATUS,b0 ;Check havent borrow (C=1?)
DEC SUM_H,m ; If C=0 (borrow), SUM_H 1
INTR:
RETI

ORG 050H
MAIN:
MOVLA B'XXX1XXXX'
MOVAM PA_DIR ;set PA4 INPUT
MOVLA B'00110000'
MOVAM TM1_CTL1 ; Capture mode enable, TM1 Prescaler rate 1:1.
CLR IRQF ; Before enable IRQM, have to clear IRQF.
MOVLA B10000010
MOVAM IRQM ; Interrupt function enable, TM1 Interrupt enable.
MOV CLR_CNT,m ; Clear counter
MOV TM1L_LA,a
MOVAM OLD_LDATA ;Save low-byte data to register
MOV TM1H_LA,a
MOVAM OLD_HDATA ;Save high-byte data to register
MOVLA 05H ;Set capture length =05
MOVAM LENGTH ;Save length to register
BS TM1_CTL1,b7 ; Start Capture function.


PA4
System Clock
IRQ
T =0535H
Check high_byte <05H





MK7A25P

2010/09/13 Rev.06

25

6.5 WDT (Watchdog Timer)
WDT is a timer to prevent software from malfunction or jumping to an unknown location with unpredictable
result. The source clock of WDT is an independent internal RC oscillator. This timer would be affected by
temperature, voltage and different production lot.
A.WDT_CTL ($3DH):
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
WDT_CTL WDTEN i_WDT i_STAB -- -- PRE 2 PRE 1 PRE0
Bit7 (WDTEN): Watchdog timer Enable bit
0: WDT disable.
1: WDT enable.
Bit6 (i_WDT): i_WDT wakeup enable bit ,in this mode , pin change wakeup(PA7)disable .
0: i_WDT disable.
1: i_WDT enable.
Bit5 (i_STAB): i_STAB wakeup times(in i_WDT mode)set bit .
0: wakeup times=1.25ms(init) .
1: wakeup times=625us

Bit2~0 (PRE2~0): Set Prescaler rate. All the data are not accurate because it is RC OSC.
Bit2 Bit1 Bit0
PRE2 PRE1 PRE0
WDT Prescaler rate
0 0 0 20mS
0 0 1 40mS
0 1 0 80mS
0 1 1 160mS
1 0 0 320mS
1 0 1 640mS
1 1 0 1.28S
1 1 1 2.56S










MK7A25P

2010/09/13 Rev.06

26
6.51 i_WDT wakeup flow

WDT-Wakeup :
(Watch-dog timer wake-up)
Set Config :
WDTE(bit4)=enable
Set Register:
WDT_CTL($3D)
bit7=enable(wdten),
bit6=disable(i_WDT)
.
.
.
SLEEP
NOP
Wait
(20ms*N sleep
time+20ms clk
stabletime)
(N=1~128)
SystemReset
i_WDT-Wakeup :
(Internal watch-dog timer
wake-up)
Set Config :
WDTE(bit4)=enable
Set Register :
WDT_CTL($3D)
bit7=enable(wdten),
bit6=enable(i_WDT),
Bit5=0(1.25ms), 1(625us)
novla 90H
movam IRQM
bc IRQF,4
.
.
SLEEP
NOP
Wait
(20ms*N sleep
time+1.25ms(or 625us)
clk stabletime)
(N=1~128)
Org 004H (IRQ vector)
bc IRQF,4
IRETI
Next(sleep)instruction
NOP
.
* CLRWDT
.
.
*When wakeup must
CLRWDT, otherwise watch-
dog timer will keep operation
start
clrwdt
movla 87h ; sleep time=2.56s,
wakeup time=20ms
.
.
.
Sleep
nop
System reset
start
clrwdt
movla E7h ; sleep time=2.56s,
wakeup time=1.25ms(bit5=1)
.
.
.
Sleep
nop
clrwdt
.
movam WDT_CTL($3D)
movam WDT_CTL($3D)
ORG 004H
bc IRQF,4
IRETI


MK7A25P

2010/09/13 Rev.06

27


6.6 Reset
There are 4 events will cause reset which is listed as below. The power-down event will cause MK7A25P reset
and the detected voltage is according to the bit6~bit5 in the CONFIG register. This condition is used to protect
chip in deficient power environment. The last two cases are called warm reset. The different reset events will
affect registers and RAM. The TO and PD bits can be used to determine the type of reset.

(1) Power-on reset.
(2) Low voltage reset (LVR).
(3) RESETB pin reset (input a negative pulse).
(4) WDT timer overflow reset.
Power on reset
Low vol tage reset
RESETB pi n
Watchdog Ti mer
WDT
overfl ow
Synchroni ze wi th ri ppl e counter
System Cl ock
Del ay for setup ti me
Internal speci fi c RC
OSC
RESET


<Note>: the watchdog setup time is approximately 20ms that will has some tolerance due to power voltage,
process and temperature variations. Setup tim

The default value during different reset condition
Address Name Cold Reset Warm Reset
N/A Accumulator xxxx xxxx pppp pppp
00H INDF 0000 0000 0000 0000
01H PCL 0000 0000 0000 0000
02H PCH - - - - -000 - - - - -000
03H STATUS 0001 1xxx 0001 1xxx
04H FSR xxxx xxxx pppp pppp
05H PA_DIR 1111 1111 1111 1111
06H PA_DAT xxxx xxxx pppp pppp
07H PB_DIR xxxx 1111 xxxx 1111
Figure: System Reset Block

MK7A25P

2010/09/13 Rev.06

28
08H PB_DAT xxxx xxxx xxxx pppp
09H PC_DIR xx11 11x1 xx11 11x1
0AH PC_DAT xxxx xxxx xxpp ppxp
13H TM1_CTL1 0000 0000 0000 0000
14H TM1L_LA 1111 1111 1111 1111
15H TM1H_LA 1111 1111 1111 1111
16H TM1L_DAT 1111 1111 1111 1111
17H TM1H_ DAT 1111 1111 1111 1111
18H TM2_CTL1 0000 0000 0000 0000
19H TM2_CTL2 0000 0000 0000 0000
1AH TM2_LA 1111 1111 1111 1111
1CH TM2_DAT 1111 1111 1111 1111
1DH PWM_OPT 0xxx xxxx 0xxx xxxx
1EH TM3_CTL 0000 0000 0000 0000
1FH TM1_CTL2 0000 0000 0000 0000
20H TM3_LA 1111 1111 1111 1111
22H TM3_DAT 1111 1111 1111 1111
25H IRQM 00x0 000x 00x0 000x
2
26H IRQF x0x0 000x x0x0 000x
29H AD_CTL1 0x0x xx00 0x0x xx00
2
2AH AD_CTL2 0xxx xx00 0xxx xx00
2
2BH AD_CTL3 xxxx x000 xxxx x000
2
2CH AD_DAT_L 00xx xxxx 00xx xxxx
2DH AD_DAT_H 0000 0000 0000 0000
31H PA_PLU 0000 0000 0000 0000
33H PB_PLU 0000 0000 0000 0000
35H PC_PLU 0011 0000 0011 0000

3AH WAKEUP 0000 0000 0000 0000
3DH WDT_CTL 100x x111 100x x111
3EH TAB_BNK xxxx x000 xxxx x000
3FH SYS_CTL 0xxx xx00 0xxx xx00
X: unknown; ?: value depends on condition ;
P: previous data; -:unimplemented and read as 0 .





MK7A25P

2010/09/13 Rev.06

29

6.7 Interrupt
The MK7A25P provides 8 external interrupt (PA0~7), three internal timer/event counter interrupt and an A/D
converter interrupts. IRQM and IRQF registers are used to control or declare request state of all interrupts.
The external interrupt is triggered by signal toggle of PA0~7 and the related interrupt request flag (PAF; bit4
of IRQF) will be set. The A/D converter interrupt is initialized by setting the A/D converter request flag (ADCF;
bit 6 of IRQF) ,interrupt is occurred by end of A/D conversion.
IRQM is used to enable/disable interrupt and IRQF is used to indicate which interrupt is occurred. If the
specific IRQM doesnt enable then the hardware interrupt would not occurred. But the IRQF will response the
status no matter how IRQM enable or not. For example, user enable TM1 to start counting. If IRQM bit 1 is
enabled, the hardware interrupt would generate when timer overflow and IRQF bit 1 will be set. At the same
time, program will jump to interrupt vector. User should clear IRQF in interrupt service routine, otherwise the
interrupt would not work properly. Another condition is if IRQM bit 1 is disabled, the interrupt would not
generate when timer overflow, but IRQF bit 1 still will be set. Program would not jump to interrupt vector.
A. IRQM ($25H)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
IRQM INTM ADCM -- PAM TM3M TM2M/PWM TM1M/CAPT --
Bit7 (INTM): Global enable bit.
0: Disable. All interrupts are mask.
1: Enable. All interrupt are unmask
When interrupt is serving, the INTM will reset to 0 to prevent the other interrupt happen. After
served, the IRETI instruction will set INTM as 1.
Bit6 (ADCM): ADC end of conversion (EOC) interrupt enable:
0: Disable Interrupt
1: Enable Interrupt
Bit4 (PAM): PA interrupt enable.
0: Disable Interrupt
1: Enable Interrupt
Bit3 (TM3M): TM3 interrupt enable
0: Disable Interrupt
1: Enable Interrupt
Bit2 (TM2M/PWM): TM2/PWM interrupt enable
0: Disable Interrupt
1: Enable Interrupt
Bit1 (TM1M/CAPT): TM1/Capture interrupt enable
0: Disable Interrupt
1: Enable Interrupt


MK7A25P

2010/09/13 Rev.06

30

B. IRQF ($26H)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
IRQF -- ADCF -- PAF TM3F TM2F/PWM TM1F/CAPT --
Bit6 (ADCF): ADC end of conversion interrupt request flag:
0: End of conversion interrupt request off
1: End of conversion interrupt request on
Bit4 (PAF): PA0~7 Interrupt request flag:
0: PA interrupt request off
1: PA interrupt request on
Bit3 (TM3F): TM3 Interrupt request flag
0: TM3 overflow interrupt request off
1: TM3 overflow interrupt request on
Bit2 (TM2F/PWM): TM2/PWM interrupt request flag
0: TM2 overflow interrupt request off
1: TM2 overflow interrupt request on
Bit1 (TM1F/CAPT): TM1/Capture Interrupt flag
0: TM1 overflow or Capture interrupt request off
1: TM1 overflow or Capture interrupt request on

6.7.1 External interrupt / Wake up function
Port A (PA) provide external interrupt and wake up function. When device is not in sleep mode, the PA
input single will serve as external interrupt. When external interrupt is occurred, program will jump to 004H
(Interrupt vector). If device is in sleep mode, the PA input single will serve as wake up function. When wake
up single input, device will let system clock work at first. Then wait for wake up time 20ms. After that,
program will jump to 004H. The below flow chart describe how to set port A to work as external interrupt or
wake up function.


MK7A25P

2010/09/13 Rev.06

31
PortA Wake_up :
MOVLA FFH
MOVAM PA_DIR
(set portA is input)
MOVLA 90H
MOVAM IRQM
(set global&PA irq enable)
BC IRQF,b4
(Clear PA irq flag)
MOV PA,a
(read PB status)
MOVLA 01H
MOVAM WAKEUP
(set PA0 is external interrupt)
ORG 004H
:
:
BC IRQF,b4
RETI
PortA External interrupt :
MOVLA FFH
MOVAM PA_DIR
(set portA is input)
MOVLA 90H
MOVAM IRQM
(set global&PA irq enable)
BC IRQF,b4
(Clear PA irq flag)
MOV PA,a
(read PA status)
MOVLA 01H
MOVAM WAKEUP
(set PA0 is pin wake_up)
ORG 004H
:
:
BC IRQF,b4
RETI
BTSS IRQF,4
SLEEP
NOP
When Pin change Occurred ,
into the interrupt vector






MK7A25P

2010/09/13 Rev.06

32
6.8 ADC
The MK7A25P provide 4 channels and 10-bit resolution A/D converter. The A/D converter contains 5
registers which are AD_CTL1 (29H), AD_CTL2 (2AH), AD_CTL3 (2BH), AD_DAT_L(2CH)and
AD_DAT_H (2DH).
A. AD CTL1 ($29H)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_CTL1 EN -- MODE -- -- -- CHSEL1 CHSEL0
Bit7 (EN): ADC enable bit
0: ADC disable.
1: ADC enable.
<Note> When end of conversion, this bit will reset to 0.
Bit5 (MODE): ADC mode select bit
0: ADC channels work as A/D conversion.
1: ADC channels work as comparator
<Note> (a) If this bit is 1, Vin data will compare with AD_DAT. The results are stored at the AD_CTL2 Bit7.
If this bit is 0, the Vin was converted into 8-bit digital data and saved in AD_DAT register.
(b) Vin: Input voltage from ADC channel
Bit1~0 (CHSEL1~0): ADC input channel select bits
Bit1 Bit0
CHSEL1 CHSEL0
Input channel
0 0 Channel 0, PB0
0 1 Channel 1, PB1
1 0 Channel 2, PB2
1 1 Channel 3, PB3



B. AD_CTL2 ($2AH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_CTL2 RSUT -- -- -- -- -- CKSEL1 CKSEL0
Bit7 (RSUT): Compare mode result bit.
0: Vin AD_DAT.
1: Vin AD_DAT






MK7A25P

2010/09/13 Rev.06

33
Bit1~0 (CKSEL1~0) : ADC Conversion clock source select bits
Bit1 Bit0
CKSEL1 CKSEL0
Conversion clock
0 0 System clock X2
0 1 System clock X8
1 0 System clock X32
1 1 System clock X128
<Note> The conversion clocks decide the conversion rate and precision. If fast conversion clock is
selected, that will drop-off the precision. If user want to get more accurate A/D data, use slow
speed is recommended.

C. AD_CTL3 ($2BH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_CTL3 -- -- -- -- -- PBSEL2 PBSEL1 PBSEL0
Bit2~0 (PBSEL2~0): ADC Channel input mode select bits
Bit2 Bit1 Bit0
PBSEL2 PBSEL1 PBSEL0
PB3~PB0 configurations
0 0 0 PB3, PB2, PB1, PB0
0 0 1 PB3, PB2, PB1, AN0
0 1 0 PB3, PB2, AN1, AN0
0 1 1 PB3, AN2, AN1, AN0
1 X X AN3, AN2, AN1, AN0
<Note> To minimize power consumption, all the I/O pins should be carefully managed before entering
sleep mode.

D. AD_DAT_L (2CH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_DAT_L D1 D0 -- -- -- -- -- --

E. AD_DAT_H (2DH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
AD_DAT_H D9 D8 D7 D6 D5 D4 D3 D2
<Note> This register has two different usage. If work in compare mode, this data will compare with input
voltage from ADC channel. In ADC mode, the registers stored the ADC conversion data.




MK7A25P

2010/09/13 Rev.06

34
Example :
LOOP1
BTSC AD_CTL1,b7 ; Check A/D complete?
BC IRQF,b6 ; Clear A/D Flag ;
MOVLA 03H
MOVAM AD_CTL1 ; set PB3 is A/D input ;
MOVAM AD_CTL2 ; set A/D clk=sys_clk/128;
MOVLA 04H
MOVAM AD_CTL3 ; set PB0~PB3 is analog input ;
BS AD_CTL1,b7 ; Start A/D Transfer ;
CHECK_FLAG
BTSS IRQF,b6 ; Check A/D flag=1 ? ;
LGOTO CHECK_FLAG
MOVLA AD_DAT,a
MOVAM 40H ; Read A/D data to RAM


MK7A25P

2010/09/13 Rev.06

35

Fig. ADC Setting Flow
START
Bit 7 of AD_CTL1
= 0 ?
No
Yes


Clear Bit 6 of IRQF
(Clear AD Flag )
Set AD Register
(AD_CTL1~3)
Bit 7 of AD_CTL1=1
(Start AD Covert )
Bit 6 of IRQF
= 1 ?
(AD end of converting )
No
Yes
Read AD Data

MK7A25P

2010/09/13 Rev.06

36
6.9 Table Look-up Function
The MK7A25P provide table look-up function. The look-up tables can be placed at any location in the ROM
space. The instruction of TABRDL is to read low byte of ROM table. And The TABRDH is to read high byte.
The register of TAB_BNK is used to define address of high bit (MSB) of table location (3+8=11bits-address
bit, 2
11
=2Kbytes-data byte).

6.9.1 TAB_BNK ($3EH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TAB_BNK -- -- -- -- -- BANK2 BANK1 BANK0
Bit2~0 (BANK2~0): High byte Table location select bits
Bit2 Bit1 Bit0
BANK2 BANK1 BANK0
BANK select
0 0 0 000 XXXX XXXX Table location
0 0 1 001 XXXX XXXX Table location
0 1 0 010 XXXX XXXX Table location
. . . .
1 1 1 111 XXXX XXXX Table location

6.9.2 Table look up Example program
The main function of below program is table looking-up. The results of TABRDL and TABRDH will be 55H
and AAH (Address is 0704H).

#DEFINE TAB_BNK 3EH ; Define address 3EH of RAM named TAB_BNK

BUFA EQU 43H ; Define address 43H of RAM named BUFA

(address) ORG 0700H ; Program start from 0700H of ROM
0700H MOVLA 00H ; Save 00H to A register
0701H DW 1122H ; Store 1122H at 0701H of ROM
0702H DW 3344H ; Store 3344H at 0702H of ROM
0703H DW 6677H ; Store 6677H at 0703H of ROM
0704H DW 55AAH ; Store 55AAH at 0704H of ROM

MOVLA 04H ; Save 04H to A register (low bit address)
MOVAM BUFA ; Save A registers value to BUFA
MOVLA 0FH ; Save 0FH to A register (high bit address)
MOVAM TAB_BNK ; Save A registers value to TAB_BNK
TABRDL BUFA ; Looking-up the Low-byte value of TAB_BNK and BUFA
pointed address, saved it to A register.

TABRDH BUFA ; Looking-up the High-byte value of TAB_BNK and BUFA
pointed address, saved it to A register.

MK7A25P

2010/09/13 Rev.06

37
6.10 System Control
The MK7A25P provide Auto-Bank function and dual clock operation mode. When Sequence administers
jumping, system will auto save the high byte of PC to prevent carry over error of PC that is Auto-Bank means.
The dual clock mode has internal RC and external crystal clock source. User can use both of two in same
time. For example, internal RC (4MHz) used to be system clock source, external crystal (32KHz) to be
counter clock source. Because of external crystal is very accurate, User can get a very exact timer.

6.10.1 SYS_CTL ($3FH)
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SYS_CTL CLKS -- -- -- -- -- STP1 STP0
Bit7 (CLKS): System clock source select bit. Only active in dual clock mode.
Dual clock mode:
0: System clock is Internal RC
1: System clock is OSC (crystal).
Single clock mode:
Dont use.
Bit1 (STP1): Internal RC oscillator control bit.
Dual clock mode:
0: RC oscillation on.
1: RC oscillation off.
The other mode:
Dont use.
<Note> Before setting RC oscillation off, CLKS should be switched to OSC oscillation at first.
Bit0 (STP0): OSC (crystal) oscillator control bit
Dual clock mode:
0: OSC oscillation on.
1: OSC oscillation off.
The other mode:
Dont use.
<Note> Before setting OSC oscillation off, CLKS should be switched to RC oscillation at first.

MK7A25P

2010/09/13 Rev.06

38

6.11 Program Counter PC
The MK7A25P has an 11-bits program counter (PC) that includes PCL (8-bits) and PCH (3bits). PC is stored
the routing of program. If user changes the value of PCL, then program will jump to the indicated location.
Ex1: PCH=01H, PCL=02H+10H=12H, the program will jump to PC=112H.
Ex2: PCH= 01H, PCL=F0H+30H=20H with carry 1, the program will jump to PC=220H but PCH still be 01H.
<Note> (a) When execute RET and RETI, RET_INT, PCH data would not be updated
(b) When execute LGOTO, LCALL and RET, PCH would be updated after mathematic operation
Example 1:
The below program is show how PCL and PCH working with direct mathematic.
#DEFINE PCL 01H ; Define address 01H of RAM named PCL
#DEFINE PCH 02H ; Define address 02H of RAM named PCH
#DEFINE ADMIN 41H ; Adminicle for PCL operation.
(address)
1C0H MOVLA HIGH P1 ; Save P1 (1C6H) High-byte address to A register
; PC=1C0H, PCL=C0H, PCH=00H
1C1H MOVAM PCH ; Save A register to PCH (To avoid jumping error at PCL
operation, store the real jumping high-byte address to PCH
at first.)
; PC=1C1H, PCL =C1H, PCH=01H.
1C2H MOVLA 4BH ; Save 4BH to A register (Address of ADDAM PCL,M is
1C5H, prepare jump to 210H, PCL have to add 210H-1C5H
=4BH)
; PC=1C2H, PCL =C2H, PCH=01H.
1C3H MOVAM ADMIN ; Ready for PCL operation.
; PC=1C3H, PCL =C3H, PCH=01H.
1C4H DEC ADMIN, a ; ADMIN 1 (The real jumping happen at 1C6H, not 1C5H.
So 1C6H+(4BH-1H) =210H)
; PC=1C4H, PCL =C4H, PCH=01H.
1C5H ADD PCL,M ; PCL add with A register, result store at PCL
; PC=1C5H, PCL =C5H, PCH=01H
P1: 1C6H NOP ; Jump to 0210H.

; PC=1C6H, PCL=C6+4AH=10H with carry in 1,the carry
will count with PCH, PCH=01H, the purpose PC high
byte address will be PCH + PCLs carry=02H. The
program will jump to PC=210H
210H MOVLA 00H ; Purpose function part.
; PC=210H, PCL =10H, PCH=01H


MK7A25P

2010/09/13 Rev.06

39

Example 2:
The below program is show how PCL and PCH working with direct mathematic.
(address)
1C0H MOVLA 03H ; Save 03H to A register
; PC=1C0H, PCL=C0H, PCH=00H
1C1H MOVAM PCH ; Save A register to PCH
; PC=1C1H, PCL =C1H, PCH=03H.
1C2H MOVLA 4BH ; Save 4BH to A register
; PC=1C2H, PCL =C2H, PCH=03H.
1C3H MOVAM ADMIN ; Ready for PCL operation.
; PC=1C3H, PCL =C3H, PCH=01H.
1C4H DEC ADMIN, a ; ADMIN 1 (The real jumping happen at 1C6H, not 1C5H.
So 1C6H+(4BH-1H) =210H)
; PC=1C4H, PCL =C4H, PCH=03H.
1C5H ADD PCL,M ; PCL add with A register, result store at PCL
; PC=1C5H, PCL =C5H, PCH=03H
1C6H NOP ; Jump to 410H.

; PC=1C6H, PCL=C6+4AH=10H with carry in 1,the carry
will count with PCH, PCH=03H, the purpose PC high
byte address will be PCH + PCLs carry=04H. The
program will jump to PC=410H
410H MOVLA 00H ; Purpose function part.
; PC=410H, PCL =10H, PCH=03H

Example3
The below program is show how PCL and PCH working through A register
(address)
018H MOVLA 02H ; Save 02H to A register
019H MOVAM PCH ; Save A register to PCH(The purpose address is 200H, so
store 02H to PCH)
01AH MOVLA 00H ; Save 00H to A register
01CH MOVAM PCL ; Save A register to PCL(The purpose address is 200H, so
store 00H to PCL)
01DH NOP ; Jump to 200H.

200H MOVLA 00H ; Purpose function part.


MK7A25P

2010/09/13 Rev.06

40
6.12 STATUS Register
The STATUS register is an 8-bit register that contains the zero flag (Z), carry flag (C), Nibble carry flag (DC),
power down flag ( PD), and watchdog timer overflow flag ( TO). It records the status information.
Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
STATUS -- -- --
TO PD
Z DC C
Bit4 ( TO): Timer overflow flag bit
Bit3 ( PD):Power down flag bit
TO PD
Description
0 0 WDT timer overflow from sleep mode
0 1 WDT timer overflow from normal mode
1 0 Input a low at RESETB from sleep mode
1 1 Power on reset
Unchanged Unchanged Input a low at RESETB from normal mode
Bit2 (Z): zero flag bit
0: the result of a logic operation is not zero
1: the result of a logic operation is zero
Bit1 (DC): Nibble Carry and Nibble Borrow flag bit
ADD instruction:
0: no carry
1: a carry from the low nibble bits of the result occurred
SUB instruction
0: a borrow from the low nibble bits of the result occurred
1: no borrow
Bit0 (C): Carry and Borrow flag bit
ADD instruction:
0: no carry
1: a carry occurred from the MSB
SUB instruction
0: a borrow occurred from the MSB
1: no borrow

MK7A25P

2010/09/13 Rev.06

41
7. Instruction
<Note> Instruction cycle is system clock/2
JUMP INSTRUCTION
LCALL I
Call subroutine. However, LCALL can
addressing 2K address
2 None 011i iiii iiii iiii
LGOTO I Go branch to any address 2 None 010i iiii iiii iiii
LOGIC
AND M, a (M)(acc) (acc) 1 Z 1010 1000 MMMM MMMM
AND M, m (M)(acc) (M) 1 Z 1010 1001 MMMM MMMM
ANDLA I Immediate(acc) (acc) 1 Z 1111 1000 iiii iiii
COM M, a ~(M) (acc) 1 Z 1010 0100 MMMM MMMM
COM M, m ~(M) (M) 1 Z 1010 0101 MMMM MMMM
IOR M, a (M) or (acc) (acc) 1 Z 1011 1110 MMMM MMMM
IOR M, m (M) or (acc) (M) 1 Z 1011 1111 MMMM MMMM
IORLA l Immediate or (acc) (acc) 1 Z 1111 0010 iiii iiii
RL M, a
Rotate left from m to acc
m[6:0]acc[7:1]
m[7] acc[0]
1 None 1110 0000 MMMM MMMM
RL M, m
Rotate left from m to itself
m[6:0]m[7:1]
m[7] m[0]
1 None 1110 0001 MMMM MMMM
RLC M, a
Rotate left from m to acc
m[7]c
m[6:0]acc[7:1]
cacc[0]
1 C 1110 0010 MMMM MMMM
RLC M, m
Rotate left from m to itself
m[7]c
m[6:0]m[7:1]
cm[0]
1 C 1110 0011 MMMM MMMM
RR M, a
Rotate right from m to acc
m[0]acc[7]
m[7:1]acc[6:0]
1 None 1110 1000 MMMM MMMM
RR M, m
Rotate right from m to itself
M[0]m[7]
m[7:1]m[6:0]
1 None 1110 1001 MMMM MMMM
RRC M, a
Rotate right from m to acc
m[0]c,
cacc[7]
m[7:1]acc[6:0]
1 C 1110 1010 MMMM MMMM
RRC M, m Rotate right from m to itself 1 C 1110 1011 MMMM MMMM

MK7A25P

2010/09/13 Rev.06

42
m[0]c,
cm[7]
m[7:1]m[6:0]
SWAP M, a
m[7:4] acc[3:0]
m[3:0] acc[7:4]
1 None 1011 1100 MMMM MMMM
SWAP M, m m[7:4] m[3:0] 1 None 1011 1101 MMMM MMMM
XOR M, a (M) xor (acc) (acc) 1 Z 1011 0110 MMMM MMMM
XOR M, m (M) xor (acc) (M) 1 Z 1011 0111 MMMM MMMM
XORLA l Immediate xor (acc) (acc) 1 Z 1111 1001 iiii iiii
MATHEMATICS
ADD M, a (M)+(acc) (acc) 1 C, DC, Z 1010 1010 MMMM MMMM
ADD M, m (M)+(acc) (M) 1 C, DC, Z 1010 1011 MMMM MMMM
ADDC M,a (M)+(acc) + (carry) (acc) 1 C, DC, Z 1011 1010 MMMM MMMM
ADDC M,m (M)+(acc) + (carry) (M) 1 C, DC, Z 1011 1011 MMMM MMMM
ADDLA I Immediate + (acc) (acc) 1 C, DC, Z 1111 1010 MMMM MMMM
BC M, bn Clear bit n of (M) 1 None 1001 1bbb MMMM MMMM
BS M, bn Set bit n of (M) 1 None 1001 0bbb MMMM MMMM
CLRA Clear accumulator 1 Z 1010 0010 0000 0000
CLR M Clear memory M 1 Z 1010 0011 MMMM MMMM
TABRDL M
Read low byte ROM table (ROM
bank)
2 None 1101 1000 MMMM MMMM
TABRDH M
Read high byte ROM table (ROM
bank)
2 None 1101 1001 MMMM MMMM
DA M, a
Decimal Adjust M to ACC
If ACC[3:0] > 9 or DC=1
Then
ACC[3:0]ACC[3:0]+6,
DC1=~DC
else
ACC[3:0] ACC[3:0],
DC1=0
If ACC[7:4]+DC1 > 9 or C=1
Then
ACC[7:4]ACC[7:4]+6+DC1,
C=1
else
ACC[7:4] ACC[7:4]+DC1,
C=C
1 C 1101 0110 MMMM MMMM
DA M, m
Decimal Adjust M to memory
If ACC[3:0] > 9 or DC=1
Then
M[3:0]ACC[3:0]+6,
DC1=DC
else
M[3:0] ACC[3:0], DC1=0
If ACC[7:4]+DC1 > 9 or C=1
Then
M[7:4]ACC[7:4]+6+DC1,
C=1
else M[7:4] ACC[7:4]+DC1,
C=C
1 C 1101 0111 MMMM MMMM
DEC M, a (M) - 1 (acc) 1 Z 1010 1100 MMMM MMMM
DEC M, m (M) - 1 (M) 1 Z 1010 1101 MMMM MMMM
INC M, a (M) + 1 (acc) 1 Z 1011 0000 MMMM MMMM
INC M, m (M) + 1 (M) 1 Z 1011 0001 MMMM MMMM

MK7A25P

2010/09/13 Rev.06

43
MOVAM m (acc) (M) 1 None 1010 0001 MMMM MMMM
MOV M, a (M) (acc) 1 Z 1010 0110 MMMM MMMM
MOV M, m (M) (M) 1 Z 1010 0111 MMMM MMMM
MOVLA l Immediate data acc 1 None 1111 0000 iiii iiii
SUBLA I (immediate data)-(Acc)(Acc) 1 C, DC, Z 1111 0100 iiii iiii
SUB M, m (M)(acc) (M) 1 C, DC, Z 1011 0101 MMMM MMMM
SUB M, a (M) (acc) (acc) 1 C, DC, Z 1011 0100 MMMM MMMM
OTHER OPERATION
NOP No operation 1 None 1111 1111 1111 1111
CLRWDT Clear watch-dog register 1
TO , PD
1111 1111 1111 0000
RET Return (for lcall instruction ) 2 None 1111 1111 1111 0001
RETI
Return and enable INTM
( for IRQ )
2 None 1111 1111 1111 0010
RET_INT Return ( for IRQ ) 2 None 1111 1111 1111 0011
SLEEP Enter sleep (saving) mode 1
TO , PD
1111 1111 1111 100
CONDITION OPERATION
BTSC M, bn If bit n of(M)=0, skip next instruction 1 or 2 None 1000 1bbb MMMM MMMM
BTSS M, bn If bit n of (M)=1, skip next instruction 1 or 2 None 1000 0bbb MMMM MMMM
DECSZ M, a (M) - 1 (acc), skip if (acc) = 0 1 or 2 None 1010 1110 MMMM MMMM
DECSZ M, m (M) - 1 (M), skip if (M) = 0 1 or 2 None 1010 1111 MMMM MMMM
INCSZ M, a (M) + 1 (acc), skip if (acc) = 0 1 or 2 None 1011 0010 MMMM MMMM
INCSZ M, m (M) + 1 (M), skip if (M) = 0 1 or 2 None 1011 0011 MMMM MMMM
TMSS A If (acc) =0, skip next instruction 1 or 2 None 1011 1000 XXXX XXXX
TMSC M If (M) = 0, skip next instruction 1 or 2 None 1011 1001 MMMM MMMM

<Note> After SLEEP instruction, please add NOP behind it to perform transient

MK7A25P

2010/09/13 Rev.06

44

8. Electrical Characteristics
8.1 Absolute Maximum Ratings
Supply Voltage . Vss-0.3V to Vss+5.5V Storage Temperature . 40 to 125

Input Voltage Vss-0.3V to VDD+0.3V Operating Temperature 40 to 80
<Note>: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum
Ratings may cause substantial damage to the device. Functional operation of this device at other conditions
beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect
device reliability.

8.2 DC Characteristics




Test Conditions
Symbol Parameter
VDD Conditions
Min. Typ. Max. Unit
f
sys
=4MHZ 2.0 5.5
f
sys
=8MHZ 2.5 5.5 VDD Operating Voltage ---
f
sys
=12MHZ 3.3 5.5
V
3.3V 0.8
I
DD1

Operating Current
(Crystal OSC) 5V
No Load , f
sys
=4MHZ
ADC disable 1.6
mA
3.3V 0.7
I
DD2

Operating Current
(RC OSC) 5V
No Load , f
sys
=4MHZ
ADC disable 1.2
mA
I
DD3

Operating Current
(Crystal OSC)
5V
No Load , f
sys
=8MHZ
ADC disable
2.6 mA
I
DD4

Operating Current
(Crystal OSC)
5V
No Load , f
sys
=12MHZ
ADC disable
3.6 mA
V
IH
Input High Voltage 5V I/O Port 2

VDD V
V
IL
Input Low Voltage 5V I/O Port

0.8 V
WDT disable 3.5 5
5V
WDT enable 12 15
WDT disable 0.8 1.6
I
STB
Standby Current
3.3V
WDT enable 3 4
A

MK7A25P

2010/09/13 Rev.06

45




















Symbol Parameter Test Conditions Min. Typ. Max. Unit
I
IL

Input Leakage
Current
5V Vin=VDD, VSS 1 A
Voh=5V 9.9
Voh=4.5V 17.6 I
OH

I/O Port Driving
Current

5.5V

Voh=4V 24.8
mA
Vol=0.5V 24.5
Vol=0.75V 35.3
I
OL

I/O Port Sink
Current

5.5V

Vol=1V 43.8
mA
5V 70 85 100 K
R
PH
Pull-high Resistance
3.3V 120 150 180 K
V
AD
A/D input Voltage 0 VDD V
E
AD
A/D Conversion Error 2 LSB
3.3V 100
I
ADC
A/D Operating current
5V

500
uA

MK7A25P

2010/09/13 Rev.06

46
8.3 AC Characteristics




Test Conditions
Symbol Parameter
Conditions VDD
Min Typ. Max Unit
5V 32 200
f
sys1
System Clock LS Crystal mode
3V 32 200
Khz
5V 0.2 10
f
sys2
System Clock NS Crystal mode
3V 0.2 10
Mhz
5V 10 20
f
sys3
System Clock HS Crystal mode

Mhz
5V 3.6 4 4.4
f
sys4
System Clock RC mode
3V 3.6 4 4.4
Mhz
5V
T
wdt
Watchdog Timer
3V
20 mS
5V
T
rht
Reset Hold Time
3V
20 mS
T
AD
A/D clock period 3 us
T
ADC

A/D Conversion
Time
30 t
AD

T
ADCS
A/D Sampling Time 8 t
AD


5V

Voh=0.9VDD -10 mA
I
OH


Output high driving
current
3V

Voh=0.9VDD -4 mA

5V

Voh=0.1VDD 20 mA
I
OL


output low sink
current
3V

Voh=0.1VDD 8 mA

MK7A25P

2010/09/13 Rev.06

47
8.4 EXT_RC Oscillator Frequencies


MK7A21P
OSCI
Rext
Cext
VCC


The typical external RC oscillation frequency is as below table
Cext = 0.1uf (104)
Rext 5V 3V
6M 32 KHZ 30KHZ
300K 460 KHZ 450 KHZ
140K 0.97 MHZ 0.90 MHZ
68K 2.0 MHZ 1.97 MHZ
37K 3.9 MHZ 3.85 MHZ
25K 6 MHZ 6 MHZ
15K 10.3 MHZ 10 MHZ



8.5 Oscillator circuit in different mode




Crystal mode
OSC2
OSC1
C3
C2
RESETB
C 1
R 1
VDD

MK7A25P

2010/09/13 Rev.06

48



Crystal mode Crystal C2 C3
32 Khz 20~100P 20~100P LP mode
455 Khz 100P 100P
455 Khz 100P 100P
1 Mhz 20~100P 20~100P
2 Mhz 20~100P 20~100P
4 Mhz 20~100P 20~100P
8 Mhz 20~50P 20~50P
NT mode
10 Mhz 20~50P 20~50P
12 Mhz 20~50P 20~50P
16 Mhz 20~50P 20~50P
HS mode
20 Mhz 20~50P 20~50P
















RC mode
OSC2
OSC1
RESETB
C 1
R 1
VDD
C4
R2

MK7A25P

2010/09/13 Rev.06

49
9. Package Dimension

(a) 18 Pin DIP
E
eB
C
A
L
B
B1
e
D1
A
1
A
2
D
MIN NOM MAX MIN NOM MAX
A

4.57

0.180
A1 0.38

0.015

A2

3.30 3.56

0.130 0.140
B 0.36 0.46 0.56 0.014 0.018 0.022
B1 1.27 1.52 1.78 0.050 0.060 0.070
C 0.20 0.25 0.33 0.008 0.010 0.013
D 22.71 22.96 23.11 0.894 0.904 0.910
D1 0.43 0.56 0.69 0.017 0.022 0.027
E 7.62

8.26 0.300

0.325
E1 6.40 6.50 6.65 0.252 0.256 0.262
e

2.54

0.100

L 3.18

0.125

eB 8.38

9.65 0.330

0.380
DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES
SYMBOLS
PIN 1INDICATOR 0.039
TOP E-PIN INDENT 0.079
E
1
BOTTOM E-PIN INDENT 0.118
0.727


MK7A25P

2010/09/13 Rev.06

50
(b) 18 Pin SOP
1
.
5
2
4
1.270
TOP 1.0x0.10~0.15DP
BTM2.00
(
T
O
P
7
.
4
4
3

0
.
0
5
)
(
B
T
M
7
.
4
9
3

0
.
0
5
)
1
0
.
3
1

0
.
1
0
(TOP11.5070.05)
(BTM11.5570.05)
0.406 1.270
0
.
1
7
7
8

0
.
0
5
1
.
0
4
1

0
.
0
2
5
2
.
3
3
7

0
.
0
5
2
.
5
1
5

0
.
1
SEAING PLANE
0.05
0.508X45
0
.
2
5
4
0.7620.076
5
3X
3

10(T
Y
P)


MK7A25P

2010/09/13 Rev.06

51

(c) 14 Pin DIP
D
E
1
TOP E-PIN INDENT 0.079
BOTTOM E-PIN INDENT 0.118
A
L
B B1 e
D1
A
1
A
2
E
eB
C
MIN NOM MAX MIN NOM MAX
A

4.57

0.180
A1 0.38

0.015

A2 3.25 3.30 3.45 0.128 0.130 0.136
B 0.36 0.46 0.56 0.014 0.018 0.022
B1 1.27 1.52 1.78 0.050 0.060 0.070
C 0.20 0.25 0.33 0.008 0.010 0.013
D 18.90 19.15 19.30 0.744 0.754 0.760
D1 1.07 1.19 1.32 0.042 0.047 0.052
E 7.62

8.26 0.300

0.325
E1 6.35 6.50 6.65 0.250 0.256 0.262
e

2.54

0.100

L 3.18

0.125

eB 8.64

9.65 0.340

0.380
DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES
SYMBOLS


MK7A25P

2010/09/13 Rev.06

52
(d) 14 Pin SOP
A A
2
A
1
B
e
y
7 (4X) MIN NOM MAX MIN NOM MAX
A 1.35 1.60 1.75 0.053 0.063 0.069
A1 0.10

0.25 0.004

0.010
A2

1.45

0.057

B 0.33

0.51 0.013

0.020
C 0.19

0.25 0.007

0.010
D 8.55

8.75 0.337

0.344
E 3.80

4.00 0.150

0.157
e

1.27

0.050

H 5.80

6.20 0.228

0.244
L 0.40

1.27 0.016

0.050
Y

0.10

0.004
0

8 0

8
DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES
SYMBOLS
H E
D
L
C


MK7A25P

2010/09/13 Rev.06

53
<Important Notice>
Mikkon products are not designed, intended, authorized or warranted for use as
components in systems, or equipment intended for surgical implantation, atomic energy
control instruments, airplane or spaceship instruments, transportation instruments, traffic
signal instrument, combustion control instruments, or for other applications intended to
support or sustain life. Further more, Mikkon products are not intended for applications
wherein failure of Mikkon products could result or lead to a situation wherein personal injury,
death or severe property or environmental damage could occur.
Mikkon customers using or selling these products for use in such applications do so at their
own risk and agree to fully indemnify Mikkon for any damages resulting from such improper
use or sales.