Corporation: Seamless Pipe

Corporation
SEAMLESS PIPE
Pipe Applicable Standards

ASTM Pipe Code Designations
A 106/A 106M
A 312/A 312M
A 333/A 333M
A 335/A 335M
Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
(GRADE P5, P9, P11, P22, P91)
ASTM Standards
A 370
A 530/A530M
A 999/A999M
E 23
E 165
E 213
E 309
E 381
E 709
Test Methods and Definitions for Mechanical Testing of Steel Products

Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
Specification for General Requirements for Alloy and Stainless Steel Pipe
Test Methods for Notched Bar Impact Testing of Metallic Materials
Test Method for Liquid Penetrant Examination
Practice for Ultrasonic Examination of Metal Pipe and Tubing
Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation
Method of Macroetch Testing Steel Bars, Billets,Blooms, and Forgings
Guide for Magnetic Particle Examination
ASME Standards
B36.10M
B36.19M
Welded and Seamless Wrought Steel Pipe

Stainless Steel Pipe
Other Standards
SSPC-SP 6
SNT-TC-1A
SAE J 1086
Surface Preparation Specification No. 66

Recommended Practice for Nondestructive Personnel Qualification and Certification
Practice for Numbering Metals and Alloys (UNS)
Test and Inspection

Chemical Analysis
Mechanical Test
(Tensile, Impact, Hardness, etc)
Hydrostatic Test
Visual and Dimension Inspection
Ultrasonic Test
(Longitudinal and Transverse, Wall Thickness, Lamination)
HSE
We recognize that health, safety and environment are very important factor of
management and all TK employees will perform the followings to;
1. Comply all the rules and regulations of environment protection.
2. Do our continuous effort to improve our safe working condition.
3. Design and manufacture the products for our customers to use safely.
To perform this policy effectively, we will educate all the employees in regular basis
and further, we will announce this policy to all our customers to show our
willingness and the performance of HSE management intension.
Manufacture Process
Pipe
Coating Lubricant
(Inside Surface)
Extrusion
Heat Treatment
Ultrasonic
Examination
End Cutting
Surface Grinding
(Outside & Inside)
Straightening/
Sizing
Machining
Visual & Dimension

Inspection
Measurement of Length &

Weight
Marking & Coating
Shipping
PMI & Final

Inspection
Seamless Pipe Available Size Ranges
Carbon Steel & Alloy Steel
(in millimeters)
Thick.
9.5
12.7
14.3
15.9
17.0
17.5
20.6
23.8
26.0
26.2
31.0
35.0
37.0
45.0
46.0
47.6
O.D
457.2
508.0
558.8
609.6
660.4
711.2
762.0
812.8
863.6
914.4
O.D 660.4 and over, length shall be negotiated between manufacturer and purchaser.
Stainless Steel
(in inches)
Sch.
S5S
N.P.S
18
20
22
24
S10S
S10
S20
S30
S40S
STD
S40
S60
S80S
XS
S80
S100 S120 S140 S160
Quality Control Activity

INITIAL MATERIALS INSPECTION
WELDING
Welder Qualify
Welding Materials Control
Dimensional Check
Visual Check
Chemical Composition & Mechanical Properties Test
Impact Test
PROOF TEST
IN-PROCESS INSPECTION
Traceability Control
TK
corporation
Hydrostatic Test
HEAT TREATMENT
FINAL INSPECTION
Coating Wall Thickness
& Marking Check
Dimensional Check
Surface Condition Check
Heat Treatment Chart
NON-DESTRUCTIVE EXAMINATION
Ultrasonic Test
Radiographic Test
Liquid Penetrant Test
Magnetic Particle Examination
Permissible Variation in accordance with ASTM A999/A999M.

1. Outside Diameter
2. Wall Thickness
3. Length
4. Mass(Weight)
A S M E Welding End Preparation
(in inches)
Nominal Pipe Wall
Thickness(t)
End Preparation
All Thickness
as in sketch "a" above (Note 1)
7/8 and less
as in sketch "b" above (Note 2)
more than 7/8
as in sketch "c" above (Note 2)
Notes : 1. Unless otherwise specified, the expending pipe shall be furnished with plain ends.
2. When ordered on Bevel Ends, TK can be furnished with various bevel ends. For example ASME
B 16.25, JIS B 2312 excetera.
Hydrostatic Test
1. If required by the applicable product specification or the purchase order, the pipe shall be tested by the
hydrostatic test
2. The test pressure or stress shall be determined using the following equation :
P = 2St/D or S = PD / 2t
where:
P = hydrostatic test pressure in psi or [MPa]
S = pipe wall stress in psi or [MPa]
t = specified wall thickness, nominal wall thickness according to specified ASME schedule
number. or 1.143 times the specified minimum wall thickness, in.[mm], and
D = specified outside diameter, outside diameter corresponding to specified ASME pipe size, or
outside diameter calculated by adding 2t (as defined above) to the specified inside diameter,
in.[mm].
Certificates
Head Office
1499-1, SongJeong-Dong, Gangseo-Gu, Busan, Korea
Tel : 82-51-970-6600
Fax : 82-51-831-5599
E-mail : tkbend@tkbend.co.kr
http://www.tkbend.co.kr
Export & Import Subsidiary Company
DaeShin Co., Ltd.
801 Jeong-Sun BLDG, 1270-1, Jwa-Dong
Haeundae-Gu, Busan, Korea
Tel : 82-51-747-8103~8
Fax : 82-51-747-8444~5
E-mail : yjk@tkbend.co.kr
http://www.tkbend.co.kr

Corporation: Seamless Pipe

Uploaded by

Copyright:

Available Formats

Corporation: Seamless Pipe

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Corporation: Seamless Pipe

Uploaded by

Copyright:

Available Formats

Corporation

Pipe Applicable Standards

(GRADE P5, P9, P11, P22, P91)

Test Methods and Definitions for Mechanical Testing of Steel Products

Welded and Seamless Wrought Steel Pipe

Surface Preparation Specification No. 66

Test and Inspection

Visual & Dimension

Measurement of Length &

Marking & Coating

PMI & Final

Seamless Pipe Available Size Ranges

Carbon Steel & Alloy Steel

S100 S120 S140 S160

Quality Control Activity

Heat Treatment Chart

Permissible Variation in accordance with ASTM A999/A999M.

A S M E Welding End Preparation

as in sketch "a" above (Note 1)

7/8 and less

as in sketch "b" above (Note 2)

more than 7/8

as in sketch "c" above (Note 2)

You might also like