Type NR Neutral Grounding Resistors

APPLICATION

Neutral Grounding Resistor

Powerohm Type NR Neutral Grounding Resistors are used

in industrial power systems for resistance grounding of wyeconnected generators and transformers. A neutral grounding resistor limits the fault current to a value which is
sufficient enough to operate protective relays, yet prevent
unwanted fault damage.

Neutral Grounding Resistor Schematic

Transformer or Generator
Secondary
N
To Protective
Relay

CT
R

Neutral Grounding
Resistor
G

DESIGN REQUIREMENTS
Neutral grounding resistors are rated in line-to-neutral
voltage (system voltage divided by 1.732), initial fault
current and maximum time on. Powerohm neutral grounding resistors are designed to dissipate the required amount
of energy and not exceed the temperature limitations of
IEEE Standard 32-1972. As defined in this publication,
the time and temperature ratings for neutral grounding
resistors are as follows:
Short time: Short time ratings are 10 and 60 seconds.
Since short time rated resistors can only withstand rated
current for short periods of time, they are usually used with
fault clearing relays. The short time temperature rise for
the resistive element is 760C.
Extended time: A time on rating greater than ten minutes
which permits temperature rise of resistive elements to
become constant, but limited to an average not more than
90 days per year. The extended temperature rise for the
resistive element is 610C.
Continuous: Capable of withstanding rated current for
an indefinite period of time. The continuous temperature
rise for the resistive element is 385C.

POWEROHM
RESISTORS, INC.

BASIC CONSTRUCTION
Resistor Assembly: The resistor coils consist of a stainless
steel edgewound element wound around a ceramic core
supported on a through-rod. Glazed insulators are attached
to each end of the coils and fastened to a heavy gage,
corrosion resistant frame. The unit is designed to permit the
expansion of supporting rods when submitted to high operating temperatures. Resistor elements are joined by stainless steel connectors, which are welded in place, to form a
positive electrical path.
Safety Enclosure: Our resistor assemblies are available
with grounded safety enclosures to protect personnel and
wildlife from harm. Screened and louvered enclosures are
available in a variety of finishes including painted, powder
coated, mill galvanized, hot-dipped galvanized, aluminum
and stainless steel.
Options: A number of additional options are available
including entrance bushings, current transformers, elevating stands and disconnect switches.

ELECTRICAL TESTS
All units are factory tested in accordance with IEEE Standard 32-1972, specifically Sections 10.1.4 and 10.3.2. The
procedure includes a resistance measurement test to verify
that the tolerance is within + 10%, and an applied potential
test. A copy of the test report is included with each shipped
unit.
5713 13th Street
Katy, Texas 77493
Phone: (281) 391-6800, Fax: (281) 391-6810
Please visit our website at www.powerohm.com

Ratings & Dimensions of Standard Size Units

RATINGS: The following table contains information on the most
common size units, other variations are available.

10 SECOND TIME RATINGS

CATALOG
NUMBER

INITIAL
AMPS

RESISTANCE

1390 VOLTS LINE-TO-NEUTRAL (2400 VOLT SYSTEM)

13.90
NR1390-100-10
100
38
38
6.95
NR1390-200-10
200
38
38
4.63
NR1390-300-10
300
38
38
3.48
NR1390-400-10
400
38
38
2.78
NR1390-500-10
500
38
38
2.32
NR1390-600-10
600
38
38
1.74
NR1390-800-10
800
38
38
1.39
NR1390-1000-10
1000
38
38

APPROX.
WEIGHT

DIMENSIONS: The dimensions listed in the

table are in inches. Information subject to
change without notice.
FRONT VIEW
Neutral Bushing

30
30
30
30
30
30
30
30

280
290
300
310
320
340
350
360

30
30
30
30
30
30
36
36

380
390
400
410
420
430
490
500

Ground
Terminal

2400 VOLTS LINE-TO-NEUTRAL (4160 VOLT SYSTEM)

NR2400-100-10
NR2400-200-10
NR2400-300-10
NR2400-400-10
NR2400-500-10
NR2400-600-10
NR2400-800-10
NR2400-1000-10

100
200
300
400
500
600
800
1000

24.00
12.00
8.00
6.00
4.80
4.00
3.00
2.40

38
38
38
38
38
38
38
38

38
38
38
38
38
38
38
38

RIGHT SIDE VIEW

4160 VOLTS LINE-TO-NEUTRAL (7200 VOLT SYSTEM)

NR4160-100-10
NR4160-200-10
NR4160-300-10
NR4160-400-10
NR4160-500-10
NR4160-600-10
NR4160-800-10
NR4160-1000-10

100
200
300
400
500
600
800
1000

41.60
20.80
13.87
10.40
8.32
6.93
5.20
4.16

38
38
38
38
38
38
44
44

38
38
38
38
38
38
54
54

36
36
36
36
36
36
54
54

550
560
570
580
590
600
680
700

8000 VOLTS LINE-TO-NEUTRAL (13800 VOLT SYSTEM)

NR8000-100-10
NR8000-200-10
NR8000-300-10
NR8000-400-10
NR8000-500-10
NR8000-600-10
NR8000-800-10
NR8000-1000-10

100
200
300
400
500
600
800
1000

80.00
40.00
26.70
20.00
16.00
13.30
10.00
8.00

44
44
44
44
44
44
44
44

54
54
54
54
54
54
54
54

54
54
54
54
54
54
84
84

820
830
840
850
870
880
950
990

30
30
36

320
370
420

36
36
54

450
550
850

54
54
54

900
950
1400

EXTENDED TIME RATINGS

1390 VOLTS LINE-TO-NEUTRAL (2400 VOLT SYSTEM)
NR1390-15-E
NR1390-25-E
NR1390-50-E

15
25
50

92.7
55.6
27.8

38
38
38

38
38
38

2400 VOLTS LINE-TO-NEUTRAL (4160 VOLT SYSTEM)

NR2400-15-E
NR2400-25-E
NR2400-50-E

15
25
50

160.0
96.0
48.0

38
38
44

38
38
54

4160 VOLTS LINE-TO-NEUTRAL (7200 VOLT SYSTEM)

NR4160-15-E
NR4160-25-E
NR4160-50-E

15
25
50

227.3
166.4
83.2

44
44
84

54
54
54

The above drawing details a typical neutral

grounding resistor with enclosure. Units are
available with screened or louvered covers
on front and back. All units normally have
solid tops and sides and a perforated bottom.
TO ORDER A NEUTRAL GROUNDING RESISTOR NOT LISTED IN THE TABLE,
SPECIFY THE FOLLOWING:
1. Line-to-neutral voltage.
2. Initial fault current.
3. Maximum time on.
4. Special requirements or options.

Generator Neutral Grounding Resistors

APPLICATION

Generator Neutral Grounding Resistor

Powerohm offers high resistance grounding equipment for

wye connected generators. Our equipment is normally
designed to limit the line-to-ground fault current to below 15
amps for generators rated up to 14,400 volts. These units will
provide a high resistance neutral during a fault condition,
while allowing the system to operate as an ungrounded
system during normal operating conditions. The configuration basically consists of a dry-type single-phase transformer with a resistor connected across the secondary. The
primary of the transformer is then connected between the
wye point of the generator and ground.
Powerohm generator grounding equipment is normally supplied with the transformer and resistor installed in a common
enclosure. Continuous rated units are usually compartmentalized to separate the resistor assembly from the transformer which is subject to overheating. Units do not normally
include any relaying or control circuitry, but do offer the
transformer secondary wired to a terminal block installed in
an external junction box.
WYE-CONNECTED
GENERATOR
N
R

TO PROTECTIVE
RELAY

GROUNDING
TRANSFORMER
G

BASIC CONSTRUCTION
Transformer: For continuous time ratings, the transformer
must be capable of withstanding rated current for an indefinite period of time; therefore, the KVA rating of the grounding
transformer is equal to the rated line-to-neutral voltage times
the desired neutral current. For a short-time rating, the KVA
rating of a grounding transformer will be smaller because the
unit is designed to carry its rated current for a limited time.
Resistor Assembly: The resistance value is calculated by
dividing the secondary voltage by the rated current necessary to obtain the desired fault current on the primary.
Resistor elements are selected to best meet the current and
voltage requirements of the system. A typical assembly
includes all stainless steel elements, bus bars and
terminals.

Safety Enclosure: Our grounding assemblies are available

in grounded NEMA 1 or NEMA 3R safety enclosures,
complete with nearly any finish including mill galvanized,
power coated, hot dipped galvanized after fabrication, aluminum or stainless steel.
Options: A number of additional options are available,
including entrance bushings, current transformers, elevating stands, and disconnect switches.

ELECTRICAL TESTS
All units are factory tested in accordance with IEEE Standard 32-1972, specifically Sections 10.1.4 and 10.3.2. The
procedure includes a resistance measurement test to verify
that the tolerance is within + 10%, and an applied potential
test. A copy of the test report is included with each shipped
unit.

Resistance Grounding with a Zigzag Transformer

Zigzag Grounding Transformer with Resistor

APPLICATION
The best way to resistance ground a power system is to
obtain the system neutral through a generator or transformer with a wye-connected winding. However, a system
neutral may not be available, particularly in many older low
voltage systems and a significant number of existing
medium voltage systems. To avoid the high cost of replacing
a source transformer, an existing delta-connected system
can be grounded using a zigzag transformer to form an
artificial neutral, then connecting a resistor between the
newly created wye-point and ground.
A zigzag transformer has no secondary winding, and is
designed to provide a low-impedance path for the zerosequence currents to flow. During a line-to-ground fault
condition, the zero sequence currents can flow into the
ground at the point of the fault, and back through the neutral
of the grounding transformer. The impedance of the zigzag
transformer to balanced three-phase voltages is relatively
high, therefore, when there is no fault on the system, only a
small magnetizing current flows in the windings. A zigzag
grounding transformer provides a stable neutral point which
makes possible its use for grounding an otherwise isolated
neutral system.
A zigzag transformer with a resistance ground is normally
designed for a short time rating of 10 to 60 seconds.
Consequently, the grounding transformer is much smaller in
size than an ordinary continuously rated transformer with
the same rating. For short time ratings, the short time
temperature rise for the resistive element is 760C.

TO UNGROUNDED
3-PHASE VOLTAGE
SOURCE

TO UNGROUNDED
3-PHASE LOAD

ZIGZAG
TRANSFORMER

BASIC CONSTRUCTION
Transformer: For a short time rating, the grounding
transformer is designed to carry its rated current for a limited
time, consequently the unit is ordinarily much smaller,
physically, than an ordinary three-phase transformer for the
same rated kVA.
Resistor Assembly: The resistance value is calculated by
dividing the line-to-neutral voltage by the rated neutral
current. Resistor elements are selected to best meet the
short time current rating and voltage requirements of the
system. A typical assembly includes all stainless steel
elements, bus bars and terminals.
Safety Enclosure: Our grounding assemblies are available
in grounded NEMA 1 or NEMA 3R safety enclosures,
complete with nearly any finish, including mill galvanized,
power coated, hot dipped galvanized after fabrication, aluminum, or stainless steel.
Options: A number of additional options are available
including entrance bushings, current transformers, elevating stands and disconnect switches.

ELECTRICAL TESTS
R

RESISTOR

All units are factory tested in accordance with IEEE Standard 32-1972, specifically Sections 10.1.4 and 10.3.2. The
procedure includes a resistance measurement test to verify
that the tolerance is within + 10%, and an applied potential
test. A copy of the test report is included with each shipped
unit.

24 HOUR EMERGENCY SERVICE

(800) 838-4694