USER MANUAL T1.

TABLE OF CONTENTS

01
02
02
03
04
04
05
05
05
06
06
07
07
07
08
08
08
10
12
13
13

TABLE OF CONTENTS
INTRODUCTION
OVERVIEW
SPECIFICTATIONS
PLACEMENT BEFORE TAKEOFF
CHARGING
ASSEMBLY
POWERING ON / OFF
STARTING/STOPPING THE MOTORS
FLIGHT CONTROLS (SINGLE MODE)
- ST16 OVERVIEW
- FLYING
- LANDING
- PROPORTIONAL CONTROL RATE SLIDER
- FLIGHT MODES
- FOLLOW ME FUNCTION
- WATCH ME FUNCTION
- ADDITIONAL FUNCTIONS
FLIGHT CONTROLS (TEAM MODE)
TEAM MODE (ST12&ST16)
- BINDING THE ST12 AND THE COPTER

13
14
14
14
16
17
17
17
17
18
19
20
21
22
23
24
24
25
27
28

- BINDING THE ST16 AND THE CGO3+

- LANDING
- PROPORTIONAL CONTROL RATE SLIDER
- FLIGHT MODES
TEAM MODE (WIZARD&ST16)
-WIZARD LED STATUS
- BINDING THE ST16 AND THE CGO3+
- BINDING THE Typhoon WIZARD TO THE Typhoon H
- FLIGHT CONTROLS
- FLIGHT MODES
CAMERA CONTROLS
- TAKING PHOTOS AND RECORDING VIDEO
GPS FUNCTIONALITY / DISABLING GPS
COMPASS CALIBRATION
LED STATUS INDICATIONS
NOTICES AND WARNINGS
GENERAL SAFETY PRECAUTIONS AND WARNINGS
LIPO BATTERY WARNINGS AND USAGE GUIDELINES
DISCLAIMER
CERTIFICATION INFORMATION

INTRODUCTION
Typhoon H is an advanced aerial photography and videography platform, perfect for skilled pilots and photographers alike. It offers up to 25 minutes
of ight time while lming with the CGO3+ 4K-resolution camera. Settings can be freely and remotely adjusted through the ST16 Personal Ground
Station, an easy and intuitive remote controller which features a 7-inch Android touchscreen that displays live footage of your ight. To meet different
needs for function and portability, Typhoon H has two congurations: the professional version with Intel RealSense, equipped with a portable
backpack, and the advanced version with Sonar Collision Avoidance, which features an upgrade path to the professional version with the purchase of
a RealSense module, sold separately.

OVERVIEW

Power Switch
Sonar

Camera LED Status Indicator

CGO3+ Gimbal Camera

Camera Lens
5.8GHz Antenna

SPECIFICTATIONS
TYPHOON H SPECIFICATIONS
Flight Time

Up to 25 min

Maximum Rotation Rate

90/s

Takeoff Weight

69.3oz (1965g )

Maximum Climbing Speed

5m/s

Size

Battery

Battery Capacity/Voltage
Charger

Transmitter

Maximum Flying Height

20.5x17.9x11.6 in (520x456x296mm)

Maximum Roll Angle

4S 14.8V LiPo Battery (POWER 4)

Maximum Speed In Angle Mode

5400mAh 4S/14.8V79.9Wh

Maximum Descending Speed

SC4000-4

Diagonal Wheelbase

ST16 Personal Ground Station

Frame Arm Length

122m (400ft)(Restricted by FAA)

Landing Gear Size

45

13.5m/s
3m/s

18.9 in (480mm )
7.4 in (187mm)

10.4x7.3 in (265x185mm)

CGO3+CGO3 PLUS) SPECIFICATIONS

Weight

8.8oz (250g)

Electronic Shutter

Camera lens

14mm/F2.8 35mm

Transmission System

Effective Pixels
FOV

12.4 Megapixels

Video Transmission Range

98

Video UHD

4s1/8000s

Up to 1 Mile (1.6km)
5.2Ghz 5.8Ghz

4K 30FPS

ST16 GROUND STATION

Operating System:

Number of Channels:

Control Transmission Distance/Range:

Android

Video Transmission Distance/Range

Up to 1 Mile (1.6km) (Optimum Conditions)

LCD Screen Size:

16

FCC Compliance: Up to 1 Mile (1.6km)

(Optimum Conditions):

CE Compliance: Up to 1 Mile (1.6km)

Built-In Li-ion Battery Voltage / Capacity:

3.6V 8700mAh 31.32Wh Li-ion

Video Link Frequency Band:

5.8GHz WiFi

Operating System:

Android 4.0.3

Video Transmission Distance/Range

Control Transmission Distance/Range:

1000m

LCD Screen Size:

ST12 GROUND STATION

Number of Channels:

Video Link Frequency Band:

(Optimum Conditions):

12

Built-In Li-ion Battery Voltage / Capacity:

5.8GHz

FCC:up to 600m;

CE:up to 300m

5.5"

5200mAh 3.6V 18.72Wh Li-ion

WIZARD REMOTE CONTROLLER

Dimensions

Water Resistant

5.47 X 1.46 X 0.98 in (139 X 37 X 25 mm)

Working Hours

Yes

Built-In LiPo Battery Voltage / Capacity

3.5 h

3.7V 500mAh

PLACEMENT BEFORE TAKEOFF

CHARGING

WARNING: Always operate Typhoon H in open areas (approximately

10000 square feet/930 square meters or more) that are free from people,
vehicles, trees and other obstructions. Never y near or above crowds,
airports or buildings.

Power the SC4000-4 charger from a 100-240V AC outlet using the AC

adapter/power supply, or from a 12V-16.8V DC accessory socket/cigarette
lighter receptacle in a vehicle using the included adapter.
Plug the aircraft battery into the charger port as illustrated.
A green blinking LED indicates the charger is powered on and ready to
charge, and a red blinking LED indicates the battery is charging. It will take
approximately 2.5 hours to charge a fully discharged (not over-discharged)
battery. A solid green LED indicates the battery is fully charged.

power

Never attempt to operate Typhoon H nearby tall buildings/obstructions that

do not offer a clear view of the sky (a minimum clearance of 100).
Be sure to place Typhoon H on a level and stable surface before powering
ON the Ground Station and the aircraft.

WARNING: All instructions and warnings must be followed exactly to

prevent property damage and/or serious injury as the mishandling of
Li-ion/LiPo batteries can result in re.
FOR THE ST16 GROUND STATION
You can charge the ST16 battery by using supplied USB cable and inserting
it into the USB port on the charger. It will take approximately 5 hours to
charge a fully discharged (not over-discharged) battery.
WARNING: Do not leave the battery in the charger after the battery is fully
charged.

IMPORTENT NOTE: STEP BACK APPROXIMATELY 26 FEET (8 METERS)

BEHIND THE Typhoon H.

ASSEMBLY

STEP 4: REMOVE THE PROTECTIVE COVER AND INSERT THE SD CARD

Carefully remove the protective
cover from the camera lens.
Insert the included 16GB card or
any Class 10 microSD card from
16GB to 128GB.

STEP 1: ASSEMBLING THE ARMS

Unfold the motor arms and secure them until hearing a 'click'.
NOTICE: Press the 'PRESS' button
to fold the motor arms.

POWERING ON / OFF
NOTE: ALWAYS turn on the ST16 Ground Station and allow it to boot up
BEFORE turning Typhoon H on (and ALWAYS turn Typhoon H off BEFORE
turning off the ST16 Ground Station).

STEP 2: INSTALLING THE PROPELLERS

IMPORTANT NOTE: Always ensure propellers are installed properly. The motors are
extremely powerful, meaning that if the device is misused there is a risk of material
damage, serious injury and even fatal injury.
Mount the propellers on the motors and note the 'A' and 'B' given on the motor
arms. This distinction between 'A' and 'B' refers to propeller 'A' and 'B'. Mount
propeller 'A' on motor 'A' and propeller 'B' on motor 'B'press and rotate propellers in the direction the [
] points to, and the propellers will be locked.

POWERING ON ST16

POWERING ON Typhoon H

Place Typhoon H on a level and stable surface then power on the ST16 Ground
Station. Press and hold power button on Typhoon H. Release the button when the
aircraft emits a rising tune. DO NOT TOUCH OR MOVE THE Typhoon H UNTIL THE
INITIALIZATION PROCESS IS COMPLETE. The gimbal camera will spin to the front
position, the main aircraft LED will blink red, green and blue rapidly during the
process of initialization.
NOTICE: If the main LED blinks red slowly, the initialization has failed. The aircraft
needs to be powered on again. To power off the aircraft, press and hold the power
button until the aircraft emits a falling tune.

NOTICE: Press and hold the

center button on the propeller
and rotate the propeller in the
direction the [
] points to,
then you can disassemble the
propellers.

STARTING/STOPPING THE MOTORS

Step back approximately 26 feet (8 meters) behind Typhoon H.

Press and hold the START/STOP button for about 3 seconds to
start, and about 2 seconds to stop the motors.
Step back approximately 26 feet (8 meters) behind Typhoon H, make sure the ST16
Ground Station is in the Angle mode or Smart mode. When there is suitable GPS
signal for both the ST16 Ground Station and Typhoon H, you can start the motors.
To begin, tap the TASK/CAMERA icon on the ST16 screen, and tap the TAKE OFF
icon. Slide it on the screen, then the aircraft will climb to the height of 2 meters and
automatically hold its position (make sure both sticks are in the center position).

STEP 3: INSTALLING THE FLIGHT BATTERIES

Push the battery into the battery compartment with the Yuneec logo facing upwards
until hearing a 'click', which means the battery is installed successfully.

NOTICE: Gently open the battery cap to the maximum

degree (to a position where is almost horizontal with
the GPS cover), then you can pull the battery out.

GPS
VOL

FSK

12.6V

WiFi

FSK

CHA

WIFI

POS
CHA
POS

00 : 35

FLIGHT CONTROLS (SINGLE MODE)

08

01
02
03
04
05

09

06

12

07

13

10
11

14

15

16

17

18

19

ST16 OVERVIEW
01
02 Gimbal Pan Mode (Follow Mode/Follow Pan
Controllable Mode/Global Mode)
03 Gimbal Tilt Mode (Angle Mode/ Velocity Mode)
04 Gimbal Pan Control
05 Rudder/Yaw Control (Mode 2 and Mode 1)
06 Throttle/Altitude Control ( Mode 2)
Elevator/pitch control (Mode 1)
07 Take Still Photo Button
08 Landing Gear Switch
09 Sonar Obstacle Avoidance Switch
10 Flight Mode Selection Switch
11 Aileron/Roll Control (Mode 2 and Mode 1)
12 Elevator/Pitch Control (Mode 2)
13 Throttle/Altitude Control (Mode 1)
Start/Stop Video Recording Button
14 Power Switch
15 Mushroom Antenna
16 Antenna
17 Proportional Control Rate Slider
18 Gimbal Tilt Control Slider
19 Battery

LANDING - There are two ways to land Typhoon H:

1) Position Typhoon H above the area where you would like to land. Slowly lower
the left-hand stick to below the center position. Typhoon H will descend slowly and
land. After Typhoon H lands, press and hold the START/STOP button until the
motor stops.
2) Activate Home Mode and Typhoon H will automatically y itself back to the
home point and land.
NOTICE: After the copter takes off, the pilot can
retract the landing gear by switching up the
Landing Gear Switch on the top right side of the
ST16 Ground Station. Make sure to ip the switch
to the downward position when landing.
WARNING: Always land as soon as possible after
the rst low level voltage battery warning, or land
immediately after the second level low voltage
battery warning (as indicated by the vibrations
and audible alerts from the ST16 Ground Station,
and by the Motor LED Status Indicators ashing
rapidly). If at any time the Aircraft Battery Voltage
shown on the screen is below 14.1V, land Typhoon
H immediately.

CLIMB MAX ALTITUDE

400 FEET / 122 METERS
MAINTAIN ALTITUDE
DESCEND / LAND

To take off, slowly raise the left-hand stick to above the center position. Typhoon H
will take off and climb slowly (or raise the stick further until it does). Allow the stick
to return to the center position when Typhoon H reaches the desired altitude.

GPS

TS01

VOL

FSK

12.6V

WiFi

FSK

CHA

WIFI

300M

TS02

TS03

125km/h

Roll 120

Pitch 0

FLYING

TS06

CHA

TS07

D/R 0

POS

00 : 35 : 25

Take your time learning how Typhoon H responds to various control inputs while
ying. In Smart Mode, Typhoon H will always move in the direction the right-hand
control stick is pushed relative to the pilot and no matter which way the front/nose
is pointed.
In Angle (Pilot) Mode, Typhoon H will move in the direction the control stick is
pushed relative to the front/nose of the aircraft (and the angle of movement is
determined by how far you push the stick away from the center position). Please see
the corresponding sections of this instruction manual for more information on
Smart Mode and Angle (Pilot) Mode.

TS04

TS05

POS

System Setting

TS08

Channel Setting

Model Select

AFTER LANDING
ALWAYS turn off Typhoon H BEFORE turning off the ST16 Ground Station. Then
remove the battery from Typhoon H and allow it to cool to ambient/room temperature before recharging.
NOTICE: If the signal of the remote control is lost, Typhoon H will automatically
return to the home point and hold its position (with a suitable GPS signal/lock) over
the home position (except for low battery).
PROPORTIONAL CONTROL RATE SLIDER
The Proportional Control Rate Slider located on the right side of the ST16 Ground
Station allows you to set the overall climb/descend and directional control rates.
Use the turtle position for the lowest control rates (best for rst-time pilots and
required when ying between 5000 feet and 8000 feet Above
Mean Sea Level), and use the rabbit position for the highest
control rates (best for experienced pilots and can only be used
when ying below 5000 feet MSL). Or use a position in
between if you prefer.

IMPORTANT NOTE: If at any time during ight you

feel like Typhoon H is drifting out of/beyond your
control, simply release both control sticks. Typhoon H
will automatically self-level and will even hold its
position (with a suitable GPS signal/lock) when both
control sticks are centered. You can also activate
Home Mode so Typhoon H automatically ies itself
back to the home point and lands.

FLIGHT MODES
The ST16 Ground Station is equipped with 3
different ight modes which can be selected
by using the mode switch in the top right
corner above the right joystick.
GPS

TS01

VOL

FSK

12.6V

- SMART
- ANGLE
- HOME

300M

FOLLOW ME FUNCTION

TS02

SMART MODE
FSK

CHA

WIFI

125km/h

Roll 120

Pitch 0

TS04

TS05
TS06

POS

TS07

CHA

D/R 0

POS

00 : 35 : 25

System Setting

TS08

Channel Setting

Model Select

*ADDITIONAL SMART MODE FEATURES

FOLLOW ME
The Follow Me function allows Typhoon H to
follow the pilot, adjusting its location to the
location of the ST16 Ground Station. This
function is enabled when ST16s GPS
positioning completes, and Typhoon H is
using shared GPS signal with the ST16
Ground Station. When Follow Me is activated,
the background of the 'Follow' character will
be red and the icon of Follow [ ] will be
highlighted in white. Typhoon H will follow
the movement of ST16 Ground Station if
there is no extra operation on the ST16
Ground Station. The ight status is also controllable when you operate the ST16 and CGO3+.
IMPORTANT NOTE: In Follow Me, the aircraft
will maintain a constant altitude and cannot
detect obstacles. Pilots who change their
altitude during ight should be mindful of
this.

WATCH ME FUNCTION

WATCH ME
Watch Me enables the camera to keep tracking the remote controller no matter
where and how it moves as the camera can automatically tilt its angle according
to the controller. Usually, the default function under Smart Mode is Follow Me.
Watch Me function can be switched to by following steps:
In Watch Me, the pilot will always be kept in the frame wherever they move.
Watch Me/Follow Me Button: When in Smart Mode, press [
] to switch
Typhoon H between the Watch Me and Follow Me function. The Follow Me
function is the default setting, and the icon [
] of Follow will be highlighted
white and the background of Follow character will turn red. If it is NOT
AVAILABLE, it means the ST16s GPS isnt ready yet. Please wait.
Press [
] ,and the background of the 'Watch' character will turn red and the icon of
Watch [ ] will be highlighted white. The Follow [
] will turn grey and the background
of the Follow character will turn black. This means the Watch Me function is now enabled.

TS03

When the Flight Mode selection switch is in the top position Typhoon H will be
in Smart Mode. Although we recommend learning to y Typhoon H in Angle
(Pilot) Mode as soon as possible, Smart Mode is typically the best mode for
beginning pilots to y in and also features 'Follow Me'.
In Smart Mode Typhoon H will always move in the direction the right-hand
control stick is pushed relative to the pilot and no matter which way the
front/nose is pointed. So if you push the stick to the left, Typhoon H will always
move to the left, regardless of the direction the nose is pointing and even if its
spinning. This mode can also be helpful for pilots that lose orientation while
ying in Angle (Pilot) Mode.
WiFi

SMART CIRCLE
In most cases the Smart Circle will keep Typhoon H from coming within approximately 26 feet (8 meters) of you (as long as you position yourself at least 26
feet/8 meters behind Typhoon H.
GEO-FENCE
The geo-fence is a virtual barrier that will keep Typhoon H from traveling farther
than 300 feet (91 meters). The geo-fence only works in Smart Mode. Although
this limit can be adjusted using the USB interface/programmer and software we
strongly recommend using the default limit at all times.
WARNING: Smart Mode only works when Typhoon H has a suitable GPS
signal/lock. If you take off in Smart Mode and Typhoon H loses GPS signal/lock
it will switch to Angle (Pilot) Mode automatically. This is why we strongly recommend learning to y in Angle (Pilot) Mode as soon as possible. Otherwise, if you
lose GPS signal/lock and are not able to properly control Typhoon H in Angle
(Pilot) Mode the aircraft may crash or even y away.
IMPORTANT NOTE: Crash damage and y aways are NOT covered under warranty.
IMPORTANT NOTE: When the ST16 Ground Station is connected to less than 6
satellites, the FOLLOW ME feature will be disabled.

SMART CIRCLE

Mode 2 shown

ANGLE MODE
When the Flight Mode selection switch is the middle position, Typhoon H will be
in Angle Mode, also known as Angle (Pilot) Mode.
Angle (Pilot) Mode is the mode preferred by experienced RC/drone pilots
because Typhoon H will move in the direction the control stick is pushed relative
to the front/nose of the aircraft. So if you push the right-hand stick to the left
Typhoon H will bank toward the left side and move to the left. This means if the
front/nose of Typhoon H is pointing away from you it will move to the left, but if
the front/nose is pointing at you
Typhoon H will move to the right.
*Additional Angle (Pilot) Mode Feature:
The Typhoon H will automatically hold
its position (with a suitable GPS
signal/lock) and maintain a level attitude
Mode 2 shown
when the both joysticks are centered.
WARNING: If you do not properly
control Typhoon H in Angle (Pilot) Mode the aircraft may crash or even y away.
IMPORTANT NOTE: Crash damage and y aways are NOT covered under warranty.
OBSTACLE AVOID Switch
With sustainable GPS locked, the sonar can be activated in Angle (Pilot) Mode
by being switched on with Typhoon H higher than 9.9ft (3 meters). When the
sonar is activated, the front motor LED will blink white and the icon on the ST16
screen will be solid green. If the OBSTACLE AVOID is switched on, but the function
can't be activated, then the icon will be yellow.
IMPORTANT NOTE: The environment requirement such as ying height might
change depending on the situation. Only when the icon on the ST16 screen is
solid green, it means the OBSTACLE AVOID function is activated.
NOTICE: The sonar can only detect the front obstacles, but can't detect the lateral and rear
obstacles.
NOTICE: The speed of the aircraft will be limited with Sonar activated.
NOTICE: For the most up-to-date information of OBSTACLE AVOID, please visit the
corresponding product page at www.Yuneec.com or contact the nearest Yuneec ofce or
authorized distributor.

(4-8m) of the pilot. This can be very helpful for

beginning pilots who arent quite ready to land
Typhoon H themselves. It can also be helpful for
pilots that lose orientation during ight. Simply
activate Home Mode until Typhoon H automatically
moves toward the home position, and once youve
conrmed orientation switch back to Angle (Pilot)
Mode. If Typhoon H ever loses the link with the ST16
Ground Station it will automatically enter Home
Mode.
NOTICE: If the signal of remote control is lost,
Typhoon H will automatically return to home point
and hold its position (with a suitable GPS signal/lock)
over the home position except for low battery.

LANDING
LOCATION

(4-8m)
PILOT LOCATION

WHEN HOME MODE IS ACTIVATED Typhoon WILL RESPOND AS FOLLOWS:

A) When ying higher than 33 feet (10 meters) Typhoon H will maintain the
current altitude, y back to the home point, or active home point if the ST16
Ground Station has enough satellites for Follow Me, then descend vertically
until it lands.
B) When ying lower than 33 feet (10 meters) Typhoon H will climb to 33 feet
(10 meters) while ying back to the home point, or active home position, then
will descend vertically until it lands.

A
10 m

10 m

NOTICE: Users can control pitch, roll and yaw directions during descent. The Typhoon
H will hang over the home position at the current height when RC signal is lost.
CAUTION: You must be certain there are no obstacles in the Return to Home ight path
otherwise Typhoon H may come into contact with them and crash. While
Typhoon H is in Home Mode you will have a limited amount of directional
control. To help avoid obstacles we strongly recommend to switch to Smart or
Angle Mode (then you can switch back to Home Mode).
WARNING: Home Mode only works when Typhoon H has a suitable GPS
signal/lock. If Typhoon loses GPS signal/lock it will switch to Angle (Pilot) Mode
automatically. This is why we strongly recommend learning to y in Angle (Pilot)
Mode as soon as possible. Otherwise, if you lose GPS signal/lock and are not
able to properly control Typhoon H in Angle (Pilot) Mode the aircraft may crash
or even y away.

HOME MODE
When the Flight Mode selection switch is in the bottom position Typhoon H will be
in Home (also known as Return to Home) Mode.
In Home Mode the GPS connectivity will y back Typhoon H in a straight line in the
direction of the pilots current location, and automatically land within 13-26 ft

Tap the CCC to enter the Curve Cable Cam function.

ADDITIONAL FUNCTIONS:
SONAR OBSTACLE AVOIDANCE

BACK

With sustainable GPS locked, the sonar can be activated in

Angle (Pilot) Mode by being switched on with Typhoon H
higher than 9.9ft (3 meters). When Sonar is activated, the front
motor LED will blink white and the icon on the ST16 screen
will be solid green. If the OBSTACLE AVOID is switched on,
but the function can't be activated, then the icon will be
yellow.
Tap the System Settings and choose Other Settings on the ST16 Ground Station,
turn on the Advance Mode, and tap [
]. After, tap the TASK/CAMERA
icon, the background of 'TASK' will become orange, then you will enter another
interface displaying four functions: CCC (Curve Cable Cam), Journey, POI (Point of
Interest) and ORBIT ME functions.
GPS

TS01

VOL

FSK

12.6V

WiFi

FSK

CHA

WIFI

300M

TS02

TS03

125km/h

Roll 120

TS04

Pitch 0

TS05

POS

00 : 35 : 25

System Setting

Model: Typhoon H

Channel Setting

GPS

welcome,Pilot

INSTRUCTION
RESET: Delete all waypoints

POS

+/-: Add/Delete a waypoint

N/AV

LIST: Load existing waypoint

ALT

START: Press START, and Typhoon H will up and out and then take a sele.
BACK: Tap BACK to return to the previous interface.

Disabled

SLIDE TO START

SAVE: Save waypoint

START: Start waypoint mission

GPS
CALIBRATION

CANCEL

G-SPD

FOLLOW
WATCH

N/A KPH

BACK

DIS

RESET

LIST

SAVE

START

1/3
TASK
CAMERA

N/Am

Pad

Tap JOUR to enter the journey function.

OBS

Make sure the H is clear of all

obstacles before starting mission.

JOUR: Journey function enables Typhoon H to capture the perfect aerial

sele much easier. Depending on the pilot's desired setting, Typhoon H
will go up, out and return.

ANGLE

SAT

12
G

N/AE
N/AN

N/Am

12:27 AM

PONINT 3

N/A

Model Select

CCC
PONINT 2

START

TS08

CCC: (Curve Cable Cam) Curve Cable Cam allows you to create an
invisible route for Typhoon H to y along. Once the pilot sets the point,
Typhoon H will y the set coordinates while remembering the heading.

PONINT 1

SAVE

BACK: Tap BACK and you can return to the previous interface.
RESET: Tap RESET to delete all the points created during the ight.
: Tap '-' to delete the last point created during the ight.
: Tap '+' to create a new point recording the current ying position.
LIST: Tap LIST and all previous routs will be shown on a list. You can delete any of
them by sliding the chosen one to the left.
SAVE: Tap SAVE and the current route will be saved.
START: Tap START, and Typhoon H will y along the route newly created.

TS07

D/R 0

POS

N/A

LIST

TS06

CHA

VOLTS

RESET

Model Select

10

POI: Point of Interest allows the pilot to select a subject they would like
to orbit and have Typhoon H orbit that subject autonomously.

ORBIT ME: When Orbit Me is enabled, Typhoon H ies a circular path

around the pilot.
Press ORBIT to enter the ORBIT ME function.
START: Press START, and then Typhoon H will y around the pilot with the distance
between the start point and the pilot as the radius.
BACK: Tap BACK to return to the previous interface.

CENTER: Press CENTER to set the current ight position of Typhoon H as the center of a circle.

START: Press START, and Typhoon H will y around the circle center with distance
between the Start point and the center point as the radius.
BACK: Tap BACK to return to the previous interface.

11

FLIGHT CONTROLS (TEAM MODE)

12

01
02
03

05
06
07
08

04

09
10

11

13
15

14
16

24

25
26
27

17
18

19

30

20

21

28

31

29

32

22

23

PILOT (ST12)

01
02
03
04
05
06
07
08
09
10

Landing Gear Switch

Rudder/Yaw Control (for Mode 2 and Mode 1)
Elevator/Pitch Control (for Mode 1)
GPS Knob
Aileron/Roll Control (for Mode 2 and Mode 1)
Elevator/Pitch Control (for Mode 2)
Power Switch

CAMERA OPERATOR (ST16)

PILOT (WIZARD)

11
12
13
14
15
16
17
18
19
20
21
22
23
24

Wizard GPS LED

25

26
27
28
29
30
Wizard Power LED
Smart / Angle / Home Mode Switch

12

31
32

Pan Mode
- Follow (yaw cant be controlled)
- Follow Controllable
- Global
Gimbal Tilt Slider in Angle
Tilt Mode:
-Angle
-Velocity
Gimbal Tilt Control in Velocity Mode (Mode 1)
Gimbal Pan Control in Global
Follow Controllable mode
Tilt Control in Velocity (mode 2)
Start/Stop Video Recording Button

TEAM MODE (ST12&ST16)

CLIMB MAX ALTITUDE
400 FEET / 122 METERS

BINDING THE ST12 AND THE COPTER

STEP 1) Turn on Typhoon H, and after the
Main LED Status Indicator begins to ash
blue rapidly, lift the back end upward
approximately 45 then back down to
'level' two times to put the aircraft/receiver into binding mode. The Main LED
Status Indicator will begin to ash orange
very rapidly when the aircraft/receiver are
in bind mode.
STEP 2) Turn on the ST12, and if required tap the screen (outside of the pop up
status window) to bypass the RC and WiFi connection process.
STEP 3) Tap the 'Model Select' button, and if required press 'OK' to bypass any pop
up warnings/alerts.
STEP 4) Select the existing model you would like to bind to (for example: 'Typhoon'
) or create a 'New Model', and if required press OK to bypass any pop up
warnings/alerts.
STEP 5) Tap the 'Flight Settings' button, and if required press 'OK' to bypass any
pop up warnings/alerts.
STEP 6) Tap the 'Bind' button and select the 'SR24_XXXXX' receiver listed in the
column under 'Model', then tap 'OK' after the connection has been established.
STEP 7) Tap the 'Back' button two times to return to the main screen and the
model/receiver should automatically connect to the ST12.
BINDING THE ST16 AND THE CGO3+
STEP 1) Switch on Typhoon H rst, and then power on the ST16 Ground Station.
STEP 2) Enter the "FPV" mode, press the 'Model Select' on the ST16 Ground Station
screen, and press "OK" when you see the window pops up.
STEP 3) Choose the CGO3+ model and then tap 'OK'.
STEP 4) Tap the 'System Settings' on the screen and choose the corresponding
MAC number of the CGO3+ Gimbal Camera, then tap 'bind'.
STEP 5) Insert the password '1234567890' as requested, and tap 'OK'.
STEP 6) Tap the 'BACK (icon)' on the lower right corner, and you will go back to the
previous interface.

MAINTAIN ALTITUDE
DESCEND / LAND

To take off, slowly raise the left-hand stick to above the center position. The
Typhoon H will take off and climb slowly (or raise the stick further until it does).
Allow the stick to return to the center position when Typhoon H reaches the desired
altitude.
FLYING
Take your time learning how Typhoon H responds to various control inputs while
ying. In Smart Mode, Typhoon H will always move in the direction the right-hand
control stick is pushed relative to the pilot and no matter which way the front/nose
is pointed.
In Angle (Pilot) Mode, Typhoon H will move in the direction the control stick is
pushed relative to the front/nose of the aircraft (and the angle of movement is
determined by how far you push the stick away from the center position). And
please see the corresponding sections of this instruction manual for more information on Smart Mode and Angle (Pilot) Mode.
IMPORTANT NOTE: If at any time during ight you
feel like Typhoon H is drifting out of/beyond your
control, simply release both control sticks. The
Typhoon H will automatically self-level and will even
hold its position (with a suitable GPS signal/lock)
when both control sticks are centered. You can also
activate Home Mode so Typhoon H automatically ies
itself back to the home point and lands.

13

LANDING
There are two ways to land Typhoon H:
1) Position Typhoon H above the area where you would like to land. Slowly lower
the left-hand stick to below the center position. Typhoon H will descend slowly and
land. After Typhoon H lands, press and hold the START/STOP button until the
motor stops.
2) Activate Home Mode and Typhoon H will automatically y itself back to the home point and land.
NOTICE: After the copter takes off, the pilot can retract
the landing gear by switching up the Landing Gear
Switch on the top right side of the ST12 Ground
Station. Make sure to ip the switch to the downward
position when landing.
WARNING: Always land as soon as possible after the
rst low level voltage battery warning, or land immediately after the second level low voltage battery
warning (as indicated by the vibrations and audible
alerts from the ST12 Ground Station, and by the Motor
LED Status Indicators ashing rapidly). If at any time
the Aircraft Battery Voltage shown on the screen is
below 14.1V, land Typhoon H immediately.
AFTER LANDING
ALWAYS turn off Typhoon H BEFORE turning off the ST12 Ground Station. Then
remove the battery from Typhoon H and allow it to cool to ambient/room temperature before recharging.
NOTICE: If the signal of the remote control is lost, Typhoon H will automatically
return to the home point and hold its position (with a suitable GPS signal/lock) over
the home position (except for low battery).
PROPORTIONAL CONTROL RATE SLIDER
The Proportional Control Rate Slider located on the right side of the ST12 Ground
Station allows you to set the overall climb/descend and directional control rates.
Use the turtle position for the lowest control rates (best for rst-time pilots and
required when ying between 5000 feet and
8000 feet Above Mean Sea Level), and use the
rabbit position for the highest control rates
(best for experienced pilots and can only be
used when ying below 5000 feet MSL). Or
use a position in between if you prefer.

FLIGHT MODES
The ST12 Ground Station is equipped with 3
different ight modes which can be selected
by using the mode switch in the top right
corner above the right joystick.

SMART MODE
When the Flight Mode selection switch is in the top position Typhoon H will be
in Smart Mode. Although we recommend learning to y Typhoon H in Angle
(Pilot) Mode as soon as possible, Smart Mode is typically the best mode for
beginning pilots to y in and also features 'Follow Me'.
In Smart Mode Typhoon H will always move in the direction the right-hand
control stick is pushed relative to the pilot and no matter which way the
front/nose is pointed. So if you push the stick to the left Typhoon H will always
move to the left, regardless of the direction the nose is pointing and even if its
spinning. This mode can also be helpful for pilots that lose orientation while
ying in Angle (Pilot) Mode.
*ADDITIONAL SMART MODE FEATURES

FOLLOW ME FUNCTION
The Follow Me function allows Typhoon H to follow the pilot, adjusting its
location to the location of the ST12 Ground Station. This function is enabled
when ST12 GPS positioning completes, and Typhoon H is using shared GPS
signal with the ST12 Ground Station. At this time, you will see [ ] in orange, and
[
] in green color.
MODE

Follow

When in Follow Me, Typhoon H will follow the movement of ST12 Ground Station
if there is no extra operation on the ST12 Ground Station. The ight status is also
controllable when you operate ST12 Ground Station and CGO3+ gimbal
camera.
SMART CIRCLE

Mode 2 shown

14

(Pilot) Mode the aircraft may crash or even y away.

IMPORTANT NOTE: Crash damage and 'y aways' are NOT covered under warranty.
HOME MODE
FOLLOW ME FUNCTION

When the Flight Mode selection switch is in the bottom position Typhoon H will
be in Home Mode, also known as Return to Home Mode.
In Home Mode the GPS connectivity will y Typhoon H back in a straight line in the

WATCH ME FUNCTION

WATCH ME FUNCTION

direction of the pilots current location, and

automatically land within 13-26 ft (4-8m) of the
pilot. This can be very helpful for beginning
pilots who arent quite ready to land Typhoon H
themselves. It can also be helpful for pilots that
lose orientation during ight. Simply activate
Home Mode until Typhoon H automatically
moves toward the home position, and once youve
conrmed orientation switch back to Angle (Pilot)
Mode. If Typhoon H ever loses the link with the
ST16 Ground Station it will automatically enter
Home Mode.
NOTICE: If the signal of remote control is lost,
Typhoon H will automatically return to home
point and hold its position (with a suitable GPS
signal/lock) over the home position except for
low battery.

Watch Me enables the camera to keep tracking the remote controller no matter
where and how it moves as the camera can automatically tilt its angle according
to the controller.
Usually, the default function under Smart Mode is Follow Me. Watch Me
function can be switched on by following these steps:
Watch Me/Follow Me Button: When in Smart Mode, press [
] to switch
Typhoon H between Watch Me and Follow me function. Follow Me function is
the default setting, and the button is ORANGE. If it is GREY, it means ST12 GPS
isn't ready yet. Please wait.
Press [
] , and the button will change from ORANGE to GREEN. A green
symbol indicates that you are in Watch Me.
NOTICE: Once Typhoon H is above 2m and out of Smart Circle during ying,
Typhoon H yaw direction will take the control itself. The camera lens will always
point to you as long as the Flight Mode Selection Switch is in Smart Mode.
Please put the CGO3+ Pitch Angle/Position Control Slider in the middle
position. If you want to trim the camera angle up, then just move the Pitch
Angle/Position Control Slider a bit up. If you want to trim
the camera angle down, just move the slider down.

LANDING
LOCATION

(4-8m)
PILOT LOCATION

WHEN HOME MODE IS ACTIVATED Typhoon WILL RESPOND AS FOLLOWS:

Additional Smart Mode Features:

*SMART CIRCLE
In most cases the Smart Circle will keep Typhoon H from coming within approximately 26 feet (8 meters) of you as long as you position yourself at least 26
feet/8 meters behind Typhoon H.
GEO-FENCE
The geo-fence is a virtual barrier that will keep Typhoon H from traveling
further than 300 feet (91 meters). Although this limit can be adjusted using the
USB interface/programmer and software we strongly recommend using the
default limit at all times.
WARNING: Smart Mode only works when Typhoon H has a suitable GPS
signal/lock. If you take off in Smart Mode and Typhoon H loses GPS signal/lock
it will switch to Angle (Pilot) Mode automatically. This is why we strongly recommend learning to y in Angle (Pilot) Mode as soon as possible. Otherwise, if you
lose GPS signal/lock and are not able to properly control Typhoon H in Angle

A) When ying higher than 33 feet (10 meters) Typhoon H will maintain the
current altitude, y back to the home point, or active home point if the ST16
Ground Station has enough satellites for Follow Me, then descend vertically
until it lands.

A
10 m

10 m

B) When ying lower than 33 feet (10 meters) Typhoon H will climb to 33 feet
(10 meters) while ying back to the home point, or active home position, then
will descend vertically until it lands.

15

NOTICE: Users can control pitch, roll and yaw directions during descent. The Typhoon H
will hang over the home position at the current height when RC signal is lost.
CAUTION: You must be certain there are no obstacles in the Return to Home ight path
otherwise Typhoon H may come into contact with them and crash. While
Typhoon H is in Home Mode you will have a limited amount of directional
control. To help avoid obstacles we strongly recommend to switch to Smart or
Angle Mode (then you can switch back to Home Mode).
WARNING: Home Mode only works when Typhoon H has a suitable GPS
signal/lock. If Typhoon H loses GPS signal/lock it will switch to Angle (Pilot)
Mode automatically. This is why we strongly recommend learning to y in Angle
(Pilot) Mode as soon as possible. Otherwise, if you lose GPS signal/lock and are
not able to properly control Typhoon H in Angle (Pilot) Mode the aircraft may
crash or even y away.
IMPORTANT NOTE: Crash damage and 'y aways' are NOT covered under warranty.

TEAM MODE (WIZARD&ST16)

BINDING THE ST16 AND THE CGO3+
STEP 1) Switch on Typhoon H rst, and then power on the ST16 Ground Station.
STEP 2) Press the 'Model Select' on the ST16 Ground Station screen, and press "OK"
when you see the window pops up.
STEP 3) Choose the CGO3plus model and then tap 'OK'.
STEP 4) Tap the 'System Settings' on the screen and choose the corresponding
MAC number of the CGO3+ Gimbal Camera, then tap 'bind'.
STEP 5) Insert the password '1234567890' as requested, and tap 'OK'.
STEP 6) Tap the [ ] on the lower right corner, and you will go back to the previous interface.
BINDING THE TYPHOON WIZARD TO TYPHOON H
STEP 7) Switch off Typhoon H, and then switch on it again. Do not touch it until the
initialization completes.
STEP 8) Lift its tail upwards approximately 45 then back down to 'level' twice to put
the aircraft/receiver into binding mode.
STEP 9) Press and hold the Power Button till the Aircraft Mode LED glows solid blue.
Do not release the Power Button till hearing two beeps from the aircraft. Then
release it.
STEP 10) After the binding for Typhoon H completes, You can use the Typhoon
Wizard to y Typhoon H copter, and the ST16 Ground Station to control the
CGO3+ Gimbal Camera.
NOTICEWhen the binding completes under the Team Mode, you
can choose Typhoon H model to rebind the copter under the single
mode. The detailed information can be referred to the relevant
chapter in the User Manual.

16

WIZARD LED STATUS:

RETRACTING THE LANDING GEAR

After the copter takes off, the pilot can retract the landing gear by pressing the two
buttons [
]at the same time. Make sure to press the two buttons at the same
time again when landing.
WARNING: Always land as soon as possible
after the rst low level voltage battery
warning, or land immediately after the
second level low voltage battery warning (as
indicated by the vibrations and audible alerts
from the ST12 Ground Station, and by the
Motor LED Status Indicators ashing rapidly).
If at any time the Aircraft Battery Voltage
shown on the screen is below 14.1V, land
Typhoon H immediately.

Aircraft Mode LED

Smart Mode: LED solid green
Watch Me Function: LED solid green
Follow Me Function: LED solid yellow
Angle Mode: LED solid purple
Home Mode: LED solid red
Point To Fly Function Activated: LED solid blue
Wizard GPS LED
GPS Locked: LED solid green.
Aircraft Status LED

FLIGHT CONTROLS

The Communication Mal-function Between the Wizard and the Aircraft : LED solid red
GPS Loss of Aircraft: LED off
Aircraft in No-Fly Zone: LED blinking red, green and blue alternately
Battery fullLED solid green
Battery 50%LED blinking green twice every 2 seconds
Battery 25%LED blinking green once every 2 seconds
Low Voltage Warning of the Aircraft:
LED blinking red quickly, the Wizard vibrating for 2 seconds once continuously

NOTICE: The safe distance between the Typhoon Wizard and the aircraft is
39 ft (12m). The Typhoon Wizard can be controlled in different positions. Direction
Control Buttons function differently according to the positions of the Wizard.
1) When the Typhoon
Wizard is tilted upward
between 50 and 90, the
functions of the Direction
Control Buttons are as
followed:

Wizard Power LED:

Powered On: LED solid green
During Charging: LED solid red
Charging Completed: Red LED off
Low Voltage Warning of the Wizard:
Low Battery--- LED blinking green twice every 2 seconds
Low Voltage--- LED blinking green once every 2 seconds
Power Cut-off---LED blinking red quickly, the Wizard vibrating for 2
seconds once continuously.

90
50

2) When the Typhoon

Wizard is tilted upward
between 0 and 40, the
functions of the Direction
Control Buttons are as
followed:

40

Fly Forward

Ascend

Turn Right

Descend

90

Fly to the

Fly to the

Fly Backward

NOTICE: When the aircraft ies to the left or right side, the nose of aircraft doesn't change
its direction when the Typhoon Wizard is tilted upwards between 0 and 40.

17

POINT TO FLY FUNCTION

Press and hold the Magic Button on the Typhoon Wizard, and the aircraft will y in the
direction the Typhoon Wizard is pointed to in the sky.
To Enter Point To Fly Function
When the aircraft is ying, point the Typhoon Wizard to a direction, press and hold the Magic
Button. Release the Magic Button when Aircraft Mode LED glows solid blue and Typhoon
Wizard vibrates once. Then the aircraft will y to the direction the Typhoon Wizard points.
The closer the Typhoon Wizard is tilted towards 0, the further the aircraft will y away from the pilot.
The closer the Typhoon Wizard is tilted towards 90, the closer the aircraft will y to the pilot.
When the Wizard is tilted at 90, the aircraft will y close to you
straightly and stop at a safe distance.
NOTICE: The recommended ying height is 33-66 ft
(10-20 m). The operating distance range of the Typhoon
Wizard is 33-164 ft (10-50 m).

2) Follow Me Function Under Smart Mode

The Follow Me function allows the aircraft to follow the pilot, adjusting its location to the
location of the Typhoon Wizard. All buttons are controllable in this mode. When in
Follow Me, the aircraft will follow the movement of the Typhoon Wizard if there is no extra
operation on the Typhoon Wizard.
Follow Me function can be switched to
by the following steps:
When in Smart Mode, press the Magic
Button quickly once, it is "follow me"
model if Aircraft Mode LED is yellow and
Wizard GPS LED is green.

To Exit Point To Fly Function

When in the Point To Fly Function, press any Direction
Control Button to exit this function. The aircraft will stop
moving and automatically hold its position (with a suitable
GPS signal/lock) and maintain a level attitude then.

ANGLE MODE
When the Flight Mode Selection Switch is in the middle position, the aircraft will be in
Angle Mode. When Angle Mde is enabled, the Aircraft Mode LED will glow solid purple.
In this mode, the aircraft will move in the direction the Typhoon Wizard is controlled relative
to the front/nose of the aircraft. The aircraft has no function of Follow Me or Watch Me.
NOTICE: In this mode, the Point To Fly Function can't be activated.
IMPORTANT NOTICE: In Angle Mode, it is not suggested travelling further than 656 ft
(200 m). The Wizard will keep vibrating when the aircraft travels further than 656 ft (200
m).

WARNING: The maximun ight speed of the Typhoon H aircraft is 3.14MPH (7m/s).
If the movement of the pilot is much faster than 3.14MPH (7m/s), the aircraft may
y away.

Smart Circle

FLIGHT MODES

SMART MODE
When the Flight Mode Selection Switch is in the top position, the aircraft will be in the Smart
Mode. The Aircraft Mode LED will glow solid green.
1) Watch Me Function Under Smart Mode
Watch Me function enables the camera to keep
tracking the Typhoon Wizard no matter where
and how it moves as the camera can automatically tilt its angle according to the controller. It is
"watch me" mode if both the LEDs for Aircraft
Mode and Wizard GPS are green.
Usually, the default function under the Smart
Mode is Watch Me.
The Turn Left and Turn Right are disabled in this mode (Fly to the Left Direction and Fly
to the Right Direction can be controlled). The pilot will always be kept in the frame wherever he/she moves.
NOTICE: In the Smart Mode, the geo-fence will keep the aircraft from traveling further than
295 ft (90 m). The geo-fence is a virtual 'barrier'.
CAUTION: Any operation related to camera control needs to be done on mobile APPs. The
APP can be downloaded from Google Play Store or APP Store. You cant use the Wizard
to take photos or record videos.
IMPORTANT NOTE: The Point To Fly Function can only be activated in Smart Mode.

HOME MODE
When the Flight Mode Selection Switch is
in the bottom position, the aircraft will be
LANDING
in the Home Mode. The Aircraft Mode LED
LOCATION
will be solid red. To exit the Home Mode,
switch the Mode Switch to Angle/Smart
Mode, then the aircraft will stop moving
and automatically hold its position (with a
suitable GPS signal/lock) and maintain a
level attitude then.
PILOT LOCATION
In Home Mode the aircraft will y in a
straight line in the direction of the pilots'
current location, and automatically land
within 13-26 ft (4-8 m) of the pilot.
NOTICE: In this mode, the Point To Fly Function cant be activated.
CAUTION: Dont switch to Home Mode when you are near bodies of water.

18

CAMERA CONTROLS
GIMBAL CAMERA TILT CONTROL
There is a gimbal tilt mode switch on ST16---S1. When the switch is in
up/middle position, the CGO3+ gimbal camera is in Angle Mode. Use
the slider (C) on the left side of the ST16 to set the tilt position of the
gimbal camera. When the S1 is in bottom position, the gimbal camera is
in Velocity Mode. When the slider (C) is in the middle position, it means
the velocity rate is 0 for the CGO3+, and it will stop tilting up/down.
When the slider (C) is above the middle position, theCGO3+ will start
tilting up. When the slider (C) is below the middle position, the CGO3+
will start tilting down. The distance between the slider(C) and the
middle position decides the velocity rate, the further distance, the
higher velocity it would be.
CAUTION: You MUST stop recording video in order to take still photos.
It will take approximately 5 seconds to capture a still photo and before
you can take another.
CAUTION: ALWAYS stop recording video before turning off Typhoon H
to avoid data loss.

GIMBAL CAMERA PAN CONTROL

There is a gimbal pan mode switch on ST16---S2. When the switch
position is up, the gimbal camera is in Follow Mode. The pan control of
the gimbal camera is now disabled. The gimbal camera will adjust its
yaw direction according to the aircraft s movements. When the switch
is in the middle position, the gimbal camera is in Follow Pan Controllable Mode, the gimbal camera will adjust its pan
direction according to the aircraft s movements.
Meanwhile, the pan control is activated, use the
K1 to set the pan position of the gimbal camera.
When the switch position is down, the gimbal
camera is in Global Mode. The pan direction of
the gimbal camera will be xed regardless of the
aircraft s movements. Use the K1 to set the pan
position of the gimbal camera.

Button A = Take Still Photo Button B = Start/Stop Recording Video

19

Model: Typhoon H

TAKING PHOTOS AND RECORDING VIDEO

The ST16 seamlessly integrates control of the CGO3+ so you can easily
take still photos and start/stop video recording using the corresponding buttons located on top.
To Take A Still Photo
Press the button located near the top left corner of the ST16. You'll hear
an audible shutter sound from the ST16 and the LED indicator on the
front of the CGO3+ will change from glowing solid green to glowing
solid blue. It will take approximately 1-2 seconds to capture the photo
and before you can take another still photo.
To START/STOP Recording Video
Press the button located near the top right corner of the ST16. You'll
hear an audible indication from the ST16 each time the recording
starts/stops. And while video is recording the LED indicator on the front
of the CGO3+ will ash blue and green, and there will be a red dot next
to the time length of the recording near the upper right-hand corner on
the screen of the ST16.
NOTICE: CGO3+ camera is the default selection in ST16. You can take
still photos in the video recording mode. The resolution is set by the
video resolution. In this mode, you will capture still photos from the
video.
CAUTION: Do not change settings when aircraft is further than 1,000
feet from ST16.
fusers are professionals in photography and videography, and want to
adjust manual settings, please follow the steps below:
STEP 1) Press Flight Settings, choose Camera Select, press CGO3+,
press Select, and press OK.
STEP 2) The second left column is available for adjusting the camera
settings, like white balance, exposure, shutter speed and ISO, etc.
STEP 3) Press , and press Video Settings, different video resolutions are
available.

20

VOLTS
N/A

GPS
N/A

SAT
N/AE
N/AN

welcome,Pilot

12:27 AM

Auto

ANGLE

Lock
WB

Sunny

Auto

OBS

Disabled

POS
N/AV

Cloudy

ISO 32
1/250s

GPS
CALIBRATION

ALT
N/Am

12

AWB

Fluorescent

G-SPD

FOLLOW
WATCH

N/A KPH
Incandescent

DIS
N/Am

3840 x 2160 F30

Sunset/sunrise

Pad

TASK
CAMERA

Model Select

CAMERA PARAMETER SETTING

AWB
In the [ Auto
] menu, the user can choose different mode based on the
situation. The camera will adjust parameter according to the light
AWB
automatically when tapping [ Auto
]. When tapping the button [ Lock ], the
parameter at that time will be locked.
In the [ Auto ]menu, the exposure and shutter speed can be adjusted
manually or automatically.
] and you can press the Auto [ Auto ] to change
NOTICE: Tap the icon [
it to M [ M ], which means you can adjust the shutter speed and ISO
manually.
NOTICE: In the taking-picture mode, the resolution is 12,400,000. In
the video recording mode, resolution needs to be applied when taking pictures.
CAUTION: ALWAYS stop recording video before turning off Typhoon
H/CGO3+ to avoid data loss. If you accidentally turn off Typhoon
H/CGO3+ before you stop recording, re-insert the micro SD card (if
removed) and turn the system on again. Wait approximately 20
seconds until the camera LED starts to glow solid green indicating the
last video le was recovered.
CAUTION: When entering the photo capturing mode, video recording
is disabled. You MUST switch to video recording to start recording
videos. During video recording, picture taking (Button A) is accessible. The resolution is set by the video resolution. In this mode, you will
capture still photos.

GPS FUNCTIONALITY

DISABLING GPS

Typhoon H requires a suitable GPS signal/lock in order to start the

motors and to be own. This means it should only be operated
outdoors in open areas that are free from people, vehicles and other
obstructions. In order to acquire a suitable GPS signal/lock it s critical
that the GPS antenna installed in the top of Typhoon H always have a
clear view of the sky (100 minimum clearance required).
WARNING: Do NOT attempt to y near or between tall buildings/obstructions, near or under dense vegetation, structures or indoors. Do
NOT attempt to y Typhoon H with GPS enabled indoors or in any
location known to have poor GPS coverage. Do NOT disable/turn off
GPS unless youre able to properly control Typhoon H in Angle (Pilot)
Mode without GPS assistance and accept ALL responsibility and liability for crashes or y aways.
If the Typhoon loses GPS signal/lock while ying it can only be own in
Angle (Pilot) Mode. Smart Mode and Home Mode, along with their
corresponding features, will no longer work. The Main LED Status
Indicator will ash purple and the LED Status Indicators below the
motors will ash three times per second then will stay off for one (1)
second when the Typhoon loses GPS signal/lock (or if GPS has been
disabled/turned off ).
If the GPS signal/lock is reacquired (after receiving 510 seconds of
suitable GPS signal), Smart Mode and Home Mode will work again.
WARNING: Loss of GPS signal/lock may result in a crash or even a y away.
IMPORTANT NOTE: Crash damage and y aways are NOT covered
under warranty.
NO-FLY ZONES
With a suitable GPS signal/lock it will not be possible to start the
motors, takeoff or y Typhoon H in the 'No-Fly Zones' within a 4 mile
(6.4 kilometer) radius of most major airports.

WARNING: Smart Mode and Home Mode, along with their corresponding features, only work when GPS is active and Typhoon H has a
suitable GPS signal/lock. If you disable/turn off GPS, Typhoon H can
only be own in Angle (Pilot) Mode. If you cannot properly control the
Typhoon in Angle (Pilot) Mode, the aircraft may crash or even 'y
away'.
IMPORTANT NOTE: Crash damage and y aways are NOT covered
under warranty.
We do not typically recommend disabling GPS for any reason,
especially if youre a rst-time or low-time pilot. However, if youre an
experienced pilot that s able to properly control Typhoon H in Angle
(Pilot) Mode, and you do not exceed any altitude/distance limits or y
in any no y zones in your area, you can disable/turn off GPS. Do NOT
disable/turn off GPS unless you accept ALL responsibility and liability
for crashes or y aways.
IMPORTANT NOTE: Every time you turn on Typhoon H, it will default to
having GPS active/on (even if you disabled GPS the last time is was
powered on).
After the ST16 Ground Station/ ST12 Ground Station/Wizard and the
CGO3 are bound successfully, press the GPS Calibration icon, and
then tap the GPS Switch to turn off the GPS.

21

COMPASS CALIBRATION
CAUTION: Do not calibrate the compass in parking garages, close to buildings or near roads with a metal core. For optimum
performance, only calibrate Typhoon H in open spaces, far away from power lines and other metal structures or concrete
buildings.
NOTICE: Be sure to perform the compass calibration procedure at least 11 feet away from the nearest cell phone or other
electronic devices to ensure proper calibration.
STEP 1) Power on the ST16 Ground Station
rst and then the aircraft, and make sure
they are connected correctly. If they are
not connected correctly, the telemetry
data will not display on the screen.

STEP 2) Tap the GPS CALIBRATION icon on the ST16 screen

and choose COMPASS.

STEP 3) Lift Typhoon H airframe straight & level. When the LEDs on two motors start to blink blue and green
separately as illustrated, turn it forward as shown by the red arrow above until the two LEDs turn off.
STEP 4) When the LEDs on another two motors start to blink white and red separately as illustrated, turn the
aircraft 60 to the left and then turn it forward as shown by the red arrow above until the two LEDs turn off.
STEP 5) When the LEDs on another two motors start to blink white and red separately, Turn the aircraft 60
to the left again and then turn it forward as shown by the red arrow above until the two L E D s t u r n o ff .
STEP 6) When the LEDs on another two motors start to blink green and blue separately, Turn the aircraft
60 to the left again and then turn it forward as shown by the red arrow above until the two LEDs turn off.
STEP 7) When the LEDs on another two motors start to blink red and white separately, Turn the aircraft 60
to the left again and then turn it forward as shown by the red arrow above until the two LEDs turn off.
STEP 8) When the LEDs on another two motors start to blink red and white separately, Turn the aircraft 60
to the left again and then turn it forward as shown by the red arrow above until the two LEDs turn off.

22

GPS
CALIBRATION

If the calibration has been successful, all the

LED status indicators will blink continuously,
the Main LED Status Indicator will be solid
green and the ight controller restarts, you
will recognize this when you hear the
acknowledgement tone, the same one you
hear when you switch the system on.

IMPORTANT NOTE: If calibration has failed,

the Main LED Status Indicator will be solid
white and you must repeat the calibration
process. If the calibration continues to fail,
either the site of calibration is unsuitable or
the compass is defective. Refer to your
Yuneec service center.

LED STATUS INDICATIONS

LED STATUS INDICATIONS DURING STARTUP
Main LED Status Indicator
on in Progress

Blinks red and white rapidly

regarding no-y zones

LED STATUS INDICATIONS BEFORE/DURING FLIGHT

Main LED Status Indicator
is in Smart Mode with GPS lock

Glows solid green

Glows solid purple

e Mode
Blinks red, green and blue every 3 seconds
Blinks purple (1 ash per second)

- GPS Disabled
Below Motor Led Status Indicators

Blinks

LED STATUS INDICATIONS FOR CALIBRATION MODES

Main LED Status Indicator
on Mode Entered

Blinks

Glows solid white

CGO3+ CAMERA LED STATUS INDICATIONS

- Without T-card or T-card Memory Full
- WiFi Error
- WiFi Connected

Blinks yellow
Blinks red
Blinks green
Glows solid green
Blinks green, blue slowly

23

NOTICES AND WARNINGS

IMPORTANT NOTE: All safety precautions and warnings, instructions, warranties and other collateral information is subject to change at the sole discretion
of Yuneec. For the most up-to-date information please visit the corresponding product page at www.Yuneec.com or contact the nearest Yuneec office or
authorized distributor.
The following special language terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of property damage and/or possibility of injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and/or serious injury or create a high
probability of superficial injury.
WARNING: Read the ENTIRE quick start guide and instruction manual to become familiar with the features of the product before operating. Failure to
operate the product correctly can result in damage to the product, property and/or cause serious injury.
WARNING: This is a sophisticated consumer product. It must be operated with caution and common sense, and requires some basic mechanical ability.
Failure to operate this product in a safe and responsible manner could result in damage to the product, property and/or cause serious injury. This product
is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the
instructions provided by Yuneec. The quick start guide and instruction manual contain instructions for safety, operation and maintenance. It is essential to
read and follow all the instructions and warnings prior to assembly, setup and/or use in order to operate the product correctly and avoid damage or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

GENERAL SAFETY PRECAUTIONS AND WARNINGS

WARNING: Failure to use this product in the intended manner as described in the quick start guide and instruction manual can result in damage to the
product, property and/or cause serious injury. A Radio Controlled (RC) multirotor aircraft, APV platform, drone, etc. is not a toy! If misused it can cause
serious bodily harm and damage to property.
WARNING: As the user of this product you are solely and entirely responsible for operating it in a manner that does not endanger yourself and others or
result in damage to the product or the property of others.
Keep your hands, face and other parts of your body away from the spinning propellers/rotor blades and other moving parts at all times. Keep items that
could impact or become entangled away from the propellers/rotor blades including debris, parts, tools, loose clothing, etc.
Always operate your aircraft in open areas that are free from people, vehicles and other obstructions. Never fly near or above crowds, airports or buildings.
To ensure proper operation and safe flight performance never attempt to operate your aircraft nearby buildings or other obstructions that do not offer a
clear view of the sky and can restrict GPS reception.
Do not attempt to operate your aircraft in areas with potential magnetic and/or radio interference including areas nearby broadcast towers, power
transmission stations, high voltage power lines, electrical storms, etc.
Always keep a safe distance in all directions around your aircraft to avoid collisions and/or injury. This aircraft is controlled by a radio signal subject to
interference from many sources outside your control. Interference can cause momentary loss of control.
To ensure proper and safe operation of the automatic landing function in Home Mode you must start the motors with the aircraft in a position that has at
least 10 feet (approximately 3 meters) of clear and open space around it and achieve a proper GPS lock.
Do not attempt to operate your aircraft with any worn and/or damaged components, parts, etc. (including, but not limited to, damaged propellers/rotor
blades, old batteries, etc.).
Never operate your aircraft in poor or severe weather conditions including heavy winds, precipitation, lightning, etc.

24

 Always operate your aircraft starting with a fully charged battery. Always land as soon as possible after the first level low voltage battery warning or land
immediately after the second level low voltage battery warning (as indicated by the vibrations and audible alerts from the transmitter/personal ground
station).
Always operate your aircraft when the voltage of the battery in the transmitter/personal ground station is in a safe range (as indicated by the battery charge
status icon on the screen of the transmitter/personal ground station).
Always keep the aircraft in clear line of sight and under control, and keep the transmitter/personal ground station powered on while the aircraft is powered
on.
Always move the throttle control stick down fully and turn off the motors in the event the propellers/rotor blades come into contact with any objects.
Always allow components and parts to cool after use before touching them and flying again.
Always remove batteries after use and store/transport them per the corresponding guidelines.
Avoid water exposure to all electronic components, parts, etc. not specifically designed and protected for use in water. Moisture causes damage to
electronic components and parts.
Never place any portion of the aircraft or any related accessories, components or parts in your mouth as doing so could cause serious injury or even death.
Always keep chemicals, small parts and electronic components out of the reach of children.
Carefully follow the instructions and warnings included with this aircraft and any related accessories, components or parts (including, but not limited to,
chargers, rechargeable batteries, etc.).
CAUTION: The electronic speed controls (ESCs) installed in the TORNADO are not compatible with any other product, and the TORNADO is not compatible
with any other ESCs. Use of any other ESCs in the TORNADO will cause a crash, which may result in damage to the product, property and/or cause serious injury.

LIPO BATTERY WARNINGS AND USAGE GUIDELINES

WARNING: Lithium Polymer (LiPo) batteries are significantly more volatile than alkaline, NiCd or NiMH batteries. All instructions and warnings must be
followed exactly to prevent property damage and/or serious injury as the mishandling of LiPo batteries can result in fire. By handling, charging or using the
included LiPo battery you assume all risks associated with LiPo batteries. If you do not agree with these conditions please return the complete product in
new, unused condition to the place of purchase immediately.
You must always charge the LiPo battery in a safe, well-ventilated area away from flammable materials.
Never charge the LiPo battery unattended at any time. When charging the battery you must always remain in constant observation to monitor the charging
process and react immediately to any potential problems that may occur.
After flying/discharging the LiPo battery you must allow it to cool to ambient/room temperature before recharging.
To charge the LiPo battery you must use only the included charger or a suitably compatible LiPo battery charger. Failure to do so may result in a fire causing
property damage and/or serious injury.
If at any time the LiPo battery begins to balloon or swell, discontinue charging or discharging immediately. Quickly and safely disconnect the battery, then
place it in a safe, open area away from flammable materials to observe it for at least 15 minutes. Continuing to charge or discharge a battery that has begun
to balloon or swell can result in a fire. A battery that has ballooned or swollen even a small amount must be removed from service completely.
Do not over-discharge the LiPo battery. Discharging the battery too low can cause damage to the battery resulting in
reduced power, flight duration or failure of the battery entirely. LiPo cells should not be discharged to below 3.0V each under load.
Store the LiPo battery at room temperature and in a dry area for best results.
When charging, transporting or temporarily storing the LiPo battery the temperature range should be from approximately 40120 F (549 C). Do not
store the battery or aircraft in a hot garage, car or direct sunlight. If stored in a hot garage or car the battery can be damaged or even catch fire.
Never leave batteries, chargers and power supplies unattended during use.

25

 Never attempt to charge low voltage, ballooned/swollen, damaged or wet batteries.

Never allow children under 14 years of age to charge batteries.
Never charge a battery if any of the wire leads have been damaged or shorted.
Never attempt to disassemble the battery, charger or power supply.
Never drop batteries, chargers or power supplies.
Always inspect the battery, charger and power supply before charging.
Always ensure correct polarity before connecting batteries, chargers and power supplies.
Always disconnect the battery after charging.
Always terminate all processes if the battery, charger or power supply malfunctions.
IMPORTANT NOTE: Its safer and better for the longevity of the battery to store it only partially charged for any length of time. Storing the battery
approximately 50% charged is typically best, however, it will take some careful management of the charge time and the use of a volt meter to achieve this
voltage. If you have the equipment and skills to achieve the 50% charge level for storage it is recommended. If not, simply be sure to not store the battery
fully charged whenever possible.
In fact, as long as the battery will be stored at approximately room temperature and for no more than a few weeks before the next use, it may be best to
store the battery in the discharged state after the last flight (as long as the battery was not over-discharged on the last flight).

26

DISCLAIMER
Yuneec Electric Aviation cannot be held liable for any damage, injury or for use of the product in violation with legal regulations, especially in the following
circumstances:
Damage and/or injury as well violation of legal regulations resulting from a failure to comply with the operating instructions or the instructions at
www.yuneec.com, product information, user manual and other legally binding information.
Damage and/or injury as well violation of legal regulations brought about by the influence of alcohol, drugs, medication or mother narcotics which may
impact on the concentration of the user. The same applies to illnesses effecting the concentration of the user (dizziness, tiredness, nausea etc.) or other
factors compromising mental and physical capabilities. Intentionally caused damage, injury or violation of legal regulations.
Any request for compensation caused by an accident resulting from use of the product.
Damage and/or injury as well as violation of legal regulations caused by use of the product in a no-fly zone, e.g. next to an airfield, above a motorway or a
natural conservation area. Malfunction of the product caused by retrofitting or replacement with components which did not come from Yuneec Electric
Aviation.
Damage and/or injury caused by the use of replica parts (non-original parts).
Damage and/or injury as well as violation of legal regulations caused by incorrect operation or misjudgment.
Damage and/or injury caused by damaged spare parts or not using original Yuneec Electric Aviation spare parts.
Damage and/or injury as well as violation of legal regulations caused by ignoring the low voltage battery warning.
Damage and/or injury caused by knowingly and negligibly flying with a damaged model or one which is unfit to fly, e.g. due to dirt, water penetration,
coarse particles, oil or a model which has not been correctly or completely assembled or if the main components exhibit visible damage, defects or missing
parts.
Damage and/or injury as well as violation of legal regulations caused by operating the model in a magnetic field (e.g. high voltage lines,
electricity/transformer stations, radio towers, mobile phone masts etc.), a strong wireless signal environment, no-fly zones, poor visibility and in the event
of vision impairments or other impacts on the pilot which are left unchecked etc...
Damage and/or injury brought about through a violation of the legal regulations for operating the model, in unsuitable weather conditions, e.g. rain, wind,
snow, hail, storms, hurricanes etc.
Damage and/or injury as well as violation of legal regulations caused by force majeure, e.g. collision, fire, explosion, flooding, tsunami, landslide, avalanche,
earthquake or other forces of nature.
Damage and/or injury as well as violation of legal regulations caused by the illegal or immoral use of the model, e.g. capturing videos or recording data
which infringes upon/harms the privacy of other people.
Damage and/or injury as well as violation of legal regulations caused by incorrect use of the batteries, protection systems, chargers or aircraft.
Consequential damage caused by the incorrect operation of any kind of system components and accessory parts, especially memory cards, whereby image
or video material from the camera can become defect.
Any non-compliance with legal obligations, personal injury, material damage and environmental damage caused by use and a failure to comply with the local
laws and regulations.
Damage and/or injury as well as violation of legal regulations caused by hazardous use without sufficient practical experience.
Damage and/or injury as well as violation of legal regulations caused by flying in legally defined no-fly zones. Further losses which do not fall within the
scope of use defined by Yuneec Electric Aviation as improper.
This product is designed for both professional use and personal, private use. The national and international laws and regulations in force as the time of take
off must be adhered to.

27

CERTIFICATION INFORMATION
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE WARNING
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi,
mme si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment.
Cet quipement respecte les limites d'exposition aux rayonnements IC dfinies pour un environnement non contrl

Any

r the latest documents, please check the ocial website.

28