Tyfo SCH-41 Composite: Using Tyfo S Epoxy

Tyfo SCH-41 Composite
using Tyfo S Epoxy
DESCRIPTION
TYPICAL DRY FIBER PROPERTIES
The Tyfo SCH-41 Composite is comprised of

Tyfo S Epoxy and Tyfo SCH-41 reinforcing
fabric, which is NSF-Certified. Tyfo SCH-41 is
a custom, uni-directional carbon fabric orientated
in the 0 o direction. The Tyfo S Epoxy is a twocomponent epoxy matrix.
PROPERTY
TYPICAL TEST VALUE
Tensile Strength
580,000 psi (4.0 GPa)
Tensile Modulus
33.4 x 106 psi (230 GPa)
Ultimate Elongation
USE
Tyfo SCH-41 Fabric is combined with Tyfo

Epoxy to add strength to bridges, buildings, and
other structures.
1.7%
Density
0.063 lbs./in. (1.74 g/cm3)

3
Minimum weight per sq. yd.
19 oz. (644 g/m2)
ADVANTAGES
ICC-ES ESR-2103 listed product

Component of UL listed, fire-rated assembly
NSF/ANSI Standard 61 listed product for
drinking water systems
Improved long-term durability
Good high & low temperature properties
Long working time
High tensile modulus and strength
Ambient cure
100% solvent-free
Rolls can be cut to desired widths prior to
shipping
COMPOSITE GROSS LAMINATE PROPERTIES
COVERAGE
Approximately 600 sq. ft. surface area with 3

to 4 units of Tyfo S Epoxy and 1 roll of Tyfo
SCH-41 Fabric when used with the Tyfo
Saturator.
PACKAGING
Order Tyfo S Epoxy in 55-gallon (208L) drums

or pre-measured units in 5-gallon (19L)
containers. Tyfo SCH-41 Fabric typically
shipped in 24 x 300 lineal foot (0.6m x 91.4m)
rolls. Typically ships in 12 x 13 x 27 (305mm
x 330mm x 686mm) boxes.
ASTM
METHOD
TYPICAL
TEST VALUE
DESIGN VALUE*
Ultimate Tensile Strength in

Primary Fiber Direction
D3039
143,000 psi (986 MPa)

(5.7 kip/in. width)
121,000 psi (834 MPa)

(4.8 kip/in. width)
Elongation at Break
D3039
1.0%
0.85%
Tensile Modulus
D3039
13.9 x 10 psi
(95.8 GPa)
11.9 x 106 psi

(82 GPa)
Flexural Strength
D790
17,900 psi (123.4 MPa)
15,200 psi (104.8 MPa)
Flexural Modulus
D790
452,000 psi (3.12 GPa)
384,200 psi (2.65 GPa)
Longitudinal Compressive
Strength
D3410
50,000 psi
(344.8 MPa)
42,500 psi
(293 MPa)
Longitudinal Compressive
Modulus
D3410
11.2 x 106 psi

(77.2 GPa)
9.5 x 106 psi

(65.5 GPa)
Longitudinal Coefficient of
Thermal Expansion
D696
3.6 ppm./oF
Transverse Coefficient of
Thermal Expansion
D696
20.3 ppm./oF
PROPERTY
Nominal Laminate Thickness
0.04 in. (1.0mm)
0.04 in. (1.0mm)
* Gross laminate design properties based on ACI 440 suggested guidelines will vary slightly. Contact Fyfe Co. LLC engineers to
confirm project specification values and design methodology.
EPOXY MIX RATIO
100.0 component A to 42.0 component B

by volume. (100 component A to 34.5 component
B by weight.)
EPOXY MATERIAL PROPERTIES

Curing Schedule 72 hours post cure at 140o F (60o C).
SHELF LIFE
STORAGE CONDITIONS
Store epoxy at 40o to 90o F (4o to 32o C). Avoid

freezing. Store rolls flat, not on ends, at
temperatures below 100 o F (38 o C). Avoid
moisture and water contamination.
CERTIFICATE OF COMPLIANCE
Will be supplied upon request, complete

with state and federal packaging laws
with copy of labels used.
Material safety data sheets will be supplied
upon request.
Possesses 0% V.O.C. level.
5/15 SCH-41
ASTM
METHOD
TYPICAL
TEST VALUE*
Tensile Strength1
D638
Type 1
10,500 psi
(72.4 MPa)
Tensile Modulus
D638
Type 1
461,000 psi
(3.18 GPa)
Elongation Percent
D638
Type 1
5.0%
Flexural Strength
D790
17,900 psi (123.4 MPa)
Flexural Modulus
D790
452,000 psi (3.12 GPa)
Tg
D4065
180o F (82o C)
PROPERTY
Epoxy - two years in original, unopened and

properly stored containers.
Fabric - ten years in proper storage conditions.
Testing temperature: 70o F (21o C)

Crosshead speed: 0.5 in. (13mm)/min. Grips Instron 2716-0055 - 30 kips
* Specification values can be provided upon request.
1
APPLICATION
HOW TO USE
THE TYFO S COMPOSITE SYSTEM
DESIGN
The Tyfo Fibrwrap System shall be designed

to meet specific design criteria. The criteria
for each project is dictated by the engineer of
record and any relevant building codes and/or
guidelines. The design should be based on the
allowable strain for each type of application and
the design modulus of the material. The Fyfe
Co. LLC engineering staff will provide preliminary
design at no obligation.
INSTALLATION
Tyfo System to be installed by Fyfe Co. LLC

trained and certified applicators. Installation
shall be in strict compliance with the Fyfe Co.
LLC Quality Control Manual.
SURFACE PREPARATION
The required surface preparation is largely

dependent on the type of element being
strengthened. In general, the surface must be
clean, dry and free of protrusions or cavities,
which may cause voids behind the Tyfo
composite. Column surfaces that will receive
continuous wraps typically require only a broom
cleaning. Discontinuous wrapping surfaces
(walls, beams, slabs, etc.) typically require a light
sandblast, grinding or other approved methods
to prepare for bonding. Sharp and chamfered
corners will be rounded off by grinding or using
thickened Tyfo S epoxy (Tyfo WS epoxy or
approved repair mortar). At the time of application,
the substrate shall not have any free moisture
on it. If moisture cannot be avoided, the use of
Tyfo WP (Wet-Prime epoxy) is recommended.
Tyfo Fibr Anchors are incorporated in some
designs. The Fyfe Co. LLC engineering staff will
provide the proper specifications and details based
on the project requirements.
Apply one prime coat of Tyfo S Epoxy on the

substrate by using a roller. Saturate the fabric
by feeding it through the Tyfo Saturator.
Apply using the Tyfo wrapping equipment
or approved hand methods (See the Tyfo
Saturator Manual). Prior to the application of
the saturated fabric, fill any uneven surface
with thickened Tyfo S epoxy. Saturate
and apply subsequent layers of the fabric
according to the Specifications and the
Design Requirements. The use of a roller or
hand pressure, ensure proper orientation of
fibers, release or roll out entrapped air and
ensure that each individual layer is firmly
bedded and adhered to the preceding layer
or substrate. Apply a final coat of thickened
Tyfo S Epoxy and detail all fabric edges,
including butt splice, termination points and
jacket edges. Please refer to the NSF Listing
for the NSF-61 Listed Application.
PROTECTIVE COATINGS
In case of plaster final coating, apply sand by

hand for better bonding surface while the final
coat of epoxy is still tacky. In case of paint final
coating, paint between 24 and 72 hours after final
application of epoxy. If more than 72 hours after
application, prepare the surface of the final coat
of epoxy by light sandblast or hand sanding to
slightly etch the surface.
LIMITATIONS
Application temperature of the epoxy is a

minimum 40o F (4o C) and maximum of 100o F
(38o C). DO NOT THIN, solvents will prevent
proper cure.
FIELD QUALITY CONTROL
Record batch numbers for fabric and epoxy used

each day and note locations of installations.
Measure square feet of fabric and volume of
epoxy used each day.
MIXING
For pre-measured units in 5-gallon (19L)

containers, pour the contents of component
B into the pail of component A. For drums,
premix each component: 100.0 parts of
component A to 42.0 parts of component B by
volume (100 parts of component A to 34.5 parts of
component B by weight). Mix thoroughly for five
minutes with a Tyfo low speed mixer at 400-600
RPM until uniformly blended.
CAUTION!
COMPONENT A - Irritant:
Prolonged contact to the skin may cause

irritation. Avoid eye contact.
COMPONENT B - Irritant:
Corrosive. Contact with skin may cause severe

burns. Avoid eye contact. Product is a strong
sensitizer. Use of safety goggles and chemical
resistant gloves recommended. Remove
contaminated clothing. Avoid breathing vapors.
Use adequate ventilation. Use of an organic
vapor respirator recommended.
SAFETY PRECAUTIONS
Avoid breathing vapors. Avoid contact with eyes

and skin. Use of an approved respirator with an
organic absorption cartridge is recommended
for possible vapors. Rubber gloves, rubber
boots, and protective suits are recommended
for handling and application of this material.
Safety glasses or a face shield are recommended
to prevent eye contact.
FIRST AID
In case of skin contact, wash thoroughly with

soap and water. For eye contact, flush
immediately. For respiratory problems, remove
to fresh air. Wash clothing before reuse.
CLEANUP
Collect with absorbent material, flush with

water. Dispose of in accordance with local
disposal regulations. Uncured material can be
removed with approved solvent. Cured materials
can only be removed mechanically.
SHIPPING LABELS CONTAIN
State specification number with modifications,

if applicable
Component designation
Type, if applicable
Manufacturers name
Date of manufacture
Batch name
State lot number, if applicable
Directions for use
Warnings or precautions by law
KEEP CONTAINER TIGHTLY CLOSED.
NOT FOR INTERNAL CONSUMPTION.
CONSULT MATERIAL SAFETY DATA SHEET
(MSDS) FOR MORE INFORMATION.
KEEP OUT OF REACH OF CHILDREN.
FOR INDUSTRIAL USE ONLY.
Fyfe Co. LLC

Tyfo Fibrwrap Systems
3940 Ruffin Road, Suite C, San Diego, CA 92123
Tel: 858.642.0694 Fax: 858.444.2982
E-mail: info@fyfeco.com www.fyfeco.com
Statement of Responsibility: The technical information and application advice in this publication is based on the present state of our best scientific and practical knowledge.
As the nature of the information herein is general, no assumption can be made as to the products suitability for a particular use or application, and no warranty as to its
accuracy, reliability or completeness, either expressed or implied, is given other than those required by State legislation. The owner, his representative or the contractor is
responsible for checking the suitability of products for their intended use. Field service, where provided, does not constitute supervisory responsibility. Suggestions made
by the Fyfe Co., either verbally or in writing, may be followed, modified or rejected by the owner, engineer or contractor since they, and not the Fyfe Co., are responsible
for carrying out procedure appropriate to a specific application.
5/15 SCH-41
Patented in U.S.A., Canada, and other countries. Copyright 2015 Fyfe Co. LLC 18-15

Tyfo SCH-41 Composite: Using Tyfo S Epoxy

Uploaded by

Copyright:

Available Formats

Tyfo SCH-41 Composite: Using Tyfo S Epoxy

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tyfo SCH-41 Composite: Using Tyfo S Epoxy

Uploaded by

Copyright:

Available Formats

Tyfo SCH-41 Composite

using Tyfo S Epoxy

TYPICAL DRY FIBER PROPERTIES

The Tyfo SCH-41 Composite is comprised of

TYPICAL TEST VALUE

580,000 psi (4.0 GPa)

33.4 x 106 psi (230 GPa)

Tyfo SCH-41 Fabric is combined with Tyfo

0.063 lbs./in. (1.74 g/cm3)

Minimum weight per sq. yd.

19 oz. (644 g/m2)

ICC-ES ESR-2103 listed product

COMPOSITE GROSS LAMINATE PROPERTIES

Approximately 600 sq. ft. surface area with 3

Order Tyfo S Epoxy in 55-gallon (208L) drums

Ultimate Tensile Strength in

143,000 psi (986 MPa)

121,000 psi (834 MPa)

11.9 x 106 psi

17,900 psi (123.4 MPa)

15,200 psi (104.8 MPa)

452,000 psi (3.12 GPa)

384,200 psi (2.65 GPa)

11.2 x 106 psi

9.5 x 106 psi

Nominal Laminate Thickness

0.04 in. (1.0mm)

0.04 in. (1.0mm)

EPOXY MIX RATIO

100.0 component A to 42.0 component B

EPOXY MATERIAL PROPERTIES

Store epoxy at 40o to 90o F (4o to 32o C). Avoid

Will be supplied upon request, complete

17,900 psi (123.4 MPa)

452,000 psi (3.12 GPa)

Epoxy - two years in original, unopened and

Testing temperature: 70o F (21o C)

The Tyfo Fibrwrap System shall be designed

Tyfo System to be installed by Fyfe Co. LLC

The required surface preparation is largely

Apply one prime coat of Tyfo S Epoxy on the

In case of plaster final coating, apply sand by

Application temperature of the epoxy is a

FIELD QUALITY CONTROL

Record batch numbers for fabric and epoxy used

For pre-measured units in 5-gallon (19L)

Prolonged contact to the skin may cause

Corrosive. Contact with skin may cause severe

Avoid breathing vapors. Avoid contact with eyes

In case of skin contact, wash thoroughly with

Collect with absorbent material, flush with

SHIPPING LABELS CONTAIN

State specification number with modifications,

Fyfe Co. LLC

You might also like