The Most Respected Name in Pilot Cer tification

Piper Seminole
Training Supplement

$29.95

Revised 2015-06-03

800-255-2877 904-595-7940

by

B r i n g s P ilot s & A i rl i n e

R e c r u it e r s To g ether
PilotPool places you in front of
airline recruiters before you reach
application minimums. Airlines use
PilotPool to forecast pilot supply
and meet their recruitment goals
by establishing relationships with
pilots in training and pilots building
qualifications.

Target the specific airlines you

want to fly for
Establish a relationship with your
target employer
Compare your qualifications to
other pilots
Project when youll meet
minimums
Upload your resume

Profile Page & Resume

Dashboard w/ Projections

Sign-up for a Free Pilot Profile

PilotPool.com

Airlines

Introduction
Thank you for choosing ATP for your flight program.
ATP flies over 11,000 hours per month to provide over 4,500 FAA certificates
each year. ATP is committed to providing you low prices; efficient, standardized,
and effective flight programs; andmost importantlythe highest level of safety.
To maximize the effectiveness of your flight program, ATPs Piper Seminole
Training Supplement contains a condensed overview of multi-engine
aerodynamics, portions of the Piper Seminole POH, and flight procedures.
You must have a complete knowledge of all information contained in this
supplement prior to the start of your program. This information will assist you
with your training and flight check.
It is critical that you memorize the following:

Emergency Engine Failure Checklists.

V-Speeds.
Answers to all questions contained in the Oral Review section in the
back of the supplement.

The information in this supplement is highly condensed and serves as a good

quick reference, but it must not be used as a substitute for the FAA-approved
pilot's operating handbook required for safe operation of the airplane.
Thank you for giving ATP an opportunity to serve you.

Contents
Engine-Out Aerodynamics................ 1
Aerodynamic Effects of an Engine Failure... 1
Approximate Drag Factors........................... 2
Airspeeds for Max SE Performance.............. 2
Sideslip Versus Zero Sideslip....................... 3
Single-Engine Service Ceiling....................... 4
Single-Engine Absolute Ceiling..................... 4
Climb Performance Factors.......................... 4
Critical Engine............................................... 4
VMC................................................................ 6
Aircraft Systems................................... 8
Engines......................................................... 8
Propellers..................................................... 9
Landing Gear.............................................. 10
Brakes........................................................ 11
Flaps........................................................... 11
Vacuum Pumps........................................... 11
Pitot Static.................................................. 11
Fuel System................................................ 12
Electrical System........................................12
Heater........................................................ 13
Stall Warning Horn.....................................13
Emergency Exit........................................... 14
Inoperative Instruments & Equipment.......14
Garmin G500.............................................. 14
Standby Instruments..................................17
G500 Failures & Partial-Panel....................18
Differences in '79 & '00 Seminoles............21
Performance / Weight & Balance....22
Piper Seminole V-Speeds...........................22
Performance Charts...................................23
Sample Weight & Balance Problem............23
Formulas.................................................... 24
CG Envelope Graph.....................................24
Flight Check Tasks & Procedures....25
Passenger Briefing.....................................25
Pre-Takeoff Briefing...................................25
Normal Takeoff (Flaps 0).........................26
Engine Failure Procedure...........................27
Approach Briefing......................................28
Announced Calls on Approach...................28

Revised 2015-06-03

Stabilized Approach Corridor.....................28

Go Around Philosophy................................29
Normal Landing.......................................... 29
Normal Visual Approach & Landing...........30
ILS Approach One or Two Engines.............32
Non-Precision Straight-In Approach..........33
Circle to Land Approaches Two Engines....34
Go Around / Missed Approach...................35
Holding....................................................... 35
Approach, PT & Holding Power Settings....35
In-Flight Maneuvers....................................35
Clearing Turns for In-Flight Maneuvers......36
VMC Demonstration.....................................36
Maneuvering with One Engine Inop............37
In-Flight Engine Failure Demo....................37
Example SE Drift Down Scenario................39
Airstart Procedure.....................................39
Emergency Descent...................................40
Recovery from Unusual Attitudes...............40
Spin Awareness.......................................... 41
Private Pilot Multi-Engine Add-On..42
Steep Turns................................................ 42
Maneuvering During Slow Flight.................42
Stall Recovery............................................. 43
Power-Off Stall........................................... 44
Power-On Stall............................................ 44
Commercial Multi-Engine Add-On..46
Steep Turns................................................ 46
Maneuvering During Slow Flight.................46
Power-Off Stall........................................... 47
Power-On Stall............................................ 48
Accelerated Stall.........................................48
Short Field Takeoff & Climb (Flaps 0)......49
Short Field Visual Approach & Landing.....50
CFI Multi-Engine Add-On.................51
Airspeed Drag Demonstration...................51
Airline Transport Pilot.......................52
Steep Turns................................................ 52
Approach to Stall in Approach Config........52
Approach to Stall in Landing Config...........53
Oral Review.........................................54
Sample Oral Questions...............................55

SECTION 1

Engine-Out Aerodynamics

Aerodynamic Effects of an Engine Failure

When an engine failure occurs in a multi-engine aircraft, asymmetric thrust and

drag cause the following effects on the aircrafts axes of rotation:

Pitch Down (Lateral Axis)

Loss of accelerated slipstream over the horizontal stabilizer causes it to produce
less negative lift, causing the aircraft to pitch down. To compensate for the
pitch down effect, additional back pressure is required.
The Seminole has a lesser pitch-down effect than most light
twins because the T-tail configuration removes the horizontal
stabilator from the accelerated slipstream.

Roll Toward the Failed Engine (Longitudinal Axis)

The wing produces less lift on the
side of the failed engine due to
the loss of accelerated slipstream.
Reduced lift causes a roll toward the
failed engine and requires additional
aileron deflection into the operating
engine.

Yaw Toward the Dead Engine (Vertical Axis)

Loss of thrust and increased drag from the
windmilling propeller cause the aircraft to yaw
toward the failed engine. This requires additional
rudder pressure on the side of the operating
engine. Dead foot, dead engine.

VIDEO: Visit ATPFlightSchool.com/students for an interactive

multi-engine aerodynamics presentation. Requires Flash Player.
e-learning

Engine-Out Aerodynamics 1

Engine Inoperative Climb Performance

Climb performance depends on the excess power needed to overcome drag.
When a multi-engine airplane loses an engine, the airplane loses 50% of its
available power. This power loss results in a loss of approximately 80% of the
aircrafts excess power and climb performance. Drag is a major factor relative to
the amount of excess power available. An increase in drag (such as the loss of
one engine) must be offset by additional power. This additional power is now
taken from the excess power, making it unavailable to aid the aircraft in climb.
When an engine is lost, maximize thrust (full power) and minimize drag (flaps
and gear up, prop feathered, etc.) in order to achieve optimum single-engine
climb performance.

Approximate Drag Factors per the Piper Seminole POH

1.
2.
3.
4.

Flaps 25.................................. -240 FPM

Flaps 40.................................. -275 FPM
Windmilling Prop................. -200 FPM
Gear Extended...................... -250 FPM
ATPs experience indicates more than -200 FPM drag from the
windmilling prop.

Under FAR Part 23:

The FAA does not require multi-engine airplanes that weigh less than 6,000
pounds or have a VSO speed under 61 knots to meet any specified single-engine
performance criteria. No single engine climb performance is required. Actual
climb performance is documented by the manufacturer.
The Seminoles max TOW is 3,800 pounds and VSO speed is 55
KIAS. Review the POH for single-engine climb performance for
specific conditions.

Airspeeds for Max Single-Engine Performance

VXSE

The airspeed for the steepest angle of climb on single-engine.

VYSE

The airspeed for the best rate of climb on single-engine. (Or for the slowest loss
of altitude on drift-down.) Blueline is the marking on the airspeed indicator
corresponding to VYSE at max weight.

2 Engine-Out Aerodynamics

Sideslip Versus Zero Sideslip

During flight with one engine inoperative, proper pilot technique is required to
maximize aircraft performance. An important technique is to establish a Zero
Sideslip Condition.

Sideslip Condition (Undesirable)

When an engine failure occurs, thrust from the operating engine yaws the
aircraft. To maintain aircraft heading with the wings level, rudder must be
applied toward the operating engine. This rudder force results in the sideslip
condition by moving the nose of the aircraft in a direction resulting in the
misalignment of the fuselage and the relative wind. This condition usually
allows the pilot to maintain aircraft heading; however, it produces a high drag
condition that significantly reduces aircraft performance.
Relative
Wind

Failed
Engine

Sideslip Condition:
Ball Centered & Wings Level, Aircraft Tracking North

Zero Sideslip Condition (Best Performance)

The solution to maintaining aircraft heading and reducing drag to improve

performance is the Zero Sideslip Condition. When the aircraft is banked into the
operating engine (usually 2-5), the bank angle creates a horizontal component
of lift. The horizontal lift component aids in counteracting the turning moment
of the operating engine, minimizing the rudder deflection required to align the
longitudinal axis of the aircraft to the relative wind. In addition to banking into
the operating engine, the appropriate amount of rudder required is indicated
by the inclinometer ball being split towards the operating engine side. The
Zero Sideslip Condition aligns the fuselage with the relative wind to minimize
drag and must be flown for optimum aircraft performance.

Horizontal
Component
of Lift

Failed
Engine

Zero Sideslip Condition:

2-5 Bank into Operating Engine

Engine-Out Aerodynamics 3

Single-Engine Service Ceiling

Single-engine service ceiling is the maximum density altitude at which the
single-engine best rate of climb airspeed (VYSE) will produce a 50 FPM rate of
climb with the critical engine inoperative.

Single-Engine Absolute Ceiling

Single-engine absolute ceiling is the maximum density altitude that an aircraft
can attain or maintain with the critical engine inoperative. VYSE and VXSE are
equal at this altitude. The aircraft drifts down to this altitude when an engine
fails.

Climb Performance Depends on Four Factors

Airspeed: Too little or too much will decrease climb performance.

Drag: Gear, Flaps, Cowl Flaps, Flight Control Deflection, Prop, and
Sideslip.
Power: Amount available in excess of that needed for level flight.
(Engines may require leaning due to altitude for max engine
performance.)
Weight: Passengers, baggage, and fuel load greatly affect climb
performance.

Critical Engine
The critical engine is the engine that, when it fails, most adversely affects the
performance and handling qualities of the airplane.
The Seminole is equipped with a counter-rotating propeller
on the right engine. The failure of either engine has the same
effects on performance. This is why the Seminole does not have
a critical engine.

On most multi-engine aircraft, both propellers rotate clockwise as viewed from

the cockpit. By understanding the following factors when flying an aircraft that
has both propellers rotating clockwise, it will be apparent that a left-engine
failure makes the aircraft more difficult to fly than a right-engine failure. The
clockwise rotation of the props contributes to the following factors that cause
the left engine to be critical:

P P-Factor
A Accelerated Slipstream
S Spiraling Slipstream
T Torque
4 Engine-Out Aerodynamics

P-Factor (Yaw)

Both propellers turn clockwise as viewed from the

cockpit. At low airspeeds and high angles of attack,
the descending blade produces more thrust than
the ascending blade due to its increased angle of
attack. Though both propellers produce the same
overall thrust, the descending blade on the right
engine has a longer arm from the CG (or greater
leverage) than the descending blade on the left
engine. The left engine produces the thrust closest to center line. The yaw
produced by the loss of the left engine will be greater than the yaw produced
by the loss of the right engine, making the left engine critical.

Accelerated Slipstream (Roll and Pitch)

P-Factor causes more thrust to be produced on the right side of the propeller.
This yields a center of lift that is closer to the aircraft's longitudinal axis on the
left engine and further from the
longitudinal axis on the right
engine and also results in less
negative lift on the tail. Because of
this, the roll produced by the loss
of the left engine will be greater than the roll produced by the loss of the right
engine, making the left engine critical.

Spiraling Slipstream (Yaw)

A spiraling slipstream from the left engine hits the

vertical stabilizer from the left, helping to counteract
the yaw produced by the loss of the right engine.
However, with a left engine failure, slipstream
from the right engine does not counteract the yaw
toward the dead engine because it spirals away
from the tail, making the left engine critical.

Torque (Roll)

For every action, there is an equal and opposite reaction. Since the propellers
rotate clockwise, the aircraft will tend to roll counterclockwise. When the
right engine is lost, the aircraft will roll to the right. The right rolling tendency,
however, is reduced by the
torque created by the left engine.
When the left engine is lost, the
aircraft will roll to the left, and
the torque produced by the right
engine will add to the left rolling tendency requiring more aileron input, which
increases drag, making the left engine critical.
Engine-Out Aerodynamics 5

Summary

On most light multi-engine aircraft when the critical engine is inoperative, both
directional control and performance suffer more than when the non-critical
engine is inoperative.

VMC

VMC is the minimum airspeed at which directional control can be maintained

with the critical engine inoperative. VMC speed is marked on the airspeed
indicator by a red radial line. Aircraft manufacturers determine VMC speed based
on conditions set by the FAA under FAR 23.149:
1.
2.
3.
4.
5.

Most Unfavorable Weight and Center of Gravity

Standard Day Conditions at Sea Level (Max Engine Power)
Maximum Power on the Operating Engine (Max Yaw)
Critical Engine Prop Windmilling (Max Drag)
Flaps Takeoff Position, Landing Gear Up, Trimmed for Takeoff (Least
Stability)
6. Up to 5 of Bank into the Operating Engine

Any change to the above conditions changes VMC speed, possibly significantly.
The following summarizes how VMC may be affected by the above conditions:

1. Most Unfavorable Weight and Center of Gravity

The certification test allows up to 5 bank into the operating engine. In a given
bank, the heavier the aircraft, the greater the horizontal component of lift that
adds to the rudder force. As weight increases, the horizontal component of lift
increases, which added to the rudder, decreases VMC. As the center of gravity
moves forward, the moment arm between the rudder and the CG is lengthened,
increasing the leverage of the rudder. This increased leverage increases the
rudders effectiveness and results in a lower VMC speed.

2. Standard Day Sea Level

Standard conditions yield high air density that allows the engine to develop
maximum power. An increase in altitude or temperature (a decrease in air
density) will result in reduced engine performance and prop efficiency. This
decreases the adverse yaw effect. VMC speed decreases as altitude increases.

3. Maximum Power On The Operating Engine

When the operating engine develops maximum power, adverse yaw is

increased toward the inoperative engine. The pilot must overcome this yaw
to maintain directional control. Any condition that increases power on the
operating engine will increase VMC speed. Any condition that decreases power
on the operating engine (such as power reduction by the pilot, an increase in
altitude, temperature, low density, or aging engine) will decrease VMC.

6 Engine-Out Aerodynamics

4. Critical Engine Prop Windmilling

When the propeller is in a low pitch position (unfeathered), it presents a large

area of resistance to the relative wind. This resistance causes the engine to
windmill. The windmilling creates a large amount of drag and results in a
yawing moment into the dead engine. When the propeller is feathered, the
blades are in a high pitch position, which aligns them with the relative wind,
minimizing drag. A feathered prop will decrease drag and lower VMC.

5. Flaps Takeoff Position, Landing Gear Up, Trimmed for Takeoff

When the gear is extended, the gear and gear doors have a keel effect, reducing
the yawing tendency and decreasing the VMC speed. Extended flaps have a
stabilizing effect that may reduce VMC speed.

6. Up to 5 Bank into the Operating Engine

When the wings are level, only the rudder is used to stop the yaw produced by
the operating engine (sideslip condition). Banking into the operating engine
creates a horizontal component of lift which aids the rudder force. With this
horizontal component of lift and full rudder deflection, VMC is at the lowest
speed. VMC increases with decreasing bank by a factor of approximately 3 knots
per degree of bank angle.
At VMC, the rudder pedal force required to maintain control must
not exceed 150 pounds and it must not be necessary to reduce
power of the operative engine(s). During the maneuver, the
airplane must not assume any dangerous attitude and it must be
possible to prevent a heading change of more than 20.
Piper determined VMC for the Seminole at 1,500' MSL with a
weight of 2,730 lbs. and 5 bank into the operating engine. The
test results were then computed to sea level conditions.
NOTE: Each aircraft is different and may be subject to different
handling qualities than discussed here. Recovery from loss of
directional control should always follow the guidelines of the
POH and FAA Airplane Flying Handbook.

Engine-Out Aerodynamics 7

SECTION 2

Aircraft Systems

Engines
The Seminole is equipped with two Lycoming, 4-cylinder, 0-360 (opposed, 360
cubic inch) engines rated at 180 horsepower at 2700 RPM. The right engine is
designated as an LO-360 due to the fact that it rotates to the left. The engines
are direct drive (crankshaft connected directly to the propeller), horizontally
opposed (pistons oppose each other), piston driven, carbureted and normally
aspirated (no turbo or supercharging). Engine ignition is provided through the
use of engine-driven magnetos which are independent of the aircraft's electrical
system and each other.

Carburetor Icing

Lycoming

Horizontally Opposed

Air Cooled

Normally Aspirated

Direct Drive

Under certain moist atmospheric conditions at temperatures of 20 to 70 F

(-5 to 20 C), it is possible for ice to form in the induction system, even in
summer weather. This is due to the high air velocity through the carburetor
venturi and the absorption of heat from this air by vaporization of the fuel.
To avoid this, the carburetor heat is provided to replace the heat lost by
vaporization. The initial signs of carburetor ice can include engine roughness
and a drop in manifold pressure. Carburetor heat should be selected on if
carburetor ice is encountered. Adjust mixture for maximum smoothness.

8 Aircraft Systems

Propellers
The Seminole is equipped with Hartzell two-bladed, controllable pitch, constant
speed, full feathering metal propellers.

Controllable Pitch

Controllable pitch is the ability to control engine RPM by varying the pitch of
the propeller blades. When the blue propeller control handle is moved forward,
oil pressure, regulated by a propeller governor, drives a piston, which moves the
blades to a low pitchhigh RPM (unfeathered) position. When the blue propeller
control handle is moved aft, oil pressure is reduced by the propeller governor.
This allows a nitrogen-charged cylinder, spring, and centrifugal counterweights
to drive the blades to a high pitchlow RPM (feathered) position.

Constant Speed

After RPM setting is selected with the blue propeller control handles, the
propeller governor will automatically vary oil pressure inside the propeller hub
to change the propeller blade pitch in order to maintain a constant engine RPM.
Because of this, changes in power setting (manifold pressure) and flight attitude
will not cause a change in RPM.

Full Feathering

When the propeller blades are in alignment with the relative wind, they are
feathered. Feathered propeller blades reduce the drag caused by the blade area
exposed to the relative wind. Feathering the propeller blades on the Seminole is
accomplished by moving the blue propeller control handle fully aft past the low
RPM detent, into the FEATHER position. The propeller takes approximately six
seconds to feather. When feathering the propeller, the mixture should be placed
to cutoff to stop engine combustion and power production.
The Seminole is equipped with a centrifugal stop pin that prevents propeller
feathering below 950 RPM. The purpose of this is to allow the propeller blades
to remain in a low pitch upon engine shutdown. This will prevent excessive
loads on the engine starter during the next engine start.
Regardless of the Prop Lever position, if oil pressure is lost, the propeller will
feather when the RPM is above 950 RPM. Typically, RPM will be above 950 in
flight and on takeoff roll and landing roll due to airflow over the propeller.

Propeller Overspeed

Propeller overspeed is usually caused by a malfunction in the propeller

governor which allows the propeller blades to rotate to full low pitch. If
propeller overspeed should occur, retard the throttle. The propeller control
should be moved to full DECREASE RPM and then set if any control is available.
Airspeed should be reduced and throttle used to maintain a maximum of 2700
RPM.
Aircraft Systems 9

Landing Gear
The Seminole is equipped with hydraulically actuated, fully retractable, tricycletype landing gear. Hydraulic pressure for gear operation is provided by an
electrically powered, reversible hydraulic pump. The gear is held in the up
position solely by hydraulic pressure. Springs assist in gear extension and in
locking the gear in the down position. After the gear is down and the downlock
hooks engage, springs maintain force on each hook to keep it locked until it is
released by applying hydraulic pressure with the gear selector.
A gear warning system is activated under any of the following conditions:
1. The gear is not locked down with the throttle lever positioned below
approximately 15" manifold pressure (MP) on one or both engines.
2. The gear is not locked down with wing flaps selected to 25 or 40.
3. The gear handle is in the up position on the ground (tested only by
authorized maintenance personnel).
Gear retraction on the ground is prevented by a squat switch located on the
left main landing gear. On the ground, the switch is open, preventing electrical
current from reaching the hydraulic pump. Once airborne, the strut becomes
fully extended, closing the switch that allows current to reach the hydraulic
pump.
In the event of a hydraulic malfunction, the landing gear may be extended
by the use of the red emergency gear extension knob. After placing the gear
selector in the down position, pulling the red emergency gear extension knob
releases the hydraulic pressure which is holding the gear in the up position
and allows the gear to free-fall down. The positive gear down indication is 3
green lights. Emergency gear extension is limited to a maximum of 100 KIAS
due to air-load on the nose gear. When dealing with a suspected landing gear
problem, it is important to verify the position of the navigation light switch. This
switch will cause the green lights to be dimmed and, in some cases, make them
impossible to see during the day. As with any emergency or abnormality, always
refer to the appropriate checklist.
NOTE: If hydraulic pressure is lost with gear retracted, the gear will
free-fall.

The nose wheel is steered through the use of the rudder pedals and is steerable
30 degrees either side of center.

10 Aircraft Systems

Brakes
The Seminole is equipped with hydraulically actuated disk brakes on the main
landing gear wheels. Braking is accomplished by depressing the tops of the
rudder pedals. The hydraulic system for the brakes is independent of that for the
landing gear. The brake fluid reservoir for servicing is located in the nose cone.
To set the parking brake, hold the brakes and pull the black parking brake knob.
All ATP Seminoles are equipped with heavy duty brakes. Refer
to the POH to make the required adjustment to performance
calculations.
The parking brake is not to be used in training or flight checks
with ATP.

Flaps
The Seminole is equipped with a manual flap system. The flaps are extended
with a lever located between the two pilot seats. Flap settings are 0, 10, 25
and 40 and are spring-loaded to return to the 0 position.
ATP operations require Flaps 25 for all landings except the short
field, which requires Flaps 40. Flaps 25 causes a gear warning
indication if the gear is not down.

Vacuum Pumps
The Seminole is equipped with two engine-driven vacuum pumps. The vacuum
system operates the attitude gyro and, on aircraft without slaving mechanisms
installed, the HSI. Suction limits are 4.8 to 5.2 inches of mercury at 2000 RPM.
The failure of a vacuum pump is indicated by an annunciator panel light and a
red, pump inoperative indicator on the vacuum gauge. In most circumstances,
the failure of one pump alone will not cause the loss of any instruments because
the remaining pump should handle the entire vacuum demand.

Pitot Static
The heated pitot tube and static port are located underneath the left wing.
An alternate static source is located inside the cabin under the left side of the
instrument panel for use in the event of static port blockage. When using the
alternate static source, the storm window and cabin vents must be closed,
and the heater and defroster must be turned on. This will reduce the pressure
differential between the cockpit and the atmosphere, reducing pitot static error.
The pitot static instruments are the airspeed indicator, altimeter, and VSI.

Aircraft Systems 11

Fuel System
The Seminole, which uses 100 low lead avgas (blue), is equipped with two
55-gallon bladder nacelle tanks. One gallon is unusable in each tank.
There are two engine-driven and two electrically driven fuel pumps. The electric
fuel pumps are used for engine start, takeoff, landing, and fuel selector changes.
ATP uses the electric fuel pumps for in-flight maneuvers, except
for steep turns.

The aircraft is equipped with a three-position fuel selector for each engine. The
positions are ON, OFF, and X-FEED (cross feed). The fuel selectors remain in
the ON position during normal operations, and each engine draws fuel from
the tank on the same side as the engine. When X-FEED is selected, the engine
draws fuel from the tank on the opposite side. Fuel cannot be transferred from
tank to tank. Crossfeed operation is limited to straight and level flight only.
The correct procedure for crossfeed operations to supply the left engine with
fuel from the right tank is:
1.
2.
3.
4.
5.

Left engine electric boost pump on.

Left fuel selector selected to X-FEED.
Check left fuel pressure.
Left engine electric boost pump off.
Check fuel pressure.

Electrical System
The Seminole is equipped with a 14-volt electrical system which utilizes pushpull type circuit breakers; a 12-volt, 35 amp hour battery; and two 70-amp,
engine-driven alternators. Voltage regulators maintain constant 14-volt output
from each alternator at varying engine RPMs, effectively sharing the electrical
load. Loss of one alternator is indicated by an annunciator light and a zero
indication on the loadmeter. The remaining alternator will normally provide
adequate electrical power.
An over-voltage relay in each alternator circuit provides system protection
by taking an alternator offline if its output exceeds l7-volts. If this occurs, the
ALT annunciator will illuminate. The battery is used as a source of emergency
electrical power and for engine starts. High drain items include the lights, vent
fan, heater, gear hydraulic pump, radios, and PFD/MFD (if applicable). If an
electrical problem arises, always check circuit breakers. If a circuit breaker is
popped, reset only one time.

12 Aircraft Systems

Heater
Heat to the cabin is supplied by a Janitrol gas combustion heater located in
the nose compartment. Air from the heater is distributed by a manifold to
the ducts along the cabin floor to outlets at each seat and to the defroster
outlet. Operation of the heater is controlled by a three-position switch located
on the instrument panel labeled CABINHEAT, OFF, and FAN. Airflow and
temperature are regulated by the three levers to the right of the switch: AIR
INTAKE, TEMP, and DEF.
For cabin heat, the AIR INTAKE lever must be fully open and the CABIN HEAT
switch on. This simultaneously starts fuel flow and ignites heater. During ground
operation, it also activates the ventilation blower. When cabin air reaches
the temperature selected on the TEMP lever, ignition of the heater cycles
automatically to maintain the selected temperature.
Two safety switches located on the front of the heater unit prevent both fan
and heater operation when the air intake lever is in the closed position. When
the heater is on, a ventilation blower actuates any time the landing gear is
extended. In flight, a micro switch, which actuates when the gear is retracted,
turns off the ventilation blower so that the cabin air is circulated by ram air
pressure only.
An overheat switch in the heater acts as a safety device to render the heater
inoperative if a malfunction should occur. Should the switch deactivate the
heater, the red HEATER OVER TEMP annunciator light on the instrument panel
will illuminate. The overheat switch is located on the aft inboard end of the
heater vent jacket. A red reset button is located on the heater shroud in the
nose cone compartment.
To prevent activation of the overheat switch upon normal heater shutdown
during ground operation, turn the three-position switch to FAN for two
minutes with the air intake lever in the open position before turning the switch
off. During flight, leave the air intake open for a minimum of 15 seconds after
turning the switch to off.
Fuel is supplied to the heater at a rate of gallon per hour from downstream of
the left fuel selector and filter.
To introduce outside, unheated air into the cabin during flight, the AIR INTAKE
lever should be open and the CABIN HEAT off. A fresh air blower is installed to
provide airflow during ground operation. It is operated by a high/low blower
fan switch.

Stall Warning Horn

The Seminole is equipped with two electric stall detectors located on the left
wing. The inboard detector provides stall warning at flaps 25 or 40 and the
outboard at flaps 0 or 10. The purpose of the two tabs is to provide adequate
stall warning at varied angles of attack. The electric stall tabs are deactivated on
the ground through the use of the squat switch on the left main landing gear.
Aircraft Systems 13

Emergency Exit
The emergency exit is the pilots left side window. Use this when emergency
egress becomes necessary on the ground and the main entry door is
unavailable due to fire, etc. The emergency exit release handle is located
beneath the thermoplastic cover on the vertical post between the first and
second left side windows. To exit the aircraft, remove the thermoplastic cover,
pull the release handle forward and then push the window out. The window
then will fall free from the fuselage.

Inoperative Instruments & Equipment per FAR 91.213

ATPs aircraft do not operate under the guidance of a minimum equipment list
(MEL), and instead operate in accordance with the following FAR 91.213 subpart.
Because this is only an excerpt, the complete subpart should be referred to if
necessary:
(3) The inoperative instruments and equipment are -(i) Removed from the aircraft, the cockpit control placarded, and the
maintenance recorded in accordance with 43.9 of this chapter; or
(ii) Deactivated and placarded Inoperative. If deactivation of the
inoperative instrument or equipment involves maintenance, it must be
accomplished and recorded in accordance with part 43 of this chapter;
(4) A determination is made by a pilot, who is certificated and appropriately
rated under part 61 of this chapter, or by a person, who is certificated
and appropriately rated to perform maintenance on the aircraft, that the
inoperative instrument or equipment does not constitute a hazard to the
aircraft.

Garmin G500
2012 and later model Piper Seminoles are equipped with the Garmin G500
electronic flight deck.
G500-equipped aircraft are available only at select training
centers. Visit ATPFlightSchool.com/locations to find out if
your training center requires you to study the following G500
information.

PRIMARY FLIGHT
DISPLAY (PFD)

14 Aircraft Systems

MULTI-FUNCTION
DISPLAY (MFD)

G500 Differences

The G500 powers on and off with the battery master, not the avionics
master.
There are no vacuum driven instruments, vacuum pumps, or suction
gauge. Instruments are electrically powered.
The standby attitude indicator must be erected on power-up by pulling
the cage knob.
Test the standby attitude battery as directed by the After Start Checklist
by pressing and holding the STBY PWR button until amber LED
begins flashing. A continuous green light beneath TEST during the
full sequence indicates that the battery is good. A red light illuminated
anytime during the test indicates that the battery is not charged and
may require replacement.
The standby attitude indicator warning light will blink for
approximately 1 minute when the battery master switch is turned off.
DO NOT press the SBY PWR button as it causes continuous operation
of the gyro on its emergency battery. Exit the airplane with either a
blinking LED or red flag.
G500 equipped Seminoles do not have a conventional turn coordinator.
A slip-skid indicator is located at the top of the attitude indicator. Step
on the brick instead of the ball. Use the reference lines and the
magenta line that appears above the heading indicator to identify a
standard rate or half-standard rate turn.
Outside air temperature (OAT) displays on PFD under the airspeed tape.
There is no OAT probe or analog gauge between the windows.
Ground track can be identified on the heading indicator by a small
magenta diamond near the lubber line (only visible when ground track
is different than heading).
The digital altitude and airspeed readouts are very sensitive and can
cause some pilots to continuously make corrections for insignificant
deviations. Pilot action - Dont overcorrect for deviations of a few
feet. Crosscheck digital and analog standby instruments to avoid the
tendency to overcorrect.
Refer to the complete G500 Pilot's Guide on Student Resources
at ATPFlightSchool.com/students or in the ATP Flight School App
Library.

Aircraft Systems 15

G500 Components
The G500 is comprised of 6 main components:

Primary Flight Display (PFD, left) and

Multi-Function Display (MFD, right)
Attitude Heading Reference System (AHRS)
Air Data Computer (ADC)
Magnetometer
Temperature Probe
Dual Garmin GNS 430 GPS

The PFD (left) shows primary flight information in place of traditional pitotstatic and gyroscopic instruments and also provides an HSI for navigation. ATP
procedures call for configuring the MFD (right) to display traffic information
service (TIS).
The Attitude Heading Reference System (AHRS) contains tilt sensors,
accelerometers, and rate sensors to provide attitude and heading information
on the PFD.
The Air Data Computer (ADC) compiles information from the pitot-static system
and an outside air temperature sensor to provide pressure altitude, airspeed,
vertical speed, and outside air temperature on the PFD.
The magnetometer senses the earth's magnetic field and sends data to the
AHRS for processing to determine magnetic heading.
The temperature probe provides outside air temperature (OAT) data to the ADC.
The dual Garmin GNS 430 GPSs provide input to the AHRS and PFD/MFD.
CAUTION: The GNS 430 and G500 units each have their own
databases. Navigation, terrain and map information on the G500
Multi-Function Display (MFD) may not be current and is not to be
used for navigation. Use the G500 MFD for traffic information.

16 Aircraft Systems

G500 PFD Functions

These buttons toggle the function of the PFD knob.
Set heading bug -

HDG

Set course -

CRS

Set altitude bug and alerter -

ALT

Set V/S Bug -

V/S

(push PFD knob to set heading bug to current heading.)

(when in VLOC mode)

(do not use)

Altimeter setting - BARO

CDI needle indicates NAV source: green for VLOC / magenta for
GPS.

Standby Instruments
Standby Attitude Indicator
An electrical standby attitude indicator is powered and charged by the electrical
system during normal operations. During an electrical failure, the standby
attitude indicator will continue operating from its internal dedicated battery
for approximately 60 seconds while and an amber blinking LED prompts you
to press the STBY PWR button, which continues operation until the internal
battery is depleted. A fully charged standby attitude indicator battery should
provide up to 1 hour of normal standby attitude indicator operation, however
a situation requiring use of the standby attitude indicator is an emergency. Exit
IMC and land as soon as possible.
If the pilot fails to activate the standby battery within 60 seconds,
the STBY PWR button can still be pressed to activate the standby
battery, however the gyro may not be oriented to the airplane
depending on the time elapsed prior to pressing the STBY PWR
button. Press the STBY PWR button while the amber LED is
blinking for best results.

Standby Attitude Indicator Battery Check

Prior to flight, the electric standby indicator battery must be tested. In order to
accomplish the test, aircraft electrical power must be on (Battery Master ON)
and the standby attitude indicator gyro must be fully operational with the red

Aircraft Systems 17

gyro flag out of view. Test the standby battery as called for by the After Start
Checklist.

Press and hold the STBY PWR button for approximately four seconds.
This puts the gyro in a one-minute battery test mode. The amber LED
next to STBY PWR will flash during the test sequence.
A continuous green light illuminated beneath TEST during the full
sequence indicates that the standby battery is good.
A red light illuminated anytime during the test indicates that the
battery is not charged and may require replacement. Contact
maintenance.

Standby Attitude Indicator Shutdown

During a normal shutdown following the Shutdown Terminate Checklist, do
not press the STBY PWR button. Doing so activates emergency operation and
depletes the internal standby battery. Turn the battery master switch OFF when
prompted by the checklist. Allow the amber LED to blink for approximately
60 seconds, followed by the appearance of the red gyro warning flag, which
indicates the unit is powered down.

Standby Altimeter & Airspeed Indicator

The pitot-static system provides information to the standby altimeter and
airspeed indicator.

G500 Failures & Partial-Panel Approaches

For partial panel training and checkrides, the two most common training
scenarios are simulated AHRS failure and PFD failures.
Failure Condition

Simulated By

Instrument
Approaches Available

AHRS Failure

Cover Attitude
Indicator (ADI)

All precision and nonprecision

PFD Failure

Dim PFD/MFD
screens

Only GPS approach

Electrical Failure

No simulated failure
available

None

ADC Failure

No simulated failure
available

All precision and nonprecision

18 Aircraft Systems

Circuit breaker-simulated failures are prohibited in ATP aircraft.

Piper and Garmin advise against pulling circuit breakers as a
means of simulating failures on the Garmin G500 system. Pulling
circuit breakersor using them as switcheshas the potential to
weaken the circuit breaker to a point at which it may not perform
its intended function. Also reference Advisory Circulars 120-80,
23-17B, and 43.13-1B.

Attitude and Heading Reference System (AHRS) Failure

Indications:
1. The sky/ground presentation is removed.
2. A red X appears across the Attitude Direction Indicator (ADI).
3. Yellow ATTITUDE FAIL and HDG alert messages appear on the PFD.
4. A TRK message appears to the right of the ground track at the top of
the compass rose.
5. Rate-of-turn information is unavailable.
6. HDG LOST, HDG FAULT, and "TRK TRAFFIC alert messages appear on
the MFD.

AHRS Failure
The PFD continues displaying airspeed, altitude, vertical speed, compass rose
and ground track. Ground track and compass rose indications are supplied by
GPS, indicated by a TRK message. Any precision or non-precision approach is
available using the HSI on the PFD.
Pilot Action
1. Use standby attitude indicator.
2. Continue using HSI on PFD. Verify track against magnetic compass
heading.
3. Precision (ILS) and non-precision (GPS, Localizer, and VOR) approaches
can be accomplished.

PFD Failure
Indications
1. PFD Screen is dark.

Aircraft Systems 19

Pilot Action
1. Refer to the standby instruments.
2. Use the GPS CDI page for navigation and approaches.
CLR - Press and hold for 3 seconds to return to default CDI page.
3. Only GPS non-precision approaches can be accomplished.
During an MFD failure, with the PFD functioning normally, all
approaches are available for use.

Electrical Failure

Indication
1. The G500 and GPS systems will be inoperative / dark.
2. The STBY PWR button on the standby attitude indicator will begin
blinking.
Pilot Action
1. Use standby attitude indicator. Press the "STBY PWR" button right of the
blinking LED to continue operating using its internal battery.
2. Use standby airspeed, altimeter and compass.
3. Declare an emergency and exit IMC as soon as practicable. The
manufacturer does not specify the endurance time of the integral
emergency battery.

Air Data Computer (ADC) Failure

Indications
1. Loss of data accompanied by a red X and
yellow alert messages occurs over:
Airspeed
Altitude
Vertical speed
True airspeed (TAS)
Outside air temperature (OAT)
2. Wind calculations are unavailable
Attitude and heading references will function
normally on the PFD.

ADC Failure

Pilot Action
1. Use standby airspeed indicator and altimeter.
There is no backup for the VSI, but known pitch attitudes using
the attitude indicator, power settings, and airspeeds produce
consistent rates.

20 Aircraft Systems

Notable Differences Between 1979-80 & 2000-12 Seminoles

1979-80

2000-12

Left: O-360-E1A6D
Right: LO-360E1A6D

Left: 0-360-A1H6
Right: LO-360-A1H6

4 to 6 Quarts
ATP Minimum 4.5
Quarts

6 to 8 Quarts
ATP Minimum 6.5 Quarts

15 PSI

25 PSI

N/A

Do not use.

Manual/Plunger
Ports Fuel Into
Cylinders 1, 2 & 4

Button/Electric
Electric Fuel Pump Must be On
Press Primer Button 2-3 Sec. before Starting
Cold Engine
Ports Fuel Into Cylinders 1, 2 & 4

N/A

Located on Each Wingtip

Used Instead of Landing Light for Recognition
Saves Landing Light for Night Landing/Takeoff

Anti-Collision Lights
Only (Strobes)

Rocker Switch Down for Ground Use

(Fin Strobe / Rotating Beacon)
Rocker Switch Up Before Takeoff / Flight Use
(Strobes)

LO BUS
Annunciator Light

N/A

Illuminates Red when Alternators not Providing

14 V DC to the tie bus, and bus voltage drops to
battery voltage, 12 V DC

Unfeathering
Accumulators

N/A

Stores Engine Oil Under Pressure for AirStarting the Engine

Releases Stored Pressure Back to Prop Governor
when Prop Lever Moved Forward
Oil Pressure Drives the Blades from the
Feathered Position Toward Low-Pitch
(Windmilling)
Windmilling Prop with Addition of Fuel and
Ignition will Allow the Engine to Start

Starter Only
Be Sure to Only
Engage the Proper
Side of the Rocker
Start Switch
Pressing the Wrong
Side will Cause Engine
Damage to the
Operating Engine

Unfeathering Accumulator

Engines

Oil Capacity

Minimum Oil
Pressure
Landing Gear Mute
Switch
Primer

Recognition Lights

Fin Strobe &

Strobe Light
Rocker Switch

Airstart

The 2000 Seminole utilizes a prop unfeathering

accumulator which stores engine oil under
pressure for airstarting the engine. The stored
pressure is released back to the prop governor
when the prop lever is moved forward. Oil
pressure drives the blades from the feathered
position toward low-pitch windmilling. When
the prop is windmilling, the addition of fuel and
ignition will allow the engine to start.

Aircraft Systems 21

SECTION 3

Performance / Weight & Balance

Piper Seminole V-Speeds

Speeds listed below are in Knots Indicated Airspeed (KIAS).
V-Speed

KIAS

Description

Airspeed
Indicator Marking
Bottom of White Arc

VSO

55

Stall speed in landing configuration

VMC

56

Minimum controllable airspeed

VS

57

Stall speed with zero flaps

VR

75

Rotation speed (start rotation)

VX

82

Best angle of climb

VXSE

82

Best angle of climb single-engine

VSSE

82

Safe speed for intentional engine failure

VY

88

Best rate of climb

VYSE

88

Best rate of climb single-engine

Blue Line

VFE

111

Maximum flap extension speed

Top of White Arc

VLO (Up)

109

Maximum gear retraction speed

VLO (Down)

140

Maximum gear extension speed

VLE

140

Maximum speed with gear extended

VNO

169

Max Structural Cruising Speed

VNE

202

Never exceed speed

VA

135

Maneuvering speed at 3800 pounds

VA

112

Maneuvering speed at 2700 pounds

Maximum demonstrated crosswind 17

22 Performance / Weight & Balance

Red Line
Bottom of Green Arc

Top of Green Arc

Red Line

Performance Charts
All performance charts will be covered by the instructor and are not limited to
the following:

Takeoff Distance to Clear a 50' Obstacle

Accelerate Stop Distance (Piper does not provide an Accelerate Stop
Distance chart for 2000/2001 models.)
Single Engine Rate of Climb
Single Engine Service Ceiling
Landing Distance

Sample Weight & Balance Problem

Complete the following sample weight and balance problem.

Conditions
Basic Empty Weight:............................................................................... 2,540.5 lbs.
(Remember to use actual aircraft BEW for flight check.)

Front Pilots:........................................................................................................370 lbs.

Rear Passengers:...............................................................................................170 lbs.
Baggage:................................................. 3 Bags @ 75 lbs. and 2 Bags @ 50 lbs.
(May need to relocate some baggage to rear passenger seats.)

Max Ramp Weight:...................................................................................... 3,816 lbs.

Max Takeoff/Landing Weight:................................................................. 3,800 lbs.
Max Baggage Weight:....................................................................................200 lbs.
Max Usable Fuel:............................................................................................. 108 gal.
Weight

Arm

Moment

86.13

Basic Empty Weight

Front Pilots +

80.50

Rear Passengers +

118.10

142.80

Baggage 200 lbs. Max

Zero Fuel Weight =

CG =
CG = Moment / Weight

Usable Fuel +

95.00

Ramp Weight =
Taxi Fuel (2.65 Gal.)

Takeoff Weight =

16 95.00

1,520
CG =

CG = Moment / Weight

Fuel Burn

Landing Weight =

CG
CG = Moment / Weight

Performance / Weight & Balance 23

Calculate the Following

1.
2.
3.
4.
5.

Zero Fuel CG
Usable Fuel
Takeoff Weight
Takeoff CG
From comparing the Takeoff CG and Zero Fuel CG, which direction does
the CG move as fuel is burned off?

Plot Zero Fuel CG and Takeoff CG on the CG Envelope Graph Below

Answers:

(1) 91.6

(2) 68.4 gal.

(3) 3,800 lbs.

(4) 91.9

(5) Forward

Formulas

Weight Arm = Moment

Total Moment Total Weight = CG
Max Ramp Weight Zero Fuel Weight = Usable Fuel Weight
Fuel Weight 6 = Fuel Gallons
100 LL (Blue) Fuel Weighs 6 lbs./gal.; Oil Weighs 7.5 lbs./gal.
2 Gallons of unusable fuel and oil at full capacity are Included in Basic
Empty Weight

CG Envelope Graph

24 Performance / Weight & Balance

SECTION 4

Flight Check Tasks & Procedures

Passenger Briefing
1. Safety Belt/Harness Usage
2. Cockpit Door Operation
3. Emergency Exit Operation

4. Fire Extinguisher Location/Usage

5. No Smoking
6. PIC Authority/Training/Checkride

Pre-Takeoff Briefing (Standard Procedures)

Engine failure or abnormality prior to rotation:

Abort takeoff - Throttles immediately closed

Brake as required - Stop straight ahead

If not enough runway to stop:

Mixture to cutoff
Fuel selectors, Magnetos, & Battery Master Off
Maintain directional control, avoid obstacles

Engine failure after rotation with gear down & sufficient runway remains for a
complete stop:

Maintain directional control

Throttles immediately closed
Land straight ahead, brake as required

Engine failure after rotation with gear up and decision made to continue:

Maintain directional control/Pitch Attitude/Airspeed

Mixtures, Props, Throttles Full Forward
Flaps and Gear Up
Identify with dead foot, Verify by closing the throttle
Feather Prop
Mixture to cutoff
Climb at 88 KIAS/Blueline
Declare an Emergency and Land

Flight Check Tasks & Procedures 25

Normal Takeoff (Flaps 0)

Do not delay on runway.
1.
2.
3.
4.
5.

Increase throttles to 2000 RPM.

Check engine gauges.
Increase throttles to full power.
Airspeed Alive.
Start slow rotation at 75 KIAS.

(Main gear should lift off at approximately 80 KIAS. 75 KIAS is VR, not VLOF.)

6. Accelerate to 88 KIAS/Blueline (VY).

7. Establish a positive rate of climb and retract the gear if no runway
remains.
(When taking off from runways 4,000' or less, no runway usually
remains after a positive rate of climb has been established.)
8. Climb at 88 KIAS/Blueline (VY) until 500' AGL.
9. Climb at 110 KIAS after passing through 500' AGL.
(100-110 KIAS provides better visibility and engine cooling. Density
altitude, terrain, obstacles, etc. may require a climb speed from 82-100
KIAS.)
10. Reduce throttles to 24" MP, 2500 RPM at 1,000' AGL.
11. After Takeoff Checklist out of 1,000' AGL.

Normal Takeoff Profile

After Takeoff Checklist

Airspeed
Alive

Positive RateGear Up

Some ATP aircraft are equipped with Traffic Information System

(TIS). TIS is not intended to be used as a collision avoidance
system and does not relieve the pilot of responsibility to see and
avoid other aircraft.

26 Flight Check Tasks & Procedures

Engine Failure Procedure

After Takeoff with No Runway Remaining and Gear Up
Should an engine failure occur after takeoff and gear-up in a light twin, the
following three second, step-by-step technique is suggested. For liability
purposes, the following procedure does not cover all situations due to aircraft
weight, OAT, density altitude, and aircraft performance. Refer to aircraft POH for
additional information.
Engine Failure Occurs Perform the following in 3 seconds.
One Thousand One: Decrease pitch attitude to horizon or slightly above
approximately 1 on AI. (If the Seminole is trimmed flying out at 88 KIAS and
engine failure occurs, the airplane nose will drop towards the horizon due to
loss of lift.)
One Thousand Two: Input aileron to bank 2 to 5 into the operating engine. This
will assist in directional control and assist in stopping the torque roll effect.
One Thousand Three: Input rudder towards the operating engine. Inputting the
rudder after accomplishing the above steps in the first two seconds will help
alleviate stomping on the wrong rudder, creating a situation of directional
control loss, airspeed loss, and possible altitude loss. Immediately accomplish
memory items on In-Flight Engine Failure checklist.

In-Flight Engine Failure

(After Takeoff)

EMERGENCY

(For ATP, Inc. training and checkrides only perform Troubleshoot

Checklist at or above 3000' AGL. If an actual engine failure occurs,
perform Troubleshoot Checklist only if altitude permits.)

MAINTAIN DIRECTIONAL CONTROL / PITCH

ATTITUDE / AIRSPEED
MIXTURES....................................... FULL FORWARD
PROPS.............................................. FULL FORWARD
THROTTLES..................................... FULL FORWARD
FLAPS .....................................................................UP
GEAR.......................................................................UP
IDENTIFY ................................................ DEAD FOOT
VERIFY/THROTTLE.......................................... CLOSE
PROP INOP ENG ......................................... FEATHER
MIXTURE INOP ENG ....................................CUTOFF
CLIMB* ........................................ 88 KIAS/BLUELINE
DECLARE AN EMERGENCY WITH ATC
LAND AT NEAREST SUITABLE AIRPORT
*Note:
After Takeoff: Climb at 88 KIAS/Blueline or 82 KIAS/Vxse if
required for obstacle clearance. Climb
to pattern
Flight Check
Tasksaltitude
& Procedures 27
or as required.
In Cruise: Maintain altitude as necessary.

Approach Briefing
IFR

VFR

Field Elevation
Type of Approach
NAV Frequency
Course
Glideslope Intercept or FAF Altitude
Minimums
Missed Approach Procedure

Field Elevation
Pattern Altitude
Type of Landing
Brief 400' AGL altitude for
"Gear DownStabilized" call

Announced Calls on Approach

Gear Down Before Landing Checklist.
Visual: Prior to descending from Traffic Pattern Altitude (TPA)
(abeam approach end on downwind).

ILS: dot below glideslope intercept.

Non-Precision: At or just prior to FAF.

BluelineGUMP. Gas, Undercarriage, Mixtures, Props.

Visual: On base or turning final.
Instrument: Descending through 1,000' AGL.
The GUMP check is a backup before landing checklist that must
be demonstrated to ensure pilots are familiar with its use when
flying light complex aircraft.

Gear DownStabilized.
Visual or ILS: At 400' AGL.
Non-Precision: Descending from MDA.
100 To Go.
Instrument: Prior to MDA or DH.
Minimums.
Instrument: at MDA or DH.

Stabilized Approach Corridor

The stabilized approach corridor is required during visual and instrument
approaches in ATP aircraft. The aircraft must be stabilized by:
1,000' AGL for an ILS Approach.
Descending from MDA for a Non-Precision Approach.
500' AGL for a Visual Approach.
A Gear DownStabilized call and verification are required for all approaches at
400' AGL or when descending from MDA.
28 Flight Check Tasks & Procedures

General Conditions for a Stabilized Approach

Aircraft in landing configuration. (Gear down and final flaps set.)

Engines must be steady at the proper approach power setting.
Proper descent angle and rate of descent must be established and
maintained. All available landing aids (ILS, VASI, PAPI, etc.) must be
used. Non-precision approaches may require a slightly steeper angle
until reaching MDA.
Airspeed must be stable and within range of target speed plus 10 KIAS.
The aircraft will touch down in the first 1,000' of the landing runway. If
this is not assured, a go-around must be executed.

Conditions for a Seminole Stabilized Approach (Normal & Single-Engine)

Gear Down, Flaps 25.

Power Set Approx. 15" MP (2-engine) or 20" MP (1-engine).
Approx. 500 FPM Descent.
Airspeed 88 KIAS at 400' AGL or Descending from MDA.
Gear DownStabilized Announced & Verified.

The procedures and parameters listed above are not merely targets, they are
mandatory conditions and limits. Any deviation occurring at or beyond the
beginning of the stabilized approach corridor requires a mandatory go-around.
A go-around must be accomplished if at 400' AGL the aircraft is not stabilized
with gear down.

Go Around Philosophy
The decision to execute a go-around is both prudent and encouraged anytime
the outcome of an approach or landing becomes uncertain. ATP considers the
use of a go-around under such conditions as an indication of good judgement
and cockpit discipline on the part of the pilot.

Normal Landing

Verify and announce at 400' AGL: Gear DownStabilized.

Maintain a stabilized descent angle.
Reduce throttles slowly over approach end, slow to 80 KIAS
Touch down at approx. 75 KIAS on centerline within the first 1,000' of
the runway.
Maintain back pressure on control wheel to prevent slamming the nose
wheel onto the runway.

Flap Setting
ATP always recommends landing with flaps 25. The approach speeds used
for flaps 25 are the same as flaps 40 for normal landings. Flaps 25 places
Flight Check Tasks & Procedures 29

the airplane in the best configuration for go-arounds and crosswind landings.
Note: Flaps 25 also introduces a secondary gear warning. Use pilot discretion
for situations requiring a different setting, such as short field landings, singleengine maneuvering or high winds. The revised PA-44-180 operation manual,
section 4.31a states: landing may be made with any flap setting.
The gear horn is an action horn. The gear warning horn should
never be heard below 1,000' AGL on arrivals. Take immediate
action by extending the landing gear or by going around.

Normal Visual Approach & Landing

1. Complete the Approach Checklist before entering the traffic pattern;
devote full attention to aircraft control and traffic avoidance.
2. Slow to 100 KIAS prior to entering downwind or traffic pattern.
3. Enter traffic pattern at published TPA (typically 1,000' AGL).
4. Announce when abeam approach end, on extended base, or on
extended final (When ready to descend out of pattern altitude):
Gear Down Before Landing Checklist.
5. Extend flaps 25.
6. Descend out of TPA at 88 KIAS/Blueline.
7. Announce on base leg or turning final: BluelineGUMP.
Gas, Undercarriage, Mixtures, Props.
8. Maintain 88 KIAS/Blueline with flaps 25 on base and final.
9. Announce at 400' AGL: Gear DownStabilized.
Whenever leaving TPA you should verify that the Gear Down
Before Landing Checklist has been accomplished.

Gear Down Before Landing Checklist

(ATP, Inc. Max Gear Speed 120 KIAS)

GEAR............... (Hand on Selector Until) 3 GREEN

FUEL SELECTORS............................ON
FLAPS ................................. (Vfe 111 KIAS) 25
MIXTURES..................................... FWD
PROPS............................................ FWD
FUEL PUMPS....................................ON
Checklist Complete

Gear&Down
Before Landing Checklist
30 Flight Check Tasks
Procedures

Short Field
GEAR............................. (Hand on Selector Until) 3 GREEN

90

On Base
Maintain Blueline Speed
Check and Announce: Blueline GUMP,
Gas, Undercarriage, Mixtures, Props

At 200' AGL
Begin Slowing On Final
At 400' AGL Check and Announce:
to 80 KIAS
Gear Down Stabilized
(Gear Down, Flaps 25, Power Stable,
Approx 500 FPM Descent, Blueline)
45

88 KIAS

Approx. 15 Mi from Airport

Approach Check
Verify 400' AGL Alt. for Gear Down Stabilized call

When Ready to Descend Out of Pattern Altitude

(Only descend out of pattern altitude on one engine
when certain of making the runway.)
Announce: Gear Down Before Landing Checklist
Extend Gear (Hand On Selector Until 3 Green)
S
Set Flaps 25
Approx.
5
Mi
from
Airport
A
Accomplish Before Landing Checklist
KI
Reduce Power to Approx. 15" MP,
0
or Power Setting that Eliminates Gear Horn
0
1
Maintain 100 KIAS and Pattern Altitude
Approx. 10 Mi from Airport
Begin Slowing to 100 KIAS
Begin Descent to Reach Pattern Altitude by 5 Mi Out

Maintain Centerline Until Taxi Speed

Touchdown on first third of RWY

at Approx 75 KIAS

Normal Visual Approach & Landing Profile

Flight Check Tasks & Procedures 31

VIDEO: Visit ATPFlightSchool.com/students to watch an ILS

approach, non-precision approach, and missed approach using
ATP procedures.
e-learning

ILS Approach One or Two Engines

ATP recommends initially setting flaps 25 at glideslope intercept for both one
and two-engine ILS precision approaches. When conducting a one-engine ILS
down to minimums it is assumed that a landing is assured. Flaps 25 allows for a
stabilized approach to touchdown for both one and two-engine operations. ATP
does not recommend a one-engine go around below 400' AGL.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.

Complete the Approach Checklist and identify localizer when able.

Set the published inbound course on the HSI.
The aircraft is considered established inbound when the course is alive.
Check for flags at glideslope intercept altitude and marker.
Maintain 100 KIAS until glideslope intercept.
dot below glideslope intercept: Gear Down Before Landing Checklist.
Extend flaps 25.
Descend on glideslope at 88 KIAS/Blueline (or 100 KIAS considering
traffic).
Announce out of 1,000' AGL: BluelineGUMP.
Gas, Undercarriage, Mixtures, Props.
Maintain 88 KIAS/Blueline from 1,000' AGL inbound.
Announce at 400' AGL: Gear DownStabilized.
Announce at 100' above minimums: 100 To Go.
Minimums.

ILS Approach One or Two Engines Profile

Gear Down Before Landing ChecklistFlaps 25
Blueline, GUMP.
Gear DownStabilized
100 to go
Minimums

32 Flight Check Tasks & Procedures

Non-Precision Straight-In Approach One or Two Engines

For simulated single-engine non-precision straight-in approach: Gear Down

Before Landing Checklist at FAF; maintain 100 KIAS approach speed and flaps
0; Flaps 25 descending from MDA, followed by the Gear DownStabilized
call. If the airplane will not maintain MDA on a simulated one-engine approach
with full power on the operating engine, terminate the approach and use both
engines.
During simulated single-engine training ATP prohibits
gear retraction at MDA unless a missed approach is being
demonstrated. With an actual engine failure, you may be
required to retract the gear to maintain MDA.

1. Complete the Approach Checklist and identify the NAV aid when able.
2. Maintain 100 KIAS clean (gear up, flaps up) during procedure turn
outbound and inbound to the FAF.
3. Set the published inbound course on the HSI.
4. The aircraft is considered established inbound when the course is alive.
5. Check for flags.

6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.

Note: On two-engine non-precision approaches it is recommended that the Gear

Down Before Landing Checklist is accomplished while inbound just prior (approx.
2 miles) to the FAF. Single-engine non-precision approaches require the gear to be
extended no earlier than the FAF due to the drag introduced.

At FAF: Start time, Gear Down Before Landing Checklist.

Flaps 0 (one engine) Flaps 25 (two engines).
Descend at 88-100 KIAS.
Descend at 600-800 FPM at 88 KIAS/Blueline.
Announce out of 1,000' AGL: BluelineGUMP.
Gas, Undercarriage, Mixtures, Props.
Maintain 88 KIAS/Blueline from 1,000 AGL inbound.
Announce at 100' above minimums: 100 To Go.
Minimums.
Maintain MDA (plus 50' minus 0').
Runway in sight: descend at predetermined VDP or maintain MDA to
MAP.
Do not leave MDA until landing is assured.
When descending from MDA:
Flaps 25 (single-engine), verify and announce: Gear DownStabilized.

Non-Precision Straight-In Approach One or Two Engines Profile

Gear Down Before Landing Checklist
Blueline, GUMP.
100 to go
Minimums
Gear DownStabilized

Flight Check Tasks & Procedures 33

Circle to Land Approaches Two Engines

ATP prohibits engine-out (actual or simulated) circle to land
approaches in the training environment.

ATP requires 88 to 100 KIAS approach speed and flaps 0 for circle to land
approaches. Unlike straight-in approaches, maintain 88 to 100 KIAS out of 1,000'
AGL, descending to MDA. Approach category B is used for minimums. Category
B speed ranges from 91 KIAS to 120 KIAS. When leaving MDA, set flaps 25 and
verify and announce Gear DownStabilized. Do not exceed 111 KIAS (VFE)
during approach.
1. Complete the approach checklist and identify the NAV aid when able.
2. Maintain 100 KIAS clean (gear up, flaps up) during procedure turn
outbound and inbound to the FAF.
3. Set the published inbound course on the HSI.
4. The aircraft is considered established inbound when the course is alive.
5. Check for flags.
6. At FAF: Start time, Gear Down Before Landing Checklist.
7. Flaps 0.
8. Descend at 88-100 KIAS.
9. Descend at 600-800 FPM at 88-100 KIAS.
10. Announce out of 1,000' AGL: BluelineGUMP.
Gas, Undercarriage, Mixtures, Props.
11.
12.
13.
14.

(You may maintain up to 100 KIAS for circle maneuver at MDA.)

Announce at 100 above minimums: 100 To Go.

Minimums.
Maintain MDA during circling maneuver (plus 50' minus 0').
When turning onto final and descending from MDA:
Flaps 25, verify and announce: Gear DownStabilized.

Circle to Land Approaches Two Engines Profile

Gear Down Before Landing Checklist

Blueline, GUMP.
100 to go
Minimums

Gear DownStabilized

34 Flight Check Tasks & Procedures

Go Around / Missed Approach

1. Simultaneously increase throttles to full power and pitch for climb.
2. Retract flaps slowly to 0.
(Slowly to preclude excessive sink.)

3. Retract landing gear upon acquiring positive rate of climb.

4. Climb at 88 KIAS/Blueline (VY) until 500' AGL.
5. Climb at 110 KIAS after passing through 500' AGL (provides better
visibility and engine cooling) unless VX or VY is needed for obstacle
clearance.
6. Reduce power to 24" MP, 2500 RPM at 1,000' AGL.
7. Announce and perform After Takeoff Checklist out of 1,000' AGL.

Holding
Max speeds:
Up to 6,000' MSL........................... 200 KIAS
6,001' to 14,000' MSL................... 230 KIAS
1.
2.
3.
4.
5.

Slow to 100 KIAS holding speed 3 minutes prior to fix.

Acquire EFC.
Hold at 100 KIAS, with 1 minute leg to the inbound fix once established.
Report altitude and time at holding fix.
Make proper entry.

Approach, Procedure Turn & Holding Power Settings

The following suggested power settings are approximations only.
Speed

2-Eng.

1-Eng.

ILS

88 KIAS (Configured)

15"

20"

Non-Precision

88 KIAS (Configured)

13"

15" (600-800 FPM Descent)

Level at MDA

88 KIAS (Configured)

20"

Full or As Necessary

Holding/PT

100 KIAS (Clean)

18"

Full or As Necessary

Traffic Pattern

100 KIAS (Clean)

18"

Full or As Necessary

In-Flight Maneuvers
The following maneuvers (except for the VMC Demo unless CLT restricted) are
required for all ratings. Additional procedures required for the specific rating
sought are listed in the following sections for Airline Transport Pilot, Commercial
Multi-Engine Add-On, CFI Multi-Engine Add-On and Private Multi-Engine AddOn.

Flight Check Tasks & Procedures 35

Clearing Turns for In-Flight Maneuvers

1.
2.
3.
4.

Maintain selected altitude.

Set bug to entry heading.
Perform 90 clearing turn to left or right.
Reduce power to approximately 15" MP, as specified for the maneuver,
or just above the gear horn sounding to slow airplane. (A higher MP
setting may be required so the gear horn will not sound during the
clearing turn.)
5. Perform 90 clearing turn back to original heading.
When slowing for maneuvers or approaches, maintain a power
setting that eliminates the gear horn. This may increase the
target speed to maintain gear horn silence.

VMC Demonstration

Not required for ATP rating, unless CLT restricted. The VMC Demo is to be
accomplished at or above 4,000' AGL, or as specified by Examiner.
In the Piper Seminole, VMC occurs at a lower airspeed than stall speed. The
Seminole will lose power as altitude increases because of the reduced density
of the air entering the induction system of the engine. Increase the pitch
attitude slowly to reduce the airspeed at approximately 1 knot per second
while applying rudder pressure to maintain directional control until full rudder
is applied. As the speed decreases, additional aileron input will be required to
maintain a maximum of 5 bank toward the operating engine. Recover at the
first indication of loss of directional control, stall horn, or buffet.
1.
2.
3.
4.
5.
6.

Clearing turns.
Flaps-up, gear-up.
MixturesEnrichen, PropsFwd, Fuel PumpsOn.
Slowly close left throttle while maintaining heading and altitude.
Slow to 100 KIAS (approx. 10 KIAS above VYSE).
Slowly increase right throttle (operating engine) to full power. Use
rudder to maintain directional control and bank up to 5 towards the
operating engine.
7. Increase pitch attitude slowly, decrease airspeed at approximately 1
knot per second until full rudder is applied to maintain directional
control.
8. Recover at first sign of:
A. Loss of directional control.
B. First indication of stall (stall horn or buffet).
9. Recover promptly by simultaneously reducing power sufficiently on the
operating engine while decreasing the angle of attack as necessary to
regain directional control within 20 of entry heading.
36 Flight Check Tasks & Procedures

10. Continue recovery by increasing power slowly on operating engine

while maintaining an AOA that allows for airspeed to increase to a point
where directional control can be maintained with a minimum loss of
altitude.
11. Accelerate to 82-88 KIAS.
12. Bring throttles slowly together to 20" MP.
13. Cruise Checklist.
Recovery shall not be attempted by increasing the power on the simulated
failed engine for demonstration.
During the VMC Demo, the gear horn will sound due to the left
throttle being closed. Do not confuse the gear horn, which beeps
at 90 cycles per minute, with the steady stall warning horn
typically the first indication of a stall at which to begin recovery.

Maneuvering with One Engine Inoperative

The maneuver shall be performed above 4,000' AGL and in a position where a
safe landing at an airport can be accomplished in the event the engine cannot
be restarted. Maintain altitude 100' unless a minimum sink is required due to
airspeed at blueline and extremely high density altitude. Maintain heading 10.
Below 3,000' AGL, engine failures may be simulated with the
throttle only. At 3,000' AGL or higher, engine failures may also
be simulated with the mixture. Never use the fuel selector to
simulate an engine failure.

In-Flight Engine Failure (Shutdown-Secure) Demo

1. Instructor or examiner simulates engine failure with the mixture.
2. Complete the In-Flight Engine Failure Checklist.
3. Complete the Troubleshoot Checklist above 3,000' AGL (if no obvious
damage).
4. If no re-start, continue the In-Flight Engine Failure Checklist and
complete the Engine Failure Secure Checklist.
5. Maneuver as specified by instructor or examiner.
When maneuvering with one engine inoperative is complete, perform an
airstart (separate maneuver) using the Airstart Checklist.

Flight Check Tasks & Procedures 37

Perform an actual engine shutdown on either engine only above

4,000' AGL. When performing the engine shutdown and secure
maneuver as part of a training event (as opposed to an actual
emergency), the items on the Engine Failure Secure Checklist are
to be simulated (touched but not actuated).

In-Flight Engine Failure

EMERGENCY

MAINTAIN DIRECTIONAL CONTROL / PITCH ATTITUDE / AIRSPEED

MIXTURES....................................... FULL FORWARD

PROPS.............................................. FULL FORWARD
THROTTLES..................................... FULL FORWARD
FLAPS .....................................................................UP
GEAR.......................................................................UP
IDENTIFY ................................................ DEAD FOOT
VERIFY/THROTTLE.......................................... CLOSE
Troubleshoot Checklist
THROTTLE ...................................... 1/4
FUEL PUMPS ...................................ON
MAGNETOS ........................ON/CHECK
FUEL SELECTORS ...........................ON
CARB HEAT ............... ON, CHECK, OFF
FUEL QTY/PRESSURE .............. CHECK
OIL PRESSURE/TEMP............... CHECK
(If engine inop continue In-Flight Engine Failure
Checklist & Engine Failure Secure.)

PROP INOP ENG .............................................. FEATHER

MIXTURE INOP ENG .........................................CUTOFF
Engine Failure Secure
OPERATING ENG MIXTURE ......................LEAN AS REQ
TRIM.................................................... AS REQUIRED
INOP ENG MAGNETOS ........................................... OFF
INOP ENG FUEL PUMP ............................................ OFF
INOP ENG ALTERNATOR ......................................... OFF
INOP ENG FUEL SELECTOR .................................... OFF
INOP ENG COWL FLAP .................................... CLOSED
REC/BLOW ............................................................ OFF

38 Flight Check Tasks & Procedures

Example Single-Engine Drift Down Scenario

Inoperative Engine at 8,000' MSL, 20 C, and 3,400 lbs. (This is the approximate
weight for two people, bags, and half fuel.) The following computations are
based on the Climb Performance - One Engine Operating - Gear Up chart in the
Seminole POH.
Associated Conditions: Flaps 0, Operating Engine Cowl Flap Open, Inoperative
Engine Cowl Flap Closed, Landing Gear Up, Mixture Full Rich, Inoperative Engine
Prop Feathered, Full Throttle, 2700 RPM, 88 KIAS/Blueline. (To achieve maximum
single-engine performance, the operating engine mixture should be leaned as
required.)
(Feet MSL)

Altitude

(C) / (F)

Temp

Rate of Climb

Distance at 88 KIAS/Blueline

8,000

20 / 68

-120

From 8,000 to 7,000: 13 NM

7,000

22 / 72

-80

From 7,000 to 6,000: 19 NM

6,000

24 / 75

-40

From 6,000 to 5,000: 37 NM

5,000

26 / 79

Single Engine Absolute Ceiling

4,000

28 / 82

50

Single Engine Service Ceiling

(FPM)

(Approx. 1.5 NM per minute)

All figures are approximate.

Airstart Procedure
The airstart procedure varies between the 1979 and 2000 model Seminoles
since the 2000 models are equipped with an unfeathering accumulator.

1979 Model Seminole

Airstart

Prop Windmilling

INOP ENG STARTER........................................RELEASE

When Engine Begins to Run

THROTTLE .............. INCREASE SLOWLY TO 15" MP
MAINTAIN 15" MP UNTIL CHT GREEN
AVIONICS MASTER .............................................. ON
PERFORM CRUISE CHECKLIST (Next Page)

EMERGENCY

INOP ENG FUEL SELECTOR ..................................... ON

INOP ENG CARB HEAT ............................................ OFF
INOP ENG MIXTURE ........................... FULL FORWARD
INOP ENG PROP .................................. FULL FORWARD
INOP ENG FUEL PUMP ............................................. ON
INOP ENG ALTERNATOR .......................................... ON
INOP ENG MAGNETOS ............................................ ON
AVIONICS MASTER ................. (If Conditions Permit) OFF
INOP ENG THROTTLE .................TWO FULL STROKES
INOP ENG THROTTLE ....................................1/4" OPEN
INOP ENG STARTER............. (ATP 8 Seconds Max) ENGAGE

Flight Check Tasks & Procedures 39

Prop Overspeed
THROTTLE .....................................................RETARD

2000 Model Seminole

Airstart

(The prop may not easily come out of feather unless airspeed is at least
100 KIAS. It may take up to 20 seconds for prop to windmill.
If prop does not windmill verify that there is no prop movement,
then engage starter for 2 seconds.)

When Engine Begins to Run

THROTTLE .............. INCREASE SLOWLY TO 15" MP
MAINTAIN 15" MP UNTIL CHT GREEN
PERFORM CRUISE CHECKLIST

EMERGENCY

INOP ENG THROTTLE ...................................... CLOSED

INOP ENG FUEL SELECTOR ..................................... ON
INOP ENG CARB HEAT ............................................ OFF
INOP ENG MAGNETOS ............................................ ON
INOP ENG FUEL PUMP ............................................. ON
INOP ENG ALTERNATOR .......................................... ON
INOP ENG MIXTURE ........................... FULL FORWARD
INOP ENG PROP .................................. FULL FORWARD
AIRSPEED .................................... (Suggested) 120 KIAS
INOP ENG THROTTLE ....................................1/4" OPEN

Emergency Descent

Prop Overspeed
Prop Overspeed
(AFM p. 3-19)
ThrottlesSlowly
reduce to idle.
THROTTLE .....................................................RETARD
PropsFull
Forward.
OIL PRESSURE................................................CHECK
MixturesAdjust.
PROP CONTROL.......................................DECREASE
not feather.
if any
control.)
GearDown, (Do
accelerate
upSet
toRPM
a max
speed
of 140 KIAS (For training at
AIRSPEED
.....................................................
REDUCE
ATP use 120 KIAS unless specified by examiner to
go up to the max of
THROTTLE (Below 2700 RPM) ............................. AS REQ
140
KIAS.)
ENG SHUTDOWN ............................. IF NECESSARY
5. Cowl
FlapsAs
29 2000
Model Required.
6. Maintain 140 KIAS (ATP 120 KIAS) during descent.
7. Notify ATC as appropriate.

1.
2.
3.
4.

When recovering from the Emergency Descent, verify airspeed

at or below 109 KIAS (maximum gear retraction speed) before
retracting the gear.

Recovery from Unusual Attitudes

Nose HighClimbing

Nose LowDescending

(Airspeed Decreasing)

(Airspeed Increasing)

1.
2.
3.
4.

Increase power.
Pitch level.
Bank 0.
Cruise Checklist.

40 Flight Check Tasks & Procedures

1.
2.
3.
4.

Reduce power.
Bank 0.
Pitch smoothly level.
Cruise Checklist.

Spin Awareness
Aerodynamic Factors

All spins are preceded by a stall on at least part of the wing. The primary cause
of an inadvertent spin is exceeding the critical AOA while applying excessive or
insufficient rudder and, to a lesser extent, aileron. Asymmetrical power could
contribute to a spin.

Flight Situations when Unintentional Spins may Occur

During a VMC Demonstration, when at the point of reaching both VMC

and stall simultaneously.
It may also occur while maneuvering during slow flight.

Procedure for Recovery from Unintentional Spins

This procedure is taken directly from the Piper Seminole POH.

1.
2.
3.
4.
5.
6.
7.

ThrottlesRetard to idle.
RudderFull opposite to direction of spin.
Control WheelRelease back pressure.
Control WheelFull forward if nose does not drop.
AileronsNeutral.
RudderNeutralize when rotation stops.
Control WheelSmooth back pressure to recover from dive.
Intentional spins are prohibited in multi-engine aircraft. For
further reference concerning stall and spin awareness, consult
AC 61-67C.

Flight Check Tasks & Procedures 41

SECTION 5

Private Pilot Multi-Engine Add-On

Specific Tasks & Procedures

Steep Turns
Steep turns are to be accomplished above 3,000' AGL. Roll into a coordinated
360 steep turn with at least 45 of bank. The applicant is required to maintain
entry altitude 100', airspeed 10 KIAS, and bank angle 5, roll out on the entry
heading 10.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Clearing turns as specified by the Examiner.

Set power 20" MP, 2300 RPM.
Set bug to entry heading.
Maintain selected altitude 100'.
Maintain 120 KIAS or a safe airspeed not to exceed VA.
Adjust power as necessary during maneuver.
Perform 360 turn to the left maintaining at least 45 bank 5.
Roll out on entry heading 10.
Perform 360 turn to the right maintaining at least 45 bank 5.
Roll out on entry heading 10.

Maneuvering During Slow Flight

Slow flight is to be accomplished above 4,000' AGL. As specified by the
Examiner, this maneuver may be accomplished in any configuration while
demonstrating coordinated straight-and-level flight, climbs, turns, and descents.
The airspeed selected is that at which any further increase in angle of attack,
increase in load factor, or reduction in power would result in an immediate stall.
The applicant is required to maintain selected altitude 100', heading 10,
airspeed +10/-0 KIAS, and bank angle 10.
1.
2.
3.
4.
5.

Clearing turns.
Gear Down Before Landing Checklist.
Extend full flaps 40.
Slow to just above stall (approximately 60 KIAS).
Adjust power as necessary (approximately 20" MP) to maintain airspeed
while maneuvering.
6. Accomplish straight-and-level flight, climbs, turns, and descents as
required.
42 Private Pilot Multi-Engine Add-On

7. Recover with max power.

8. Retract flaps slowly to 0.
9. Accelerate to 82 KIAS (VX), maintain altitude or climb as specified by
Examiner.
10. Retract gear, accelerate to 88 KIAS (VY).
11. Cruise Checklist.

Stall Recovery
When practicing recovery from a fully developed stall in a multi-engine aircraft,
immediately reduce the AOA by aggressively moving the elevator control
forward to ensure recovery without worrying about a specific loss of altitude.
This is not an approach to stallit is a stall that has broken and an aggressive
reduction in AOA is critical. The PTS places no emphasis on maintaining altitude
or limiting loss of altitude.
CAUTION: Fully developed stalls may lead to inadvertent,
unrecoverable spins.
Stall training (in multi-engine airplanes) should be limited
to approaches to stalls and when a stall condition occurs.
Recoveries should be initiated at the onset, or decay of control
effectiveness, or when the first physical indication of the stall
occurs. (AFH 12-26)
No multi-engine airplane is approved for spins, and spin
recovery characteristics are generally very poor. It is therefore
necessary to practice spin avoidance and maintain high
awareness of situations that can result in an inadvertent spin.
(AFH 12-27)
Fully developed stalls in a multi-engine airplane is a situation
that can result in an inadvertent spin.
In order to spin any airplane, it must first be stalled. At the
stall, a yawing moment must be introduced. In a multi-engine
airplane, the yawing moment may be generated by rudder input
or asymmetrical thrust. (AFH 12-27)
When recovering with max power, advance throttles smoothly.
This assists with symmetrical power increases.

Private Pilot Multi-Engine Add-On 43

Power-Off Stall
Stalls are to be accomplished above 4,000' AGL, with a stabilized descent
approximating a 3 final approach glidepath (400 FPM). Private requires prompt
recovery after a fully developed stall occurs. As specified by the Examiner, this
stall may be accomplished on a selected heading 10 or in a 15-bank turn
(max bank 20).
Always reduce throttles slowly to avoid damage to engines.
When recovering with max power, advance throttles smoothly.
This assists with symmetrical power increases.

1.
2.
3.
4.
5.
6.
7.
8.

9.
10.
11.
12.

Clearing turns.
Gear Down Before Landing Checklist.
Extend full flaps 40.
Establish a stabilized 400 FPM descent at 75 KIAS.
Maintain selected heading, or establish 15-bank turn as specified by
Examiner.
Slowly reduce power to idle.
Slowly increase pitch attitude to induce a stall.
Recover immediately after a fully developed stall occurs.
Simultaneously:
Reduce AOA Lower nose. Do not attempt to maintain altitude.
Smoothly apply max power.
Level wings.
Retract flaps slowly to 0.
Accelerate to 82 KIAS (VX), establish a positive rate of climb.
Retract gear, accelerate to 88 KIAS (VY).
Cruise Checklist.

Power-On Stall
Stalls are to be accomplished above 4,000' AGL. Private requires recovery
after a fully developed stall occurs. As specified by the Examiner, this stall may
be accomplished in the takeoff configuration (Gear Down, Flaps 0) or the
departure configuration (Gear Up, Flaps 0) while on a selected heading 10 or
in a 15-bank turn (max bank 20) 10.
1. Clearing turns.
2. Set takeoff or departure configuration as specified by the Examiner:
A. Takeoff configuration (Gear Down, Flaps 0).
B. Departure configuration (Gear Up, Flaps 0).
3. MixturesEnrichen, PropsFwd, Fuel PumpsOn.
4. Slow to 80 KIAS, liftoff speed.

44 Private Pilot Multi-Engine Add-On

5. Maintain selected heading or establish a 15-bank turn, as specified by

the Examiner.
6. Transition smoothly to approx. 15 pitch-up while increasing power to
18" MP.
7. Recover immediately after a fully developed stall occurs.
Simultaneously:
Reduce AOA Lower nose. Do not attempt to maintain altitude.
Smoothly apply max power.
Level wings.
8. Accelerate to 82 KIAS (VX), establish a positive rate of climb.
9. Retract gear (if extended), accelerate to 88 KIAS (VY).
10. Cruise Checklist.

Private Pilot Multi-Engine Add-On 45

SECTION 6

Commercial Multi-Engine Add-On

Specific Tasks & Procedures

Steep Turns
Steep turns are to be accomplished above 3,000' AGL. Roll into a coordinated
360 steep turn with at least 50 of bank. The applicant is required to maintain
entry altitude 100', airspeed 10 KIAS, and bank angle 5, roll out on the entry
heading 10.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Clearing turns as specified by the Examiner.

Set power 20" MP, 2300 RPM.
Set bug to entry heading.
Maintain selected altitude 100'.
Maintain 120 KIAS or a safe airspeed not to exceed VA.
Adjust power as necessary during maneuver.
Perform 360 turn to the left maintaining at least 50 bank 5.
Roll out on entry heading 10.
Perform 360 turn to the right maintaining at least 50 bank 5.
Roll out on entry heading 10.

Maneuvering During Slow Flight

Slow flight is to be accomplished above 4,000' AGL. As specified by the
Examiner, this maneuver may be accomplished in any configuration while
demonstrating coordinated straight-and-level flight, climbs, turns, and descents.
The airspeed selected is that at which any further increase in angle of attack,
increase in load factor, or reduction in power would result in an immediate
stall. The applicant is required to maintain selected altitude 50', heading 10,
airspeed +5/-0 KIAS, and bank angle 5.
1.
2.
3.
4.
5.

Clearing turns.
Gear Down Before Landing Checklist.
Extend full flaps 40.
Slow to just above stall (approximately 60 KIAS).
Adjust power as necessary (approximately 20" MP) to maintain airspeed
while maneuvering.
6. Accomplish straight-and-level flight, climbs, turns, and descents as
required.
46 Commercial Multi-Engine Add-On

7. Recover with max power.

8. Retract flaps slowly to 0.
9. Accelerate to 82 KIAS (VX), maintain altitude or climb as specified by
Examiner.
10. Retract gear, accelerate to 88 KIAS (VY).
11. Cruise Checklist.

Power-Off Stall
Stalls are to be accomplished above 4,000' AGL, with a stabilized descent
approximating a 3 final approach glidepath (400 FPM). Commercial requires
prompt recovery at the onset (buffeting) stall condition. As specified by the
Examiner, this stall may be accomplished on a selected heading 5 or in a 15bank turn (max bank 20).
Always reduce throttles slowly to avoid damage to engines.
When recovering with max power, advance throttles smoothly.
This assists with symmetrical power increases.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

Clearing turns.
Gear Down Before Landing Checklist.
Extend full flaps 40.
Establish a stabilized 400 FPM descent at 75 KIAS.
Maintain selected heading, or establish 15-bank turn as specified by
Examiner.
Slowly reduce power to idle while increasing pitch attitude to induce
stall (approx. 12).
Recover promptly at the onset (buffeting) stall condition.
Simultaneously reduce angle-of-attack, set max power, and level wings.
Retract flaps slowly to 0.
Accelerate to 82 KIAS (VX), establish a positive rate of climb.
Retract gear, accelerate to 88 KIAS (VY).
Cruise Checklist.

Commercial Multi-Engine Add-On 47

Power-On Stall
Stalls are to be accomplished above 4,000' AGL. Commercial requires recovery
at the onset (buffeting) stall condition. As specified by the Examiner, this stall
may be accomplished in the takeoff configuration (Gear Down, Flaps 0) or the
departure configuration (Gear Up, Flaps 0) while on a selected heading 10 or
in a 15-bank turn (Max bank 20) 10.
1. Clearing turns.
2. Set takeoff or departure configuration as specified by the Examiner:
A. Takeoff configuration (Gear Down, Flaps 0).
B. Departure configuration (Gear Up, Flaps 0).
3. MixturesEnrichen, PropsFwd, Fuel PumpsOn.
4. Slow to 80 KIAS, liftoff speed.
5. Maintain selected heading or establish a 15-bank turn, as specified by
the Examiner.
6. Transition smoothly to approx. 15 pitch-up while increasing power to
18" MP.
7. Recover promptly at the onset (buffeting) stall condition.
8. Simultaneously reduce angle-of-attack, set max power, and level wings.
9. Accelerate to 82 KIAS (VX), establish a positive rate of climb.
10. Retract gear (if extended), accelerate to 88 KIAS (VY).
11. Cruise Checklist.

Accelerated Stall
Accelerated stalls are accomplished at an altitude that allows the maneuver to
be completed no lower than 4,000 feet AGL. Transition smoothly from cruise
attitude to a bank angle of 45, maintaining coordinated turning flight, while
increasing elevator back pressure steadily to induce the stall.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Clearing turns.
Slow to approximately 120 KIAS (during clearing turns).
Flaps-up, gear-up.
MixturesEnrichen, PropsFwd, Fuel PumpsOn.
Establish a coordinated 45 bank turn.
Slowly reduce power to idle.
Maintain altitude to induce stall.
Recover at the onset (buffeting) stall condition.
Simultaneously reduce angle-of-attack, set max power, and level wings.
Cruise Checklist.

48 Commercial Multi-Engine Add-On

Short Field Takeoff & Climb (Flaps 0)

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.

Hold brakes at departure end of runway.

Increase throttles to 2000 RPM.
Check engine gauges.
Increase throttles to full power.
Release brakes.
Airspeed Alive.
Rotate at speed per Short Field Effort Chart (POH section 5) for Flaps 0
and actual weight.
Climb through obstacle height at speed per Short Field Effort Chart
(POH section 5) for Flaps 0 and actual weight.
Establish a positive rate of climb and retract the gear.
Climb at 88 KIAS/Blueline (VY) when clear of obstacles until 500' AGL.
Climb at 110 KIAS after passing through 500' AGL.
Reduce power to 24" MP, 2500 RPM at 1,000' AGL.
After Takeoff Checklist out of 1,000' AGL.

Short Field Takeoff & Climb Profile

After Takeoff Checklist
Positive Rate
Gear Up
Airspeed
Alive

Perform all training flight takeoffs with flaps up. ATP prohibits a
flaps 25 short field takeoff for training and flight checks due to
critically low airspeeds in the event of an actual engine failure.

Commercial Multi-Engine Add-On 49

Short Field Visual Approach & Landing

1. Complete the Approach Checklist before entering the traffic pattern;
devote full attention to aircraft control and traffic avoidance.
2. Slow to 100 KIAS prior to entering downwind or traffic pattern.
3. Enter traffic pattern at published TPA.
4. Announce when abeam approach end, on extended base, or on
extended final (When ready to descend out of pattern altitude):
Gear Down Before Landing Checklist Short Field.
5. Extend flaps 25.
6. Descend out of TPA at 88 KIAS/Blueline.
7. Announce: (On Base Leg or Turning to Final) BluelineGUMP.
Gas, Undercarriage, Mixtures, Props.
8. On final, extend flaps 40.
9. Reduce airspeed to speed per Landing Distance Over 50 Ft. Obstacle
Short Field Effort Chart (POH section 5) for actual weight. Maintain
constant power, airspeed, and angle of descent.
10. Announce at 400' AGL: Gear DownStabilized.
11. Close throttles slowly in the flare touch down with little or no floating.
12. Maintain back pressure on control wheel to prevent slamming the nose
wheel onto the runway.
13. Retract flaps after touchdown.
14. Simulate and announce max braking for training and checkride
purposes.
Use 75 KIAS (max weight speed) on final as a minimum speed for
training and flight checks, unless specified by the Examiner to
use computed speed for actual weight.
Technique: Fly proper speed and maintain some power for round
out, close throttles in flare.

50 Commercial Multi-Engine Add-On

SECTION 7

CFI Multi-Engine Add-On

Specific Tasks & Procedures

Required maneuvers for the CFI Multi-Engine Add-On are the same as
for the Commercial Add-On except for the addition of the Airspeed Drag
Demonstration.

Airspeed Drag Demonstration

Note power required for each drag item and VSI changes throughout each step.
1.
2.
3.
4.
5.
6.
7.
8.
9.

Clearing turns.
MixturesEnrichen, PropsFwd, Fuel PumpsOn.
Slow to 88 KIAS/Blueline.
Extend gear.
Add power to maintain 88 KIAS and altitude.
Extend flaps 25.
Add power to maintain 88 KIAS and altitude.
Extend flaps 40.
Add power to maintain 88 KIAS and altitude.
Above steps are for knowledge of drag to required-power relationships
PTS-Required Tasks Below

10. Close left throttle. (Windmilling prop)

11. Add max power on right engine, maintain 88 KIAS and heading. (Note
VSI.)
12. Left Cowl FlapAs Required.
13. Flaps up, maintain 88 KIAS. (Note VSI.)
14. Gear up, maintain 88 KIAS. (Note VSI.)
15. Left throttle to 12" MP simulated feather power, maintain 88 KIAS. (Note
VSI.)
16. Pitch for 82 KIAS. (Note VSI.)
17. Pitch for 100 KIAS. (Note VSI.)
18. Bring throttles slowly together to 20" MP.
19. Left cowl flap: open or as required.
20. Cruise Checklist.

CFI Multi-Engine Add-On 51

SECTION 8

Airline Transport Pilot

Specific Tasks & Procedures

Steep Turns
Steep turns are to be accomplished above 3,000' AGL and may be performed
with two 180 turns or one 360 turn. Roll into a coordinated 45-bank steep
turn. Roll into and out of turns at approximately the same rate. The applicant
is required to maintain entry altitude 100', airspeed 10 KIAS, and bank angle
5, roll out on the entry heading 10.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

Clearing turns as specified by the Examiner.

Set power 20" MP, 2300 RPM.
Set bug to entry heading.
Maintain selected altitude 100'.
Maintain 120 KIAS or a safe airspeed not to exceed VA.
Adjust power as necessary.
Perform 180 turn to the left maintaining 45 bank 5.
Roll out at 180 point 10.
Perform 180 turn to the right maintaining 45 bank 5.
Roll out on entry heading 10.

Approach to Stall in Approach Configuration (Clean)

Stalls are to be accomplished above 3,000' AGL. ATP rating requires the pilot to
announce the first indication of an impending stall (stall horn). As specified by
the Examiner, this stall may be accomplished on a selected heading 5 or in a
15 to 30-bank turn.
1.
2.
3.
4.
5.
6.
7.
8.
9.

Clearing turns.
Flaps-up, gear-up.
MixturesEnrichen, PropsFwd, Fuel PumpsOn.
Pitch to maintain altitude.
Maintain selected heading, or establish a 20-bank turn as specified by
Examiner.
Announce first indication of impending stall (stall horn).
Initiate recovery using max power or as specified by Examiner.
Recover and maintain selected altitude (and heading if selected).
Cruise Checklist.

52 Airline Transport Pilot

Approach to Stall in Landing Configuration

Stalls are to be accomplished above 3,000' AGL. ATP rating requires the pilot to
announce the first indication of an impending stall (stall horn). As specified by
the Examiner, this stall may be accomplished on a selected heading 5 or in a
15 to 30-bank turn.
Always reduce throttles slowly to avoid damage to engines.
When recovering with max power, advance throttles smoothly.
This assists with symmetrical power increases.

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

Clearing turns.
Gear Down Before Landing Checklist.
Set Flaps 40.
Pitch to maintain altitude.
Maintain selected heading, or establish a 20-bank turn as specified by
Examiner.
Announce first indication of impending stall (stall horn).
Initiate recovery using max power or as specified by Examiner.
Recover and maintain selected altitude (and heading if selected).
Retract flaps slowly to 0.
Accelerate to 82 KIAS (VX).
Retract gear, accelerate to 88 KIAS (VY).
Cruise Checklist.

Airline Transport Pilot 53

SECTION 9

Oral Review

Lost Comm Procedure (FAR 91.185)

If in VFR conditions, or if VFR conditions are encountered, squawk 7600, remain
VFR and land as soon as practicable.
If in IFR conditions, squawk 7600 and Fly:
Route

Altitude

Assigned

Minimum IFR Altitude

Vectored

Expected

Expected

Assigned

(First that applies.)

(Whichever is highest until descent is required

for landing.)

Filed

FAR Review
1. To maintain instrument currency, a pilot must have made six
approaches and demonstrated proper holding procedures as well as
radial and bearing tracking in the last six months.
2. An alternate is not required if the weather at your destination is
forecast to be at least a 2,000' ceiling and visibility of at least three
miles. The forecast must be from one hour before to one hour after
your estimated time of arrival.
3. If an alternate airport is needed, forecasted weather at ETA must be
at least 600' ceiling and 2 miles visibility for a precision approach; an
alternate airport that offers only a non-precision approach must be at
least 800' ceiling and 2 miles visibility. An alternate cannot be based on
a GPS approach.
4. Reserve fuel of 45 minutes is required for IFR flights; 30 minutes for VFR
day flights; and 45 minutes for VFR night flights. This reserve is required
in addition to the fuel required to fly to your destination and alternate.

54 Oral Review

5. VOR limits: 4 degrees for VOT, ground checkpoint and dual check. 6
degrees for an airborne check.
6. VOR equipment must be checked every 30 days.
7. Transponders must be checked every 24 calendar months.
8. Pitot static systems must be checked every 24 calendar months.
9. ELT equipment must be checked every 12 months, after half of the
battery life, or after 1 hour of cumulative use.
10. An aircraft used for hire must have a 100 hour and an annual
inspection.
11. In order to descend below the DH or MDA, all of the following
conditions must exist:
C. The required flight visibility is met.
D. The aircraft is in a normal position to land.
E. (1) The runway environment is in sight descend to land.
(2) Approach lights in sight descend to 100' above touch down
zone until runway environment is in sight.
(3) Descend and land if red terminating bars or red side row bars
are in sight.
12. Multi-engine aircraft with a VSO of 61 knots or less, or a gross weight
under 6,000 pounds do not have to demonstrate positive single-engine
climb performance per FAR 23.
13. The minimum equipment list includes a list of equipment that may
be inoperative for a particular phase of flight. If not required to have a
MEL, comply with the minimum equipment prescribed by the FARs.
14. Standard Traffic Pattern Altitude (TPA) for multi-engine aircraft is 1,000'
AGL.

Answer The Following Sample Oral Questions Prior To Arriving For Training
1. Recite the V speeds.
2. What is the maximum demonstrated crosswind component?
3. Describe the Seminole PA-44-180 engine.
A. How many cylinders?
B. Who is the manufacturer?
C. What is the horsepower rating?
D. Does it have fuel injectors or a carburetor?
E. Is the engine turbo-charged or normally aspirated?
F. Why is the right engine labeled LO-360?
G. How are the cylinders arranged?

Oral Review 55

H. How is ignition provided?

I. What are the minimum and maximum oil capacities in the 1979
and 2000 model Seminoles?
4. Describe the propeller system.
A. Who makes the propellers?
B. What does oil pressure do to the propeller?
C. Which lever manipulates oil pressure to the propeller?
D. Which unit regulates oil pressure to the propeller?
E. What is the function of the nitrogen cylinder?
F. What is the purpose of the spring in the prop dome?
G. Define constant speed.
H. What unit adjusts the propeller to maintain a constant RPM and
how does it do it?
I. Define full feathering.
J. Will the propeller always feather?
K. What are centrifugal stop pins?
L. What is the true purpose of the centrifugal stop pins?
5. What is the correct action for a propeller overspeed?
6. Describe the electrical system.
7. What are the indications of a failed alternator?
8. Will the engines continue to run with the alternator and battery master
switches turned off?
9. Describe the vacuum system.
A. Which instruments are vacuum operated?
B. What are the normal vacuum operating limits?
C. How many vacuum pumps does the PA-44 have?
D. What indications would occur in the event of a vacuum pump
failure?
10. Describe the stall warning system.
11. Describe the fuel system.
12. Explain how to cross feed fuel.
13. Describe the landing gear system.
A. How is the landing gear actuated? Describe the pump.
B. What keeps the gear in the up position?
C. What keeps the gear in the down position?
D. If Hydraulic pressure is suddenly lost in flight, what indication, if
any, would you have?
E. In what three situations will the landing gear horn activate?
F. What unit will not allow the gear to be retracted on the ground?

56 Oral Review

G. What is the procedure to extend the gear manually (Emergency

Gear Extension)?
H. What airspeed is of importance during manual gear extension?
I. Are the brake and the landing gear hydraulics interconnected?
J. If you lose gear hydraulics, will you still have brakes?
K. What indicates that the gear is in transit and the hydraulic pump
is activated?
14. What type of braking system is used by the Seminole? Where is the
brake fluid serviced?
15. What type of flaps does the Seminole have?
A. What are the flap settings on the Seminole?
16. What are the maximum taxi, takeoff, and landing weights?
17. What is the maximum baggage capacity?
18. Define VSSE.
19. What are the drag factors on light twins?
20. Who determines VMC for a particular aircraft?
21. Define VMC.
22. Why is an aft CG used in determining VMC?
23. What are the factors in determining VMC?
24. Define critical engine and list the factors used to determine it.
25. What causes an aircraft to sideslip with the loss of an engine, and what
action is required to correct this?
26. How much climb performance is lost when an engine fails?
27. What aircraft equipment checks are required under FAR part 91?
28. Define absolute and single-engine service ceiling.
29. What documents are required to be on the aircraft?
30. Explain lost communications procedures.
31. Will the propeller feather below 950 RPM. Why or why not?
32. Explain the pitot static system.
A. Does the PA-44 have an alternate static source? If so, how is it
activated and what actions are necessary to acquire the most
accurate reading?
B. What instruments are pitot static?
C. Where is the pitot static port located?
33. How do you prevent a heater overheat?
34. What is the fuel capacity? How many gallons are unusable?
Oral Review 57

35. What grade fuel is to be used in the PA-44?

36. How many fuel pumps are on the aircraft?
37. When are the electric fuel pumps to be used?
38. What are the various positions on the fuel selector control?
39. Explain the procedure for cross feeding fuel when operating the right
engine from the left tank.
40. If an engine failure occurred at 5,000' MSL, or a high density altitude,
what would you do to get max performance from the operating engine
after performing the In-Flight Engine Failure Checklist?
41. If the cylinder head temp and oil temp approach the caution range,
what can be done to assist in cooling?
42. Why does manifold pressure decrease approximately 1" every 1,000'
during climb?
43. When an engine is inoperative or feathered, what indication will be
observed on the manifold pressure gauge?
44. Why is the manifold pressure gauge not necessarily a good indicator in
determining an inoperative engine?

Additional Questions Specific to G500-Equipped Aircraft

1. In the event of an electrical failure, what pilot actions are necessary to
ensure continued operation of the standby attitude indicator?
2. If the standby power button on the attitude indicator is not pressed
within one minute of electrical failure, what will happen?
3. How do you determine a standard rate turn on an aircraft with a G500
system?
4. In the event of an AHRS failure, which indications will no longer be
displayed on the PFD? Which indications will still be visible on the PFD?
5. Which approaches can be accomplished with an AHRS failure?
6. What instrument approaches are available with the PFD inoperative?
With the MFD inoperative? With a total PFD/MFD failure?
7. How long does the internal battery last when providing power to the
standby attitude indicator?
8. With the loss of the ADC, which lost instrument does not have
a backup? What should you do to compensate for the lack of
information?

58 Oral Review

Copyright 2015 Airline Transport Professionals.

The content of this manual is furnished for informational use only, and is subject to change without notice. Airline Transport
Professionals assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. This
manual does not replace the Piper Seminole Pilot Operating Handbook, FAA Airplane Flying Handbook, or Practical Test
Standards. Nothing in this manual shall be interpreted as a substitute for the exercise of sound judgement.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means
electronic, mechanical or otherwise, without the prior written permission of Airline Transport Professionals.

World's Largest
Multi-Engine Training Fleet
ATP's training fleet of over 260 aircraft
includes more than 100 multi-engine Piper
Seminoles. This is the largest multi-engine
training fleet in the world, and offers you a
level of certainty and peace-of-mind when
it comes to aircraft availability for your
flight training and checkrides.

Learn more at:

ATPFlightSchool.com