Scientific Atlanta
Scientific Atlanta
Scientific Atlanta
22873
NOTE: The output tilt referenced in this document is defined as a LINEAR output tilt (as opposed to a CABLE output tilt). The distortion
and noise figure specifications are applicable across the full operational temperature range (as opposed to being referenced to 68F).
When calculating end of line performance, the specifications used for all of the amplifiers in a given cascade must be of similar format,
due to the fact that all amplifiers in a cascade must operate with a similar output tilt (either all LINEAR output tilt or all CABLE output tilt).
DESCRIPTION
The Type 2A-2 RF amplifier module
offers a high performance design
solution for the latest HFC networks.
FEATURES
Integrated reverse amplifier, with optimized diplex filter group delay for
forward and reverse paths
Individual reverse input testpoints and input pads for both the Main and Aux
reverse inputs allowing optimum reverse path alignment
Improved station frequency response
Unitized design (amplifier and power supply in a single module) enabling
simplified and faster maintenance
High efficiency, transformerless power supply lowering system operating cost
Directional Coupler RF testpoints provides optimum accuracy
Surge Resistant Circuitry ensuring hybrid protection without fuses or other
nuisance failure causing devices
Scientific-Atlanta 1-800-433-6222
22884
Forward
Input
-20 dB T.P.
FWD
Input
Forward
Aux Output
-20 dB T.P.
HPF
Pad
EQ
TRIM
AGC
Pad
ISEQ
AC
Bypass
AGC
Coupler
FWD
AC
Bypass
REV
Aux 1
REV
Aux
Pad
Fuse
Shunt
Reverse Output
-20 dB T.P.
Reverse Aux
Input -20 dB T.P.
Fuse
Shunt
Rev
Pad
Pad
Rev
EQ
LPF
Forward
Main Output
-20 dB T.P.
-20 dB
Reverse Inj.
Main
Pad
FWD
Rev
Pad
REV
Fuse
Shunt
AC
Bypass
Reverse
Main Input
-20 dB T.P.
Main
T6021
Units
MHz
--degrees
dB
dB
dB
Amps
Amps
dB
Forward
70-750
PHD
-40 to +60 C
0.5
4
16
15
25
66 (70-750 MHz)
dB
56 (70-150 MHz)
59 (151-600 MHz)
55 (601-750 MHz)
1.37
-20
16.5 - fixed
AGC w/ manual temp backoff
37
+12
10.5
10
N/A
47.5 @ 750 MHz
44 @ 550 MHz
35 @ 70 MHz
+12.5
Current Draw @ 24 V DC
Test Points (0.5 dB)
Interstage Equalizer (value - type)
Interstage Level Control (type)
Operational Gain (minimum) 3, 9
Internal Tilt 2 (0.5 dB)
Noise Figure 3, 8 @ 70 MHz
Noise Figure 3, 8 @ 750 MHz
Reverse Noise Figure 8,9
Reference Output LevelHigh Freq.
Amps
dB
dB
dB
dB
dB
dB
dB
dBmV
dBmV
dB
Reverse
5-55
PP
-40 to +60 C
0.5
N/A
16
N/A
N/A
60 (5-15 MHz)
70 (16-55 MHz)
50 (5-15 MHz)
58 (16-55 MHz)
0.09
-20
N/A
N/A
18
0
N/A
N/A
10
35 @ 55 MHz 7
35 @ 5 MHz 7
flat
Units
NTSC
dB
dB
dB
Forward
76 w/ digital 4
70
68
64
Reverse
6
92
80
82
Delay Characteristics
Forward
(Chrominance to Luminance Delay)
Freq. (MHz)
Delay (ns)
72.00 - 76.43
28
91.25 - 94.83
4
Reverse
(Group Delay in 1.5 MHz BW)
Freq. (MHz)
Delay (ns)
58.5 - 55.0
25
48.5 - 50.0
8
10.0 - 11.5
6
5.0 - 6.5
62
Notes:
(1) Reference output tilt is specified as LINEAR tilt (as opposed to traditional cable tilt).
(2) Down tilt, the effect of cable, is represented by a (-). Up tilt, the effect of equalization, is represented by a (+).
(3) Forward gain and noise figure measured with 0 dB input EQ and 1 dB input pad.
(4) Digital refers to 550-750 MHz loading with 33 QAM carriers at -6 dB levels relative to analog video carrier levels.
(5) CTB and CSO measured using CW carriers, with spectrum analyzer as the measurement device.
(6) X-Mod (@ 15.75 kHz) specified using 100% synchronous modulation and frequency selective measurement device.
(7) Reverse output reference level with a 0 dB reverse output equalizer and factory selected reverse output pad.
(8) Distortions and Noise Figures are typical and specified over the operational temperature range.
(9) Reverse gain and noise figure for station, with 0 dB reverse input pad, 0 dB reverse output EQ, and factory-selected reverse output pad.
Unless otherwise noted, the above specifications reflect typical station performance at stated reference levels in the recommended operating configuration,
including the input equalizer and reverse filters where applicable. Unless otherwise noted, specifications are based on measurements made in accordance
with NCTA Practices for Measurements on Cable Television Systems using standard frequency assignments and are referenced to 68F (20C).
I DC
AC Voltage
90
85
80
75
70
65
60
55
50
45
40
35
AC Current (A)
1.46 0.58 0.61 0.64 0.66 0.68 0.71 0.74 0.78 0.85 0.94 1.05 1.21
Power (W)
39.9 39.9 39.9 39.5 39.3 39.1 39.1 39.1 40.2 39.7 39.6 39.7
Data is based on stations configured for 2-way operation. AC currents specified are based on measurements made with typical CATV
type ferro-resonant AC power supply (quasi-square wave).
(Amps)
ORDERING INFORMATION
Amplifier Module - 1 required
# 573863 - Type 2A-2 amplifier module with AGC. AGC has
451.25 MHz pilot frequency and manual temperature backoff
control.
Note: Amplifier module also comes configured with reverse
amplifier, reverse combiner, 16.5 dB interstage EQ, interstage
pad, output pads, 0 dB reverse output EQ, 55/70 diplex filters,
and integrated power supply. Power supply has 30 V AC
undervoltage lockout (40 V AC is field configurable).
Optional Accessories
#467351 230 V AC Crowbar Surge Protector
Plug-in Cable Simulator. Simulates cable losses, creating tilt
opposite that of Equalizers. Use in place of Forward Input
Equalizer as needed to maintain proper output tilt in short
spaced locations. Available in 1.5 dB steps from 1.5 dB to
12.0 dB cable loss at 750 MHz. Order Model CS 750-*
(* denotes CS value); specify value.
Related Equipment
#501111 Long Reach Test Point Adapter
#276982 Reverse Injection Probe (3 dB insertion loss)
#548771 Pad Insertion/Removal Tool
MECHANICAL SPECIFICATIONS
Required Accessories
Plug-in Pads (attenuators):
1 required for forward (1 input)
3 required for reverse (2 inputs, 1 output)
1 required for AGC only if amplifier main output level at
pilot frequency is NOT 42 dBmV (AGC comes configured
with a 5 dB pad, which is appropriate for 42 dBmV main
output level at pilot frequency).
Available in 0.5 dB steps from 0 to 20 dB. Order Model PP-*
(* denotes pad value), specify value.
Housing Dimensions
17.3 in. L x 4.8 in. H x 7.8 in. D
438.3 mm L x 122.4 mm H x 198.7 mm D
Weight
Housing
9 lbs, 9 oz; 4.4 kg
Module
4 lbs, 13 oz; 2.2 kg
Specifications and product availability are subject to change without
notice.
Scientific Atlanta and the Scientific-Atlanta logo are registered trademarks
of Scientific-Atlanta, Inc.
Surge Resistant is a trademark of Scientific-Atlanta, Inc.
Scientific-Atlanta, Inc.
http://www.sciatl.com
United States: 4261 Communications Drive, P.O. Box 6850, Norcross, GA 30091-6850; Tel: 800-722-2009; Fax: 770-903-4617
Germany: Europe GmbH, 61476 Kronberg, Germany; Tel: 49-6173-928-000; Fax: 49-6173-928-150
Australia: Unit 2, 2 Aquatic Drive, P.O. Box 292, Frenchs Forest, NSW 2086, Australia; Tel: 61-2-9452-3388; Fax: 61-2-9451-4432
Singapore: 1 Claymore Drive, #08-11 Orchard Towers, Singapore 229594; Tel: 65-733-4314; Fax: 65-733-2706
Hong Kong: Suite 56 & 57, 5/F New Henry House, 10 Ice House Street, Central, Hong Kong; Tel: 852-2522-5059; Fax: 852-2522-5624
P/N 587988 Rev A
Printed in USA.
1298M